Description Remote Control System Additional AM

KEELO REMOTE CONTROL SYSTEMS 12Vdc,
•
•
•
•
•
•
•
•
•
•
•
•
Complete Remote Control System
1 – 3 Channels
12Vdc Supply
High Security
Protocol
‘Easy Learn’ Feature
Easy Installation Via Screw Terminals.
Up to 7 Transmitters per System
Relay Outputs 5A @ 230Vac
Momentary or Latching Outputs
Robust Enclosure
Requires No Radio Licence
Range up to 60 Metres
Description
A versatile general purpose remote control, which can be used for controlling many different applications.
The system utilises the highly secure Keeloq code hopping protocol to ensure reliable operation.
Easy to install, the receiver is connected using standard ‘screw terminals’ provided. Power to the receiver is
12Vdc and the output(s) can switch up to 5A at 230Vac.
The receiver outputs operate when the transmitter switch is pressed. The outputs can be set to ‘momentary’ or
‘latching’ operation.
The system is supplied ready to ‘plug and play’, in addition a further 6 transmitters can be ‘learnt’ by the
receiver.
Remote Control System
AM System 1 Channel
Freq
(MHz)
433.92
Range**
(Metres)
60
QS2
AM System 2 Channel
433.92
60
QS3
AM System 3 Channel
433.92
60
Part Number
Description
QS1
Additional AM Transmitter Keyfobs
Part Number
Description
QTX1
Transmitter Keyfob 1 switch
QTX2
Transmitter Keyfob 2 switch
QTX3
Transmitter Keyfob 3 switch
** Range stated is optimum, direct line of sight. In worst conditions this can be reduced.
DSQS-1
March 07
©2007
Page 1
KEELO REMOTE CONTROL SYSTEMS 12Vdc,
Data Outputs
Each output relay provides an isolated switch. Connections are Common (COM), Normally Open (NO) and
Normally Closed (NC).
NC
COM
NO
NC
COM
NO
Relay Connections when
Transmitter NOT Operating
Relay Connections when
Transmitter OPERATING
The action of the Switch outputs is set by the Option link setting (three pins protruding from the PCB marked
Option). A link is made / removed by the small shorting link ‘cap’ placed over the pin header.
1-2 Connected: Momentary - The output is activated for duration of the transmitter operation, up to 26 Seconds.
2-3 Connected: Latching - The output toggles on each successive transmitter press.
Please Note: The relay contacts in this unit are for functional use only and must not be used for isolation
purposes
Learning a New Transmitter Keyfob Switch
1. Short the two ‘learn’ pins on the receiver PCB, the receiver relays will click continuously.
2. Press the transmitter once, the receiver relays will stop
3. Press the transmitter again, the receiver relays will ‘buzz’ briefly. This transmitter will now operate the system.
Erasing Existing Transmitters
1. Short the two learn pins on the receiver for 10 seconds.
2. The receiver relays will ‘buzz’ briefly after the 10 seconds to indicate the Tx encoder(s) have been erased
NOTE: You can not erase individual Tx encoders
Technical Specifications
Transmitter Keyfob
Battery Type
GP23AE (supplied)
Electrical Characteristics
Min
Typical
Max
Supply Voltage
Supply Current : Quiescent
Supply Current : Transmitting
Operating frequency
8.5
9
0
8
433.92
16
MIN
11
TYPICAL
12.0
14
140
MAX
13
Receiver Decoder
Dimensions
96mm x 55mm x 29mm
ELECTRICAL CHARACTERISTICS
Supply Voltage for +12 v
Supply Current:
Quiescent
All relays operating
sales@quasaruk.co.uk
DSQS-1
March 07
©2007
www.quasaruk.co.uk
Page 2
Units
V
mA
mA
MHz
DIMENSION
V
mA
mA
Download PDF