English - Panasonic Canada

Safety Information
■ Read the operating instructions for the unit and all other components of your car audio system carefully before using the
system. They contain instructions about how to use the system in a safe and effective manner. Panasonic assumes no
responsibility for any problems resulting from failure to
observe the instructions given in this manual.
This pictograph intends to alert you to the presence of important operating instructions and
Warning installation instructions. Failure to heed the
instructions may result in severe injury or death.
Warning
Observe the following warnings when using
this unit.
❑ The driver should neither watch the display nor
operate the system while driving.
Watching the display or operating the system will distract
the driver from looking ahead of the vehicle and can cause
accidents. Always stop the vehicle in a safe location and use
the parking brake before watching the display or operating
the system.
❑ Use the proper power supply.
This product is designed for operation with a negative
grounded 12 V DC battery system. Never operate this product with other battery systems, especially a 24 V DC battery
system.
❑ Keep batteries and insulation film out of reach of
infants.
Batteries and insulation film can be ingested, so keep them
out of the reach of infants. If an infant ingests a battery or
insulation film, please seek immediate medical attention.
❑ Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
❑ Do not disassemble or modify the unit.
Do not disassemble, modify the unit or attempt to repair the
product yourself. If the product needs to be repaired, consult
your dealer or an authorized Panasonic Servicenter.
❑ Do not use the unit when it is out of order.
If the unit is out of order (no power, no sound) or in an
abnormal state (has foreign objects in it, is exposed to
water, is smoking, or smells), turn it off immediately and
consult your dealer.
❑ The remote control unit should not lie about in the
car.
If the remote control unit lies about, it could fall on the floor
while driving, get wedged under the brake pedal, and lead to
a traffic accident.
❑ Refer fuse replacement to qualified service personnel.
When the fuse blows out, eliminate the cause and have it
replaced with the fuse prescribed for this unit by a qualified
service engineer. Incorrect replacement of the fuse may lead
to smoke, fire, and damage to the product.
2
■ This manual uses pictographs to show you how to use the
product safely and to alert you to potential dangers resulting
from improper connections and operations. The meanings of
the pictographs are explained below. It is important that you
fully understand the meanings of the pictographs in order to
use this manual and the system properly.
Caution
This pictograph intends to alert you to the presence of important operating instructions and
installation instructions. Failure to heed the
instructions may result in injury or material damage.
Observe the following warnings when
installing.
❑ Disconnect the lead from the negative (–) battery
terminal before installation.
Wiring and installation with the negative (–) battery terminal
connected may cause electrical shock and injury due to a
short circuit.
Some cars equipped with the electrical safety system have
specific procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE
UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY
SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND
PERSONAL INJURY OR DEATH.
❑ Never use safety-related components for installation, grounding, and other such functions.
Do not use safety-related vehicle components (fuel tank,
brake, suspension, steering wheel, pedals, airbag, etc.) for
wiring or fixing the product or its accessories.
❑ Installing the product on the air bag cover or in a
location where it interferes with airbag operation is
prohibited.
❑ Check for piping, gasoline tank, electric wiring, and
other items before installing the product.
If you need to open a hole in the vehicle chassis to attach or
wire the product, first check where the wire harness, gasoline tank, and electric wiring are located. Then open the hole
from outside if possible.
❑ Never install the product in a location where it interferes with your field of vision.
❑ Never have the power cord branched to supply other
equipment with power.
❑ After installation and wiring, you should check the
normal operation of other electrical equipment.
The continuation of their using in abnormal conditions may
cause fire, electrical shock or a traffic accident.
❑ In the case of installation to an airbag-equipping
car, confirm warnings and cautions of the vehicle
manufacturer before installation.
❑ Make sure the leads do not interfere with driving or
getting in and out of the vehicle.
❑ Insulate all exposed wires to prevent short circuiting.
CQ-C7403U/C7303U/C7203U/C7103U
❑ Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road and
traffic conditions while driving.
❑ Do not insert or allow your hand or fingers to be
caught in the unit.
To prevent injury, do not get your hand or fingers caught in
moving parts or in the disc slot. Especially watch out for
infants.
❑ This unit is designed for use exclusively in automobiles.
❑ Do not operate the unit for a prolonged period with
the engine turned off.
Operating the audio system for a long period of time with the
engine turned off will drain the battery.
❑ Do not expose the unit to direct sunlight or excessive heat.
Otherwise these will raise the interior temperature of the
unit, and it may lead to smoke, fire, or other damage to the
unit.
❑ Do not use the product where it is exposed to water,
moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead to
smoke, fire, or other damage to the unit. Make especially
sure that the unit does not get wet in car washes or on rainy
days.
Avoid slanted or strongly curved surfaces for installation. If
the installation is not stable, the unit may fall down while
driving and this can lead to an accident or injury.
❑ Installation Angle
The product should be installed in a horizontal position with
the front end up at a convenient angle, but not more than
30˚.
The user should bear in mind that in some areas there may
be restrictions on how and where this unit must be installed.
Consult your dealer for further details.
❑ Wear gloves for safety. Make sure that wiring is
completed before installation.
❑ To prevent damage to the unit, do not connect the
power connector until the whole wiring is completed.
❑ Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)
Observe the following cautions when handling
the battery for the remote control unit.
● Use only specified battery (CR2025).
● Match the polarity of the battery with the (+) and (–) marks
in the battery case.
● Replace dead battery as soon as possible.
● Remove the battery from the remote control unit when not
using it for an extended period of time.
● Insulate the battery (by placing them in a plastic bag or covering them with vinyl tape) before disposal or storage.
Observe the following cautions when
installing.
● Dispose of the battery according to the local regulations.
● Do not disassemble, recharge, heat or short the battery. Do
❑ Refer wiring and installation to qualified service
personnel.
In case of battery leakage
● Thoroughly wipe the battery liquid off the battery case and
Installation of this unit requires special skills and experience.
For maximum safety, have it installed by your dealer.
Panasonic is not liable for any problems resulting from your
own installation of the unit.
❑ Follow the instructions to install and wire the product.
Safety Information
Observe the following cautions when using this
unit.
English
❑ Do not install the product where it is exposed to
strong vibrations or is unstable.
Caution
not throw a battery into a fire or water.
insert new battery.
● If any part of your body or clothing comes into contact with
battery liquid, wash it with plenty of water.
● If battery liquid comes into contact with your eyes, wash
them with plenty of water and get immediate medical attention.
Not following the instructions to properly install and wire the
product could cause an accident or fire.
❑ Take care not to damage the leads.
When wiring, take care not to damage the leads. Prevent
them from getting caught in the vehicle chassis, screws, and
moving parts such as seat rails. Do not scratch, pull, bend or
twist the leads. Do not run them near heat sources or place
heavy objects on them. If leads must be run over sharp
metal edges, protect the leads by winding them with vinyl
tape or similar protection.
❑ Use the designated parts and tools for installation.
Use the supplied or designated parts and appropriate tools
to install the product. The use of parts other than those supplied or designated may result in internal damage to the unit.
Faulty installation may lead to an accident, a malfunction or
fire.
❑ Do not block the air vent or the cooling plate of the
unit.
Blocking these parts will cause the interior of the unit to
overheat and will result in fire or other damage.
CQ-C7403U/C7303U/C7203U/C7103U
3
Safety Information (continued)
The following applies only in the U.S.A.
Caution
THIS PRODUCT IS A CLASS I LASER PRODUCT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
Part 15 of the FCC Rules
FCC Warning:
Any unauthorized changes or modifications to this
equipment would void the user's authority to operate
this device.
Before Reading These Instructions
Differences Among 4 Models
Panasonic welcomes you to our constantly growing family of electronic products owners.
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully
selected components, and assembled by people who are proud of the reputation their work has built for our company. We
know this product will bring you many hours of enjoyment, and after you discover the quality, value and reliability we have
built into it, you too will be proud to be a member of our family.
4
This operating instruction manual is for 4 models CQ-C7403U, CQ-C7303U, CQ-C7203U and CQ-C7103U.
The difference among these models’ are mentioned below.
All screens and main body illustrations in this book represent CQ-C7403U unless otherwise specified.
Models
CQ-C7403U
CQ-C7303U
CQ-C7203U
CQ-C7103U
Subwoofer-output
5 V (60 Ω)
2.5 V (200 Ω)
5 V (60 Ω)
Preout
5 V (60 Ω)
2.5 V (200 Ω)
5 V (60 Ω)
2 V (200 Ω)
2 V (200 Ω)
Yes
Yes
No
No
Features
SRS WOW (a page 18)
Customize function (a page 31)
Yes
Yes
No
No
SQ (a page 19)
SQ7
SQ7
SQ3
SQ3
The instruction manual consists of 2 books. One is “Operating Instructions” describing the operations of the main
unit. The other is “System Upgrade Guidebook” describing the optional devices such as CD changer.
CQ-C7403U/C7303U/C7203U/C7103U
Before Reading These Instructions
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
OO-OOOOO
English
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
OO-OOOOO
Operating
Instructions
System Upgrade
Guidebook
Installation
Instructions
(YEFM285749)
(YEFM262685)
(YEFM294101)
Owners
Information Card
Instruction kit
POWER
SOURCE MENU
SEL
SRC
VOL
SET
BAND
MUTE
1
2
3
RANDOM
SCAN
REPEAT
4
5
7
8
9
0
DISP
6
TUNE
TUNE
#
NUMBER
Accessories
CAR AUDIO
Remote Control Unit
(including a battery)
(CR2025)
Power Connector
Mounting Collar
(EUR7641010)
(YGAJ021009)
(YEFX0217222)
Q'ty: 1
Q'ty: 1
Q'ty: 1
Trim Plate
CQ-C7403U/C7303U:
(YEFC05654)
CQ-C7203U/C7103U:
(YEFC051010)
Q'ty: 1
Lock Cancel Plate
Mounting Bolt
Tapping Screw
(5 mmø x 16 mm)
Hex. Nut
(5 mmø)
(YEP0FZ5701)
Q'ty: 1 set
Rear Support Strap
Removable Face
Plate Case
(YEFG04019)
(YEFA134150)
Q'ty: 1
Notes:
¡ The number in parenthesis underneath each accessory
part name is the part number for maintenance and
service.
¡ Accessories and their parts numbers are subject to
modification without prior notice due to improvements.
¡ Mounting Collar and Trim Plate are mounted on the
main unit at shipment.
Safety Information, Before Reading These Instructions
Q'ty: 1 set
Q'ty: 1
CQ-C7403U/C7303U/C7203U/C7103U
5
Before Reading These Instructions
U.S.A.
Obtain Product Information and Operating Assistance;
locate your nearest Dealer or Servicenter; purchase
Parts and Accessories; or make Customer Service and
Literature requests by visiting our Web Site at:
http://www.panasonic.com/support
or, contact us via the web at:
http://www.panasonic.com/contactinfo
You may also contact us directly at:
1-800-211-PANA (7262),
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7
pm, EST.
For hearing or speech impaired TTY users, TTY : 1-877833-8855
Customer Services Directory
Accessory Purchases:
6
Purchase Parts, Accessories and Instruction Books
online for all Panasonic Products by visiting our Web
Site at:
http://www.pasc.panasonic.com
or, send your request by E-mail to:
npcparts@panasonic.com
You may also contact us directly at:
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only)
(Monday-Friday 9 am to 8 pm, EST.)
Panasonic Services Company
20421 84th Avenue South, Kent, WA 98032
(We accept Visa, MasterCard, Discover Card, American
Express, and Personal Checks)
For hearing or speech impaired TTY users, TTY : 1-866605-1277
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc.
Panasonic Sales Company
Factory Servicenter:
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial
Park,
Carolina, Puerto Rico 00985
Phone (787) 750-4300, Fax (787) 768-2910
CQ-C7403U/C7303U/C7203U/C7103U
CANADA
WARRANTY SERVICE
FOR PRODUCT OPERATION ASSISTANCE, please contact:
Our Customer Care Centre:
Telephone #:
1-800 #:
Fax #:
Email link:
(905) 624-5505
1-800-561-5505
(905) 238-2360
“Contact Us” on
www.panasonic.ca
FOR PRODUCT REPAIRS, please locate your nearest
Authorized Servicentre at www.panasonic.ca:
Link : “ServicentresTM locator” under “Customer support”
Panasonic Factory Service:
Vancouver
Panasonic Canada Inc.
12111 Riverside Way
Richmond, BC V6W
1K8
Tel: (604) 278-4211
Fax: (604) 278-5627
Toronto
Panasonic Canada Inc.
5770 Ambler Drive
Mississauga, ON L4W 2T3
Tel: (905) 624-8447
Fax: (905) 238-2418
IF YOU SHIP THE PRODUCT TO A SERVICENTRE
Carefully pack and send prepaid, adequately insured and
preferably in the original carton.
Include details of the defect claimed, and proof of date
of original purchase.
PANASONIC SALES COMPANY,
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC.
Ave. 65 de infanteria, Km. 9.5, San Gabriel Industrial Park
Carolina, Puerto Rico 00985
This warranty gives you specific legal rights and you may also have
other rights which vary from state to state. If a problem with this
product develops during or after the warranty period, you may contact your dealer or Servicenter. If the problem is not handled to your
satisfaction, then write to warrantor’s Consumer Affairs Department
at the addresses of the warrantor.
PANASONIC AUTO PRODUCTS
LIMITED WARRANTY
LIMITED WARRANTY COVERAGE
If your product does not work properly because of defects in materials and workmanship.
Panasonic Consumer Electronics Company or Panasonic Sales
Company (collectively referred to as “the warrantor”) will, for the
length of the period indicated in the chart below, which starts with
the date of original purchase (“warranty period”), at its option either
(a) repair your product with new or refurbished parts, or (b) replace
it with a new or refurbished product. The decision to repair or
replace will be made by the warrantor.
Limited Warranty
Categories
Parts
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts, so the exclusions may not apply to you.
Labor
Audio Components (except items listed
below)
MXE Series Audio Components (except
items listed below)
Speakers
One (1) Year
One (1) Year
Two (2) Years
Two (2) Years
One (1) Year
Not Applicable
Accessories (in exchange for defective
items)
Ninety (90) Days Not Applicable
PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED
WARRANTY ARE YOUR RESPONSIBILITY.
Customer’s Record
Model
No.
Serial
No.
Dealer’s
No.
Code
No.
Dealer’s
Address
Date of
Purchase
CANADA
During the “Labor” warranty period, there will be no charge for
labor. During the “Parts” warranty period, there will be no charge for
parts. You must carry in or mail in your product during the warranty
period. If non-rechargeable batteries are included, they are not warranted. This warranty only applies to products purchased and serviced in the United States or Puerto Rico. This warranty is extended
only to the original purchaser of a new product which was not sold
“as is”. A purchase receipt or other proof of the original purchase
date is required for warranty service.
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga Ontario L4W 2T3
CARRY-IN OR MAIL-IN SERVICE
For Carry-In or Mail-In Service in the United States, call 1-800-211PANA (7262) or visit
Panasonic Web Site: http://www.panasonic.com
For assistance in Puerto Rico, call Panasonic Sales Company (787)750-4300 or fax (787)-768-2910.
CAR AUDIO PRODUCT – ONE (1) YEAR, PARTS AND LABOUR
(The labour to install or remove the product is not warranted)
LIMITED WARRANTY LIMITS AND EXCLUSIONS
This warranty ONLY COVERS failures due to defects in materials and
workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages
which occurred during shipment, failures which are caused by products not supplied by the warrantor, failures which result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustment, maladjustment of consumer control, improper maintenance, improper antenna, inadequate
signal reception or pickup, power line surge, improper voltage supply, lightning, modification, commercial use (such as use in hotels,
offices, restaurants, or other business uses) or rental use of the
product, or service by anyone other than the technician from Factory
Servicenter or other authorized service centers, or damage that is
attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED
UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS
NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT
OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes
damages for lost time, cost of having someone remove or re-install
an installed unit if applicable, travel to and from the sevicer, and loss
of media, data or other memory contents. The items listed are not
exclusive, but are for illustration only.) ALL EXPRESS AND IMPLIED
PANASONIC PRODUCT LIMITED WARRANTY
Panasonic Canada Inc. warrants this product to be free from defects
in materials and workmanship and agrees to remedy any such defect
for a period as stated below from the date of original purchase.
Before Reading These Instructions
PANASONIC CONSUMER ELECTRONICS COMPANY,
DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA
One Panasonic Way, Secaucus, New Jersey 07094
English
WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
U.S.A.
LIMITATIONS AND EXCLUSIONS
This warranty does not apply to products purchased outside Canada
or to any product which has been improperly installed, subjected to
usage for which the product was not designed, misused or abused,
damaged during shipping, or which has been altered or repaired in
any way that affects the reliability or detracts from the performance,
nor does it cover any product which is used commercially. Dry cell
batteries are also excluded from coverage under this warranty.
This warranty is extended to the original end user purchaser only. A
purchase receipt or other proof of the original purchase date is
required before warranty service is performed.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES.
In certain instances, some jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages, or the exclusion of
implied warranties, so the above limitations and exclusions may not
be applicable.
CQ-C7403U/C7303U/C7203U/C7103U
7
Features
Hands-Free Phone System
Connection of the optional Hands-Free Phone System (HandsFree Kit featuring Bluetooth® technology: CY-BT100U) allows
users to talk on a handsfree cellular phone if the phone
supports Bluetooth.
Note: This unit is designed only for receiving calls. It cannot
send calls.
Bluetooth®
The Bluetooth word mark and logo are owned by the
Bluetooth SIG, Inc. and any use of such marks by
Matsushita Electric Industrial Co.,Ltd. is under license.
Other trademarks and trade name are those of their
respective owners.
Expansion Module (hub unit)
Connection of the Expansion Module (hub unit, CY-EM100U)
allows users to connect up to 4 optional devices shown below.
Even simultaneous connection of the Sirius Satellite Radio and
XM Satellite Radio is feasible.
Wide array of components for system upgrade
Various optional components allow users to obtain availability
of wide range of system upgrade. Upgrading the system
delivers relaxed AV space in a car. For further information, refer
to the separate System Upgrade Guidebook.
¡ DVD Changer
The optional adapter (Conversion Cable for DVD/CD
Changer: CA-CC30U) allows you to connect the optional Panasonic DVD changer unit (CX-DH801U).
Sound Control
SQ (Sound Quality)
You have six preset modes (FLAT, ROCK, POP, VOCAL, JAZZ,
CLUB). You can customize your settings for these and save
them for instant recall.
SQ7
This is 7-band equalizer with 60, 160, 400, 1 k, 3 k, 6 k, and 16
kHz. Each band is adjustable between – 12 dB and 12 dB in
steps of 2 dB.
SQ3
This is 3-band equalizer: Band 1 covers 60, 80, 100, and 200
Hz, Band 2 covers 0.5 k, 1 k, 2 k, and 3 kHz, and Band 3 covers
10 k, 12 k, 15 k, and 18 kHz. Each band is adjustable between
– 12 dB and 12 dB in steps of 2 dB.
D·M (Direct Memory)
You can assign your favorite broadcasting station to the
[D·M] button. As the result of doing that, your favorite
broadcasting station can be received even if the unit is in
the CD mode or other modes. (a page 20)
Customize
Initially stored moving images and still images are editable to
taste. IMAGE STUDIO* allows you to process images from a
digital camera or other devices without difficulty. (a page 31)
* This software is downloadable from Panasonic Web site
(http://panasonic.co.jp/pas/en/software/customize/index.html)
¡ CD Changer
The optional adapter (Conversion Cable for DVD/CD
Changer: CA-CC30U) allows you to connect the optional Panasonic CD changer unit (CX-DP880).
¡ iPod®
The optional adapter (Direct Cable for iPod: CA-DC300U)
allows you to connect the optional iPod series.
iPod is a trademark of Apple Computer, Inc., registered in
the U.S. and other countries.
¡ XM Satellite Radio
You can connect the optional XM receiver (XMD-1000)
with optional Digital Adapter. For details, refer to the
operating instructions for the XM receiver.
¡ Sirius Satellite Radio
You can connect the optional Sirius Satellite radio
receiver (SIR-PAN1).
8
CQ-C7403U/C7303U/C7203U/C7103U
Contents
English
78
Common
Español
¡Safety Information
¡Before Reading These Instructions
¡Features
¡Controls Layout
¡Preparation (Clock adjustment etc.)
¡General
¡Sound Control
2
4
8
10
12
14
18
Each
Source
40
¡Radio
¡CD Player
¡MP3/WMA Player
20
22
24
As Needed
Français
¡Audio Setting
¡Function Setting (Security Setting etc.)
¡Display Setting
¡Customize the Display
¡Troubleshooting
¡Error Display Messages
¡Notes on Discs
¡Maintenance
¡Specifications
28
29
30
31
33
37
38
38
39
CQ-C7403U/C7303U/C7203U/C7103U
9
Controls Layout
Note: This instruction manual explains operations for use with the buttons on the main unit. (Different operations excluded)
u TILT (eject) (a page 15)
OPEN (a page 15)
VOLUME (a page 15)
PUSH SEL Select (a page 28)
SRS WOW (a page 18)
P·SET Preset (a page 21)
DISC (a System Upgrade
Guidebook)
FOLDER (a page 24)
Main Unit
MUTE (a page 15)
SBC-SW (a page 19)
DISP Display (a page 17)
y / 5 Pause/Play
(a page 22, 24)
BAND (a page 20)
SET (a page 29, 30)
APM Auto Preset Memory
(a page 21)
TUNE (a page 20)
TRACK (FILE)
(a page 22, 24)
SQ Sound Quality
(a page 19)
Remote control sensor
MENU (a page 29, 30)
DIM Dimmer (a page 17)
SRC/PWR Source/Power
(a page 14, 16)
Release (a page 14)
D·M Direct Memory
(a page 20)
When Face Plate
Opens
Disc slot
10
CQ-C7403U/C7303U/C7203U/C7103U
#
Remote Control Unit
NUMBER
–
9
VOL Volume
}:Up
{:Down
SEL Select
MENU
Number
RANDOM
4
0 to 9
POWER
SRC (SOURCE)
RANDOM
POWER
SOURCE MENU
SEL
SRC
SCAN
5
REPEAT
6
7
SCAN
REPEAT
9
VOL
SET
BAND
Pause/Play
SET
APM Auto Preset
Memory
BAND
MUTE
1
2
3
RANDOM
SCAN
REPEAT
4
5
6
7
8
9
0
DISP
TUNE
TUNE
#
TUNE
TRACK (FILE)
MUTE
SBC-SW Super Bass
Control-Subwoofer
NUMBER
DISP Display
CAR AUDIO
8
0
Controls Layout
0
English
Number Buttons
Operations executable only with main unit/
operations executable only with remote control
P·SET (Preset)
DISC (FOLDER)
Although most of the functions of this unit are executable
with both the main unit and remote control, the following
functions are excluded.
Operations executable only with main unit
¡ Face panel’s opening, closing, tilting, and removal
actions (a page 15)
¡ Disc ejection (a page 15)
¡ Dimmer (a page 17)
¡ SRS on, off, and adjustment (a page 18)
¡ SQ on, off, and adjustment (a page 19)
¡ Direct memory setting and calling (a page 20)
Operations executable only with remote control
¡Preset station calling with one-touch operation
(a page 21)
¡ Direct access to tracks on CDs (a page 23, 25)
¡ Random and repeat play with one-touch operation
(a page 23, 25)
¡ Scan playback (a page 23, 25)
CQ-C7403U/C7303U/C7203U/C7103U
11
Cancellation of demonstration screen
Preparation
For the first use, the following screen may appear
repeatedly.
5 Press [{] or [}] to select
“DEMONSTRATION”.
1 Set your car's ignition switch to the ACC
or On position.
The demonstration screen appears.
6 Press [BAND] (SET) to select “OFF”
[MENU].
7 Press
For using the remote control, hold down [SEL]
2 Press [SRC/PWR] (Power).
3 Press [MENU] to display the menu
(MENU) for 2 sec. or more.
Note: This unit is operable as usual even if the
demonstration screen is activated. The demonstration
screen automatically appears if no operation is executed
for 1 minute.
display.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
4 Press []] or [[] to display the
DISPLAY menu.
Preparation Before Initial Use
Warning
Pull the insulation film out
from the backside of
remote control gently.
Keep batteries and insulation film out of reach of
infants. If an infant ingests a battery, please seek
immediate medical attention.
Remote Control Preparation
Cautions
Insulation film
Battery Replacement
q Remove the battery holder
with the remote control unit
placed on a flat surface.
q Stick your thumbnail into
the groove, and push the
holder in the direction of
the arrow, and at the
same time.
w Pull it out in the direction
of the arrow using a
tough pointed object.
Tough pointed object
w
q
¡Remove and dispose of an old battery immediately.
¡Do not disassemble, heat or short a battery. Do not
throw a battery into a fire or water.
¡Follow local regulations when disposing of a battery.
¡Improper use of a battery may cause overheating, an
explosion or ignition, resulting in injury or a fire.
Note: Battery Information:
Battery Type: Panasonic lithium battery (CR2025)
(Included in the remote control)
Battery Life: Approximately 6 months under normal use
(at room temperature)
Back side
w Put a battery in the case with
(+) side facing up.
e Put the case back.
2
3
12
CQ-C7403U/C7303U/C7203U/C7103U
¡ The alarm sounds and the message appears on the
screen to warn you to remove the face plate at ACC
off.
Security Indicator
Preparation
You may need to set the following depending on the
devices to be connected.
Using Subwoofer
Other Settings
¡ Subwoofer level adjustment (a page 28)
¡ Subwoofer low pass filter (a page 28)
Note: Other settings are required when a Sirius receiver,
an XM receiver, or a Hands-Free Phone System is
connected. (a System Upgrade Guidebook)
Note: Adjust the clock when “ADJUST” appears on the
display.
Clock adjustment
English
Security Function
Setting
The following functions are activated when the Security
Function is ON. (a page 29)
¡ The security indicator lights up when removing the
face plate.
5 Adjust the setting value.
1 Press [MENU] to display the menu
display.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
2 Press []] or [[] to display the
DISPLAY menu.
3 Press [{] to select “CLOCK ADJ”.
4 Press [BAND] (SET) to confirm the
display.
[[]: Adjusting minutes
[]]: Adjusting hours
[}]: Forward
[{]: Backward
6 Press [BAND] (SET) to confirm the
adjustment.
7 Press [MENU].
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
CQ-C7403U/C7303U/C7203U/C7103U
13
General
This chapter explains how to turn on or off the power, how to adjust the volume, etc.
Power on
(PWR: Power)
Power On/off
Press [SRC/PWR] (PWR: Power).
Power off
Hold down [SRC/PWR] (PWR: Power) until
you hear a beep, then release it.
14
3 Put the face
plate in the case.
Removing
Mounting
1 Turn off the power (a page 14)
2 Press [ ]
1 Slide the left side of the face plate in
place.
(Release).
(Anti-Theft System)
Face Plate Removing/Mounting
You can remove the face
plate to prevent it from
being stolen.
(The face plate disengages with a click
when it is removed.)
The face plate automatically closes after a lapse of 5
seconds while it is open.
The power is automatically turned off while the unit
is active.
Cautions:
¡ It is recommended to remove or mount the face
plate when the plate is at the closed position.
Do not remove or mount the face plate when the
plate is in motion.
¡ This face plate is not waterproof. Do not expose it to
water or excessive moisture.
¡ Do not remove the face plate while driving your car.
2 Press the right end of the face plate
until “click” is heard.
¡ Do not place the face plate on the dashboard or
nearby areas where the temperature rises to high
levels.
¡ Do not touch the contacts on the face plate or on the
main unit, since this may result in poor electrical
contacts.
¡ If dirt or other foreign substances get on the contacts, wipe them off with clean and dry cloth.
¡ To avoid damaging the face plate, do not push it
down or place objects on it while it is open.
CQ-C7403U/C7303U/C7203U/C7103U
Open/Eject
English
When a disc is already loaded, the disc will automatically
be ejected.
Tilt
Cautions:
¡ To avoid damaging the face plate, do not push it
down or place objects on it while it is open.
¡ Do not pinch your finger or hand in the face plate.
¡ Do not insert foreign objects into the disc slots.
¡ For the following cases, the face plate automatically closes. Use caution not to catch your finger.
¡ After a lapse of 20 seconds
¡ When a disc is inserted
¡ When the face plate is removed (a page 14)
¡ When ACC is set to off
The display angle changes among 4 levels as follows
every time you hold down [u TILT] (OPEN) for 1 sec.
or more and release.
Note: The last selected
angle is memorized even
after turning off the power.
Close
General
(OPEN/CLOSE, TILT)
Face Plate Motion (Open/Close, Tilt)
Press [u TILT] (OPEN).
TILT 1
TILT 2
TILT 3
OPEN
Press [u TILT] (OPEN).
(VOLUME)
q Up
w Down
Notes:
¡ The volume level can be set independently for each
source. (For radio, one volume setting for AM, one
volume setting for all FMs)
¡ The volume is not adjustable while an error display is
on the monitor. (a page 37)
¡ This unit memorizes individual volume levels for each
source. Make volume adjustments of each source
appropriately to prevent large volume fluctuation when
the source is changed.
Setting Range: 0 to 40
Default: 18
Volume off (down)
Press [MUTE].
MUTE (ATT: Attenuation)
Temporary Volume Off (Down)
Volume Adjustment
TILT OFF
Cancel
Press [MUTE] again.
Note: Volume-down range can be specified.
(a page 29)
CQ-C7403U/C7303U/C7203U/C7103U
15
General
The source changes as follows every time
[SRC/PWR] (SRC: Source) is pressed.
Radio
System-up Connector
FM1, FM2, FM3, AM (a page 20)
Player
Device connected to the System-up Connector of the
this unit
When optional devices are connected:
Shift to connected devices
When an expansion module is connected:
The devices connected to the ports 1 to 4 are activated
in sequence after shifting to AUX2 (devices connected
to the AUX terminal of the expansion module).
When connecting DVD Changer
When connecting CD Changer
(SOURCE)
Source Selection
When loading CD (a page 22)
When loading MP3/WMA disc (a page 24)
AUX 1
When connecting iPod
Device connected to the AUX terminal of the this unit
When connecting XM Receiver
When connecting Sirius Receiver
When connecting Expansion Module
Note: For information about connectable devices, refer
to the System Upgrade Guidebook or the instruction
manual for each device.
16
CQ-C7403U/C7303U/C7203U/C7103U
English
The display changes as follows every time [DISP] is
pressed.
Note: The graphic pattern and still image are selectable.
(a page 30)
At power-on:
Mode
(DISP: Display)
Display Change
Folder hierarchy (MP3/WMA mode only.)
Ordinary display + clock
Ordinary display + graphic pattern
General
Display OFF
All displays disappear in 5 seconds.
Only still image
Only graphic pattern
Ordinary display + still image
Note: The graphic equalizer of 19 bands (S.A.) is
selectable when selecting a graphic pattern.
At power-off:
Clock display (default)
Off
Brighter (default)
(DIM: Dimmer)
Dimmer Control
The dimmer level changes as follows every time you hold
down [MENU] (DIM:Dimmer) for 2 sec. or more.
Medium
Darker
Note: This setting is not adjustable with the remote
control.
CQ-C7403U/C7303U/C7203U/C7103U
17
Sound Control
SRS WOW
(CQ-C7403U, C7303U)
Only for CQ-C7403U/C7303U
SRS WOW™ is 3-D sound technology based on the HRTF
(Head Related Transfer Function) theory. Unlike
conventional audio systems, “natural 3-D sound field”,
“rich bass”, and “crisp and clear sound” can be obtained
at the same time in a wide area in front of speakers.
Holding down [VOLUME] (SRS WOW) for 2 sec. or
more toggles SRS WOW on and off.
Note: If you enable SRS WOW, the following functions
are automatically disabled:
SQ, BASS/TREBLE, BALANCE/FADER, HPF, SBC-SW
Lights when SRS WOW is activated.
You can make a fine adjustment to SRS WOW.
SRS TruBass®
1 Set the SRS WOW mode to on.
2 Hold down [SQ] for 2 sec. or more to
: Deep bass enhancement by application of the
bass reproduction technique of a pipe organ
(default)
display the audio menu display.
: No enhancement
SRS FOCUS®
Sound image movement in a vertical direction to make
sound crisp
3 Press [}] or [{] to select a function to
(SRS WOW Menu Display)
SRS WOW Setting
be adjusted.
: high (default)
: low
: off
4 Press [BAND] (SET) to adjust.
SRS®
: Surround function on (default)
: Surround function off
5 Press [DISP] to confirm the adjustment.
is a trademark of SRS Labs, Inc.
WOW technology is incorporated under license from
SRS Labs, Inc.
18
CQ-C7403U/C7303U/C7203U/C7103U
English
SQ changeover
The SQ category is changed every time [SQ] (Sound
Quality) is pressed.
Note: Setting of SQ, bass/treble and volume are
influenced one another. If the influence mentioned above
causes distortion to the audio signal, readjust bass/treble
or volume. (a page 28)
Lights when activated.
SQ is adjustable in accordance with your taste.
1 Hold down [SQ] (Sound Quality) for 2 sec.
or more when SRS WOW is disabled.
2 Press [BAND].
[]] [[]: Band selection
[}][{]: Level up/down
q / w: center frequency up/down
3 Adjust each band.
¡ CQ-C7403U/C7303U (SQ7)
4 Press [BAND] to determine the adjustment.
The screen of Step 1 appears again.
5 Press [DISP].
(USER)
SQ adjustment
The targeted SQ preset appears.
Sound Control
(SQ: Sound Quality)
SQ Selection Based on Genre
The equalizer curve is selectable from among preset 6
types (FLAT, ROCK, POP, VOCAL, JAZZ, and CLUB)
depending on your listening category.
Note: SQ is not changeable when SRS WOW is enabled.
(a page 18)
The regular screen appears again. “USER” appears in
the category name after adjustment.
Band: 60, 160, 400, 1 k, 3 k, 6 k, 16 k (Hz)
[]] [[]: Band selection
[}][{]: Level up/down
Note: If you hold down [BAND] for 2 sec. or more
on the SQ call-up screen, the presetting that is called
up can be turned into the default.
¡ CQ-C7203U/C7103U (SQ3)
Band: 60, 1 k, 10 k (Hz, default)
(SBC-SW: Super Bass Control-Subwoofer)
Substitutional Subwoofer
Only for CQ-C7403U/C7303U
The rear speaker can be used as a substitutional
subwoofer when a subwoofer is not connected.
Holding down [MUTE] (SBC-SW) for 2 sec.
or more toggles SBC-SW on and off.
Off (default)
Lights when
activated.
On
Notes:
¡ If ON is selected, the settings of subwoofer level
adjustment and subwoofer low pass filter are activated. (a page 28)
¡ SBC-SW is not changeable when SRS WOW is
enabled. (a page 18)
CQ-C7403U/C7303U/C7203U/C7103U
19
Radio
This chapter explains how to listen to the radio.
1 Press [SRC/PWR] (SRC: Source) to
select the radio mode.
2 Press [BAND] to select a band.
Operation Flow
3 Select a station.
Frequency adjustment
[]] (TUNE): Lower
[[] (TUNE): Higher
Note: Hold down for 0.5 sec. or more and release
for station search.
Preset station selection
[{] (P·SET: Preset): Lower preset number
[}] (P·SET: Preset): Higher preset number
Direct Memory
Radio Mode Display
Note: Direct selection can be executed with [1] to
[6] buttons on remote control.
Band
Preset Number
Lights while receiving an FM stereo signal.
You can assign your favorite broadcasting station to
the [D·M] button. As the result of doing that, your
favorite broadcasting station can be received even if
the unit is in the CD mode or other modes. (Default:
FM 87.9 MHz)
Note: For the use of an FM transmitter, it is useful
for users to register applicable frequencies on D.M
(Direct Memory).
D.M station Calling
Press [D.M] (Direct Memory).
D.M station Setting
q Select a station you would like to preset.
w Hold down [D.M] (Direct Memory) for 2 sec. or
more.
20
Frequency
CQ-C7403U/C7303U/C7203U/C7103U
Note: If the unit is turned off during receiving a broadcasting station via D·M, the unit starts again receiving
the broadcasting station via D·M by turning on the unit.
Station Preset
(APM: Auto Preset Memory, P·SET: Preset)
Auto Preset Memory (APM)
Stations with good receiving conditions automatically
preset.
1 Select a band.
2 Hold down
Manual station preset
1 Tune in to a station.
2 Hold down [}] or [{] for 2 sec. or
more.
English
Up to 6 stations can be preset in AM, FM1, FM2, and FM3
respectively.
Preset stations can be simply called up by pressing [}]
(P·SET) or [{] (P·SET).
Notes:
¡ Direct selection can be executed with [1] to [6] buttons on remote control.
¡ You can switch between 6 and 18 for FM presetting
stations. (EACH BAND/ALL BAND)
¡ Preset stations are changeable. (Preset Swap)
3 Select a preset number by pressing [}]
or [{].
Note:If [BAND] is pressed while receiving an FM
station, FM broadcasting is changeable among FM 1
to FM 3.
4 Hold down [BAND] (SET) for 2 sec. or
more to determine the selection.
[BAND] (APM)
for 2 sec. or
more.
The preset stations under best receiving conditions
are received for 5 sec. each after presetting the stations (SCAN). To stop scanning, press [}] or [{].
Notes:
¡ In step 2, a station can be registered by holding down
the numeric button [1] to [6] for 2 sec. or more.
¡ To stop presetting stations, press [DISP] (Display).
¡ The operation above allows users to replace the current station with the station preset in the selected
number while selecting a preset station.
Radio Menu Display
1 Press [MENU] to display the menu dis- 4 Press [MENU] to confirm the adjustplay.
ment.
For using the remote
control, hold down
[SEL](MENU) for 2
sec. or more.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
Radio
Note: New stations overwrite existing saved stations.
2 Press [}] or [{] to select a mode to be
adjusted.
3
Press [BAND]
(SET) to adjust.
PRESET
Preset range for FM bands
: Individual setting for FM1-3 each
(default)
: Setting of FM1-3 together
CQ-C7403U/C7303U/C7203U/C7103U
21
CD Player
When a disc is already loaded, press [SRC/PWR]
(SRC: Source) to select the CD mode.
1 Press [u TILT] (OPEN) to open the
face plate.
Operation Flow
When a disc is already loaded (
will automatically be ejected.
lights), the disc
2 Load a disc with the printed side facing
up.
The face plate closes automatically, and the unit recognizes the disc and starts playing automatically,
too.
Printed side
3 Select a desired portion.
Track selection
[7] (TRACK): Next track
[6] (TRACK): Preceding track (press twice)
Note: Hold down for fast forward/reverse.
Pause
Press [BAND] (h / 5).
Press again to cancel.
Note: The panel automatically closes after 20 seconds.
4 Press [u TILT] (OPEN) to eject the
disc.
CD Mode Display
Track number
22
CD-TEXT display
Notes:
¡ For scrolling text, hold down [DISP] for 2 sec. or
more.
¡ “NO TEXT” is displayed when there is no information
on the disc.
Time
Play Mode indicators
Lights when each mode is
activated.
CQ-C7403U/C7303U/C7203U/C7103U
Lights when the disc is
loaded.
¡ This unit does not support 8 cm (3”) discs.
¡ Do not use irregularly shaped discs. (a page 38)
¡ Do not use discs that have a seal or label attached.
¡ To avoid damaging the face plate, do not push it down or
place objects on it while it is open.
¡ Do not pinch your finger or hand in the face plate when the
face plate is in motion.
¡ Do not insert foreign matter into the disc slots.
¡ Refer to the section on “Notes on CD/CD Media (CD-ROM,
CD-R, CD-RW)” (a page 38).
¡ This unit does not support a MIX mode CD (a CD containing
both CD-DA and MP3/WMA data). In case of using such a
CD, problems may occur such as anacoustic playback.
English
Cautions:
1 Press [MENU] to display the menu display.
For using the remote
control, hold down
[SEL] (MENU) for 2
sec. or more.
RANDOM
: Off (default)
: Random playback
2 Press [}] or [{] to select a mode to be
adjusted.
REPEAT
: Off (default)
3 Press [BAND]
: Playing the current track repeatedly
(SET) to adjust.
TEXT (CD-TEXT)
: Enabled (default)
: Disabled
4 Press [MENU] to confirm the adjustment.
CD Player
(RANDOM, REPEAT)
Random, Repeat Play (CD Menu Display)
Random and Repeat play can be set.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
Functions Only by
Remote Control Unit
Play Mode Selection
SCAN play
One-touch operation is available for selecting a track
playing style by use of [RANDOM] or [REPEAT].
RANDOM
Press [RANDOM].
Press again to cancel.
REPEAT
Press [REPEAT].
Press again to cancel.
You can find your favorite track by playing first 10-sec. of
each track.
Press [SCAN].
Press again to cancel.
Direct Access
A track can be directly selected.
Example: track number 5
1 Press [#] (NUMBER).
2 Press [5].
3 Press [SET].
Note: To suspend direct
selection, press [DISP] (Display).
CQ-C7403U/C7303U/C7203U/C7103U
23
MP3/WMA Player
When a disc is already loaded, press [SRC/PWR]
(SRC: Source) to select the MP3/WMA mode.
1 Press [u TILT] (OPEN) to open the
face plate.
When a disc is already loaded (
will automatically be ejected.
lights), the disc
2 Load a disc with the printed side facing 3 Select a desired portion.
Operation Flow
up
Folder selection
The face plate closes automatically, and the unit recognizes the disc and starts playing automatically,
too. (It may take several minutes to start for a disc
that has a lot of files.)
[}] (FOLDER): Next folder
[{] (FOLDER): Preceding folder
File selection
Printed side
[7] (TRACK): Next file
[6] (TRACK): Preceding file (press twice)
Note: Hold down for fast forward/reverse.
Pause
Note: The panel automatically closes after 20 seconds.
Press [BAND] (h / 5).
Press again to cancel.
4 Press [u TILT] (OPEN) to eject the
disc.
File number
Time
Folder number
MP3/WMA Mode Display
File type indicator
Information Display
Notes:
¡ For scrolling text, hold down [DISP] for 2 sec. or
more.
¡ “NO TEXT” is displayed when there is no information
on the disc.
¡ ID3/WMA tag information is displayed for the album
name and title/artist name.
Play Mode indicators
Lights when each mode is
activated.
Lights when the disc is
loaded.
(Folder Random)
(Folder Repeat)
(Folder Scan)
24
CQ-C7403U/C7303U/C7203U/C7103U
1 Press [MENU] to display the menu display.
RANDOM
: Off (default)
: Random playback (disc)
For using the remote
control, hold down
[SEL] (MENU) for 2
sec. or more.
FOLDER RANDOM
: Off (default)
2 Press [}] or [{] to select a mode to be
adjusted.
3
: Random playback (folder)
REPEAT
Press [BAND]
(SET) to adjust.
: Off (default)
: Playing the current file repeatedly
FOLDER REPEAT
4 Press [MENU]
: Off (default)
to confirm the adjustment.
: Playing the current folder repeatedly.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
TEXT
: Folder name/File name (default)
: Album/Title (tag information)
: No display
FOLDER SCAN (1st file in each folder)
Functions Only by
Remote Control Unit
Play Mode Selection
One-touch operation is available for selecting a file
playing style by use of [RANDOM] or [REPEAT].
RANDOM, REPEAT
Press the button. Press again to cancel.
FOLDER RANDOM, FOLDER REPEAT
Hold down the button for 2 sec. or more. Hold
down again to cancel.
SCAN play
You can find your favorite file by playing first 10-sec. of
each file.
SCAN (All files)
MP3/WMA Player
(RANDOM, REPEAT)
Random, Repeat Play (MP3/WMA Menu Display)
Random and Repeat play can be set.
English
Notes:
¡ Refer to the section on “Notes on MP3/WMA” (a page 26)
¡ This unit does not support a MIX mode CD (a CD containing both CD-DA and MP3/WMA data). In case of using such a CD,
problems may occur such as anacoustic playback.
Hold down [SCAN] for 2 sec. or more. Hold down
again to cancel.
Direct Access
A file in the current folder can be directly selected.
Example: file number 5
1 Press [#] (NUMBER).
2 Press [5].
3 Press [SET].
Notes:
¡ For folder selection, enter a number after pressing [#]
(NUMBER) twice.
¡ To suspend direct selection, press [DISP] (Display).
Press [SCAN]. Press again to cancel.
CQ-C7403U/C7303U/C7203U/C7103U
25
MP3/WMA Player
What is MP3/WMA?
MP3 (MPEG Audio Layer-3) and WMA (Windows MediaTM
Audio) are the compression formats of digital audio. The
former is developed by MPEG (Motion Picture Experts
Group), and the latter is developed by Microsoft
Corporation. Using these compression formats, you can
record the contents of about 10 music CDs on a single
CD media (This figures refer to data recorded on a 650
MB CD-R or CD-RW at a fixed bit rate of 128 kbps and a
sampling frequency of 44.1 kHz).
Note: MP3/WMA encoding and writing software is not
supplied with this unit.
Points to remember when making MP3/WMA files
Notes on MP3/WMA
Common
¡ High bit rate and high sampling frequency are recommended for high quality sounds.
¡ Selecting VBR (Variable Bit Rate) is not recommended
because playing time is not displayed properly and
sound may be skipped.
¡ The playback sound quality differs depending on the
encoding circumstances. For details, refer to the user
manual of your own encoding software and writing
software.
MP3
¡ It is recommended to set the bit rate to “128 kbps or
more” and “fixed”.
WMA
¡ It is recommended to set the bit rate to “64 kbps or
more” and “fixed”.
¡ Do not set the copy protect attribute on the WMA file
to enable this unit to play back.
Display Information
Displayed items
¡ CD-TEXT
Disc title
Track title
¡ MP3 (ID3 tag)
Album name
¡ MP3/WMA
Folder name
File name
¡ WMA (WMA tag)
Album name
Title name/artist name
Title name/artist name
Displayable characters
¡ Displayable length of file name/folder name: within 64
characters. (Unicoded file and folder names are
reduced by half in the number of displayable characters.)
¡ Name files and folders in accordance with the standard of each file system. Refer to the instructions of
writing software for details.
¡ ASCII character set and special characters in each language can be displayed.
ASCII character set
A to Z, a to z, digits 0 to 9, and the following symbols:
(space) ! ” # $ % & ’ ( ) * + , - . / : ; < = > ? @ [ \ ] ˆ
_`{|}~
Notes:
¡ With some software in which MP3/WMA format files
have been encoded, the character information may not
be displayed properly.
¡ Undisplayable characters and symbols will be converted into an asterisk ( ).
*
Caution:
Never assign the “.mp3”, or “.wma” file
name extension to a file that is not in the
MP3/WMA format. This may not only produce noise from the speaker damage, but
also damage your hearing.
26
CQ-C7403U/C7303U/C7203U/C7103U
Supported file systems
ISO 9660 Level 1/Level 2, Apple Extension to ISO 9660,
Joliet, Romeo
Note: Apple HFS, UDF 1.50, Mix CD and CD Extra are
not supported.
Compression formats
(Recommendation: “Points to remember when making MP3/WMA files” on the previous page)
Compression method
Bit rate
VBR
Sampling frequency
MPEG 1 audio layer 3 (MP3)
32 k – 320 kbps
Yes
32, 44.1, 48 kHz
MPEG 2 audio layer 3 (MP3)
8 k – 160 kbps
Yes
16, 22.05, 24 kHz
Windows Media Audio Ver. 2, 7, 8, 9*
32 k – 192 kbps
Yes
32, 44.1, 48 kHz
* WMA 9 Professional/LossLess/Voice are not supported.
Folder selection order/file playback order
Maximum number of files/folders
¡ Maximum number of files: 511 (files + folders)
¡ Maximum number of files in one folder: 255
¡ Maximum depth of trees: 8
¡ Maximum number of folders: 255 (Root folder is
included.)
Notes:
¡ You can shorten the duration between data read and
playback by decreasing the quantity of files or folders,
or the depth of the hierarchy.
¡ This unit counts the number of folders irrespective of
the presence or absence of an MP3/WMA file.
¡ If the selected folder does not contain any MP3/WMA
files, the nearest MP3/WMA files in the order of playback will be played.
¡ Playback order may be different from other MP3/WMA
players even if the same disc is used.
¡ “ROOT” appears when displaying the root folder
name.
Root Folder
(Root Directory)
1
2
q
Folder Selection
4
3
e
w
6
–
8
r
8
7
Tree 2
1
File Selection
In the order
–
y
q
5
Tree 1
In the order
MP3/WMA Player
Notes on MP3/WMA (continued)
¡ The file extension “.mp3” or “.wma” should be
assigned to each file depending on the file format.
¡ This unit does not have a play list function.
¡ Although Multi-session recording is supported, the
use of Disc-at-Once is recommended.
English
Recording MP3/WMA files on a CD-media
¡ You are recommended to minimize the chances of
making a disc that contains both CD-DA files and
MP3/WMA files.
¡ If CD-DA files are on the same disc as MP3 or WMA
files, the songs may not play in the intended order,
or some songs may not play at all.
¡ When storing MP3 data and WMA data on the same
disc, use different folders for each data.
¡ Do not record files other than MP3/WMA files and
unnecessary folder on a disc.
¡ The name of an MP3/WMA file should be added by
rules as shown in the following descriptions and also
comply with the rules of each file system.
¡ You may encounter trouble in playing MP3/WMA files
or displaying the information of MP3/WMA files
recorded with certain writing software or CD
recorders.
Tree 3
t
y
Tree 4
Tree 8
(Max.)
Copyright
It is prohibited by copyright laws to copy, distribute and
deliver copyrighted materials such as music without the
approval of copyright holder except enjoying yourself
personally.
No warranty
Above description complies with our investigations as of
December 2005. It has no warranty for reproducibility
and displayability of MP3/WMA.
CQ-C7403U/C7303U/C7203U/C7103U
27
Audio Setting
Adjustment to each speaker and an optional subwoofer
1 Press [VOLUME]
(SEL: Select) to
display the
AUDIO menu
display.
2
clockwise or
counterclockwise
to adjust.
AUDIO Menu Display
(Setting range: L (left)15 to R (right) 15 and Center,
Default: Center)
q : Right enhanced
w : Left enhanced
Fader adjustment
Press [VOLUME] (SEL: Select) to select
a mode to be
adjusted.
3 Turn [VOLUME]
Notes:
¡ If no operation takes place for more than 10 seconds
in the audio menu (2 sec. in Main volume adjustment), the display returns to the regular mode.
¡ Only the main volume, subwoofer level, subwoofer
low pass filter, and rear level are adjustable when SRS
WOW is enabled. (a page 18)
Main volume adjustment
(Setting range: R (rear) 15 to F (front) 15 and Center,
Default: Center)
q : Front enhanced
w : Rear enhanced
Subwoofer level adjustment
(Setting range : mute (-∞), -6 dB to +6 dB, 2 dB Step,
Default: 0 dB)
q : Up
w : Down
Subwoofer Low Pass Filter
(Setting range: 80 Hz, 120 Hz, 160 Hz, Default: 80 Hz)
q : Up
w : Down
(Setting range: 0 to 40, Default: 18)
q : Up
w : Down
Subwoofer output range
Other speakers output ranges
High Pass Filter
Bass adjustment
(Setting range: -12 dB to +12 dB, 2 dB Step, Default:
Bass 0 dB)
q : Up
w : Down
Treble adjustment
28
Balance adjustment
Only for CQ-C7403U/C7303U
(Setting range: Filter OFF, 90 Hz, 135 Hz, 180 Hz, 225 Hz,
Default: Filter OFF)
q : Up
w : Down
Rear Level Adjustment (SRS WOW)
Only for CQ-C7403U/C7303U
(Setting range: -12 dB to +12 dB, 2 dB Step, Default:
Treble 0 dB)
q : Up
w : Down
(Setting range: 0 to –15, Default: –10)
q : Up
w : Down
Note: Do not activate SQ and Bass/Treble at same time
to avoid causing sound distortion.
Note: The rear level is adjustable only when SRS WOW
is enabled. (a page 18)
CQ-C7403U/C7303U/C7203U/C7103U
Function Setting
Adjustment to display on the FUNCTION menu
play.
For using the remote
control, hold down
[SEL] (MENU) for 2
sec. or more.
2 Press []] or [[] to display the FUNCTION menu.
MUTE KEY
Setting [MUTE] buttons’ functions
: Volume off (Default)
:
Volume down by 10 steps
:
Volume down by 5 steps
English
1 Press [MENU] to display the menu dis-
SECURITY
Setting the security function (a page 13)
: ON (Default)
3 Press [}] or [{] to select a function to
FUNCTION Menu Display
be adjusted.
BUILT-IN AMP
Only for CQ-C7403U/C7303U
4 Press [BAND]
You can toggle the integrated amplifier on and off.
: Amplifier on (Default)
(SET) to adjust.
: Amplifier off (when the external amplifier is used)
5 Press [MENU] to confirm the adjustment.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
lights when disactivated.
CQ-C7403U/C7303U/C7203U/C7103U
Audio Setting, Function Setting
: OFF
29
Display Setting
Adjustment to display on the DISPLAY menu
1 Press [MENU] to display the menu
GRAPHIC PATTERN
display.
(Setting range: 5 types, Default: All)
For using the remote
control, hold down
[SEL] (MENU) for 2
sec. or more.
Switching by []] or [[]
All:
Sequential display from pattern A to C.
Pattern A-C
S.A.:
19-band display (Spectrum analyzer)
2 Press []] or [[] to display the
DISPLAY menu.
3 Press [}] or [{] to select a function to
be adjusted.
STILL IMAGE PATTERN
4 Press [BAND]
(Setting range: 11types, Default: All)
DISPLAY Menu Display
(SET) to confirm
the display.
Switching by []] or [[]
All:
Sequential display from pattern 1 to 10
No.1-10
5 Adjust the setting value.
6 Press [BAND] (SET).
7 Press [MENU] to confirm the
adjustment.
For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.
CONTRAST
(Setting range: 1 to 5, Default: Contrast 3)
[[]: Tilting up view angle
[]]: Tilting down view angle
CLOCK ADJ
DEMONSTRATION
Switching by [BAND].
ON:
OFF:
Demonstration screen at no operation
(default)
Regular screen
Note: Adjust the clock when “ADJUST” appears on the
display.
[[]: Adjusting minutes
[]]: Adjusting hours
[}]: Forward
[{]: Backward
Notes:
¡ The graphic pattern and still image are changeable.
(a page 31)
¡ If corrupted data is selected, “DISPLAY FILE INCOMPLETE” appears. (a page 32)
30
CQ-C7403U/C7303U/C7203U/C7103U
Only for CQ-C7403/C7303U
You can edit the moving images and still images that are initially stored in the unit. You also can use the data that is downloaded from
the Panasonic Web site and the data that is stored with a digital camera or other devices and processed with exclusive software,
IMAGE STUDIO. See “Notes on Customize function” (a page 32) as well.
Note: Visit Panasonic Web site (http://panasonic.co.jp/pas/en/software/customize/index.html) for details.
Preparation:
Put the CD-R/RW that contains data to
be customized in hand.
6 Select a file.
English
Customize the Display (Customize Function)
1 If there is a disc inside, take out the
[}][{][]][[]:Select
[BAND] (SET): Confirm
2 Press
[SRC/PWR] to
select the CD
mode.
Notes:
¡ Files are automatically identified by their extensions, and target files are displayed.
¡ If “BACK” is selected, the screen of step 5
appears.
3 Hold down [SEL] for 4 sec. or more to
(CQ-C7403U, C7303U)
CUSTOMIZE Menu Display
display the menu screen.
7 For a moving image file or still image
file, select where to save the file.
4 Load a CD-R/RW that contains data.
Note:
¡ It may take time for the unit to identify the CDR/RW.
¡ Discs recorded by the packet writing software are
not supported.
5 Select an item to be customized.
[}][{]:
Select
[BAND] (SET): Confirm
[]][[]:
Select
[BAND] (SET): Confirm
Notes:
¡ New data overwrites existing data.
¡ If “BACK” is selected, the screen of step 6
appears.
8 Confirm the changed item.
Display Setting, Customize the Display (Customize Function)
disc.
[]][[]:
Select
[BAND] (SET): Confirm
Note: To exit the customize menu, hold down
[SEL] 4 sec. or more.
GRAPHIC PATTERN
Moving image (graphic pattern) data (a page 30)
STILL IMAGE
Still image data (a page 30)
OPENING MESSAGE
Moving image at power on
CLOSING MESSAGE
Moving image at power off
Customization is performed. Do not turn off the
power in mid-operation. (It takes approx. 1 minutes
to complete this operation for a 168 kB moving
image.) After completion of this operation, the
screen of step 5 appears.
Note: If “NO” is selected, the screen of step 5
appears.
9 Press [OPEN] to eject the disc.
10 Hold down [SEL] for 4 sec. or more.
The CD mode comes back.
CQ-C7403U/C7303U/C7203U/C7103U
31
Customize the Display (Customize Function)
Note on Download Service
At Customizing
The download service may be suspended or stopped
without advance notice. The download service is not
available in some areas. Please visit the site below for
further information.
Panasonic Web site:
(http://www.panasonic.co.jp/global/)
¡ If customizing is interrupted on account of turning off
the power, stopping the engine, removing the face
plate or other reasons, you may lose the data. In such
a case, try customizing again.
¡ The default image exists on the Panasonic Web site. If
you would like to restore it, download the image from
the site.
Download site:
Notes on IMAGE STUDIO
¡ This download service is not available in some areas.
For details, please access the Panasonic website.
¡ IMAGE STUDIO is available only by downloading from
the address below. It is not bundled with this unit.
¡ Refer to the downloaded operating manual for how to
use IMAGE STUDIO.
Notes on Customize Function
Error Display Messages
NO FILES DETECTED
No customize-specific data on the disc
a Load a disc that contains customize-specific
data.
Notes on File
32
http://panasonic.co.jp/pas/en/software/
customize/index.html
¡ The customize-specific file is downloadable from the
URL below. You can create exclusive files stored with
a digital camera or other devices by using exclusive
software, IMAGE STUDIO that can be accessed from
the same URL.
¡ Do not change the extension. Otherwise, the data cannot be recognized.
CUSTOMIZING FAILED
Customize failed
a Check to see whether or not the extension is correct and file contents are appropriate.
DISPLAY FILE INCOMPLETE
At Disc Making
¡ Save only customize-specific data.
¡ Save all data in the root directory. Files contained in a
folder cannot be recognized.
¡ Follow the table below with regard to the number of
files that are saved to a disc. Files beyond the specified capacity are not readable.
¡ Discs recorded by the packet writing software are not
supported.
Type
Extension
GRAPHIC PATTERN
.pfm
10
STILL IMAGE
.pfs
15
OPENING MESSAGE
.pfo
5
CLOSING MESSAGE
.pfe
5
Intended moving image or still image is damaged.
a Customize it again and overwrite the file with
new one.
Max. number
CQ-C7403U/C7303U/C7203U/C7103U
Troubleshooting
Problem
No power to the
unit
Common
Sound is not
generated.
Noise
Warning
¡ Do not use the unit in an irregular condition, for
example, without sound, or with smoke or a foul
smell, which can cause ignition or electric shock.
Immediately stop using the unit and consult your
dealer.
¡ Never try to repair the unit by yourself because it is
dangerous to do so.
Possible cause a Possible solution
The power cord (battery, power and ground) is connected in the wrong way.
a Check the wiring.
Fuse blows out.
a Eliminate the cause of fuse blowout and replace the fuse with new one.
Consult your dealer.
MUTE is set to ON.
a Set MUTE to OFF.
The wiring of speaker lines are not correct, or a break or poor contact arises.
a Check the wiring in accordance with the wiring diagram. (Installation
Instructions)
There is an electromagnetic-wave generator such as a cellular phone near the unit or
its electrical lines.
a Keep an electromagnetic-wave generator such as a cellular phone away from
the unit and the wiring of the unit. In case that noise cannot be eliminated
due to the wiring harness of the car, consult your dealer.
Customize the Display (Customize Function), Troubleshooting
Check and take steps as described below.
If the described suggestions do not solve the problem, it is
recommended to take the unit to your nearest authorized Panasonic
Servicenter. The product should be serviced only by qualified personnel.
Please refer the checking and the repair to professionals. Panasonic
shall not be liable for any accidents arising out of neglect of checking the
unit or your own repair after your checking.
Never take measures especially those other than indicated by italic
letters in “Possible Solution” described below because those are too
dangerous for users to handle themselves.
English
If You Suspect Something Wrong
The contact of the ground lead is poor.
a Make sure that the ground lead is connected to an unpainted part of the chassis securely.
Noise is made in
step with engine
revolutions.
Alternator noise comes from the car.
a Change the wiring position of the ground lead.
a Mount a noise filter on the power supply.
CQ-C7403U/C7303U/C7203U/C7103U
33
Troubleshooting
Problem
Some operations
are not executable.
Common (continued)
No sound from
speaker(s)
The speaker
channels are
reversed between
right and left.
The sound field is
not clear in the
stereo mode.
Central sound does
not settled.
The power fails
unintentionally.
Poor reception or
noise
Possible cause a Possible solution
Some operations are not executable in particular modes such as menu mode.
a Read the operating instructions carefully and cancel the mode. If the unit is
still out of order, consult your dealer.
BALANCE/FADER setting is not appropriate.
a Readjust BALANCE/FADER.
There is a break, a short circuit, poor contact or wrong wiring regarding the speaker
wiring.
a Check the speaker wiring.
The speaker wiring is confused between right and left.
a Perform the speaker wiring in accordance with the wiring diagram.
The plus and minus terminals at right and left channels of speakers are connected
reversely.
a Perform the speaker wiring in accordance with the wiring diagram.
The safety device works.
a Consult your dealer, or your nearest Panasonic Servicenter.
Antenna installation or wiring of antenna cable is faulty.
a Check whether the antenna mounting position and its wiring are correct. In
addition, check to see whether the antenna ground is securely connected to
the chassis.
Radio
No power is supplied to the antenna amplifier (when using a film antenna, etc.).
a Check the wiring of the antenna battery lead.
The number of auto
preset stations is
less than 6.
Preset stations
cannot be stored.
34
The number of receivable stations is less than 6.
a Move to an area where receivable stations number is maximum, and try presetting.
The contact of the battery lead is poor, or the battery lead is not always powered.
a Make sure that the battery lead is connected securely, and preset stations
again.
CQ-C7403U/C7303U/C7203U/C7103U
No playback or
disc ejected
CD
Sound skipping or
noise
Sound skipping
due to vibration
Disc unejectable
Possible cause a Possible solution
The disc is inserted upside down.
a Insert a disc correctly.
There is a flaw or foreign material on the disc.
a Remove the foreign material, or use a flawless disc.
English
Problem
There is a flaw or foreign material on the disc.
a Remove the foreign material, or use a flawless disc.
The unit is not sufficiently secured.
a Secure the unit to the console box.
The unit is tilted at over 30˚ in the front-to-end direction.
a Make the angle 30˚ or less.
Something such as a peeled label obstructs the disc coming out.
a Press and hold the [u] (OPEN) for more than 2 seconds when the face plate
is open (disc forced ejection). In case that the disc forced ejection does not
work, consult your dealer.
MP3/WMA
No playback or
disc ejected
The disc has unplayable formatted data.
a Refer to the description about MP3/WMA for playable sound data except CDDA (i.e. music CD).
The CD-R/RWs that
are playable on
other devices are
not playable on
this unit.
The playability of some CD-R/RWs may depend on the combination of media,
recording software and recorder to be used even if these CD-R/RWs are playable on
other devices such as a PC.
a Make CD-R/RWs in different combination of media, recording software and
recorder after referring to the description about MP3/WMA.
Sound skipping or
noise
Troubleshooting
The microcontroller in the unit operates abnormally due to noise or other factors.
a Unplug the power cord and plug it again. In case the unit is still out of order,
consult your dealer.
There is a flaw or foreign material on the disc.
a Remove the foreign material, or use a flawless disc. For MP3/WMA, refer to
the description about MP3/WMA.
Playing VBR (Variable Bit Rate) files may cause sound skipping.
a Play Non-VBR files.
CQ-C7403U/C7303U/C7203U/C7103U
35
Troubleshooting
Problem
Possible cause a Possible solution
The battery is inserted in the wrong direction. A wrong battery is inserted.
aInsert a correct battery in the correct direction.
The battery is weak.
aReplace the battery with new one.
Remote control unit
No response to
pressing buttons
36
The aiming direction of the remote control unit is wrong.
aAim the remote control unit at the sensor of the unit and press buttons.
The sensor is exposed to direct sunlight. (The remote control unit may not be
operable when the sensor is exposed to direct sunlight. In such a case, the
system is not faulty.)
aBlock off sunlight to the sensor.
CQ-C7403U/C7303U/C7203U/C7103U
Error Display Messages
Display
The disc is dirty, or is upside down.
a Check the disc.
The disc has scratches.
a Check the disc.
English
Possible cause a Possible solution
The player for some reason cannot read the file you are trying to play. (File recorded
in an unsupported file system, compression scheme, data format, file name extension, damaged data, etc.)
a Select a file that the player can read. Check the type of data recorded on the
disc. Create a new disc if necessary.
(After 5 seconds)
A WMA file can be copyrighted.
a The file protected by copyright is not playable.
To next file automatically
No disc.
Note: Refer to the System Upgrade Guidebook for error messages regarding optional products.
CQ-C7403U/C7303U/C7203U/C7103U
Troubleshooting, Error Display Messages
CD/MP3/WMA
No operation by some cause.
a Unplug the power cord and plug it again. In case the unit is still out of order,
consult your dealer. (a Installation Instructions)
37
Notes on
CD-Rs/RWs
Notes on CD/CD Media (CD-ROM, CD-R, CD-RW)
Notes on Discs
If you use commercial CDs, they must have
either of these labels shown at right.
Some copy-protected music CDs are not
playable.
TEXT
How to hold the disc
¡ Do not touch the underside of the disc.
¡ Do not scratch on the disc.
¡ Do not bend the disc.
¡ When not in use, keep disc in the case.
Printed side
Do not use irregularly shaped discs.
Do not leave discs in the following places:
¡ In direct sunlight
¡ Near car heaters
¡ Dirty, dusty and damp areas
¡ On seats and dashboards
Labels created by a printer Irregularly shaped discs
Disc cleaning
Use a dry, soft cloth to wipe from the center outward.
Do not attach any seals or labels to your discs.
Do not write on the disc label with a ballpoint
pen or other hard-point pens.
<Correct>
<Wrong>
¡ You may have trouble playing back some CD-R/RW discs recorded on CD recorders (CD-R/RW drives), either due
to their recording characteristics or dirt, fingerprints, scratches, etc. on the disc surface.
¡ CD-R/RW discs are less resistant to high temperatures and high humidity than ordinary music CDs. Leaving them
inside a car for extended periods may damage and make playback impossible.
¡ Some CD-R/RWs can not be played back successfully thanks to incompatibility among writing software, a CD
recorder (CD-R/RW drive) and the discs.
¡ This player cannot play the CD-R/RW discs if the session is not closed.
¡ This player cannot play the CD-R/RW discs which contains other than CD-DA or MP3/WMA data.
¡ Be sure to observe the instructions of CD-R/RW disc for handling it.
Cleaning the
Unit
Maintenance
Your product is designed and manufactured to ensure the minimum of maintenance. Use a soft cloth for
routine exterior cleaning. Never use benzine, thinner, or other solvents.
Fuse
If the fuse blows out, consult your dealer, or your nearest authorized Panasonic Servicenter.
38
Warning
¡Use fuses of the same specified rating (15 A). Using substitutes or fuses with higher ratings, or connecting the
unit directly without a fuse could cause fire or damage to the unit. If the replaced fuse fails, contact your
nearest authorized Panasonic Servicenter.
CQ-C7403U/C7303U/C7203U/C7103U
Sampling Frequency
DA Converter
Pick-Up Type
Light Source
Wavelength
Frequency Response
Signal to Noise Ratio
Total Harmonic Distortion
Wow and Flutter
Channel Separation
8 times oversampling
4 DAC System
Astigma 3-beam
Semiconductor laser
790 nm
20 Hz – 20 kHz (±1 dB)
96 dB
0.01 % (1 kHz)
Below measurable limits
75 dB
General
CD Player
Stereo Radio
FM
Frequency Range
Usable Sensitivity
50 dB quieting Sensitivity
Frequency Response
Alternate channel selectivity
Stereo Separation
Image response ratio
IF response ratio
Signal to noise ratio
87.9 MHz – 107.9 MHz
10.2 dBf (0.9 µV, 75Ω)
15.2 dBf (1.6 µV, 75Ω)
30 Hz – 15 kHz (±3 dB)
75 dB
35 dB (at 1 kHz)
75 dB
100 dB
62 dB
Notes on discs, Maintenance, Specifications
Variable Range of Equalizer
Current Consumption
Maximum Power Output
Speaker Impedance
Pre-amp output voltage
Subwoofer-output voltage
Pre-amp output impedance
Subwoofer-output impedance
Dimensions (Main Unit)
Weight (Main Unit)
DC 12 V (11 V – 16 V), Test Voltage 14.4 V, Negative Ground
Bass; ±12 dB at 60 Hz, Treble; ±12 dB at 16 kHz
60, 160, 400, 1 k, 3 k, 6 k, 16 k Hz (CQ-C7403U/C7303U), Band 1 (60, 80,
100, 200 Hz), Band 2 (500, 1k, 2k, 3k Hz), Band 3 (10k, 12k, 15k, 18k Hz)
(CQ-C7203U/C7103U)
-12 dB to 12 dB (2 dB step)
Less than 2.2 A (CD mode, 0.5 W 4-Speaker)
50 W x 4 (at 1 kHz)
4–8Ω
5 V (CQ-C7403U/C7203U), 2.5 V (CQ-C7303U), 2V (CQ-C7103U) (CD mode, 1 kHz, 0 dB)
5 V (CQ-C7403U/C7203U), 2.5 V (CQ-C7303U), 2V (CQ-C7103U) (CD mode, 1 kHz, 0 dB)
60 Ω (CQ-C7403U/C7203U), 200 Ω (CQ-C7303U/C7103U)
60 Ω (CQ-C7403U/C7203U), 200 Ω (CQ-C7303U/C7103U)
178(W) x 50(H) x 155(D) mm {7” x 1 15/16 ”x 6 1/8”}
1.6 kg {3 lbs. 8 oz}
Power Supply
Tone Controls (Bass/Treble)
Equalizer Center Frequency
English
Specifications
AM
Frequency Range
Usable Sensitivity
Power Output:
18 W RMS x 4 Channels at 4 Ω and ≤ 1%
THD+N
Signal to Noise Ratio:
78 dBA (reference: 1 W into 4 Ω)
530 kHz – 1 710 kHz
27 dB/µV (S/N 20 dB)
Above Specifications comply with EIA standards.
Notes:
¡Specifications and design are subject to modification
without notice due to improvements.
¡Some figures and illustrations in this manual may be
different from your product.
CQ-C7403U/C7303U/C7203U/C7103U
39