Model No. No. de Modelo TH-60PF50U TH-65PF50U Operating Instructions High Denition Plasma Display Manual de instrucciones Pantalla de plasma de alta denición Contents Safety Instructions .................. 3 • Important FCC STATEMENT .................................. 4 • Safety Precautions ................................. 5 • Maintenance ........................................... 6 • Accessories............................................. 9 • Connections.......................................... 10 • Power ON / OFF .................................. 13 • Basic Controls....................................... 15 • Specifications........................................ 17 • Panasonic Professional Flat Panel • Display Limited Warranty ..................... 18 WARRANTY STATEMENT .... 19 • LIMITED Customer Service ................................. 20 • For more detailed instructions, refer to the Operating Instructions on the CD-ROM. Para obtener instrucciones más detalladas, consulte las instrucciones de manejo contenidas en el CD-ROM. English Español Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. Antes de conectar, utilizar o ajustar este producto, lea completamente este manual de instrucciones; y guárdelo para consultarlo en el futuro en caso de ser necesario. TQB2AA0670 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. No user-serviceable parts inside. Refer servicing to qualied service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the appliance. WARNING : To prevent damage which may result in re or shock hazard, do not expose this apparatus to rain or moisture. Do not place containers with water (ower vase, cups, cosmetics, etc.) above the set. (including on shelves above, etc.) WARNING : 1) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualied service personnel. 2) Do not remove the grounding pin on the power plug. This apparatus is equipped with a three pin grounding-type power plug. This plug will only t a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the grounding plug. TH-60PF50U is ENERGY STAR® compliant. As an ENERGY STAR® Partner, Panasonic has determined that this product meets the ENERGY STAR® guidelines for energy efciency. 2 Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments / accessories specied by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15) To prevent electric shock, ensure the grounding pin on the AC cord power plug is securely connected. 3 FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced technician for help. This device complies with Part15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION: To assure continued compliance, follow the attached installation instructions and use only shielded interface cables when connecting to computer or peripheral devices. Any changes or modications not expressly approved by Panasonic Corp. of North America could void the user's authority to operate this device. FCC Declaration of Conformity Model No. TH-60PF50U, TH-65PF50U Responsible Party: Contact Source: Panasonic Corporation of North America Three Panasonic Way 2F-5, Secaucus, NJ 07094 Panasonic System Communications Company of North America 1-800-973-4390 CANADIAN NOTICE: This Class B digital apparatus complies with Canadian ICES-003. Note: Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention to remain on the Plasma Display. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode. Trademark Credits • VGA is a trademark of International Business Machines Corporation. • Macintosh is a registered trademark of Apple Inc., USA. • SVGA, XGA, SXGA and UXGA are registered trademarks of the Video Electronics Standard Association. Even if no special notation has been made of company or product trademarks, these trademarks have been fully respected. • HDMI, the HDMI Logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. • “RealD 3D” is a trademark of RealD. 4 Safety Precautions CAUTION This Plasma Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury. (All of the following accessories are manufactured by Panasonic Corporation.) • Speakers .................................................... TY-SP58P10WK (for TH-60PF50U), TY-SP65P11WK (for TH-65PF50U) • Pedestal ..................................................... TY-ST58P20 (for TH-60PF50U), TY-ST65P20 (for TH-65PF50U) • Mobile stand ............................................... TY-ST58PF20 (for TH-60PF50U) • Mobile Stand for Display ............................ TY-ST65PF1 (for TH-65PF50U) • Wall-hanging bracket (angled) ................... TY-WK65PR20 • BNC Dual Video Terminal Board ................ TY-FB9BD • HD-SDI Terminal Board ............................. TY-FB9HD • HD-SDI Terminal Board with audio ............ TY-FB10HD • Dual Link HD-SDI Terminal Board.............. TY-FB11DHD • Dual HDMI Terminal Board ........................ TY-FB10HMD • DVI-D Terminal Board ................................ TY-FB11DD • Mate-IF Boad ............................................. TY-FB11HB • AV Terminal Box ......................................... TY-TB10AV • 3D IR TRANSMITTER ............................... TY-3D30TRW • Touch Panel ............................................... TY-TP60P30K (for TH-60PF50U), TY-TP65P30K (for TH-65PF50U) • 3D Eyewear ............................................... TY-EW3D3SU, TY-EW3D3MU, TY-EW3D3LU • Wireless Module ........................................ ET-WM200U Always be sure to ask a qualied technician to carry out set-up. Small parts can present choking hazard if accidentally swallowed. Keep small parts away from young children. Discard unneeded small parts and other objects, including packaging materials and plastic bags/sheets to prevent them from being played with by young children, creating the potential risk of suffocation. When using the Plasma Display Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display. • Top of the Plasma Display is usually very hot due to the high temperature of exhaust air being released through the ventilation holes. Burns or personal injuries can happen if any body parts are brought too close. Placing any object near the top of the display could also result in heat damages to the object as well as to the Display if its ventilation holes are blocked. Be sure to disconnect all cables before moving the Plasma Display. • Moving the Display with its cables attached might damage the cables which, in turn, can cause re or electric shock. Disconnect the power plug from the wall outlet as a safety precaution before carrying out any cleaning. • Electric shocks can result if this is not done. Clean the power cable regularly to prevent it from becoming dusty. • Built-up dust on the power cord plug can increase humidity which might damage the insulation and cause re. Unplug the cord from the wall outlet and clean it with a dry cloth. This Plasma Display radiates infrared rays, therefore it may affect other infrared communication equipment. Install your infrared sensor in a place away from direct or reected light from your Plasma Display. Note: Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention to remain on the Plasma Display. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode. 5 Safety Precautions WARNING Setup Do not place the Plasma Display on sloped or unstable surfaces, and ensure that the Plasma Display does not hang over the edge of the base. • The Plasma Display may fall off or tip over. Do not place any objects on top of the Plasma Display. • If water spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in re or electric shock. If any foreign objects get inside the Plasma Display, please consult an Authorized Service Center. Do not cover the ventilation holes. • Doing so may cause the Plasma Display to overheat, which can cause re or damage to the Plasma Display. Transport only in upright position! • Transporting the unit with its display panel facing upright or downward may cause damage to the internal circuitry. If using the pedestal (optional accessory), leave a space of 3 15/16” (10 cm) or more at the top, left and right, and 2 3/4” (7 cm) or more at the rear, and also keep the space between the bottom of the display and the oor surface. If using some other setting-up method, follow the manual of it. (If there is no specic indication of installation dimension in the installation manual, leave a space of 3 15/16” (10 cm) or more at the top, bottom, left and right, and 2 3/4” (7 cm) or more at the rear.) When installing the Plasma Display vertically; Turn up the power switch for the upward direction when you install the Plasma Display vertically. And set “DISPLAY ORIENTATION” to “PORTRAIT” in SETUP menu. An apparatus with CLASS I construction shall be connected to a mains socket outlet with a protective earthing connection. AC Power Supply Cord The Plasma Display is designed to operate on 110 - 127 V AC, 50/60 Hz. Ensure that the mains plug is easily accessible. Do not use any power supply cord other than that provided with this unit. • Doing so may cause re or electric shocks. Securely insert the power cord plug as far as it will go. • If the plug is not fully inserted, heat may be generated which could cause re. If the plug is damaged or the wall socket plate is loose, they should not be used. Do not handle the power cord plug with wet hands. • Doing so may cause electric shocks. Do not do anything that might damage the power cable. When disconnecting the power cable, hold the plug, not the cable. • Do not make any modications, place heavy objects on, place near hot objects, heat, bend, twist or forcefully pull the power cable. Doing so may cause damage to the power cable which can cause re or electric shock. If damage to the cable is suspected, have it repaired at an Authorized Service Center. If the Plasma Display will not be used for a long period of time, unplug the power cord from the wall outlet. If problems occur during use If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor is detected from the Plasma Display, unplug the power cord immediately. • Continuous use of the Display under these conditions might cause re or permanent damage to the unit. Have the Display evaluated at an Authorized Service Center. Services to the Display by any unauthorized personnel are strongly discouraged due to its high voltage dangerous nature. If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet becomes damaged, disconnect the power cord plug immediately. • A short may occur, which could cause re. Contact an Authorized Service Center for any repairs that need to be made. Maintenance The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-free cloth. • If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surface is dry. • Do not scratch or hit the surface of the panel with ngernails or other hard objects, otherwise the surface may become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected. If the cabinet becomes dirty, wipe it with a soft, dry cloth. • If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth. • Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get inside the unit, operating problems may result. • Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC. 6 Safety Precautions 3D Safety Precautions WARNING Small Parts 3D Eyewear contains small parts (battery and specialized band, etc.) and must be kept out of reach of small children to avoid accidental ingestion. Disassembly Do not disassemble or modify the 3D Eyewear. CAUTION To enjoy 3D images safely and comfortably, please read these instructions fully. Use for commercial applications and public viewing Someone in authority should responsibly convey the precautions for use of the 3D Eyewear to the user. 3D Eyewear (sold separately) Do not drop, exert pressure on, or step on the 3D Eyewear. Be careful of the tips of the frame when putting on the 3D Eyewear. Be careful not to trap a nger in the hinge section of the 3D Eyewear. Pay special attention when children are using the 3D Eyewear. 3D Eyewear should not be used by children younger than 5 - 6 years old, as a guideline. All children must be fully supervised by parents or guardians who must ensure their safety and health throughout the using 3D Eyewear. 7 Safety Precautions Viewing 3D Content Content for 3D viewing includes commercially available Blu-ray discs, 3D broadcasts, etc. When preparing your own 3D content, ensure that it is properly produced. Do not use the 3D Eyewear if you have a history of over-sensitivity to light, heart problems, or have any other existing medical conditions. Please stop using the 3D Eyewear immediately, if you feel tired, are not feeling well or experience any other uncomfortable sensation. Take an appropriate break after viewing a 3D movie. Take a break of between 30 - 60 minutes after viewing 3D content on interactive devices such as 3D games or computers. Be careful not to strike the screen or other people unintentionally. When using the 3D Eyewear the distance between the user and screen can be misjudged. The 3D Eyewear must only be worn when viewing 3D content. If you do not look toward the screen for a while when viewing 3D images, the 3D Eyewear may be turned off automatically. If you suffer from any eyesight problems (short / far-sighted, astigmatism, eyesight differences in left and right), please ensure to correct your vision before using the 3D Eyewear. Stop using the 3D Eyewear if you can clearly see double images when viewing 3D content. Do not use the 3D Eyewear at a distance less than the recommended distance. View from at least the recommended distance (3 times the effective height of the screen). Recommended distance TH-60PF50U: 86.7”/2.2 m TH-65PF50U: 94.5”/2.4 m When the top and bottom area of the screen is blackened, such as movies, view the screen at a distance 3 times further than the height of the actual image. (That makes the distance closer than above recommended gure.) 3D Eyewear (sold separately) Use Before using the 3D Eyewear, ensure no breakable objects surrounding the user to avoid any accidental damage or injury. Remove the 3D Eyewear before moving around to avoid falling or accidental injury. Use the 3D Eyewear only for the intended purpose and nothing else. Do not use 3D Eyewear in the condition of high temperature. Do not use if the 3D Eyewear is physically damaged. Do not use any devices that emit the infrared signals near the 3D Eyewear, as this may cause the 3D Eyewear false operations. Do not use devices (such as mobile phones or personal transceivers) that emit strong electromagnetic waves near the 3D Eyewear as this may cause the 3D Eyewear to malfunction. Stop using the 3D Eyewear immediately if a malfunction or fault occurs. Stop using the 3D Eyewear immediately if you experience any redness, pain, or skin irritation around the nose or temples. In rare cases, the materials used in the 3D Eyewear may cause an allergic reaction. 8 Accessories Accessories Supplied Check that you have the Accessories and items shown Operating Instruction book Remote Control Transmitter N2QAYB000691 CD-ROM × 1 • Operating Instructions Display Operations Network Operations • Software license statements GNU GENERAL PUBLIC LICENSE GNU LESSER GENERAL PUBLIC LICENSE Clamper × 1 TMME289 Batteries for the Remote Control Transmitter (AA Size × 2) Ferrite core × 2 J0KG00000014 AC cord Use the Ferrite cores to comply with the EMC standard. (see page 12) Remote Control Batteries Requires two AA batteries. 1. Pull and hold the hook, then open the battery cover. 2. Insert batteries - note correct polarity (+ and -). 3. Replace the cover. “AA” size + + - Helpful Hint: For frequent remote control users, replace old batteries with Alkaline batteries for longer life. Precaution on battery use Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Disposal of batteries should be in an environment-friendly manner. Observe the following precautions: 1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set. 2. Do not combine a used battery with a new one. 3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”). 4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. 5. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display. 6. Do not burn or breakup batteries. 7. Batteries must not be exposed to excessive heat such as sunshine, re or the like. 9 Connections Speaker connection When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation. Speakers (Optional accessories) 2 1 Red Red Black Black While pressing the lever, insert the core wire. Return the lever. AC cord connection and xing, cable xing AC cord xing Unplug the AC cord Plug the AC cord into the display unit. Plug the AC cord until it clicks. Note: Make sure that the AC cord is locked on both the left and right sides. Using the clamper Secure any excess cables with clamper as required. Unplug the AC cord pressing the two knobs. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet rst. Note: One clamper is supplied with this unit. In case of securing cables at three positions, please purchase it separately. TH-60PF50U TH-65PF50U 1 Attach the clamper To remove from the unit: 2 Bundle the cables To loosen: hole snaps Insert the clamper in a hole. 10 Keep pushing both side snaps hooks Set the tip in the hooks knob Keep pushing the knob Connections Video equipment connection Ex. TH-65PF50U Terminals are on the bottom side of the Plasma Display. SERIAL: Control the Plasma Display by connecting to PC. 3D IR TRANSMITTER: Connect the 3D IR TRANSMITTER (optional accessory). (8Ω,20W[10W+10W]) SLOT: Terminal board (optional accessories) insert slot (see page 5) Note: The right side slot is for terminal board with 2-slot width. The terminal board with 1-slot width does not function when installed in the right side slot. AV IN (VIDEO): Composite Video Input Terminal COMPONENT/RGB IN: Component/RGB Video Input Terminal DVI-D IN: DVI-D Input Terminal PC IN: PC Input Terminal Connect to video terminal of PC or equipment with Y, PB(CB) and PR(CR) output. AV IN (HDMI): HDMI Input Terminal Connect to video equipment such as VCR or DVD player. WIRELESS MODULE, LAN: Refer to “Operating Instructions, Network Operations”. 11 Connections Example of Network Connection (Wired LAN) COMPUTER Display (main unit, rear) Less than 3.9 inch (10 cm) LAN cable (not supplied) Ferrite core (supplied) Installing the Ferrite core Ferrite core (supplied) Less than 3.9 inch (10 cm) Open Pull back the tabs (in two places) Wind the cable twice Press the cable through and close Hub or broadband router Notes: • Make sure the broadband router or hub supports 10BASE-T/100BASE-TX. • To connect a device using 100BASE-TX, use “category 5” LAN cable. • Touching the LAN terminal with a statically charged hand (body) may cause damage due to its discharge. Do not touch the LAN terminal or a metal part of the LAN cable. • For instructions on how to connect, consult your network administrator. Connecting Wireless Module (Wireless LAN) To use the wireless function, the wireless module (ET-WM200U) (sold separately) is necessary. When connecting the wireless module to the display, remove the protective lm and cap. (8Ω,20W[10W+10W]) Connecting procedure Hold the wireless module with its LED on the near side and connect it to the wireless module connection terminal. Note: Do not connect any other device than the wireless module (ET-WM200U). ET-WM200 LED 12 Power ON / OFF Connecting the AC cord plug to the Plasma Display. Connecting the plug to the Wall Outlet. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet rst. INPUT MENU -/ VOL +/ ENTER/ Press the Power switch on the Plasma Display to turn the set on: Power-On. Power Indicator Power Indicator: Green Remote Control Sensor [Starting up the network] It takes some time for the network to start up just after the power is turned on. During that time, “NETWORK SETUP” in the “SETUP” menu is grayed out and cannot be set. Press the button on the remote control to turn the Plasma Display off. Power Indicator: Red (standby) Press the button on the remote control to turn the Plasma Display on. Power Indicator: Green Turn the power to the Plasma Display off by pressing the when the Plasma Display is on or in standby mode. switch on the unit, Note: During operation of the power management function, the power indicator turns orange in the power off state. 13 Power ON / OFF When rst switching on the unit Following screen will be displayed when the unit is turned on for the rst time. Select the items with the remote control. Unit buttons are invalid. OSD LANGUAGE VIEWING ENVIRONMENT OSD LANGUAGE VIEWING ENVIRONMENT English (UK) DAY/TIME SETUP DAY/TIME SETUP TIME PUBLIC SPACE Deutsch Italiano Español 1 Select viewing mode. 2 Set. SET Select the language. 2 Set. 1 MON 99:99 DAY TIME ENGLISH (US) SELECT MON 99:99 SET HOME Français PUBLIC SPACE: Suitable for commercial applications. HOME: Suitable for home environment. 1 Select “DAY” or “TIME”. 2 Setup “DAY” or “TIME”. 1 Select “SET”. 2 Set. DISPLAY ORIENTATION DISPLAY ORIENTATION LANDSCAPE PORTRAIT For vertical installation, select “PORTRAIT”. 2 Set. 1 Notes: • Once the items are set, the screens won't be displayed when switching on the unit next time. • After the setting, the items can be changed in the following menus. OSD LANGUAGE DAY/TIME SETUP DISPLAY ORIENTATION Power ON warning message The following message may be displayed when turning the unit power ON: 3D Safety Precautions When 3D images will be viewed by unspecied number of people or used for commercial applications, someone in authority should convey the following precautions. These precautions should be followed in the home as well. To enjoy 3D images safely and comfortably, please refer to the Operating Instructions for in-depth description. Please refrain from viewing 3D images if you do not feel well or are experiencing visual fatigue. Activate 3D Safety Precautions if you deliver 3D images to unspecied audiences for business or other purposes. If “3D FUNCTION” in “3D SETTINGS” is set to “ON”, a warning message is displayed every time the power is turned ON. No activity power off Precautions ’NO ACTIVITY POWER OFF’ IS ENABLED. If “NO ACTIVITY POWER OFF” in SETUP menu is set to “ENABLE”, a warning message is displayed every time the power is turned ON. These message displays can be set with the following menu: Options menu 3D Safety Precautions Power On Message 14 Basic Controls Main Unit Brightness Sensor Detects the brightness in the viewing environment Remote control sensor Volume Adjustment Volume Up “+” Down “–” When the menu screen is displayed: “+” : press to move the cursor up “–” : press to move the cursor down Enter / Aspect button INPUT Main Power On / Off Switch MENU -/ VOL +/ ENTER/ MENU Screen ON / OFF Each time the MENU button is pressed, the menu screen will switch. Power Indicator The Power Indicator will light. Normal Viewing PICTURE SETUP • Power-OFF .... Indicator not illuminated (The unit will SOUND POS./SIZE still consume some power as long as the power cord is still inserted into the wall outlet.) INPUT button (Input signal selection) • Standby ........ Red Orange (When “Slot power” is set to “On”.) Orange (Depending on the type of the function board installed, when the power is supplied to the slot) Orange (When “CONTROL I/F SELECT” is set to “LAN” or “WEB CONTROL” is set to “ON”. Refer to “Operating Instructions, Network Operations”.) • Power-ON ...... Green • PC POWER MANAGEMENT (DPMS) ........................ Orange (With PC input signal.) When this function is set to ON, it operates under the following conditions to turn the power on or off automatically. When no pictures (HD/VD sync signals) are detected for 30 or so seconds during PC signal input: Power is turned off (standby); the power indicator lights up orange. When pictures (HD/VD sync signals) are subsequently detected: Power is turned on; the power indicator lights up green. • DVI-D POWER MANAGEMENT ........................Orange (With DVI input signal.) • NO SIGNAL POWER OFF ........................Red Equipment power supply is turned OFF when there is no signal. When this is set to “ENABLE”, the power supply of the unit goes Off 10 minutes after the input signals stop. 15 Basic Controls Remote Control Transmitter ACTION button Press to make selections. ASPECT button Press to adjust the aspect. Standby (ON / OFF) button The Plasma Display must rst be plugged into the wall outlet and turned on at the power switch (see page 13). Press this button to turn the Plasma Display On, from Standby mode. Press it again to turn the Plasma Display Off to Standby mode. POS. /SIZE button OFF TIMER button The Plasma Display can be preset to switch to standby after a xed period. The setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed. 30 MIN 60 MIN 90 MIN 0 MIN(Cancel) When three minutes remain, “OFF TIMER 3 MIN” will ash. The off timer is cancelled if a power interruption occurs. AUTO SETUP button Automatically adjusts the position/ size of the screen. SETUP button PICTURE button Sound mute On / Off Press this button to mute the sound. Press again to reactivate sound. Sound is also reactivated when power is turned off or volume level is changed. N button POSITION buttons INPUT button Press to select input signal sequentially. ECO MODE (ECO) Press to change the ECO MODE setup status. FUNCTION buttons (FUNCTION) SOUND button Volume Adjustment Press the Volume Up “+” or Down “–” button to increase or decrease the sound volume level. R button Press the R button to return to previous menu screen. RECALL button Press the “RECALL” button to display the current system status. 1 Input label 2 Aspect mode During 3D images Audio input Prole name NANODRIFT SAVER operating 3 Off timer The off timer indicator is displayed only when the off timer has been set. 4 Clock display PC 1 4:3 3D COMPONENT 2 MEMORY NAME: MEMORY2 NANODRIFT 4 10: 00 OFF TIMER 90MIN Digital Zoom 16 3 Specications TH-60PF50U Power Source Power Consumption Rated Power Consumption Stand-by condition Power off condition Plasma Display panel Screen size (No.of pixels) Operating condition Temperature Humidity Applicable signals Color System Scanning format PC signals Connection terminals VIDEO AV IN AUDIO L-R HDMI COMPONENT/RGB IN Y/G PB/CB/B PR/CR/R AUDIO L-R DVI-D IN AUDIO PC IN TH-65PF50U 110 - 127 V AC, 50/60 Hz 515 W 555 W 0.4 W 0.4 W 0.2 W 0.2 W Drive method : AC type 60-inch, Drive method : AC type 65-inch, 16:9 aspect ratio 16:9 aspect ratio 52.3” (1,330 mm) (W) × 29.4” (748 mm) (H) 56.4” (1,434 mm) (W) × 31.7” (806 mm) (H) × 60.1” (1,526 mm) (diagonal) × 64.7” (1,645 mm) (diagonal) 2,073,600 (1,920 (W) × 1,080 (H)) [5,760 × 1,080 dots] 32 °F - 104 °F (0 °C - 40 °C) 20 % - 80 % NTSC, PAL, PAL60, SECAM, Modied NTSC 525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 750 (720) / 60p · 50p, 1125 (1080) / 60i · 60p · 50i · 50p · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i VGA, SVGA, XGA, SXGA UXGA ···· (compressed) Horizontal scanning frequency 15 - 110 kHz Vertical scanning frequency 48 - 120 Hz BNC RCA Pin jack × 2 1.0 Vp-p (75 ) 0.5 Vrms, Shared with COMPONENT/RGB IN TYPE A Connector BNC BNC BNC RCA Pin jack × 2 DVI-D 24 Pin Content Protection Stereo mini jack (M3) × 1 High-Density Mini D-sub 15 Pin Stereo mini jack (M3) × 1 External Control Terminal D-sub 9 Pin 3D IR TRANSMITTER for 3D IR TRANSMITTER (TY-3D30TRW) 3D SHUTTER OUT M3 jack × 1 DC 8V OUT Center plus, for EIAJ 4mm plug AUDIO SERIAL WIRELESS MODULE LAN with sync 1.0 Vp-p (75 ) 0.7 Vp-p (75 ) 0.7 Vp-p (75 ) 0.5 Vrms, Shared with VIDEO Compliance with DVI Revision 1.0 Compatible with HDCP 1.1 0.5 Vrms, Shared with PC IN Y or G with sync 1.0 Vp-p (75 ) Y or G without sync 0.7 Vp-p (75 ) PB/CB/B: 0.7 Vp-p (75 ) PR/CR/R: 0.7 Vp-p (75 ) HD/VD: 1.0 - 5.0 Vp-p (high impedance) 0.5 Vrms, Shared with DVI-D IN RS-232C compatible for Wireless module (ET-WM200U) RJ45 10BASE-T/100BASE-TX, compatible with PJLink™ 6 , 16 W [8 W + 8 W] (10 % THD) 8 , 20 W [10 W + 10 W] (10 % THD) Dimensions (W × H × D) 56.5” (1,434 mm) × 33.6” (852 mm) × 3.9” (99 mm) 61.2” (1,554 mm) × 36.5” (925 mm) × 3.9” (99 mm) Mass (weight) main unit only with speakers approx. 108.1 lbs approx. 121.3 lbs approx. 132.3 lbs approx. 145.5 lbs EXT SP Note: Design and specications are subject to change without notice. Mass and dimensions shown are approximate. 17 (for the U.S.A and Puerto Rico) Panasonic System Communications Company of North America Unit of Panasonic Corporation of North America Three Panasonic Way 2F-5 Secaucus, NJ 07094 Panasonic Professional Flat Panel Display Limited Warranty Panasonic System Communications Company of North America (referred to as “the Warrantor”) will repair this product and all included accessories with new or refurbished parts, free of charge in the USA or Puerto Rico, of the original purchase in the event of a defect in materials or workmanship as follows: Models or Parts Part Warranty Professional Flat Panel Display 2 Years Labor Warranty 2 Years On-site or carry-in service in the USA and Puerto Rico may be obtained during the warranty period by contacting Panasonic System Communications Company of North America Service toll free at 1-800-973-4390. This warranty is extended only to the original purchaser and is non transferable. A purchase receipt or other proof of date of original purchase will be required before warranty service is rendered. This warranty only covers failures due to defects in materials or workmanship, which occur during normal use. The warranty does not cover damage which occur in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from improper installation, set-up adjustments, improper antenna, inadequate signal pickup, maladjustment of consumer controls, improper operation, power line surge, improper voltage supply, lighting damage, or service by anyone other than an authorized repair facility, or damage that is attributable to acts of God. LIMITS AND EXCLUSIONS There are no express warranties except as listed above. THE WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT LIMITION, DAMAGE TO DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THE WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may nor apply to you. This warranty gives you specific legal rights and you may other rights, which vary from state to state. If you have a problem with this product that is not handled to your satisfaction, then write the Consumer Affairs Department at the Company address indicated above. In the USA and Puerto Rico FOR SERVICE CALL TOLL FREE 1-800-973-4390 18 (for Canada) Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 LIMITED WARRANTY STATEMENT Panasonic Canada Inc. (also known as PCI) warrants this product to be free of defects in material and workmanship under normal use during the applicable warranty coverage period described below. PCI agrees to repair, or at its option, exchange, any part that becomes defective. However, the product must be purchased and serviced in Canada. The product or part that shows evidence of defect must be delivered prepaid or carried in to an authorized Panasonic Broadcast Service Center. This warranty does not cover shipping costs. The warranty coverage period is one year for both parts and labour beginning with the date of original end user purchase, subject to the exceptions as stated below. Repaired or replacement parts supplied during the warranty coverage period carry the unexpired portion of the original warranty coverage period. Proof of product purchase is a condition of warranty service. The owner must produce the product purchase receipt or other satisfactory evidence of date of original purchase. This warranty does not apply to external appearance items, such as handles, knobs, safety windows, etc. This warranty does not apply to any part, or parts, of the product, installed, altered, repaired or misused in any way that, in the opinion of PCI, affects the reliability of or detracts from the performance of the product. For products requiring routine preventive maintenance, that maintenance must be performed in order to maintain warranty coverage. Serial numbers that have been altered, defaced or removed void this warranty. This warranty does not cover replacements or repairs necessitated by loss or damage resulting from any cause beyond the control of PCI. Marking or retained images (sometimes called “burn-in”) resulting from the display of fixed images on video display products are not defects and are not covered under this warranty. THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES. In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions may not be applicable. WARRANTY COVERAGE PERIOD EXCEPTIONS Item Video Tape P2/SD Cards Video Heads D5 Video heads Parts Labour 30 days—Replacement only (content not covered) (Content not covered) N/A 1 year or 2,000 hrs. (prorated) Whichever comes first 1 year or 1,000 hrs. Whichever comes first 90 days 2 years N/A 1 year or 2,000 hrs. Whichever comes first 1 year or 1,000 hrs. Whichever comes first 90 days 2 years Maintenance Items Colour Camera CCD Imaging Block BT-H Series LCD Monitors 2 years * DLP™ Projectors 3 years or 17,000 hrs. Whichever comes first * LCD Projectors above 3 years or 2,500 hrs. Whichever comes first 2,500 ANSI Lumens * LCD Projectors below 3 years or 1,500 hrs. Whichever comes first 2,500 ANSI Lumens Projector Lamps 50% of the rated lamp life or 1 year. Whichever comes first 2 years 3 years or 17,000 hrs. Whichever comes first 3 years or 2,500 hrs. Whichever comes first. 3 years or 1,500 hrs. Whichever comes first 50% of the rated lamp life or 1 year. Whichever comes first. All Plasma displays 103 inch Plasma displays Hard Drive Disk Unit 2 years 3 years 1 year 2 years (burn-in not covered) 3 years (burn-in not covered) 1 year plus balance (if any) of the original Manufacturer’s Limited Warranty. (Content not covered) • Dust, smoke, rental/staging environment and twenty-four/seven operation, dramatically decreases the interval between performances of routine preventive maintenance required to maintain this warranty coverage. Warranty Service If the product needs to be shipped for service, carefully pack (preferably in the original carton) and enclose a letter, detailing the complaint. Send prepaid and adequately insured to the local authorized Panasonic Service Centre in your area or to Panasonic Technical Support and Product Services Department, 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3. Shipping to the latter location requires a return authorization before shipment. No liability is assumed for loss or damage to the product while in transit. 19 20 USA Only: Disposal may be regulated in your community due to environmental considerations. For disposal or recycling information, please visit Panasonic website: http://www.panasonic.com/environmental or call 1-888-769-0149. Customer’s Record The model number and serial number of this product can be found on its back cover. You should note this serial number in the space provided below and retain this book, plus your purchase receipt, as a permanent record of your purchase to aid in identication in the event of theft or loss, and for Warranty Service purposes. Model Number Serial Number ¤ Panasonic Corporation 2012 Panasonic System Communications Company of North America Unit of Panasonic Corporation of North America Executive Ofce : Three Panasonic Way 2F-5, Secaucus, NJ 07094 Panasonic Canada Inc. 5770 Ambler Drive Mississauga, Ontario L4W 2T3 Printed in U.S.A.