Samsung - DVD Disc Player Disc User Guide Manual

DVD Player
DVD-P280K
www.samsung.com/ph
AK68-01506L
Downloaded from www.Manualslib.com manuals search engine
PRECAUTIONS
1. Setting up
- Refer to the identification label located on
the rear of your player for its proper operating voltage.
- Install your player in a cabinet with adequate ventilation holes (7~10cm). Do not
block ventilation holes on any of the components for air circulation.
- Do not push the disc tray in by hand.
- Do not stack components.
- Be sure to turn all components off before
moving the player.
- Before connecting other components to this
player, be sure to turn them off.
- Be sure to remove the disc and turn off the
player after use, especially if you are not
going to use it for a long time.
- The mains plug is used as a disconnect
device and shall stay readily operable at
any time.
occurs, leave the player at room temperature until the inside of the player becomes
dry and operational.
4. Disc
- Do not clean the disc using record-cleaning
sprays, benzene, thinner, or other volatile
solvents that may cause damage to the disc
surface.
- Do not touch the disc’s signal surface. Hold
by the edges or by one edge and the hole
in the center.
- Wipe the dirt away gently; never wipe a
cloth back and forth over the disc.
5. Environmental info
- The battery used in this product contains
chemicals that are harmful to the environ
ment.
- So, dispose of batteries in the proper man
ner, according to federal, state, and local
regulations.
2. For your safety
- This product utilizes a laser. Use of controls
or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
- Do not open covers and do not repair yourself. Refer servicing to qualified personnel.
3. Caution
- Your player is not intended for industrial use
but for domestic purposes. Use of this product is for personal use only.
- Apparatus shall not be exposed to dripping
or splashing and no objects filled with liquids, such as vases, shall be placed on the
apparatus.
- Exterior influences such as lightning and
static electricity can affect normal operation
of this player. If this occurs, turn the player
off and on again with the POWER button, or
disconnect and then reconnect the AC
power cord to the AC power outlet. The
player will operate normally.
- When condensation forms inside the player
due to sharp changes in temperature, the
player may not operate correctly. If this
2
Downloaded from www.Manualslib.com manuals search engine
The product unit accompanying this user manual is
licensed under certain intellectual property rights of
certain third parties. This license is limited to private
non-commercial use by end-user consumers for
licensed contents. No rights are granted for
commercial use. The license does not cover any
product unit other than this product unit and the
license does not extend to any unlicensed product
unit or process conforming to ISO/OUR 11172-3 or
ISO/OUR 13818-3 used or sold in combination with
this product unit. The license only covers the use of
this product unit to encode and/or decode audio files
conforming to the ISO/OUR 11172-3 or ISO/OUR
13818-3. No rights are granted under this license for
product features or functions that do not conform to
the ISO/OUR 11172-3 or ISO/OUR 13818-3.
CAUTION: USE OF ANY CONTROLS,
ADJUSTMENTS, OR PROCEDURES OTHER
THAN SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
Accessories
Remote Control
Batteries for Remote
Control (AAA Size)
User’s Manual
Video/Audio
Cable
Install Batteries in the Remote control
1. Open the battery cover on the back of the remote
control.
2. Insert two AAA batteries.
Make sure that the
polarities (+ and -) are aligned correctly.
3. Replace the battery cover.
If remote control doesn’t operate
properly:
- Check the polarity + - of the batteries (Dry-Cell)
- Check if the batteries are drained.
- Check if remote control sensor is blocked by
obstacles.
- Check if there is any fluorescent lighting nearby.
TABLE OF
CONTENTS
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Setup
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Disc Type and Characteristics . . . . . . . . . . . . . . . . 5
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tour of the Remote Control . . . . . . . . . . . . . . . . . . 8
Connections
Choosing a Connection . . . . . . . . . . . . . . . . . . . . . 9
Basic Functions
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using the Search and Skip Functions . . . . . . . . . 15
Using the Display Function . . . . . . . . . . . . . . . . . 15
Using the Disc Menu and Title Menu . . . . . . . . . 16
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Advanced Functions
Adjusting the Aspect Ratio (EZ View) . . . . . . . . . 17
Selecting the Audio Language . . . . . . . . . . . . . . . 18
Selecting the Subtitle Language. . . . . . . . . . . . . . 18
Changing The Camera Angle . . . . . . . . . . . . . . . . 19
Using the Bookmark Function . . . . . . . . . . . . . . . 19
Using the Zoom Function . . . . . . . . . . . . . . . . . . . 20
Clips Menu for MP3/WMA/JPEG/CD Audio . . . . . 20
Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 20
MP3/WMA/CD Audio Playback. . . . . . . . . . . . . . . 21
Playing media files Using
the USB Host Feature . . . . . . . . . . . . . . . . . . . . . 21
CD Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . 23
Karaoke Functions
Karaoke Functions . . . . . . . . . . . . . . . . . . . . . . . . 24
Changing Setup Menu
Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . 25
Setting Up the Language Features . . . . . . . . . . . 25
Setting Up the Audio Options . . . . . . . . . . . . . . . . 26
Setting Up the Display Options . . . . . . . . . . . . . . 27
Setting Up the Parental Control . . . . . . . . . . . . . . 28
Reference
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 30
USB HOST Feature Supported Products . . . . . . . 31
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3
Downloaded from www.Manualslib.com manuals search engine
English
BEFORE YOU
STAR T
SETUP
General Features
Excellent Sound
Dolby Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound reproduction.
Screen
Both regular and widescreen(16:9) pictures can be
viewed.
Slow Motion
An important scene can be viewed in slow motion.
Parental Control (DVD)
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such as those with violence, adult subject
matter, etc.
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
Progressive Scan
Progressive scanning creates an improved picture
with double scan lines of a conventional interlaced
picture.
EZ VIEW (DVD)
Easy View enables picture adjustment to match
your TV's screen size (16:9 or 4:3).
Digital Photo Viewer (JPEG)
You can view digital photos on your TV.
Repeat
You can repeat a song or movie simply by pressing
the REPEAT button.
MP3/WMA
This unit can play discs created from MP3/WMA
files.
CD Ripping
This feature lets you to copy audio files from disc to
USB device into MP3 format. (Only Audio CD (CD
DA)).
4
Downloaded from www.Manualslib.com manuals search engine
Note
- Discs which cannot be played with this player.
• DVD-ROM
• DVD-RAM
• CD-ROM
• CDV
• CDI
• CVD
• CDGs play audio only, not graphics.
- Ability to play back may depend on recording
conditions.
• DVD-R, +R
• CD-RW
• DVD+RW, -RW (V mode)
- The unit may not play certain CD-R, CD-RW
and DVD-R due to the disc type or recording
conditions.
COPY PROTECTION
Many DVD discs are encoded with copy protection.
Because of this, you should only connect your DVD
player directly to your TV, not to a VCR. Connecting
to a VCR results in a distorted picture from copyprotected DVD discs.
This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection technology must be auzthorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
PROGRESSIVE SCAN OUTPUTS
(525p)
“CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE, IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS
REGARDING YOUR TV SET COMPATIBILITY
WITH THIS MODEL 525p AND 625p DVD PLAYER,
PLEASE CONTACT SAMSUNG'S CUSTOMER
SERVICE CENTER.”
Disc Type and Characteristics
This DVD player is capable of playing the following types of discs with the corresponding logos:
Recording Types
DVD
Audio
+
Video
VIDEO-CD
Audio
+
Video
AUDIO-CD
Disc Size
Max. Playing Time
Characteristics
12 Cm
Single-sided 240 min.
Double-sided 480 min.
- DVD contains excellent sound and
video due to Dolby Digital and MPEG2 system.
8 Cm
Single-sided 80 min.
Double-sided 160 min.
- Various screen and audio functions
can be easily selected through the onscreen menu.
12 Cm
74 min.
- Video with CD sound, VHS quality &
MPEG-1 compression technology.
8 Cm
20 min.
12 Cm
74 min.
8 Cm
20 min.
Audio
- CD is recorded as a Digital Signal
with better audio quality, less distortion and less deterioration of audio
quality over time.
Disc Markings
Region Number
~
NTSC
Play Region Number
NTSC broadcast system in U.S.A, Canada,
Korea, Japan, etc
Dolby Digital disc
STEREO
DIGITAL
SOUND
Stereo disc
Both the DVD player and the discs are coded
by region. These regional codes must match in
order for the disc to play. If the codes do not
match, the disc will not play.
The Region Number for this player is
described on the rear panel of the player.
Digital Audio disc
DTS disc
MP3 disc
You must only insert one DVD disc at a time.
Inserting two or more discs will not allow to
play them back and it may cause damage to
the DVD player.
5
Downloaded from www.Manualslib.com manuals search engine
English
Disc Types (Logos)
Description
Front Panel Controls
11
1 2
1.
2.
3.
4.
5.
3
STANDBY/ON ( )
When STANDBY/ON is pressed on, the indicator goes
out and the player is turned on.
STANDBY indicator
When the unit is first plugged in, this indicator lights.
DISC TRAY
Place the disc here.
MIC 1/2
Connect Microphone for karaoke functions.
MICROPHONE VOLUME
Use to adjust microphone volume level. Use the button
by pressing it. Turn it to the left or right to control the
volume.
4
5
6
7
8
9
10
8
6.
USB Host
Connect digital still camera, MP3 player, memory stick,
Card reader, or another removable storage devices
7. OPEN/CLOSE ( )
Press to open and close the disc tray.
8. SKIP ( / ) SEARCH
Allow you to search forward/backward through
a disc. Use to skip the title, chapter or track.
9. STOP ( )
Stops disc play.
10. PLAY/PAUSE ( )
Begin or pause disc play.
11. DISPLAY
Operation indicators are displayed here.
Front Panel Display
Total playing time/Displays various messages concerning operations such as PLAY,
STOP, LOAD ...
nodSC: No disc loaded.
OPEn: The disc tray is open.
LOAd: Player is loading disc information.
6
Downloaded from www.Manualslib.com manuals search engine
Rear Panel
English
1
3
1.DIGITAL AUDIO OUT JACKS
- Use either a coaxial digital cable to connect to
a compatible Dolby Digital receiver.
- Use to connect to an A/V Amplifier that contains a
Dolby Digital, MPEG2 or DTS decoder.
2. COMPONENT VIDEO OUT JACKS
- Use these jacks if you have a TV with Component
Video in jacks. These jacks provide PR, PB and Y
video.
- If Component(P-SCAN) Video Output is selected in
Setup Menu, progressive scan mode will work.
- If Component(I-SCAN) Video Output is selected in
Setup Menu, interlaced scan mode will work.
4
2
3. AUDIO OUT JACKS
Connect to the Audio input jacks of your television or
audio/video receiver.
4. VIDEO OUT JACK
- Use a video cable to connect to the Video input jack on
your television.
Note
- Consult your TV User’s Manual to find out if your TV supports Progressive Scan.
If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in
the TV’s menu system.
- See pages 27 to get more information on how to use the setup menu.
7
Downloaded from www.Manualslib.com manuals search engine
Tour of the Remote Control
5.
TV VOL (+, -) Buttons
Control volume.
6.
15
16
1
7.
8.
9.
2
17
10.
3
4
5
6
7
8
9
18
19
20
21
11.
22
23
13.
12.
14.
15.
10
16.
11
12
24
25
13
14
26
27
17.
18
19.
VIDEO SEL. Button
Selects video output formats
SKIP Buttons (
)
/
Use to skip the title, chapter or track
STOP Button (
)
MENU Button
Brings up the DVD player’s menu.
œ/ƒ,¦/‹ Buttons
ENTER/œ
This button functions as a toggle switch.
EZ VIEW Button
The aspect ratio of a picture can easily be adjusted
according to the screen size of your TV (16:9 or 4:3).
DISC MENU Button
Brings up the Disc menu.
OPEN/CLOSE (
) Button
To open and close the disc tray.
AUDIO Button
Use this button to access various audio functions on a disc.
DVD Button
Press this button when you use a DVD player.
TV Button
Press this button to operate TV.
REPEAT A-B Button
Allows you to repeat A-B disc.
STEP Button/TV Source
Advances play one frame at a time/Press this button to
select the an available TV source (TV mode).
KARAOKE Button
Use to begin Karaoke functions.
20. TV CH (
,
Channel selection.
1.
2.
3.
4.
DVD POWER Button
Turns the power on or off.
NUMBER Buttons
ZOOM Button / (-/--)
Enlarge DVD Picture / Use this button to select the
channel of TV program by inserted the channel number
(TV mode)
SEARCH Buttons (
)
/
Allow you to search forward/backward through a disc.
8
Downloaded from www.Manualslib.com manuals search engine
) Buttons
21. SUBTITLE Button
22. PLAY/PAUSE Button (
)
Begin/Pause disc play.
23. RETURN Button
Returns to a previous menu.
24. INFO Button
Displays the current disc mode.
25. CANCEL Button
Use to remove menus or status displays from the
screen.
26. USB Button
27. REPEAT Button
Allows you to repeat play a title, chapter, track, or disc.
CONNECTIONS
The following shows examples of connections commonly used to connect the DVD player with a TV and
other components.
Before Connecting the DVD Player
- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
- Refer to the user’s manual of the additional components you are connecting for more information on those
particular components.
Connection to a TV (For Video)
1
Using video/audio cables, connect the VIDEO
(yellow)/AUDIO (red and white) OUT terminals on the rear
of the DVD player to the VIDEO (yellow)/AUDIO (red and
white) IN terminals of TV.
2
WHITE
RED
Turn on the DVD player and TV.
YELLOW
Audio
Cable
Video
Cable
3
RED
WHITE
YELLOW
Press the TV/VIDEO button on the TV's remote control to
select Video.
Note
- Noise may be generated if the audio cable is too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 12 to 13)
- The number and position of terminals can vary depending on your TV set. Please refer to the user's manual of the TV.
- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the
DVD player.
9
Downloaded from www.Manualslib.com manuals search engine
English
Choosing a Connection
Connection to a TV (Interlace)
- Connecting to your TV using Component video cables.
- You will enjoy high quality and accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images. (Audio
signals are delivered through the audio output.)
1
Using component video cables (not included), connect the
COMPONENT VIDEO OUT terminal on the rear of the
DVD player to the COMPONENT IN terminal of TV.
2
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of TV. Turn on the
DVD player and TV.
BLUE
GREEN
WHITE
RED
3
RED
Audio Cable
Press the TV/VIDEO button on the TV's remote control to
select Component or DVD.
Component cable
(not included)
BLUE
RED
WHITE
RED
GREEN
4
Set the Video Output to (I-SCAN) in the Display Setup
menu. (See pages 27 to 28)
Note
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 12 to 13)
- The component terminal of TV can be marked by “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “PR, PB, Y”
depending on the manufacturer. The number and position of terminals can vary depending on the TV set.
Please refer to the user's manual of the TV.
10
Downloaded from www.Manualslib.com manuals search engine
Connection to a TV (Progressive)
1
2
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of TV. Turn on the
DVD player and TV.
BLUE
English
Using component video cables (not included), connect the
COMPONENT VIDEO OUT terminal on the rear of the
DVD player to the COMPONENT IN terminal of TV.
GREEN
WHITE
RED
RED
3
Press the TV/VIDEO button on the TV's remote control to
select Component or DVD.
Component cable
(not included)
Audio Cable
RED
WHITE
RED
BLUE
GREEN
4
Set the Video Output to (P-SCAN) in the Display Setup
menu. (See pages 27 to 28)
To see the progressive video output,
-You
Consult
TVsupporting
User’s Manual
to find out
need ayour
TV set
the progressive
scanif your TV supports Progressive Scan. If Progressive
Scan isfunction.
supported,
follow
TV up
User’s
Manual regarding Progressive Scan settings in the TV’s
input
And you
havethe
to set
the TV
menu system.
- Depending on your TV, the connection method may differ from the illustration above.
Note
- What is "Progressive Scan"?
Progressive scan has twice as many scanning lines as the interlace output method has. Progressive
scanning method can provide better and clearer picture quality.
11
Downloaded from www.Manualslib.com manuals search engine
Connection to an Audio System (2 Channel Amplifier)
1
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO or
COMPONENT OUT terminals on the rear of the DVD player to the VIDEO or COMPONENT IN terminal of your TV.
WHITE
RED
3
Turn on the DVD player, TV, and Amplifier.
Audio Cable
RED
WHITE
4
Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 26 to 27)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
12
Downloaded from www.Manualslib.com manuals search engine
Connection to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)
1
English
If using a coaxial cable (not included), connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the
DVD player to the DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO or
COMPONENT OUT terminals on the rear of the DVD player to the VIDEO or COMPONENT IN terminal of TV.
3
Turn on the DVD player, TV, and Amplifier.
Coaxial Cable
(not included)
4
Press the input select button of the Amplifier to select
external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 26 to 27)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
13
Downloaded from www.Manualslib.com manuals search engine
BASIC FUNCTIONS
4. Stopping Play
Press the STOP (
Playing a Disc
Before Play
- Turn on your TV and set it to the correct Video
Input by pressing TV/VIDEO button on the TV
remote control.
- If you connected an external Audio System, turn
on your Audio System and set it to the correct
Audio Input.
After plugging in the player, the first time you press the DVD
POWER button, this screen comes up: If you want to select
a language, press a NUMBER button. (This screen will only
appear when you plug in the player for the first time.)
If the language for the startup screen is not set, the settings
may change whenever you turn the power on or off.
Therefore, make sure that you select the language you want
to use.
Once you select a menu language, you can change it by
pressing the
button on the front panel of the unit for more
than 5 seconds with no disc in the unit. Then the SELECT
MENU LANGUAGE window appears again where you can
reset your preferred language.
Press
Touche
Drücken Sie
Pulsar
1 for English
2 pour Français
3 für Deutsch
4 para Español
Premere
5 per Italiano
Druk op
6 voor Nederlands
Playback
1. Press the OPEN/CLOSE ( ) button. The STANDBY
indicator light goes out and the tray opens.
2. Place a disc gently into the tray with the disc’s label facing
up.
- You must only insert one DVD disc at a time.
Inserting two or more discs will not allow to play them
back and it may cause damage to the DVD player.
3. Press the PLAY/PAUSE ( ) button or OPEN/ CLOSE
( ) button to close the disc tray.
- When you stop disc play, the player remembers
where you stopped, so when you press
PLAY/PAUSE ( ) button again, it will pick up where
you left off.
14
Downloaded from www.Manualslib.com manuals search engine
) button during play.
5. Removing Disc
Press the OPEN/CLOSE (
) button.
6. Pausing Play
Press the PLAY/PAUSE ( ) or STEP button on the
remote control during play.
- Screen stops, no sound.
To resume, press the PLAY/PAUSE ( )
button once again.
7. Step Motion Play (Except CD)
Press the STEP button on the remote control during play.
- Each time the button is pressed, a new frame will
appear.
- No sound is heard during STEP mode.
- Press the PLAY/PAUSE ( ) button to resume
normal play.
- You can only perform step motion play in the
forward direction.
8. Slow Motion Play
Press the SEARCH (
/ ) button to choose
the play speed between 1/8, 1/4 and 1/2 of normal during
PAUSE or STEP mode.
- No sound is heard during slow mode.
- Press the PLAY/PAUSE ( ) button to resume
normal play.
Note
- If the player is left in the stop mode for more
than one minute without any user interaction, a
screen saver will be activated. Press the
PLAY/PAUSE ( ) button to resume normal play.
- If the player is left in the stop mode for more than
about 30 minutes, the power will automatically
shut off except when the MIC is connected.
(Automatic Power-Off Function)
- If the player is left for about 5 minutes in pause
mode, it will stop.
- This (
) icon indicates an invalid button press.
During play, you can search quickly through a chapter or
track, and use the skip function to jump to the next selection.
Searching through a Chapter or
Track
During play, press the SEARCH (
or
remote control for more than 1 second.
DVD
2X, 4X, 64X, 128X
VCD
4x, 8X
CD
2X, 4X, 8X
When Playing a DVD/VCD
1. During play, press the INFO button on the remote control.
2. Press the œ/ƒbuttons to select the desired item.
- Only Menu Off is available for VCD2.0. Each press of
the DISC MENU button toggles between Menu On and
Menu Off.
3. Press the ¦/‹ buttons to make the desired setup and then
press the ENTER button.
- You may use the number buttons of the remote control
to directly access a title, chapter or to start the
playback from the desired time.
) button on the
4. To make the screen disappear, press the CANCEL button
again.
Note
Note
- The speed marked in this function may be
different from the actual speed of playback.
- No sound is hearing during search mode
(Except CD).
Title
Skipping Tracks
During play, press the SKIP (
Using the Display Function
Chapter
or
) button, it
moves to the next chapter. If you press the SKIP (
)
button, it moves to the beginning of the chapter. One more
Time
press makes it move to the beginning of the previous
chapter.
- When playing a VCD 2.0 in Menu Off mode, or a VCD 1.1
Audio
Subtitle
Refers to the subtitle languages available in
the disc. You will be able to choose the
subtitle languages or, if you prefer, turn them
off from the screen. A DVD disc can have up
to 32 different subtitles.
) button, it moves
to the beginning of the track. One more press makes it
move to the beginning of the previous track.
- If a track exceeds 15 minutes when playing a VCD and
If you press the
Allows playback of the film from a desired
time. You must enter the starting time as a
reference.The time search function does not
operate on some disc.
Refers to the language of the film soundtrack.
In the example, the soundtrack is played in
English 5.1CH. A DVD disc can have up to
eight different soundtracks.
) button, it moves to
the next track. If you press the SKIP (
you press the
Most DVD discs are recorded in chapters so
that you can quickly find a specific passage
(similar to tracks on an video CD).
) button.
- When playing a DVD, if you press the SKIP (
or a CD, if you press the SKIP (
To access the desired title when there are
more than one in the disc. For example, if
there is more than one movie on a DVD,
each movie will be identified.
button, it moves forward 5 minutes.
button, it moves backward 5 minutes.
Note
Only Menu Off is available for VCD2.0. Each press
of the DISC MENU button toggles between Menu
On and Menu Off.
Shortcut
To access the desired Bookmark, Angle or
EZ View function.
Some DVD discs are have more angle function from any picture.
Bookmark function make you easily and
quickly to find a track or chapter from DVD
or VCD ( Menu Off).
The EZ View function is use for changing the
aspect ratio in DVD.
15
Downloaded from www.Manualslib.com manuals search engine
English
Using the Search and Skip
Functions
Using the Disc Menu and
Title Menu
Using the Disc Menu
1. During Stop mode, press the MENU button on the remote
control.
2. Press the œ/ƒ buttons to select Disc Menu, then press the
‹ or ENTER button.
Press ENTER key
for Disc Menu
Repeat Play
Repeat the current track, chapter, title, a chosen
section (A-B), or all of the disc.
When playing a DVD/VCD
1. Press the REPEAT button on the remote control.
Repeat screen appears.
2. Press the ¦/‹ buttons to select Chapter, Title or A-B,
then press the ENTER button.
- DVD repeats play by chapter or title, VCD
repeat play by disc or track.
- Chapter ( ): repeats the chapter that is playing.
- Title ( ): repeats the title that is playing.
- Disc ( ): repeats the disc that is playing.
- Track ( ): repeats the track that is playing.
- A-B: repeats a segment of the disc that you select.
T
Enter
Return
Menu
Note
- Depending on a disc, the Disc Menu may not
work.
- You can also use the Disc Menu, using the
DISC MENU button on the remote control.
- Only Menu Off is available for VCD2.0. Each
press of the DISC MENU button toggles
between Menu On and Menu Off.
Using the Title Menu
1. During Stop mode, press the MENU button on the remote
control.
2. Press the œ/ƒ buttons to select Title Menu, then press
the ‹ or ENTER button.
DVD
Off
01
01 A - B
T
ENTER REPEAT
VCD
Off
01
T
D
01 A - B
ENTER REPEAT
Using the A-B Repeat function
1. Press the REPEAT button on the remote control.
2. Press the ¦/‹ buttons to Select A-B button.
3. Press the ENTER button at the point where you want
repeat play to start (A). B is automatically highligh ted.
4. Press the ENTER button at the point where you want the
repeat play to stop (B).
- To return to normal play, press the CANCEL button.
5. To return to normal play, press REPEAT button again, then
press the ¦/‹ buttons to select Off and press ENTER
button.
Press ENTER key
for Title Menu
DVD
Off
Enter
Return
Note
- Depending on a disc, the Title Menu may not
work.
- Title Menu will only be displayed if there are at
least two titles in the disc.
16
Downloaded from www.Manualslib.com manuals search engine
01
01 A - B
T
ENTER REPEAT
Menu
VCD
Off
T
01
D
01 A - B
ENTER REPEAT
Adjusting the Aspect Ratio
(EZ View)
To play back using aspect ratio
(DVD)
Slow Play
This feature allows you to play scenes slowly containing sports, dancing, musical instruments being
played etc., so you can study them more closely.
When playing a DVD
1. During play, press the PLAY/PAUSE (
ADVANCED
FUNCTIONS
) button.
2. Press the SEARCH (
) button to choose
/
the play speed between 1/8, 1/4 and 1/2 of normal during
PAUSE or STEP mode.
Press the EZ VIEW button.
- The screen size changes when the button is pressed
repeatedly.
- The screen zoom mode operates differently depending on the
screen setting in the Display Setup menu.
- To ensure correct operation of the EZ VIEW button, you
should set the correct aspect ratio in the Display Setup
menu. (See pages 27 to 28).
WIDE SCREEN
EZ VIEW
If you are using a 16:9 TV
For 16:9 aspect ratio discs
- WIDE SCREEN
Displays the content of the DVD title in 16:9 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the black bars at
the top and bottom of the screen will disappear. The picture
will look vertically stretched. (Depending on a type of disc,
the black bars may not disappear completely.)
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarge
For 4:3 aspect ratio discs
- Normal Wide
Displays the content of the DVD title in 16:9 aspect ratio.
The picture will look horizontally stretched.
- SCREEN FIT
The top and bottom portions of the screen are cut off and
the full screen appears.
The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are
cut off and the central portion of the screen is enlarged.
- Vertical Fit
When a 4:3 DVD is viewed on a 16:9 TV, black bars will
appear at the left and right of the screen in order to prevent
the picture from looking horizontally stretched.
17
Downloaded from www.Manualslib.com manuals search engine
English
Note
- A-B REPEAT allows you to set point (B) until at
least 5 seconds of play back time has elapsed
after point (A) has been set.
- Depending on a disc, the Repeat function may
not work.
- Only Menu Off is available for VCD2.0. Each
press of the DISC MENU button toggles
between Menu On and Menu Off.
If you are using a 4:3 TV
For 16:9 aspect ratio discs
- 4:3 Letter Box
Displays the content of the DVD title in 16:9 aspect ratio. The
black bars will appear at the top and bottom of the screen.
- 4:3 Pan& Scan
The left and right portions of the screen are cut off and the
central portion of the 16:9 screen is displayed.
- SCREEN FIT
The top and bottom portions of the screen are cut off and a
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarged.
For 4:3 aspect ratio discs
- Normal Screen
Displays the content of the DVD title in 4:3 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off and the
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are cut
off and the central portion of the screen is enlarged.
Note
This function may behave differently depending on
the type of disc.
Selecting the Audio
Language
You can select a desired audio language quickly and
easily with the AUDIO button.
Using the AUDIO button
1. Press the AUDIO button. The Audio changes when the
button is pressed repeatedly.
The audio languages are represented by
abbreviations.
DVD
ENG DOLBY DIGITAL 5.1CH
AUDIO
VCD
When playing a VCD,
you can select among
Stereo, Left or Right
Stereo
AUDIO
2. To remove the AUDIO icon, press the CANCEL or RETURN
button.
18
Downloaded from www.Manualslib.com manuals search engine
Note
- This function depends on audio languages are
encoded on the disc and may not work.
- A DVD disc can contain up to 8 audio languages.
- To have the same audio language come up
whenever you play a DVD;
Refer to “Using the Audio Language” on page
26.
Selecting the Subtitle
Language
You can select a desired subtitle quickly and easily
with the SUBTITLE button.
Using the SUBTITLE button (DVD)
1. Press the SUBTITLE button. The subtitle languages are
represented by abbreviations. The subtitle changes when
the button is pressed repeatedly.
DVD
Off
SUBTITLE
2. To remove the SUBTITLE icon, press the CANCEL or
RETURN button.
Note
- You have to change the desired subtitle in the
Disc Menu, according to discs. Press the DISC
MENU button.
- This function depends on what subtitles are
encoded on the disc and may not work on all
DVDs.
- A DVD disc can contain up to 32 subtitle
languages.
- To have the same subtitle language come up
whenever you play a DVD; Refer to “Using the
Subtitle Language” on page 26.
VCD
Changing the Camera
Angle
Shortcut
Enter
4. When you reach the scene you want to mark, press the
ENTER button. Up to three scenes may be marked at a
time.
English
When a DVD contains multiple angles of a particular
scene, you can use the ANGLE function.
Using the ANGLE Function (DVD)
If the disc contains multiple angles, the ANGLE
appears on the screen.
Bookmark
1 - -
1. During play mode, press the INFO button on the remote
control.
2. Press the œ/ƒ buttons to select Shortcut.
3. Press the ¦/‹ buttons to select Angle, then press the
ENTER button.
Shortcut
Angle
Enter
4. Press the ¦/‹ buttons or you can use the number buttons
on the remote control to select the desired angle.
4/6
Note
- If the disc has only one angle, this feature won’t
work. Currently, very few discs have this feature.
- Depending on the disc, these functions may not
work
Note
- Only Menu Off is available for VCD2.0. Each
press of the DISC MENU button toggles
between Menu On and Menu Off.
- Depending on a disc, the Bookmark function
may not work.
Recalling a Marked Scene
1~3. The first 1~3 steps are the same as those for “Using the
Bookmark Function” on page 19.
4. Press the ¦/‹ buttons to select a marked scene.
1 2 3
5. Press the PLAY/PAUSE (
scene.
) button to skip to the marked
Clearing a Bookmark
Using the Bookmark
Function
1~3. The first 1~3 steps are the same as those for “Using the
Bookmark Function” on page 19.
This feature lets you bookmark sections of a DVD or
VCD (Menu Off mode) so you can quickly find them
at a later time.
Using the Bookmark Function
(DVD/VCD)
4. Press the ¦/‹ buttons to select the bookmark number you
want to delete.
5. Press the CANCEL button to delete a bookmark number.
1 2 3
1. During play, press the INFO button on the remote control.
2. Press the œ/ƒ buttons to select Shortcut.
3. Press the ¦/‹ buttons to select Bookmark (Except VCD),
then press the ENTER button.
DVD
Shortcut
Bookmark
Enter
19
Downloaded from www.Manualslib.com manuals search engine
Using the Zoom Function
Using the Zoom Function
(DVD/VCD)
1. During Play or Pause mode, press the ZOOM button on the
remote control, and than press the ENTER button.
2. Press the œ/ƒ or ¦/‹buttons to select the part of the
screen you want to zoom in on.
-
: Name of currently playing file.
-
: Current Playback Time.
-
: Current Playback Mode : There are four
modes. They can be selected in order by
pressing the REPEAT button.
- Off: Normal Playback
- Track: Repeats the current track.
- During DVD play, press ENTER to zoom in
2X/4X/2X/Normal in order.
- During VCD play, press ENTER to zoom in
2X/4X/2X/Normal in order.
- Folder: Repeats the current folder
- Random: Files in the disc will be played in
random order.
: MP3 file icon.
-
: Folder icon.
-
: WMA file icon.
-
: Current Folder icon.
-
: JPEG file icon.
-
: CD Audio file icon.
-
Folder Selection
The folder can be selected both in Stop or Play mode.
Clips Menu for
MP3/WMA/JPEG/CD Audio
CD Audio or discs with MP3/WMA/JPEG contain
individual songs and/or pictures that can be organized into folders as shown below. They are similar
to how you use your computer to put files into different folders.
Off
Stop
Open the disc tray.
Place the disc on the
tray.
Close the tray.
The tray closes and this
screen displays.
00:00:00
WMA
- To select the Parent Folder
Press the RETURN button to go to parent folder, or press the
œ/ƒ
ƒ buttons to select “..” and press ENTER to go to the
parent folder.
- To select the Peer Folder
œ/ƒ
ƒ buttons to select the desired folder, then
Press theœ
press ENTER.
- To select the Sub-Folder
ƒ buttons to select the desired folder,
Press the œ/ƒ
then press ENTER.
Root
WMA
JPEG
JPEG
MP3
Parent Folder
MP3
MUSIC
Enter
Return
Menu
Current Folder
1st
Sub-Folders
2nd
SONG FILE 1
Peer Folders
SONG FILE 2
SONG FILE 3
20
Downloaded from www.Manualslib.com manuals search engine
1. Open the disc tray. Place the disc on the tray. Close the tray.
- Only one kind of file is played back when a disc or a
folder contains both MP3 and WMA files.
ƒ buttons to select a song file.
2. Press the œ/ƒ
Press ENTER to begin playback of the song file.
Off
Play
00:00:23
B e c a u s e Yo u
...
B e c a u s e Yo u
Cactus
Sad Dayu
Wonderful
Enter
Return
REPEAT
Repeat
Repeat/Random Playback
Press the REPEAT button to change the playback mode. There
are four modes, such as Off, Track, Folder and Random.
- Off: Normal Playback
- Track: Repeats the current song file.
- Folder: Repeats the song files which have the same
extension in the current folder.
- Random: Song files which have the same extension will be
played in random order.
To resume normal play, press the CANCEL button.
CD-R MP3/WMA file
When you record MP3 or WMA files on CD-R, please refer
to the following.
- Your MP3 or WMA files should be ISO 9660 or JOLIET
format.
ISO 9660 format and Joliet MP3 or WMA files are
compatible with Microsoft's DOS and Windows, and with
Apple's Mac. This format is the most widely used.
- When naming your MP3 or WMA files, do not exceed 8
characters, and enter “.mp3, .wma” as the file extension.
General name format : Title.mp3. or Title.wma. When
composing your title, make sure that you use 8 characters or
less, have no spaces in the name, and avoid the use of
special characters including: (.,/,\,=,+).
- Use a decompression transfer rate of at least 128 Kbps
when recording MP3 files.
Sound quality with MP3 files basically depends on the rate of
compression/decompression you choose. Getting CD audio
sound requires an analog/digital sampling rate, that is
conversion to MP3 format, of at least 128 Kbps and up to 160
Kbps. However, choosing higher rates, like 192 Kbps or more,
only rarely give better sound quality. Conversely, files with
decompression rates below 128 Kbps will not be played
properly.
- Use a decompression transfer rate of at least 64Kbps
when recording WMA files.
Sound quality with WMA files basically depends on the rate of
compression/decompression you choose.
Getting CD audio sound requires an analog/digital sampling
rate, that is conversion to WMA format, of at least 64Kbps
and up to 192Kbps. Conversely, files with decompression
rates below 64Kbps or over 192Kbps will not be played
properly.
- Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected to
prevent illegal copying. These files are of the following types:
TM
Windows Media (registered trade mark of Microsoft Inc) and
TM
SDMI (registered trade mark of The SDMI Foundation). You
cannot copy such files.
- Important:
The above recommendations cannot be taken as a guaran
tee that the DVD player will play MP3 recordings, or as an
assurance of sound quality. You should note that certain
technologies and methods for MP3 file recording on CD-Rs
prevent optimal playback of these files on your DVD player
(degraded sound quality and in some cases, inability of the
player to read the files).
- This unit can play a maximum of 500 files and 500 folders
per disc.
Playing Media Files Using
the USB Host feature
You can enjoy the media files such as pictures, movies and
tunes saved in an MP3 player, USB memory or digital camera in high audio by connecting the storage device to the
USB port of the DVD Player.
Using the USB HOST feature
1. Connect the USB device to the USB port on the front of the
unit.
ƒ button to select
2. If there is partision Of USB, Press the œ/ƒ
the one of partision from USB, then Press OK.
Disc
USB
21
Downloaded from www.Manualslib.com manuals search engine
English
MP3/WMA/CD Audio Playback
ƒ or ¦/‹
‹ buttons to select a file in
3. Press the œ/ƒ
USB. Press OK to Open file.
STOP
Off
00:00:00
5. USB card Reader: One slot USB card reader and Multi slot
USB card reader
• Depending on the manufacturer. the USB card reader
may not be supported.
• If you install multiple memory devices into a multi card
reader, you may experience problems.
6. If you use a USB extension cable, the USB device might not
be recognized.
• Supported Formats
Note
• Each time the USB button on the remote control is
pressed, a frame of the USB device selection will
appear.
• “USB” appears on the display screen.
• USB MENU screen appears on the TV screen and the
saved file is played.
Safe USB Removal
To prevent damage to the memory stored in the USB device,
perform safe removal before disconnecting the USB cable.
- Press the STOP (
) button
- Remove the USB cable.
Skip Forward/Back
During playback, press the (
/
) button.
• When there is more than one file, when you press the
button, the next file is selected.
• When there is more than one file, when you press the
button, the previous file is selected.
Fast playback
To play back the disc at a faster speed, press
(
/
) during playback.
• Each time you press either button, the playback speed will
change as follows:
2x ➞ 4x ➞ 8x.
Compatible Devices
1. USB devices that support USB Mass Storage v1.0.
(USB devices that operate as a removable disk in Windows
(2000 or later) without additional driver installation.)
2. MP3 Player: HDD and flash type MP3 player.
3. Digital camera: Cameras that support USB Mass Storage
v1.0.
• Cameras that operate as a removable disk in Windows
(2000 or later) without additional driver installation.
4. USB HDD and USB Flash Drive: Devices that support
USB2.0 or USB1.1.
• You may experience a difference in playback quality when
you connect a USB1.1 device.
• For a USB HDD, make sure to connect an auxiliary power
cord to the USB HDD for proper operation.
22
Downloaded from www.Manualslib.com manuals search engine
• CBI (Control/Bulk/Interrupt) is not supported.
• Digital Cameras that use PTP protocol or require additional
program installation when connected to a PC are not supported.
• A device using NTFS file system is not supported.
(Only FAT 16/32 (File Allocation Table 16/32) file system is
supported.)
• Some MP3 players, when connected to this product,may not
operate depending on the sector size of their file system.
• The USB HOST function is not supported if a product that
transfers media files by its manufacturer-specific program is
connected.
• Does not operate with Janus enabled MTP(Media Transfer
Protocol) devices.
• The USB host function of this product does not support
all USB devices.
For information on the supported devices, see page 31.
CD Ripping
Picture CD Playback
This feature lets you to copy audio files from disc to USB
device into MP3 format.
Off
Play
Open the dics tray.
Track 01
T
00:00:00
Track 01
Place the Audio CD(CD DA) disc on
the tray, and close the tray.
Track 02
DEV : SELECT
START
Track 03
Track 04
Track 05
1. Select the desired folder.
ƒ buttons to select a Picture file in the clips
2. Press the œ/ƒ
menu and then press the ENTER button.
3. Press the INFO button on the remote control to select the
menu you want to view and then press the ENTER button.
Track 06
Track 07
Track 08
English
Connect the USB device to the USB
port on the front of the unit.
ENTER RETURN
Enter
REPEAT
Repeat
This screen will displayed.
1. To Select DISC
ƒ buttons to
With the unit in Stop mode, Press the œ/ƒ
select DISC.
To Select DEV (storage media device)
Press the ‹ button to select the DEV (storage media
device) menu, then press the ENTER button.
ƒ buttons to select USB, then press the
Press the œ/ƒ
ENTER button.
Stop
Off
Disc Track 01
T
00:00:00
Note
- Press the STOP button to return to the clips
menu.
- When playing a Kodak Picture CD, the unit
displays the Photo directly, not the clips menu.
Rotation
USB
Track 01
Track 02
: Each time the ENTER button is pressed, the
picture rotates 90 degrees clockwise.
DEV : SELECT
START
Track 03
Track 04
Track 05
Track 06
Track 07
Track 08
Enter
Zoom
Menu
ƒ buttons to select SELECT, then press the
2. Press the œ/ƒ
ENTER button to marked all files to be copying.
- To unmarked copying all files press the ENTER button
again.(UNSELECT Menu)
- If you want to marked several files to be copying, press the
¦ button, then press the ENTER button on the selected
file.
ƒ buttons to select START, then press the
3. Press the œ/ƒ
ENTER button.
File copy begins.
- To cancel the copying in progress, press the CANCEL but
ton.
Play
Off
Track 01
ƒ buttons to select the part of the
: Press the œ/ƒ
screen you want to zoom in on.
Press the ENTER button. Each time the ENTER button is pressed, the picture is enlarged up to 2X.
Slide Show
•
• Before beginning the Slide Show, the picture interval must
be set.
•
: When this icon is selected and ENTER is
pressed, the pictures change automatically
with about a 6 second interval.
DEV : USB 1
UNSELECT
START
•
: The pictures change automatically with
about a 12 second interval.
Repeat
•
: The pictures change automatically with
about a 18 second interval.
T
00:03:15
Track 01
Track 02
Track 03
Track 04
Track
05
CD
Ripping
START
Track 06
Track 07
CANCEL
: The unit enters slide show mode.
Cancel Ripping
Enter
REPEAT
Note
- When the CD ripping being processed the player
will automatic in play mode.
- Only the Audio CD(CD DA) dics can be ripping.
- During the CD Ripping process, do not
use/press other button besides the CANCEL bu
ton.
23
Downloaded from www.Manualslib.com manuals search engine
TIMER:
ENTER RETURN
KARAOKE FUNCTIONS
Note
- Depending on a file size, the amount of time
between each picture may be different from the
manual.
- If you don’t press any button, the slide show will
start automatically in about 10 seconds by
default.
Karaoke Functions
Operation Sequence
1. Connect the Mixed Audio Out terminals with the TV or
Amplifier. (see page 9 to 13)
2. Connect Mic into Mic jack. When a MIC is connected, the
karaoke functions can be used.
CD-R JPEG Discs
- Only files with the “.jpg” and “.JPG” extensions can be played.
- If the disc is not closed, it will take longer to start playing and
not all of the recorded files may be played.
- Only CD-R discs with JPEG files in ISO 9660 or Joliet format
can be played.
- The name of the JPEG file may not be longer than 8
characters and should contain no blank spaces or special
characters (. / = +).
- Only a consecutively written multi-session disc can be played.
If there is a blank segment in the multi-session disc, the disc
can be played only up to the blank segment.
- A maximum of 3000 images can be stored on a single CD.
- Kodak Picture CDs are recommended.
- When playing a Kodak Picture CD, only the JPEG files in the
pictures folder can be played.
- Kodak Picture CD: The JPEG files in the pictures folder can
be played automatically.
- Konica Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- Fuji Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- QSS Picture CD: The unit may not play QSS Picture CD.
- If the number of files in 1 Disc is over 500, only 500 JPEG
files can be played.
- If the number of folders in 1 Disc is over 500, only JPEG
files in 500 folders can be played
24
Downloaded from www.Manualslib.com manuals search engine
Key Control
1. Playback the Karaoke Disc containing the wanted songs.
Press the KARAOKE button.
‹ buttons to change the desired tone.
2. Press the ¦/‹
Note
- If you hear feedback(squealing or howling) while
using the karaoke feature, move the microphone
away from the speakers or turn down the
microphone volume or the speaker volume.
- When playing MP3, WMA, DTS and LPCM disc,
the karaoke functions will not operate.
- When the MIC is connected, Digital Out does not
work.
- If the MIC is connected in VCD 2.0, Playback is
selected to Menu off mode automatically.
- The MIC sound outputs only from Analog Audio
Out.
- When microphone is inserted, then there will be
no digital audio output through coaxial.
CHANGING SETUP
MENU
Setting Up the Language
Features
If you set the player menu, disc menu, audio and subtitle
language in advance, they will come up automatically every
time you watch a movie.
Using the Setup Menu
The Setup menu lets you customize your DVD player by
allowing you to select various language preferences, set up
a parental level, even adjust the player to the type of
television screen you have.
1. With the unit in Stop mode, press the MENU button on the
ƒ buttons to select Setup, then
remote control. Use the œ/ƒ
press the ‹ or ENTER button.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Language Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
ƒ buttons to select Player Menu, then press
4. Press the œ/ƒ
the ‹ or ENTER button.
ƒ buttons to select the desired language,
5. Press the œ/ƒ
then press the ‹ or ENTER button.
- The language is selected and the screen
returns to Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
LANGUAGE SETUP
Enter
Return
Menu
Player Menu
Disc Menu
❶ Language Setup: Setup of the Language.
❷ Audio Setup : Setup of the Audio Options.
❸ Display Setup : Setup of the Display Options. Use to
select which type of screen you want to
watch and several display options.
❹ Parental Setup : Setup of the Parental Level. Allows
users to set the level necessary to
prevent children from viewing unsuitable
movies such as those with violence,
adult subject matter, etc.
ƒ buttons to access the different features.
2. Press the œ/ƒ
Press the ‹ or ENTER button to access the sub features.
3. To make the setup screen disappear after setting up, press
the MENU button again.
Note
Depending on the disc, some Setup Menu selections may not work.
Audio
: English
√ English
: English
Deutsch
: English
Subtitle
: English
Italiano
Nederlands
Return
Enter
Menu
Using the Disc Menu Language
This function changes the text language only on the disc
menu screens.
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Language Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
ƒ buttons to select Disc Menu, then press
4. Press the œ/ƒ
the ‹ or ENTER button.
ƒ buttons to select the desired
language,
5. Press the œ/ƒ
then press the ‹ or ENTER button.
- If the selected language is not recorded on the disc,
the original pre-recorded language is selected.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
LANGUAGE SETUP
Player Menu
Disc Menu
Audio
: English
√ English
: English
Deutsch
: English
Subtitle
Enter
: English
Italiano
Nederlands
Return
Menu
25
Downloaded from www.Manualslib.com manuals search engine
English
Using the Player Menu Language
Using the Audio Language
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Language Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
ƒ buttons to select Audio, then press the ‹
4. Press the œ/ƒ
or ENTER button.
ƒ buttons to select the desired language, then
5. Press the œ/ƒ
press the ‹ or ENTER button.
- Select “Original” if you want the default soundtrack
language to be the original language the disc is
recorded in.
- If the selected language is not recorded on the disc, the
original pre-recorded language is selected.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
Setting Up the Audio
Options
Audio Options allows you to setup the audio device
and sound status settings depending on the audio
system in use.
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Audio Setup, then press
3. Press the œ/ƒ
the ‹ or ENTER button.
ƒ buttons to select the desired item, then
4. Press the œ/ƒ
press the ‹ or ENTER button.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
LANGUAGE SETUP
Enter
Player Menu
Disc Menu
Audio
Subtitle
: English
Original
: English
√ English
: English
Deutsch
: English
Italiano
Return
Menu
AUDIO SETUP
Dolby Digital Out
:PCM
MPEG-2 Digital Out
:PCM
Dynamic Compression :On
Enter
Return
Menu
PCM Down Sampling
:On
Using the Subtitle Language
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Language Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
ƒ buttons to select Subtitle, then press the ‹
4. Press the œ/ƒ
or ENTER button.
ƒ buttons to select the desired language,
5. Press the œ/ƒ
then press the ‹ or ENTER button.
- Select “Automatic” if you want the subtitle language to
be the same as the language selected as the audio
language.
- Some discs may not contain the language you select
as your initial language; in that case the disc will use its
original language setting.
- The language is selected and the screen returns to
setup menu.
- To make the setup menu disappear, press the MENU
button.
LANGUAGE SETUP
Player Menu
Disc Menu
: English
√ Automatic
: English
English
Audio
: English
Deutsch
: English
Subtitle
Italiano
Enter
26
Downloaded from www.Manualslib.com manuals search engine
Return
Menu
Enter
Return
Menu
❶ Dolby Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bitstream : Outputs Dolby Digital via the digital output.
Select Bitstream when connecting to a Dolby Digital
Decoder.
❷ MPEG-2 Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bitstream : Converts to MPEG-2 Digital Bitstream
(5.1CH or 8CH). Select Bitstream when using the
Digital Audio Output.
❸ Dynamic Compression
- On : To select dynamic compression.
- Off : To select the standard range.
❹ PCM Down Sampling
- On : Select this when the Amplifier connected to the
player is not 96KHz compatible. In this case, the
96KHz signals will be down converted to 48KHZ.
- Off : Select this when the Amplifier connected to the
player is 96KHz compatible. In this case, all signals will
be output without any changes.
❶ TV Aspect
Depending on a type of television you have, you may
want to adjust the screen setting (aspect ratio).
- 4:3 Letter Box : Select when you want to see the total
16:9 ratio screen DVD supplies, even though you
have a TV with a 4:3 ratio screen. Black bars will
appear at the top and bottom of the screen.
- 4:3 Pan&Scan : Select this for conventional size TVs
when you want to see the central portion of the 16:9
screen. (Extreme left and right side of movie picture
will be cut off.)
- 16:9 Wide : You can view the full 16:9 picture on your
wide screen TV.
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby
Laboratories.
DISPLAY SETUP
TV Aspect
Aspect
Ratio
: 16:9 Wide
4:3 Letter Box
: Auto
4:3 Pan&Scan
Screen Messages : On
√ 16:9 Wide
Black Level
: On
Still Mode
“DTS Digital OutTM” is trademarks of Digital
Theater Systems, Inc.
❷
Display options enable you to set various video
functions of the player.
: I-SCAN
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
Menu
Return
Menu
Still Mode
These options will help prevent picture shake in still
mode and display small text clearer.
- Auto : When selecting Auto, Field/Frame mode will be
automatically converted.
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Display Setup, then press
3. Press the œ/ƒ
the ‹ or ENTER button.
ƒ buttons to select the desired item, then
4. Press the œ/ƒ
press the ‹ or ENTER button.
Return
: NTSC
Video Output
Enter
Setting Up the Display
Options
Enter
TV System
- Field : Select this feature when the screen shakes in
the Auto mode.
- Frame : Select this feature when you want to see
small letters more clearly in the Auto mode.
❸ Screen Messages
Use to turn on-screen messages On or Off.
❹
Black Level
Adjusts the brightness of the screen.(On or Off) It does
not function in Progressive mode.
❺ TV System
- NTSC : In case of using NTSC disc
• If your TV system only has PAL-Video input, you must
choose “PAL”. When you choose “PAL”, Interlace output format is PAL 60 Hz output.
• If your TV system only has NTSC, input you must
choose “NTSC ”.
- PAL : In case of using PAL disc
• If your TV system only has NTSC-Video input, you
must choose “NTSC”.
• If your TV system only has PAL input, you must
choose “PAL ”.
DISPLAY SETUP
TV Aspect
: Wide
Still Mode
: Auto
Screen Messages
: On
Black Level
TV System
Video Output
Enter
: Off
PAL
√ :NTSC
COMPOSIT
:PAL
Return
Menu
27
Downloaded from www.Manualslib.com manuals search engine
English
Note
• Even when PCM Down sampling is Off
• Some discs will only output down sampled
audio through the digital outputs.
• To make the Setup menu disappear, press the
MENU button.
• There is no analog audio output when you play
a DTS sound disc.
➏ Video Output
Select Video Output.
- Component (I-SCAN) : Select when you want to use
Component Interlace (525i) Out.
- Component (P-SCAN) : Select when you want to use
Component Progressive (525p) Out.
• If the Yes/No selection in the Display Setup sub Menu
is not made within 10 seconds, the screen returns to
the previous menu.
ƒ buttons to select Parental Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
Enter
Return
Menu
DISPLAY SETUP
TV Aspect
: Wide
Still Mode
: Auto
Screen Messages
: On
Black Level
: Off
TV System
ƒ buttons to select Rating Level, then press
4. Press the œ/ƒ
the ‹ or ENTER button.
PARENTAL SETUP
: PAL
√ I -SCAN
COMPOSIT/SVID ‹
:P-SCAN
Video Output
Rating level
: Kids Safe
Change Password
Enter
Return
Menu
• Consult your TV User’s Manual to find
out if your TV supports Progressive Scan. If
Progressive Scan is supported, follow the TV
User’s Manual regarding Progressive Scan
settings in the TV’s menu system.
• If Video Output is set incorrectly, the screen
may be blocked.
Enter
Return
Menu
5. Enter your password.
- By default, password is set to 0000.
PARENTAL SETUP
Rating Level
Setting Up the Parental
Control
Enter Password
The Parental Control function works in conjunction
with DVDs that have been assigned a rating, which
helps you control the types of DVDs that your family
watches. There are up to 8 rating levels on a disc.
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
28
Downloaded from www.Manualslib.com manuals search engine
Return
Enter
Return
Menu
ƒ buttons to select the Rating Level you want,
6. Press the œ/ƒ
then press the ‹ or ENTER button.
e.g) Setting up in Kids Safe.
Setting Up the Rating Level
Enter
: Kids Safe
Change Password
Menu
PARENTAL SETUP
Rating Level
Level
Rating
: Kids Safe
√ Kids Safe
Change Password Level 2
Level 3
Level 4
Level 5
Level 6
Enter
Return
Menu
Note:
- For example, if you select up to Level 6, discs
that contain Level 7,8 will not play.
• To make the setup menu disappear, press the
MENU button.
Changing the Password
PARENTAL SETUP
Rating Level
:Kids Safe
Change Password
Enter New Password
Enter
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
Enter
Return
Return
Menu
Note
If you have forgotten your password, see
“Forgot Password” in the Troubleshooting Guide.
Menu
ƒ buttons to select Parental Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
Enter
Return
Menu
ƒ button to select Change Password, then
4. Press the œ/ƒ
press the ‹ or ENTER button. Enter your password (default
password). Enter the new password.
PARENTAL SETUP
Rating Level
:Kids Safe
Change Password
Enter
Return
Menu
PARENTAL SETUP
Rating Level
:Kids Safe
Change Password
Enter Password
Enter
Return
Menu
29
Downloaded from www.Manualslib.com manuals search engine
English
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
REFERENCE
Troubleshooting
Before requesting service (troubleshooting), please check the following.
Action
Problem
Page
No operations can be
performed with the
remote control.
• Check the batteries in the remote control.
They may need replacing.
• Operate the remote control at a distance of no more than 20 feet.
• Remove batteries and hold down one or more buttons for several minutes to drain
the microprocessor inside the remote control to reset it. Reinstall batteries and try
to operate the remote control again.
P3
Disc does not play.
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the DVD.
P5
5.1 channel sound is
not being reproduced.
The
icon appears
on screen.
• 5.1 channel sound is reproduced only when the following conditions are met :
1) The DVD player is connected with the proper Amplifier
2) The disc is recorded with 5.1 channel sound.
• Check whether the disc being played has the “5.1 ch” mark on the outside.
• Check if your audio system is connected and working properly.
• In SETUP Menu, is the Audio Output set to Bitstream?
P 12-13
P26~27
• The features or action cannot be completed at this time because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
Disc Menu doesn’t appear. • Check if the disc has a Menu.
Play mode differs from the • Some of the functions selected in the Setup Menu may not work properly if the
Setup Menu selection.
disc is not encoded with the corresponding function.
P25~29
The screen ratio
cannot be changed.
• The Screen Ratio is fixed on your DVDs.
P27~28
No audio.
• Make sure you have selected the correct Digital Output in the Audio Options
Menu.
P26~27
The screen is blocked
• Press the
button (on front panel) for more than 5 seconds under no disc
inside. All settings will revert to the factory settings.
Forgot password
• Press the
button (on front panel ) for more than 5 seconds under no disc
inside. All settings including the password will revert to the factory settings. Don't
use this unless absolutely necessary.
Other problems.
• Go to the contents of the instruction book and find the section that contains the
explanations regarding the current problem, and follow the procedure once again.
• If the problem still cannot be solved, please contact your nearest authorized service center.
The picture is noisy or
distorted
• Make sure that the disc is not dirty or scratched.
• Clean the disc.
30
Downloaded from www.Manualslib.com manuals search engine
P14
P28
P2
USB HOST Feature
Supported Products
USB Flash Disk
Product
Finepix-A340
Finepix-F810
Finepix-F610
Finepix-f450
Finepix S7000
Finepix A310
KD-310Z
Finecam SL300R
Finecam SL400R
Finecam S5R
Finecam Xt
Dimage-Z1
Dimage Z1
Dimage X21
Coolpix4200
Coolpix4300
Coolpix 2200
Coolpix 3500
Coolpix 3700
Coolpix 4100
Coolpix 5200
Stylus 410 digital
300-digital
U300
X-350
C-760
C-5060
X1
U-mini
Lumix-FZ20
DMC-FX7GD
Lumix LC33
LUMIX DMC-F1
Optio-S40
Optio-S50
Optio 33LF
Optio MX
Digimax-420
Digimax-400
Sora PDR-T30
Coolpix 5900
Coolpix S1
Coolpix 7600
DMC-FX7
Dimage Xt
AZ-1
Company
Fuji
Fuji
Fuji
Fuji
Fuji
Fuji
Konica
Kyocera
Kyocera
Kyocera
Kyocera
Minolta
Minolta
Minolta
Nikon
Nikon
Nikon
Nikon
Nikon
Nikon
Nikon
Olympus
Olympus
Olympus
Olympus
Olympus
Olympus
Olympus
Olympus
Panasonic
Panasonic
Panasonic
Panasonic
Pentax
Pentax
Pentax
Pentax
Samsung
Samsung
Toshiba
Nikon
Nikon
Nikon
Panasonic
Minolta
Olympus
Type
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Company
Sandisk
Cruzer Mini
Cruzer Mini
SONY Micro Vault
FLEX DRIVE
AnyDrive
XTICK
Micro Mini
iFlash
LG
RiDATA
Type
USB 2.0 USB Flash
Drive 128M
USB 2.0 128M
USB 2.0 256M
USB 2.0 64MB
USB 2.0 32MB
USB 2.0 128MB
USB 2.0 128M
USB 2.0 128M
USB 2.0 64M
USB 2.0 64M
USB 2.0 64M
Sandisk
Sandisk
Sony
Serotech
A.L tech
LG
Iomega
Imation
XTICK(M)
EZDrive
MP3 Player
Product
Company
Creative MuVo NX128M
Iriver H320
YH-920
YP-T7
YP-MT6
YP-T6
YP-53
YP-ST5
YP-T5
YP-60
YP-780
YP-35
YP-55
iAUDIO U2
iAUDIO G3
iAudio M3
SI-M500L
H10
YP-T5 VB
YP-53
Type
Creative
Iriver
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Cowon
Cowon
Cowon
Sharp
Iriver
Samsung
Samsung
128 MB MP3 Player
20G HDD MP3 Player
20G HDD MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
HDD MP3 Player
256MB MP3 Player
MP3 Player
MP3 Player
256MB MP3 Player
Multi Card Reader
Product
UNICORN
USB 2.0 Card Reader
Company
Type
Unicorn
Billionton(Taiwan)
USB 2.0 7 IN 1 CARD
READER UC-601R
USB 2.0 Card Reader for
SD/MMC/RS-MMC(3-in-1)
USB External HDD
Product
CUTIE
MOMOBAY UX-2
Company
Serotech
Dvico
Type
POCKET HARD DISK DRIVE
USB 2.0
31
Downloaded from www.Manualslib.com manuals search engine
English
Digital Camera
Product
Cruzer Micro
Specifications
General
Power Requirements
AC 110-240 V, 60/50 Hz
Power Consumption
9W
Weight
Dimensions
1.5 Kg
430mm (W) X 207mm (D) X 37mm (H)
Operating Temperature Range
+5°C to +35°C
Operating Humidity Range
10 % to 75 %
DVD
(DIGITAL VERSATILE DISC)
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time
(Single Sided, Single Layer Disc) : 135 min.
CD : 12Cm
Disc
(COMPACT DISC)
CD : 8Cm
(COMPACT DISC)
VCD : 12Cm
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min. (Video + Audio)
Composite Video
Video
Output
1 channel : 1.0 Vp-p (75 Ω load)
Y : 1.0 Vp-p (75 Ω load)
Component Video
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
2 Channel
Audio
*Frequency Response
Output
*Dynamic Range
L(1/L), R(2/R)
48 kHz Sampling : 4 Hz to 22 kHz
96 kHz Sampling : 4 Hz to 44 kHz
100 dB
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
- Weight and dimensions are approximate.
32
Downloaded from www.Manualslib.com manuals search engine
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer
care center.
Region
North America
Latin America
Country
CANADA
MEXICO
U.S.A
ARGENTINE
BRAZIL
CHILE
NICARAGUA
HONDURAS
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD & TOBAGO
VENEZUELA
COLOMBIA
BELGIUM
CZECH REPUBLIC
DENMARK
FINLAND
FRANCE
Europe
CIS
Asia Pacific
Middle East &
Africa
GERMANY
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
POLAND
PORTUGAL
SLOVAKIA
SPAIN
SWEDEN
U.K
EIRE
AUSTRIA
SWITZERLAND
RUSSIA
KAZAHSTAN
UZBEKISTAN
KYRGYZSTAN
TADJIKISTAN
UKRAINE
LITHUANIA
LATVIA
ESTONIA
AUSTRALIA
NEW ZEALAND
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
PHILIPPINES
SINGAPORE
THAILAND
TAIWAN
VIETNAM
TURKEY
Customer Care Center 1-800-SAMSUNG(726-7864)
01-800-SAMSUNG(726-7864)
1-800-SAMSUNG(726-7864)
0800-333-3733
0800-124-421 , 4004-0000
800-SAMSUNG(726-7864)
00-1800-5077267
800-7919267
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
1-800-234-7267
800-7267
1-800-682-3180
1-800-751-2676
1-800-SAMSUNG(726-7864)
0-800-100-5303
01-8000112112
0032 (0)2 201 24 18
844 000 844
Distributor pro Českou republiku:
Samsung Zrt., česka organizační složka
Vyskočilova 4, 14000 Praha 4
70 70 19 70
030-6227 515
3260 SAMSUNG ( 0,15/Min),
08 25 08 65 65 ( 0,15/Min)
01805 - SAMSUNG(726-7864) (
06-80-SAMSUNG(726-7864)
800-SAMSUNG(726-7864)
0035 (0)2 261 03 710
Web Site
www.samsung.com/ca
www.samsung.com
www.samsung.com
www.samsung.com/ar
www.samsung.com
www.samsung.com/cl
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com.co
www.samsung.com/be
www.samsung.com/cz
www.samsung.com/dk
www.samsung.com/fi
www.samsung.com
0,14/Min)
0900-SAMSUNG(726-7864) ( 0,10/Min)
815-56 480
0 801 801 881 , 022-607-93-33
80820-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
902 10 11 30
0771-400 200
0845 SAMSUNG (7267864)
0818 717 100
0800-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
8-800-555-55-55
8-10-800-500-55-500
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
8-800-502-0000
8-800-77777
800-7267
800-7267
1300 362 603
0800SAMSUNG(726-7864)
800-810-5858 , 010-6475 1880
3698-4698
3030 8282 , 1800 110011
0800-112-8888
0120-327-527
1800-88-9999
1800-10-SAMSUNG(726-7864)
1800-SAMSUNG(726-7864)
1800-29-3232 , 02-689-3232
0800-329-999
1 800 588 889
444 77 11
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/be
www.samsung.com/nl
www.samsung.com/no
www.samsung.com/pl
www.samsung.com/pt
www.samsung.com/sk
www.samsung.com
www.samsung.com/se
www.samsung.com
www.samsung.com/ie
www.samsung.com/at
www.samsung.com/ch
www.samsung.com
www.samsung.kz
www.samsung.uz
www.samsung.com
www.samsung.lt
www.samsung.com/lv
www.samsung.ee
www.samsung.com
www.samsung.com/nz
www.samsung.com
www.samsung.com/hk
www.samsung.com
www.samsung.com
www.samsung.com/jp
www.samsung.com/my
www.samsung.com/ph
www.samsung.com
www.samsung.com
www.samsung.com/tw
www.samsung.com
www.samsung.com
SOUTH AFRICA
0860-SAMSUNG(726-7864 )
www.samsung.com
U.A.E
800-SAMSUNG (726-7864), 8000-4726
www.samsung.com
Downloaded from www.Manualslib.com manuals search engine
Memo
Downloaded from www.Manualslib.com manuals search engine
Memo
Downloaded from www.Manualslib.com manuals search engine
Memo
Downloaded from www.Manualslib.com manuals search engine
Memo
Downloaded from www.Manualslib.com manuals search engine
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products,
please contact the SAMSUNG customer care centre.
1800 10-SAMSUNG (726-7864)/ www.samsung.com/ph
AK68-01506L
Downloaded from www.Manualslib.com manuals search engine
Download PDF