Audio System
TOYOTA PART NO.
PT546-00130
Owner’s Manual
for AM/FM/HD Radio Broadcast/CD Player with iPod/
USB control/Bluetooth Audio
Alteration or modifications
carried out without appropriate
authorization may invalidate
the user’s right to operate the
equipment.
FCC ID : AJDK036
MODEL NO. : DEH-8228ZT
IC : 775E-K036
This device complies with
Part 15 of the FCC Rules and
Industry Canada licence-exempt
RSS standard(s). Operation is
subject to the following two
conditions: (1) this device may
not cause harmful interference,
and (2) this device must accept
any interference, including
interference that may cause
undesired operation of this device.
Information to User
Alteration or modifications
carried out without appropriate
authorization may invalidate
the user's right to operate the
equipment.
This transmitter must not
be co-located or operated in
conjunction with any other
antenna or transmitter.
2
<CRB3881-B/U>2
The antenna for Bluetooth
cannot be removed (or
replaced) by user.
This equipment complies with
FCC/IC radiation exposure limits
set forth for an uncontrolled
environment and meets the FCC
radio frequency (RF) Exposure
Guidelines in Supplement C to
OET65 and RSS-102 of the IC
radio frequency (RF) Exposure
rules. This equipment has
very low levels of RF energy
that it deemed to comply
without maximum permissive
exposure evaluation (MPE). But
it is desirable that it should be
installed and operated keeping
the radiator at least 20cm or
more away from person's body
(excluding extremities: hands,
wrists, feet and ankles).
This equipment has been tested
and found to comply with the
limits for a Class B digital device,
pursuant to Part 15 of the FCC
Rules. These limits are designed
to provide reasonable protection
against harmful interference in a
residential installation.
This equipment generates, uses
and can radiate radio frequency
energy and, if not installed
and used in accordance with
the instructions, may cause
harmful interference to radio
communications. However,
there is no guarantee that
interference will not occur
in a particular installation. If
this equipment does cause
harmful interference to radio or
television reception, which can
be determined by turning the
equipment off and on, the user
is encouraged to try to correct
the interference by one or more
of the following measures:
- Reorient or relocate the
receiving antenna.
- Increase the separation
between the equipment and
receiver.
- Connect the equipment into
an outlet on a circuit different
from that to which the receiver
is connected.
- Consult the dealer or an
experienced radio/TV
technician for help.
WARNING
Handling the cord on this
product or cords associated
with accessories sold with
the product may expose
you to chemicals listed on
proposition 65 known to the
State of California and other
governmental entities to cause
cancer and birth defect or other
reproductive harm.
Wash hands after handling.
USE OF CONTROL OR ADJUSTMENT OR PERFORMANCE OF
PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT
WILL INCREASE EYE HAZARD.
Features
CD playback
Music CD/CD-R/CD-RW playback is
possible.
MP3 file playback
You can play back MP3 files
recorded on CD-ROM/CD-R/CD-RW
(ISO9660 Level 1/Level 2 standard
recordings) or USB portable audio
player/USB memory.
• Supply of this product only conveys a license for private, noncommercial use and does not
convey a license nor imply any
right to use this product in any
commercial (i.e. revenue-generating) real-time broadcasting
(terrestrial, satellite, cable and/or
any other media), broadcasting/
streaming via internet, intranets
and/or other networks or in other
electronic content distribution
systems, such as pay-audio or
audio-on-demand applications.
An independent license for such
use is required. For details,
please visit
http://www.mp3licensing.com.
WMA file playback
You can play back WMA files
recorded on CD-ROM/CD-R/CD-RW
(ISO9660 Level 1/Level 2 standard
recordings) or USB portable audio
player/USB memory.
AAC file playback
You can play back AAC files
recorded on CD-ROM/CD-R/CD-RW
(ISO9660 Level 1/Level 2 standard
recordings) or USB portable audio
player/USB memory.
iPod compatibility
When you use this unit, you can
control an iPod, iPod classic, iPod
nano, iPod touch, iPhone. (Refer to
page 25.)
About WMA
Windows Media is either a registered trademark or trademark of
Microsoft Corporation in the United
States and/or other countries.
This product includes technology
owned by Microsoft Corporation
and cannot be used or distributed
without a license from Microsoft
Licensing, Inc.
3
<CRB3881-B/U>3
NOTICE
This unit may not operate
correctly depending on the
application used to encode
WMA files.
• Apple is not responsible for
the operation of this device or
its compliance with safety and
regulatory standards.
About HD Radio™
Technology
About iPod
• Reproducing and playing back
non-copyrighted material and
material that can legally be
reproduced and played back for
private use is permitted with the
iPod. Infringement of copyright is
legally prohibited.
• iPhone, iPod, iPod classic,
iPod nano, and iPod touch are
trademarks of Apple Inc., registered
in the U.S. and other countries.
• “Made for iPod” and “Made for
iPhone” mean that an electronic
accessory has been designed
to connect specifically to iPod
or iPhone, respectively, and has
been certified by the developer
to meet Apple performance
standards. Please note that the
use of this accessory with iPod
or iPhone may affect wireless
performance.
4
<CRB3881-B/U>4
• In this manual, iPod and iPhone
will be referred to as iPod.
About XM radio
HD Radio Technology manufactured under license from iBiquity Digital Corporation. U.S. and
Foreign Patents. HD RadioTM and
the HD, HD Radio, and “Arc” logos
are proprietary trademarks of iBiquity Digital Corp.
About Bluetooth
XM, SIRIUS and all related marks
and logos are trademarks of Sirius
XM Radio Inc. and its subsidiaries.
All rights reserved. Service not
available in Alaska and Hawaii.
The Bluetooth ® word mark and
logos are registered trademarks
owned by Bluetooth SIG, Inc. and
any use of such marks by Pioneer
Corporation is under license. Other
trademarks and trade names are
those of their respective owners.
Important information
about this manual
To ensure the correct
audio system operation
For safety reasons, this manual
indicates items requiring particular
attention with the following marks.
• Do not allow this unit to come
into contact with liquids.
Electrical shock could result.
Also, this unit damage, smoke,
and overheat could result from
contact with liquids.
• Do not put anything other than a
Compact Disc into the slot.
• The use of cellular phones inside
or near the vehicle may cause
noise from the audio system
speakers you are listening to.
However, this does not indicate a
malfunction.
NOTICE
This is a warning against
anything which may cause
damage to the vehicle or its
equipment if the warning is
ignored. You are informed about
what you must or must not do
in order to avoid or reduce the
risk of damage to your vehicle
and its equipment.
CAUTION
This is a warning against anything which may cause injury to
people if the warning is ignored.
You are informed about what
you must or must not do in
order to reduce the risk of injury
to yourself and others.
The Safety of Your
Ears is in Your Hands
Get the most out of your equipment by playing it at a safe level—a
level that lets the sound come
through clearly without annoying
blaring or distortion and, most
importantly, without affecting your
sensitive hearing. Sound can be
deceiving. Over time, your hearing
“comfort level” adapts to higher
volumes of sound, so what sounds
“normal” can actually be loud and
harmful to your hearing. Guard
against this by setting your equipment at a safe level BEFORE your
hearing adapts.
ESTABLISH A SAFE LEVEL:
• Set your volume control at a low
setting.
• Slowly increase the sound until
you can hear it comfortably and
clearly, without distortion.
• Once you have established a
comfortable sound level, set the
dial and leave it there.
BE SURE TO OBSERVE THE
FOLLOWING GUIDELINES:
• Do not turn up the volume so
high that you can’t hear what’s
around you.
• Use caution or temporarily
discontinue use in potentially
hazardous situations.
• Do not use headphones while
operating a motorized vehicle;
the use of headphones may
create a traffic hazard and is
illegal in many areas.
5
<CRB3881-B/U>5
Contents
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
About WMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
About iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
About XM radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
About HD RadioTM Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
About Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Important information about this manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
To ensure the correct audio system operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
The Safety of Your Ears is in Your Hands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Main Displays and Possible Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Basic Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-14
Listening to the RADIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-17
Listening to the HD Radio broadcast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-19
Listening to a CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21
Listening to MP3/WMA/AAC DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-24
About handling the iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-25
Connecting the iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-26
Disconnecting the iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Listening to songs on the iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-29
ABC SEARCH on an iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
About handling the USB portable audio player/USB memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Connecting the USB portable audio player/USB memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Listening to USB portable audio player/USB memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
How to subscribe to XM Satellite Radio <Option>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Display the RADIO ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35-36
Listening to a XM Satellite Radio broadcast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-39
Using the AUX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-41
Bluetooth Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-44
Listening to Bluetooth Audio player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-47
Phone Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-51
Using Hands-Free Phoning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-53
Making a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Changing the Opening Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54-55
Initial Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Connecting an external amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Using the Steering Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57-58
MP3, WMA and AAC files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
MP3 additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
WMA additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
AAC additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
About folders and MP3/WMA/AAC files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
USB portable audio player/ USB memory compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
CD player and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
CD-R and CD-RW discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
DualDiscs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Error indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-67
Changing or disconnecting your battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
6
<CRB3881-B/U>6
Main Displays and Possible Operations
Turn the MULTI KNOB to the right or left to
adjust the volume level, select a menu or select
an item from a list. Press the MULTI KNOB in the
center to set a selecting an item.
Possible operations are indicated.
MULTI
KNOB
UP
LEFT
RIGHT
The following are the main displays that appear during
UP/DOWN/RIGHT/LEFT and MULTI KNOB operation. Each
display indicates the operations that are currently available.
DOWN
You can select the next or the previous track
on a CD or iPod by pressing the RIGHT/LEFT.
or
You can select a setting option, etc. by
pressing the UP/DOWN/RIGHT/LEFT or
UP/DOWN.
You can select the next or the previous track or select a
folder on a CD , in a USB memory or Bluetooth audio
player by pressing the UP/DOWN/RIGHT/LEFT.
You can select a setting option, etc. by
pressing the center of the MULTI KNOB.
You can tune or seek a radio frequency by
pressing the UP/DOWN/RIGHT/LEFT.
You can navigate a list or edit the OPENING
TITLE by pressing the MULTI KNOB in the
center or the UP/DOWN/RIGHT/LEFT.
You can tune the Satellite Radio broadcasting
frequency or display and switch the category
by pressing the UP/DOWN/RIGHT/LEFT.
7
<CRB3881-B/U>7
Basic Operation
Your audio system works when the
ignition switch is in the “ACC” or
“ON” position.
NOTICE
To avoid draining the battery,
do not leave the car audio on
longer than necessary when the
engine is not running.
1 POWER
Press to turn the unit on or off.
2 MULTI KNOB/VOLUME
Turn the MULTI KNOB to raise/lower
the volume levels (total volume step
is 64). MULTI KNOB operation varies
depending on the audio source or
Menu. (Refer to page 7.)
To select the following setting
options, press the MULTI KNOB to
switch to the AUDIO MENU. Turn
the MULTI KNOB clockwise or counterclockwise to select an item and
press the MULTI KNOB. You can
select SETTINGS in TUNER mode or
iPod mode.
SSP  AUDIO CTRL  SETTINGS 
BLUETOOTH  PHONE
8
<CRB3881-B/U>8
• SSP (Scion Sound Processing)
SSP is a modified DSP (Digital Signal
Processing) system that provides a
customized sound for your vehicle.
Press the MULTI KNOB to display
the current SSP mode setting.
While the setting is displayed, press
repeatedly to switch to the following
modes.
NATURAL: Natural and smooth sound
that gives no listening
fatigue but comfort.
A powerful, energetic, live
HEAR:
sound.
Reproduces the sound on
FEEL:
the stage that musicians
hear.
For more details, please visit the SCION
website at
http://www.scion.com/.
HOW TO CHANGE THE EQ / SCION SOUND
PROCESSING (SSP) MODE
1 Press MULTI KNOB to
display the menu.
2 Turn MULTI KNOB to select
SSP.
3 Press MULT KNOB to enter
SSP.
4 Press MULTI KNOB to
select a sound mode.
*NATURAL  HEAR  FEEL
 NATURAL
5 Press ESC button to exit
SSP.
9
<CRB3881-B/U>9
• AUDIO CTRL
When the MULTI KNOB is turned,
the setting item of the AUDIO CTRL
menu will switch in the following
order:
FADER  BALANCE  BASS  TREBLE 
ASL (Automatic Sound Levelizer)  SUB-W
(Subwoofer)  ASR (Sound Retriever)
FADER: Use fader to adjust the sound balance
between the rear and front speakers.
The display ranges from R7 to F7.
HOW TO CHANGE THE FADER SETTING
4 Turn MULTI KNOB to select
FADER.
5 Press MULTI KNOB to enter
FADER.
6 Turn MULTI KNOB to adjust
the FADER.
1 Press MULTI KNOB to
display the menu.
BALANCE:
Use balance to adjust the sound balance between the left and right speakers. The display ranges from L7 to R7.
HOW TO CHANGE THE BALANCE SETTING
3 Press MULTI KNOB to enter
AUDIO CTRL.
10
<CRB3881-B/U>10
3 Press MULTI KNOB to enter
AUDIO CTRL.
4 Turn MULTI KNOB to select
BALANCE.
5 Press MULTI KNOB to enter
BALANCE.
7 Press ESC button to exit
FADER.
2 Turn MULTI KNOB to select
AUDIO CTRL.
2 Turn MULTI KNOB to select
AUDIO CTRL.
1 Press MULTI KNOB to
display the menu.
6 Turn MULTI KNOB to adjust
the BALANCE.
7 Press ESC button to exit
BALANCE.
BASS: Use bass to adjust the low-pitched tones.
The display ranges from –5 to 5.
HOW TO CHANGE THE BASS SETTING
1 Press MULTI KNOB to
display the menu.
7 Press ESC button to exit
BASS.
TREBLE:
Use treble to adjust the high-pitched
tones. The display ranges from –5 to 5.
HOW TO CHANGE THE TREBLE SETTING
2 Turn MULTI KNOB to select
AUDIO CTRL.
3 Press MULTI KNOB to enter
AUDIO CTRL.
4 Turn MULTI KNOB to select
BASS.
5 Press MULTI KNOB to enter
BASS.
6 Turn MULTI KNOB to adjust
the TREBLE.
1 Press MULTI KNOB to
display the menu.
7 Press ESC button to exit
TREBLE.
2 Turn MULTI KNOB to select
AUDIO CTRL.
3 Press MULTI KNOB to enter
AUDIO CTRL.
4 Turn MULTI KNOB to select
TREBLE.
6 Turn MULTI KNOB to adjust
the BASS.
5 Press MULTI KNOB to enter
TREBLE.
11
<CRB3881-B/U>11
During driving, noise in the car changes
according to the driving speed. The
Automatic Sound Levelizer (ASL)
automatically adjusts the volume based
on driving speed. If this noise becomes
greater, the sensitivity (variation of
volume level to noise level) of ASL can
be set to one of three levels. Press the
MULTI KNOB changes the ASL setting
as follows:
LOW  MID  HIGH  OFF
SUB-W: Subwoofer output phase can be
switched between normal and reverse
by pressing the MULTI KNOB, turn the
MULTI KNOB up or down to adjust
the output level of the subwoofer.
Each time MULTI KNOB is turned up
or down, subwoofer level increases or
decreases. (+6 to –24 is displayed as
the level is increased or decreased.)
• The output level and output phase
of the subwoofer can be adjusted
only when "SUB-W CTRL" on the
SETUP menu is set to ON. While
"SUB-W CTRL" is set to OFF, the
output level and output phase cannot
be adjusted. (Refer to page 56.)
ASL:
12
<CRB3881-B/U>12
ASR:
The ASR (Sound Retriever) function
provides a wide, deep and rich quality
to MP3/WMA/AAC sound, which gives
the user a lively impression. Pressing the
MULTI KNOB repeatedly switches the
setting in the following order:
LOW RATE  HIGH RATE  OFF
LOW RATE:
Effective for low-compression audio media.
HIGH RATE:
Effective for high-compression audio media.
NOTICE
• The ASR function can only be
selected when playing MP3/
WMA/AAC from CD and iPod,
USB portable audio player/
USB memory/Bluetooth audio.
• The ASR function does not
support external compressed
audio media.
• Switching of ASR settings is
disabled in Bluetooth audio
mode when no Bluetooth
device is connected or when
settings cannot be switched.
• BASS function and TREBLE
function values can be set for
each of the modes (AM, FM,
CD/MP3/WMA/AAC, iPod/USB
portable audio player/USB
memory, XM Satellite Radio,
Bluetooth audio player, AUX).
When you switch modes, the
settings change to the BASS
and TREBLE values set for the
selected mode.
• The ASL function is only
effective when the vehicle is
moving.
• SETTINGS
You can select this item in TUNER
mode or iPod mode.
If you select SETTINGS, you can set
the following items.
• HD ON/OFF (in TUNER mode)
• IPOD DIRECT (in iPod mode)
• AUDIO BOOK (in iPod mode)
To select a setting option in iPod
mode, turn the MULTI KNOB clockwise or counterclockwise and press
the MULTI KNOB.
IPOD DIRECT  AUDIO BOOK
HD ON/OFF:
If you set HD ON/OFF to ON, digital
broadcasting is preferentially selected.
During SCAN or SEEK operations, the
tuner searches for all digital and analog
broadcasting stations.
If you set HD ON/OFF to OFF, only
analog broadcasting is selected. During
SCAN or SEEK operations, the tuner
searches only for analog broadcasting
stations.
When the MULTI KNOB is pressed,
switches in the following order:
ON  OFF
• The setting can only be changed in
TUNER mode.
IPOD DIRECT:
A menu for turning on or off iPod direct
control (in iPod mode). If you select ON,
you can control iPod operations on the
iPod, and you can control only the volume of iPod from this unit. If you select
OFF, you can control iPod operations
from this unit.
When the MULTI KNOB is pressed,
switches in the following order:
OFF  ON
• The setting can only be changed in
iPod mode.
AUDIO BOOK:
You can change the iPod Audiobook
playback speed.
Pressing the MULTI KNOB repeatedly
switches the setting in the following
order:
NORMAL  FASTER  SLOWER
• The speed can only be changed in
iPod mode.
• While IPOD DIRECT is set to ON, the
speed cannot be changed.
NOTICE
iPod (5th generation) and iPod
nano (1st generation) do not
support iPod direct control.
• BLUETOOTH
If you select BLUETOOTH, you can
make the settings for connecting and
controlling Bluetooth devices.
To select the following setting
options, turn the MULTI KNOB
clockwise or counterclockwise and
press the MULTI KNOB. Refer to
page 42 for more details on the following "Bluetooth Settings".
BT PAIRING:
You can connect your Bluetooth
devices.
LIST PHONE:
You can connect or disconnect a registered Bluetooth-compatible mobile
phone, or delete it from the list.
LIST AUDIO:
You can connect or disconnect a registered Bluetooth device, delete the
device from the list, and select the
connection method.
SET PASSKEY:
You can set the passkey.
BT POWER ON/BT POWER OFF:
You can select whether or not to automatically connect a Bluetooth device
when the ignition switch is set to ON.
BT INFO:
You can check the name and address
of this unit.
13
<CRB3881-B/U>13
DISPLAY ON/DISPLAY OFF:
You can select whether or not to display the connection confirmation when
a Bluetooth device is connected by
setting the ignition switch to ON.
INITIALIZE:
You can initialize certain setting information or all settings.
• PHONE
If you select PHONE, you can edit
the phonebook, set the ring tone or
transfer the call histories.
To select the following items, turn
the MULTI KNOB clockwise or counterclockwise and press the MULTI
KNOB.
PHONE BOOK  SET HF SOUND  SEND
HISTORY
PHONE BOOK:
You can edit the phonebook in this
unit.
SET HF SOUND:
When a mobile phone is connected,
you can select the ring tone and adjust
the volume of the call tone and ring
tone.
SEND HISTORY:
You can transfer the call histories on
the connected mobile phone to this
unit.
When the MULTI KNOB is pressed,
switches in the following order:
YES  NO
14
<CRB3881-B/U>14
3 BACK
Press the BACK button to exit from
the menu.
Press and hold the BACK button to
exit from a list that was displayed by
pressing the LIST/MENU button.
15
<CRB3881-B/U>15
Listening to the RADIO
1 FM1/2
Switches between FM1 and FM2
modes.
2 AM•SAT
Switches between the AM mode and
SAT1/2/3 modes. (Must have Satellite
Radio receiver and antenna installed at
an additional charge to listen to Satellite
Radio.)
3 LIST/MENU
Press to display the registered broadcasting station list in PRESET 1-6.
Use the MULTI KNOB to select a station from the list.
16
<CRB3881-B/U>16
4 MULTI KNOB (SELECT LIST)
Turn the MULTI KNOB clockwise
or counterclockwise to select a station. Press the MULTI KNOB to set
the station. If you press and hold the
MULTI KNOB in the center until you
hear a beep, the currently tuned station is stored as a preset channel in
the preset channel list.
5 RIGHT (TUNE <UP>)
Press to manually select (one step
at a time) the station with the next
higher frequency. Press and hold to
fast-forward to a higher frequency.
6 UP (TUNE <UP>)
Press to select the next higher station.
Press and hold to continue searching
for a higher frequency station.
7 LEFT (TUNE <DOWN>)
Press to manually select (one step
at a time) the station with the next
lower frequency. Press and hold to
fast-forward to a lower frequency.
8 DOWN (TUNE <DOWN>)
a SCAN
If you press,
is indicated in the
display. The tuner begins searching
for stations with good reception and
you can listen to each channel for 5
seconds.
Press to select the next lower
station.
Press and hold to continue searching
for a lower frequency station.
9 PRESET 1-6
Press to recall previously stored stations (Preset Channels).
Press and hold until you hear a
beep, and the station you are currently tuned to is stored as a Preset
Channel.
NOTICE
You can store up to 6 stations
per band.
17
<CRB3881-B/U>17
Listening to the
HD Radio broadcast
HD RadioTM Technology is a terrestrial
digital radio broadcast that utilizes
AM/FM analog broadcasting frequencies to transmit digital signals.
For information regarding viewing
methods, refer to Listening to the
RADIO (page 16). This section contains explanations solely regarding
HD Radio broadcast functions.
About HD Radio™ broadcasting
HD Radio™ broadcasting is high quality audio
and data services. HD Radio broadcasting is
brought to you by your local FM/AM stations.
HD Radio broadcasting features the following:
• High quality audio
• FM multicasting
• Data services
18
<CRB3881-B/U>18
When
receiving
last SPS
(MPS)
(MPS)
(MPS)
(SPS)
(SPS)
1 RIGHT (TUNE <UP>)
When receiving the HD Radio
Broadcast signal and tuning in a
Multicast Channel-supported broadcast in something other than analog,
the following actions will occur each
time you press.
When
receiving
MPS
signal
When
receiving
SPS
signal
The first SPS is tuned in.
The next MPS is tuned
in.
2 LEFT (TUNE <DOWN>)
When receiving the HD Radio
Broadcast signal and tuning in a
Multicast Channel-supported broadcast in something other than analog,
the following actions will occur each
time you press.
When
receiving
MPS
signal
When
receiving
SPS
signal
When
receiving
next SPS
signal
NOTICE
• When an analog station is
received, tuning down operation
is conducted within the analog
broadcasting. (62)
• If a digital broadcast is not yet
received, tuning-up operation
tunes in the next analog station.
(26)
The previous MPS is
tuned in.
The previous SPS is
tuned in. Or, the next
MPS is tuned in.
The first SPS is tuned in.
3 TEXT
If you press while the HD Radio
broadcasting signal is being received,
the display switches in the following
order.
Artist Name
Upper: Station Name

Song Title
Lower: Frequency

The next SPS is tuned in.
Album Title
Song Title
When  is displayed, if you press
and hold until you hear a beep, the
display will changes. A maximum of
2 pages (24 characters) can be displayed.
19
<CRB3881-B/U>19
Listening to a CD
NOTICE
• Never try to disassemble or
oil any part of the compact
disc player. Do not insert
anything except a compact
disc into the slot.
• Use 12-cm discs. Do not use
8-cm discs or an adapter for
8-cm discs.
Load a CD in the CD slot.
No title name is displayed when playing back a CD containing no text information.
20
<CRB3881-B/U>20
1 DISC
Switches to the CD mode. (Only
effective if a disc is loaded.)
2  (EJECT)
Press to eject the disc.
3 LIST/MENU
Press to display a CD List.
Use the MULTI KNOB to select a CD
from the list.
4 MULTI KNOB (SELECT LIST)
Turn the MULTI KNOB clockwise
or counterclockwise to select the
desired title. Press the MULTI KNOB
in the center to start playback.
• No CD List is displayed when playing back a CD containing no text
information.
5 UP/DOWN (SELECT LIST)
Press to select the desired title.
6 RIGHT (TRACK <UP>)
Press to proceed to the next track.
Press and hold until you hear a beep.
Playing of the track is fast forwarded.
(There is sound.)
7 LEFT (TRACK <DOWN>)
Press to takes you back to the start
of the track currently playing. Press
to return to the previous track once
more.
Press and hold until you hear a beep.
Playing of the track is reversed.
(There is sound.)
8 PRESET 1 (PLAY/PAUSE)
To pause the CD, press PRESET 1
while the CD is playing. Press again
to resume playing.
9 PRESET 5 (Random)
If you press this,
and
is
indicated in the display. This unit
starts to play tracks on the disc being
played in random order. Press again
to cancel.
a PRESET 6 (Repeat)
If you press this, and
is indicated in the display. This unit starts
to repeat the track being played.
Press again to cancel.
c TEXT
Press, and display indications change
as follows (TEXT CD only):
Upper: Artist Name
Lower: Track Title


Track Title
ELAPSED TIME
Disc Title
Track Title
When  is displayed, if you press
and hold until you hear a beep, the
display will changes. A maximum of
2 pages (24 characters) can be displayed.
CAUTION
Compact disc players use an
invisible laser beam which
could cause hazardous radiation
exposure if directed outside
the unit. Be sure to operate the
player correctly.
b SCAN
If you press this, and
is indicated in the display. This unit starts
to play the first 10 seconds of each
track on the CD being played. Press
again to cancel.
21
<CRB3881-B/U>21
Listening to MP3/
WMA/AAC DISC
1 DISC
Switches to the DISC mode. (Only
effective if a disc is loaded.)
2  (EJECT)
Press to eject the disc.
3 LIST/MENU
Press to display an MP3/WMA/AAC List.
Use the MULTI KNOB to select an item
from the list.
4 MULTI KNOB (SELECT LIST)
Turn the MULTI KNOB clockwise or
counterclockwise to select a file or
folder.
Press the MULTI KNOB in the center
to play the selected file or folder. Use
the MULTI KNOB to select an item
from the list.
(When a folder is selected, the first
track in the folder is played.)
The MP3/WMA/AAC List is displayed when the top folder in the
root directory or the file or folder
name is selected.
22
<CRB3881-B/U>22
5 RIGHT (TRACK <UP>)
Press to proceed to the next file.
Press and hold until you hear a beep.
Playing of the file is fast forwarded.
(There is no sound.)
6 LEFT (TRACK <DOWN>)
Press to takes you back to the start
of the file currently playing. Press to
return to the previous file once more.
Press and hold until you hear a beep.
Playing of the file is reversed. (There
is no sound.)
7 UP (FOLDER <UP>)
Press to proceed to the next folder.
8 DOWN (FOLDER <DOWN>)
Press to return to the previous folder.
Press and hold until you hear a beep
to jump to HOME.
HOME means returning back to play
the first file in the first folder on the
CD being played.
9 PRESET 1 (PLAY/PAUSE)
To pause the track, press PRESET
1 while the track is playing. Press
again to resume playing.
a PRESET 5 (Random)
If you press this,
and
is indicated in the display. This unit starts
to play files in the folder being played
in random order. Press again to cancel.
If you press and hold until you hear a
beep,
and
is indicated in the
display. This unit starts to play files in
all folders on the disc being played in
random order. Press again to cancel.
b PRESET 6 (Repeat)
If you press this, and
is indicated in the display. This unit starts
to repeat the file being played. Press
again to cancel.
If you press and hold until you hear a
beep,
and
is indicated in the
display. This unit starts to repeat the
folder being played. Press again to
cancel.
d TEXT
Press and display indications change
as follows:
Upper: Artist Name
Track Title

Lower: Track Title
ELAPSED TIME

Folder Name
File Name
When  is displayed, if you press
and hold until you hear a beep, the
display will changes. A maximum of
2 pages (24 characters) can be displayed.
c SCAN
If you press this, and
is indicated in the display. This unit starts
to play the first 10 seconds of each
file in the folder being played. Press
again to cancel.
If you press and hold until you hear a
beep,
and
is indicated in the
display. This unit starts to play the
first 10 seconds of the first file of
each folder. Press again to cancel.
23
<CRB3881-B/U>23
NOTICE
When playing back a disc
recorded with the Multi
Session system, the first
session only is played back.
If the first session combines
MP3, WMA and AAC files
and music data (CD-DA), this
product only plays the music
data. (Refer to page 58.)
About handling the
iPod
About iPod settings
• This unit supports only an iPod
featuring the Dock connector
port.
• Operations may vary depending
on the software version of iPod.
• The iPod Equalizer setting set by
the iPod is not used.
• The Shuffle function of the iPod
is operated as Random on this
unit.
CAUTION
• Store the data into another
media, to avoid losing the
data during iPod operation
with this unit.
• Do not allow direct
sunlight to fall on the
iPod when it is not being
used. Extended exposure
to direct sunlight can
result in iPod malfunction
due to the resulting high
temperatures.
• Do not leave the iPod in
high temperatures or direct
sunlight.
• Fix the iPod securely when
using with this unit. Do not
let the iPod fall onto the floor,
where it may become jammed
under the brake or accelerator
pedal.
For details, refer to the User Guide
of your iPod.
24
<CRB3881-B/U>24
About iPod software version
Connecting the iPod
The iPod software versions that
can be used with this unit are as
follows (operations verified as of
October 2010):
Connect the USB connector.
Connect the iPod as indicated
in the figure below using a USB
cable.
Push the Dock connector into the
Dock connector port until you
hear a click to connect firmly. If it
does not go in smoothly, it may be
upside down so do not force it in as
this may result in damage.
Made for
iPod (5th generation)
iPod classic
iPod classic 120 GB
iPod classic 160 GB
iPod nano (1st generation)
iPod nano (2nd generation)
iPod nano (3rd generation)
iPod nano (4th generation)
iPod nano (5th generation)
iPod nano (6th generation)
iPod touch (1st generation)
iPod touch (2nd generation)
iPod touch (3rd generation)
iPod touch (4th generation)
iPhone
iPhone 3G
iPhone 3GS
iPhone 4
ver. 1.3
ver. 2.0
ver. 2.0.1
ver. 2.0.4
ver. 1.3.1
ver. 1.1.3
ver. 1.1.3
ver. 1.0.4
ver. 1.0.1
ver. 1.0
iOS3.0
iOS3.0
iOS3.1.1
iOS4.1
iOS3.1.2
iOS3.0
iOS3.0.1
iOS4.1
* Please note that no guarantee applies to iPod
operations and future updated versions of iPod
software.
iPod with Dock connector port
USB port
*1
To the vehicle's
USB connector
*2
Dock connector
When connecting the iPod, remove
a headphone cable from the iPod.
When connecting the iPod, it is
recommended to use a separately
purchased car kit.
*1
It is recommended to use a USB cable which
satisfies USB 2.0 standards.
(Measurements should satisfy USB 2.0 standards.)
*2
Connection location differs depending on the
vehicle.
Vehicle Connection location
type
tC
Connect to the USB connector
near the shift knob.
xB
Connect to the USB connector
near the parking brake.
xD
Connect to the USB connector
near the cup holder.
iQ
Connect to the USB connector
near the shift knob.
FR-S Connect to the USB connector
near the shift knob.
As soon as the iPod is connected, its
power is automatically turned on.
While the iPod is connected to this
unit, the Apple logo (or
(check
mark)) is displayed on the iPod.
• While the iPod is connected to
this unit, the iPod itself cannot be
turned on or off.
• You cannot use the iPod's
remotecontrol at the same time.
• You may hear noise if you
disconnect during iPod playback.
25
<CRB3881-B/U>25
NOTICE
• To resolve most problems
when using your iPod with
the Scion Audio system,
disconnect your iPod from the
vehicle iPod connection and
reset it.
• For instructions on how to
reset your iPod, refer to the
User Guide of your iPod.
• Connect the Dock connector
directly to the iPod with
Dock connector port. Do not
connect it via the iPod Dock
or other connection.
• When the iPod is connected
to this unit, sound will
also be heard from the
headphone of the iPod.
Disconnect the headphone
from the iPod before use.
• If you install an audio
system other than a Scion
Genuine Audio, you will
not be able to use the USB
connector.
26
<CRB3881-B/U>26
• If the iPod does not operate
with Scion Audio system,
disconnect the connector
from the iPod and reconnect again.
Disconnecting the iPod
Remove the connector.
• When you are using iPhone by
the multitasking, according to
the application under use, it
might not be able to charge a
battery.
NOTICE
If after updating iPod or iPhone
with latest software/firmware
(iTunes), if this product does not
recognize the connected iPod/
iPhone or otherwise behaves
erratically, follow the steps below.
1. Disconnect the iPod/iPhone
cable and then reconnect it.
2. Turn the iPod/iPhone off and
then turn the device back on
again.
3. Disconnect the cable from the
iPod/iPhone and reset them.
After starting up the iPod/
iPhone, connect the product
using a cable.
When disconnecting the iPod
connector, grasp the connector
firmly and pull it towards you.
27
<CRB3881-B/U>27
Listening to songs on
the iPod
1 iPod•USB
Press the button repeatedly until the
source becomes iPod.
NOTICE
If an iPod is not connected, it
will not switch to iPod even if
you press the iPod•USB button.
2 LIST/MENU
Press the LIST/MENU button to
display the category list (Playlist is
the first category displayed). Use the
MULTI KNOB to change or select
the category.
3 MULTI KNOB (SELECT LIST)
Turning the MULTI KNOB while the
list is displayed switches the categories in the following order. Press the
MULTI KNOB in the center to select.
Playlist Artists  Albums 
Songs  Podcasts  GENRES 
Composers  Audio Book
Turn the MULTI KNOB to select an
item from the selected category, and
press the MULTI KNOB in the center
to select.
28
<CRB3881-B/U>28
4 RIGHT (TRACK <UP>,
CHAPTER<UP>)
Press to proceed to the next track or
chapter.
Press and hold to the right until you
hear a beep. Playing of the track is
fast forwarded.
5 LEFT (TRACK <DOWN>,
CHAPTER <DOWN>)
Press to takes you back to the beginning of the track currently playing or
previous chapter.
Press to return to the previous track
or chapter once more.
Press and hold until you hear a beep.
Playing of the track is reversed.
6 PRESET 1 (PLAY/PAUSE)
To pause the track, press PRESET
1 while the track is playing. Press
again to resume playing.
7 PRESET 5 (Random)
If you press this,
is indicated in
the display. This unit starts to play
tracks on the iPod being played in
random order.
Pressing PRESET 5 repeatedly
switches between the contents of
random and Off.
The random changes as follows:
Track Shuffle  Album Shuffle  Off
Press and hold PRESET 5 to set
Shuffle all.
8 PRESET 6 (Repeat)
If you press this, and
is indicated in the display. This unit starts
to repeat the track being played.
Press again to cancel.
9 TEXT
Text information recorded on the
iPod can be displayed.
Up to 16 characters can be displayed
at once.
Press and display indications change
as follows:
Upper: Artist Name
Song Title

Lower: Song Title
ELAPSED TIME

Album Title
Song Title
When  is displayed, if you press
and hold until you hear a beep, the
display will changes. A maximum of
2 pages (24 characters) can be displayed.
NOTICE
• You cannot use the iPod’s
remote control at the same
time.
• You may hear noise if you
disconnect during iPod
playback.
• The SCAN operation is not
available when listening to
the iPod.
29
<CRB3881-B/U>29
ABC SEARCH on an iPod
You can search for an item in the
list displayed on the iPod by the
first character (alphanumeric characters only).
1 Press the LIST/MENU button.
While the list is displayed, press
the LIST/MENU button again.
ABC SEARCH is enabled.
2 Turn the MULTI KNOB to select
a letter or numeral. For example,
turn the MULTI KNOB right to
select “B”.
3 Press the MULTI KNOB.
The search starts and the first
item in the list that starts with
“B” is displayed.
30
<CRB3881-B/U>30
If the list does not contain any
items starting with the selected
character, “NOT FOUND” is
displayed and ABC SEARCH is
canceled.
4 Turn the MULTI KNOB to select
the desired track.
Scroll down the list.
5 When the track you want to listen
to is displayed in the center of the
display, press the MULTI KNOB
in the center. The selected track
is played.
* To cancel ABC SEARCH,
press the LIST/MENU button.
About handling the
USB portable audio
player/USB memory
Connecting the USB
portable audio player/
USB memory
• For information on USB portable
audio player/USB memory
restrictions, refer to page 61
“USB portable audio player/USB
memory compatibility”.
• For information on restrictions
on folders in the USB portable
audio player/USB memory, refer
to page 60 “About folders and
MP3/WMA/AAC files”.
• Connect the USB portable audio
player/USB memory to the USB
port of the USB connector.
• For instructions on connecting
and disconnecting the iPod, refer
to page 25 “Connecting the iPod”
and page 26 “Disconnecting the
iPod”.
31
<CRB3881-B/U>31
Listening to USB
portable audio player/
USB memory
1 iPod•USB
Press the button repeatedly until the
source becomes USB portable audio
player/USB memory.
For information on playback operations after switching the source to
USB, refer to page 22 “Listening to
MP3/WMA/AAC DISC”.
32
<CRB3881-B/U>32
33
<CRB3881-B/U>33
NOTICE
An additional Genuine Toyota
satellite receiver and antenna
must be purchased and installed
to listen to Satellite radio
broadcast in your vehicle.
NOTICE
An XM Satellite Radio subscription is required to listen to
Satellite radio in your vehicle.
34
<CRB3881-B/U>34
CAUTION
• This XM tuner supports Audio Services (Music and Talk) of only XM
Satellite Radio and *Text Information linked to the respective Audio
Service.
*Text Information includes, Station Name, (Artist) Name, (Song) Title and
Category Name.
• Sirius XM Radio, Inc. is solely responsible for providing services
over the air to XM receivers.
• This XM tuner is awarded a Type Approval Certificate from Sirius
XM Radio, Inc. as a proof of compliance for the services XM Satellite
Radio provides.
How to subscribe to
XM Satellite Radio
<Option>
NOTICE
All fees and programming are
the responsibility of XM Satellite
Radio and are subject to change.
Listeners can subscribe by visiting
the website at
www.siriusxm.com or by calling
Listener Care toll-free at
(866)-635-2349.
Customers should have their Radio
ID ready.
Display the RADIO ID
Each XM tuner is identified with a
unique Radio ID. You will need the
Radio ID when activating XM service or when reporting a problem.
How to display RADIO ID
Select the Channel Number zero (000)
by turning the MULTI KNOB or pressing
it to the left or right.
The ID Code is displayed.
The RADIO ID is displayed as 8
alphanumeric characters.
(Refer to page 36 to check your radio
ID code.)
Record your ID Code below
ID CODE ___ ___ ___ ___ ___ ___ ___ ___
NOTICE
If you select another Channel,
display of the ID Code is
canceled.
35
<CRB3881-B/U>35
Radio ID
Refer to the corresponding chart
to verify the Radio ID Code before
contacting XM Satellite Radio to
activate your service.
Corresponding chart
36
<CRB3881-B/U>36
37
<CRB3881-B/U>37
Listening to a XM
Satellite Radio
broadcast
1 AM•SAT
Switches between the AM mode
and SAT1/2/3 modes.
NOTICE
Must have XM Satellite Radio
receiver, antenna and service
installed at an additional charge
to listen to XM Satellite Radio.
(Refer to pages 34 to 35.)
2 LIST/MENU
Press to select the preset channel
list mode.
Use the MULTI KNOB to select a
channel from the list.
38
<CRB3881-B/U>38
3 MULTI KNOB (SELECT LIST)
Turn the MULTI KNOB clockwise
or counterclockwise to select the
desired channel. Broadcast will start
by pressing. If you press and hold
until you hear a beep, the currently
tuned station is stored as a preset
channel in the preset channel list.
4 RIGHT (TUNE <UP>)
Press to select the next higher channel.
If you press and hold, you can rapidly
scroll forward through the channels.
While displaying Channel Category
by TYPE UP/DOWN, you can select
the next channel forward within the
currently selected type (Channel
Category) by pressing.
5 LEFT (TUNE <DOWN>)
Press to select the previous channel.
If you press and hold, you can rapidly
scroll down through the channels.
While displaying Channel Category
by TYPE UP/DOWN, you can select
the previous channel within the
currently selected type (Channel
Category) by pressing the MULTI
KNOB to the left.
6 UP (TYPE <UP>)
Press to see the Channel Category
of the channel that is currently
received.
When Channel Category is displayed, press again to switch to the
next category.
7 DOWN (TYPE <DOWN>)
Press to see the Channel Category
of channel that is currently received.
When Channel Category is displayed, press again to switch to the
previous category.
9 SCAN
If you press,
is indicated in
the display. SCAN of the currently
selected type (Channel Category)
starts and the tuner begins searching for stations with good reception.
You can listen to each channel for 5
seconds.
a TEXT
Press this button and the indications
in the display changes as follows:
Upper: Artist Name
Lower: Song Title

Channel Name
Song Title
8 PRESET 1-6
Press to recall previously stored
channels (Preset Channels).
Press and hold until you hear a beep,
and the channel you are currently
receiving will be stored as a Preset
Channel.
NOTICE
NOTICE
About the Display
Up to a maximum of 10
alphanumeric characters can be
displayed.
(Some information will not be
fully displayed.)
You can store up to 6 channels
per band.
39
<CRB3881-B/U>39
Using the AUX
By inserting a mini plug into the
car AUX adapter, you can listen to
music from a portable audio device
through the vehicle’s speaker system.
1 iPod•USB
Switches to the AUX mode.
CAUTION
When using a portable audio
device connected to the
power outlet or cigarette
lighter, noise may occur
during playback.
If this happens, use the
power source of the portable
audio device.
40
<CRB3881-B/U>40
NOTICE
• If the mini plug of a
commercially available
cable connected to
a portable audio or
other component is not
connected to the car AUX
adapter, the mode will
not change to the AUX
mode even if you press the
iPod•USB button.
• Volume level when playing
a component connected
with a mini plug differs
to that when listening
to the built-in CD player
or radio so please make
adjustments.
• If you install an audio
system other than a Scion
Genuine Audio, you will not
be able to use the car AUX
adapter.
41
<CRB3881-B/U>41
Bluetooth Settings
With this unit, you can make calls
from a Bluetooth-compatible
mobile phone or play music on the
audio player.
The following Bluetooth profiles/
protocols are compatible with this
unit.
• HFP
• OPP
• PBAP
• A2DP
• AVRCP
• SDP
To make the settings for the
Bluetooth device, display the
BLUETOOTH menu by the following operation.
1 Press MULTI KNOB to
display the menu.
3 Press MULTI KNOB to enter
BLUETOOTH.
Pairing a Bluetooth Device
You can connect a Bluetooth
device by the following operation.
HOW TO CONNECT Bluetooth HANDSFREE PHONE
1 Turn the MULTI KNOB to
select BT PAIRING.
2 Press MULTI KNOB to enter
BT PAIRING.
3 Send the passkey from the
mobile phone.
4 Connection is completed
when “CONNECTED” is
displayed.
2 Turn MULTI KNOB to select
BLUETOOTH.
The device is registered in
the Bluetooth list in this unit.
You can register up to five
devices.
42
<CRB3881-B/U>42
Switching between registered Bluetooth
devices
You can connect a registered
Bluetooth mobile phone by the following operation.
1 Turn the MULTI KNOB to
select LIST PHONE, and press
the MULTI KNOB.
2 Turn the MULTI KNOB to
select the phone you want to
connect from the phone list,
and press the MULTI KNOB.
3 Turn the MULTI KNOB to
select SELECT, and press the
MULTI KNOB.
If another phone is already
connected, turn the MULTI
KNOB to select YES (disconnect) or NO (not disconnect). Disconnection is
completed when indicated
“DISCONNECT BLUETOOTH
DEVICE” is disappeared.
Return to step 2, when disconnection is completed.
Connection is completed when
“CONNECTED” is displayed.
Connecting a Registered Bluetooth Audio
Player
You can connect a registered
Bluetooth audio player by the following operation.
1 Turn the MULTI KNOB to
select LIST AUDIO, and press
the MULTI KNOB.
Subsequent operation is the same
as from Step 2 on in “Switching
between registered Bluetooth
devices”.
Disconnecting a Bluetooth Mobile Phone
You can disconnect a Bluetooth
mobile phone by the following
operation.
1 Turn the MULTI KNOB to
select LIST PHONE, and press
the MULTI KNOB.
2 Turn the MULTI KNOB to
select the phone you want to
disconnect from the phone list,
and press the MULTI KNOB.
3 Turn the MULTI KNOB to
select DISCONNECT, and
press the MULTI KNOB.
4 Turn the MULTI KNOB to
select YES, and press the
MULTI KNOB.
Disconnection is completed
when indicated “DISCONNECT
BLUETOOTH DEVICE” is disappeared.
Disconnecting a Bluetooth Audio Player
You can disconnect a Bluetooth
audio player by the following
operation.
1 Turn the MULTI KNOB to
select LIST AUDIO, and press
the MULTI KNOB.
Subsequent operation is the
same as from Step 2 on in
“Disconnecting a Bluetooth
Mobile Phone.”
Changing the Connection Method of the
Bluetooth Audio Player
You can change the connection
method of the Bluetooth audio
player by the following operation.
1 Turn the MULTI KNOB to
select LIST AUDIO, and press
the MULTI KNOB.
2 Turn the MULTI KNOB to
select the audio player you
want to change the connection
method from the audio player
list, and press the MULTI
KNOB.
3 Turn the MULTI KNOB to
select CONNT METHOD, and
press the MULTI KNOB.
4 Turn the MULTI KNOB and
select FROM VEHICLE to
make the connection from the
unit or FROM AUDIO to make
the connection from the audio
player, and press the MULTI
KNOB. Changing is completed
when the selected connection
method is displayed.
Deleting a Registered Bluetooth Mobile
Phone from the List
You can delete a registered
Bluetooth mobile phone from the
list by the following operation.
1 Turn the MULTI KNOB to
select LIST PHONE, and press
the MULTI KNOB.
2 Turn the MULTI KNOB to
select the phone you want to
delete from the phone list, and
press the MULTI KNOB.
3 Turn the MULTI KNOB to
select DELETE, and press the
MULTI KNOB.
4 Turn the MULTI KNOB to
select YES, and press the
MULTI KNOB.
Deletion is completed when
“DELETED” is displayed.
Deleting a Registered Bluetooth Audio
Player from the List
You can delete a registered
Bluetooth audio player from the
list by the following operation.
1 Turn the MULTI KNOB to
select LIST AUDIO, and press
the MULTI KNOB.
Subsequent operation is the same
as from Step 2 on in “Deleting
a Registered Bluetooth Mobile
Phone from the List”.
Setting a Passkey
You can set the passkey. The
passkey is a number consisting
of between 4 and 8 digits. The
default setting is “0000.” You can
enter the number at the flashing
cursor position.
1 Turn the MULTI KNOB to
select SET PASSKEY, and
press the MULTI KNOB.
2 Turn the MULTI KNOB to
select any number, and press
the MULTI KNOB to the right
to move the cursor to the next
digit.
3 When you have input the last
number, press the MULTI
KNOB to store the passkey.
43
<CRB3881-B/U>43
Setting Automatic Connection of a
Bluetooth Device
You can select whether or not
a Bluetooth device is automatically connected when the ignition
switch is set to ON.
1 Turn the MULTI KNOB to
select BT POWER ON (connect automatically) or BT
POWER OFF (do not connect
automatically), and press the
MULTI KNOB.
Checking Device Information
You can check the device name of
this unit and the Bluetooth device
address.
1 Turn the MULTI KNOB to
select BT INFO, and press the
MULTI KNOB.
2 Turn the MULTI KNOB to
select DEVICE NAME or
DEVICE ADDR (Bluetooth
Device Address), and press the
MULTI KNOB.
You can check the selected
information item.
44
<CRB3881-B/U>44
Setting Connection Confirmation
You can select whether or not to
display the connection confirmation when the ignition switch is
set to ON and a Bluetooth device
is connected.
1 Turn the MULTI KNOB to
select DISPLAY ON (display) or
DISPLAY OFF (hide), and press
the MULTI KNOB.
Initializing Information
You can initialize the hands-free
phone settings (ring tone and
volume), the settings information
for this unit (Bluetooth Power,
Bluetooth connection completion
display and passkey) or all the settings information.
1 Turn the MULTI KNOB to
select INITIALIZE, and press
the MULTI KNOB.
2 Turn the MULTI KNOB to
select SET HF SOUND (to
initialize the tone settings for
the hands-free phone), DEVICE
INFO (to initialize the settings
information for this unit) or ALL
INITILZE (to initialize all the
settings), and press the MULTI
KNOB.
3 Turn the MULTI KNOB to
select YES (initialize) or NO
(do not initialize), and press the
MULTI KNOB.
45
<CRB3881-B/U>45
Listening to BluetoothAudio player
1 iPod•USB
Switches to the BT-AUDIO mode.
2 RIGHT (TRACK <UP>)
Tasks can be performed when supported by your Bluetooth device.
Press to proceed to the next file.
Press and hold until you hear a beep.
Playing of the file is fast forwarded.
(There is no sound.)
3 LEFT (TRACK <DOWN>)
Tasks can be performed when supported by your Bluetooth device.
Press to takes you back to the start
of the file currently playing. Press to
return to the previous file once more.
Press and hold until you hear a beep.
Playing of the file is reversed. (There
is no sound.)
4 UP (ALBUM <UP>)
Tasks can be performed when supported by your Bluetooth device.
Press to proceed to the next folder.
46
<CRB3881-B/U>46
5 DOWN (ALBUM <DOWN>)
Tasks can be performed when supported by your Bluetooth device.
Press to return to the previous album.
6 PRESET 1 (PLAY/PAUSE)
Tasks can be performed when supported by your Bluetooth device.
To pause the track, press PRESET
1 while the track is playing. Press
again to resume playing.
7 PRESET 5 (Random)
Tasks can be performed when supported by your Bluetooth device.
If you press this, and
is indicated in the display. This unit starts to
play files in the folder being played in
random order. Press again to cancel.
If you press and hold until you hear a
beep,
and
is indicated in the
display. This unit starts to play files in
all folders on the disc being played in
random order. Press again to cancel.
8 PRESET 6 (Repeat)
Tasks can be performed when supported by your Bluetooth device.
If you press this, and
is indicated in the display. This unit starts
to repeat the file being played. Press
again to cancel.
If you press and hold until you hear a
beep,
and
is indicated in the
display. This unit starts to repeat the
folder being played. Press again to
cancel.
9 SCAN
Tasks can be performed when supported by your Bluetooth device.
If you press this, and
is indicated in the display. This unit starts
to play the first 10 seconds of each
file in the folder being played. Press
again to cancel.
If you press and hold until you hear a
beep,
and
is indicated in the
display. This unit starts to play the
first 10 seconds of the first file of
each folder. Press again to cancel.
a TEXT
Tasks can be performed when supported by your Bluetooth device.
Press and display indications change
as follows:
Upper: Artist Name
Track Title

Lower: Track Title
ELAPSED TIME

Album Title
Track Title
If the profile of your Bluetooth device
is AVRCP 1.0, the display cannot be
switched. “STREAMING AUDIO” is
displayed.
When  is displayed, if you press
and hold until you hear a beep, the
display will changes. A maximum of
2 pages (24 characters) can be displayed.
47
<CRB3881-B/U>47
Phone Settings
You can make the various settings
for using the hands-free phone.
To make the settings, display the
PHONE menu by the following
operation.
NOTICE
Even if a telephone number
containing 25 or more digits
is recorded in the cell phone’s
address book, you cannot
transfer the data to the
phonebook in this unit.
1 Press the MULTI KNOB to display
the AUDIO menu.
2 Turn the MULTI KNOB to select
PHONE, and press the MULTI
KNOB.
Editing the Phonebook
You can add contacts to or delete
contacts from the phonebook in
this unit. You can also delete the
call histories or other phonebooks,
and register numbers from the
phonebook to speed dialing.
To edit the phonebook, turn
the MULTI KNOB to select
PHONEBOOK, and press the
MULTI KNOB to display the
PHONEBOOK menu.
48
<CRB3881-B/U>48
• Adding a Contact
You can transfer contacts individually or all together from a
connected mobile phone to the
phonebook in this unit.
1 Turn the MULTI KNOB to
select ADD CONTACTS, and
press the MULTI KNOB.
2 Turn the MULTI KNOB to
select SEND ALL or SEND
ONE, and press the MULTI
KNOB.
3 Confirm the displayed amount
of the memory remainder,
and turn the MULTI KNOB to
select YES (transfer) or NO
(not transfer), and press the
MULTI KNOB.
“TRANSFERRING” is displayed during data transfer.
When you use an OPP profile
Bluetooth mobile phone,
operate your mobile phone to
transfer the data. When you
use a PBAP profile Bluetooth
mobile phone, the transfer
starts automatically.
Transfer is completed when
“TRANSFERRED” is displayed.
• Deleting a Contact
You can delete individual contacts
from the phonebook in this unit.
1 Turn the MULTI KNOB to
select DEL CONTACTS, and
press the MULTI KNOB.
2 Turn the MULTI KNOB to
select the contact name (or
phone number) that you want
to delete from the phonebook,
and press the MULTI KNOB.
If you turn the MULTI KNOB
to select A-Z SEARCH and
press the MULTI KNOB, you
can select the first letter of
the contact name and narrow
down the search. Select the
first letter of the name from
the alphabet (A to Z) or select
OTHERS (numbers from 0 to 9
and symbols).
3 Turn the MULTI KNOB to
select YES, and press the
MULTI KNOB.
Deletion is completed when
“DELETED” is displayed.
• Registering a Contact to Speed
Dialing
You can register phone numbers
from the phonebook in this unit to
speed dialing.
1 Turn the MULTI KNOB to
select ADD SD, and press the
MULTI KNOB.
2 Turn the MULTI KNOB to
select the contact name (or
phone number) you want to
register to speed dialing and
press the MULTI KNOB, and
press PRESET 1 - 5.
If you turn the MULTI KNOB
to select A-Z SEARCH and
press the MULTI KNOB, you
can select the first letter of
the contact name and narrow
down the search. Select the
first letter of the name from
the alphabet (A to Z) or select
OTHERS (numbers from 0 to 9
and symbols).
3 Turn the MULTI KNOB to
select YES, and press the
MULTI KNOB.
Registration to speed dialing is completed when
“REGISTERED” is displayed.
• Deleting a Phonebook Used
With Another Phone
You can delete a phonebook used
with another phone.
1 Turn the MULTI KNOB to
select DEL OTHER PB, and
press the MULTI KNOB.
2 Turn the MULTI KNOB to
select the name of the phone
in which the phonebook you
want to delete is used, and
press the MULTI KNOB.
3 Turn the MULTI KNOB to
select YES, and press the
MULTI KNOB.
Deletion is completed when
“DELETED” is displayed.
• Deleting a Call History
You can delete the call histories in
this unit.
1 Turn the MULTI KNOB to
select DEL HISTORY, and
press the MULTI KNOB.
2 Turn the MULTI KNOB to
select the history type (CALLS
PLACED, CALLS TAKEN,
MISSED CALLS or ALL
CALLS), and press the MULTI
KNOB.
3 Turn the MULTI KNOB to
select ALL DELETE or the
individual history you want to
delete, and press the MULTI
KNOB.
4 Turn the MULTI KNOB to
select YES, and press the
MULTI KNOB.
Deletion is completed when
“DELETED” is displayed.
49
<CRB3881-B/U>49
Deleting a Phone Number from Speed
Dialing
You can delete any phone number
from speed dialing.
1 Press the CALL, turn the
MULTI KNOB to select SPEED
DIALS, and press the MULTI
KNOB.
2 Press the PRESET button to
which the phone number you
want to delete is registered.
3 Check the phone number and
press PRESET 6.
4 Turn the MULTI KNOB to
select YES, and press the
MULTI KNOB.
Deletion is completed when
“DELETED” is displayed.
50
Displaying a Call History
You can display the call histories
(last call, all calls, missed calls,
calls taken or calls placed). You
can also select any history (without last call) and add it to or delete
it from speed dialing.
1 In the TEL menu, turn the
MULTI KNOB to select ALL
CALLS, MISSED CALLS,
CALLS TAKEN or CALLS
PLACED, and press the MULTI
KNOB.
When the TEL menu is displayed, the number of the last
call is displayed.
2 Turn the MULTI KNOB to
select the history you want to
display, and press the MULTI
KNOB.
<CRB3881-B/U>50
3 Check the phone number.
Registering a Call History to Speed
Dialing
You can register the selected call
history to speed dialing.
The number of the last call, however, cannot be registered to
speed dialing.
1 Referring to “Displaying a Call
History,” display the history
you want to register to speed
dialing.
2 Turn the MULTI KNOB to
select ADD SD, and press the
MULTI KNOB.
3 Press PRESET 1 - 5 to register
the selected call history you
want to register to speed dialing.
Speed dial registration is completed when “REGISTERED”
is displayed.
Deleting a Call History
You can delete the selected call
history.
1 Referring to “Displaying a Call
History”, display the history
you want to delete.
2 Turn the MULTI KNOB to
select DELETE and press the
MULTI KNOB.
3 Turn the MULTI KNOB to
select YES, and press the
MULTI KNOB.
Deletion is completed when
“DELETED” is displayed.
Setting the Hands-free Phone Ring Tone
and Call Volume
You can select the ring tone for
the hands-free phone and set the
ring tone volume and call volume.
The settings can only be made
when a mobile phone is connected.
• Selecting the Ring Tone
You can select a ring tone for the
hands-free phone.
1 Turn the MULTI KNOB to
select SET HF SOUND, and
press the MULTI KNOB.
2 Turn the MULTI KNOB to
select RINGTONE, and press
the MULTI KNOB.
3 Turn the MULTI KNOB to
select the ring tone you want
to set from RINGTONE 1,
RINGTONE 2 and RINGTONE
3, and press the MULTI KNOB.
* Depending on the type of
mobile phone, when the
mobile phone is set for the
ring tone to sound on the connected unit, the set ring tone
rings by the mobile phone even
when not is even the connection to this unit.
• Setting the Call Volume
You can set the call volume of the
hands-free phone.
1 Turn the MULTI KNOB to
select SET HF SOUND, and
press the MULTI KNOB.
2 Turn the MULTI KNOB to
select CALL VOL, and press
the MULTI KNOB.
3 Turn the MULTI KNOB to
select the call volume you
want to set, and press the
MULTI KNOB.
You can set the call volume in
the range of 1 to 63.
• Setting the Ring Tone Volume
You can set the ring tone volume
of the hands-free phone.
1 Turn the MULTI KNOB to
select SET HF SOUND, and
press the MULTI KNOB.
2 Turn the MULTI KNOB to
select RINGTONE VOL, and
press the MULTI KNOB.
3 Turn the MULTI KNOB to
select the ring tone volume
you want to set, and press the
MULTI KNOB.
You can set the ring tone volume in the range of 1 to 63.
Transferring a Call History
You can transfer a call history
from the connected mobile phone
to this unit. This function is only
available when a mobile phone is
connected.
1 Turn the MULTI KNOB to
select SEND HISTORY, and
press the MULTI KNOB.
2 Turn the MULTI KNOB to
select YES, and press the
MULTI KNOB.
Call history transfer is completed when “TRANSFERRED” is
displayed.
51
<CRB3881-B/U>51
Using Hands-Free Phoning
1 CALL
Switches between telephone modes.
Pressing CALL while a phone number is
displayed initiates a call to the displayed
number. Pressing CALL when there is
an incoming call connects the caller.
When you connect the cellular phone
corresponding to the voice recognition
feature, if you press and hold until you
hear a beep, the voice recognition function is activated.
If you press CALL when dialing a call,
when a call is received or while talking
on the phone, the call is switched to a
hands-free telephone call with this unit.
If you press CALL while talking with this
unit, the telephone call is put on hold
(Hold is only provided for the mobile
phone connected to this unit).
If you press CALL while talking with
this unit, another incoming call can be
answered (Taking incoming calls while
talking on the mobile phone is only provided when connected with this unit).
If you press CALL again after receiving
an additional incoming call, the call is
switched back to the original caller.
2 END
Returns to the operation prior to switching to telephone mode. Pressing END
when there is an incoming call blocks
the caller.
52
<CRB3881-B/U>52
3 PRESET 1-5
Making a Call
4 PRESET 6
You can initiate a call from the
phonebook, by speed dialing,
entering the phone number or from
the call histories.
Initiates a call to the registered
phone number.
Mutes your voice and switches the
phone function from this unit to your
mobile phone.
5 TEXT
If you press TEXT when there is
information that cannot finish being
displayed, you can see information
on continuation.
Using the Phonebook
You can make a call from the
phonebook in this unit.
1 Press CALL, turn the MULTI
KNOB to select PHONEBOOK,
and press the MULTI KNOB.
2 Turn the MULTI KNOB to
select the desired contact
name (or phone number) from
the phonebook, and press the
MULTI KNOB.
If you turn the MULTI KNOB
to select A-Z SEARCH and
press the MULTI KNOB, you
can select the first letter of
the contact name and narrow
down the search. Select the
first letter of the name from
the alphabet (A to Z) or select
OTHERS (numbers from 0 to 9
and symbols).
3 Check the phone number and
press CALL.
Using Speed Dialing
You can make a call from the
phone numbers registered to
speed dialing.
1 Press CALL, turn the MULTI
KNOB to select SPEED DIALS,
and press the MULTI KNOB.
2 Press the PRESET button to
which the phone number you
want to call is registered.
3 Check the phone number and
press CALL.
Using the Call Histories
You can make a call by displaying
the call histories (last call, outgoing calls, incoming calls, missed
calls or all calls).
1 In the TEL menu, turn the
MULTI KNOB to select LAST
NUMBER, INCOMIN CALL,
OUTGOIN CALL, MISSED
CALLS or ALL CALLS, and
press the MULTI KNOB.
2 Turn the MULTI KNOB to
select the history you want to
display, and press the MULTI
KNOB (except last call).
3 Check the phone number and
press CALL.
53
<CRB3881-B/U>53
Changing the
Opening Screen
With the main unit switched on
after pressing the Power button,
once the key is turned from the
ACC position to the off position
and back to ACC again, “SCION” is
displayed as the Opening Screen.
Users can edit the text themselves
to make another Opening Screen,
as an alternate to the default
SCION display. Up to a maximum
of 12 characters can be displayed.
The procedure is described on next
page.
54
<CRB3881-B/U>54
Editing the Text
The SETUP menu will be
displayed when MULTI KNOB is
held down while the power is in
“OFF” position. Turn the MULTI
KNOB to select the OPENING.
You can enter the character at
the flashing cursor position. The
character selection method is
described below.
1 Enter the character to PRESET 1,
2 and 3. Turn the MULTI KNOB
right or left to select the character,
and press the RIGHT or LEFT to
move the cursor.
• PRESET 1: Alphabet input (A-Z)
• PRESET 2: Number
• PRESET 3: Space, Deletion
2 After selecting the character,
press the MULTI KNOB right. The
cursor moves to the right, so you
can edit the next character.
(Maximum number of characters
for entry is 12.)
To choose and delete the
character or text, choose the
character with the cursor and then
press PRESET 3 to delete.
3 After character entry, press the
MULTI KNOB to register the text
string.
If the cursor is positioned on the
12th character, press the RIGHT
to register the whole text entered.
New Message Display
The next time the ACC is
switched on, the text edited by
the user will be displayed.
NOTICE
To avoid draining the battery,
do not leave the car audio on
longer than necessary when
the engine is not running.
55
<CRB3881-B/U>55
Initial Setting
To display the SETUP menu, press
and hold the MULTI KNOB while
the power is in "OFF" position.
When the MULTI KNOB is turned,
the setting item of the SETUP
menu will switch in the following
order:
SUB-W CTRL  OPENING  CAR TYPE
SUB-W CTRL:
A menu for switching the subwoofer ON and OFF when a subwoofer is connected.
When switched to ON, you can
hear the sound from the subwoofer and enter the subwoofer
settings on the AUDIO CTRL
menu displayed by pressing the
MULTI KNOB while the power
is in “ON” position.
When switched to OFF, no
sound can be heard from the
subwoofer.
When the MULTI KNOB is
pressed, switches in the following
order:
OFF  ON
OPENING:
A menu for editing the opening
message.
You can edit the opening message
by the following operation.
For details of how to edit the
opening message, refer to page
54 “Changing the Opening
Screen.”
• Move the cursor left and right
with the MULTI KNOB left or
right.
• Choose the text with the MULTI
KNOB left or right.
• Enter alphabet with PRESET 1.
• Enter numbers with PRESET 2.
• Enter spaces with PRESET 3.
• Set the text with the MULTI
KNOB in the center.
CAR TYPE:
A menu for setting up the vehicle
type.
When the MULTI KNOB is
pressed, switches in the following
order:
TC XB  XD  IQ  FR-S
HOW TO SETUP THE RADIO FOR THE
CORRECT VEHICLE
1 Press POWER BUTTON to
turn OFF the radio.
2 Press and Hold MULTI
KNOB to enter the SETUP
menu.
3 Turn MULTI KNOB to
select the CAR TYPE.
4 Press MULTI KNOB to
select CAR TYPE.
5 Press MULTI KNOB to
change the CAR TYPE.
*TC  XB  XD  IQ 
FR-S  TC
6 Press POWER button to
set the sound and exit the
SETUP menu.
56
<CRB3881-B/U>56
Connecting an
external amplifier
When you connect an external
amplifier to RCA connectors,
please install according to the
amplifier manual.
Subwoofer output
CAUTION
• A standard speaker's
input is rated 17.5 W input
(largest 40 W input).
When an amplifier is
connected to the RCA
output, make sure to
change the speaker that
corresponds to the output.
If you connect to a standard
speaker, this may cause to
catch fire, emit smoke, or
cause damage.
NOTICE
• The output of an internal
amplifier will not stop even
when an external amplifier
is connected the RCA output.
When cutting off the internal amplifier output cable,
protect the cut surface to
prevent short circuits.
• Subwoofer output of this
unit is monaural. The
output level cannot be
adjusted with FADER/
BALANCE on the AUDIO
CONTROL Menu.
• Beeps will not be audible
if an external amplifier is
connected to the Front
output.
Using the Steering
Controller
In vehicles equipped with one, you
can use the steering controller to
operate this product.
Operation button names and
functions.
 Volume buttons (, )
Press  to raise the volume level.
Press  to lower the volume level.
 Mode selection button (MODE)
• When power to this product is
OFF:
Press the button and power
switches ON.
• When power to this product is ON:
Each time you press the button the
source* changes. If you continue
pressing the button for an extended
period, power to this product
switches OFF.
*The source switches in the following order:
FM1  FM2  (SAT1)  (SAT2) 
(SAT3)  CD(MP3/WMA/AAC) 
(USB/iPod)  (Bluetooth Audio) 
(AUX)  AM FM1
57
<CRB3881-B/U>57
 Track/station selection button
(,)
• When listening to the radio:
Press the button and the preset
memory is recalled in order. If you
continue pressing the button for an
extended period, automatic station
selection begins.
• When listening to a CD:
Press the button to select a track.
• When listening to MP3/WMA/AAC:
Press the button to select a file.
Press and hold the button to select a
folder.
• When listening to the iPod:
Press the button to select a track.
• When listening to USB portable
audio player/USB memory:
Press the button to select a file.
Press and hold the button to select a
folder.
• When listening to a XM broadcast:
Press the button to recall preset
channels in order.
• When listening to Bluetooth audio
player:
Press the button to select a track.
Press and hold the button to select
an album.
58
<CRB3881-B/U>58
MP3, WMA and AAC
files
• MP3 is short for MPEG Audio Layer 3 and
refers to an audio compression technology
standard.
• WMA is short for Windows Media™
Audio and refers to an audio compression
technology that is developed by Microsoft
Corporation. WMA data can be encoded by
using Windows Media Player.
• AAC is short for Advanced Audio Coding
and refers to an audio compression technology standard.
• With some applications used to encode
WMA files, this unit may not operate correctly.
• With some applications used to encode
WMA files, album names and other text
information may not be correctly displayed.
• This unit allows playback of MP3/WMA/AAC
files on CD-ROM, CD-R, CD-RW discs and
USB portable audio player/USB memory.
Disc recordings compatible with level 1 and
level 2 of ISO9660 and with the Romeo and
Joliet file system can be played back.
• MP3/WMA/AAC files are not compatible
with packet write data transfer.
• The maximum number of characters which
can be displayed for a file name, including
the extension (.mp3, .wma, .m4a), is 24,
from the first character.
• The maximum number of characters which
can be displayed for a folder name is 24.
• In case of files recorded according to the
Romeo file system, only the first 24 characters can be displayed.
• The folder selection sequence for playback
and other operations becomes the writing
sequence used by the writing software.
For this reason, the expected sequence at
the time of playback may not coincide with
the actual playback sequence. However,
there also is some writing software which
permits setting of the playback order.
IMPORTANT
• When naming an MP3/WMA/
AAC file, add the corresponding filename extension (.mp3,
.wma, .m4a).
• This unit plays back files with
the filename extension (.mp3,
.wma, .m4a) as an MP3/WMA/
AAC file. To prevent noise and
malfunctions, do not use these
extensions for files other than
MP3/WMA/AAC files.
MP3 additional
information
• Files are compatible with the ID3 Tag Ver.
1.0, 1.1, 2.2, 2.3 and 2.4 formats for display
of album (disc title), track (track title), artist
(track artist) and comments. Ver. 2.x of ID3
Tag is given priority when both Ver. 1.x and
Ver. 2.x exist.
• The emphasis function is valid only when
MP3 files of 32 kHz, 44.1 kHz and 48 kHz
frequencies are played back. (16 kHz,
22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz sampling frequencies can be
played back.)
• There is no m3u playlist compatibility.
• There is no compatibility with the MP3i
(MP3 interactive) or mp3 PRO formats.
• The sound quality of MP3 files generally
becomes better with an increased bit
rates. This unit can play recordings with
bit rates from 8 kbps to 320 kbps, but
in order to be able to enjoy sound of a
certain quality, we recommend using only
discs recorded with a bit rate of at least
128 kbps.
WMA additional
information
• This unit plays back WMA files encoded by
Windows Media Player.
• You can only play back WMA files in the
frequencies 32 kHz, 44.1 kHz and 48 kHz.
• The sound quality of WMA files generally
becomes better with an increased bit rate.
This unit can play recordings with bit rates
from 48 kbps to 320 kbps (CBR) or from
48 kbps to 384 kbps (VBR), but in order to
be able to enjoy sound of a certain quality,
we recommend using discs recorded with
a higher bit rate.
• This unit doesn't support the following formats.
- Windows Media Audio 9 Professional
(5.1ch)
- Windows Media Audio 9 Lossless
- Windows Media Audio 9 Voice
AAC additional
information
• This unit plays back AAC files encoded by
iTunes.
• This unit plays back AAC files in the sampling frequencies 11.025 kHz, 16 kHz,
22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz and
48 kHz.
• The sound quality of AAC files generally
becomes better with an increased transmission rate. This unit can play recordings
with transmission rates from 16 kbps to
320 kbps, but in order to be able to enjoy
sound of a certain quality, we recommend
using discs recorded with a higher transmission rate.
• This unit doesn't support the following format:
- Apple Lossless
59
<CRB3881-B/U>59
About folders and MP3/
WMA/AAC files
• An outline of a CD-ROM and USB portable audio player/USB memory with
MP3/WMA/AAC files on it is shown below.
Subfolders are shown as folders in the
folder currently selected.
001
(ROOT)
002
001.mp3
(001.wma, 001.m4a)
010.mp3
(010.wma, 010.m4a)
003
011.mp3
(011.wma, 011.m4a)
020.mp3
(020.wma, 020.m4a)
004
021.mp3
(021.wma, 021.m4a)
030.mp3
(030.wma, 030.m4a)
005
First Second Third
level level level
60
<CRB3881-B/U>60
NOTES
• This unit assigns folder
number. The user can not
assign folder numbers.
• MP3/WMA/AAC files in the
USB portable audio player/
USB memory are played
in the same order as they
were copied to the USB
portable audio player/USB
memory.
• To specify the order in
which files in the USB
portable audio player/USB
memory are played, we
recommend the following
method.
1 Using a personal computer,
add a number indicating
the playback order in
front of the file name, e.g.
[001xxx.mp3] or [099yyy.
wma].
2 Put the files into a folder.
3 Copy the folder to the USB
portable audio player/USB
memory.
Depending on the computer
environment, it may not
be possible to specify the
order by this method.
• It is not possible to check
folders that do not include
MP3/WMA/AAC files.
(These folders will be
skipped without displaying
the folder number.)
• MP3/WMA/AAC files in
up to 8 tiers of folders can
be played back. However,
there is a delay in the
start of playback on discs
and USB portable audio
player/USB memory with
numerous tiers. For this
reason we recommend
creating discs with no more
than 2 tiers.
• It is possible to play back
up to 192 folders on one
disc.
• It is possible to play back
up to 255 folders on one
USB portable audio player/
USB memory.
USB portable audio player/
USB memory compatibility
• USB version: 2.0, 1.1 and 1.0
• USB data transfer rate: full speed
• USB Class: MSC (Mass Storage Class) device
• Protocol: bulk
• File system: FAT32 and FAT16
• Supply current: 500 mA
NOTES
• Partitioned USB memory
is not compatible with this
unit.
• Depending on the kind of
USB portable audio player/
USB memory you use, this
unit may not recognize
the USB audio player/USB
memory or audio files
may not be played back
properly.
• This unit can play back
files in the USB portable
audio player/USB memory
that is USB Mass Storage
Class. However, copyright
protected files that are
stored in above-mentioned
USB devices cannot be
played back. (If the iPod is
connected to this unit, file
playback condition depends
on the iPod specifications.)
• You cannot connect a USB
portable audio player/USB
memory to this unit via a
USB hub.
• Not all multimedia portable
devices are compatible.
• We cannot guarantee
compatibility with all USB
mass storage devices and
assumes no responsibility
for any loss of data on media
players, smart phones, or
other devices while using this
product.
61
<CRB3881-B/U>61
Terms
ID3 Tag
Packet write
This is a general term for a method
of writing on CD-R, etc. at the time
required for a file, just as is done
with files on floppy or hard discs.
Bit rate
This expresses data volume per
second, or bps (bits per second)
units. The higher the rate, the more
information is available to reproduce
the sound. Using the same encoding
method (such as MP3), the higher
the rate, the better the sound.
Multi-session
Multi-session is a recording method
that allows additional data to be
recorded later. When recording
data on a CD-ROM, CD-R or CDRW, etc., all data from beginning
to end is treated as a single unit or
session. Multi-session is a method
of recording more than 2 sessions in
one disc.
CD-DA
CD-DA is an abbreviation of
Compact Disc Digital Audio. It refers
to the uncompressed format of
regular CDs.
62
<CRB3881-B/U>62
This is a method of embedding trackrelated information in a MP3 file. This
embedded information can include
the track title, the artist's name, the
album title, the music genre, the
year of production, comments and
other data. The contents can be
freely edited using software with ID3
Tag editing functions. Although the
tags are restricted to the number of
characters, the information can be
viewed when the track is played back.
ISO9660 format
This is the international standard
for the format logic of CD-ROM
folders and files. For the ISO9660
format, there are regulations for the
following two levels.
Level 1:
The file name is in 8.3 format (the
name consists of up to 8 characters,
half-byte English capital letters
and half-byte numerals and the "_"
sign, with a file-extension of three
characters).
Level 2:
The file name can have up to 31
characters (including the separation
mark "." and a file extension).
Each folder contains less than 8
hierarchies.
Extended formats
Joliet:
File names can have up to 64
characters.
Romeo:
File names can have up to 128
charac ters.
m3u
Playlists created using the
"WINAMP" software have a playlist
file extension (.m3u).
MP3
MP3 is short for MPEG1 & 2 Audio
Layer3. It is an audio compression
standard set by a working group
(MPEG) of the ISO (International
Standards Organization). MP3 is able
to compress audio data to about 1/10
the level of a conventional disc.
WMA
WMA is short for Windows MediaTM
Audio and refers to an audio
compression technology that is
developed by Microsoft Corporation.
WMA data can be encoded by using
Windows Media Player version 7 or
later.
AAC
AAC is short for Advanced Audio
Coding and refers to an audio
compression technology standard
used with MPEG2 and MPEG4.
CD player and care
• To clean a CD, wipe the disc with a
soft cloth outward from the center.
• Use only CDs that have either of the
two Compact Disc Digital Audio marks
as shown below.
• Use only normal, round CDs. If you
insert irregular, non-round, shaped
CDs they may jam in the CD player or
not play properly.
• Check all CDs for cracks, scratches
or warping before playing. CDs that
have cracks, scratches or are warped
may not play properly. Do not use such
discs.
• Avoid touching the recorded (non-printed) surface when handling the disc.
• Store discs in their cases when not in
use.
• Keep discs out of direct sunlight and
do not expose the discs to high temperatures.
• Do not attach labels, write on or apply
chemicals to the surface of the discs.
• If the heater is used in cold weather,
moisture may form on components
inside the CD player. Condensation
may cause the CD player to malfunction. If you think that condensation is
a problem, turn off the CD player for
an hour or so to allow it to dry out and
wipe any damp discs with a soft cloth
to remove the moisture.
• Road shocks may interrupt CD playback.
• Never put a label, tape or scratches on
a disc. These will prevent the disc from
being played.
• When using discs that can be printed
on label surfaces, check the instructions and the warnings of the discs.
Depending on the discs, inserting and
ejecting may not be possible. Using
such discs may result in damage to
this equipment.
Do not attach commercially available
labels or other materials to the discs.
- The discs may warp making the disc
unplayable.
- The labels may come off during
playback and prevent ejection of the
discs, which may result in damage to
the equipment.
CD-R and CD-RW discs
• When CD-R/CD-RW discs are used,
playback is possible only for discs
which have been finalized.
• It may not be possible to play back CDR/CD-RW discs recorded on a music
CD recorder or a personal computer
because of disc characteristics, scratches or dirt on the disc, or dirt, condensation, etc., on the lens of this unit.
• Playback of discs recorded on a personal computer may not be possible,
depending on the application settings
and the environment. Please record
with the correct format. (For details,
contact the manufacturer of the application.)
• Playback of CD-R/CD-RW discs may
become impossible in case of direct
exposure to sunlight, high temperatures, or the storage conditions in the
car.
• Titles and other text information
recorded on a CD-R/CD-RW disc may
not be displayed by this unit (in the
case of audio data (CD-DA)).
• This unit conforms to the track skip
function of the CD-R/CD-RW disc. The
tracks containing the track skip information are skipped automatically (in
case of audio data (CD-DA)).
• If you insert a CD-RW disc into this
unit, time to playback will be longer
than when you insert a conventional
CD or CD-R disc.
• Read the precautions accompanying
the CD-R/CD-RW discs before use.
63
<CRB3881-B/U>63
• Recordings on CD-R/CD-RW can
not be played back using the DDCD
(Double Density CD) system.
• This unit will not play back SACD
(Super Audio CD).
DualDiscs
• DualDiscs are two-sided discs that
have a recordable CD for audio on one
side and a recordable DVD for video on
the other.
• Since the CD side of DualDiscs is not
physically compatible with the general
CD standard, it may not be possible to
play the CD side with this unit.
• Frequent loading and ejecting of a
DualDisc may result in scratches on
the disc. Serious scratches can lead
to playback problems on this unit. In
some cases, a DualDisc may become
stuck in the disc loading slot and will
not eject. To prevent this, we recommend you refrain from using DualDisc
with this unit.
• Please refer to the information from
the disc manufacturer for more
detailed information about DualDiscs.
Error indications
If the CD player does not work, the CD stops suddenly during playback, or a similar problem occurs, an error
indication will appear on the display. The cause of the trouble will be indicated by an error number, and you
should check the corresponding item shown in the table below.
CD CHECK
When the disc is dirty or has been inserted upside-down.
Check the disc.
ERROR 3
There is probably an electrical or mechanical fault in the CD player.
Contact your Scion dealer and ask for repair.
ERROR 4
This appears when there is excess current flow.
Contact your Scion dealer and ask for repair.
WAIT
NO SUPPORT
64
<CRB3881-B/U>64
This appears when the CD player does not work because its temperature is high.
Wait a short while until the vehicle temperature goes down.
This appears when an MP3/WMA/AAC file format is unusual and not supported by
this unit like WAV format recordings.
Please check the MP3/WMA/AAC file format.
When problems occur while the iPod is connected to this unit, a message will appear on the display. Refer to the
table below to identify the problem, then take the suggested corrective action.
ERROR 3
There is probably an electrical or mechanical fault in the iPod.
Please check the iPod.
ERROR 4
This appears when there is excess current flow.
Contact your Scion dealer and ask for repair.
ERROR 6
This appears when an iPod software version is unusual and not supported by this unit.
Please check the iPod software version.
CONNECTION ERROR
NO SONGS
EMPTY
STOP
IPOD ERROR
UPDATE
Communication failure.
Disconnect the cable from the iPod. Once the iPod main menu appears in the iPod
display, connect the cable again.
No songs.
Transfer the songs to the iPod.
There are no songs in the selected list.
Select a list that contains songs.
iPod has stopped.
Select again from list or connect the iPod again.
If the iPod freezes, reset and connect again.
This appears when an unsupported iPod is connected.
Disconnect the device.
This appears when the iPod is unusual and not compatible with this unit.
Please check the iPod compatibility.
65
<CRB3881-B/U>65
When problems occur with the USB portable audio player/USB memory is connected to this unit, a message
will appear on the display. Refer to the table below to identify the problem, then take the suggested corrective
action.
ERROR 3
There is probably an electrical or mechanical fault in the USB portable audio player/
USB memory.
Please check the USB portable audio player/USB memory.
ERROR 4
This appears when there is excess current flow.
Contact your Scion dealer and ask for repair.
ERROR 5
This appears when the USB portable audio player/USB memory is unusual and not
compatible with this unit.
Please check the USB portable audio player/USB memory compatibility.
NO SONGS
This appears when an MP3/WMA/AAC file format is unusual and not supported by
this unit like WAV format recordings.
Please check the MP3/WMA/AAC file format.
CONNECTION ERROR
USB ERROR
66
<CRB3881-B/U>66
Communication failure.
Disconnect the USB portable audio player/USB memory and connect again.
This appears when an unsupported USB portable audio player/USB memory is connected. Disconnect the device.
When problems occur with the XM tuner, a message will appear on the display. Refer to the table below to identify the problem, then take the suggested corrective action.
CK ANTENNA
NO SIGNAL
LOADING
CH OFF AIR
The XM antenna is not connected.
Check whether the XM antenna cable is attached securely.
A short-circuit occurring in the antenna or the surrounding antenna cable.
Make sure that there is nothing unusual with the antenna or antenna cable.
XM signal is too weak at the current location.
Wait until your vehicle reaches a location with a stronger signal.
Unit is acquiring audio or program information.
Wait until the unit has received the information.
The channel you selected is not broadcasting any programming.
Select another channel.
CH UNAUTH
The unit is updating the encryption code.
Wait until the update is finished.
CH UNAVAIL
The unit is receiving a channel with no SID.
The SiriusXM Listener Care Center is also available on the phone, please call (866)-635-2349.
67
<CRB3881-B/U>67
Changing or disconnecting
your battery
About ASL setting
If the battery is changed or disconnected, you cannot setup the ASL
setup option until the vehicle is moving.
Specifications
General
Power source . . . . . . . . . . . . . 13.2 V DC
(10.5 V to 16.0 V allowable)
Grounding system . . . . Negative type
Maximum current consumption . . 15 A
Dimensions (W × H × D)
. . . . . 205.5 mm × 104 mm × 179.6 mm
(80 in.7/8 × 41 in. × 70 in.3/4)
Weight . . . . . . . . . . . . . . . . . . . . 1.76 kg
(3.88016 lbs.)
Audio
Tone controls
(Bass) . . . . . . . . . . . Frequency : 80 Hz
Level : ±10 dB
(Treble) . . . . . . . . . . Frequency : 10 kHz
Level : ±10 dB
Maximum power output . . . . 40 W × 4
Load impedance . . . . . . . . . . . . . . . . 4 Ω
AAC decoding format
. . . iTunes 8.2 or less (extension .m4a)
USB
Specification . . . . . . USB 2.0 full speed
Supply current . . . . . . . . . . . . . . 500 mA
Maximum amount of memory . . . 250 GB
File system . . . . . . . . . . . FAT16, FAT32
MP3 decoding format
. . . . . . . . . . MPEG-1 & 2 Audio Layer 3
WMA decoding format
. . . . . Ver. 7, 7.1, 8, 9, 10, 11 (2ch audio)
(Windows Media Player)
AAC decoding format
. . . iTunes 8.2 or less (extension .m4a)
AM tuner
Frequency range
. . . . . . . . . 530 kHz to 1 710 kHz (10 kHz)
FM tuner
Frequency range
. . . . . . . . . . . . . 87.75 MHz to 107.9 MHz
CD Player
System . . . Compact disc audio system
Usable discs . . . . . . . . . . Compact disc
Signal format
Sampling frequency . . . . . . 44.1 kHz
Number of quantization bits
. . . . . . . . . . . . . . . . . . . . . . . . 16; linear
Number of channels . . . . . . . 2 (stereo)
MP3 decoding format
. . . . . . . . . . MPEG1 & 2 Audio Layer 3
WMA decoding format
. . . . . Ver. 7, 7.1, 8, 9, 10, 11 (2ch audio)
(Windows Media Player)
<KOKZX> <12K00000> <DEH-8228ZT>
68
<CRB3881-B/U>68
<CRB3881-B/U> UC