OWNER’S MANUAL
DVD Player
Please read this manual carefully before operating
your set and retain it for future reference.
DP540H / DP542H
www.lg.com
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not
try to open the enclosure.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
Getting Started
This device is equipped with a portable battery or
accumulator.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
Notes on Copyrights
yy This product incorporates copyright protection
technology that is protected by U.S. patents
and other intellectual property rights. Use of
this copyright protection technology must be
authorized by Rovi Corporation, and is intended
for home and other limited viewing uses only
unless otherwise authorized by Rovi Corporation.
Reverse engineering or disassembly is prohibited.
yy Under the U.S. Copyright laws and Copyright
laws of other countries, unauthorized recording,
use, display, distribution, or revision of television
programs, videotapes, DVDs, CDs and other
materials may subject you to civil and/or criminal
liability.
Disposal of your old appliance
1.When this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by the
European Directive 2002/96/EC.
2.All electrical and electronic products
should be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or the
local authorities.
3.The correct disposal of your old
appliance will help prevent potential
negative consequences for the
environment and human health.
4.For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you
purchased the product.
Disposal of waste batteries/
accumulators
1.When this crossed-out wheeled
bin symbol is attached to batteries/
accumulators of Your product it means
they are covered by European Directive
2006/66/EC.
2.This symbol may be combined with
chemical symbols for mercury(Hg),
cadmium(Cd) or lead(Pb) if the battery
Contains more that 0.0005% of
mercury,0.002% of cadmium or 0.004%
of lead.
3.All batteries/accumulators should be
disposed separately from the municipal
waste stream via designated collection
facilities appointed by the government
or the local authorities.
4.The correct disposal of Your old
batteries/accumulators will help
to prevent potential negative
consequences for the environment,
animal and human health.
5.For more detailed information
about disposal of Your old batteries/
accumulators, please contact Your city
office, waste disposal service or the
shop where You purchased the product.
LG Electronics hereby declares that this/these
product(s) is/are in compliance with the essential
requirements and other relevant provisions of
Directive 2004/108/EC, 2006/95/EC, 2009/125/EC
and 2011/65/EU.
Contact office for compliance of this product :
LG Electronics Inc.
EU Representative, Krijgsman 1,
1186 DM Amstelveen, The Netherlands
yy Please note that this is NOT a Customer Service
contact point. For Customer Service Information,
see Warranty Card or contact the dealer that you
purchased this product.
1
Getting Started
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
3
4
Getting Started
Notes on Discs
1
yy Do not touch the playback side of the disc. Hold
the disc by the edges so that fingerprints do not
get on the surface. Never stick paper or tape on
the disc.
Getting Started
yy After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of
heat and never leave it in a parked car exposed
to direct sunlight.
Notes on the Unit
yy Please save the original shipping carton and
packing materials. If you need to ship the unit,
for maximum protection, re-pack the unit as it
was originally packed at the factory.
yy To clean the unit, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth
lightly moistened with a mild detergent solution.
Do not use strong solvents such as alcohol,
benzine, or thinner, as these might damage the
surface of the unit.
yy The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest
authorized service center.
Table of Contents
5
Table of Contents
1
Getting Started
2
Safety Information
6Introduction
6
– About the “7” Symbol Display
6
– Symbols Used in this Manual
6
– Supplied Accessories
6
– Playable Discs
6
– Regional Code
7
– File Compatibility
8
Remote Control
9
Front Panel
9
Rear Panel
4Operating
15
15
15
15
16
16
16
17
General Playback
– Playing a Disc
– Playing a File
– On-Screen Display
– General Operation
Advanced Playback
– Movie
– Music
1
2
3
5Troubleshooting
19Troubleshooting
2Connecting
10
10
10
11
11
12
12
12
12
Connecting to your TV
– Connecting RCA to SCART Cable
– Connecting Component Video Cable
– Connecting HDMI Cable
– Resolution Setting
Connecting to an Amplifier
– Connecting Audio Cable
– Connecting COAXIAL (digital audio)
Cable
– Connecting HDMI Cable
3 System Setting
13Settings
13 – Adjust the Setup Settings
13 – [LANGUAGE] Menu
13 – [DISPLAY] Menu
14 – [AUDIO] Menu
14 – [LOCK] Menu
14 – [OTHERS] Menu
6Appendix
20 Area Code List
21 Language Code List
22Specifications
22 Trademarks and Licenses
4
5
6
6
Getting Started
Introduction
Playable Discs
DVD-VIDEO
1
About the “7” Symbol Display
Getting Started
“7” may appear on your TV display during
operation and indicates that the function explained
in this owner’s manual is not available on that
specific media.
Symbols Used in this Manual
A section whose title has one of the following
symbols are applicable only to the disc or file
represented by the symbol.
r
t
DVD-Video, DVD±R/RW
Audio CDs
y
Video files contained in the
USB/Disc (USB: DP542H only)
u
Audio files contained in the
USB/Disc (USB: DP542H only)
i
Photo files contained in the
USB/Disc (USB: DP542H only)
Supplied Accessories
Discs such as movies that can be
purchased or rented.
DVD±R
-- Video mode and finalized only
-- Supports the dual layer disc also
-- DVD±R discs that contain Video,
Audio or Photo files.
DVD-RW
-- VR mode, Video mode and
finalized only
-- DVD-RW discs that contain Video,
Audio or Photo files.
DVD+RW
-- Video mode and finalized only
-- DVD+RW discs that contain Video,
Audio or Photo files.
Audio CD
CD-R/RW
-- CD-R/RW discs that contain audio
titles, Video, Audio or Photo files.
,,Note
Battery (1)
Remote control (1)
You have to set the disc format option
to [Mastered] in order to make the discs
compatible with the players when formatting
rewritable discs. When setting the option
to Live System, you cannot use it on player.
(Mastered/Live File System: Disc format system
for windows Vista)
Regional Code
This unit has a regional code printed on the rear of
the unit. This unit can play only DVD discs labeled
same as the rear of the unit or “ALL”.
Getting Started
File Compatibility
7
Photo Files
Photo size: Less than 2M recommended.
Overall
yy The file name is limited to 45 characters.
yy Depending on the size and number of the files,
it may take several minutes to read the contents
on the media.
Maximum Files/Folder: Less than 600 (total
number of files and folders)
yy Progressive and lossless compression photo
image files are not supported.
Notes of USB Device (DP542H only)
yy This unit supports USB device with FAT16 or
FAT32 format.
yy Do not extract the USB device during operation
(play, etc.).
CD-R/RW, DVD±R/RW Format: ISO 9660
yy A USB device which requires additional program
installation when you have connected it to a
computer, is not supported.
Video Files
yy USB device: USB device that supports USB1.1
and USB2.0.
Available resolution size: 720 x 576 (W x H) pixels
Playable subtitle: SubRip (.srt/.txt), SAMI (.smi),
SubStation Alpha (.ssa/.txt), MicroDVD (.sub/
.txt), SubViewer 2.0 (.sub/.txt), TMPlayer (.txt), DVD
Subtitle System (.txt)
Playable Codec format: “DIVX3.xx”, “DIVX4.xx”,
“DIVX5.xx”, “DIVX6.xx” (Standard playback only),
“MP43”, “3IVX”
Playable Audio format: “Dolby Digital”, ”PCM”,
“MP3”, “WMA”
Sampling frequency: within 8 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
Bit rate (MP3/WMA/DivX): within 8 to 320 kbps
(MP3), within 32 to 192 kbps (WMA), less than 4
Mbps (DivX)
,,Note
This unit does not support files that are
recorded with GMC*1 or Qpel*2. Those are video
encoding techniques in MPEG4 standard, like
DivX have.
*1GMC – Global Motion Compensation
*2Qpel – Quarter pixel
Audio Files
Sampling frequency: within 8 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
Bit rate: within 8 to 320 kbps (MP3), within 32 to
192 kbps (WMA)
yy Movie, music and photo files can be played. For
details of operations on each file, refer to relevant
pages.
yy Regular back up is recommended to prevent
data loss.
yy If you use a USB extension cable, USB HUB, USB
Multi-reader, or External HDD, the USB device
may not be recognized.
yy Some USB device may not work with this unit.
yy Digital camera and mobile phone are not
supported.
yy USB Port of the unit cannot be connected to PC.
The unit cannot be used as a storage device.
1
Getting Started
Available File extensions: “.avi”, “.mpg”, ”.mpeg”,
“.mp3”, “.wma”, “.jpg”, “.jpeg”, “.divx”
8
Getting Started
Remote Control
DISPLAY: Accesses or exits On-Screen Display.
1
RETURN (x): Moves backward or exit the menu.
Getting Started
AUDIO ([): Selects an audio language or audio
channel.
SUBTITLE (]): Selects a subtitle language.
ANGLE (}): Selects a DVD camera angle, if
available.
SETUP: Accesses or exits the setup menu.
• • • • • • • • • • d• • • • • • • • • • •
MARKER: Marks any point during playback.
SEARCH: Displays MARKER SEARCH menu.
PROGRAM: Enters the program edit mode.
ZOOM: Enlarges video image.
REPEAT: Repeats a chapter, track, title or all.
A-B: Repeats a section.
• • • • • • • • • • a• • • • • • • • • • •
POWER (1): Switches the unit ON or OFF.
OPEN/CLOSE (B): Opens and closes the disc tray.
Numerical buttons: Selects numbered items in a
menu.
CLEAR: Removes a track number on the Program
List or the Marker Search menu.
TV Control Buttons: Control the sound volume,
channel, sources, and power On/Off on TV.
• • • • • • • • • • b• • • • • • • • • • •
SCAN (c/v): Searches backward or forward.
SKIP (C/V): Goes to the next or previous
chapter / track / file.
RESOLUTION: Sets the output resolution for HDMI
OUTPUT and COMPONENT/PROGRESSIVE SCAN
OUTPUT jack.
?: This button is not available.
Battery Installation
Remove the battery cover on the rear of the Remote
Control, and insert R03 (size AAA) battery with 4
and 5 matched correctly.
Code number to control TVs
While holding down TV POWER button, press the
number buttons to select the Maker code for your TV
(see the table below). Release TV POWER button.
Maker
Code Number
LG
1(Default), 2
PLAY (z): Starts playback.
Zenith
1, 3, 4
STOP (Z): Stops playback.
GoldStar
1, 2
Samsung
6, 7
Sony
8, 9
Hitachi
4
PAUSE/STEP (M): Pauses playback.
• • • • • • • • • • c• • • • • • • • • • •
DVD MENU: Accesses or exits the DVD menu.
TITLE: Accesses the disc’s title menu, if available.
w/s/a/d: Navigates the menus.
ENTER (b): Confirms menu selection.
Getting Started
9
Front Panel
1
a Disc Tray
eT (Play/Pause)
b Display window
f1/! (Power)
c Remote sensor
gUSB Port (DP542H only)
d R (Open/Close)
Rear Panel
ͦ
ͧ
a AC power cord
d DIGITAL AUDIO OUT (COAXIAL)
b VIDEO OUT
e AUDIO OUT (Left/Right)
c COMPONENT VIDEO OUT (Y PB PR)
fHDMI OUT
g
Getting Started
ͦ ͧ
10
Connecting
Connecting to your TV
Connecting RCA to SCART
Cable
2
Using the RCA to SCART cable, connect the RCA
cable ends to the corresponding VIDEO/AUDIO
OUTPUT jacks on the unit and connect the scart
cable to the scart socket on the TV.
Connecting Component Video
Cable
Connect the COMPONENT/PROGRESSIVE SCAN
OUTPUT jacks on the unit to the corresponding
input jacks on the TV using Component video
cable, such as Y with green, Pb with blue, and Pr
with red.
Connecting
Rear of the Unit
Rear of the Unit
Component
Cable
RCA to SCART cable
TV
VIDEO IN
Y
L
PB
COMPONENT VIDE
TV
yy You should still connect the AUDIO cable
between the unit and TV.
Connecting
11
Connecting HDMI Cable
Resolution Setting
Connect the HDMI OUTPUT on the unit to the
HDMI IN on compatible TV with HDMI cable. (Type
A, High Speed HDMI™ Cable)
You can change the resolution using RESOLUTION
button.
Rear of the Unit
TV
COAXIAL
Additional Information for HDMI
yy When you connect a HDMI or DVI compatible
device, make sure of the following:
-- Try switching off the HDMI/DVI device and this
unit. Next, switch on the HDMI/DVI device and
leave it for around 30 seconds, then switch on
this unit.
-- The connected device’s video input is set
correctly for this unit.
-- The connected device is compatible with
720x576i(480i), 720x576p(480p), 1280x720p,
1920x1080i or 1920x1080p video input.
-- The 1080p, 720p and 576p(480p) resolutions are
the progressive scan applied resolution.
yy Not all HDCP-compatible DVI devices will work
with this unit.
-- The picture will not be displayed properly with
non-HDCP device.
yy For 720p, 1080p and 1080i resolution on the
component / progressive scan output, only noncopy protected discs can be played back. If the
disc is copy protected, it will be displayed at the
576p(480p) resolution.
yy Depending on your TV, some of the resolution
settings may result in the picture disappearing
or an abnormal picture appearing. In this case,
press RESOLUTION repeatedly until the picture
re-appears.
2
Connecting
HDMI Cable
yy The unit is able to provide a 1080p full HD image
to most 1080p-capable TVs in the market today.
However, there are some 1080p TVs available
from certain companies that are limited in the
types of 1080p images that can be accepted.
Specifically, 1080p-capable TVs that don’t accept
images in 60Hz can’t display an image from this
unit.
12
Connecting
Connecting to an
Amplifier
Connecting Audio Cable
2
Connect the AUDIO OUTPUT on the unit to 2CH
AUDIO IN on amplifier with Audio cable, such as
AUDIO Left/Right with white/red.
yy If your TV is not capable of handling 96 kHz
sampling frequency, set the [Sample Freq.]
option to [48 kHz] on the setup menu.
yy If your TV is not equipped with Dolby Digital
and MPEG decoder, set the [Dolby Digital] and
[MPEG] options to [PCM] on the setup menu.
yy Changing the resolution when the unit is
connected with HDMI connector may result in
malfunctions. To solve the problem, turn off the
unit and then turn it on again.
Connecting
,,Note
Audio
Cable
Rear of the Unit
Receiver /
Amplifier
Connecting COAXIAL (digital
audio) Cable
Connect one of the unit’s DIGITAL AUDIO OUTPUT
(COAXIAL) jacks to the corresponding jack on your
amplifier.
yy If the audio format of the digital output
does not match the capabilities of your
amplifier, the amplifier will produce a strong,
distorted sound or no sound at all.
yy To see the audio format of the current disc
in the on-screen display, press AUDIO.
yy This unit does not perform internal (2
channel) decoding of a DTS sound track.
To enjoy DTS multi channel surround, you
must connect this unit to a DTS compatible
amplifier via one of this unit’s digital audio
outputs.
Connecting HDMI Cable
Connect the HDMI OUTPUT on the unit to the
HDMI IN on amplifier with HDMI cable.
(Type A, High Speed HDMI™ Cable)
Connect the HDMI OUT jack on amplifier to HDMI
IN jack on TV with HDMI cable, if the amplifier has
HDMI OUTPUT jack.
Rear of the Unit
Rear of the Unit
HDMI
Cable
Coaxial
Cable
Receiver /
Amplifier
OPTICAL
TV
COAXIAL
HDMI
Cable
OUT
Receiver /
Amplifier
System Setting
Settings
When the unit is turned-on at the first time, you
have to select the desired language. (Optional)
Adjust the Setup Settings
You can change the settings of the unit in the
[Setup] menu.
1. Press SETUP.
2.Use w/s to select the first setup option, and
press d to move to the second level.
3.Use w/s to select a second setup option, and
press d to move to the third level.
[DISPLAY] Menu
TV Aspect
Select which screen aspect to use based on the
shape of your TV screen.
[4:3]: Select when a standard 4:3 TV is
connected.
[16:9]: Select when a 16:9 wide TV is
connected.
Display Mode
If you selected 4:3, you’ll need to define how you
would like widescreen programs and films to be
displayed on your TV screen.
[LANGUAGE] Menu
[Letterbox]: This displays a widescreen picture
with black bands at the top and bottom of the
screen.
Menu Language
[Panscan]: This fills the entire 4:3 screen,
cropping the picture as necessary.
Select a language for the Setup menu and onscreen display.
Disc Audio/Disc Subtitle/Disc Menu
Select a language for the Disc Audio/Disc Subtitle/
Disc Menu.
[Original]: Refers to the original language in
which the disc was recorded.
[Other]: To select another language, press
number buttons then ENTER (b) to enter the
corresponding 4-digit number according to
the language code list. (See page 21) If you
make a mistake while entering number, press
CLEAR to delete numbers then correct it.
[Off] (for Disc Subtitle): Turn off Subtitle.
3
System Setting
4.Use w/s to select a desired setting, and press
ENTER (b) to confirm your selection.
13
14
System Setting
[AUDIO] Menu
Password
Set the player’s Audio options according to various
disc output type you use.
Sets or changes the password for lock settings.
Dolby Digital / DTS / MPEG
To input the standardized area code referring the
Area Code List on page 20.
Select the type of digital audio signal to use the
DIGITAL AUDIO OUTPUT jack.
[Bitstream]: Select to connect DIGITAL AUDIO
OUTPUT jack to an amplifier with Dolby Digital,
DTS or MPEG decoder.
3
Area Code
[OTHERS] Menu
B.L.E (Black Level Expansion)
System Setting
[PCM] (for Dolby Digital / MPEG): Select
to connect DIGITAL AUDIO OUTPUT jack to
an amplifier without Dolby Digital or MPEG
decoder.
Select On or Off to expand the black level or not. It
just operates when TV system is set to NTSC.
[Off] (for DTS): Select to connect DIGITAL
AUDIO OUTPUT jack to an amplifier without
DTS decoder.
ABOUT DIVX VIDEO: DivX® is a digital video
format created by DivX, LLC, a subsidiary of Rovi
Corporation. This is an official DivX Certified®
device that has passed rigorous testing to verify
that it plays DivX video. Visit divx.com for more
information and software tools to convert your files
into DivX videos.
Sample Freq. (Frequency)
Selects the sampling frequency of the audio signal
between [48 kHz] and [96 kHz].
DRC (Dynamic Range Control)
Make the sound clear when the volume is turned
down (Dolby Digital only). Set to [On] for this effect.
Vocal
Set to [On] only when a multi-channel karaoke DVD
is playing. The karaoke channels on the disc mix
into normal stereo sound.
[LOCK] Menu
Firstly, you have to create the 4-digit password on
[Area Code] to use the LOCK menu.
If you forget your password
You can reset it. First, remove the disc in the
unit. Display setup menu then input the 6-digit
number “210499”. The “P CLr” appear in the
display window and the password is deleted.
Rating
Select a rating level. The lower the level, the stricter
the rating. Select [Unlock] to deactivate the rating.
DivX(R) VOD
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order to play
purchased DivX Video-on-Demand (VOD) movies.
To obtain your registration code, locate the DivX
VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete
your registration.
[Register]: Displays the registration code of
your unit.
[Deregister]: Deregister your unit and display
the deregister code.
Operating
15
General Playback
On-Screen Display ry
Playing a Disc rt
1. While playback, press DISPLAY to show various
playback information.
1. Press OPEN/CLOSE (B), and place a disc on the
disc tray.
2. Press OPEN/CLOSE (B) to close the disc tray
For the most DVD-ROM discs, playback starts
automatically.
For the Audio CD, select a track using w/s/
a/d, and press PLAY (z) or ENTER (b) to
play the track.
Playing a File yui
1. Press OPEN/CLOSE (B) to place a disc on the
disc tray, or connect the USB device. (USB: DP542H only)
RETURN (x)
Changes between Disc and
USB Device.
TITLE
Changes the mode. (Music :
Photo : Movie)
2. Select an option using w/s.
3.Use a/d and numerical button to adjust the
selected option value.
4. Press DISPLAY to exit the On-Screen display.
Current title number/total
number of titles
Current chapter number/total
number of chapters
Elapsed playing time
Selected total time of current
title/file
Selected audio language or
channel
Selected subtitle
Selected angle/total number
of angles
4
Operating
2. Select a file using w/s/a/d, and press PLAY
(z) or ENTER (b) to play the file.
You can display and adjust various information and
settings about the content.
16
Operating
General Operation
To
Do this
Playback
Press PLAY (z)
Movie ry
Pause
Press PAUSE/STEP (M)
To
Do this
Press STOP (Z)
Display disc
menu
Press DVD MENU. (DVD Only)
Play
repeatedly
Press REPEAT during playback. To
select an option to be repeated,
Press REPEAT repeatedly.
Stop
Skip to the next Press C or V during
or previous
playback
Fast forward or Press c or v during
fast reverse
playback.
Resume
playback
Press STOP (Z) during playback
to save the stopped point.
yy Press STOP (Z) once:
Displayed MZ on the screen
(Resume Stop)
4
Advanced Playback
yy Press STOP (Z) twice:
Displayed Z on the screen
(Complete Stop)
Operating
System Select
Screen Saver
Last Scene
Memory
You must select the appropriate
system mode for your TV system.
Remove any disc that might
be in the unit, press and hold
PAUSE/STEP (M) for more than
five seconds to be able to select
a system (PAL, NTSC).
Leave the unit in Stop mode for
about five minutes, then the
screen saver appears.
If the Screen Saver is displayed
for five minutes, the unit automatically turns itself off.
Turn off the unit, then the unit
memorize the lastly viewed
scene even if disc is inserted
again after removal or unit is
turned on after off with same
disc. (DVD/ Audio CD only)
• DVD: Chapter/ Title/ Off
• MOVIE: Track/ All/ Off
Play frame-by- Press PAUSE/STEP (M) while
frame
Video file playback and press
PAUSE/STEP (M) repeatedly to
play Frame-by-Frame playback.
Repeat a
specific
portion
Press A-B at the beginning of the
portion you wish to repeat and
again at the end of the portion.
To return to normal playback,
press A-B to select [Off ].
Set the desired Searches for the starting point
starting time of of entered time code. Press
playback
DISPLAY then select clock
icon. Enter a time then press
ENTER(b).
For example, to find a scene
at 1 hour, 10 minutes, and 20
seconds, enter “11020” and press
ENTER(b).
If you enter the wrong number,
press CLEAR to enter again.
Mark a favorite Press MARKER at the desired
scene
position up to nine markers.
Press SEARCH to recall or clear
position. Use a or d to select
a desired marker, then press
ENTER(b) to recall it or CLEAR
to clear it.
Change the
Press and hold SUBTITLE for 3
subtitle code seconds during playback. The
page
language code will appear.
(Video file
Press a or d to select another
only)
language code until the subtitle
is displayed properly and then
press ENTER (b)
Operating
Slow down the While the playback is paused,
playing speed press v repeatedly to play
(Forward only) various speeds of slow motion.
Press PLAY (z) to continue play
at normal speed.
Watch an
During playback or pause mode,
enlarged video press ZOOM repeatedly to select
zoom mode.
ZOOM: 100% : 200% : 300%
: 400% : 100%
w/s/a/d: Move through the
zoomed picture.
17
Music tu
To
Do this
Play
repeatedly
Press REPEAT during playback.
To select an item to be repeated,
Press REPEAT repeatedly.
• TRACK/ ALL/ (REPEAT Off )
Create or
delete your
own program
Press the PROGRAM to select
desired file and then, { mark
appears on screen.
Using w/s and ENTER (b)
to add a music file(s) on the
program list,
If you add desired music file(s),
press PROGRAM to end edit
program list.
4
To clear all music file(s) from the
program list, select [Clear All]
then press ENTER (b) in program
edit mode.
Operating
Display file
information
(ID3 TAG)
To clear a music file(s) from the
program list, select the music
file you want to clear then press
CLEAR in program edit mode.
While playing a MP3 file
containing file information, you
can display the information by
pressing DISPLAY repeatedly.
yy Depending on the MP3 files,
information may not be
displayed on the screen.
18
Operating
Photoi
To
Do this
View photo
files as a slide
show
Use w/s/a/d to highlight
(`) icon then press ENTER (b)
to start slide show.
Adjust slide
show speed
You can change slide show
speed using a/d when (J)
icon is highlighted.
Rotate a photo Use w/s to rotate the photo in
full screen counterclockwise or
clockwise while viewing a photo
in full screen.
Watch an
While viewing a photo in full
enlarged Photo screen, press ZOOM repeatedly
to select zoom mode.
4
ZOOM: 100% : 200% : 300%
: 400% : 100%
w/s/a/d: Move through the
zoomed photo.
Operating
Listen to music You can listen to music during
during slide
slide show, if the disc contain
show
music and photo files together.
Use w/s/a/d to highlight
(~) icon then press ENTER (b)
to start slide show.
Troubleshooting
19
Troubleshooting
Symptom
Cause
Solution
No power.
The power cord is disconnected.
Plug the power cord into the wall outlet
securely.
The power is on, but
the unit does not work.
No disc is inserted.
Insert a disc.
The unit does not start
playback.
An unplayable disc is inserted.
Insert a playable disc. (Check the disc type
and regional code.)
The rating level is set.
Change the rating level.
The remote control
The remote control is not
does not work properly. pointed at the remote sensor
on the unit.
Point the remote control at the remote
sensor of the unit.
Operate the remote control closer to the unit.
Poor picture quality
and sound distortion.
Fingerprints and dust are
stained on the disc.
Wipe the disc from the center to out with
a clean cloth. Do not use strong solvents.
(alcohol, benzine, thinner, commercially
available cleaners)
No picture.
The TV is not set to receive the
signal from the unit.
Select the appropriate video input mode on
the TV.
The video cable is not
connected securely.
Connect the video cable securely.
The TV does not accept the
Press RESOLUTION repeatedly to select
resolution that is set on the unit. appropriate resolution.
No sound.
The equipment connected with
the audio cable is not set to
receive the signal from the unit.
Select the correct input mode of the audio
amplifier.
The AUDIO options are set to
the wrong position.
Set the AUDIO settings to the correct
position.
5
Troubleshooting
The remote control is too far
from the unit.
20 Appendix
Area Code List
Choose an area code from this list.
AreaCode AreaCode AreaCode AreaCode
Afghanistan AF Fiji FJ Monaco MC Singapore SG
SK
Argentina AR Finland FI Mongolia MN Slovak Republic Australia AU France FR Morocco MA Slovenia Austria AT Germany DE Nepal NP South Africa ZA
Belgium BE Great Britain GB Netherlands NL South Korea KR
Bhutan BT Greece GR Antilles AN Spain ES
Bolivia BO Greenland GL New Zealand NZ Sri Lanka LK
SI
Brazil BR Hong Kong HK Nigeria NG Sweden SE
Cambodia KH Hungary HU Norway NO Switzerland CH
Canada CA India IN Oman OM Taiwan TW
Chile CL Indonesia ID Pakistan PK Thailand China CN Israel IL Panama PA Turkey TR
Colombia CO Italy IT Paraguay PY Uganda UG
Congo CG Jamaica JM Philippines PH Ukraine UA
Costa Rica CR Japan JP Poland PL United States US
Croatia HR Kenya KE Portugal PT Uruguay UY
Czech Republic CZ Kuwait KW Romania RO Uzbekistan UZ
Denmark DK Libya Ecuador EC Luxembourg Egypt EG Malaysia 6
El Salvador SV Maldives MY Saudi Arabia MV Senegal Appendix
Ethiopia ET Mexico MX
LY Russian
LU Federation Vietnam RU Zimbabwe SA
SN
TH
VN
ZW
Appendix
21
Language Code List
Use this list to input your desired language for the following initial settings: [Disc Audio],
[Disc Subtitle] and [Disc Menu].
LanguageCode
LanguageCode
LanguageCode
Afar 6565
French 7082
Lithuanian 7684
Sindhi 8368
Afrikaans 6570
Frisian 7089
Macedonian 7775
Singhalese 8373
Albanian 8381
Galician 7176
Malagasy 7771
Slovak 8375
Amharic 6577
Georgian 7565
Malay 7783
Slovenian 8376
Arabic 6582
German 6869
Malayalam 7776
Spanish 6983
Armenian 7289
Greek 6976
Maori 7773
Sudanese 8385
Assamese 6583
Greenlandic 7576
Marathi 7782
Swahili 8387
Aymara 6588
Guarani 7178
Moldavian 7779
Swedish 8386
Azerbaijani 6590
Gujarati 7185
Mongolian 7778
Tagalog 8476
Bashkir 6665
Hausa 7265
Nauru7865
Tajik 8471
Basque 6985
Hebrew 7387
Nepali 7869
Tamil 8465
Bengali; Bangla 6678
Hindi 7273
Norwegian 7879
Telugu 8469
Bhutani 6890
Hungarian 7285
Oriya 7982
Thai 8472
Bihari 6672
Icelandic 7383
Panjabi 8065
Tonga 8479
Breton 6682
Indonesian 7378
Pashto, Pushto 8083
Turkish 8482
Bulgarian 6671
Interlingua 7365
Persian 7065
Turkmen 8475
Burmese 7789
Irish 7165
Polish 8076
Twi 8487
Byelorussian 6669
Italian 7384
Portuguese 8084
Ukrainian 8575
Chinese 9072
Japanese 7465
Quechua 8185
Urdu 8582
Croatian 7282
Kannada 7578
Rhaeto-Romance 8277
Uzbek 8590
Czech 6783
Kashmiri 7583
Rumanian 8279
Vietnamese 8673
Danish 6865
Kazakh 7575
Russian 8285
Volapük 8679
Dutch 7876
Kirghiz 7589
Samoan 8377
Welsh 6789
English 6978
Korean 7579
Sanskrit 8365
Wolof 8779
Esperanto 6979
Kurdish 7585
Scots Gaelic 7168
Xhosa 8872
Estonian 6984
Laotian 7679
Serbian 8382
Yiddish 7473
Faroese 7079
Latin 7665
Serbo-Croatian 8372
Yoruba 8979
Fiji 7074
Latvian, Lettish 7686
Shona 8378
Zulu 9085
Finnish 7073
Lingala 7678
6
Appendix
LanguageCode
22 Appendix
Specifications
6
Appendix
Power
requirements
AC 200 - 240 V, 50 / 60 Hz
Power
consumption
9W
Dimensions
(W x H x D)
(360 x 39.5 x 200) mm
Net Weight
(Approx.)
1.14 kg
Operating
temperature
5 °C to 35 °C
Operating
humidity
5 % to 90 %
Laser
Semiconductor laser
Signal system
PAL / NTSC
Bus Power Supply
(USB)
5 V 0 200 mA
(DP542H only)
VIDEO OUTPUT
1.0 V (p-p), 75 Ω, sync
negative, RCA jack x 1
COMPONENT /
PROGRESSIVE
SCAN OUTPUT
(Y) 1.0 V (p-p), 75 Ω, sync
negative, RCA jack x 1,
(Pb)/(Pr) 0.7 V (p-p), 75 Ω,
RCA jack x 2
HDMI OUTPUT
(video/audio)
19 pin (Type A, HDMI™
Connector)
ANALOG AUDIO
OUTPUT
2.0 Vrms (1 kHz, 0 dB),
600 Ω, RCA jack (L, R) x 1
DIGITAL AUDIO
OUTPUT (COAXIAL)
0.5 V (p-p), 75 Ω, RCA jack
x1
Design and specifications are subject to change
without prior notice.
Trademarks and
Licenses
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
DivX®, DivX Certified® and associated logos are
trademarks of Rovi Corporation or its subsidiaries
and are used under license.
Download PDF