Z100 / Z300
Z500
Z700
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW TREADMILL!
Table of Contents
Product Registration…………………………………………………………………………. 2
Important Safety Instructions………………………………………………………………… 3
Important Electrical Information………………………………………………………………4
Important Operation Instructions……………………………………………………………..5
Assembly instructions………………………………………………………………………….6
Folding Instructions…………………………………………………………………………….8
Operation of Your New Treadmill……………………………………………………………. 9
Programmable Features……………………………………………………………………….11
Target Heart Rate……………………………………………………………………………… 15
Maintenance of Your New Treadmill………………………………………………………….16
Service Checklist - Diagnosis Guide…………………………………………………………. 18
Manufacturer’s Limited Warranty………………………………………………………………19
ATTENTION-THIS TREADMILL IS INTENDED FOR RESIDENTIAL USE ONLY
AND IS WARRANTED FOR THAT APPLICATION. ANY OTHER APPLICATION
VOIDS THIS WARRANTY IN ITS ENTIRETY.
1
Z8
CONGRATULATIONS ON YOUR
NEW TREADMILL AND WELCOME
TO THE SPIRIT FAMILY!
Thank you for your purchase of this quality treadmill from Spirit Manufacturing,
Inc. Your new treadmill was manufactured by one of the leading fitness
manufacturers in the world and is backed by one of the most comprehensive
warranties available. Through your dealer, Spirit will do all we can to make your
ownership experience as pleasant as possible for many years to come. The local
dealership where you purchased this treadmill is your administrator for all Spirit
warranty and service needs. Their responsibility is to provide you with the
technical knowledge and service personnel to make your experience more
informed and any difficulties easier to remedy.
Please take a moment at this time to record the name of the dealer, their
telephone number, and the date of purchase below to make any future, needed
contact easy. We appreciate your support and we will always remember that you
are the reason that we are in business. Please complete and mail your
registration card today and enjoy your new treadmill.
Yours in Health,
Spirit Manufacturing, Inc.
Name of Dealer______________________________________
Telephone Number of Dealer___________________________
Purchase Date_______________________________________
Product Registration
RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this fitness product in the space provided below.
Serial Number_______________________________________
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to
Spirit Manufacturing, Inc or visit www.spiritfitness.com to register online.
2
Z8
Important Safety Instructions
WARNING - Read all instructions before using this appliance.
DANGER - To reduce the risk of electric shock disconnect your Spirit treadmill
from the electrical outlet prior to cleaning and/or service work.
WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons,
install the treadmill on a flat level surface with access to a 120-volt, 20-amp
grounded outlet.
DO NOT USE AN EXTENSION CORD: DO NOT ATTEMPT TO DISABLE THE
GROUNDED PLUG BY USING IMPROPER ADAPTERS, OR IN ANY WAY MODIFY
THE CORD SET. A serious shock or fire hazard may result along with computer
malfunctions. See Grounding Instructions, page 4.
■ Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both
carpet and treadmill may result.
■ Do not block the rear of the treadmill. Provide a minimum of 3 1/2 feet clearance
between the rear of the treadmill and any fixed object.
■ Keep children away from the treadmill. There are obvious pinch points and other
caution areas that can cause harm.
■ Keep hands away from all moving parts.
■ Never operate the treadmill if it has a damaged cord or plug. If the treadmill is not
working properly, call your dealer.
■ Keep the cord away from heated surfaces.
■ Do not operate where aerosol spray products are being used or where oxygen is
being administered. Sparks from the motor may ignite a highly gaseous
environment.
■ Never drop or insert any object into any openings.
■ Do not use outdoors.
■ To disconnect, turn all controls to the off position, remove tether cord, then remove
the plug from the outlet.
■ Do not attempt to use your treadmill for any purpose other than for the purpose it is
intended.
■ The pulse sensors are not medical devices. Various factors, including the user’s
movement, may affect the accuracy of heart rate readings. The pulse sensors are
intended only as exercise aids in determining heart rate trends in general.
■ Use handrails provided; they are for your safety.
■ Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable
for use on your treadmill. Quality athletic shoes are recommended to avoid leg
fatigue.
Remove tether cord after use to prevent unauthorized treadmill operation.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
3
Z8
Important Electrical Information
WARNING!
● NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill.
Route the power cord away from any moving part of the treadmill including the elevation
mechanism and transport wheels.
● NEVER remove any cover without first disconnecting AC power.
● If voltage varies by ten percent (10%) or more, the performance of your treadmill may
be affected. Such conditions are not covered under your warranty. If you suspect
the voltage is low, contact your local power company or a licensed electrician for proper
testing. See Diagnosis Guide, page 20.
● NEVER expose this treadmill to rain or moisture. This product is NOT designed for
use outdoors, near a pool or spa, or in any other high humidity environment.
Grounding Instructions
This product must be grounded. If the treadmill should malfunction or breakdown,
grounding provides a path of least resistance for electric current, reducing the risk of
electric shock. This product is equipped with a cord having an equipment-grounding
plug. The plug must be plugged into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result
in a risk of electric shock. Check with a qualified electrician or serviceman if you
are in doubt as to whether the product is properly grounded. Do not modify the
plug provided with the product if it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks
like the plug illustrated below. A temporary adapter that looks like the adapter illustrated
below may be used to connect this plug to a 2-pole receptacle as shown below if a
properly grounded outlet is not available. The temporary adapter should be used only
until a properly grounded outlet (below) can be installed by a qualified electrician. The
green colored rigid ear-lug, or the like, extending from the adapter, must be connected
to a permanent ground such as a properly grounded outlet box cover. Whenever the
adapter is used, it must be held in place by a metal screw.
Adapter
Grounded Outlet
Metal Screw
Grounding Pin
Tab of
Grounding
Screw
Grounded Outlet Box
4
Z8
Important Operation Instructions
NEVER operate this treadmill without reading and completely understanding the
results of any operational change you request from the computer.
● Understand that changes in speed and incline do not occur immediately. Set your
desired speed on the computer console and release the adjustment key. The
computer will obey the command gradually.
● NEVER use your treadmill during an electrical storm. Surges may occur in your
household power supply that could damage treadmill components.
● Use caution while participating in other activities while walking on your treadmill; such
as watching television, reading, etc. These distractions may cause you to lose
balance or stray from walking in the center of the belt; which may result in serious
injury.
● NEVER mount or dismount the treadmill while the belt is moving. Spirit treadmills
start at a very low speed and it is unnecessary to straddle the belt during start up.
Simply standing on the belt during slow acceleration is proper after you have learned
to operate the unit.
● Always hold on to a handrail or hand bar while making control changes (incline,
speed, etc.).
Do not use excessive pressure on console control keys. They are precision set to
function properly with little finger pressure. Pushing harder is not going to make the unit
go faster or slower. If you feel the buttons are not functioning properly with normal
pressure contact your Spirit dealer.
●
Safety Tether Cord
A safety tether cord is provided with this unit. It is a simple magnetic design that should
be used at all times. It is for your safety should you fall or move too far back on the
tread-belt.
Pulling this safety tether cord will stop tread-belt movement.
To Use:
1. Place the magnet into position on the round metal portion of the console control head.
Your treadmill will not start and operate without this. Removing the magnet also
secures the treadmill from unauthorized use.
2. Fasten the plastic clip onto your clothing securely to assure good holding power.
Note: The magnet has strong enough power to minimize accidental, unexpected
stopping. The clip should be attached securely to make certain it does not come off. Be
familiar with its function and limitations. The treadmill will stop, depending on speed,
with a one to two step coast anytime the magnet is pulled off the console. Use the red
Stop / Pause switch in normal operation.
5
Z8
Assembly Instructions (Z8)
6
Z8
ASSEMBLY PACK CHECK LIST (Z8)
5/16”x18x1.5T Flat Washer (x4)
5/16”x23x1.5T Curve Washer (x4)
5/16”x1/2”Button Head Socket Screw (x12)
Safety Key (x1)
Lubricant (x1)
M5 Allen Wrench (x1)
M6 Allen Wrench (x1)
Assembly (Z8)
■ STEP 1
Remove all parts from the carton.
■ STEP 2
Connect Computer Cable (Lower) with Computer Cable (Middle).
■ STEP 3
Hand tighten the Right and Left Handrails into the Frame Base with 8 pcs of 5/16” x
1/2” Button Head Socket Screws, 4 pcs of 5/16” x 18 x 1.5T Flat Washers and 4 pcs of
5/16”x 23 x 1.5T Curve Washers by using the M5 Allen Wrench.
■ STEP 4
Connect Computer Cable (Middle) with Computer cable (Upper).
Connect Speed Adjustment Switch w/Cable with Speed Cable (Upper).
And connect Incline Adjustment Switch w/Cable with Incline Cable (Upper).
■ STEP 5
Install the Console Support into the Right and Left Handrails with 4 pcs of 5/16” x 1/2”
Button Head Socket Screws by using M5 Allen Wrench.
■ PLEASE LOCK DOWN ALL HARDWARE AFTER THE ACCESSSORIES HAVE
BEEN ASSEMBLED.
7
Z8
Z8 Folding Instructions
Do not attempt to move the unit unless it is in the folded and locked position. Be sure the
power cord is secured to avoid possible damage. Use both handrails to maneuver the unit
to the desired position.
■ To Fold The Treadmill:
Ensure the incline angle of the treadmill is at its lowest position. Lift the treadmill running
board up until locking knob install into the hole.
■ To Unfold The Treadmill:
Hold the treadmill running board with left hand. Pull the locking knob with your right hand
and slowly lower the treadmill running board. *Remove your right hand as you slowly lower
the running board to the floor.
Transport
■ Z8
The treadmill is equipped with four transport wheels which are engaged when the treadmill
is folded. After folding simply roll the treadmill away.
8
Z8
Operation of Your Treadmill
Getting familiar with the control panel
■ Z8 Console
INITIAL DISPLAY:
ODO: Displays total accumulated working distance in DISTANCE window from 0.00 to
999 miles.
HRS: Displays total accumulated working time in TIME window from 0 to 99:99.
If exceed 99:99 minutes window will display by hour from 1 to 9999.
VER: Displays current software version in SPEED window.
9
Z8
WINDOW DISPLAY:
DISTANCE: Accumulates total workout distance from 0.00 to 99.99 miles.
TIME:
Accumulates total workout time from 00:00 to 99:59.
CALORIES: Accumulates the user’s calorie consumption during exercise. Max. Value
is 999.9 calories.
SPEED:
Displays the current running speed from 0.5Mph- 10Mph.
PULSE:
Displays your current heart rate in beats per minute during workout.
If computer doesn’t receive heart rate input, dot will not flash on the side
of P.
INCLINE:
Displays your current workout elevation from 0 to 10.
LAPS/PROGRAM: Accumulates total Laps from L00 to L99 and displays your current
workout program you can press “MODE” button to exchange
display window.
LUBE: Reminds user to apply silicon lubricant between the belt and deck. If “ODO” or
“HRS” achieve target where “HRS” is 180 hours and “ODO” is 600 miles window
will display “LUBRICATE DECK”. If reminded a third time, it will display “PRESS
MODE 3 SECONDS TO CANCEL THIS MESSAGE”.
FUNCTION BUTTONS:
START: Press “START” button to start training.
STOP: Press “STOP” button to stop training and press for 3 seconds to clear all screen
data.
FAST: Press “FAST’ button to increase your speed.
SLOW: Press “SLOW” button to decrease your speed.
UP: Press “UP” button to increase elevation position.
DOWN: Press “DOWN” button to decrease elevation position.
MODE: Press “MODE” button to select different setting mode in STOP or PROGRAM
mode.
SELECT: Press “SELECT” button to choose type of profile display. Before running, you
can display either speed or incline or display two profiles at same time in
PROGRAM mode.
PROGRAM: Press program buttons to choose training mode.
SAFETY KEY: Put safety key in position to power on the computer. When safety key is
pulled away from its position, the computer will automatically shut down.
10
Z8
QUICK SPEED KEYS:
5 preset buttons for rapid speed: 2Mph, 4Mph, 6Mph, 8Mph,10Mph. User can press the
5 buttons, mentioned above, at any time, to start treadmill and treadmill will
automatically adjust to preset speed.
QUICK INCLINE KEYS:
5 preset buttons for rapid incline: 2, 4, 6, 8, 10. User can press the 5 buttons, mentioned
above, at any time, to start treadmill and treadmill will automatically adjust to preset
elevation.
CONSOLE OPERATION:
1. Put the safety key in position and all data will be displayed then the major screen will
show ODO, HRS, VER. User can press any buttons to enter next step. When
treadmill has started, above values will accumulate. Pressing “STOP” button will end
exercise session.
2. Press any pre-set program you like then press “START” button to begin the program.
3. While exercising, you can press FAST/SLOW button to adjust the speed manually.
4. While exercising, you can press “STOP” button to stop your workout or pull safety
key away from its position to shut down the computer.
5. If after pressing “STOP” button to stop the treadmill, and you want to resume your
workout, you can press “START” button again to start the treadmill then all previous
data will resume counting.
Programmable Features
MANUAL
Step 1. Press “MANUAL” button and press “START” button to start running.
Step 2. Before running, press “MODE” button to set the count down time. Range is from
10:00 to 99:00, set the count down distance; range is from 0.10 to 99.90 or set
the count down calories; range is from 1.0 to 999.0. Whenever any program
counts down to zero the treadmill will stop. Press “START” button to restart
training then treadmill will restart and target will count down, other data will
count up. If you do not set count down, console will count up from zero.
Step 3. During running, user can adjust the speed by pressing “FAST/SLOW” or press
rapid keys to adjust SPEED manually.
Step 4. Press “STOP” button to stop your workout or pull safety key away from its
position to shut down the computer.
11
Z8
P1 ~ P5 (PRESET PROGRAM)
Step 1. Press any button to choose P1 ~ P5 in “STOP” mode, each program has a
preset speed and incline value.
Step 2. Press “MODE” button to set the count down time from 10:00 to 99:00. User can
adjust by pressing “FAST/SLOW”. If you do not set the count down, console will
count up from zero. Or press “START” button immediately to start training. Time
is limited to 20 minutes wherein total segments are 20 and each segment
exercising time is 1 minute. Press “MODE” button again to set MAX. speed of
profile from 5.0Mph to 8.0Mph.
Step 3. After setting, press “START” button to start training, treadmill will start a 3
minutes warm up. Or you can press “START” button again to enter exercising
immediately. Treadmill will adjust the SPEED in accordance with profile. You
can press “STOP” button to stop training during operation. Only Speed goes to
zero, other data will save original data. If you don’t clear, press “START” button
to save last time values.
*After running you can exchange speed and incline profile, press “UP/DOWN”
to change to INCLINE profile and press “FAST /SLOW” to change to SPEED
profile.
Step 4. When time counts down to zero, treadmill will be 3 minute cool down. Or press
“STOP” button to stop training immediately and a series of beeps will indicate
end of program.
USER 1 ~ USER 3
Step 1. Choose User 1 ~ User 3.
Step 2. Press “MODE” button to set time. You can adjust by pressing “FAST/SLOW”.
Step 3. Press “MODE” button again to set speed, first segment will flash and press
“FAST/SLOW” button to adjust speed, press “UP/DOWN” button to enter incline
programming then press “UP/DOWN” again to adjust. Press “MODE” button to
enter next segment.
Step 4. After setting, press “START” button to start training, treadmill will adjust the
SPEED and INCLINE in accordance with profile. User can press “STOP” button
to stop training during operation and window will save last values. If last time is
COUNT UP, press “START” to continue COUNT UP and other data will COUNT
DOWN.
12
Z8
H.R.C. (H1 ~ H2)
Step 1. Choose H1 or H2.
Step 2. Press “MODE” button to set time. The range is from 10:00 to 99:00 and press
“FAST/SLOW” to adjust. If you do not set the count down, console will count up
from zero.
Step 3. Press “MODE” button again to set “AGE” in PULSE window. The range is from
10 to 99 and preset value is 30. Press “FAST/SLOW” button to adjust then
window will calculate the T.H.R as below formula:
H1 = (220-age)*60% = TARGET HEART RATE
H2 = (220-age)*80% = TARGET HEART RATE
Step 4. After calculating, if you want to change T.H.R, press “MODE” button to enter
setting “T.H.R” in PULSE window the range is from 60 to 220. Press
“FAST/SLOW” button to adjust.
Step 5. If setting is finished, press START and place both hands on the handpulse grips
to start your workout.
Step 6. If your heart rate doesn’t achieve set value (T.H.R), the treadmill will increase
INCLINE height automatically until user achieves target value. Then treadmill
will adjust incline UP/DOWN to maintain your T.H.R..
ERROR MESSAGE:
1.
LS: Treadmill doesn’t receive the speed signal for 8 seconds.
2.
E2: Incline position error.
3.
Err: Memory of console malfunction or CPU accessing problem.
13
Z8
*SPEED PROFILE
*INCLINE PROFILE
P1 SPEED PROFILE
P1 INCLINE PROFILE
P2 SPEED PROFILE
P2 INCLINE PROFILE
P3 SPEED PROFILE
P3 INCLINE PROFILE
P4 SPEED PROFILE
P4 INCLINE PROFILE
P5 SPEED PROFILE
P5 INCLINE PROFILE
14
Z8
Target Heart Rate
The old motto, “no pain, no gain”, is a myth that has been overpowered by the
benefits of exercising comfortably. A great deal of this success has been promoted by
the use of heart rate monitors. With the proper use of a heart rate monitor, many people
find that their choice of exercise intensity is either too high or too low and exercise is
much more enjoyable by maintaining their heart rate in the desired benefit range.
●
To determine the benefit range in which you wish to train, you must first determine
your Maximum Heart Rate.
This can be accomplished
by using the following
formula: 220 - User’s Age =
Maximum Heart Rate. If you
enter your age during
programming of the console
the console will perform this
calculation automatically.
This is used for the HR
control programs and also
for the Heart rate bar graph
(Z500/Z700 only). After
calculating your Maximum
Heart Rate, you can decide
upon which goal you would
like to pursue. The two most
popular reasons for, or
goals of exercise, are
cardiovascular fitness
(training for the heart and
lungs) and weight control. The black columns on the chart above represent the
Maximum Heart Rate for a person whose age is listed at the bottom of each column.
The training heart rate, for either cardiovascular fitness or weight loss, is represented by
two different lines that cut diagonally through the chart. A definition of the lines’ goal is in
the bottom left-hand corner of the chart. If your goal is cardiovascular fitness or if it is
weight loss, it can be achieved by training at 90% or 70%, respectively, of your
Maximum Heart Rate on a schedule approved by your physician. Consult your physician
before participating in any exercise program.
With all Spirit Heart Rate Control treadmills, you may use the heart rate monitor feature
without using the Heart Rate Control program. This function can be used during manual
mode or during any of the nine different programs. The Heart Rate Control program
automatically controls incline.
●
CAUTION!
The target value used in H-1 and H-2 programs is a suggestion only for normal, healthy
individuals. Do not exceed your limits! You may not be able to obtain your chosen target.
If in question, enter a higher age value that will set a lower target goal.
15
Z8
General Maintenance
Belt and Bed - Your treadmill uses a very high-efficient low-friction bed. Performance is
maximized when the bed is kept as clean as possible. Use a soft, damp cloth or paper
towel to wipe the edge of the belt and the area between the belt edge and frame. Also
reach as far as practical directly under the belt edge. This should be done once a month
to extend belt and bed life. Use water only - no cleaners or abrasives. A mild soap and
water solution along with a nylon scrub brush will clean the top of the textured belt.
Allow to dry before using.
Belt Dust - This occurs during normal break-in or until the belt stabilizes. Wiping excess
off with a damp cloth will minimize buildup.
General Cleaning - Dirt, dust, and pet hair can block air inlets and accumulate on the
running belt. On a monthly basis, vacuum underneath your treadmill to prevent buildup.
Once a year, you should remove the black motor hood and vacuum out dirt that may
accumulate. UNPLUG POWER CORD BEFORE THIS TASK.
BELT ADJUSTMENTS:
During use, if you notice that walking belt either shifts to the right or the left of center, first
remove "Safety Key" and unplug equipment from AC power source. Using the M6 Allen
wrench provided, turn left rear roller adjustment clockwise no more the 1/4" of a turn as
indicated above. Remove the M6 Allen wrench, insert "Safety Key" and insert AC power
cord into AC outlet. Turn on your treadmill and observe after running a few minutes to see if
problem has been corrected. This may take several adjustments, so repeat the above
procedure.
16
Z8
BELT / DECK LUBRICATION:
Do not re-lube with other than Spirit lubricant. Spirit provides one application with this
unit. See your Spirit dealer for additional purchases. The use of some other lubricants
may destroy the deck surface or belt and will void warranty. Conditions exist beyond
Spirit’s control on belt / deck cleanliness which relates to friction.
You should apply the enclosed belt lubrication after approximately the first 50 hours of
operation. Use all the contents of one container (no more) and spread lubricant onto
middle portion (away from edges) of the deck (under treadbelt) along its width. When
walked on, the belt will make certain an even coat is applied. Lubricant is not harmful to
the skin. Lube will be distributed properly by walking at 2 to 3 mph for 3 to 5 minutes on
all areas of the belt. Use handrails for support. The first few minutes you will be
polishing your deck and lubricating the belt backing. Do not run on a newly lubricated
belt until the above break-in procedure is done. If the treadmill belt/deck is kept
reasonably clean it is possible to expect over 1000 hours before additional re-lubing is
necessary.
CAUTION - KEEP HANDS CLEAR OF MOVING REAR PULLEY!
17
Z8
Service Checklist - Diagnosis Guide
Before contacting your dealer for aid, please review the following information. It may
save you both time and expense. This list includes common problems that may not be
covered under the treadmill’s warranty.
PROBLEM
Display does not light
Treadbelt does not stay centered
Treadmill belt hesitates when walked/run on
Motor is not responsive / Display is lit
Treadmill will only achieve approximately
7 mph but shows higher speed on display
SOLUTION/CAUSE
Tether cord not in position.
Circuit breaker on front grill tripped. Push circuit
breaker in until it locks.
Plug is disconnected. Make sure plug is firmly pushed
into AC household wall outlet.
Household circuit breaker may be tripped.
Treadmill defect. Contact your Spirit dealer.
A user may be walking while favoring or putting more
weight on either the left or right foot. If this walking
pattern is natural, track the belt slightly off-center to
the side opposite from the belt movement. See
General Maintenance section on Treadbelt Tension.
Adjust as necessary.
Make certain clock is running.
This indicates motor should be receiving power to
operate. Low AC voltage to treadmill. Do not use an
extension cord. If an extension cord is required it
should be as short as possible and heavy duty 16
gauge minimum. Low household voltage. Contact an
electrician or your Spirit dealer. A minimum of 110
volt AC current is required.
Treadbelt stops quickly/suddenly when
tether cord is pulled
High belt/deck friction. See General Maintenance
section on lubrication.
Treadmill trips on board 15amp circuit
High belt/deck friction. See General Maintenance
Computer shuts off when console is
touched (on a cold day)while walking/running
Treadmill is not grounded. Static electricity is
“crashing” the computer. Refer to Grounding
Instructions on page 4.
18
Z8
Manufacturer’s Limited Warranty
Effective October 15, 2004
TREADMILL WARRANTY
Spirit Manufacturing Inc. warrants all its treadmills’ parts for a period of 5 years from the date of retail sale, as determined by sale receipt,
or eighteen (18) months from the original factory shipping date, whichever comes first. Spirit’s responsibilities include providing new or
remanufactured parts, at Spirit’s option, and technical support to our independent dealers and servicing organizations. In the absence of
a dealer or service organization, these warranties will be administered by Spirit directly to a consumer. An extended warranty period
applies to the following components:
Drive Motor
Deck Wear
Electronics / Belt / Rollers
Frame Weldments
All Other Components
30 Years
5 Years
5 Years
Lifetime
5 Years
NORMAL RESPONSIBILITIES OF THE CONSUMER
This warranty applies only to products in ordinary household use, and the consumer is responsible for the items listed below:
1. The warranty registration card must be completed and returned to the address listed on the card within 10 days of the original
purchase to validate the manufacturer’s limited warranty.
2. Proper use of the treadmill in accordance with the instructions provided in this manual, including belt tracking.
3. Proper installation by an authorized Spirit service company in accordance with instructions provided with the treadmill and with all local
electric codes.
4. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose connections or defects
in house wiring.
5. Expenses for making the treadmill accessible for servicing, including any item that was not part of the treadmill at the time it was
shipped from the factory.
6. Damages to the treadmill finish during shipping, installation or following installation.
EXCLUSIONS
This warranty does not cover the following:
1. CONSEQUENTIAL, COLLATERAL, OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or
exclusion may not apply to you.
2. Service call reimbursement to the consumer. Service call reimbursement to the dealer that does not involve malfunction or
defects in workmanship or material, for units that are beyond the warranty period, for units that are beyond the service call
reimbursement period, for treadmills not requiring component replacement, or treadmills not in ordinary household use.
3. Damages caused by services performed by persons other than authorized Spirit service companies; use of parts other than original
Spirit parts; or external causes such as alterations, modifications, abuse, misuse, accident, improper maintenance, inadequate power
supply, or acts of God.
4. Products with original serial numbers that have been removed or altered.
5. Products that have been sold, transferred, bartered, or given to a third party.
6. Products that do not have a warranty registration card on file at Spirit Mfg. Spirit reserves the right to request proof of
purchase if no warranty record exists for the product.
7. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE.
SERVICE
Keep your bill of sale. Twelve (12) months from the date on the bill of sale or eighteen (18) months from the date of factory
shipping as determined by the serial number establishes the warranty period should service be required. If service is performed,
it is in your best interest to obtain and keep all receipts. This written warranty gives you specific legal rights. You may also have
other rights that vary from state to state. Service under this warranty must be obtained by following these steps, in order:
1. Contact your selling authorized Spirit dealer. OR
2. Contact your local authorized Spirit service organization.
3. If there is a question as to where to obtain service, contact our service department at (870) 935-1107.
4. If no local service is available, Spirit will repair or replace the parts, at Spirit’s option, within the warranty period at no charge
for parts. All transportation costs, both to our factory and upon return to the owner, are the responsibility of the owner. The
owner is responsible for adequate packaging upon return to Spirit. Spirit is not responsible for damages in shipping. Make all
freight damage claims with the appropriate freight carrier. DO NOT SHIP ANY UNIT TO OUR FACTORY WITHOUT A RETURN
AUTHORIZATION NUMBER. All units arriving without a return authorization number will be refused.
5. For any further information, or to contact our service department by mail, send your correspondence to:
Spirit Manufacturing, Inc.
P.O. Box 2037
Jonesboro, AR 72402-2037
Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by
Spirit Manufacturing, Inc. This warranty applies only in the 50 states of the U.S.A. and Canada.
19
Z8