6000C Owners Manual - Builder Specialties

Owner’s Manual
Installation and Operation
Models:
6000C
6000C-LP
6000C-IPI
6000C-IPILP
8000C
8000C-LP
8000C-IPI
8000C-IPILP
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
• DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory trained
professionals, or technicians supervised by an NFI
certified professional.
• Leave this manual with
party responsible for use
and operation.
D
DI O N
SC OT
AR
D
WARNING
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and shall be installed.
This appliance may be installed as an OEM
installation in manufactured home (USA
only) or mobile home and must be installed
in accordance with the manufacturer’s
instructions and the Manufactured Home
Construction and Safety Standard, Title 24
CFR, Part 3280 in the United States, or the
Standard for Installation in Mobile Homes,
CAN/CSA Z240 MH Series, in Canada.
This appliance is only for use with the type(s)
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certified kit is used.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
1

Pour demander un exemplaire en français de ce Manuel
du propriétaire, visitez www.heatnglo.com/translations.
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
A. Congratulations
This owner’s manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.
Congratulations on selecting a Heat & Glo gas fireplace, an
elegant and clean alternative to wood burning fireplaces.
The Heat & Glo gas fireplace you have selected is designed
to provide the utmost in safety, reliability, and efficiency.
The information contained in this owner’s manual, unless
noted otherwise, applies to all models and gas control
systems.
As the owner of a new fireplace, you’ll want to read and
carefully follow all of the instructions contained in this
owner’s manual. Pay special attention to all cautions and
warnings.
Your new Heat & Glo gas fireplace will give you years of
durable use and trouble-free enjoyment. Welcome to the
Heat & Glo family of fireplace products!
Homeowner Reference Information
We recommend that you record the following pertinent
information about your fireplace.
Model Name: ___________________________________________ Date purchased/installed: __________________
Serial Number:__________________________________________ Location on fireplace: _____________________
Dealership purchased from: _______________________________ Dealer Phone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________
Listing Label Information/Location
Type of Gas
Heat & Glo, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
Not for use with solid fuel.
(Ne doit pas entre utilise avec un combustible solide).
Type of Gas (Sorte De Gaz)
Gaz)::
NATURAL GAS
Gas and Electric
Information
The model information regarding your specific fireplace can be found on
the rating plate usually located in the control area of the fireplace.
This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1
in the USA or CAN/CGA B149 installation codes. (Installer l’appareil selon les codes ou reglements
locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)
ANSI Z21XX-XXXX · CSA 2.XX-MXX
Minimum Permissible Gas Supply for Purposes of Input Adjustment.
Approved Minimum (De Gaz) Acceptable
0.0 in w.c.
(Po. Col. d’eau)
Maximum Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Maximum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Minimum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes
ALTITUDE:
MAX. INPUT BTUH:
MIN. INPUT BTUH:
ORIFICE SIZE:
2
0-0000 FT.
00,000
00,000
#XXXXX
IN CANADA
0000-0000FT.
00,000
00,000
#XXXXX
MADE IN USA
Model:
(Modele):
XXXXXXXX
Serial
(Serie):
XXXXXXXX
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
Model Number
Serial Number
Safety Alert Key:
•
•
•
•
DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE: Used to address practices not related to personal injury.
Table of Contents
A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
B. Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6 Termination Locations
1 Listing and Code Approvals
7 Vent Information and Diagrams
A.
B.
C.
D.
E.
F.
G.
H.
Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tempered Glass Specifications . . . . . . . . . . . . . . . . . . . . .
BTU Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-Combustible Materials Specification. . . . . . . . . . . . . .
Combustible Materials Specification . . . . . . . . . . . . . . . . .
Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Requirements for the Commonwealth of Massachusetts . .
7
7
7
7
8
8
8
9
User Guide
2 Operating Instructions
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fan Kit (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . .
Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Controls, Wall Controls and Wall Switches . . . . .
IPI Battery Tray/Battery Installation . . . . . . . . . . . . . . . . .
Control Module Operation . . . . . . . . . . . . . . . . . . . . . . . .
Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . .
Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . .
Lighting Instructions (Standing Pilot) . . . . . . . . . . . . . . . .
After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . .
10
10
11
11
11
11
11
12
12
12
13
14
15
15
3 Maintenance and Service
A.
B.
C.
D.
Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . .
Maintenance Tasks-Qualified Service Technician . . . . . .
Refractory, Grate and Valve Assembly Removal . . . . . . .
Burner Identification/Verification . . . . . . . . . . . . . . . . . . . .
16
17
18
19
Installer Guide
Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . .
Design and Installation Considerations . . . . . . . . . . . . . .
Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . .
Inspect Appliance and Components . . . . . . . . . . . . . . . . .
20
21
21
21
5 Framing and Clearances
A.
B.
C.
D.
Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . .
Constructing the Appliance Chase . . . . . . . . . . . . . . . . . .
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . .
A.
B.
C.
D.
E.
Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
27
27
27
28
8 Vent Clearances and Framing
A.
B.
C.
D.
E.
Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . .
Wall Penetration Framing . . . . . . . . . . . . . . . . . . . . . . . . .
Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . .
Install Attic Insulation Shield . . . . . . . . . . . . . . . . . . . . . . .
Installing the Optional Heat-Zone® Gas Kit . . . . . . . . . . .
39
39
40
40
41
9 Appliance Preparation
A.
B.
C.
D.
Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Non-combustible Board. . . . . . . . . . . . . . . .
Securing and Leveling the Appliance . . . . . . . . . . . . . . . .
42
43
44
44
10 Installing Vent Pipe (DVP and SLP Pipe)
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
Assemble Vent Sections (DVP Pipe Only) . . . . . . . . . . . .
Assemble Vent Sections (SLP Pipe Only) . . . . . . . . . . . .
Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . .
Secure the Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . .
Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . .
Install Decorative Ceiling Components (SLP only). . . . . .
Install Metal Roof Flashing . . . . . . . . . . . . . . . . . . . . . . . .
Assemble and Install Storm Collar . . . . . . . . . . . . . . . . . .
Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . .
Install Decorative Wall Components (SLP only) . . . . . . . .
Heat Shield Requirements for Horizontal Termination . . .
Install Horizontal Termination Cap (DVP and SLP Pipe) .
45
46
46
47
47
48
49
49
50
50
50
51
11 Gas Information
4 Getting Started
A.
B.
C.
D.
A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 25
22
23
23
24
A.
B.
C.
D.
Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . .
52
52
52
52
12 Electrical Information
A.
B.
C.
D.
E.
Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IntelliFire Plus™ Ignition System Wiring . . . . . . . . . . . . .
Standing Pilot Ignition System Wiring . . . . . . . . . . . . . . .
Optional Accessories Requirements . . . . . . . . . . . . . . . .
Electrical Service and Repair . . . . . . . . . . . . . . . . . . . . . .
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
53
53
53
53
55
3
F. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 55
G. Wall Switch Installation for Fan (Optional) . . . . . . . . . . . . 55
13 Finishing
A.
B.
C.
D.
Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . .
Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Elevated Hearth Systems . . . . . . . . . . . . . . . . . . . . . . . . .
56
56
57
60
14 Appliance Setup
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . .
Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . .
Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Burner Top Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ember Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . .
Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install Trim and/or Surround . . . . . . . . . . . . . . . . . . . . . . .
Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
61
61
61
61
61
62
66
66
66
15 Troubleshooting
A. Standing Pilot Ignition System . . . . . . . . . . . . . . . . . . . . . 67
B. IntelliFire Plus™ Ignition System . . . . . . . . . . . . . . . . . . . 69
16 Reference Materials
A.
 B.
C.
D.
Appliance Dimension Diagram . . . . . . . . . . . . . . . . . . . . .
Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . .
Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
72
81
86
 = Contains updated information.
4
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
B. Limited Lifetime Warranty
Hearth & Home Technologies
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies, on behalf of its hearth brands (”HHT”), extends the following warranty for HHT
gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts
Labor
1 Year
2 years
HHT Manufactured Appliances and Venting
Gas
X
X
Wood
X
X
X
3 years
Pellet
EPA
Wood
Coal
X
X
X
X
X
X
X
X
X
Components Covered
Electric Venting
X
X
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
Igniters, electronic components,
and glass
Factory-installed blowers
Molded refractory panels
X
Firepots and burnpots
5 years
1 year
7 years
3 years
10
years
1 year
X
Limited
3 years
Lifetime
X
X
X
X
X
90 Days
X
X
X
X
X
X
X
X
Castings and baffles
X
X
Manifold tubes,
HHT chimney and termination
Burners, logs and refractory
Firebox and heat exchanger
X
X
All replacement parts
beyond warranty period
See conditions, exclusions, and limitations on next page.
4021-645F 02-18-13
Page 1 of 2
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
5
B. Limited Lifetime Warranty (continued)
WARRANTY CONDITIONS:
•
•
•
•
•
This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of
HHT authorized dealers is available on the HHT branded websites.
This warranty is only valid while the HHT appliance remains at the site of original installation.
This warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the appliance
resides.
Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact
the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service
from a dealer other than the dealer from whom you originally purchased the product.
Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges
for parts are not covered by this warranty.
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
• Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.
• Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
• Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts
include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, batteries and the discoloration of glass.
• Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints related to this noise are not covered by this warranty.
• Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to
install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper operation, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/
incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting
caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or
forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7)
installation or use of components not supplied with the appliance or any other components not expressly authorized
and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing;
and/or (9) interruptions or fluctuations of electrical power supply to the appliance.
• Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.
• Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.
• HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Information is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consideration must be given to appliance location and configuration, environmental conditions, insulation and air tightness of
the structure.
This warranty is void if:
•
•
•
The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging
chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,
cracking and discoloration of steel or enamel finishes.
The appliance is subjected to prolonged periods of dampness or condensation.
There is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to, improper chimney or venting installation.
LIMITATIONS OF LIABILITY:
•
The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no
event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.
This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE
EXPRESSED WARRANTY SPECIFIED ABOVE.
4021-645F 02-18-13
6
Page 2 of 2
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
1
Listing and Code Approvals
A. Appliance Certification
MODELS: 6000C, 6000C-IPI, 8000C, 8000C-IPI
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Heater
STANDARD: ANSI Z21.88b-2008 • CSA 2.33a-2008
This product is listed to ANSI standards for “Vented Gas
Fireplace Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.
NOTICE: This installation must conform with local codes.
In the absence of local codes you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in
the U.S.A. and the CAN/CGA B149 Installation Codes in
Canada.
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
B. Tempered Glass Specifications
Hearth & Home Technologies appliances manufactured
with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the Consumer Product Safety Commission (CPSC). The tempered
glass has been tested and certified to the requirements
of ANSI Z97.1 and CPSC 16 CFR 1202 (Safety Glazing
Certification Council SGCC# 1595 and 1597. Architectural Testing, Inc. Reports 02-31919.01 and 02-31917.01).
C. BTU Specifications
Maximum
Input
BTU/h
Minimum
Input
BTU/h
Orifice
Size
(DMS)
US
(0-2000 FT)
30,000
16,000
37
CANADA
(2000-4500 FT)
27,000
14,400
38
US
(0-2000 FT)
29,000
17,000
52
CANADA
(2000-4500 FT)
26,100
15,300
53
US
(0-2000 FT)
35,000
19,000
33
CANADA
(2000-4500 FT)
31,500
17,100
34
US
(0-2000 FT)
34,000
17,000
50
CANADA
(2000-4500 FT)
30,600
15,300
51
Models
(U.S. or Canada)
6000C (NG)
6000C-IPI (NG)
6000C-LP
6000C-IPILP
8000C (NG)
8000C-IPI (NG)
8000C-LP
8000C-IPILP
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
When installing above 2000 feet elevation:
• In the USA: Reduce input rate 4% for each 1000 feet
above 2000 feet.
• In CANADA: Reduce input rate 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
Check with your local gas utility to determine proper
orifice size.
This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements”
which refers to 15 U.S. Code (USC) 2063 stating “…Such
certificate shall accompany the product or shall otherwise
be furnished to any distributor or retailer to whom the
product is delivered.”
Some local building codes require the use of tempered
glass with permanent marking in such locations. Glass
meeting this requirement is available from the factory.
Please contact your dealer or distributor to order.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
7
E. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in
a Vertical Tube Furnace at 750 ºC shall be considered
non-combustible materials.
F. Combustible Materials Specification
Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite
and burn, whether flame proofed or not, or plastered or
unplastered shall be considered combustible materials.
G. Electrical Codes
NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA
70-latest edition or the Canadian Electric Code CSA
C22.1.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in compliance
with the applicable electrical codes, when it is installed in
locations such as in bathrooms or near sinks.
8
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
Note: The following requirements reference various
Massachusetts and national codes not contained in this
document.
H. Requirements for the Commonwealth of
Massachusetts
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7)
feet above finished grade in the area of the venting, including but not limited to decks and porches, the following
requirements shall be satisfied:
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fitter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that
a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of
the dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of
hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent
floor level.
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply
with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA
720 and be ANSI/UL 2034 listed and IAS certified.
Signage
A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read,
in print size no less than one-half (1/2) in. in size, “GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
Inspection
The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed
in accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
Exemptions
The following equipment is exempt from 248 CMR
5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment
Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate
from the dwelling, building or structure used in whole or
in part for residential purposes.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components; and
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
“special venting systems”, the following requirements
shall be satisfied by the manufacturer:
• The referenced “special venting system” instructions
shall be included with the appliance or equipment installation instructions; and
• The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation
instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall
remain with the appliance or equipment at the completion
of the installation.
See Gas Connection section for additional Commonwealth of Massachusetts requirements.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
9
2
Operating Instructions
User Guide
A. Gas Fireplace Safety
WARNING! DO NOT operate fireplace before reading
and understanding operating instructions. Failure
to operate fireplace according to operating instructions
could cause fire or injury.
WARNING
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
• Keep children away.
• CAREFULLY SUPERVISE children in same room
as fireplace.
• Alert children and adults to hazards of high
temperatures.
High temperatures may ignite clothing or other
flammable materials.
• Clothing, furniture, draperies, and other flammable
materials must not be placed on or near the
appliance.
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and
shall be installed. DO NOT operate the appliance with
the barrier removed. If the barrier becomes damaged,
the barrier shall be replaced with the manufacturer’s
barrier for this appliance.
• Consider not using the fireplace when children will be
present.
Contact your dealer for more information, or visit: www.
hpba.org/safety-information.
To prevent unintended operation when not using your fireplace for an extended period of time (summer months,
vacations, trips, etc):
• Remove batteries from remote controls.
• Turn off wall controls.
• Unplug 6 volt transformer plug and remove batteries on
IPI models.
• Turn off gas controls valve on standing pilot models.
When lighting the pilot light on fireplaces with a standing
pilot, remove the fixed glass assembly so you can detect presence of residual gas build-up. See Standing Pilot
Lighting instructions and Maintenance Tasks.
B. Your Fireplace
WARNING! DO NOT operate fireplace before reading and understanding operating instructions. Failure
to operate fireplace according to operating instructions
could cause fire or injury.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
Young children should be carefully supervised when they
are in the same room as the appliance. Toddlers, young
children and others may be susceptible to accidental
contact burns.
DECORATIVE DOORS
(NOT SHOWN)
SECTION 2.E.
FIXED GLASS ASSEMBLY
(NOT SHOWN)
SECTION 14.H.
• A physical barrier is recommended if there are at risk
individuals in the house.
• To restrict access to a fireplace or stove, install an
adjustable safety gate to keep toddlers, young children
and other at risk individuals out of the room and away
from hot surfaces.
• Install a switch lock or a wall/remote control with child
protection lockout feature.
MANTEL
SECTION 5.D
FAN KIT
SECTION 2.C.
HEARTH
CLEAR SPACE
SECTION 2.D.
• Keep remote controls out of reach of children.
• Never leave children alone near a hot fireplace, whether
operating or cooling down.
• Teach children to NEVER touch the fireplace.
10
GRATE
SECTION 3.C.
Figure 2.1 General Operating Parts
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
C. Fan Kit (optional)
If desired, a fan kit may be added. Contact your dealer to
order the correct fan kit.
D. Clear Space
WARNING! DO NOT place combustible objects in front
of the fireplace or block louvers. High temperatures may
start a fire. See Figure 2.2.
Avoid placing candles and other heat-sensitive objects on
mantel or hearth. Heat may damage these objects.
G. Remote Controls, Wall Controls and Wall
Switches
Follow the instructions supplied with the control installed
to operate your fireplace:
For safety:
• Install a switch lock or a wall/remote control with child
protection lockout feature.
• Keep remote controls out of reach of children.
See your dealer if you have questions.
3F
T.
IN CLE
FR AR
ON S
T O PAC
FF E
IR
EP
LA
CE
Figure 2.2 Clear Space
E. Decorative Doors and Fronts
WARNING! Risk of Fire! Install ONLY doors or fronts
approved by Hearth & Home Technologies. Unapproved
doors or fronts may cause fireplace to overheat.
This fireplace has been supplied with an integral
barrier to prevent direct contact with the fixed glass
panel. DO NOT operate the fireplace with the barrier
removed.
Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
install one.
For more information refer to the instructions supplied with
your decorative door or front.
F. Fixed Glass Assembly
See Section 14.H.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
11
H. IPI Battery Tray/Battery Installation
MODULE
The IntelliFire PlusTM system has a battery backup option.
Battery longevity and performance will be affected by the
service temperatures of this appliance.
NOTICE: Batteries should only be used as a power source
in the event of an emergency such as an outage.
SELECTOR
SWITCH
I. Control Module Operation
1.
The control module has an ON/OFF/REMOTE selector
switch that must be set. See Figure 2.3.
OFF Position: Appliance will ignore all power
inputs and will not respond to any commands from
a wall switch or remote. The unit should be in the
OFF position during installation, service, battery
installation, and in the event that the control goes
into LOCK-OUT mode as a result of an error code.
ON Position: Appliance will ignite and run
continuously in the HI flame setting, with no
adjustment in flame output. This mode of operation
is primarily used for initial installation or power
outage operation with battery backup.
3.
4.
Locate the module selector switch. (SeeFigure 2.3).
•
Set the module selector switch to the OFF position.
•
Wait five (5) minutes to allow possible accumulated gas
to clear.
•
Set the module selector switch to the ON or REMOTE
position.
If using a wired wall switch with the module in REMOTE
mode, the flame output can be adjusted with the HI/
LO selector switch on the module. See Figure 2.3.
Note that the flame HI/LO selector switch will become
inactive once an optional remote control (RC200/
RC300) is programmed to the control module. Note
that the control module will always ignite the fireplace
on HI and remain so for the initial 10 seconds of
operation. If the HI/LO is switched to the LO position,
the flame output will automatically drop to the lowest
setting after the flame has been established for 10 sec.
After this 10 second period, the flame can be adjusted
from HI to LO with the switch.
•
Start the appliance.
The control module has safety feature that automatically
shuts down the fireplace after 9 hours of continuous
operation without receiving a command from the
remote.
J. Before Lighting Fireplace
If you intend to use both a wired wall switch and the
RC300 remote control to operate your fireplace, the
wall switch will override any commands given by the
remote.
5. Module Reset
This module may lock-out under certain conditions.
When this occurs, the appliance will not ignite or
respond to commands. The module will go into
lock-out mode by emitting three audible beeps, then
continuously displaying a RED/GREEN error code at
its status indicator LED.
•
12
Figure 2.3 Control Module
•
REMOTE Position:
Appliance will initiate
commands from an optional wired wall switch and/
or the wireless remote (RC300).
2.
FLAME HI/LOW SWITCH
NG/LP GAS-TYPE
STATUS
(RC100 OR WIRED
INDICATOR LED SELECTOR SWITCH
WALLSWITCH ONLY)
Check battery tray. Remove batteries if installed.
Batteries should only be installed for use during power
outages. See Section H.
WARNING! Risk of Explosion! DO NOT reset the module more than one time within a five minute time period.
Gas may accumulate in firebox. Call a qualified service
technician.
Nine Hour Safety Shutdown Feature
This appliance has a safety feature that automatically
shuts down the fireplace after 9 hours of continuous
operation without receiving a command from the
remote.
Before operating this fireplace for the first time, have a
qualified service technician:
• Verify all shipping materials have been removed from
inside and/or underneath the firebox.
• Review proper placement of logs, ember material and/
or other decorative materials.
• Ensure plastic finishing strips have been removed after
use for incorporating finishing materials.
• Check the wiring.
• Check the air shutter adjustment.
• Ensure that there are no gas leaks.
• Ensure that the glass is sealed and in the proper position
and that the integral barrier is in place.
WARNING! Risk of Fire or Asphyxiation! DO NOT operate fireplace with fixed glass assembly removed.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
K. Lighting Instructions (IPI)
FOR YOUR SAFETY
READ BEFORE LIGHTING
LIGHTING
INSTRUCTIONS (IPI)
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
1. This appliance is equipped with an ignition
device which automatically lights the burner.
DO NOT try to light the burner by hand.
A. This appliance is equipped with an
intermittent pilot ignition (IPI) device
which automatically lights the burner. DO NOT try to light the burner by
hand.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
B. BEFORE LIGHTING, smell all around
the appliance area for gas. Be sure to
smell next to the floor because some
gas is heavier than air and will settle
on the floor.
C. DO NOT use this appliance if any
part has been under water. Immediately call a qualified service technician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• If you cannot reach your gas supplier, call the fire department.
• DO NOT touch any electric switch; do
not use any phone in your building.
CAUTION:
DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240
VAC) TO THE CONTROL VALVE.
Hot while in operation. DO NOT touch.
Keep children, clothing, furniture, gasoline and other liquids having flammable
vapors away.
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could
expose you to substances in fuel or
fuel combustion which are known to the
State of California to cause cancer, birth
defects, or other reproductive harm.
Keep burner and control compartment
clean. See installation and operating
instructions accompanying appliance.
2. Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the floor. If
you smell gas, STOP! Follow “B” in the Safety
Information located on the left side of this label. If you do not smell gas, go to next step.
3. To light the burner:
Equipped with wall switch: Turn ON/OFF switch
to ON.
WARNING:
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Refer to the owner’s information manual
provided with this appliance.
GAS
VALVE
DO NOT operate the appliance with
fixed glass assembly removed, cracked
or broken. Replacement of the fixed
glass assembly should be done by a
licensed or qualified service person.
NOT FOR USE
WITH SOLID FUEL
For use with natural gas and propane.
A conversion kit, as supplied by the
manufacturer, shall be used to convert
this appliance to the alternate fuel.
Equipped with remote or wall control: Press
ON or FLAME button.
Equipped with thermostat: Set temperature to
desired setting.
4. If the appliance does not light after three tries,
call your service technician or gas supplier.
TO TURN OFF
GAS TO APPLIANCE
1. Equipped with wall switch: Turn ON/OFF switch
to OFF.
Equipped with remote or wall control: Press
OFF button.
Equipped with thermostat: Set temperature to
lowest setting.
2. Service technician should turn off electric
power to the control when performing service.
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
593-913G
For assistance or additional information, consult a qualified installer, service agency or the gas supplier.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
Final inspection by
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
13
L. Lighting Instructions (Standing Pilot)
FOR YOUR SAFETY
READ BEFORE LIGHTING
LIGHTING
INSTRUCTIONS
1. Open control access panel.
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This appliance has a pilot which
must be lighted by hand. When
lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING, smell all around
the appliance area for gas. Be sure to
smell next to the floor because some
gas is heavier than air and will settle
on the floor.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or
turn the gas control knob. Never use
tools. If the knob will not push in or
turn by hand, DO NOT try to repair
it, call a qualified service technician.
Force or attempted repair may result in a fire or explosion.
D. DO NOT use this appliance if any
part has been under water. Immediately call a qualified service technician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.
WARNING:
CAUTION:
DO NOT CONNECT 110 VAC TO
THE CONTROL VALVE.
Hot while in operation. DO NOT touch.
Keep children, clothing, furniture, gasoline and other liquids having flammable
vapors away.
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Refer to the owner’s information manual
provided with this appliance.
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product
could expose you to substances in fuel
or fuel combustion which are known to
the State of California to cause cancer, birth defects, or other reproductive
harm.
Keep burner and control compartment
clean. See installation and operating
instructions accompanying appliance.
DO NOT operate the appliance with
fixed glass assembly removed, cracked
or broken. Replacement of the fixed
glass assembly should be done by a
licensed or qualified service person.
NOT FOR USE
WITH SOLID FUEL
For use with natural gas and propane.
A conversion kit, as supplied by the
manufacturer, shall be used to convert
this appliance to the alternate fuel.
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
For assistance or additional information, consult a qualified installer, service agency or the gas supplier.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
2. Turn off all electric power to
the appliance.
3. Push in gas control knob
slightly and turn clockwise
to “OFF”.
Note: Knob cannot be turned from “PILOT” to “OFF”
unless knob is pushed in slightly. DO NOT force.
4. Open the fixed glass assembly. You may need to
remove the decorative front.
5. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you smell
gas, STOP! Follow “B” in the Safety
Information located on the left side
of this label. If you don’t smell gas,
go to next step.
6. Find the pilot. The pilot is inside
combustion chamber next to the
main burner
7. Turn knob on gas control counterclockwise
to “PILOT”.
8. Push in control knob all the way and hold in. Immediately depress red or black piezo button. It may require
several depressions of the red or black piezo button
until PILOT lights. If PILOT light does not light after
10 seconds, return to step 3. Continue to hold the
control knob in for about one minute after the pilot is
lit. Release knob and it will pop back out. Pilot should
remain lit. If it goes out, repeat steps 3 through 6.
• If knob does not pop up when released, stop and
immediately call your service technician or gas
supplier.
• If the pilot will not stay lit after several tries, turn
the gas control knob to “OFF” and call your service technician or gas supplier.
9. Reinstall fixed glass assembly. Reinstall decorative
front.
10. Turn gas control knob counterclockwise
to “ON”. Close access panel.
11. Turn on all electric power to the appliance.
12. To light burner, turn the wall control or on/off switch
to “ON”.
TO TURN OFF
GAS TO APPLIANCE
1. Turn off all electric power to the appliance if service is to be performed.
2. Open control access panel.
3. Move switch to “OFF” position.
4. Push in gas control knob slightly and turn clockwise
to OFF”. DO NOT force.
5. Close control access panel.
Final inspection by
14
464-903H
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
M. After Fireplace is Lit
Initial Break-in Procedure
• The fireplace should be run three to four hours
continuously on high.
• Turn the fireplace off and allow it to completely cool.
• Remove fixed glass assembly. See Section 14.H.
• Clean fixed glass assembly. See Section 3.
• Replace the fixed glass assembly and run continuously
on high an additional 12 hours.
This cures the materials used to manufacture the fireplace.
NOTICE! Open windows for air circulation during fireplace break-in.
• Some people may be sensitive to smoke and odors.
• Smoke detectors may activate.
N. Frequently Asked Questions
ISSUE
SOLUTIONS
Condensation on the glass
This is a result of gas combustion and temperature variations. As the appliance warms, this
condensation will disappear.
Blue flames
This is a result of normal operation and the flames will begin to yellow as the appliance is allowed to burn for 20 to 40 minutes.
Odor from appliance
When first operated, this appliance may release an odor for the first several hours. This is caused
by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may
also be released from finishing materials and adhesives used around the appliance.
This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See
your dealer.
Film on the glass
Metallic noise
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Is it normal to see the pilot flame burn
continually?
In an intermittent pilot ignition system (IPI), the pilot flame should turn off when appliance is
turned off. Some optional control systems available with IPI models may allow pilot flame to
remain lit. In a standing pilot system the pilot will always stay on.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
15
3
Maintenance and Service
Any safety screen or guard removed for servicing must be
replaced prior to operating the fireplace.
Doors, Surrounds, Fronts
Frequency: Annually
When properly maintained, your fireplace will give you
many years of trouble-free service. We recommend annual service by a qualified service technician.
By: Homeowner
A. Maintenance Tasks-Homeowner
• Inspect for scratches, dents or other damage and repair
as necessary.
Installation and repair should be done by a qualified service
technician only. The fireplace should be inspected before
use and at least annually by a professional service person.
The following tasks may be performed annually by the
homeowner. If you are uncomfortable performing any of
the listed tasks, please call your dealer for a service appointment.
More frequent cleaning may be required due to lint from
carpeting or other factors. Control compartment, burner
and circulating air passageway of the fireplace must be
kept clean.
CAUTION! Risk of Burns! The fireplace should be turned
off and cooled before servicing.
Glass Cleaning
Tools needed: Protective gloves, stable work surface
• Assess condition of screen and replace as necessary.
• Check that louvers are not blocked.
• Vacuum and dust surfaces.
Remote Control
Frequency: Seasonally
By: Homeowner
Tools needed: Replacement batteries and remote control instructions.
• Locate remote control transmitter and receiver.
• Verify operation of remote. Refer to remote control
operation instructions for proper calibration and setup
procedure.
Frequency: Seasonally
• Place batteries as needed in remote transmitters and
battery-powered receivers.
By: Homeowner
• Place remote control out of reach of children.
Tools Needed: Protective gloves, glass cleaner, drop
cloth and a stable work surface.
If not using your fireplace for an extended period of time
(summer months, vacations/trips, etc), to prevent unintended operation:
CAUTION! Handle fixed glass assembly with care.
Glass is breakable.
• Avoid striking, scratching or slamming glass
• Avoid abrasive cleaners
• DO NOT clean glass while it is hot
• Prepare a work area large enough to accommodate fixed
glass assembly and door frame by placing a drop cloth
on a flat, stable surface.
• Remove batteries from remote controls.
• Unplug 6 volt transformer plug on IPI models.
• Unplug battery backup from control module.
Note: Fixed glass assembly and gasketing may have residue that can stain carpeting or floor surfaces.
• Remove door or decorative front from fireplace and set
aside on work surface.
• See Section 14.H for instructions to remove fixed glass
assembly.
• Clean glass with a non-abrasive commercially available
cleaner.
- Light deposits: Use a soft cloth with soap and water
- Heavy deposits: Use commercial fireplace glass
cleaner (consult with your dealer)
• Carefully set fixed glass assembly in place on fireplace.
Hold glass in place with one hand and secure glass
latches with the other hand.
• Reinstall door or decorative front.
16
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
Venting
• Replace fireplace if firebox has been perforated.
Frequency: Seasonally
Control Compartment and Firebox Top
By: Homeowner
Frequency: Annually
Tools needed: Protective gloves and safety glasses.
By: Qualified Service Technician
• Inspect venting and termination cap for blockage or
obstruction such plants, bird nests, leaves, snow, debris,
etc.
Tools needed: Protective gloves, vacuum cleaner, dust
cloths
• Verify termination cap clearance to subsequent construction (building additions, decks, fences, or sheds). See
Section 6.
• Vacuum and wipe out dust, cobwebs, debris or pet hair.
Use caution when cleaning these areas. Screw tips that
have penetrated the sheet metal are sharp and should
be avoided.
• Inspect for corrosion or separation.
• Remove all foreign objects.
• Verify weather stripping, sealing and flashing remains
intact.
• Verify unobstructed air circulation.
• Inspect draft shield to verify it is not damaged or missing.
B. Maintenance Tasks-Qualified Service
Technician
The following tasks must be performed by a qualified service technician.
Gasket Seal and Glass Assembly Inspection
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, drop cloth and a stable
work surface.
• Inspect gasket seal and its condition.
• Inspect fixed glass assembly for scratches and nicks that
can lead to breakage when exposed to heat.
• Confirm there is no damage to glass or glass frame.
Replace as necessary.
• Verify that fixed glass assembly is properly retained and
attachment components are intact and not damaged.
Replace as necessary.
Logs
Frequency: Annually
Burner Ignition and Operation
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, vacuum cleaner, whisk
broom, flashlight, voltmeter, indexed drill bit set, and a
manometer.
• Verify burner is properly secured and aligned with pilot
or igniter.
• Clean off burner top, inspect for plugged ports, corrosion
or deterioration. Replace burner if necessary.
• Replace Glowing embers with new dime-size pieces.
DO NOT block ports or obstruct lighting paths. Refer to
Section 14 for proper ember placement.
• Verify batteries have been removed from battery backup IPI systems to prevent premature battery failure or
leaking.
• Check for smooth lighting and ignition carryover to all
ports. Verify that there is no ignition delay.
• Inspect for lifting or other flame problems.
• Verify air shutter setting is correct. See Section 14 for
required air shutter setting. Verify air shutter is clear of
dust and debris.
Tools needed: Protective gloves.
• Inspect orifice for soot, dirt and corrosion. Verify orifice
size is correct. See Service Parts List for proper orifice
sizing.
• Inspect for damaged or missing logs. Replace as necessary. Refer to Section 14 for log placement instructions.
• Verify manifold and inlet pressures. Adjust regulator as
required.
• Verify correct log placement and no flame impingement
causing sooting. Correct as necessary.
• Inspect pilot flame pattern and strength. See Figures 3.1
and 3.2 for proper pilot flame pattern. Clean or replace
orifice spud as necessary.
By: Qualified Service Technician
Firebox
By: Qualified Service Technician
• Inspect thermocouple/thermopile or IPI flame sensing
rod for soot, corrosion and deterioration. Polish with fine
steel wool or replace as required.
Tools needed: Protective gloves, sandpaper, steel wool,
cloths, mineral spirits, primer and touch-up paint.
• Verify thermocouple/thermopile millivolt output. Replace
pilot as necessary. (Standing pilot only)
• Inspect for paint condition, warped surfaces, corrosion
or perforation. Sand and repaint as necessary.
• Verify that there is not a short in flame sense circuit
by checking continuity between pilot hood and flame
sensing rod. Replace pilot as necessary. (IPI only)
Frequency: Annually
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
17
Figure 3.1 IPI Pilot Flame Patterns
Figure 3.3 Grate Removal
Note: The base refractory must be
removed to access screws.
BASE REFRACTORY
Figure 3.2 Standing Pilot Flame Patterns
C. Refractory, Grate and Valve Assembly
Removal
It may become necessary to remove the refractory, grate
and valve assemblies. This task should be performed by
a qualified service technician. The grate and base refractory do not need to be removed to service the burner
assembly.
Figure 3.4 Base Refractory Removal
18
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
Figure 3.5 Valve Assembly Removal
D. Burner Identification/Verification
The burner may be accessed for identification and verification purposes. This task should be performed by a qualified service technician. The base refractory, valve plate and grate do not need to be removed to access the burner assembly. The
logs and fiber burner top need to be removed to access the burner. Disconnect the pilot from the burner before removal.
See Figure 3.6 for burner identification chart. Notch patterns are located on bottom side of burner.
NOTCH LOCATION
NG
LP
6000C
6000CL
6000CLX
6000CBV
8000C
8000CL
8000CLX
8000CBV
Figure 3.6 Burner Identification
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
19
4
Getting Started
Installer Guide
A. Typical Appliance System
NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not
drawn to scale. Actual product may vary from pictures in manual
HORIZONTAL
TERMINATION CAP
(SECTION 10.L)
Note: Dual venting configurations
ARE NOT allowed. Appliance MUST
be vented EITHER ver tically OR
horizontally.
VERTICAL TERMINATION CAP
(SECTION 10.I)
NON-COMBUSTIBLE ROOF FLASHING
MAINTAINS MINIMUM CLEARANCE
AROUND PIPE (SECTION 10.G)
STORM COLLAR
(SECTION 10.H)
VENT PIPE PENETRATES ROOF
PREFERABLY WITHOUT AFFECTING
ROOF RAFTERS (SECTION 8.C)
VENT PIPE (SECTIONS 7 and 8)
ATTIC INSULATION SHIELD (NOT
SHOWN) MUST BE USED HERE TO
KEEP INSULATION AWAY FROM
VENT PIPE IF ATTIC IS INSULATED
(SECTION 8.D)
CEILING FIRESTOP
ON FLOOR OF ATTIC
(SECTION 8.C)
FRAMING/HEADER
(SECTION 5.B)
FRAMING HEADED OFF
IN CEILING JOISTS
(SECTION 8.C)
OPTIONAL
WALL SWITCH
MANTEL AND
MANTEL LEG
(SECTION 5.D)
SURROUND
HEARTH EXTENSION
GAS LINE
(SECTION 11)
Figure 4.1 Typical System
20
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
B. Design and Installation Considerations
D. Inspect Appliance and Components
Heat & Glo direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
the building and all exhaust gases expelled to the outside.
No additional outside air source is required.
• Carefully remove the appliance and components from
the packaging.
Installation MUST comply with local, regional, state and
national codes and regulations. Consult insurance carrier,
local building inspector, fire officials or authorities having
jurisdiction over restrictions, installation inspection and
permits.
• If packaged separately, the log set and appliance grate
must be installed.
Before installing, determine the following:
• Read all of the instructions before starting the installation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
• Where the appliance is to be installed.
• The vent system configuration to be used.
• Gas supply piping requirements.
• Electrical wiring requirements.
• The vent system components and decorative doors and
fronts may be shipped in separate packages.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.
• Framing and finishing details.
• Whether optional accessories—devices such as a fan,
wall switch, or remote control—are desired.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a qualified
service technician, service agency or your dealer.
Hearth & Home Technologies disclaims any responsibility for,
and the warranty will be voided by, the following actions:
• Installation and use of any damaged appliance or vent
system component.
• Modification of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass door.
C. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
Tape measure
Framing material
Pliers
Non-corrosive leak check solutionHammer
Phillips screwdriver
Gloves
Framing square
Voltmeter
Electric drill and bits (1/4 in.)
Plumb line
Safety glasses
Level
Reciprocating saw
Manometer
Flat blade screwdriver
1/2 - 3/4 in. length, #6 or #8 Self-drilling screws
Caulking material (300ºF minimum continuous exposure
rating)
One 1/4 in. female connection (for optional fan).
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fire hazard.
WARNING! Risk of Fire, Explosion or Electric Shock!
DO NOT use this appliance if any part has been under
water. Call a qualified service technician to inspect the
appliance and to replace any part of the control system
and/or gas control which has been under water.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
21
5
Framing and Clearances
A. Selecting Appliance Location
NOTICE: Illustrations reflect typical installations and are
FOR DESIGN PURPOSES ONLY. Illustrations/diagrams
are not drawn to scale. Actual installation may vary due to
individual design preference.
When selecting a location for the appliance it is important to
consider the required clearances to walls (see Figure 5.1).
WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
NOTE: THE REAR STANDOFF MAY NEED
TO BE REMOVED WHEN VENTING AT 45º
A
G
1/2 IN.
B
ALCOVE
INSTALLATION
A
B
E
C
TOP VENT
ONE 90º ELBOW
REAR VENT,
HORIZONTAL TERMINATION
TWO ELBOWS
B
D
REAR VENT
ONE ELBOW
REAR VENT
NO ELBOWS
B
B
D
F
D
H
6000
8000
D
A
B
C
D
51
42
72
56-5/8
mm
1295
1067
1829
1438
in.
55-7/8
49
79
61-1/2
mm
1419
1245
2007
1562
in.
E
F
G
H
See Section D.
Mantel Projections
22
17-3/4
8
559
451
203
22
19-3/4
10
559
502
254
See Section D.
Mantel Projections
Figure 5.1 Appliance Locations - 6000 Models
22
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
B. Constructing the Appliance Chase
stops should be caulked with caulk with a minimum of
300ºF continuous exposure rating to seal gaps. Gas line
holes and other openings should be caulked with caulk
with a minimum of 300ºF continuous exposure rating or
stuffed with unfaced insulation. If the appliance is being
installed on a cement surface, a layer of plywood may be
placed underneath to prevent conducting cold up into the
room.
A chase is a vertical box-like structure built to enclose the
gas appliance and/or its vent system. In cooler climates
the vent should be enclosed inside the chase.
NOTICE: Treatment of ceiling firestops and wall shield
firestops and construction of the chase may vary with the
type of building. These instructions are not substitutes
for the requirements of local building codes. Therefore,
you MUST check local building codes to determine the
requirements to these steps.
C. Clearances
NOTICE: Install appliance on hard metal or wood surfaces
extending full width and depth. DO NOT install directly
on carpeting, vinyl, tile or any combustible material other
than wood.
Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building
envelope in any manner.
WARNING! Risk of Fire! Maintain specified air space
clearances to appliance and vent pipe:
Walls, ceiling, base plate and cantilever floor of the chase
should be insulated. Vapor and air infiltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infiltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.
• Insulation and other materials must be secured to prevent
accidental contact.
• The chase must be properly blocked to prevent blown
insulation or other combustibles from entering and
making contact with fireplace or chimney.
To further prevent drafts, the wall shield and ceiling fire-
• Failure to maintain airspace may cause overheating and
a fire.
A
E
B
J
F
H
C
D
I
G
* MINIMUM FRAMING DIMENSIONS
Models
6000
8000
A
B
C**
Rough
Opening
(Width)
Rough
Opening
(Height)
Rough
Opening
(Depth)
D
E
F
G
H
I
J
Rough
Clearance Combustible Combustible Behind
Sides of
Front of
Opening
to Ceiling
Floor
Flooring
Appliance Appliance Appliance
(Width)
in.
10
40-1/8
22
42
25
0
0
1/2
1/2
36
mm
254
1019
559
1067
635
0
0
13
13
914
in.
10
42-1/8
22
49
25
0
0
1/2
1/2
36
mm
254
1019
559
1245
635
0
0
13
13
914
* Adjust framing dimensions for interior sheathing (such as sheetrock)
C** Add 12 inches for rear venting with one 90º elbow.
Figure 5.2 Clearances to Combustibles
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
23
D. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing or finishing material closer than
the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).
Mantel Legs or Wall Projections - Combustible or
Painted Surfaces
INTERIOR WALL
Mantels - Combustible or Painted Surfaces
TOP VIEW
TO CEILING
18
A
12
B
11
10
32
9
25
8
7
19
6
5
3
17
4
18
16
15
14
13
12
2-1/2
FIREPLACE OPENING
11
10
5
MANTEL LEG OR WALL PROJECTIONS
If
A
B
A minimum is ____, then B maximum is_____.
Inches
2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16
Inches
62
1
87
2
113
3
138
4
164
5
Millimeters
25
51
76
102
127
Millimeters


Figure 5.4 Clearances to Mantel Legs or Wall Projections
(Acceptable on both sides of opening.)
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
Note: All measurements in inches.
Note: Measurement is taken from top of the
opening, NOT the top of the fireplace.
Figure 5.3 Minimum Vertical and Maximum Horizontal
Dimensions
24
189
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
6
Termination Locations
A. Vent Termination Minimum Clearances
WARNING
A
B
6 in. (minimum) up to 20 in.
152 mm/508 mm
18 in. minimum
457 mm
20 in. and over
0 in. minimum
Fire Risk.
Maintain vent clearance to combustibles as
specified.
• DO NOT pack air space with insulation or other
materials.
Failure to keep insulation or other materials away
from vent pipe may cause overheating and fire.
Gas, Wood or Fuel Oil
Termination Cap
B
A*
HORIZONTAL
OVERHANG
2 FT.
MIN.
20 INCHES MIN.
Gas
Termination
Cap **
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
GAS DIRECT VENT
TERMINATION CAP
X
12
*
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
**
If using decorative cap cover(s), this distance may need to be
increased. Refer to the installation instructions supplied with the
decorative cap cover.
In a staggered installation with both gas and wood or fuel oil
terminations, the wood or fuel oil termination cap must be
higher than the gas termination cap.
Figure 6.2 Staggered Termination Caps
Roof Pitch
H (Min.) Ft.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12 .................................................1.25*
Over 7/12 to 8/12 .................................................1.5*
Over 8/12 to 9/12 .................................................2.0*
Over 9/12 to 10/12 ...............................................2.5*
Over 10/12 to 11/12 .............................................3.25
Over 11/12 to 12/12 .............................................4.0
Over 12/12 to 14/12 .............................................5.0
Over 14/12 to 16/12 .............................................6.0
Over 16/12 to 18/12 .............................................7.0
Over 18/12 to 20/12 .............................................7.5
Over 20/12 to 21/12 .............................................8.0
* 3 foot minimum in snow regions
Figure 6.1 Minimum Height From Roof To Lowest Discharge
Opening
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
25
O
N
P
R
F
C
Q
V
B
J
H or i
B
V
D
V
B
V
V
H
V
X
G
M
V
A
V
E
H
V
V
V
L
A
V
V = VENT TERMINAL
X = AIR SUPPLY INLET
K
B
C
= 9 inches...................clearance to outside corner
E
= 6 inches...................clearance to inside corner
Covered Alcove Applications
(Spaces open only on one side and with an overhang)
N
O
L
= 12 inches................clearance above electrical service
= 18 inches ......... non-vinyl soffit and overhang
42 inches ......... vinyl soffit and overhang
P
= 3 ft. (Canada) ..........not to be installed above a gas meter/regulator assembly within 3 feet
horizontally from the center-line of the
regulator
G = 3 ft ...........................clearance to gas service regulator
vent outlet
H
= 9 inches (U.S.A)
12 inches (Canada) .clearance to non-mechanical (unpowered) air supply inlet, combustion air
inlet or direct-vent termination
i
= 3 ft. (U.S.A.)
6 ft. (Canada) ...........clearance to a mechanical (powered)
air supply inlet
All mechanical air intakes within 10 feet of a termination cap
must be a minimum of 3 feet below termination.
J
= 7 ft. ......................... On public property: clearance above
paved sidewalk or a paved driveway.
A vent shall not terminate directly above a sidewalk or paved
driveway which is located between two single family dwellings
and serves both dwellings.
= 6 inches.................clearance from sides of electrical
service
= 6 inches ........... non-vinyl sidewalls
12 inches ......... vinyl sidewalls
F
K
V
V
= 12 inches.................clearances above grade, veranda,
porch, deck or balcony
= 12 inches.................clearance to window or door that may
be opened, or to permanently closed
window
= 18 inches.................clearance below unventilated soffit
18 inches.................clearance below ventilated soffit
30 inches ................clearance below vinyl soffits and
electrical service
D
K
C
= AREA WHERE TERMINAL IS NOT PERMITTED
A
Electrical
Service
= 8 ft.
QMIN
RMAX
1 cap
3 feet
2 x Q ACTUAL
2 caps
6 feet
1 x Q ACTUAL
3 caps
9 feet
2/3 x Q ACTUAL
4 caps
12 feet
1/2 x Q ACTUAL
QMIN = # termination caps x 3
RMAX = (2 / # termination caps) x QACTUAL
Measure vertical clearances from this surface.
Measure horizontal clearances from this surface.
CAUTION! Risk of Burns! Termination caps are HOT,
consider proximity to doors, traffic areas or where people
may pass or gather (sidewalk, deck, patio, etc.). Listed cap
shields available. Contact your dealer.
•
Local codes or regulations may require different
clearances.
•
Vent system termination is NOT permitted in screened
porches.
= 18 inches ....................clearance under veranda, porch, deck,
balcony or overhang
42 inches ................vinyl or composite overhang
Permitted when veranda, porch, deck or balcony is fully open
on a minimum of 2 sides beneath the floor.
•
Vent system termination is permitted in porch areas with
two or more sides open.
•
Figure 6.3 Minimum Clearances for Termination
•
Hearth & Home Technologies assumes no responsibility
for the improper performance of the appliance when the
venting system does not meet these requirements.
Vinyl protection kits are suggested for use with vinyl siding.
Location of the vent termination must not interfere with access to the
electrical service.
M
26
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
7
Vent Information and Diagrams
A. Approved Pipe
DO NOT mix pipe, fittings or joining methods from different manufacturers.
Vertical
12
in
.
The pipe is tested to be run inside an enclosed wall.
There is no requirement for inspection openings at each
joint within the wall.
8-1/2 in.
WARNING! Risk of Fire or Asphyxiation. This appliance requires a separate vent. DO NOT vent to a pipe
serving a separate solid fuel burning appliance.
B. Vent Table Key
Horizontal
The abbreviations listed in this vent table key are used in
the vent diagrams.
Symbol
8-1/2 in.
This appliance is approved for use with Hearth & Home
Technologies DVP or SLP venting systems. Refer to Section 16B for vent component information.
Figure 7.1
Description
V1
First section (closest to appliance) of vertical length
V2
Second section of vertical length
H1
First section (closest to appliance) of horizontal length
H2
Subsequent sections of horizontal length
C. Use of Elbows
Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect (see
Figure 7.1).
D. Measuring Standards
Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards.
• Pipe measurements are shown using the effective length
of pipe (see Figure 7.2).
• Horizontal terminations are measured to the outside
mounting surface (flange of termination cap) (see Figure
6.3).
• Vertical terminations are measured to bottom of
termination cap.
• Horizontal pipe installed level with no rise.
Two 45º elbows may be used in place of one 90º elbow.
On 45º runs, one foot of diagonal is equal to 8-1/2 in. (216
mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A
length of straight pipe is allowed between two 45º elbows
(see Figure 7.1).
Pipe
DVP4
Effective
Height/Length
Effective Length
Inches
Millimeters
4
102
DVP6
6
152
DVP12
12
305
DVP24
24
610
DVP36
36
914
DVP48
48
1219
DVP6A
3 to 6
76 to 152
DVP12A
3 to 12
76 to 305
Figure 7.2 DVP Pipe Effective Length
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
27
E. Vent Diagrams
Top Vent - Horizontal Termination
WARNING
Note: The 6000/8000 series fireplaces can adapt to SLP series
vent pipe, if desired.
Fire Risk. Explosion Risk.
Do NOT pack insulation or other combustibles
between ceiling firestops.
• ALWAYS maintain specified clearances around
venting and firestop systems.
• Install wall shield and ceiling firestops as specified.
Failure to keep insulation or other material away
from vent pipe may cause fire.
When venting off the top of the unit, use a DVP-2SL adapter and a
minimum 48 inch vertical section of SLP series vent pipe.
A DVP-SLP24 adapter may also be used with a 24 inch vertical
section of SLP series vent pipe.
After the 48 inch vertical section, the venting table rules must be
followed. The first 48 inch vertical section is NOT counted as part
of the vertical components in the table. It is still counted as part of
the overall maximum run. All venting table rules for the vent run
must still be followed.
WARNING
Example: DVP pipe 3 ft. min. vertical = 11 ft. max. horizontal
SLP pipe 7 ft. min. vertical = 11 ft. max. horizontal
Fire Risk.
• When using DVP-HRC-SS and DVP-HRC-ZCSS termination caps on top vented fireplaces, a
6 inch minimum vertical vent section is required
before installing first elbow.
Top Vent - Horizontal Termination
One Elbow
6000C-IPI
V1 Minimum
H1 Maximum
Elbow only
6 in.
8000C-IPI
152 mm
V1 Minimum
2 ft
610 mm
Elbow Only
4 ft.
1.2 m
1 ft.
305 mm
H1 Maximum
2 ft.
610 mm
3 ft.
914 mm
1 ft.
305 mm
6 ft.
1.8 m
2 ft.
610 mm
6 ft.
1.8 m
1-1/2 ft.
457 mm
10 ft.
3.0 m
3 ft.
914 mm
11 ft.
3.4 m
2 ft.
610 m
15 ft.
4.6 m
4 ft.
1.2 m
20 ft.
6.1 m
2-1/2 ft.
762 mm
20 ft.
6.1 m
3 ft.
914 mm
25 ft.
7.6 m
V1 + H1 = 40 ft. (12.2 m) Maximum
H1 = 20 ft. (6.1 m) Maximum
V1 + H1 = 40 ft. (12.2 m) Maximum
H1 = 25 ft. (7.6 m) Maximum
Note: For corner installations: A 6 inch (152
mm) section of straight pipe may need to
be attached to the appliance before a 90º
elbow, to allow the vent pipe to clear the top
standoffs.
V1
H1
Figure 7.3
28
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
Top Vent - Horizontal Termination - (continued)
Two Elbows
6000C-IPI
8000C-IPI
V1 Minimum
H1 + H2 Maximum
V1 Minimum
H1 + H2 Maximum
Elbow only
Not allowed
Elbow only
Not allowed
6 in.
152 mm
2 ft.
610 mm
6 in.
152 mm
1 ft.
305 mm
4 ft.
1.2 m
1 ft.
305 mm
2 ft.
Not allowed
610 mm
1-1/2 ft.
457 mm
11 ft.
3.4 m
2 ft.
610 mm
4 ft.
1.2 m
2 ft.
610 mm
19 ft.
3.8 m
3 ft.
914 mm
6 ft.
1.8 m
2-1/2 ft.
762 mm
22 ft.
6.7 m
4 ft.
1.2 m
8 ft.
2.4 m
V1 + H1 + H2 = 40 ft. (12.2 m) Maximum
H1 + H2 = 22 ft. (6.7 m) Maximum
V1 = 1 ft. (305 mm) Minimum
6 ft.
1.8 m
12 ft.
3.6 m
10 ft.
3.0
20 ft.
6.1 m
V1 + H1 + H2 = 40 ft. (12.2 m) Maximum
H1 + H2 = 20 ft. (6.0 m) Maximum
V1 = 1 ft. (305 mm) Minimum
Note: For corner installations: A 6 inch
(152 mm) section of straight pipe may
need to be attached to the appliance
before a 90º elbow, to allow the vent
pipe to clear the top standoffs.
V1
H2
H1
INSTALLED
HORIZONTALLY
Figure 7.4
Three Elbows
V1 Min.
Elbow only
H1 Max.
H2 Max.
2 ft.
610 mm
0 in.
0 mm
1 ft.
305 mm
6 in.
152 mm
3 ft
914 mm
6 in.
152 mm
2 ft.
610 mm
1 ft.
305 mm
6 ft.
1.8 m
1 ft.
305 mm
6 ft.
1.8 m
2 ft.
610 mm
11 ft.*
3.4 m*
2 ft.
610 mm
10 ft.*
3.1 m*
3 ft.
914 mm
16 ft *
4.9 m*
3 ft.
914 mm
14 ft.*
4.3 m*
*H1 + H2 = 20 ft. (6.1 m) Maximum
H2
V2 Min.
V1 + V2 + H1 + H2 = 40 ft. (12.2 m) Maximum
V2
H1
V1
Figure 7.5
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
29
Top Vent - Vertical Termination
Flue Restrictor Instructions
No Elbow
1. Remove exhaust shield using a 1/4 inch nut driver by
removing the four screws securing it in place (see Figure
7.7).
V1 = 40 ft. Max. (12.4 m)
V1 = 3 ft. Min. (914 mm)
Note: If installing a vertical vent/
termination off the top of the appliance, the flue restrictor should
be used.
EXHAUST
SHIELD
FLUE
RESTRICTOR
Figure 7.7
V1
2. Break the flue restrictor into two pieces. Do this by
bending the part back and forth until it breaks (see
Figure 7.8).
BREAK
HERE
Figure 7.8 Flue Restrictor
Figure 7.6
30
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
Top Vent - Vertical Termination (continued)
4. Center the Flue Restrictor on vent and secure in place
by using two self-tapping screws (see Figure 7.10).
3. Match the amount of vertical you have in the system
with the chart to find the appropriate position to set the
Flue Restrictor (see Figure 7.9).
5. Reinstall the Exhaust Shield.
Vertical
TOP VENT
NG
LP
REAR VENT
NG
LP
4 ft.
1-1
No
Restrictor
No
Restrictor
8 ft.
2-2
1-2
1-1
No
Restrictor
No
Restrictor
15 ft.
3-3
3-2
2-2
1-2
20 ft.
3-4
3-3
3-3
2-3
25 ft.
3-4
3-3
3-3
2-3
30 ft.
4-4
3-4
3-4
3-3
35 ft.
4-4
3-4
3-4
3-3
40 ft.
4-4
4-4
4-4
3-4
1
2
3
4 5
SETTING
1
2
3
4 5
Figure 7.10
Figure 7.9
Note: If the DVP-2SL or DVP-SLP24 adapter is used with
SLP pipe, you MUST subtract one number from the table
above.
Example: Top vent 40 ft vertical with DVP pipe = 4-4
Top vent 40 ft vertical with SLP pipe = 3-3
V1
Two Elbows
H1 Maximum
Elbow only
V2
V1 + V2 Min.
2 ft.
610 mm
*
*
*
6 in.
152 mm
6 ft.
1.8 m
*
*
*
2 ft.
610 mm
11 ft.
3.4 m
*
*
*
3 ft.
914 mm
16 ft.
4.9 m
*
*
*
4 ft.
1.2 m
20 ft.
6.1 m
*
*
*
V1 + V2 + H1 = 50 ft. (15.2 m) Maximum
*No specific restrictions on this value EXCEPT
V1 + V2 + H1 cannot exceed 50 ft (15.2 m)
V2
H1
V1
Figure 7.11
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
31
Top Vent - Vertical Termination - (continued)
Three Elbows
V1
H1 + H2
Elbow only
V2
V1 + V2 Minimum
H1 + H2 Maximum
1 ft.
305 mm
*
*
*
1 ft.
305 mm
6 in.
152 mm
2 ft.
610 mm
*
*
*
2 ft.
610 mm
1 ft.
305 mm
2 ft.
610 mm
*
*
*
2 ft.
610 mm
2 ft.
610 mm
4 ft.
1.2 m
*
*
*
4 ft.
1.2 m
3 ft.
914 mm
9 ft.
2.7 m
*
*
*
9 ft.
2.7 m
4 ft.
1.2 m
18 ft.
5.5 m
*
*
*
18 ft.
5.5 m
H1 + H2 = 20 ft. (6.1 m) Maximum
V1 + V2 + H1 + H2 = 40 ft. (12.2 m) Maximum
* No specific restrictions on this value EXCEPT V1 + V2 + H1 + H2 cannot exceed 40 ft. (12.2 m).
V2
H1
H2
V1
INSTALLED
HORIZONTALLY
Figure 7.12
32
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
Rear Vent - Horizontal Termination
H1 = 16 in. (406 mm) Maximum
No Elbow
H1
Figure 7.13
One 45º Elbow
Do not use a 45º elbow in corner installations.
Use two 90º elbows instead.
H1
Figure 7.14
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
33
Rear Vent - Horizontal Termination - (continued)
Two Elbows
H1 Maximum
V1 Minimum
1 ft.
305 mm
Back to Back
90º Elbows
2 ft.
610 mm
6 in.
3 ft.
914 mm
3 ft.
914 mm
3 ft.
3 ft.
H2
H1 + H2 Maximum
1 ft.
305 mm
2 ft.
610 mm
152 mm
2 ft.
610 mm
4 ft.
1.2 m
1 ft.
305 mm
2 ft.
610 mm
5 ft.
1.5 m
2 ft.
610 mm
4 ft.
1.2 m
7 ft.
2.1 m
914 mm
3 ft.
914 mm
9 ft.
2.7 m
12 ft.
3.7 m
914 mm
4 ft
1.2 m
17 ft.
5.2 m
20 ft.*
6.1 m*
V1 + H1 + H2 = 40 ft. (12.2 m) Maximum H1 = 3 ft. (914 mm) Maximum
*H1 + H2 = 20 ft (6.1 m) Maximum
V1
H2
H1
Figure 7.15
H1 Maximum
Three Elbows
INSTALLED
HORIZONTALLY
V1 Minimum
Back to Back
90º Elbows
1 ft.
305 mm
2 ft.
610 mm
6 in.
3 ft.
914 mm
3 ft.
914 mm
3 ft.
3 ft.
H2+ H3
H1+ H2+ H3 Max.
1 ft.
305 mm
2 ft.
610 mm
152 mm
1.5 ft.
457 mm
3.5 ft.
1.1 m
1 ft.
305 mm
2 ft.
610 mm
5 ft.
1.5 m
2 ft.
610 mm
4 ft.
1.2 m
7 ft.
2.1 m
914 mm
3 ft.
914 mm
9 ft.
2.7 m
12 ft.
3.7 m
914 mm
4 ft.
1.2 m
12 ft.
3.7 m
15 ft.
4.6 m
V1+ H1+ H2+ H3= 40 ft. (12.2 m) Maximum H1= 3 ft. (914 mm) Maximum
H1+ H2+ H3= 20 ft. (6.1 m) Maximum
H3
H2
V1
H1
Figure 7.16
34
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
Rear Vent - Vertical Termination
V1 Minimum
One Elbow
H1 Maximum
6 in.
152 mm
2 ft.
610 mm
1 ft.
305 mm
3 ft.
914 mm
2 ft.
610 mm
5 ft.
1.5 m
3 ft.
914 mm
7 ft.
2.1 m
4 ft.
1.2 m
8 ft.
2.4 m
5 ft.
1.5 m
8 ft.
2.4 m
V1 + H1 = 40 ft. (12.2 m) Maximum
H1 = 8 ft. (2.4 m) Maximum
V1
H1
Figure 7.17
V1 Minimum
Two Elbows
Back to Back 90º Elbows
H1 + H2 Maximum
3 ft.
914 mm
2 ft.
610 mm
6 ft.
1.8 m
4 ft.
1.2 m
9 ft.
2.7 m
6 ft.
1.8 m
12 ft.
3.7 m
8 ft.
2.4 m
15 ft.
4.6 m
V1 + H1+ H2 = 40 ft. (12.2 m) Maximum
H1 + H2 = 15 ft. (4.6 m) Maximum
V1
INSTALLED
HORIZONTALLY
H1
H2
Figure 7.18
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
35
Rear Vent - Vertical Termination - (continued)
H1 Maximum
Three Elbows
V2
V1 Minimum
H2
H1 + H2 Maximum
2 ft.
610 mm
6 in.
152 mm
2 ft.
610
mm
4 ft.
1.2 m
3 ft.
914 mm
1 ft.
305 mm
4 ft.
1.2 m
7 ft.
2.1 m
5 ft.
1.5 m
2 ft.
610 mm
6 ft.
1.8 m
11 ft.
3.4 m
7 ft.
2.1 m
3 ft.
914 mm
8 ft.
2.4 m
15 ft.
4.6 m
8 ft
2.4 m
4 ft.
1.2 m
10 ft.
3.1 m
18 ft.
5.5 m
V1 + V2 + H1 + H2= 40 ft (12.2 m) Max.
H1= 8 ft (2.4 m) Max.
H1 + H2 = 20 ft (6.1 m) Max.
H2
V1
Figure 7.19
H1
Three Elbows
H1
H2
H3
V1 Minimum
*
*
*
8 ft.
2.4 m
6 ft.
1.8 m
*
*
*
9 ft.
2.7 m
7 ft.
2.1 m
*
*
*
10 ft.
3.1 m
8 ft.
2.4 m
*
*
*
10 ft.
3.1 m
8 ft.
2.4 m
V1 + H1 + H2 + H3 = 40 ft. (12.2 m) Maximum
*No specific restrictions on this value EXCEPT
V1 + H1 + H2 + H3 cannot exceed 40 ft. (12.2 m) Maximum
H1 + H2 + H3 = 8 ft. (2.4 m) Maximum
V1
H3
H1
H2
Figure 7.20
36
H1 + H2 + H3 Maximum
INSTALLED
HORIZONTALLY
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
Coaxial to Colinear Venting
The coaxial to colinear adapter (DV-46DVA-GCL) is approved for installations into solid fuel masonry or factory
built fireplaces that have been installed in accordance
with the National, Provincial, State and local building
codes. The DV-46DVA-GCL must be recessed into existing masonry fireplace. See Table 1 and Figure 7.21.
OUTSIDE FACE OF
FIREPLACE
EXHAUST VENT PIPE
TOP OF FIREPLACE
OPENING
5 IN. MIN.
INLET AIR VENT PIPE
EXHAUST VENT PIPE
3 IN. MIN.
SHADED AREA DEFINED AS
“INSIDE EXISTING MASONRY
FIREPLACE”
Figure 7.22. Existing Fireplace DV-46DVA-GCL
Clearance Requirements
Figure 7.21. Coaxial/Colinear Appliance Connector
WARNING! Risk of Fire! Coaxial to colinear venting
configuration may only be used in existing non-combustible chimney. Installation in any other venting application
could cause fire.
Clearances to Combustibles:
Refer to Section 5 for clearances to the appliance, mantel, mantel legs and wall projection.
Refer to Section 8 for pipe clearances to combustibles.
Prior to installing the gas appliance:
Termination Cap
• Have the chimney and adjacent structure inspected
and cleaned by qualified professionals. Hearth & Home
Technologies recommends that NFI or CSIA certified
professionals, or technicians under the direction of certified professionals, conduct a minimum of a NFPA 211
Level 2 inspection of the chimney.
For installation of termination cap see minimum vent
heights for various pitched roofs. See Section 6 of appliance owner’s manual.
• Replace component parts of the chimney and fireplace
as specified by the professionals.
Flue Damper
Fully lock the solid fuel fireplace’s flue damper in the open
position, OR completely remove it.
Venting Components
• Ensure all joints are properly engaged and the chimney
is properly secured.
The LINK-DV30B is approved for use with the coaxial/colinear venting application. The LINK-DV30B kit includes:
Table 1
• Two 30 feet sections of flexible vent pipe (3 inches Ø).
One section is used to draw combustion air and the other
section is used to expel exhaust gases.
CLEARANCE TO COMBUSTIBLES REQUIREMENTS
DV-46DVA-GCL
3 IN.
Exhaust Vent Pipe
5 IN.
• One vertical termination cap.
CAUTION! DO NOT use any flue restrictor when venting with the DV-46DVA-GCL adapter and LINK-DV30B
kit. This may result in poor flame appearance, sooting,
pilot malfunction, or overheating.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
37
Connecting the DV-46DVA-GCL Adapter to Appliance
Top Vent
• Remove top seal cap and insulation if equipped. See
Section 14, “Appliance Setup.” Attach the DVP-2SL to
the 8 inch starting collar. Follow installation instructions
included with DVP-2SL kit. Attach the DV-46DVA-GCL
adapter to the appliance starting collar with 3-1/2 in.
self-tapping screws. See Figure 7.23.
Rear Vent
• Remove the rear seal cap and insulation if equipped.
Connect the DVP-2SL adapter to the vertically positioned
elbow. Follow installation instructions included with DVP2SL kit. Secure DV-46DVA-GCL adapter to DVP-2SL with
3-1/2 in. self-tapping screws. See Figure 7.23.
Connecting the LINK-DV30B to the DV-46DVA-GCL
adapter
• Insert the two sections of flexible vent pipe down the
existing chimney.
• Attach one section of stainless steel flex pipe to the
exhaust collar on top of the DV-46DVA-GCL adapter with
three screws.
• Attach one section of flexible vent pipe to the stainless
steel flex pipe with three self-tapping screws.
• Attach one section of flexible vent pipe to the inlet collar
on top of the DV-46DVA-GCL adapter with three selftapping screws.
• To minimize cold air drafts, seal around the flex vents
at the damper inside the chimney with non-combustible
unfaced fiberglass or rock wool insulation.
The DV-46DVA-GCL adapter must be recessed into existing
masonry fireplace. This measurement is taken from the top
of the fireplace opening. See Table 1 and Figure 7.22.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Do NOT connect this gas appliance to a chimney flue
serving a separate solid fuel or gas burning appliance.
• May impair safe operation of this appliance or other
appliances connected to the flue.
• Vent this appliance directly outside.
• Use separate vent system for this appliance.
REAR VENT
TOP VENT
TERMINATION CAP
TERMINATION CAP
CAUTION! DO NOT use any flue restrictor when venting with the DV-46DVA-GCL
adapter and LINK-DV30B kit. This may result in poor flame appearance, sooting, pilot
malfunction, or overheating.
V
NOTICE: To achieve optimum performance of appliance, minimize or avoid
bends in exhaust vent pipe.
V
EXISTING CHIMNEY
EXISTING CHIMNEY
EXHAUST AIR
VENT PIPE
INLET AIR VENT PIPE
The first 3 feet of
exhaust flue must be
stainless flex pipe.
EXISTING CHIMNEY
COAXIAL/COLINEAR
APPLIANCE CONNECTOR
To minimize cold air
drafts, seal with
non-combustible
insulation.
DVP-2SL
DIRECT VENT FIREPLACE
EXHAUST AIR
VENT PIPE
INLET AIR
VENT PIPE
The first 3 feet of
exhaust flue must
be stainless flex
pipe.
EXISTING CHIMNEY
COAXIAL/COLINEAR
APPLIANCE CONNECTOR
To minimize cold air
drafts, seal with
non-combustible
insulation.
DVP-2SL
DIRECT VENT FIREPLACE
HEARTH
FLOOR
FLOOR
HEARTH
H
V
H
Minimum
10 ft.
3.05 m
0 ft.
0 mm
Maximum
40 ft.
12.2 m
2 ft.
610 mm
V
Minimum
10 ft.
3.05 m
Maximum
40 ft.
12.2 m
Figure 7.23
38
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
8
Vent Clearances and Framing
A. Pipe Clearances to Combustibles
B. Wall Penetration Framing
WARNING! Risk of Fire! Maintain air space clearance to
vent. DO NOT pack insulation or other combustibles:
Combustible Wall Penetration
• Between ceiling firestops
• Between wall shield firestops
• Around vent system
Failure to keep insulation or other material away from
vent pipe may cause over heating and fire.
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).
‡DVP heat shield - designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184
mm) thick.
‡,IZDOOWKLFNQHVVLVOHVVWKDQLQWKHH[LVWLQJKHDWVKLHOGVPXVWEHILHOGWULPPHG,I
wall thickness is greater than 7-1/4 in. a DVP-HSM-B will be required.
‡SLP heat shield - designed to be used on a wall 4-3/8 in. to 7-5/8 in. (111 mm to
194 mm thick).
‡,IZDOOWKLFNQHVVLVOHVVWKDQWKHH[LVWLQJKHDWVKLHOGVPXVWEHILHOGWULPPHG
,IZDOOWKLFNQHVVLVJUHDWHUWKDQLQD'93+60%ZLOOEHUHTXLUHG
(DVP-SLP Pipe Shown)
3 in. (76 mm)
top clearance
Heat
Shield
3 in. (76 mm)
top clearance *
Heat
Shield
1 in. (25 mm)
clearance around
vertical sections
1 in. (25 mm)
clearance
bottom & sides
Wall
Shield
Firestop
Whenever a combustible wall is penetrated, you must
frame a hole for the wall shield firestop(s). The wall shield
firestop maintains minimum clearances and prevents cold
air infiltration.
• The opening must be framed on all four sides using the
same size framing materials as those used in the wall
construction.
• SLP pipe - A wall shield firestop must be placed on each
side of an interior wall. A minimum 1-1/2 in. (38 mm)
overlap of attached heat shields must be maintained.
• DVP pipe - A wall shield firestop is required on one side
only on interior walls. If your local inspector requires a
wall shield firestop on both sides, then both wall shield
firestops must have a heat shield (refer to Section 16.B.)
attached to them.
• See Section 10.M. for information for regarding the installation of a horizontal termination cap.
Non-Combustible Wall Penetration
If the hole being penetrated is surrounded by noncombustible materials such as concrete, a hole with diameter
one inch greater than the pipe is acceptable.
Whenever a non-combustible wall is penetrated, the wall
shield firestop is only required on one side and no heat
shield is necessary.
WALL
3 in. (76 mm)
top clearance *
Heat
Shield
Heat
Shield
Wall
Shield
Firestop
1 in. (25 mm)
clearance
bottom & sides
10 in.
C
D
10 in.
WALL
* When using SLP pipe, minimum clearances from the vent pipe to combustible materials at inside wall firestops are:
Top: 2-1/2 in. (64 mm)
Bottom: 1/2 in. (13 mm)
Sides: 1 in. (25 mm)
12 in.
A*
12 in.
B*
Figure 8.1 Horizontal Venting Clearances To Combustible
Materials
6000
8000
in.
mm
in.
mm
A*
42-3/4
1086
44-3/4
1137
B*
27-7/8
708
29-7/8
759
C
41-3/4
1060
44-1/8
1111
D
26-7/8
683
28-7/8
733
* Shows center of vent framing hole for top or rear venting. The center of the
hole is one (1) in. (25.4 mm) above the center of the horizontal vent pipe.
Figure 8.2 Wall Penetration
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
39
C. Install the Ceiling Firestop
A ceiling firestop MUST be used between
floors and attics.
• DVP pipe only - Frame an opening 10 in.
by 10 in. (254 mm by 254 mm) whenever
the vent penetrates a ceiling/fl oor (see
Figure 8.3).
ATTIC ABOVE
• SLP pipe only - Frame opening 9 in. x 9
in. (229 mm x 229 mm) whenever the vent
penetrates a ceiling/floor (see Figure 8.3).
• Frame the area with the same sized lumber
as used in ceiling/floor joist.
A
• The ceiling firestop may be installed above or
below the ceiling joists when installed with a
attic insulation shield. It must be under joists
between floors that are not insulated. Refer
to Figure 8.4.
• Secure with three fasteners on each side.
A
WARNING! Risk of Fire! DO NOT pack insulation around the vent. Insulation must be kept
back from the pipe to prevent overheating.
PIPE
A
D. Install Attic Insulation Shield
DVP
10 in. (254 mm)
WARNING! Fire Risk. DO NOT allow loose
materials or insulation to touch vent. Hearth
& Home Technologies requires the use of an
attic shield.
SLP
9 in. (229 mm)
The International Fuel Gas Code requires an
attic shield constructed of 26 gauge minimum
steel that extends at least 2 in. (51 mm) above
insulation.
• Attic insulation shields must meet specified
clearances to combustible materials and be
secured in place.
• An attic insulation shield kit is available from
Hearth & Home Technologies. Contact your
dealer to order. Install attic insulation shield
according to instructions included with kit.
Figure 8.3 Installing Ceiling Firestop
INSTALL ATTIC INSULATION SHIELDS
BEFORE OR AFTER INSTALLATION OF VENT SYSTEM
CEILING FIRESTOP
INSTALLED BELOW CEILING
Figure 8.4 Installing the Attic Shield
40
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
CEILING FIRESTOP
INSTALLED ABOVE CEILING
E. Installing the Optional Heat-Zone® Gas Kit
• Remove the knockout from the fireplace and discard it
See Figure 8.5.
• Center the duct collar around the exposed hole and
attach it to the fireplace with 3 screws. Note: Do this
BEFORE final positioning of fireplace.
• Determine the location for the air register/fan housing
assembly.
Reference the Heat-Zone® Gas kit instructions for the
remaining installation steps.
HEAT-ZONE® GAS
ATTACHES HERE
Figure 8.5 Heat-Zone® Cover Plate
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
41
9
Appliance Preparation
A. Top Vent
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
NOTICE: Once the seal cap has been removed it CANNOT
be reattached.
NOTICE: Once appliance is set up for top or rear venting,
it CANNOT be changed at a later time.
Figure 9.1 Cut the seal cap strap across the rectangles
next to the disk. For rear vent, skip this step.
Figure 9.4 Remove the insulation basket and white insulation from the center vent pipe.
Figure 9.2 Remove the white gasket material covering
the seal cap.
Figure 9.5 Remove the insulation from the outer vent
pipe. For rear venting there is no insulation in the outer
vent pipe.
Figure 9.3 Remove the seal cap.
42
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
Figure 9.6 To attach the first section of vent pipe, make
sure to use the fiberglass gasket in the manual bag to seal
between the first vent component and the outer fireplace
wrap. Use 2 self tapping screws to secure the gasket to
the outer wrap.
Secure the first section of venting to the fireplace by screwing through the two straps left over from cutting the seal
cap strap in step 2.
Figure 9.9 Fold the center parts of the retaining band out
and use to remove the seal cap.
B. Rear Vent
NOTICE: Once the seal cap has been removed it CANNOT
be reattached.
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
NOTICE: Once appliance is set up for top or rear venting,
it CANNOT be changed at a later time.
Figure 9.7 Fold the tabs toward the center of the seal
cap (90º) and remove the insulation gasket.
Figure 9.10 Discard the vent cap, remove and discard
the insulation basket.
Figure 9.8 Cut the metal retaining band and fold the
sides out.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
43
• Keep nailing tabs flush with the framing.
• Level the appliance from side to side and front to back.
• “Square” the unit by securing diagonal dimensions to
within 1/4 inch of each other. See Figure 9.13.
• Shim the appliance as necessary. It is acceptable to use
wood shims underneath the appliance.
• Secure the appliance to the framing by using nails or
screws through the nailing tabs.
• Secure the appliance to the floor by inserting two screws
through the pilot holes at the bottom of the appliance.
Figure 9.11 Attach the first vent section (it will snap into
place). Slide the insulation gasket onto the vent section,
up against the appliance and over the tabs.
A
B
C. Installing the Non-combustible Board
The factory supplied non-combustible board spans the distance from the top of the fireplace to the center of the framing
header. This board must be used. See Figure 9.12.
HEADER
Note: Diagonal dimensions (A) and (B) must be within
1/4 inch of each other.
Figure 9.13 Positioning the Appliance Squarely
Figure 9.12 Non-combustible Board
D. Securing and Leveling the Appliance
WARNING! Risk of Fire! Prevent contact with:
• Sagging or loose insulation
• Insulation backing or plastic
• Framing and other combustible materials
Block openings into the chase to prevent entry of blownin insulation. Make sure insulation and other materials
are secured.
DO NOT notch the framing around the appliance
standoffs.
Failure to maintain air space clearance may cause
overheating and fire.
The diagram shows how to properly position and secure
the appliance (see Figure 9.15). Nailing tabs are provided
to secure the appliance to the framing members.
• Bend out nailing tabs on each side.
NAILING TABS
(BOTH SIDES)
PILOT HOLES
Figure 9.14 Proper Positioning and Securing of an Appliance
• Place the appliance into position.
44
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
10
Installing Vent Pipe (DVP and SLP Pipe)
A. Assemble Vent Sections (DVP Pipe Only)
Attach Vent to the Firebox Assembly
Note: The end of the pipe sections with the lanced tabs will face
toward the appliance.
Attach the first pipe section to the starting collar:
• Lanced pipe end to the starting collar
• Inner pipe over inner collar
• Push the pipe section until all lanced tabs snap in place
• Lightly tug on pipe to confirm it has locked.
Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications
All outer pipe joints must be sealed with silicone with a
minimum of 300ºF continuous exposure rating, including the
slip section that connects directly to the horizontal termination cap.
Figure 10.1 High Temperature Silicone Sealant
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 10.1
A
Lances
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
Assemble Pipe Sections
B
Figure 10.3
Figure 10.2
Note: Make sure that the seams are not aligned to prevent
Per Figure 10.2:
unintentional disconnection.
• Start the inner pipe on the lanced end of section A into
the flared end of section B.
• Start the outer pipe of section A over the outer pipe of
section B.
• Once both vents sections are started, push firmly until
all lanced tabs lock into place.
• Lightly tug on the pipe to confirm the tabs have locked.
It is acceptable to use screws no longer than 1/2 in. (13
mm) to hold outer pipe sections together. If predrilling holes,
DO NOT penetrate inner pipe.
CORRECT
For 90º and 45º elbows that are changing the vent direction
from horizontal to vertical, one screw minimum should be
put in the outer flue at the horizontal elbow joint to prevent
the elbow from rotating. Use screws no longer than 1/2
in. (13 mm). If predrilling screw holes, DO NOT penetrate
inner pipe.
Figure 10.4 Seams
INCORRECT
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
45
B. Assemble Vent Sections (SLP Pipe Only)
C. Assemble Slip Sections
To attach the first vent component to the starting collars
of the appliance:
• Slide the inner flue of the slip section into the inner flue of
the pipe section and the outer flue of the slip section over
the outer flue of the pipe section. See Figure 10.6.
• Attach a DVP-2SL or DVP-SLP24 adapter to the starting
collar of the appliance.
• Slide together to the desired length.
• Lock the vent components into place by sliding the pipe
section onto the collar.
• Align the seam of the pipe and seam of collar to allow
engagement. Rotate the vent component to lock into
place. Use this procedure for all vent components. See
Figure 10.5.
• Slide the gasket over the first vent section and place it
flush to the appliance. This will prevent cold air infiltration.
Caulk with a minimum of 300ºF continuous exposure rating
may be used to hold the part in place.
Pilot hole
• Continue adding vent components, locking each
succeeding component into place.
Figure 10.6 Slip Section Pilot Holes
• Ensure that each succeeding vent component is securely
fitted and locked into the preceding component.
• Maintain a 1-1/2 in. (38 mm) overlap between the slip
section and the pipe section.
Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications
• Secure the pipe and slip section with two screws no
longer than 1/2 in. (13 mm), using the pilot holes in the
slip section. See Figure 10.7.
For Installation into a commercial, multi-family (multi-level
exceeding two stories) or high-rise applications: All outer
pipe joints must be sealed with silicone with a minimum of
300ºF continuous exposure rating, including the slip section
that connects directly to the horizontal termination cap.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 10.1.
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
Figure 10.7 Screws into Slip Section
• Continue adding pipe as necessary following instructions
in “Assembling Pipe Sections.”
NOTICE: If slip section is too long, the inner and outer flues
of the slip section can be cut to the desired length.
Note: Align seams to engage pipe,
then rotate counterclockwise to lock
Figure 10.5 Adding Venting Components
NOTICE: When installing a vent system with an HRC
termination cap, all pipe system joints shall be sealed
using silicone sealant with a minimum of 300ºF continuous
exposure rating.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections.
• Only outer pipes are sealed, sealing the inner flue is not
required.
• All unit collar, pipe, slip section, elbow and cap outer
flues shall be sealed.
46
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
D. Secure the Vent Sections
E. Disassemble Vent Sections
• Vertical runs originating off the top of the appliance, with
no offsets, must be supported every 8 ft. (2.44 m) after
the maximum allowed 25 ft. (7.62 m) of unsupported rise.
• Rotate either section (see Figure 10.10) so the seams
on both pipe sections are aligned as shown in Figure
10.11.
• Vertical runs originating off the rear of the appliance, or
after any elbow, must be supported every 8 ft. (2.44 m).
• Pull carefully to separate the pieces of pipe.
• Horizontal runs must be supported every 5 feet (1.52
m).
• Vent supports or plumbers strap (spaced 120º apart)
may be used to support vent sections. See Figures 10.8
and 10.9.
• Wall shield firestops may be used to provide horizontal
support to vent sections.
• SLP ceiling firestops have tabs that may be used to
provide vertical support.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Improper support could allow vent to sag and separate.
Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below
connection point to appliance.
Figure 10.10 Rotate Seams for Disassembly
120º
Figure 10.11 Align and Disassemble Vent Sections
Figure 10.8 Securing Vertical Pipe Sections
120º
Figure 10.9 Securing Horizontal Pipe Sections
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
47
F. Install Decorative Ceiling Components
(SLP only)
LEVEL
A decorative ceiling thimble can be installed on a flat ceiling through which the vent passes. The decorative ceiling
thimble is used to cover the firestop.
CATHEDRAL CEILING
SUPPORT BOX
• Seal the gap between the vent pipe and firestop using
silicone with a minimum of 300ºF continuous exposure
rating to prevent cold air infiltration.
• Install the decorative ceiling thimble by sliding it up to
the ceiling and attaching it using the provided screws.
A decorative cathedral ceiling support box can be installed
on a cathedral ceiling through which the vent passes.
• Use a plumb-bob to mark the center line of the venting
system on the ceiling and drill a small hole through the
ceiling and roof at this point. Locate the hole and mark
the outline of the cathedral ceiling support box on the
outside roof.
2 in. (51 mm) MIN. BELOW
FINISHED CEILING
CUT HOLE 1/8 in. (3 mm)
GREATER IN SIZE THAN
PATTERN OF SUPPORT
BOX AS IT IS PROJECTED
ONTO ROOF LINE
Figure 10.12
• Remove shingles or other roof covering as necessary
to cut the rectangular hole for the support box. Cut the
hole 1/8 in. (3 mm) larger than the support box outline.
• Lower the support box through the hole in the roof until its
bottom is at least 2 in. (51 mm) below the ceiling (Figure
10.12).
• Level the support box both vertically and horizontally and
temporarily tack it in place through the inside walls into
the roof sheathing.
• Use tin snips to cut the support box from the top corners
down to the roof line and fold the resulting flaps to the
roof. See Figure 10.13.
• Nail the flaps to the roof AFTER running a bead of non
hardening sealant between the flaps and the roof.
WARNING! Risk of Fire! Clean out ALL materials from
inside the support box and complete the vertical vent run
and termination.
48
Figure 10.13
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
G. Install Metal Roof Flashing
• See minimum vent heights for various pitched roofs
(Figure 10.14) to determine the length of pipe to extend
through the roof.
CAULK
• Slide the roof flashing over the pipe sections extending
through the roof as shown in Figure 10.15.
HORIZONTAL
OVERHANG
2 FT.
MIN.
20 INCHES MIN.
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
Figure 10.15
GAS DIRECT VENT
TERMINATION CAP
H. Assemble and Install Storm Collar
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
Roof Pitch
H (Min.) Ft.
Flat to 6/12........................................ 1.0*
Over 6/12 to 7/12 ............................ 1.25*
Over 7/12 to 8/12 .............................. 1.5*
Over 8/12 to 9/12 .............................. 2.0*
Over 9/12 to 10/12 ............................ 2.5*
Over 10/12 to 11/12 ......................... 3.25
Over 11/12 to 12/12 ........................... 4.0
Over 12/12 to 14/12 ........................... 5.0
Over 14/12 to 16/12 ........................... 6.0
Over 16/12 to 18/12 ........................... 7.0
Over 18/12 to 20/12 ........................... 7.5
Over 20/12 to 21/12 ........................... 8.0
* 3 foot minimum in snow regions
Figure 10.14 Minimum Height From Roof To Lowest Discharge
Opening
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
•
•
Slide the storm collar onto the exposed pipe section
and align brackets.
Insert a bolt (provided) through the brackets and install
nut. Do not completely tighten.
Figure 10.16 Assembling the Storm Collar Around the Pipe
•
Slide the assembled storm collar down the pipe section
until it rests on the roof flashing. See Figure 10.16.
•
Tighten nut and make sure the collar is tight against the
pipe section.
•
Caulk around the top of the storm collar. See Figure 10.17.
NOTICE: Failure to properly caulk the roof flashing and
pipe seams may permit entry of water.
• Caulk the gap between the roof flashing and the outside
diameter of the pipe.
• Caulk the perimeter of the flashing where it contacts the
roof surface. See Figure 10.15.
• Caulk the overlap seam of any exposed pipe sections
that are located above the roof line.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
49
I. Install Vertical Termination Cap
• Attach the vertical termination cap by sliding the inner
collar of the cap into the inner flue of the pipe section
while placing the outer collar of the cap over the outer
flue of the pipe section.
• Secure the cap by driving three self-tapping screws
(supplied) through the pilot holes in the outer collar of
the cap into the outer flue of the pipe (see Figure 10.17).
K. Heat Shield Requirements for Horizontal
Termination
WARNING! Risk of Fire! To prevent overheating and fire,
heat shields must extend through the entire wall thickness.
• DO NOT remove the heat shields attached to the
wall shield firestop and the horizontal termination cap
(shown in Figure 10.19).
• Heat shields must overlap 1-1/2 in. (38 mm) minimum.
Termination Cap
There are two sections of the heat shield. One section
is factory-attached to the wall shield firestop. The other
section is factory-attached to the cap. See Figure 10.19.
If the wall thickness does not allow the required 1-1/2 in.
(38 mm) heat shield overlap when installed, an extended
heat shield must be used.
• If the wall thickness is less than 4 in./102 mm (DVP)
or 4-3/8 in./ 111 mm (SLP), the heat shields on the cap
and wall shield firestop must be trimmed. A minimum
1-1/2 in. (38 mm) overlap MUST be maintained.
(1 of 3)
Screws
Storm
Collar
Caulk
• Use an extended heat shield if the finished wall thickness
is greater than 7-1/4 in. (184 mm).
• The extended heat shield may need to be cut to length
maintaining sufficient length for a 1-1/2 in. (38 mm)
overlap between heat shields.
• Attach the extended heat shield to either of the existing
heat shields using the screws supplied with the extended
heat shield. Refer to vent components diagrams in the
back of this manual.
Figure 10.17
J. Install Decorative Wall Components (SLP
only)
A decorative wall thimble can be installed on wall through
which the vent passes. The decorative wall thimble is used
to cover the wall shield firestop.
• Rest the small leg on the extended heat shield on top
of the pipe section to properly space it from the pipe
section.
Important Notice: Heat shields may not be field constructed.
• Slide the decorative wall thimble over the last section of
horizontal pipe before connecting the termination cap to
the pipe.
• Once the pipe section and the termination cap have
been connected, slide the wall thimble up to the interior
wall surface and attach with screws provided. See Figure
10.18.
Figure 10.18 Wall Thimble
50
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
L. Install Horizontal Termination Cap (DVP
and SLP Pipe)
WARNING! Risk of Fire! The telescoping flue section of
the termination cap MUST be used when connecting vent.
• 1-1/2 (38 mm) minimum overlap of flue telescoping
section is required.
Failure to maintain overlap may cause overheating and
fire.
Note: When using termination caps with factory-supplied
heat shield attached, no additional wall shield firestop is
required on the exterior side of a combustible wall.
WALL SHIELD
FIRESTOP
• Vent termination must not be recessed in the wall. Siding
may be brought to the edge of the cap base.
CAUTION! Risk of Burns! Local codes may require installation of a cap shield to prevent anything or anyone
from touching the hot cap.
NOTICE: For certain exposures which require superior
resistance to wind-driven rain penetration, a flashing kit and
HRC caps are available. When penetrating a brick wall, a
brick extension kit is available for framing the brick.
HEAT SHIELD
1-1/2 IN. (38 MM) MIN.
OVERLAP
SLIP SECTION
CAN BE EXTENDED
• Flash and seal as appropriate for siding material at
outside edges of cap.
• When installing a horizontal termination cap, follow
the cap location guidelines as prescribed by current
ANSI Z223.1 and CAN/CGA-B149 installation codes
and refer to Section 6 of this manual.
HEAT SHIELD OR
EXTENDED
HEAT SHIELD
INNER VENT
SHEATHING
OUTER VENT
INTERIOR
EXTERIOR
VENT DEPTH FROM BACK OF APPLIANCE TO
OUTSIDE SURFACE OF EXTERIOR WALL
(SEE CHART BELOW)
Figure 10.19 Venting through the wall
Cap Specification Chart
(depth without using additional pipe sections)
6000
Series
8000
Series
DVP-TRAPK1 DVP-TRAP1 DVP-TRAPK2 DVP-TRAP2
Top Vent
Rear Vent
Top Vent
Rear Vent
Depth
Depth
Depth
Depth
2-3/4 in. to
3-1/8 in. to
5-1/8 in. to
5-1/2 in. to
4-5/8 in.
5 in.
9-1/8 in.
9-1/2 in.
DVP-HPC1
Top Vent
Depth
2-3/4 in. to
4-7/8 in.
DVP-HPC1
Rear Vent
Depth
3-1/8 in. to
5-1/4 in.
DVP-HPC2
Top Vent
Depth
4-7/8 in. to
9 in.
DVP-HPC2
Rear Vent
Depth
5-1/4 in. to
9-3/8 in.
DVP-TRAP1 can adjust 1-1/2 in. (3-1/8 to 4-5/8 in.)
DVP-TRAP2 can adjust 4 in. (5-3/8 to 9-3/8)
DVP-HPC1 can adjust 2-1/8 in. (4-1/4 to 6-3/8)
DVP-HPC2 can adjust 4-1/8 in. (6-3/8 to 10-1/2)
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
51
11
Gas Information
A. Fuel Conversion
C. Gas Connection
• Make sure the appliance is compatible with available gas
types.
• Refer to Reference Section 16 for location of gas line
access in appliance.
• Conversions must be made by a qualified service
technician using Hearth & Home Technologies specified
and approved parts.
• Gas line may be run through knockout(s) provided.
B. Gas Pressure
• Optimum appliance performance requires proper input
pressures.
• Gas line sizing requirements will be determined in ANSI
Z223.1 National Fuel Gas Code in the USA and CAN/
CGA B149 in Canada.
• Pressure requirements are:
Gas Pressure
• The gap between supply piping and gas access hole may
be caulked with caulk with a minimum of 300ºF continuous
exposure rating or stuffed with non-combustible, unfaced
insulation to prevent cold air infiltration.
• Ensure that gas line does not come in contact with outer
wrap of the appliance. Follow local codes.
• Pipe incoming gas line into valve compartment.
• Connect incoming gas line to the 1/2 in. (13 mm)
connection on manual shutoff valve.
WARNING! Risk of Fire or Explosion! Support control
when attaching pipe to prevent bending gas line.
Natural Gas
Propane
Minimum inlet pressure
5.0 in. w.c.
11.0 in. w.c.
• A small amount of air will be in the gas supply lines.
Maximum inlet pressure
10.0 in. w.c.
13.0 in. w.c.
Manifold pressure
3.5 in. w.c.
10.0 in. w.c.
WARNING! Risk of Fire or Explosion! Gas build-up during line purge could ignite.
WARNING! Risk of Fire or Explosion! High pressure
will damage valve. Low pressure may cause explosion.
• Verify inlet pressures. Verify minimum pressures when
other household gas appliances are operating.
• Install regulator upstream of valve if line pressure is
greater than 1/2 psig.
WARNING
Fire Risk.
Explosion Hazard.
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
Note: Have the gas supply line installed in accordance with
local codes, if any. If not, follow ANSI 223.1. Installation
should be done by a qualified installer approved and/or
licensed as required by the locality. (In the Commonwealth
of Massachusetts installation must be performed by a
licensed plumber or gas fitter).
Note: A listed (and Commonwealth of Massachusetts approved) 1/2 in. (13 mm) T-handle manual shut-off valve
and flexible gas connector are connected to the 1/2 in. (13
mm) control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
52
• Purge should be performed by qualified service
technician.
• Ensure adequate ventilation.
• Ensure there are no ignition sources such as sparks
or open flames.
Light the appliance. It will take a short time for air to purge
from lines. When purging is complete the appliance will
light and operate normally.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Check all fittings and connections with a non-corrosive
commercially available leak-check solution. DO NOT use
open flame. Fittings and connections could have loosened during shipping and handling.
WARNING! Risk of Fire! DO NOT change valve settings.
This valve has been preset at the factory.
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
When installing above 2000 feet elevation:
• In the USA: Reduce burner orifice 4% for each 1000 feet
above 2000 feet.
• In CANADA: Reduce burner orifice 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
12
Electrical Information
A. Wiring Requirements
B. IntelliFire Plus™ Ignition System Wiring
NOTICE: This appliance must be electrically wired
and grounded in accordance with local codes or, in the
absence of local codes, with National Electric Code
ANSI/NFPA 70-latest edition or the Canadian Electric
Code CSA C22.1.
• Wire the appliance junction box to 110-120 VAC. This is
required for use of optional accessories (standing pilot
ignition) or proper operation of the appliance (IntelliFire
Plus™ ignition).
• Wire the appliance junction box to 110-120 VAC for
proper operation of the appliance.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in
compliance with the applicable electrical codes, when
it is installed in locations such as in bathrooms or near
sinks.
• Low voltage and 110-120 VAC voltage cannot be shared
within the same wall box.
WARNING! Risk of Shock or Explosion! DO NOT wire
110V to the valve or to the appliance wall switch. Incorrect
wiring will damage controls.
Determine if the appliance uses an IntelliFire Plus™ ignition system or standing pilot ignition system:
• Open the control access panel or remove the decorative
front.
• A red or black ignitor button (as shown in Figure 12.1)
indicates this appliance is standing pilot ignition.
RED OR
BLACK
BUTTON
WARNING! Risk of Shock or Explosion! DO NOT wire
IPI controlled appliance junction box to a switched circuit.
Incorrect wiring will override IPI safety lockout.
• Refer to Figure 12.2, IPI Wiring Diagram.
• This appliance is equipped with an IntelliFire Plus™
control valve which operates on a 6 volt/1.5 AMP
system.
• Plug the 6 volt transformer plug into the appliance junction
box to supply power to the unit OR install 4 AA cell
batteries (not included) into the battery pack before use.
C. Standing Pilot Ignition System Wiring
• The standing pilot ignition system wiring does not require
a 110-120 VAC supply to operate. See Figure 12.3
• A 110-120 VAC junction box MUST be installed for use
with a fan or remote control. See Figure 12.4 for junction
box wiring. Keep wire lengths short as possible.
NOTICE: DO NOT wire 110 VAC to the millivolt valve! This
will damage the valve.
• If using a thermostat use one compatible with a millivolt
gas valve system:
- Install the thermostat in the location as indicated in the
thermostat instructions to ensure proper operation of
appliance.
- Use low resistance thermostat wire for wiring from
ignition system to the wall switch and thermostat.
- Keep wire lengths short as possible.
D. Optional Accessories Requirements
• This appliance may be used with a wall switch, wall
mounted thermostat and/or a remote control.
Figure 12.1 Ignitor Button
Wiring for optional Hearth & Home Technologies approved
accessories should be done now to avoid reconstruction.
Follow instructions that come with those accessories.
• Hearth & Home Technologies recommends that IntelliFire PlusTM wireless controls be used for their features
and functionality with the IntelliFire PlusTM ignition system.
• A standard ON/OFF switch is compatible.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
53
FLAME
SENSE
IGNITER
TO JUNCTION
BOX (110V)
MODULE
FLAME
MODULATION
RC100
RC200
(OPTIONAL WALL CONTROLS)
ORANGE
(PILOT)
GREEN
(MAIN)
BATTERY PACK
6V DC
BLACK
RED
BLACK
BLACK
RED
BLACK
THERMOSTAT
WIRE
ASSEMBLY/
WALL SWITCH
WIRE
BROWN
GROUND
Figure 12.2 IPI Wiring Diagram
STANDING
PILOT
BRN
RED
VALVE
WHT
ON/OFF PIGGYBACK WIRE
THERMOSTAT
WIRE ASSEMBLY / WALL
SWITCH WIRE
RED
Figure 12.3 Standing Pilot Ignition Wiring Diagram
54
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
E. Electrical Service and Repair
WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can
cause improper and dangerous operation. Verify proper
operation after servicing.
Romex
Connector
14/2WG
WARNING! Risk of Shock! Replace damaged wire with
type 105º C rated wire. Wire must have high temperature
insulation.
Cover Plate
outside firebox
F. Junction Box Installation
HT
If the box is being wired from the INSIDE of the appliance:
WHT B
LK
BLK
W
• Remove the screw attaching the junction box/receptacle to
the outer shell, rotate the junction box inward to disengage
it from the outer shell (see Figure 12.4).
• Pull the electrical wires from outside the appliance through
the opening into the valve compartment and secure wires
with a Romex connector. See Figure 12.4.
• Make all necessary wire connections to the junction box/
receptacle and reattach the junction box/receptacle to the
outer shell.
Copper
ground attached
to GRN screw with
GRN wire
GRN wire
inside box
NOTICE: DO NOT wire 110-120 VAC
to wall switch.
Figure 12.4 Junction Box Detail
G. Wall Switch Installation for Fan (Optional)
If the box is being wired to a wall mounted switch for use
with a fan (See Figure 12.5):
• The power can then be supplied from the switch box to the
appliance using a minimum of 14-3 with ground wire.
Red
Black
White
Green
Junction Box
• At the switch box connect the black (hot) wire and red
(switch leg) wire to the wall switch as shown.
Switch Box
• At the appliance connect the black (hot), white (neutral)
and green (ground) wires to the junction box as shown.
• Add a 1/4 in. insulated female connector to the red (switch
leg) wire, route it through the knockout in the face of the
junction box, and connect to the top fan switch connector
(1/4 in. male) as shown.
Black
White
Green
Red
Black
White
Green
• The power supply for the appliance must be brought into
a switch box.
Switch
Minimum 14-3 AWG
with Ground
Power
Supply
Wires
Knockout
Red
Figure 12.5 Junction Box Wired to Wall Switch or BC10
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
55
13
Finishing
A. Mantel and Wall Projections
B. Facing Material
WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing closer than the minimums listed must be constructed entirely of noncombustible materials
(i.e., steel studs, concrete board, etc.)
• Metal front faces may be covered with non-combustible
materials only.
Mantels - Combustible or Painted Surfaces
Note: All
measurements
in inches.
• Facing and/or finishing materials must never overhang
into the glass opening.
TO CEILING
18
12
11
10
32
9
25
8
7
5
3
17
4
• Observe all clearances when applying combustible
materials.
• Seal joints between the finished wall and appliance top
and sides using a 300ºF minimum sealant. Refer to
Figure 13.3.
WARNING! Risk of Fire! DO NOT apply combustible
materials beyond the minimum clearances. Comply with
all minimum clearances to combustibles as specified in
this manual. Overlapping materials could ignite and will
interfere with proper operation of doors and louvers.
19
6
• Facing and/or finishing materials must not interfere with
air flow through louvers, operation of louvers or doors,
or access for service.
18
16
15
14
13
12
2-1/2
11
10
B
5
FACTORY-INSTALLED NON-COMBUSTIBLE BOARD
DO NOT REMOVE
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
Note: Measurement is taken from top of the opening,
NOT the top of the fireplace.
Figure 13.1 Minimum Vertical and Maximum Horizontal
Dimensions
A
Mantel Legs or Wall Projections - Combustible or
Painted Surfaces
INTERIOR WALL
TOP VIEW
A
B
6000
FIREPLACE OPENING
8000
MANTEL LEG OR WALL PROJECTIONS
If
A
B
A minimum is ____, then B maximum is_____.
Inches
B
39-3/4
41
millimeters
1010
1041
inches
41-3/4
48
millimeters
1060
1219
inches
Figure 13.3 Noncombustible Facing Diagram
2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16
Inches
62
1
87
2
113
3
138
4
164
5
Millimeters
25
51
76
102
127
Millimeters
A
189


Figure 13.2 Clearances to Mantel Leg or Wall Projections
(Acceptable on both sides of opening)
56
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
C. Doors
Only doors certified for use with this appliance model may
be used. Contact your dealer for a list of doors that may
be used. Once you have determined what kind of door
and finishing material is going to be used on the fireplace,
you may use the table below which shows the door models and the finishing material thickness allowed.
DOOR
Folio
Arcadia
Halston
Chateau
MT Hammer
Galleria
CF
FIT
FINISH MATERIAL
THICKNESS
SEE
FIGURE
Inside
Any
13.6
Overlap
1 inch or less
13.4
Inside
Greater than 1 inch
13.5
Overlap
1 inch or less
13.4
Inside
Greater than 1 inch
13.5
Overlap
1 inch or less
13.4
Inside
Greater than 1 inch
13.5
Overlap
1 inch or less
13.4
Inside
Greater than 1 inch
13.5
Overlap
1 inch or less
13.4
Inside
Greater than 1 inch
13.5
Inside
Any
13.6
Note: Finishing strips may be used to aid in positioning of
non-combustible facing materials for some of the facing and
door combinations specified in the table above. They must
be removed following finishing work. See figure 13.7.
Finishing Material:
1 Inch Thick or Less
Remove Finishing Strips. See Figure 13.7.
NOTICE: Remove finishing strips before firing appliance.
DOOR
1 in. MAX.
FINISHING MATERIAL
(TOP EDGE)
Finishing materials 1 inch maximum thick.
Stop finishing material flush with opening.
FINISHING STRIP NOT USED
(See Figure 13.7 for
removal instructions)
NON-COMBUSTIBLE
FINISHING MATERIAL
Figure 13.4 Finishing Material 1 Inch Thick or Less
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
57
Finishing Material Thickness:
1-4 inches maximum
Finishing Material Thickness:
0-4 inches maximum
NOTICE: Remove finishing strips before firing appliance.
NOTICE: Remove finishing strips before firing appliance.
FINISHING
STRIPS USED
FINISHING STRIP NOT USED
(See Figure 13.7 for
removal instructions)
NON-COMBUSTIBLE
FINISHING MATERIAL
FINISHING
MATERIAL
NON-COMBUSTIBLE
FINISHING MATERIAL
FINISHING
MATERIAL
DOOR
A
(Outside door width)
C
(Includes 1/8 in. opening each side of door)
DOOR
FINISHING MATERIAL
FINISHING MATERIAL
Figure 13.6 Folio/CF Inside Fit
B
8000 Models
D
A
(Outside door width)
C
Inches
Millimeters
Inches
Millimeters
A
44-1/16
1119
37-1/16
941
B
35-15/16
913
34-1/16
865
C
44-5/16
1126
37-5/16
948
D
36-5/16
922
34-7/16
882
(Includes 1/8 in. opening each side of door)
Finishing material thickness, 1-4 inches maximum
B = Top of door to bottom of fireplace.
D = Bottom of Finishing Material to Bottom of Fireplace
Figure 13.5 Finishing Material Thickness Greater Than One Inch
58
6000 Models
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
Removal of Finishing Strips
NOTICE: Remove finishing strips before firing appliance.
Remove glass frame assembly to access finishing strip
screws.
FINISHING STRIPS REMOVED
Figure 13.7 Removing Finishing Strips.
31-7/8 IN. (6000)
33-11/16 IN. (8000)
3-3/4 IN.
(6000, 8000)
35-5/16 IN. (6000)
43 IN. (8000)
Figure 13.8. Clean Face Door Dimensions
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
59
D. Elevated Hearth Systems
Use the table below to identify the hearth system that will be used. The table will also help identify effects on the various
dimensions. Some hearth systems will elevate the appliance off the floor at a given dimension. For example, if appliance
will be used with a Kenwood Cabinet with Base, the appliance will be elevated 9-1/4 in. The 9-1/4 in. elevation will also
have to be added to the following: Wall penetration referenced in Figure 8.2 (Wall penetration) and Rough Opening Height
(header height) referenced in Figure 5.2. Note: Finished floor thickness should also be considered when determining installation dimensions.
MODEL
6000
Series
8000
Series
DESCRIPTION
PART #
KENWOOD CABINET
KENWOOD CABINET W/ BASE
KENWOOD CORNER CABINET
KENWOOD CORNER CABINET W/ BASE
KENWOOD MANTEL
KENWOOD MANTEL W/ BASE
LUNA SURROUND
KENWOOD MANTEL
KENWOOD MANTEL W/ BASE
KDC48DBP
KDC48DBP W/ HTKDC48DBP
KDA48DBP
KDA48DBP W/ HTKDA48DBP
AFKDMPB
AFKDMPB W/ HTKDMPB
LUNA-36-GY
AFKDMPC
AFKDMPC W/ HTKDMPC
ELEVATED APPLIANCE
DIMENSION
See Note 1
0
9-1/4 in.
0
9-1/4 in.
0 (See Note 3)
9-1/4 in.
1-1/16 in.
0 (See Note 3)
9-1/4 in.
MARBLE LEG CUT
LENGTH
See Note 2
33 in.
33 in.
33 in.
33 in.
33 in.
33 in.
N/A
32-7/8 in.
32-7/8 in.
Note 1. Add dimensions to Wall Penetration (Figure 8.2) and Rough Opening Height (Figure 5.2).
Note 2. Verify Marble Cut Lengths on site prior to cutting.
Note 3. Dimensions assume use of a 3/4 in. Hearth Pad.
60
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
14
Appliance Setup
A. Remove Fixed Glass Assembly
F. Ember Placement
See Section 14.H.
WARNING! Risk of Explosion! Follow ember placement
instructions in manual. DO NOT completely block burner
ports with ember material. Replace ember material annually. Improperly placed embers interfere with proper burner
operation.
B. Remove the Shipping Materials
Remove shipping materials from inside or underneath the
firebox.
C. Clean the Appliance
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity.
D. Accessories
Install approved accessories per instructions included
with accessories. Contact your dealer for a list of approved accessories.
WARNING! Risk of Fire and Electric Shock! Use ONLY
Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories
could result in a safety hazard and will void the warranty.
Ember material is shipped with this gas appliance. To place
the ember material:
• Embers CANNOT completely block burner ports. Care
should be taken not to block the lighting trail of ports.
• Embers may only be placed in areas as shown in Figure
14.2.
• LP Only: Using dime-size pieces of Glowing Embers®,
overlap the burner ports (see Figure 14.3). The impingement
created by the embers will help blend the fire.
• Save the remaining ember materials for use during
appliance servicing. The embers provided should be
enough for 3 to 5 applications.
E. Burner Top Installation
1. Bend the two tabs upward as shown in Figure 14.1.
EMBERS
NO EMBERS IN SHADED AREAS
2. To install the fiber burner, mate the locating holes with
the guide sleeves. Install fiber burner top so that it
makes full contact with the underlying burner assembly.
3. Ensure that the ports in the steel burner are visible
through the holes in the fiber burner top.
FIBER BURNER TOP
LOCATING HOLES
Figure 14.2 Placement of Embers
BEND TABS UP
AIR SCOOP
BURNER ASSEMBLY
PILOT COVER
BURNER SHIELD
GUIDE SLEEVES
Figure 14.3 Embers Overlapping Burner Port Holes (LP only).
Figure 14.1
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
61
G. Install the Log Assembly
Log Assembly: LOGS-6C
Models: 6000C-IPILP, 6000CBV-IPI
6000C, 6000C-IPI
FIBER BURNER TOP
LOCATING HOLES
LOG PLACEMENT TABS
TAB BENT IN = NG
BURNER SHIELD
PILOT COVER
LOG PLACEMENT INDENTATIONS
BURNER ASSEMBLY
TAB NOT BENT = LP
GUIDE SLEEVES
GRATE TINE
Figure 1
Figure 2. Log Placement Tabs
CAUTION: Logs are fragile, handle with care. Log #1 (SRV2164-701): Locate log placement tabs on the pilot cover. Bend
tabs upward as shown in Figure 2. Locate the log placements slots on the bottom of Log # 1 (see Figure 3). Mate the slots
located on the bottom of Log #1 with the log placement tabs on the pilot cover. Log # 1 is properly installed when it sits
squarely and completely on pilot cover with tabs engaged (see Figure 4).
LOG PLACEMENT TABS
1
Figure 3
LOG PLACEMENT SLOTS
Figure 4
Figure 4 shows the log placement tabs located on the top of Log # 1. The tabs will be mated with the slots located on the
bottom of Log #2 and Log #3 (see Figure 5). Log #2 and Log #3 also have grooves that allow the logs to be seated properly
on the grate (see Figure 5). Hold Log #1 upright while placing Log #2.
Bottom view of
Logs # 2 and 3
LEFT GRATE TINE
SLOTS
2
2
3
1
GROOVES
Figure 5
Figure 6
Log #2 (SRV2164-702): Mate the slot located on the bottom of Log #2 with the left tab on top of Log #1. After slot and tab
have been fitted together, mate the groove located on the bottom of Log #2 with the horizontal grate bar and slide Log # 2
toward the left until it rests against the far left grate tine.
62
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
NOSE
RIGHT GRATE TINE
1
1
3
2
2
3
4
Figure 7
Figure 8
Log #3 (SRV2164-703): Mate the slot located on the bottom of Log #3 with the right log placement tab on top of Log #1.
After slot and tab have been fitted together, mate the groove located on the bottom of Log #3 with the horizontal grate bar
and slide Log # 3 toward the right until it rests against the far right grate tine (see Figure 7).
Log #4 (SRV2164-704): Place Log #4 in the left log indentation on the burner top (see Figure 2). Slide Log # 4 from right
to left under Log #2 to fit completely and securely into the indentation (see Figure 8). Nose of log #4 should be pulled to fit
securely against right hand side of log indentation.
LOG #6 CONTACTS TOP OF LOG #4
FLAT AREA
1
1
4
Figure 9
2
3
2
5
3
4
Figure 10
6
5
LOG CONTACTS GRATE TINES
Log #5 (SRV2164-705): Place Log #5 in the right log indentation on the burner top (see Figure 2). Ensure the log fits
completely and securely in the recessed indentation (see Figure 9). Log #5 should be pulled to the left hand side of log
indentation.
Log #6 (SRV2164-706): Mate the groove located on the lower end of Log #6 with the fourth grate tine (from left to right) as
shown in Figure 10. Set the other end of Log #6 on the flat area located on top of Log #4 (see Figure 9). Log #6 will also
rest against center grate tine. When properly installed, Log #6 will rest securely on all 3 contact points, not allowing movement or shifting.
2164-935C
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
63
G. Install the Log Assembly (continued)
Log Assembly: LOGS-8C
Models: 8000C, 8000C-LP, 8000C-IPI,
8000C-IPILP, 8000CBV-IPI
FIBER BURNER TOP
LOCATING HOLES
LOG PLACEMENT INDENTATIONS
TAB BENT IN = NG
LOG PLACEMENT TABS
BURNER SHIELD
PILOT COVER
BURNER ASSEMBLY
TAB NOT BENT = LP
GRATE TINE
GUIDE SLEEVES
Figure 2. Log Placement Tabs
Figure 1
CAUTION: Logs are fragile, handle with care. Log #1 (SRV2168-701): Locate log placement tabs on the pilot cover. Bend
tabs upward as shown in Figure 2. Locate the log placements slots on the bottom of Log # 1 (see Figure 3). Mate the slots
located on the bottom of Log #1 with the log placement tabs on the pilot cover. Log # 1 is properly installed when it sits
squarely and completely on pilot cover with tabs engaged. See Figure 4.
LOG PLACEMENT TABS
1
LOG PLACEMENT SLOTS
Figure 3
Figure 4
Figure 4 shows the log placement tabs located on the top of Log # 1. The tabs will be mated with the slots located on the
bottom of Log #2 and Log #3 (see Figure 5). Log #2 and Log #3 also have grooves that allow the logs to be seated properly
on the grate (see Figure 5). Hold Log #1 upright while placing Log #2.
Bottom view of
Logs # 2 and 3
LEFT GRATE TINE
SLOTS
2
2
3
1
GROOVES
Figure 5
Figure 6
Log #2 (SRV2168-702): Mate the slot located on the bottom of Log #2 with the left log placement tab on top of Log #1.
After slot and tab have been fitted together, mate the groove located on the bottom of Log #2 with the horizontal grate bar
and slide Log # 2 toward the left until it rests against the far left grate tine.
64
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
RIGHT GRATE TINE
1
3
2
1
2
3
4
HORIZONTAL GRATE BAR
Figure 7
LOG #4 CONTACTS LOG #2
Figure 8
Log #3 (SRV2168-703): Mate the slot located on the bottom of Log #3 with the right log placement tab on top of Log #1.
After slot and tab have been fitted together, mate the groove located on the bottom of Log #3 with the horizontal grate bar
and far right grate tine. Log # 3 will sit down on top of both the grate tine and the horizontal grate bar (see Figure 7).
Log #4 (SRV2168-704): Place Log #4 in the left log indentation on the burner top (see Figure 2). Slide Log # 4 from right to
left under Log #2 to fit completely and securely into the indentation (see Figure 8). The back or Log # 4 should rest against
the far left grate tine as well as contact Log # 2.
LOG #6 CONTACTS TOP OF LOG #4
FLAT AREA
1
2
3
4
Figure 9
1
2
5
4
Figure 10
6
3
5
LOG CONTACTS GRATE TINES
Log #5 (SRV2168-705): Place Log #5 in the right log indentation on the burner top (see Figure 2). Ensure the log fits
completely and securely in the indentation (see Figure 9). Log #5 should be pulled to the left hand side of log indentation.
Log #6 (SRV2168-706): Mate the groove located on the lower end of Log #6 with the fourth tine (from left to right) as
shown in Figure 10. Set the other end of Log #6 on the flat area located on top of Log #4 (see Figure 9). Log #6 will
also rest against center grate tine. When properly installed, Log #6 will rest securely on all 3 contact points, not allowing
movement or shifting.
2168-935C
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
65
H. Fixed Glass Assembly
J. Air Shutter Setting
WARNING! Risk of Asphyxiation! Handle fixed glass
assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.
Air shutter settings should be adjusted by a qualified service technician at the time of installation. The air shutter is
set at the factory for minimum vertical vent run. Adjust air
shutter for longer vertical runs. See Figure 14.5.
• DO NOT strike, slam or scratch glass.
• DO NOT operate fireplace with glass removed, cracked,
broken or scratched.
• Replace as a complete assembly.
• Loosen the wing nut.
Removing Fixed Glass Assembly
• Pull the four glass assembly latches out of the groove on
the glass frame. Remove glass door from the appliance
(see Figure 14.4).
• Move the air handle to the left to open the air shutter.
• Move the air handle to the right to close the air shutter.
• Tighten the wing nut.
NOTICE: If sooting occurs, provide more air by opening
the air shutter.
Replacing Fixed Glass Assembly
• Replace the glass door on the appliance. Pull out and
latch the four glass assembly latches into the groove on
the glass frame.
AIR SHUTTER
WING NUT
LATCHES
(BOTH BOTTOM
AND TOP)
Figure 14.5 Air Shutter
GLASS
ASSEMBLY
Air Shutter Settings
Figure 14.4 Fixed Glass Assembly
NG
LP
6000
1/4 in.
3/4 in.
8000
1/4 in.
3/4 in.
I. Install Trim and/or Surround
• Install optional trim kits and/or surrounds using the
instructions included with the accessory.
• Use non-combustible materials to cover the gap between
the sheet rock and the appliance (when applicable to the
model).
66
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
15
Troubleshooting
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and
the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact
your dealer to arrange a service call by a qualified service technician.
A. Standing Pilot Ignition System
Symptom
1. After repeated triggering
of the red or black piezo
ignitor button, the spark
ignitor will not light the
pilot.
2. The pilot will not stay lit
after carefully following
the lighting instructions.
Possible Causes
Corrective Action
A. No gas or low gas pressure.
Check the remote shut-off valves from the appliance. Usually, there
is a valve near the gas main. There can be more than one valve between the appliance and the main.
B. No lp in tank.
Check the LP (propane) tank. You may be out of fuel.
C. Ignitor.
Check the spark at the electrode and pilot. If no spark and electrode
wire is properly connected, replace the ignitor. Verify that there is no
short in electrode wire.
D. Pilot or misaligned electrode
(spark at electrode).
Using match, light the pilot. If the pilot lights, turn off the pilot and
trigger the piezo ignitor button again. If the pilot lights, an improper
gas/air mixture caused the bad lighting and a longer purge period is
recommended. If the pilot will not light, ensure the gap at the electrode and pilot is one-eighth in. to have a strong spark. If the gap is
OK, replace the pilot.
A. Thermocouple.
Check that the pilot flame impinges on the thermocouple. Adjust the
pilot for proper flame impingement.
Ensure that the thermocouple connection at the gas valve is fully inserted and tight (hand tighten plus 1/4 turn).
Verify proper voltage output from the thermocouple to the valve.
Place one millivolt meter lead wire on the thermocouple copper lead.
Place the second lead wire on the solder button on the back of the
valve (blue wire). Start the pilot and hold the valve knob in. The millivolt reading should read 8-16 millivolts. If millivolt reading is less
than 8 millivolts, replace thermocouple.
3. The pilot is burning,
there is no burner
flame, the valve knob is
in the ON position, and
the ON/OFF switch is in
the ON position.
B. Improper gas inlet pressure.
Natural gas should be 5-10 in. w.c. LP should be 11-13 in. w.c. Verify
pressure with manometer.
C. Valve.
If the thermocouple is producing 8-16 millivolts, replace control valve.
A. ON/OFF switch or wires.
Check the ON/OFF switch and wires for proper connections. Place
the jumper wires across the terminals at the ON/OFF switch. If the
burner comes on, replace the ON/OFF switch. If the ON/OFF switch
is OK, place the jumper wires across the ON/OFF switch wires at the
gas valve. If the burner comes on, the wires are faulty or connections
are bad.
B. Thermopile may not be generating sufficient millivoltage.
Check that the pilot flame impinges thermopile properly.
Be sure the wire connections from the thermopile at the gas valve
terminals are tight and that the thermopile is fully inserted into the
pilot bracket.
Check the thermopile with a millivolt meter. Take the reading at THTP&TP terminals of the gas valve. The meter should read 350 millivolts minimum, while holding the valve knob depressed in the pilot
position, with the pilot lit, and the ON/OFF switch in the OFF position.
Replace the thermopile if the reading is below the specified minimum.
With the pilot in the ON position, disconnect the thermopile leads
from the valve. Take a reading at the thermopile leads. The reading
should be 350 millivolts minimum. Replace the thermopile if the reading is below the minimum.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
67
Troubleshooting (continued)
Symptom
3. (Continued)
Possible Cause
Corrective Action
C. Valve.
Turn the valve knob to the ON position. Place the ON/
OFF switch in the ON position. Take a reading with a
millivolt meter at the thermopile terminals. The millivolt
meter should read greater than 125mV. If the reading
is acceptable, and if the burner does not come on, replace the gas valve.
D. Plugged burner orifice.
Check the burner orifice for stoppage. Remove stoppage.
E. Wall switch or wires.
Check the wall switch and wires for proper connections. Place the jumper wires across the terminals at
the wall switch. If the burner comes on, replace the
wall switch. If the wall switch is OK, place the jumper
wires across the wall switch wires at the gas valve. If
the burner comes on, the wires are faulty or connections are bad.
4. Frequent pilot outage A. Pilot flame may be too high or too low, or blowproblem.
ing out (high pressure), causing pilot safety to
drop out.
Clean thermocouple and adjust the pilot flame for
proper flame impingement. Follow lighting instructions
carefully.
5. The pilot and main
burner extinguish
while in operation.
A. No LP in tank.
Check the LP (propane) tank. Refill the fuel tank.
B. Improper gas inlet pressure.
Natural gas should be 5-10 in. w.c. LP should be 11-13
in. w.c. Verify pressure with manometer.
C. Inner vent pipe leaking exhaust gases back
into the system.
Check venting system for damage. Replace/repair improperly assembled pipe sections.
D. Glass installed improperly.
Check to ensure glass is installed properly. Replace
fixed glass panel assembly.
E. Thermopile or thermocouple.
Replace pilot if necessary.
F. Improper vent cap installation.
Check for proper installation and freedom from debris
or blockage.
A. Flame impingement.
Adjust the log set so that the flame does not excessively impinge on it. Refer to log instructions.
B. Improper air shutter setting.
Refer to manual for shutter set points. Ensure that set
point is correct for appliance/gas type. If unit has adjustable shutter, it may be necessary to increase shutter opening.
C. Debris around air shutter.
Inspect the opening at the base of the burner. NO MATERIAL SHOULD BE PLACED IN THIS OPENING.
A. Insufficient oxygen being supplied.
Ensure that the vent cap is installed properly and free
of debris. Ensure that the vent system joints are tight
and have no leaks.
6. Glass soots.
7. Flame burns blue
and lifts off burner.
Ensure that no debris has been placed at the base of,
or in the area of the air holes in the center of the base
pan beneath the burner.
Ensure that the glass is tightened properly on the unit,
particularly on top corners.
68
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
B. IntelliFire Plus™ Ignition System
Symptom
Possible Cause
1. Pilot won’t light.
A. Incorrect wiring.
The ignitor/module
makes noise, but no
B. Loose connections or electrical
spark.
shorts in the wiring.
2. Pilot won’t light,
there is no noise or
spark.
3. Pilot sparks, but
Pilot will not light.
4. Pilot lights but continues to spark, and
main burner will not
ignite. (If the pilot
continues to spark
after the pilot flame
has been lit, flame
rectification has not
occurred.)
Corrective Action
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are
connected to correct terminals on module and pilot assembly.
Verify no loose connections or electrical shorts in wiring from module to pilot assembly. Verify connections underneath pilot assembly
are tight; also verify igniter and flame sense wires are not grounding
out to metal chassis, pilot burner, pilot enclosure, mesh screen if
present, or any other metal object.
C. Ignitor gap is too large.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).
A. No power, transformer installed
incorrectly, or depleted batteries.
Verify that transformer is installed and plugged into module. Check
voltage of transformer at connection to module. Acceptable readings of a good transformer are between 6.4 and 6.6 volts DC. Battery power supply voltage must be at least 4 volts. If below 4 volts,
replace batteries.
B. A shorted or loose connection in
wiring configuration or wiring harness.
Remove and reinstall the wiring harness that plugs into module.
Verify there is a tight fit. Verify pilot assembly wiring to module. Remove and verify continuity of each wire in wiring harness. Replace
any damaged components.
C. Improper wall switch wiring.
Verify that 110-120 VAC power is “ON” to junction box.
D. Module not grounded.
Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
A. Gas supply.
Verify that incoming gas line ball valve is “open”. Verify that inlet
pressure reading is within acceptable limits.
B. Ignitor gap is too large.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).
C. Module is not grounded.
Verify module is securely grounded to metal chassis of appliance.
D. Pilot valve solenoid
Verify that 1.5 to 1.8 VDC is supplied to pilot solenoid from module.
If below 1.5 volts, replace module. If 1.5 volts or greater, replace
valve.
A. A shorted or loose connection in
flame sensing rod.
Verify all connections to wiring diagram in manual. Verify connections underneath pilot assembly are tight. Verify flame sense or igniter wires are not grounding out to metal chassis, pilot burner, pilot
enclosure or screen if present, or any other metal object.
B. Poor flame rectification or contaminated flame sensing rod.
With fixed glass assembly in place, verify that flame is engulfing
flame sensing rod on left side of pilot hood. Flame sensing rod
should glow shortly after ignition. With a multi-meter, verify that
current in series between module and sense lead is at least 0.14
microamps. Verify correct pilot orifice is installed and gas inlet is set
to pressure specifications. Polish flame sensing rod with fine steel
wool to remove any contaminants that may have accumulated on
flame sensing rod.
C. Module is not grounded.
Verify module is securely grounded to metal chassis of appliance.
Verify that wire harness is firmly connected to the module.
D. Damaged pilot assembly or contaminated flame sensing rod.
Verify that ceramic insulator around the flame sensing rod is not
cracked, damaged, or loose. Verify connection from flame sensing
rod to white sensor wire. Polish flame sensing rod with fine steel
wool to remove any contaminants that may have accumulated on
flame sensing rod. Verify continuity with a multi-meter with ohms set
at lowest range. Replace pilot if any damage is detected.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
69
16
Reference Materials
A. Appliance Dimension Diagram
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.
L
M
J
K
N
TOP VIEW
H
GAS LINE
ACCESS
R
I
C
D
G
O
E
Q
B
A
P
LEFT SIDE
F
RIGHT SIDE
FRONT VIEW
Location
Inches
Millimeters
Location
Inches
Millimeters
A
41
1041
J
21
533
B
36-1/8
918
K
11-11/16
297
C
33-1/2
851
L
28-1/2
724
D
34-5/8
879
M
14-1/4
362
E
2-1/4
57
N
8-1/2
216
F
9-11/16
246
O
2-7/8
73
8-1/2
216
G
26-7/8
683
P
H
6 dia
152
Q
1
25
I
39-7/8
1013
R
40-7/8
1038
Figure 16.1 Appliance Dimensions-6000 Models
70
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
L
M
J
K
N
TOP VIEW
H
GAS LINE
ACCESS R
I
C
D
G
E
Q
O
B
P
F
A
LEFT SIDE
RIGHT VIEW
FRONT VIEW
Location
Inches
Millimeters
Location
Inches
Millimeters
A
48
1219
J
21
533
B
43-1/8
1096
K
11-11/16
297
C
35-1/2
902
L
35-1/2
902
D
36-5/8
930
M
17-3/4
451
8-1/2
216
E
2-3/8
60
N
F
9-15/16
252
O
2-7/8
73
G
28-7/8
734
P
8-1/2
216
H
6
152
Q
1
25
I
41-7/8
1064
R
42-7/8
1089
Figure 16.2 Appliance Dimensions-8000 Models
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
71
B. Vent Components Diagrams
Effective Length
Pipe
Effective
Height/Length
DVP4
DVP Pipe (see chart)
Inches
Millimeters
4
102
DVP6
6
152
DVP12
12
305
DVP24
24
610
DVP36
36
914
DVP48
48
1219
DVP6A
3 to 6
76 to 152
DVP12A
3 to 12
76 to 305
10-1/2 in.
(267 mm)
45 °
4-7/8 in.
(124 mm)
10-7/8 in.
(276 mm)
DVP45 (45º Elbow)
11-3/8 in.
(289 mm)
10 in.
(254 mm)
1 in.
(25 mm)
20-3/4 in.
(527 mm)
7-3/8 in.
(187 mm)
1-1/4 in. (32 mm)
10 in.
(254 mm)
9-1/4 in.
(235 mm)
Tab=1 in.
(25.4 mm)
1/2 in. TYP
(13 mm)
13-1/4 in.
(337 mm)
Finished Height: 19-3/4 in./502 mm
UNIV-AS2 (Attic Insulation Shield)
DVP-FS (Ceiling Firestop)
DVP90ST (90° Elbow)
12 in.
(305 mm)
1- 1/2 in.
(38 mm)
10 in.
(254 mm)
UP
5 in.
(127 mm)
1 in.
(25 mm)
8 in.
(203 mm)
14 in.
(356 mm)
12 in.
(305 mm)
6 in.
(152 mm)
DVP-HVS (Vent Support)
DVP-WS (Wall Shield Firestop)
Figure 16.3 DVP vent components
72
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the
existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B
will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
Term Cap
12 in.
(305 mm)
DVP-TRAP
Horizontal Termination Cap
Max
Effective
Length
Trap1
Trap2
Minimum
Effective Length
Maximum
Effective Length
3-1/8 in.
4-5/8 in.
79 mm
117 mm
5-3/8 in.
9-3/8 in.
137 mm
238 mm
DVP-TRAP1
DVP-TRAP2
DVP-TRAPK1
DVP-TRAPK2
DVP-HPC1
DVP-HPC2
Figure 16.4 DVP vent components
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
73
B. Vent Components Diagrams (continued)
31 in.
(787 mm)
13-1/4 in.
(337 mm)
24-5/8 in.
(625 mm)
27-1/2 in.
(699 mm)
24-5/8 in.
(625 mm)
13-1/4 in.
(337 mm)
RF6M
Roof Flashing Multi-pak
RF12M
Roof Flashing Multi-pak
11-7/8 in.
(302 mm)
5 in.
(127 mm)
13-7/8 in.
(352 mm)
DVP-TRAPFL
Flashing
DVP-BEK2
DVP-HPC Cap Brick Extension
11-5/8 in.
(295 mm)
12-1/8 in.
(308 mm)
7-1/8 in.
(181 mm)
5-3/4 in.
(146 mm)
13-7/8 in.
(352 mm)
26 in.
660 mm
DVP-HSM-B
Extended Heat Shield
Figure 16.5 DVP vent components
74
COOL-ADDM
Cap Shield
9-1/2 in.
(241 mm)
14 in.
(356 mm)
DRC-RADIUS
Cap Shield
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
B. Vent Components Diagrams (continued)
7-3/8 in.
(187 mm)
1-1/2 in.
(38 mm)
17-3/4 in.
(451 mm)
14 in.
(356 mm)
LINK-DV-30B
(LINK-DV-30)
12 in.
(305 mm)
12 in.
305 mm
DVP-TB1
BasementVent Cap
7-1/4 in.
(184 mm)
12-1/2 in.
(318 mm)
5-1/4 in.
(133 mm)
DVP-TVHW
VerticalTermination Cap (Highwind)
PVK-80
(Not compatible with Intellifire Plus™.)
(For use with IPI and DSI appliances only.)
14 in.
(356 mm)
16-7/8 in.
(429 mm)
12 in.
(305 mm)
7-1/8 in.
(181 mm)
12-1/8 in.
(314 mm)
8-3/4 in.
(222 mm)
1 in.
(25 mm)
7-1/4 in.
(184 mm)
14 in.
(356 mm)
3/8 in. (10 mm)
1 in. (25 mm)
7-3/4 to 10-3/8 in.
(197 to 264 mm)
1-5/8 in.
(41 mm)
DVP High Performance Cap
DVP-FBHT
FireBrickTermination Cap
Figure 16.6 DVP vent components
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
75
Optional Wire Harness
13-5/8 in.
346 mm
DESCRIPTION
12-1/2 in.
318 mm
PART NUMBER
10 ft. PV Wire Harness
PVI-WH10
20 ft. PV Wire Harness
PVI-WH20
40 ft. PV Wire Harness
PVI-WH40
60 ft. PV Wire Harness
PVI-WH60
80 ft. PV Wire Harness
PVI-WH80
100 ft. PV Wire Harness
PVI-WH100
20-3/4 in.
527 mm
Note: Wire harnesses required to power the PVI-SLP
connect to the appliance and are ordered separately
from PVI-SLP. Contact your dealer to order.
PVI-SLP
Power Vent Inline
Note: Use only approved termination caps with the
PVI-SLP. See instructions included with PVI-SLP kit.
16 in.
406 mm
9-3/16 in.
(233 mm)
13-5/8 in.
(346 mm)
15 in.
(381 mm)
4-1/2 in.
114 mm
16-11/16 in.
424 mm
12-1/2 in.
(318 mm)
SLP-LPC
SLP Low Profile Cap
76
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
16-11/16 in.
(424 mm)
B. Vent Components Diagrams (continued)
8-1/8 in.
(206 mm)
13 in.
(330 mm)
Effective Length
5-3/4 to 8-3/8 in.
146 to 213 mm
5-1/2 in.
140 mm
87°
8-3/8 in.
213 mm
3°
15 in.
(381 mm)
10-1/2 in.
267 mm
10-7/8 in.
276 mm
WARNING
Fire Risk.
• When using DVP-HRC-SS and DVP-HRC-ZCSS termination caps on top vented fireplaces, a
6 inch minimum vertical vent section is required
before installing first elbow.
DVP-HRC-SS
DVP-HRC-ZC-SS
HORIZONTAL TERMINATION CAP
COAXIAL to COLINEAR VENTING
LINK-DV30B
Flex Liner Kit
Figure 16.7 DVP vent components
768-380A
Stainless Steel Flex Pipe
DV-46DVA-GCL
Coaxial/Colinear Appliance Connector
DVP-2SL
Adapter
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
77
B. Vent Components Diagrams (continued)
6-1/2 in.
165 mm
6-1/2 in.
165 mm
8-3/4 in.
222 mm
6-1/2 in.
165 mm
9-1/4 in.
235 mm
6 in.
152 mm
6-5/8 in.
168 mm
SLP45
45° Elbow
6-5/8 in.
168 mm
9-7/8 in.
251 mm
SLP90
90° Elbow
Effective
Height/
Length
6-1/2 in.
165 mm
Effective Height/Length
SLP PIPE
10-7/8 in.
276 mm
Pipe
inches
mm
SLP4
4
102
SLP6
6
152
SLP12
12
305
SLP24
24
610
SLP36
36
914
SLP48
48
1219
SLP6A
2-6
51 - 152
SLP12A
2 - 12
51 - 305
25-3/16 in.
640 mm
8-1/16 in.
205 mm
1-1/2 in.
38 mm
8-7/8 in.
225 mm
DVP-SLP24
Adapter
SLP-HVS
Horizontal Pipe
Support
8-11/16 in.
220 mm
8-11/16 in.
220 mm
12 in.
305 mm
1-1/2 in.
38 mm
12 in.
305 mm
SLP-WS
Wall Shield Firestop
SLP-FS
Ceiling Firestop
Figure 16.8 SLP Series Vent Components
78
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
5-1/2 in.
146 mm
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm)
the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a
DVP-HSM-B will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
Term Cap
Max
Effective
Length
12 in.
(305 mm)
SLP-TRAP
Horizontal Termination Cap
Trap1
Trap2
Minimum
Effective Length
Maximum
Effective Length
3-1/8 in.
4-3/4 in.
79 mm
121 mm
5-1/4 in.
9-1/4 in.
133 mm
235 mm
4-3/16 in.
106 mm
6-3/8 in.
163 mm
4-5/8 in.
117 mm
4 in.
102 mm
5-1/16 in.
128 mm
8-1/8 in.
206 mm
DVP-2SL
Adapter
14-7/16 in.
367 mm
26 in.
660 mm
2-5/16 in.
59 mm
14-7/16 in.
367 mm
DVP-HSM-B
Extended Heat Shield
SLP-WT-BK
Wall Thimble-Black
Figure 16.9 SLP Series Vent Components
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
79
B. Vent Components Diagrams (continued)
13 in.
330 mm
14 in.
356 mm
1-5/16 in.
34 mm
13 in.
330 mm
10-9/16 in.
269 mm
SLP-CCS-BK
Cathedral Ceiling
Support Box-Black
SLP-DCF-BK
Ceiling Firestop
Black
10-11/16 in.
271mm
12 in.
305 mm
28-1/2 in.
724 mm
12-1/2 in.
318 mm
13-1/2 in.
343 mm
SLK-SNKD
Snorkel
Termination Cap
SLP-TVHW
Vertical
Termination Cap
Figure 16.10 SLP Series Vent Components
80
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
6000C, 6000C-IPI
C. Service
Parts
Service
Parts
36” Gas Fireplace - DV
Beginning Manufacturing Date: Aug 2009
Ending Manufacturing Date: Active
Log Set Assembly
7
1
2
4
6
5
8
3
15
14
9
10
13
9.1
11
12
16
9.2
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and
Home Technologies does not sell directly to consumers. Provide model number and serial number when
requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Y
Log Set Assembly
LOGS-6C
1
Log 1
SRV2164-701
2
Log 2
SRV2164-702
3
Log 3
SRV2164-703
4
Log 4
SRV2164-704
5
Log 5
SRV2164-705
6
Log 6
SRV2164-706
7
Insulation Board
2166-136
8
Burner Top
SRV2166-100
Y
Burner NG
2164-007
Y
Burner LP
2164-008
Y
9
9.1
Air Scoop
2170-188
9.2
Pilot Cover
2170-181
10
Log Grate
2166-104
11
Base Refractory
SRV6BASE-STRAT
12
Refractory Basket
2166-108
13
Glass Door Assembly
GLA-6000G
14
Surround Assembly
2166-019
15
Finishing Strips (Sold as kit only)
SRVFS-6
16
Junction Box
4021-013
Additional service part numbers appear on following page.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
Y
Y
4/14
81
8000C, 8000C-IPI
Service Parts
Beginning Manufacturing Date: Aug 2009
Ending Manufacturing Date: Active
42” Gas Fireplace - DV
7
Log Set Assembly
1
2
4
8
3
6
5
15
14
10
13
9
9.1
11
12
16
9.2
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and
Home Technologies does not sell directly to consumers. Provide model number and serial number when
requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
LOGS-8C
1
Log 1
SRV2168-701
2
Log 2
SRV2168-702
3
Log 3
SRV2168-703
4
Log 4
SRV2168-704
5
Log 5
SRV2168-705
6
Log 6
SRV2168-706
7
Insulation Board
2170-136
8
Burner Top
SRV2170-100
Y
Burner NG
2168-007
Y
Burner LP
2168-008
Y
9
9.1
Air Scoop
2170-188
9.2
Pilot Cover
2170-181
10
Log Grate
2170-104
11
Base Refractory
SRV8BASE-STRAT
12
Refractory Basket
2170-108
13
Glass Door Assembly
GLA-950TR
14
Surround Assembly
2170-019
15
Finishing Strips (Sold as kit only)
SRVFS-8
16
Junction Box
4021-013
Additional service part numbers appear on following page.
82
Y
Log Set Assembly
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
Y
Y
3/14
6000C-IPI, 8000C-IPI
Service Parts
Beginning Manufacturing Date: Aug 2009
Ending Manufacturing Date: Active
#17 Valve Assembly
17.2
17.1
17.14
17.3
17.15
17.13
17.12
17.4
17.11
17.7
17.5
17.6
17.10
17.9
17.8
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and
Home Technologies does not sell directly to consumers. Provide model number and serial number when
requesting service parts from your dealer or distributor.
ITEM
17.1
17.2
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Shutter Bracket Assembly
2166-157
Y
Pilot Assembly NG
2166-370
Y
Pilot Assembly LP
2166-371
Y
SRV485-301
Y
Pilot Tube
17.3
3-hole Grommet
2118-420
17.4
Valve Bracket
2118-104
17.5
Flex Ball Valve Assembly
302-320A
Y
Valve NG
2166-302
Y
Valve LP
2166-303
Y
303-315/5
Y
17.6
17.7
Male Connector
17.8
Bulkhead W/Tube
2166-119
Y
17.9
Jumper Wire
2187-198
Y
17.10
Battery Pack **
2166-323
Y
17.11
Thermostat Wire Assembly
2118-170
Y
17.12
Transformer
2326-131
Y
17.13
Control Assembly
2164-030
Y
Pkg of 5
17.14
Module
2166-307
Y
17.15
Wire Harness
2166-304
Y
582-837
Y
582-852
Y
582-833
Y
582-850
Y
Burner Orifice NG (#37C)
Burner Orifice LP (#52C)
Burner Orifice NG (#33C)
Burner Orifice LP (#50C)
6000C-IPI
8000C-IPI
**Fuse for battery pack can be sourced locally, not a warranty item. Specs are 250v, 1A fuse, 3/4" long
Additional service part numbers appear on following page.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
83
6000C, 8000C
Service Parts
Beginning Manufacturing Date: Aug 2009
Ending Manufacturing Date: Jan 2010
#17 Valve Assembly
17.1
17.2
17.3
17.4
17.5
17.10
17.6
17.8
17.9
17.7
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and
Home Technologies does not sell directly to consumers. Provide model number and serial number when
requesting service parts from your dealer or distributor.
ITEM
17.1
17.2
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Shutter Bracket Assembly
2166-157
Y
Pilot Assembly NG
2103-010
Y
Pilot Assembly LP
2103-011
Y
Pilot Tube
SRV485-301
Y
Thermopile
2103-512
Y
Thermocouple
2103-511
Y
17.3
3-hole Grommet
2118-420
17.4
Valve Bracket
2118-104
17.5
Flex Ball Valve Assembly
302-320A
Y
17.6
Piezo Ignitor
291-513
Y
Valve NG
2166-300
Y
Valve LP
2166-301
Y
17.7
17.8
Male Connector
303-315/5
Y
17.9
Bulkhead W/Tube
Pkg of 5
2166-119
Y
17.10
Thermostat Wire Assembly
2045-024
Y
582-837
Y
582-852
Y
582-833
Y
582-850
Y
Burner Orifice NG (#37C)
Burner Orifice LP (#52C)
Burner Orifice NG (#33C)
Burner Orifice LP (#50C)
Wire Assembly
6000C
8000C
040-557A
Additional service part numbers appear on following page.
84
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
6000C, 8000C
Service Parts
Beginning Manufacturing Date: Aug 2009
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and
Home Technologies does not sell directly to consumers. Provide model number and serial number when
requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Exhaust Shield
385-105
Flue Restrictor
385-128
Gasket Assembly
Contains Vent, Burner Neck, Valve Plate, LED and Adjustable Air Shutter Gaskets
Glass Latch Support
Pkg of 2
2166-081
33858/2
Mineral Wool
050-721
Touch Up Paint
TUP-GBK-12
Y
Standing Pilot Conversion Kits
Conversion Kit NG
6000C
Conversion Kit LP
Conversion Kit NG
8000C
NGKS-6C
Y
LPKS-6C
Y
NGKS-8C
Y
LPKS-8C
Y
Regulator NG
NGK-SITV-50
Y
Regulator LP
LPK-SITV-50
Y
Pilot Orifice NG
2103-116
Y
Pilot Orifice LP
2103-117
Y
NGKI-6C
Y
LPKI-6C
Y
Conversion Kit LP
IPI Conversion Kits
Conversion Kit NG
6000C-IPI
Conversion Kit LP
NGKI-8C
Y
LPKI-8C
Y
Regulator NG
NGK-DXV-50
Y
Regulator LP
LPK-DXV-50
Y
Pilot Orifice NG
593-528
Y
Pilot Orifice LP
593-527
Y
Conversion Kit NG
8000C-IPI
Conversion Kit LP
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14
85
D. Contact Information
Heat & Glo, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.heatnglo.com
Please contact your Heat & Glo dealer with any questions or concerns.
For the location of your nearest Heat & Glo dealer,
please visit www.heatnglo.com.
- NOTES ________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
This product may be covered by one or more of the following patents: (United States) 5601073, 5613487, 5647340,
5890485, 5941237, 6006743, 6019099, 6053165, 6145502, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122,
7098269, 7258116, 7470729, 8147240 or other U.S. and foreign patents pending.
2000-945B
Printed in U.S.A. - Copyright 2014
86
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. V • 4/14