- No category
advertisement
BIOS
SECTION
S6130
L i f e B o o k S S e r i e s N o t e b o o k B I O S
S Series BIOS
BIOS SETUP UTILITY
The BIOS Setup Utility is a program that sets up the operating environment for your notebook. Your BIOS is set at the factory for normal operating conditions, therefore there should be no need to set or change the
BIOS environment to operate your notebook.
The BIOS Setup Utility configures:
■
■
Device control feature parameters, such as changing
I/O addresses and boot devices.
System Data Security feature parameters, such as passwords.
Entering the BIOS Setup Utility
To enter the BIOS Setup Utility do the following:
1. Turn on or restart your notebook.
2. Press the [F2] key when a message appears under the
Fujitsu logo prompting you to “Press <F2>: BIOS
Setup”. This will open the main menu of the BIOS
Setup Utility with the current settings displayed.
3. Press the arrow keys to scroll through the other setup menus to review or alter the current settings.
Navigating Through the Setup Utility
The BIOS setup utility consists of six menus: Main,
Advanced, Security, Boot, Info and Exit. This document explains each menu in turn including all submenus and setup items.
The following procedures allow you to navigate the setup utility menus:
1. To select a menu, use the cursor keys:
[ ], [ ].
2. To select a field within a menu or a submenu, use the cursor keys:
[ ], [ ].
3. To select the different values for each field, press the
[Spacebar] to change to the next higher selection and [F5] or [-] to go to the next lower selection.
4. To activate a submenu press the [Enter] key.
5. To return to a menu from a submenu, press the
[Esc] key.
6. To go to the Exit menu from any other menu, press the [Esc] key.
P O I N T S
■ Selecting a field causes a help message about that field to be displayed on the right-hand side of the screen.
■
Pressing the Enter key with the highlight on a selection that is not a submenu or auto selection will cause a list of all options for that item to be displayed.
Pressing the Enter key again will select the highlighted choice.
7. Pressing the [F9] key resets all items in the BIOS to the default values.
8. Pressing the [F10] key saves the current configuration and exits the BIOS Setup Utility. You will be asked to verify this selection before it is executed.
9. Pressing the [F1] key gives you a general help screen.
Entering the Setup Utility After a Configuration
Change or System Failure
If there has been a change in the system configuration that does not agree with the parameter settings stored in your BIOS memory, or there is a failure in the system, the system beeps and/or displays an error message after the Power On Self Test (POST). If the failure is not too severe, it will give you the opportunity to modify the settings of the setup utility, as described in the following steps:
1. When you turn on or restart the computer there is a beep and/or the following message appears on the screen:
Error message - please run SETUP program Press <F1> key to continue,
<F2> to run SETUP
2. If an error message is displayed on the screen, and you want to continue with the boot process and start the operating system anyway, press the [F1] key.
2
P O I N T S
■ If your notebook emits a series of beeps that sounds like a code and the display is blank, please refer to the
Troubleshooting section of your system Use’s Guide.
The Troubleshooting Section includes a list of error messages and their meanings.
■
If your data security settings require it, you may be asked for a password before the operating system will be opened.
3. If an error message is displayed on the screen, and you want to enter the setup utility, press the [F2] key.
4. When the setup utility starts with a fault present, the system displays the following message:
Warning!
Error message
[Continue]
5. Press any key to enter the setup utility. The system will then display the Main Menu with current parameters values.
M a i n M e n u
3
L i f e B o o k S S e r i e s N o t e b o o k B I O S
MAIN MENU – SETTING STANDARD SYSTEM PARAMETERS
The Main Menu allows you to set or view the current system parameters. Follow the instructions for Navigating Through The Setup Utility to make any changes.
(See Navigating Through the Setup Utility on page 2 for more information)
The following tables show the names of the menu fields for the Main menu and its submenus, all of the options for each field, the default settings and a description of the field’s function and any special information needed to help understand the field’s use. Note that the actual drive labels shown may vary.
P O I N T
System Time and System Date can also be set from your operating system without using the setup utility. Use the calendar and time icon on your Windows Control panel or type time or date from the MS-DOS prompt.
PhoenixBIOS Setup Utility
Main Advanced Security Boot Info Exit
Item Specific Help
System Time:
System Date:
[ 02 :34:56]
[05/06/2003]
Primary Master [FUJITSU MHS2030AT-(PM)]
Secondary Master [CD-224E-(SM)]
Language: [English (US)]
Adjust calendar clock.
<Tab>, <Shift-Tab>, or
<Enter> selects field.
F1 Help
ESC Exit
Select Item
Select Menu
-/Space Change Values
Enter Select Sub-Menu
Figure 1. Main Menu
Table 1: Fields, Options and Defaults for the Main Menu
Menu Field
System Time:
System Date:
Options
–—
–—
Default
–—
–—
F9 Setup Defaults
F10 Save and Exit
Description
Sets and displays the current time. Time is in a 24 hour format of hours:minutes:seconds with 2 digits for each. (HH:MM:SS).
Example: 16:45:57. You may change each segment of the time separately. Move between the segments with the [Tab] key and/or
[Shift] + [Tab] keys.
Sets and displays the current date. Date is in a month/day/year numeric format with 2 digits each for month and day and 4 digits for year. (MM/DD/YYYY) for example: 03/20/1998. You may change each segment of the date separately. Move between the segments with the [Tab] key and/or [Shift] + [Tab] keys.
4
M a i n M e n u
Table 1: Fields, Options and Defaults for the Main Menu
Menu Field
Primary
Master:
Options
Selects Primary
Master submenu
Default
The product # of the Hard Drive
Secondary
Master:
Language:
Selects Secondary
Master submenu
■
■
English (US)
Japanese (JP)
The product # of the CD drive
[English (US)]
Description
Display the type of device on this ATA/ATAPI interface, if there is one. Pressing the Enter key selects the Primary Master submenu allowing additional device configuration options for this interface.
Display the type of device on this ATA/ATAPI interface, if there is one. Pressing the Enter key selects the Secondary Master submenu allowing additional device configuration options for this interface.
The default setting differs between the US/European and the
Japanese model. Selects the display language for the BIOS.
5
L i f e B o o k S S e r i e s N o t e b o o k B I O S
Primary Master Submenu of the Main Menu
The Primary Master submenu identifies what ATA devices are installed.
Note that actual hard drive label shown may vary.
Depending on the drive type, information such as cylinders, heads and sectors may also be displayed.
PhoenixBIOS Setup Utility
Main
Primary Master [FUJITSU MHS2030AT-(PM)] Item Specific Help
Type: [ Auto ]
LBA Format
Total Sectors:
Maximum Capacity:
58605120
30006MB
Multi-Sector Transfers: [16 Sectors]
LBA Mode Control: [Enabled]
Transfer Mode:
Ultra DMA Mode:
[Multiword DMA 2]
[Disabled]
Select ATA/ATAPI drive installed here.
[Auto]
The BIOS auto-types the drive on boot time.
Except [Auto]
You enter parameters of the drive.
[None]
The drive is disabled.
Menu Field
Type:
LBA Format
Total Sectors:
Maximum
Capacity:
CHS Format
Cylinders:
F1
ESC
Help
Exit
Options
■
■
■
■
Auto
None
CD-ROM
Hard Disk
---
---
Select Item
Select Menu
-/Space
Enter
Change Values
Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
Figure 2. Primary Master Submenu
Default
[Auto]
---
---
■
A number between
0 and 65,535
–—
Description
Selects the ATA/ATAPI device type. Select Auto to have the type automatically identified by the BIOS at POST. If None is selected, all of the following Set-up items do not appear. Select CD-ROM if a
CD-ROM drive is installed at this connection. If Hard Disk is selected, you must specify the number of Cylinders, Heads, and Sectors for the drive.
Logical Block Addressing (LBA)
The total number of sectors on your hard disk
The maximum capacity of your hard disk
Cylinders/Heads/Sectors
This item is active only when Hard Disk is selected as the type. This field is changed by incrementing (pressing the [Spacebar]) or by typing in the number.
6
M a i n M e n u
Menu Field
Heads:
Sectors:
Options
■ A number between
1 and 16
Default
–—
■
A number between
0 and 63
–—
Maximum
Capacity:
■ Display only –—
Multi-Sector
Transfers:
LBA Mode Control:
■
■
■
■
■
Disabled
2 Sectors
4 Sectors
8 Sectors
16 Sectors
■
■
Disabled
Enabled
Transfer Mode:
Ultra DMA Mode:
■
■
■
■
■
■
■
Standard
Fast PIO 1
Fast PIO 2
Fast PIO 3
Fast PIO 4
Multiword DMA 1
Multiword DMA 2
■
■
■
■
■
■
■
Disabled
Mode 0
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
[16 Sectors]
[Enabled]
[Multiword
DMA 2]
[Disabled]
Description
This item is active only when Hard Disk is selected as type. You can change the value by incrementing (pressing the [Spacebar]) or by typing in the number.
This item is active only when Hard Disk is selected as type. You can change the value by incrementing (pressing the [Spacebar]) or by typing in the number.
Displays the maximum capacity of the drive calculated from the parameters of the hard disk when Auto is selected and the type is identified as hard disk.
This option cannot be changed when Auto is selected. Specify the number of sectors per block for multiple sector transfer.
Enables or disables logical Block Addressing in place of Cylinder,
Head, Sector addressing. This option cannot be changed when Auto is selected.
Selects the method for moving data to/from the drive. Autotype the drive to select the optimum transfer mode. This option cannot be changed when Auto is selected.
Selects the method for moving data to/from the drive. Autotype the drive to select the optimum transfer mode. This option cannot be changed when Auto is selected.
C A U T I O N
■ A bootable CD-ROM may have either a floppy disk or hard drive format. When the bootable CD-ROM is used, the drive allocations change automatically without changing the BIOS setup. If a floppy disk format CD-ROM is used, the
CD-ROM becomes Drive A. The CD-ROM will only take drive C: (hard drive format) if the internal hard drive is not present or is disabled. The bootable CD-ROM can never use a C: designation if a formatted internal hard drive is present since the C: designator is always reserved for the internal hard drive.The boot sequence ignores the new drive designations, however, your application software will use the new designations.
■
Be careful of the operating environment when booting from a CD-ROM or you may overwrite files by mistake.
7
L i f e B o o k S S e r i e s N o t e b o o k B I O S
Secondary Master Submenu of the Main Menu
The Secondary Master submenu is for the internal CD-
ROM drive. The drive type is displayed on this menu as well as the Main menu. Your notebook auto-senses the characteristics of the internal drive installed. You will not need to modify these settings; they are displayed for your reference.
Note that actual drive labels shown may vary.
PhoenixBIOS Setup Utility
Main
Secondary Master [CD-224E-(SM)] Item Specific Help
Type: [ Auto ]
Multi-Sector Transfers: [Disabled]
LBA Mode Control: [Disabled]
Transfer Mode:
Ultra DMA Mode:
[Standard]
[Disabled]
Select ATA/ATAPI drive installed here.
[Auto]
The BIOS auto-types the drive on boot time.
Except [Auto]
You enter parameters of the drive.
[None]
The drive is disabled.
F1 Help
ESC Exit
Select Item
Select Menu
-/Space
Enter
Change Values
Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
Figure 3. Secondary Master Submenu
Table 3: Fields, Options and Defaults for the Secondary Master Submenu of the Main Menu
Menu Field
Type:
Multi-Sector
Transfers:
LBA Mode
Control:
Options
■
■
■
■
Auto
None
CD-ROM
Hard Disk
■
■
■
■
■
Disabled
2 Sectors
4 Sectors
8 Sectors
16 Sectors
■
■
Disabled
Enabled
Default
[Auto]
[Disabled]
[Disabled]
Description
Selects the ATA/ATAPI device type. Select Auto to have the type automatically identified by the BIOS at POST. If None is selected, all of the following Set-up items do not appear. Select CD-ROM or Hard Disk for appropriate drive type installed at this connection.
This option cannot be changed when Auto is selected. Specify the number of sectors per block for multiple sector transfer.
Enables or disables Logical Block Addressing in place of Cylinder, Head,
Sector addressing. This option cannot be changed when Auto is selected.
8
M a i n M e n u
Table 3: Fields, Options and Defaults for the Secondary Master Submenu of the Main Menu
Menu Field
Transfer Mode:
Ultra DMA
Mode:
Options
■
■
■
■
■
■
■
Standard
Fast PIO 1
Fast PIO 2
Fast PIO 3
Fast PIO 4
Multiword DMA 1
Multiword DMA 2
■
■
■
■
■
■
■
Disabled
Mode 0
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Default
[Standard]
[Disabled]
Description
Selects the method for moving data to/from the drive. Autotype the drive to select the optimum transfer mode. This option cannot be changed when Auto is selected.
Selects the method for moving data to/from the drive. Autotype the drive to select the optimum transfer mode. This option cannot be changed when Auto is selected.
Exiting from Main Menu
When you have finished setting the parameters on this menu, you can either exit from the setup utility, or move to another menu. If you wish to exit from the setup utility, press the [Esc] key or use the cursor keys to go to the Exit menu or to move to another menu.
9
L i f e B o o k S S e r i e s N o t e b o o k B I O S
ADVANCED MENU – SETTING DEVICE FEATURE CONTROLS
The Advanced Menu allows you to:
■
Set the I/O addresses for the serial and parallel ports.
■
■
■
■
Set the features of the keyboard/mouse.
Select between the display panel and/or an external
CRT display.
Set internal device configurations
Configure USB features.
■
■
Configure miscellaneous features such as Wake Up On
LAN.
Configure DMI Event Logging.
Follow the instructions for Navigating Through the
Setup Utility to make any changes.
(See Navigating Through the Setup Utility on page 2 for
The following tables show the names of the menu fields for the Advanced Menu and its submenus, all of the options for each field, the default settings and a description of the field’s function, and any special information needed to help understand the field’s use.
PhoenixBIOS Setup Utility
Main Advanced Security Boot Info Exit
Serial/Parallel Port Configurations
Keyboard/Mouse Features
Video Features
Internal Device Configurations
CPU Features
USB Features
Miscellaneous Configurations
Event Logging
Item Specific Help
Configures serial ports and parallel ports
F1 Help
ESC Exit
Select Item
Select Menu
-/Space
Enter
Change Values
Select Sub-Menu
Figure 4. Advanced Menu
F9 Setup Defaults
F10 Save and Exit
10
A d v a n c e d M e n u
Table 4: Fields, Options and Defaults for the Advanced Menu
Menu Field
Serial/Parallel Port
Configurations
Keyboard/Mouse
Features
Video Features
Internal Device
Configurations
CPU Features
USB Features
Miscellaneous
Configurations
Event Logging
Description
When selected, opens the Serial/Parallel Port Configurations submenu which allows the user to modify settings for serial, infrared and parallel ports.
When selected, opens the Keyboard/Mouse Features submenu, which allows setting external and internal keyboard and mouse parameters.
When selected, opens the Video Features submenu, which allows setting of the display parameters, including routing of video signals to different displays.
When selected, opens the Internal Device Configuration submenu, which allows enabling or disabling the
IDE LAN, and modem controllers.
When selected, opens the CPU Features submenu, which allows the user to modify the Intel(R) Speed-
Step(R) features.
Configures USB features.
Configures miscellaneous features, such as Wake Up On LAN and Power Button.
When selected, opens the event logging submenu.
11
L i f e B o o k S S e r i e s N o t e b o o k B I O S
Serial/Parallel Port Configuration Submenu of the Advanced Menu
The Serial/Parallel Port Configuration submenu provides the ability to set the I/O addresses and interrupt levels for the serial, infrared, and parallel ports of your notebook.
P O I N T S
■ To prevent IRQ and address conflicts, avoid changing the default settings.
■
The BIOS will warn you of resource conflicts by placing a yellow asterisk next to each device that is in conflict.
C A U T I O N
I/O addresses, DMA channels, and Interrupt levels can be entered in various ways, including via the BIOS setup utility, the control software for the I/O device, or the hardware. If any two ports or devices, serial or parallel, have the same I/O address assigned your notebook will not function normally. Please keep a record of original settings before making any changes in the event that a restoration is required. See your hardware and software documentation as well as the setup utility to determine settings, limitations, etc.
■ All I/O addresses in Table 5 are in hexadecimal.
Advanced
PhoenixBIOS Setup Utility
Serial/Parallel Port Configurations
Serial Port:
I/O Address:
Interrupt:
Infrared Port:
Mode:
I/O Address:
Interrupt:
I/O Address:
DMA Channel:
Parallel Port:
Mode:
I/O Address:
Interrupt:
[ Enabled ]
[3F8-3FF]
[IRQ 4]
[Enabled]
[FIR]
[2E8 - 2EF]
[IRQ 3]
[400 - 43F]
[DMA 3]
[Enabled]
[Bi-directional]
[378-37F]
[IRQ 7]
Item Specific Help
[Disabled]
The port is disabled.
[Enabled]
The port is enabled with user configuration.
[Auto]
Plug & Play OS configure the port.
F1 Help
ESC Exit
Select Item
Select Menu
-/Space
Enter
Change Values
Select Sub-Menu
F9
F10
Figure 5. Serial/Parallel Port Configuration Submenu
Setup Defaults
Save and Exit
12
A d v a n c e d M e n u
Table 5: Fields, Options and Defaults for Serial/Parallel Port Configuration Submenu of Advanced Menu
Menu Field
Serial Port:
I/O Address:
Interrupt:
Infrared Port:
Mode:
I/O Address:
Interrupt:
I/O Address:
DMA Channel:
Parallel Port:
Mode:
I/O Address:
Interrupt:
■
■
IrDA
FIR
■
■
■
■
3F8 - 3FF
2F8 - 2FF
3E8 - 3EF
2E8 - 2EF
■
■
■
■
IRQ 3
IRQ 4
IRQ 10
IRQ 11
■
■
■
■
400 - 43F
480 - 4BF
500 - 53F
580 - 5BF
■
■
DMA 1
DMA 3
■
■
■
Disabled
Enabled
Auto
■
■
■
Output Only
Bi-directional
ECP
Options
■
■
■
Disabled
Enabled
Auto
■
■
■
■
3F8 - 3FF
2F8 - 2FF
3E8 - 3EF
2E8 - 2EF
■
■
■
■
IRQ 3
IRQ 4
IRQ 10
IRQ 11
■
■
■
Disabled
Enabled
Auto
■
■
■
378 - 37F
278 - 27F
3BC - 3BF
■
■
IRQ 5
IRQ 7
Default
[Enabled]
[3F8 - 3FF]
[IRQ 4]
[Enabled]
[FIR]
[2E8 - 2EF]
[IRQ 3]
[400 - 43F]
[DMA 3]
[Enabled]
[Bi-directional]
[378 - 37F]
[IRQ 7]
Description
Configures the serial port using either no configuration (Disabled), a user defined configuration (Enabled), or by allowing the BIOS or OS to choose the configuration (Auto).
Allows user to set the serial port base I/O address when serial port is
Enabled.
Allows user to set the serial port interrupt when serial port is Enabled.
Configures the infrared port using either no configuration (Disabled), a user defined configuration (Enabled), or by allowing the BIOS or OS to choose the configuration (Auto).
When the infrared port is enabled this option is available allowing the user to set the mode for the infrared port.
Allows user to set the infrared port I/O address when the infrared port is
Enabled.
Allows user to set the infrared port interrupt when the infrared port is
Enabled.
Allows the user to select the I/O address for Fast Infrared (FIR).
Allows user to set the infrared port DMA Channel when the infrared port is Enabled.
Configures the parallel port using either no configuration (Disabled), a user defined configuration (Enabled), or by allowing the BIOS or OS to choose the configuration (Auto).
When the parallel port is enabled this option is available allowing the user to set the mode for the parallel port. Bi-directional allows two-way transfer of information between your notebook and a parallel device.
Output Only (Half Duplex) allows information to be transferred in only one direction, from your notebook to the printer or similar device. ECP
Mode allows communication with the ECP class of parallel I/O devices.
Allows user to set the parallel port base I/O address when the parallel port is Enabled.
Allows user to set the parallel port interrupt when the parallel port is
Enabled.
13
L i f e B o o k S S e r i e s N o t e b o o k B I O S
Keyboard/Mouse Features Submenu of the Advanced Menu
The Keyboard/Mouse Features submenu is for setting the parameters of the integrated and external mouse and keyboard.
PhoenixBIOS Setup Utility
Advanced Security Power Savings Exit
Keyboard/Mouse Features Item Specific Help
Numlock:
Hot Plug:
Internal Pointing Device:
Initialization on Resume:
[ Auto ]
[Enabled]
[Auto Disabled]
[Fast]
Selects power-on state for Numlock.
F1 Help
ESC Exit
Select Item
Select Menu
-/Space
Enter
Change Values
Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
Figure 6. Keyboard/Mouse Features Submenu
Table 6: Fields, Options and Defaults for the Keyboard/Mouse Submenu of the Advanced Menu
Menu Field
Numlock:
Hot Plug:
Internal Pointing
Device:
Initialization on
Resume:
Options
■
■
■
■
Auto
On
Off
On/Padlock Off
■
■
Disabled
Enabled
■
■
■
■
Auto Disabled
Manual Setting
Always Enabled
Always Disabled
■
■
Fast
Normal
Default
[Auto]
[Enabled]
[Auto Disabled]
[Fast]
Description
Sets the NumLock function state when the computer completes booting.
Enables and disables the ability to plug a mouse or keyboard into the PS/2 port and have it immediately recognized and active.
Sets the device controlling the mouse cursor on the screen.
Always Enabled makes the pointing device always enabled whether there is an external mouse or not. Always Disabled makes the pointing device always disabled. Auto Disabled disables the internal pointing device when an external pointing device is connected to the PS/2 port. Manual Setting allows the device to be enabled or disabled using a Hot Key.
When Fast is selected, initialization for the external PS/2 devices is optimized to speed up on Resume. When Normal is selected, initialization is not optimized.
14
A d v a n c e d M e n u
Video Features Submenu of the Advanced Menu
The Video Features Submenu is for setting the display parameters.
PhoenixBIOS Setup Utility
Main Advanced Security Power Savings Exit
Video Features Item Specific Help
Display: [Auto] ]
Compensation: [Enabled]
Select display terminal.
F1 Help
ESC Exit
Select Item
Select Menu
-/Space
Enter
Change Values
Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
Figure 7. Video Features Submenu
Table 7: Fields, Options and Defaults for the Video Features Submenu of the Advanced Menu
Menu Field
Display:
Compensation:
Options
■
■
■
Internal Flat Panel
External
Auto
■
■
Disabled
Enabled
Default
[Auto]
[Enabled]
Description
Selects where the video signal will be routed.
Enables or disables display compensation. Display compensation is used to match the native resolution of the display with the input. For example, if you are using an application whose resolution causes it to appear smaller than the screen, enabling Compensation will expand the image to fill the screen.
15
L i f e B o o k S S e r i e s N o t e b o o k B I O S
Internal Device Configurations Submenu of the Advanced Menu
The Internal Device Configuration submenu allows the user to configure other internal devices.
PhoenixBIOS Setup Utility
Main Advanced Security Power Savings Exit
Internal Device Configurations
IDE Contoller:
Modem Controller:
LAN Controller:
[ Both
[Enabled]
[Auto]
Item Specific Help
[Disabled]
No IDE ports are enabled.
[Primary]
Only primary IDE port is enabled.
[Secondary]
Only secondary IDE port is enabled.
[Both]
Both primary and secondary IDE ports are enabled.
F1 Help
ESC Exit
Select Item
Select Menu
-/Space
Enter
Change Values
Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
Figure 8. Internal Device Configuration Submenu
Table 8: Fields, Options and Defaults for the Internal Device Configuration Submenu of the Advanced Menu
Menu Field
IDE Controller:
Modem Controller:
LAN Controller:
Options
■
■
■
■
Disabled
Primary
Secondary
Both
■
■
Disabled
Enabled
■
■
■
Disabled
Enabled
Auto
Default
[Both]
[Enabled]
[Auto]
Description
Enables or disables selected IDE devices.
Enables or disables the modem device.
Enables or disables the LAN controller.When Auto is selected, the
LAN will be disabled when the system is running on battery power and the LAN cable is not connected.
16
A d v a n c e d M e n u
CPU Features Submenu of the Advanced Menu
The CPU Features Submenu allows the user to modify the Intel(R) SpeedStep(R) Technology features.
PhoenixBIOS Setup Utility
Main Advanced Security Power Savings Exit
CPU Features
Item Specific Help
SpeedStep(R) Technology: [Enabled]
On Battery: [Battery Optimized]
On AC: [Maximum Performance]
Select Enhanced
Intel(R) SpeedStep(R)
Technology enabled or disabled.
F1 Help
ESC Exit
Select Item
Select Menu
-/Space
Enter
Change Values
Select Sub-Menu
F9 Setup
F10 Save and Exit
Figure 9. CPU Features Submenu
Table 9: Fields, Options and Defaults for the CPU Features Submenu of the Advanced Menu
Menu Field
SpeedStep(R)
Technology:
Options
■
■
Disabled
Enabled
Default
[Enabled]
Description
Enables or disables SpeedStep(R) Technology which allows the user to determine the CPU performance when the notebook is running on AC or battery. This technology decreases power consumption by decreasing CPU speeds.
On Battery:
On AC:
■
■
■
Maximum
Performance
Battery
Optimized
Automatic
■
■
■
Maximum
Performance
Battery
Optimized
Automatic
[Battery Optimized]
[Maximum
Performance]
Allows the user to select the CPU performance when the system is running on battery power.
Allows the user to select the CPU performance when the system is running on AC power.
17
L i f e B o o k S S e r i e s N o t e b o o k B I O S
USB Features Submenu of the Advanced Menu
The USB Features Submenu configures the USB features for your system.
PhoenixBIOS Setup Utility
Main Advanced Security Power Savings Exit
USB Features Item Specific Help
Legacy USB Support:
[Enabled]
SCSI SubClass Support: [Disabled]
[Disabled]
The feature is disabled.
[Enabled]
Legacy Floppy Emulation is enabled and USB floppy is available without USB aware OS.
F1 Help
ESC Exit
Select Item
Select Menu
-/Space
Enter
Change Values
Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
Figure 10. USB Features Submenu
Table 10: Fields, Options and Defaults for the ACPI Features Submenu of the Advanced Menu
Menu Field
Legacy USB
Support:
SCSI SubClass
Support:
Options
■
■
Disabled
Enabled
■
■
Disabled
Enabled
Default
[Enabled]
[Disabled]
Description
When Disabled is selected, legacy USB emulation is disabled. When
Enabled is selected, legacy USB emulation is enabled and USB devices are available without USB-aware OS.
When Enabled is selected, USB devices that belong to the SCSI subclass in the mass storage class (e.g., USB Memory Key) are enabled.
18
A d v a n c e d M e n u
Miscellaneous Configurations Submenu of the Advanced Menu
The Miscellaneous Configurations Submenu configures miscellaneous features for your system.
PhoenixBIOS Setup Utility
Main Advanced Security Power Savings Exit
Miscellaneous Configurations
Item Specific Help
Power Button:
Wake up on LAN:
Volume Setting:
[ Disabled ]
[Disabled]
[Middle]
Configures the power button.
*ACPI OS ignores this setting.
F1 Help
ESC Exit
Select Item
Select Menu
-/Space
Enter
Change Values
Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
Figure 11. Miscellaneous Configurations Submenu
Table 11: Fields, Options and Defaults for the Miscellaneous Configurations Submenu
Menu Field
Power Button:
Wake up on LAN:
Volume Setting:
Options
■
■
Disabled
Power Off
■
■
Disabled
Enabled
■
■
■
■
Off
Minimum
Middle
Maximum
Default
[DIsabled]
[Disabled]
[Middle]
Description
When Disabled is selected, the power button does not respond to a press. When Power Off is selected, the button turns the power off.
When Enabled is selected, the system will wake up when the internal
LAN device receives a Magic Packet while the system is powered off.
Allows you to set or disable the system volume level.
19
L i f e B o o k S S e r i e s N o t e b o o k B I O S
Event Logging Submenu of the Advanced Menu
The Event Logging Submenu configures event logging features for DMI events.
PhoenixBIOS Setup Utility
Main Advanced Security Power Savings Exit
Event Logging Item Specific Help
Event Log Capacity: Space Available
Event Log Validity: Valid
View Event Log: [Enter]
Event Logging: [Enabled]
System Boot Event: [Disabled]
Clear All Event Logs: [No]
Mark Events as Read: [Enter]
Press <Enter> key to view the contents of the event log.
F1 Help
ESC Exit
Select Item
Select Menu
-/Space
Enter
Change Values
Select Sub-Menu
Figure 12. Event Logging Submenu
F9 Setup Defaults
F10 Save and Exit
Table 12: Fields, Options and Defaults for the Event Logging Submenu of the Advanced Menu
Options Default
Space Available
Description
Display only.
Menu Field
Event Log
Capacity:
Event Log Validity:
View Event Log:
Event Logging:
System Boot
Event:
Clear All Event
Logs:
Mark Events as
Read:
■
Enter
■
■
Disabled
Enabled
■
■
Disabled
Enabled
■
■
No
Yes
■
Enter
Valid
[Enter]
[Enabled]
[Disabled]
[No]
[Enter]
Display only.
Allows you to view content of event log.
Turns event logging on and off for all DMI events.
Turns event logging on and off for DMI system boot events.
When set to [Yes] all event logs will be cleared at next boot.
Allows you to make all events currently in the event log as read.
20
S e c u r i t y M e n u
SECURITY MENU – SETTING THE SECURITY FEATURES
The Security menu allows you to set up the data security features of your notebook to fit your operating needs and to view the current data security configuration. Follow the instructions for Navigating Through the Setup Utility to
make any changes. (See Navigating Through the Setup
Utility on page 2 for more information)
The following tables show the names of the menu fields for the Security menu and its submenus, the options for each field, the default settings and a description of the field's function and any special information needed to help understand the field's use. The default condition is no passwords required and no write protection.
P O I N T
■ If you set a password, write it down and keep it in a safe place. If you forget the password you will have to contact your support representative to regain access to your secured functions and data.
■
If you make an error when re-entering the password a [Warning] will be displayed on the screen. To try again press the [Enter] key and then retype the password. Press the [Esc] key to abort the password setting process.
■ If the Password on Boot is Disabled you will not have to type your password upon resuming the system from the Suspend or Save-to-Disk modes.
C A U T I O N
Entering a password incorrectly three times in a row will cause the keyboard and mouse to be locked out and the warning [System Disabled] to be displayed. If this happens, restart the computer by turning off and on the power with the power switch and use the correct password on reboot.
PhoenixBIOS Setup Utility
Main Advanced Security Boot Info Exit
Supervisor Password Is:
User Password Is:
Set Supervisor Password
Set User Password
[ Enter ]
[Enter]
Minimum User Password Length: [0]
Password on Boot:
On Automatic Wake up:
KB Lock on Resume:
Boot from Removable Media:
Hard Disk Security
Owner Information
Security Panel On Resume:
Clear
Clear
[Disabled]
[Disabled]
[Disabled]
[All]
[Enabled]
Item Specific Help
Press <Enter> key to set Supervisor Password to enable any password features.
Then password entry is required to enter BIOS
Setup.
F1 Help
ESC Exit
Select Item
Select Menu
-/Space
Enter
Change Values
Select Sub-Menu
Figure 13. Security Menu
F9 Setup Defaults
F10 Save and Exit
21
L i f e B o o k S S e r i e s N o t e b o o k B I O S
Table 13: Fields, Options and Defaults for the Security Menu
Menu Field
Supervisor
Password is:
User Password is:
Set Supervisor
Password
Set User Password
Options
–—
–—
[Enter]
[Enter]
[0]
Default
Clear
Clear
[Enter]
[Enter]
[0]
Description
A display-only field. Set is displayed when the system Supervisor
Password is set and Clear when it is not.
A display-only field. Set is displayed when the general User Password is set, and Clear when it is not.
Sets, changes or cancels Supervisor Password. The Supervisor Password may be up to eight characters long and include only letters or numbers
(no symbols). Passwords are NOT case- sensitive. To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Re-enter New Password field. When a Supervisor
Password is set it must be used to access the BIOS setup utility.
This field can only be accessed if the Supervisor Password is set. Sets, changes or cancels the User Password. The User Password may be up to eight characters long and must include only letters or numbers (no symbols). Passwords are NOT case-sensitive. To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Re-enter New Password field. When a User Password is set it must be used to access the BIOS setup utility.
Sets the minimum length for User Password.
Minimum User
Password Length:
Password on Boot: [Disabled]
On Automatic
Wake up:
KB Lock on
Resume:
Boot from
Removable Media:
■
■
■
Disabled
First Boot
Every Boot
■
■
Disabled
Enabled
■
■
Disabled
Enabled
[Disabled]
[Disabled]
[All]
When Enabled, a password (User or Supervisor) is required after the
Power On Self Test (POST) before the operating system will be read from a disk. When set to Disabled no password is required. If no Supervisor
Password is set this feature is not available and no password is required.
This field is active only when Password On Boot is set to First Boot or
Every Boot. When disabled, password entry is not required on automatic wake up on LAN or Real Time Clock. When enabled, the password is still required on automatic wake up.
When set to Enabled, the PS/2 keyboard and mouse inputs are locked out upon Suspend from Resume or Save-to-Disk mode until the password is entered. When both passwords are set, the User password is always used to lock. Password entry before OS boot is disabled upon unattended boot.
Enable password allows supervisor access only.
Hard Disk Security:
Owner
Information:
Security Panel On
Resume
■
■
All
Supervisor only
–—
–—
■
■
Disabled
Enabled
–—
–—
[Enabled]
Configures hard disk security features.
Sets Owner information.
Allows the Security Panel Feature to be enabled or disabled upon
Suspend from Resume.
22
S e c u r i t y M e n u
Hard Disk Security Submenu of the Security Menu
The Hard Disk Security Submenu is for configuring hard disk security features.
PhoenixBIOS Setup Utility
Main Advanced Security Power Savings Exit
Hard Disk Security Item Specific Help
Primary Master Password Is:
Secondary Master Password Is:
Set Primary Master Password
Set Secondary Master Password
Clear
Not Available
[Enter]
[Enter]
F1 Help
ESC Exit
Select Item
Select Menu
-/Space
Enter
Change Values
Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
Figure 14. Hard Disk Security Submenu
Table 14: Fields, Options and Defaults for the Hard Disk Security Submenu of the Security Menu
Menu Field
Primary Master
Password Is:
Secondary Master
Password Is:
Set Primary
Master Password
Set Secondary
Master Password
Default
---
---
[Enter]
[Enter]
Description
A display-only field. Set is displayed when the Master Password is set and Clear when it is not.
A display-only field. Not Available is displayed.
Sets, changes or cancels Primary Master Password. The Primary Master Password may be up to seven characters long and include only letters or numbers (no symbols). Passwords are
NOT case- sensitive. To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Re-enter New Password field. When a Primary
Master Password is set it must be used to access the hard disk. Data on the hard disk cannot be read on other systems.
Not currently available.
23
L i f e B o o k S S e r i e s N o t e b o o k B I O S
Owner Information Submenu of the Security Menu
The Owner Information Submenu is for setting owner information. Note that Owner Information cannot be set without having entered a supervisor’s password.
PhoenixBIOS Setup Utility
Main Advanced Security Power Savings Exit
Owner Information Item Specific Help
Owner Information Is: Clear
Set Owner Information [Enter]
Foreground Color:
Background Color:
[Gray]
[Black]
Press <Enter> key to set owner information.
Up to 80 characters can be set. Available characters are ASCII codes from 32 through
126.
The owner information is always displayed at the bottom line of the screen during POST.
F1 Help
ESC Exit
Select Item
Select Menu
-/Space
Enter
Change Values
Select Sub-Menu
Figure 15. Owner Information Submenu
F9 Setup Defaults
F10 Save and Exit
Table 15: Fields, Options and Defaults for the Owner Information Submenu of the Security Menu
Menu Field
Owner
Information Is:
Set Owner
Information:
Foreground
Color:
Background
Color:
Options
–—
–—
■
■
■
■
Black
Blue
Green
Cyan
■
■
■
■
Black
Blue
Green
Cyan
■
■
■
■
Red
Magenta
Brown
White
■
■
■
■
Red
Magenta
Brown
White
■
■
■
■
Gray
Light Blue
Light Green
Light Cyan
■
■
■
■
Gray
Light Blue
Light Green
Light Cyan
■
■
■
■
Light Red
Light Magenta
Yellow
Bright White
■
■
■
■
Light Red
Light Magenta
Yellow
Bright White
Default
Clear
[Enter]
[Gray]
[Black]
Description
Display only.
Field to write owner information (e.g., your name).
Set foreground color.
Sets background color.
Exiting from the Security Menu
When you have finished setting the parameters on the Security Menu, you can either exit from setup utility or move to another menu. If you wish to exit from setup utility, press the [Esc] key to go to the Exit Menu. If you wish to move to another menu, use the cursor keys.
24
B o o t M e n u
BOOT MENU – SELECTING THE OPERATING SYSTEM SOURCE
The Boot Menu is used to select the order in which the
BIOS searches sources for the operating system. Follow the instructions for Navigating Through the Setup
Utility to make any changes. (See Navigating Through the
Setup Utility on page 2 for more information)
The following tables show the names of the menu fields for the Boot menu and its submenu, all of the options for each field, the default settings and a description of the field's function and any special information needed to help understand the field's use.
PhoenixBIOS Setup Utility
Main Advanced Security Boot Info Exit
Item Specific Help
Quick Boot:
Boot Time Diagnostic Screen:
[Enabled]
[Disabled]
Preboot Execution Environment: [Disabled]
Boot Device Priority
[Disabled]
All diagnostic tests will be done.
[Enabled]
Some diagnostic tests may be skipped while booting to speed up.
F1 Help
ESC Exit
Select Item
Select Menu
-/Space
Enter
Change Values
Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
Figure 16. Boot Menu
Table 16: Fields, Options and Defaults for the Boot Menu
Menu Field
Quick Boot:
Boot Time
Diagnostic Screen:
Preboot Execution
Environment:
Boot Device
Priority:
Options
■
■
Disabled
Enabled
■
■
Disabled
Enabled
■
■
Disabled
Enabled
Selects the Boot
Device Priority submenu
Default
[Enabled]
[Disabled]
[Disabled]
__
Description
Turns on and off booting with a truncated set of Power On Self
Tests. (Fewer tests mean faster turn on.)
Turns on and off display of test results instead of Fujitsu logo screen during Power On Self Test.
Turns on and off boot from network server options.
This menu allows setting up the source for the operating system.
See “Boot Device Priority Submenu” in the following section.
25
L i f e B o o k S S e r i e s N o t e b o o k B I O S
The Boot Device Priority Submenu of the Boot Menu
The Boot Device Priority Submenu is for setting the order of checking of sources for the operating system.
C A U T I O N
Be aware of the operating environment when booting from a CD-ROM or you may overwrite files by mistake.
PhoenixBIOS Setup Utility
Main Advanced Security Power Savings Boot
Boot Device Priority Item Specific Help
+Floppy Disk Drive
+Hard Disk Drive
CD-ROM Drive
Keys used to view or configure devices:
<Enter> expands or collapses devices with a + or -.
<Ctrl+Enter> expands all.
<Shift+1> enables or disables a device.
<+>/<Space> or <-> moves the device up or down.
<d> removes a device that is not installed.
F1 Help
ESC Exit
Menu Field
+Floppy Disk Drive
+Hard Disk Drive
CD-ROM Drive
Select Item
Select Menu
-/Space
Enter
Change Values
Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
Figure 17. Boot Device Priority Submenu
Table 17: Fields, Options and Defaults for the Boot Device Priority Submenu of the Boot Menu
Description
The boot selections determine the order in which the BIOS searches for the operating system during a startup sequence. To change the order highlight one source by using the [up] or [down] cursor keys and then press the
[+] or [-] key to change the order number for that source. Be sure to save your changed order when you exit the
BIOS setup utility.
Exiting from Boot Menu
When you have finished setting the boot parameters with the Boot menu, you can either exit from the setup utility or move to another menu. If you wish to exit from the setup utility press the [Esc] key to go to the Exit menu. If you wish to move to another menu, use the cursor keys.
26
I n f o M e n u
INFO MENU – DISPLAYS BASIC SYSTEM INFORMATION
The Info menu is a display only screens that provides the configuration information for your notebook.
The following table shows the names of the menu fields for the Info menu and the information displayed in those fields. These fields are for information purposes only, and are not editable.
P O I N T
The information, including CPU type and speed, and total memory, displayed on this screen varies according to the unit you purchased.
PhoenixBIOS Setup Utility
Main Advanced Security Boot Info Exit
Item Specific Help
BIOS Version: 1.03
BIOS Date: 03/31/2003
BIOS Area: E000h - FFFFh
CPU Type:
CPU Speed:
L1 Cache:
L2 Cache:
Intel(R) Pentium(R) M
1.60 GHz
64 KB
1024 KB
Total Memory: 256 MB
Memory Slot 1: None
Memory Slot 2: 256 MB DDR SDRAM
F1 Help
ESC Exit
Select Item
Select Menu
-/Space Change Values
Enter Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
Figure 18. Info Menu
Table 18: Fields, Options and Defaults for the Info Menu
Note that the parameters listed in the following table may be different, depending upon your system configuration.
Menu Field
BIOS Version:
BIOS Date:
BIOS Area:
CPU Type:
L1 Cache:
Default
1.03
03/31/2003
E000h – FFFFh
Intel(R) Pentium(R) M
64 KB
Menu Field
L2 Cache:
Total Memory:
Memory Slot 1:
Memory Slot 2:
Default
1024 KB
256 MB
None
256 MB DDR SDRAM
27
L i f e B o o k S S e r i e s N o t e b o o k B I O S
EXIT MENU – LEAVING THE SETUP UTILITY
The Exit Menu is used to leave the setup utility. Follow the instructions for Navigating Through the Setup Utility to
shows the names of the menu fields for the Exit menu, the default settings and a description of the field's function and any special information needed to help understand the field's use.
PhoenixBIOS Setup Utility
Main Advanced Security Boot Exit
Item Specific Help
Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes
Exit System Setup and save your changes to
CMOS.
F1 Help
ESC Exit
Select Item
Select Menu
-/Space Change Values
Enter Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
Figure 19. Exit Menu
Table 19: Fields, Options and Defaults for the Exit Menu
Menu Field
Exit Saving
Changes
Exit Discarding
Changes
Load Setup
Defaults
Discard Changes
Save Changes
Description
Exit Saving Changes and Exit will store all the entries on every menu of the setup utility to the BIOS memory and then exit the setup utility. A confirmation message Save Configuration changes and exit now? [Yes]
[No] will be displayed.
Selecting Exit Discarding Changes and Exit will exit the setup utility with out writing to the BIOS memory. When the
BIOS recognizes this selection it will load the operating system and begin operation.
Selecting Load Setup Defaults will load the factory preset default values for all menu fields, then display the message
Load default configuration now? [Yes] [No].
When confirmed the setup utility will return to the Exit
Menu. To return to another menu follow the directions in the Navigating Through the Setup Utility Section.
Selecting Discard Changes will load the previous values in BIOS memory for all menu fields. The message Load previous now? [Yes] [No] will be displayed. When confirmed the utility will return to the Exit menu. To return to another menu, follow the directions in the Navigating Through the Setup Utility Section.
Selecting Save Changes causes the new settings in all menus to be written to the BIOS memory. The message Save configuration changes now? [Yes] [No] will be displayed. When confirmed, the setup utility will return to the Exit menu. To go to another menu, follow the directions in the Navigating Through the Setup Utility section.
28
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project