Hanns.G HG281DJ Monitor User Guide Manual Operating Instructions

HG281
HSG1040
User’s Manual
Before operating the monitor, please read this manual thoroughly. This manual should be retained for
future reference.
FCC Class B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
The device complies with Parts 15 of the FCC Rule. Operation is subject to the following two
conditions﹕(1) this device may not cause harmful interference﹔and (2) this device must accept any
interference received, including interference that may cause undesired operations.
CANADA
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulation.
This device complies with requirement of EMC directive 89/336/EEC with regard to
Electromagnetic Compatibility, and 73/23/EEC and 93/68/EEC with regard to Low Voltage directive.
Socket-outlet shall be near the equipment and shall be accessible.
2
User’s Manual
Congratulations!
The product you have just purchased carries the TCO’06 Media
Displays label. This means that your display is designed and
manufactured according to some of the strictest performance and
environmental criteria in the world. The manufacturer of this display
has selected it to be certified to TCO’06 Media Displays as a sign of
usability, high performance and reduced impact on the natural
environment.
Products certified to TCO´06 Media Displays are specifically designed for high quality reproduction
of moving images. Features such as luminance, color rendition and response time are important
when watching TV or working with media, graphics, web design and other applications that demand
outstanding moving images. *
Other features of TCO’06 Media Displays :
Ergonomics
•
Good visual ergonomics and image quality in order to reduce vision and strain problems. Criteria
for luminance, contrast, resolution, reflectance, color rendition and response time.
Energy
•
•
Energy saving mode – beneficial both for the user and the environment
Electrical safety
Emissions
•
Low electromagnetic fields surrounding the display
Ecology
•
•
Product is designed for recycling. Manufacturer must have a certified environmental
management system such as EMAS or ISO 14 001
Restrictions on
o Chlorinated and brominated flame retardants and polymers
o Hazardous heavy metals such as cadmium, mercury, hexavalent chromium and lead.
All TCO labelled products are verified and certified by TCO Development, an independent third
party labelling organization. For over 20 years, TCO Development has been at the forefront of
moving the design of IT equipment in a more user-friendly direction. Our criteria are developed in
collaboration with an international group of researchers, experts, users and manufacturers. Since the
program’s inception, TCO labelled products have grown in popularity and are now requested by
users and IT-manufacturers all over the world.
Full specifications and lists of certified products can be found on our homepage –
www.tcodevelopment.com
* For a display used primarily for conventional work tasks such as word processing, we recommend a display certified to
our office display series TCO’03 Displays or later version.
3
User’s Manual
Recycling Information
We, the Hanns.G care very much about our environment protection strategy and firmly believe that
it helps us have healthier earth via appropriate treatment and recycling of industrial technology
devices at the end-of-life.
These devices contain recyclable materials, which can be re-decomposed and re-integrated into
brand-new marvels. On the contrary, other material can be classified to hazardous and poisoned
substances. We strongly encourage you to contact the provided information to recycle this product.
For more information, please visit
www.hannsg.com
4
User’s Manual
TABLE OF CONTENTS
SAFETY NOTICE ......................................................................................................6
PRECAUTIONS.....................................................................................................6
SPECIAL NOTES ON LCD MONITORS ..........................................................7
BEFORE OPERATING THE MONITOR ...............................................................8
FEATURES.............................................................................................................8
CHECKING THE CONTENTS OF THE PACKAGE ......................................8
INSTALLATION INSTRUCTIONS ....................................................................9
POWER...................................................................................................................9
MAKING CONNECTIONS................................................................................10
ADJUSTING THE VIEWING ANGLE.............................................................12
OPERATING INSTRUCTIONS .............................................................................13
GENERAL INSTRUCTIONS.............................................................................13
FRONT PANEL CONTROL ..............................................................................14
HOW TO ADJUST A SETTINGS ......................................................................15
PLUG AND PLAY................................................................................................18
TECHNICAL SUPPORT (FAQ) .............................................................................19
Q & A FOR GENERAL PROBLEMS ...............................................................19
ERROR MESSAGE & POSSIBLE SOLUTIONS ...........................................21
APPENDIX ................................................................................................................22
SPECIFICATIONS ..............................................................................................22
5
User’s Manual
SAFETY NOTICE
1. The changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the
emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modification to this equipment. It is the responsibilities of the user to correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously high
voltages are present inside the monitor. Do not open the cabinet. Refer servicing to qualified
personnel only.
PRECAUTIONS
• Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub,
•
•
•
•
•
•
•
•
swimming pool or in a wet basement.
Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a
person and cause serious damage to the appliance. Use only a cart or stand recommended by the
manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a
mounting kit approved by the manufacturer and follow the kit instructions.
Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure
reliable operation of the monitor and to protect it from overheating, be sure these openings are not
blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place
the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or
cabinet unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated on the label. If you
are not sure of the type of power supplied to your home, consult your dealer or local power
company.
Unplug the unit during a lighting storm or when it will not be used for long period of time. This
will protect the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a
fire or electric shock. Never spill liquids on the monitor.
Do not attempt to service the monitor by yourself; opening or removing covers can expose you to
dangerous voltages and other hazards. Please refer all servicing to qualified service personnel.
The wall socket shall be installed near the equipment and shall be easily accessible.
6
User’s Manual
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a problem.
• Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the
Power Switch and then turn it on again to make sure the flicker disappears.
• You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
• The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or
less such as a missing pixel or a pixel lit all of the time.
• Due to the nature of the LCD screen, an afterimage of the previous screen may remain after
switching the image, when the same image is displayed for hours. In this case, the screen is
recovered slowly by changing the image or turning off the Power Switch for hours.
• If the screen suddenly flashes erratically or the backlighting fails, please contact your dealer or
service center for repair. Do not attempt to repair the monitor yourself.
Lamp Disposal
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR
DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE
INFORMATION, CONTACT THE ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG.
FOR LAMP SPECIFIC DISPOSAL INFORMATION CHECK TTTTWWW.LAMPRECYCLE.ORG.
7
User’s Manual
BEFORE OPERATING THE MONITOR
FEATURES
•
•
•
•
•
•
28” Wide screen TFT Color LCD Monitor
Crisp, Clear Display for Windows
Recommended Resolutions: 1920 X 1200@60Hz
EPA ENERGY STAR®
Ergonomic Design
Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
LCD Monitor
Cables and User manual
Power Cord
VGA Cable
Audio Cable
HDMI to DVI-D Cable
(Optional)
D-sub to YPbPr Cable
(Optional)
3.5mm Mini Jack to R/L Cable
(Optional)
User’s manual
Warranty card
Screw X 3 & Allen key
8
User’s Manual
INSTALLATION INSTRUCTIONS
INSTALL
REMOVE
Figure.1. Installing and Removing the Base
INSTALLATION:
1.
2.
3.
4.
5.
Turn the monitor over and set it upside down.
Align the monitor to the slots on the stand.
Please note that the longer edge of the stand should be facing forward.
Securely mount the monitor onto the stand using the supplied screws and Allen key.
Check the underside of the stand to ensure that the monitor has been firmly installed to the stand
and that the screws do not loosen.
6. Please keep the Allen (hex) key.
REMOVAL:
1. Turn the monitor over and set it upside down.
2. Loosen the screws by turn them counterclockwise, using the supplied Allen key.
3. Detach the stand from the monitor.
POWER
POWER SOURCE:
1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an Internal universal power supply that allows operation with either
100/120V AC or 220/240V AC voltage areas (No user adjustment is required.)
3. Connect one end of the AC-power cord to your LCD monitor’s AC-input socket, and the other
end to the wall-outlet.
9
User’s Manual
MAKING CONNECTIONS
CONNECTING TO A PC
Turn off your computer before performing the procedure below.
1. Connect one end of the D-Sub cable to the back of the monitor and connect the other end to the
computer’s D-Sub port.
2. Connect one end of the HDMI to DVI-D cable (Dual input mode optional) to the back of the
monitor and connect the other end to the computer’s DVI-D port.
3. Connect the audio cable between the monitor's audio input and the PC's audio output (green
port).
4. Plug one end of the AC power cord to the LCD monitor’s AC input socket, and the other end to
the Wall outlet.
5. Turn on your monitor and computer.
Figure.2 Connecting to a PC
1.
3.
5.
Power AC Input
VGA Input
Earphone
2.
4.
10
HDMI Input
Audio Input
User’s Manual
CONNECTING TO A A/V DEVICE:
Connect A/V devices via the D-sub and Audio Line in connectors at the back of the monitor.
1. Connect one end of the D-Sub cable to the back of the monitor and connect the other end to the
D-sub to YPbPr adapter cable.
2. Connect the Y (green) connector on the D-sub to YPbPr adapter cable to the Y output connector
on the A/V device.
3. Connect the Pb (blue) connector on the D-sub to YPbPr adapter cable to the Pb/Cb output
connector on the A/V device.
4. Connect the Pr (red) connector on the D-sub to YPbPr adapter cable to the Pr/Cr output on the
A/V device.
5. Connect the 3.5mm mini jack to R/L adapter cable to the audio output connector of the A/V
device and the other end to the audio input connector at the back of the monitor.
6. Turn on your monitor and A/V device.
Figure 3: Connecting A/V Devices
11
User’s Manual
ADJUSTING THE VIEWING ANGLE
• For optimal viewing it is recommended to look at the full face of the monitor, and then adjust the
monitor’s angle to your own preference.
• Hold the stand so you do not topple the monitor when you change the monitor’s angle.
• You may adjust the monitor for a viewing angle of 0° to 20° vertically and 0° to 30°horizontally.
Figure.4. Monitor Angle
NOTES:
• Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD
screen.
• Be careful not to place fingers or hands near the hinges when tilting the monitor, otherwise
pinching can result.
12
User’s Manual
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons are located on the
front panel of the monitor (See Figure 5). By changing these settings, the picture can be adjusted to
your personal preference.
• The power cord should be connected.
• Connect the Signal cable from the monitor to the VGA card.
• Press the power button to turn on the monitor. The power indicator will light up.
Figure.5. Control Panel Buttons
CONTROL PANEL BUTTONS:
1.
Menu / Return
2.
Input source change / Enter
3.
5.
Brightness adjustment button /▲ [+]
Power Button
4.
6.
Volume adjustment button / ▼ [-]
Power Indicator
13
User’s Manual
FRONT PANEL CONTROL
• Power Button:
Press this button to switch ON/OFF monitor’s power.
• Power Indicator:
Blue
— Power On mode.
Orange — Power Saving mode.
• MENU / RETURN:
1. Turn the OSD menu on/off or return to the previous menu.
2. Exit OSD menu when in volume OSD status.
• Adjust ▲▼:
1. Adjust Brightness and volume when the OSD is off.
2. Navigate through adjustment icons when OSD is ON or adjust a function when function is
activated.
• i Button:
1. Press the i button to select the input signal type. (There are VGA, HDMI, YpbPr options
available but what port you can actually select depends on your model.)
2. The OSD menu is used as “confirmation” function during start-up.
3. Press and hold this button more than 3 seconds will start 「Auto Adjust」 function when using
VGA input only. (The auto adjustment function is used to optimize the 「horizontal position」,
「vertical position」,「clock」,and 「phase」.)
NOTES:
• Do not install the monitor in a location near heat sources such as radiators or air dusts, or in a
place subject to direct sunlight, or excessive dust or mechanical vibration or shock.
• Save the original shipping box and packing materials, as they will come in handy if you ever have
to ship your monitor.
• For maximum protection, repackage your monitor as it was originally packed at the factory.
• To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be
removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents
such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety
precaution, always unplug the monitor before cleaning it.
14
User’s Manual
HOW TO ADJUST A SETTINGS
BRIGHTNESS/CONTRAST
BRIGHTNESS
Adjust the brightness value of the display according to your
preference. Select「BRIGHTNESS」option to adjust the
brightness value.
CONTRAST
Adjust the contrast value of the display according to your
preference. Select「CONTRAST」option to adjust the contrast
value.
X-CONTRAST
Optimal setting for high contrast images or videos. The dark and
light areas of the image are automatically detected, and the
contrast is enhanced to provide a clearer, sharper image. Also,
you may select the「X-CONTRAST」option.
INPUT SETTING
INPUT SETTING
Select the 「INPUT SETTING」option to change between analog
(VGA) or Digital (HDMI) source. Enter the option and select
Analog or Digital. [Dual input mode optional]
AUTO SEARCH
From the Signal Selection menu, select the 「AUTO SEARCH」
option to activate or deactivate the automatic signal search
function.
COLOR SETTING
WARM
NATURE
COOL
Adjust the color temperature value of the display according to
your preference: WARM /NATURE/ COOL.
USER
Move the cursor to the User option and select it,
To adjust the red, enter the「R」option and adjust the level.
To adjust the green, enter the「G」option and adjust the level.
To adjust the blue, enter the「B」option and adjust the level.
IMAGE SETTING
AUTO ADJUST
The auto adjustment function is used to optimize the 「horizontal
position」, 「vertical position」,「clock」,and 「phase」. [For
VGA Input only]
ASPECT RATIO
When the aspect ratio of screen is distorted, you may make
adjustments by using this function. “FULL” indicates full screen
display, which does not ensure the image is shown as is or in
initial scale. “FIT” indicates scaling by the proportion of original
images, which may cause the screen showing black bands. [The
availability of this function depends upon the selected model]
15
User’s Manual
H-POSITION
Select the 「H-POSITION」option to shift the screen image to the
left or right. Enter the option and adjust the level. [For VGA
only]
V-POSITION
Select the 「V-POSITION」option to shift the screen image up or
down. Enter the option and adjust the level. [For VGA only]
CLOCK
Select the 「CLOCK」option to reduce the vertical flicker of
characters on the screen. Enter the option and adjust the level.
[For VGA only]
PHASE
Select the「PHASE」option to reduce the horizontal flicker of
characters on the screen. Enter the option and adjust the level.
[For VGA only]
SHARPNESS
Select the「SHARPNESS」option to adjust the sharpness of the
display. Set the value from -2 to 2.
HDMI MODE
Transferring audio-video image by HDMI port would
cause edges of the image being cut on the screen; select「PC
Mode」to display in full screen. Enter the option and select
「VIDEO Mode」(VIDEO) or 「PC Mode」(PC). [For HDMI
Input only]
OSD SETTING
LANGUAGE
Select 「LANGUAGE」 option to change the language of the
OSD. Enter the option and select a language. [Reference only,
the OSD Language depends on the selected model]
H-POSITION
Select 「H-POSITION」option to adjust the horizontal position of
the OSD. Enter the option and adjust the level.
V-POSITION
Select 「V-POSITION」option to adjust the vertical position of
the OSD. Enter the option and adjust the level.
TRANSPARENCY
Select 「TRANSPARENCY」option to adjust the transparency of
the OSD. Enter the option and adjust the level.
OSD TIME-OUT
Select 「OSD TIME-OUT」option to set the OSD time out from
10 to 100 seconds. Enter the option and adjust the level.
OSD COLOR
To choose the color combination of the OSD window, select
「OSD COLOR」option under 「OSD SETTING」menu, choose
modes 1/2/3.
16
User’s Manual
SYSTEM
AUDIO INPUT
While transferring via the HDMI port, it is recommended to set
AUDIO INPUT to HDMI; if no sound is outputted, it is
recommended to select AUDIO INPUT as PC, and make sure the
PC audio output cable is connected to monitor’s LINE IN (or
AUDIO IN) port. [For HDMI Input only]
VOLUME
Select the 「VOLUME」option to change the volume level. Enter
the option and adjust the level.
MUTE
Select the「MUTE」option to switch the function On or Off.
DDC/CI
Select the 「DDC/CI」option to switch the function On or Off.
[Dual input mode optional]
FACTORY RESET
Select the 「FACTORY RESET」option to reset to the monitor’s
default setting. This will erase the current settings. Enter the
option and select On or Off.
INFORMATION
Display Horizontal frequency/Vertical frequency/Resolution
information.
17
User’s Manual
PLUG AND PLAY
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD.
It allows the monitor to inform the host system of its identity and, depending on the level of DDC
used, communicate additional information about its display capabilities. The DDC2B is a
bidirectional data channel based on the I²C protocol. The host can request EDID information over the
DDC2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO
INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE
MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video Electronics Standards
Association (VESA) and/or the United States Environmental Protection Agency (EPA) and The
Swedish Confederation Employees (NUTEK). This feature is designed to conserve electrical energy
by reducing power consumption when there is no video-input signal present. When there is no video
input signal this monitor, following a time-out period, will automatically switch to power saving
mode. This reduces the monitor's internal power supply consumption. After the video input signal is
restored, full power is restored and the display is automatically redrawn. The appearance is similar to
a "Screen Saver" feature except the display is completely off. The display is restored by pressing a
key on the keyboard, or clicking the mouse.
18
User’s Manual
TECHNICAL SUPPORT (FAQ)
Q & A FOR GENERAL PROBLEMS
PROBLEM & QUESTION
POSSIBLE SOLUTION
Power LED is not on
*Check if the Power Switch is in the ON position
*Power Cord should be connected
No Plug & Play
*Check if the PC system is Plug & Play compatible
*Check if the Video Card is Plug & Play compatible
*Check if any plug pins on the VGA or HDMI connector are
bent
The display is too dark or too
bright.
*Adjust the Contrast and Brightness Controls.
Picture bounces or a wave
pattern is present in the picture
*Move electrical devices that may cause electrical interference.
The power LED is ON
(orange) but there’s no video
or no picture.
*Computer Power Switch should be in the ON position.
*Computer Video Card should be snugly seated in its slot
*Make sure monitor’s video cable is properly connected to the
computer.
*Inspect monitor’s video cable and make sure none of the pins
are bent.
*Make sure computer is operational by hitting the CAPS LOCK
key on the keyboard while observing the CAPS LOCK LED.
The LED should either turn ON or OFF after hitting the CAPS
LOCK key.
Missing one of the primary
colors (RED, GREEN, or
BLUE)
*Inspect the monitor’s video cable and make sure that none of
the pins are bent.
Screen image is not centered or * Adjust pixel frequency CLOCK and PHASE or press hot-key
sized properly.
(i Button)
Horizontal or vertical
disturbances on the screen
*Use win 95/98/2000/NT/ME/XP shutdown mode Adjust
CLOCK and PHASE or perform hot- key (i Button).
The screen resolution needs to
be adjusted
*Use win 2000/ME/XP Right click anywhere on desktop and
select Properties>Settings>Screen Resolution. Use the silder
to adjust the reslution and click Apply
No sound is outputted from
monitor’s built-in speaker
*To screen’s LINE IN port.
*Make sure the sound volume adjustment can be clearly
identified.
*Make sure the System > Silence option in the monitor menu is
on.
*While tto monitor’s LINE IN (or AUDIO IN) port.
19
User’s Manual
No sound is outputted from
monitor’s built-in speaker
*Make sure PC audio output cable is connected to screen's
LINE IN port (or AUDIO IN port).
*Make sure the sound volume adjustment can be clearly
identified.
*Make sure the System > Silence option in the monitor menu is
on.
*While transferring via HDMI port but no sound is outputted, it
is recommended to select AUDIO INPUT as a PC option, and
make sure PC audio output cable is connected to monitor's
LINE IN port(or AUDIO IN port). [For HDMI Input only]
20
User’s Manual
ERROR MESSAGE & POSSIBLE SOLUTIONS
CABLE NOT CONNECTED:
1. Check that the signal-cable is properly connected, If the connector is loose, tighten the
connector’s screws.
2. Check the signal-cable’s connection pins for damage.
INPUT NOT SUPPORT:
Your computer has been set to unsuitable display mode, set the computer to display mode given
in the following table.
RECOMMENDED AND SUPPORTED TIMING MODE:
(Analog / Digital mode)
MODE
RESOLUTION
REMARK
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
640x480@60 Hz
640x480@67 Hz
640x480@72 Hz
640x480@75 Hz
720x400@70 Hz
800x600@72 Hz
800x600@75 Hz
832x624@74.5 Hz
1024x768@60 Hz
1024x768@70 Hz
1024x768@75 Hz
1280x720@60 Hz
1280x1024@60 Hz
1280x1024@75 Hz
1440x900@60 Hz
1600x1200@60 Hz
1680x1050@60 Hz
1920x1200@60 Hz
VGA
MAC
VGA
VGA
VGA
SVGA
SVGA
MAC
XGA
XGA
XGA
SXGA
SXGA
SXGA
WXGA+
UXGA
WSXGA+
WUXGA
MODE
RESOLUTION
1
720x480i@60 Hz
2
720x480p@60Hz
3
720x576i@50Hz
4
720x576p@50Hz
5
1280x720p@50Hz
6
1280x720p@60Hz
(YPbPr mode)
7
1920x1080i@60Hz
8
1920x1080p@60Hz
9
1920x1080i@50Hz
10
1920x1080p@50Hz
We ensure that the monitor can be lighted under interlace signal mode, but we can not guarantee the
image quality.
21
User’s Manual
APPENDIX
SPECIFICATIONS
LCD Panel
Video
Driving system
TFT Color LCD
Size
28” (27.5" viewable)
Pixel pitch
0.309mm(H) x 0.309mm(V)
H-Frequency
24KHz – 80KHz
V-Frequency
56Hz– 75Hz
Display Colors
16.7M Colors
Max. Resolution
WUXGA 1920 x 1200 @60Hz
Plug & Play
VESA DDC2BTM
EPA ENERGY STAR
®
ON Mode
≤64.5W
Power Saving Mode
≤2W
OFF Mode
≤1W
Audio output
Rated Power 2.5 W rms (Per channel)
Input Terminal
VGA
HDMI (support DVI-D signal)
Maximum Screen Size
Hor. : 593.28mm
Ver. : 370.8mm
Power Source
100~240VAC±10%,50±3Hz,60±3Hz
Environmental
Considerations
Operating Temp: 5° to 35°C
Storage Temp.: -20° to 60°C
Operating Humidity: 10% to 85%
Dimensions
668(W)×486(H)×211(D) mm
26.3”(W)×19.1”(H)×8.3”(D)
Weight (NW)
10.8kg (23.8 lb)
***The above specification is subject to actual product specification and is subject to change without
prior notice.
NOTES:
The Maximum Resolution will depends on the display card supporting. Related issue can refer to
www.hannsg.com FAQ section.
22