332689D, 16J750, 16J751, 16W123 Magnum X5, X7

Operation
332689D
Magnum X5, X7, ProX9 Airless Sprayer
EN
For portable spray applications of architectural paints and coatings
Models 16J750, 16J751, 16W123
IMPORTANT SAFETY INSTRUCTIONS
Read all warnings and instructions in this manual
and on the sprayer cord. Save these
instructions.
See page 3 for model series information including
dispense rate, recommended hose length, guns, and
maximum working pressure.
WARNING
FIRE AND EXPLOSION HAZARD: Do not spray or clean
with flammable materials. Use water-based materials only.
ti22085a
ti22143a
ti22084a
Magnum X5
Model: 16J750
Series B
Magnum X7
Model: 16J751
Series B
Magnum ProX9
Model: 16W123
Series A
Table of Contents
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Component Identification X5 . . . . . . . . . . . . . . . . . 8
Component Identification X7 and ProX9 . . . . . . . 10
Grounding and Electric Requirements . . . . . . . . 12
Thermal Overload . . . . . . . . . . . . . . . . . . . . . . . 12
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Trigger Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Pressure Relief Procedure . . . . . . . . . . . . . . . . 13
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Prime and Flush Storage Fluid. . . . . . . . . . . . . 14
Install Tip and Guard on Gun . . . . . . . . . . . . . . 16
Spraying Techniques . . . . . . . . . . . . . . . . . . . . 17
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . 17
Triggering Gun . . . . . . . . . . . . . . . . . . . . . . . . . 17
Aiming Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Unclogging Spray Tip . . . . . . . . . . . . . . . . . . . . 18
Choosing the Correct Tip . . . . . . . . . . . . . . . . . 19
Reversible Tip Selection Chart . . . . . . . . . . . . . 19
2
Shutdown and Cleaning . . . . . . . . . . . . . . . . . . . . 20
Pail Flushing . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Power Flush . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cleaning InstaClean™ Fluid Filter
(ProX9 Only) . . . . . . . . . . . . . . . . . . . . . . . . 24
Cleaning Gun . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Short Term Storage . . . . . . . . . . . . . . . . . . . . . 25
Long Term Storage . . . . . . . . . . . . . . . . . . . . . . 25
Maintenance and Service . . . . . . . . . . . . . . . . . . . 27
Caring for Sprayer . . . . . . . . . . . . . . . . . . . . . . . 27
Paint Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Pump Check Valves . . . . . . . . . . . . . . . . . . . . . 27
Pump Packings . . . . . . . . . . . . . . . . . . . . . . . . . 27
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 34
332689D
Specifications
Specifications
This equipment is not intended for use with flammable or combustible materials used in places such as cabinet
shops or other “factory”, or fixed locations. If you intend to use this equipment in this type of application, you must
comply with NFPA 33 and OSHA requirements for the use of flammable and combustible materials.
Model Name
Series
Maximum
Dispense
Rate lpm
(gpm)
Hose Length and
Diameter
Gun
Model
Maximum Working
Pressure
bar
MPa
PSI
Magnum X5
B
1.02 lpm
(0.27 gpm)
6.4 mm x 7.5 m
(1/4 in. x 25 ft)
SG3
207
21
3000
Magnum X7
B
1.17 lpm
(0.31 gpm)
6.4 mm x 15 m
(1/4 in. X 50 ft)
SG3
207
21
3000
Magnum ProX9
A
1.44 lpm
(0.38 gpm)
6.4 mm x 15 m
(1/4 in. X 50 ft)
SG3
207
21
3000
332689D
3
Warnings
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When
these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific
hazard symbols and warnings not covered in this section may appear throughout the body of this manual where
applicable.
WARNING
WARNING
GROUNDING
This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric current. This product is equipped with a cord
having a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet
that is properly installed and grounded in accordance with all local codes and ordinances.
• Improper installation of the grounding plug is able to result in a risk of electric shock.
• When repair or replacement of the cord or plug is required, do not connect the grounding wire to
either flat blade terminal.
• The wire with insulation having an outer surface that is green with or without yellow stripes is the
grounding wire.
• Check with a qualified electrician or serviceman when the grounding instructions are not completely
understood, or when in doubt as to whether the product is properly grounded.
• Do not modify the plug provided; if it does not fit the outlet, have the proper outlet installed by a
qualified electrician.
• This product is for use on a nominal 230V circuit and has a grounding plug similar to the plug
illustrated in the figure below.
230V
• Only connect the product to an outlet having the same configuration as the plug.
• Do not use an adapter with this product.
Extension Cords:
• Use only an extension cord that has a grounding plug and a receptacle that accepts the plug on the
product.
• Make sure your extension cord is not damaged. If an extension cord is necessary, use 12 AWG
(2.5 mm2) minimum to carry the current that the product draws.
• An undersized cord results in a drop in line voltage and loss of power and overheating.
4
332689D
Warnings
WARNING
WARNING
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent, in work area can ignite or explode. To help prevent fire and explosion:
• Use equipment only in well ventilated area.
• Sprayer generates sparks. When flammable liquids are used near the sprayer or for flushing or
cleaning, keep sprayer at least 20 feet (6 meters) away from explosive vapors.
• Keep work area free of debris, including solvent, rags and gasoline.
• Ground equipment in the work area. See Grounding instructions.
• Stop operation immediately if static sparking occurs or you feel a shock. Do not use equipment
until you identify and correct the problem.
• Keep a working fire extinguisher in the work area.
SKIN INJECTION HAZARD
High-pressure Spray Is Able To Inject Toxins Into The Body And Cause Serious Bodily Injury. In The
Event That Injection Occurs, Get Immediate Surgical Treatment.
• Do Not Aim The Gun At, Or Spray Any Person Or Animal.
• Keep Hands And Other Body Parts Away From The Discharge. For Example, Do Not Try To Stop
Leaks With Any Part Of The Body.
• Always Use The Nozzle Tip Guard. Do Not Spray Without Nozzle Tip Guard In Place.
• Use Graco Nozzle Tips.
• Use Caution When Cleaning And Changing Nozzle Tips. In The Case Where The Nozzle Tip Clogs
While Spraying, Follow The Pressure Relief Procedure For Turning Off The Unit And Relieving
The Pressure Before Removing The Nozzle Tip To Clean.
• Equipment maintains pressure after power is shut off. Do not leave the equipment energized or
under pressure while unattended. Follow the Pressure Relief Procedure before the equipment is
unattended or not in use, and before servicing, cleaning or removing parts.
• Check Hoses And Parts For Signs Of Damage. Replace Any Damaged Hoses Or Parts.
• This System Is Capable Of Producing 3000 Psi. Use Graco Replacement Parts Or Accessories
That Are Rated A Minimum Of 3000 Psi.
• Always Engage The Trigger Lock When Not Spraying. Verify The Trigger Lock Is Functioning
Properly.
• Verify That All Connections Are Secure Before Operating The Unit.
• Know How To Stop The Unit And Bleed Pressure Quickly. Be Thoroughly Familiar With The
Controls.
332689D
5
Warnings
WARNING
WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information
about your material, request MSDS from distributor or retailer.
• Do not leave the work area while equipment is energized or under pressure.
• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine
manufacturer’s replacement parts only.
• Do not alter or modify equipment. Alterations or modifications may void agency approvals and
create safety hazards.
• Make sure all equipment is rated and approved for the environment in which you are using it.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
ELECTRIC SHOCK HAZARD
This equipment must be grounded. Improper grounding, setup, or usage of the system can cause
electric shock.
• Turn off and disconnect power cord before servicing equipment.
• Connect only to grounded electrical outlets.
• Use only 3-wire extension cords.
• Ensure ground prongs are intact on power and extension cords.
• Do not expose to rain. Store indoors.
PRESSURIZED ALUMINUM PARTS HAZARD
Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious
chemical reaction and equipment rupture. Failure to follow this warning can result in death, serious
injury, or property damage.
• Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or
fluids containing such solvents.
• Do not use chlorine bleach.
• Many other fluids may contain chemicals that can react with aluminum. Contact your material
supplier for compatibility.
BURN HAZARD
Equipment surfaces and fluid that is heated can become very hot during operation. To avoid severe
burns:
• Do not touch hot fluid or equipment.
6
332689D
Warnings
WARNING
WARNING
MOVING PARTS HAZARD
Moving parts can pinch, cut or amputate fingers and other body parts.
• Keep clear of moving parts.
• Do not operate equipment with protective guards or covers removed.
• Pressurized equipment can start without warning. Before checking, moving, or servicing
equipment, follow the Pressure Relief Procedure and disconnect all power sources.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
• Read MSDSs to know the specific hazards of the fluids you are using.
• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
PERSONAL PROTECTIVE EQUIPMENT
Wear appropriate protective equipment when in the work area to help prevent serious injury, including
eye injury, hearing loss, inhalation of toxic fumes, and burns. This protective equipment includes but is
not limited to:
• Protective eye wear, and hearing protection.
• Respirators, protective clothing, and gloves as recommended by the fluid and solvent
manufacturer.
332689D
7
Component Identification X5
Component Identification X5
A
Airless spray gun
Dispenses fluid.
B
Power switch
Turns sprayer ON and OFF.
C
Pressure control knob
Increases (clockwise) and decreases (counter-clockwise) fluid pressure in
pump, hose, and spray gun.
C1
Setting Indicator
To select function, align symbol on pressure control knob with setting
indicator, page 13.
D
Pump fluid outlet fitting
Threaded connection for paint hose.
G
Suction tube
Draws fluid from paint pail into pump.
H
Prime tube (with diffuser)
Drains fluid in system during priming and pressure relief.
J
Prime/Spray valve
•
•
•
L
Inlet screen
Prevents debris from entering pump.
M
Paint hose
Transports high-pressure fluid from pump to spray gun.
N
Handle
Used to help transport sprayer.
Q
Tip guard
Reduces risk of fluid injection injury.
R
Reversible spray tip
•
•
PRIME position directs fluid to prime tube.
SPRAY position directs pressurized fluid to paint hose.
Automatically relieves system pressure in overpressure situations.
Atomizes fluid being sprayed, forms spray pattern and controls fluid flow
according to hole size.
Reverse unclogs plugged tips without disassembly.
S
Gun trigger safety lever
(page 13)
Prevents accidental triggering of spray gun.
T
Gun fluid inlet fitting
Threaded connection for paint hose.
U
Power Flush attachment
Connects garden hose to suction tube for power flushing water-base
fluids.
V
Gun fluid filter
Filters fluid entering spray gun to reduce tip clogs.
X
Power cord
Supplies sprayer with electricity
Z
Pump priming button
Manually taps inlet ball to loosen if stuck.
AA
Plug Adapter
Adapts power cord to Australian electrical outlet.
AB
Plug Adapter Retainer
Retains plug adapter to power cord.
8
332689D
Component Identification X5
Component Identification X5
J
Z
AA
AB
N
B
R
H
S
V
G
Q
X
T
L
A
D
M
C1
U
C
ti22144c
332689D
9
Component Identification X7 and ProX9
Component Identification X7 and ProX9
A
Airless spray gun
Dispenses fluid.
B
Power switch
Turns sprayer ON and OFF.
C
Pressure control knob
Increases (clockwise) and decreases (counter-clockwise) fluid pressure in pump,
hose, and spray gun.
C1
Setting Indicator
To select function, align symbol on pressure control knob with setting
indicator, page 13.
D
Pump fluid outlet fitting
Threaded connection for paint hose.
E
InstaClean™ fluid filter
(ProX9 Sprayer Only)
•
•
Filters fluid coming out of pump to reduce tip plugging and improve
finish.
Self cleans only during pressure relief.
F
Power-Piston™ Pump (behind Pumps and pressurizes fluid and delivers it to paint hose.
Easy Access door, not shown)
(ProX9 Sprayer Only)
F1
Easy Access door
(ProX9 Sprayer Only)
Easy Access door permits quick access to outlet valve. To remove door, insert flat
blade of screwdriver into slot on the bottom of the door (as shown on page, 11).
G
Suction tube
Draws fluid from paint pail into pump.
H
Prime tube (with diffuser)
Drains fluid in system during priming and pressure relief.
J
Prime/Spray valve
•
•
•
K
Autoprime
(ProX9 Sprayer Only)
Automatically taps the inlet ball when you turn the sprayer on.
L
Inlet screen
Prevents debris from entering pump.
M
Paint hose
Transports high-pressure fluid from pump to spray gun.
Q
Tip guard
Reduces risk of fluid injection injury.
R
Reversible spray tip
•
•
PRIME position directs fluid to prime tube.
SPRAY position directs pressurized fluid to paint hose.
Automatically relieves system pressure in overpressure situations.
Atomizes fluid being sprayed, forms spray pattern and controls fluid flow
according to hole size.
Reverse unclogs plugged tips without disassembly.
S
Gun trigger safety lever
(page 13)
Prevents accidental triggering of spray gun.
T
Gun fluid inlet fitting
Threaded connection for paint hose.
U
Power Flush attachment
Connects garden hose to suction tube for power flushing water-base
fluids.
V
Gun fluid filter
Filters fluid entering spray gun to reduce tip clogs.
W
Hose wrap Rack
Stows paint hose.
X
Pail hanger
For transporting pail by its handle.
Y
Power Cord
Supplies sprayer with electricity.
Z
Power Flush Adapter
(ProX9 Sprayer Only)
Adapts suction tube (G) to Power Flush attachment (U).
AA
Pump Priming Button
(X7 Sprayer Only)
Manually taps inlet ball to loosen if stuck.
AB
Plug Adapter
Adapts power cord to Australian electrical outlet.
AC
Plug Adapter Retainer
Retains plug adapter to power cord.
10
332689D
Component Identification X7 and ProX9
Component Identification X7 and ProX9
ProX9 Shown
W
ti9346a
B
J
AA
ti22077a
F
K
C
F1
H
Y
G
ti9670a
ti22167a
AC
L
AB
Z
U
X
R
D
A
S
C1
E
M
V
ti9669a
Q
ti22177a
T
ti22176a
332689D
11
Grounding and Electric Requirements
Grounding and Electric Requirements
Fluid supply container: follow local code.
Sprayer must be grounded. Grounding reduces the risk
of static and electric shock by providing an escape wire
for electrical current due to static build up or in the event
of a short circuit.
•
Pails used when flushing: follow local code. Use only
conductive metal pails, placed on a grounded surface
such as concrete. Do not place the pail on a
non-conductive surface, such as paper or cardboard,
which interrupts grounding continuity.
Grounding the metal pail: connect a ground wire to the
pail by clamping one end to pail and other end to ground
such as a water pipe.
The 240 VAC sprayers
require a 220-240 VAC,
50/60 Hz, 10A circuit with a
grounding receptacle.
Maintaining grounding continuity: when flushing or
relieving pressure hold metal part of the spray gun firmly
to the side of a grounded metal pail, then trigger the
gun.
•
Never use an outlet that is not
grounded or an adapter.
•
Do not use the sprayer if the
electrical cord has a damaged ground prong.
•
Only use an extension cord with an undamaged
3-prong plug.
Recommended extension cords for use with this
sprayer:
• 15 m (49.2 ft) 1.0 mm2
• 30 m (98.4 ft) 1.5 mm2
• 50 m (164.0 ft) 2.5 mm2
ti11730a
Spray gun: ground through connection to a properly
grounded fluid hose and pump.
NOTE: Smaller gauge or longer extension cords may
reduce sprayer performance.
ti9207a
Thermal Overload
Motor has a thermal overload switch to shut itself down
if overheated. If unit overheats, allow approximately 45
minutes for unit to cool. Once cool, switch will close and
unit will restart.
To reduce risk of injury from motor starting
unexpectedly when it cools, always turn power
switch OFF if motor shuts down.
12
332689D
Operation
Operation
Trigger Lock
1. Engage trigger lock.
Always engage the trigger lock when you stop spraying
to prevent the gun from being triggered accidentally by
hand or if dropped or bumped.
2. Close the bleed-type master air valve.
3. Disengage the trigger lock.
4. Hold a metal part of the gun firmly to a grounded
metal pail. Trigger the gun to relieve pressure.
5. Engage the trigger lock.
ti8908a
ti8909a
Trigger Locked
Trigger Unlocked
6. Open all fluid drain valves in the system, having a
waste container ready to catch drainage. Leave
drain valve(s) open until you are ready to spray
again.
7. If you suspect the spray tip or hose is clogged or
that pressure has not been fully relieved:
Pressure Relief Procedure
Follow the Pressure Relief Procedure whenever
you see this symbol.
a. VERY SLOWLY loosen tip guard retaining nut
or hose end coupling to relieve pressure gradually.
b. Loosen nut or coupling completely.
This equipment stays pressurized until pressure is
manually relieved. To help prevent serious injury
from pressurized fluid, such as skin injection,
splashing fluid and moving parts, follow the Pressure
Relief Procedure when you stop spraying and before
cleaning, checking, or servicing the equipment.
c.
Clear hose or tip obstruction.
Pressure Control Knob Settings
High Pressure
Spray
Low Pressure Prime/ Rolling
Spray
Clean
ti5597a
NOTE: To select function, align symbol on pressure control knob with setting indicator on sprayer.
332689D
13
Setup
Setup
Prime and Flush Storage Fluid.
4. Turn Pressure Control Knob all the way left
(counter-clockwise) to minimum pressure.
Before you use your sprayer for the first time or begin a
new spraying project, you need to prime the sprayer and
flush the storage fluid out of the sprayer.
•
When spraying water-based materials, flush the
system thoroughly with water. The water flowing out
of prime tube should be clear and solvent-free
before you begin spraying the water-based material.
•
To avoid fluid splashing back on your skin or into
your eyes, always aim gun at inside wall of pail.
ti9344a
5. Make sure the power switch is OFF and the sprayer
is unplugged.
1. Unscrew tip and guard assembly from gun.
ti2810a
6. Separate prime tube (smaller) from suction tube
(larger).
ti9714a
2. Uncoil hose and connect one end to gun. Use two
wrenches to tighten securely.
ti2039a
7. Place prime tube in waste pail.
WASTE
ti9681a
3. Connect other end of hose to sprayer.
ti9652a
8. Submerge suction tube in water
WATER
ti9651a
ti11456a
NOTE: If hose is already connected, make sure connections are tight.
14
332689D
Setup
9. Move Prime/Spray Valve to PRIME.
16. Transfer suction tube to paint pail and submerge
suction tube in paint.
PAINT
ti9346a
ti9653a
17. Turn power switch ON.
10. Plug sprayer in a grounded outlet.
11. Push pump priming button two times.
ti5580a
X5 and X7 Only
ti15972a
12. Turn power switch ON.
ti5580a
13. Align setting indicator with Prime/Clean setting on
Pressure Control knob until pump starts, page 13.
ti9718a
14. When sprayer starts pumping, water and air bubbles will be purged from system. Allow fluid to flow
out of prime tube, into waste pail, for 30 to 60 seconds.
15. Turn power switch OFF.
ti2810a
332689D
15
Setup
18. When you see paint coming out of prime tube:
Install Tip and Guard on Gun
a. Point gun into waste pail.
b. Unlock gun trigger lock.
1. Engage trigger lock.
ti8909a
c.
Pull and hold gun trigger.
ti8908a
d. Move Prime/Spray valve to SPRAY.
2. Verify tip and guard parts are assembled in order
shown.
black rubber gasket and
retaining nut
metal seat
ti9345a
tip
NOTE: Some fluids may prime faster if the Power
Switch is momentarily turned off so the pump can
slow and stop. Repeat several times if necessary.
guard
ti22117a
19. Continue to trigger gun into waste pail until you see
only paint coming out of gun.
Use tip to align seat
in guard
Tip must be pushed
all the way into guard
20. Release trigger. Engage trigger lock.
ti11569a
ti11570a
ti8908a
21. Transfer prime tube to paint pail and clip prime tube
to suction tube.
3. Screw tip and guard assembly on gun. Tighten
retaining nut.
NOTE: Motor stopping indicates pump and hose are
primed with paint. If motor continues to run the sprayer
is not properly primed. To reprime, move Prime/Spray
valve to PRIME and repeat step 18.
ti22116a
16
332689D
Setup
Spraying Techniques
Getting Started
Preventing Excessive Tip Wear
Use a piece of scrap cardboard to practice these basic
spraying techniques before you begin spraying the surface.
•
Spray should be atomized (evenly distributed, no
gaps at edges). Start at low pressure setting,
increase pressure a little at a time until you see a
good spray pattern, without tails.
•
Spray at lowest pressure that atomizes paint.
•
If maximum sprayer pressure is not enough for a
good spray pattern, tip is too worn. See Reversible
Spray Tip Selection Chart, page 19.
•
Hold gun 30 cm (12 in.) from surface and aim
straight at surface. Tilting gun to direct spray angle
causes an uneven finish.
12 in
(30 cm)
thick
even
finish
uneven
finish
thin
good
spray pattern
•
tails- gaps at
edges
thin
thick
thin
ti5592a
NOTE: If tails persist when spraying at the highest pressure, a smaller tip is needed or the material may need to
be thinned.
Adjust Spray Pressure
This sprayer is set up for most airless spraying applications. Details on tip selection, tip wear, coat thickness,
etc. are provided on page 18.
NOTE: Motor only runs when gun is triggered. Sprayer
is designed to stop pumping when gun trigger is
released.
Align setting indicator with function symbol on Pressure
Control knob, page 13.
•
Turning knob to the right (clockwise), increases
pressure at gun.
•
Turning knob to the left (counter-clockwise),
decreases pressure at gun.
332689D
Flex wrist to keep gun pointed straight. Fanning gun
to direct spray at angle causes uneven finish.
even finish
pressure
too low
ti5585a
ti2036a
Triggering Gun
Pull trigger after starting stroke. Release trigger before
end of stroke. Gun must be moving when trigger is
pulled and released.
ti2037a
Aiming Gun
Aim tip of gun at bottom edge of previous stroke, overlapping each stroke by half.
ti2038a
17
Setup
Unclogging Spray Tip
3. Aim gun at piece of scrap or cardboard.
4. Unlock trigger lock. Pull trigger to clear clog.
To avoid fluid splash back
•
Never pull gun trigger when arrow-shaped handle is
between SPRAY and UNCLOG positions.
•
Tip must be pushed all the way into guard.
ti8909a
5. When obstruction is cleared, engage trigger lock
and rotate arrow-shaped handle back to SPRAY
position.
1. To UNCLOG tip obstruction, engage trigger lock.
ti8908a
ti12970a
2. Point arrow-shaped handle backward to UNCLOG
position.
HINT: Point the arrow-shaped handle on the spray tip
forward to SPRAY and backward to UNCLOG obstructions.
ti12971a
Tip Selection
Selecting Tip Hole Size
Tips come in a variety of hole sizes for spraying a range
of fluids. Your sprayer includes an 0.015 in (0.38 mm)
tip for use in most spraying applications. Use the following table to determine the range of recommended tip
hole sizes for each fluid type. If you need a tip other than
the one supplied, see the Reversible Tip Selection
Chart on page 19.
HINT:
As you spray, the tip wears and enlarges. Starting with a
tip hole size smaller than the maximum will allow you to
spray within the rated flow capacity of the sprayer.
Coatings
Tip Hole Size
Stains
0.011 in. (0.28 mm)

0.013 in. (0.33 mm)

0.015 in. (0.38 mm)
0.017 in. (0.43 mm)
0.019 in. (0.48 mm)
18
Enamels
Primers
Interior Paints
Exterior Paints
Acrylics













332689D
Setup
Choosing the Correct Tip
Reversible Tip Selection Chart
Consider coating and surface to be sprayed. Make sure
you use best tip hole size for that coating and best fan
width for that surface.
Tip Part
No.
Fan Width 30 cm
(12 in.) from surface
Hole Size
Tip Hole Size
286311
Tip hole size controls flow rate - the amount of paint that
comes out of the gun.
6 - 8 in.
(152 - 203 mm)
0.011 in.
(0.28 mm)
286411
8 - 10 in.
(203 - 254 mm)
0.011 in.
(0.28 mm)
HINTS:
286313
6 - 8 in.
(152 - 203 mm)
0.013 in.
(0.33 mm)
286413
8 - 10 in.
(203 - 254 mm)
0.013 in.
(0.33 mm)
286415
8 - 10 in.
(203 - 254 mm)
0.015 in.
(0.38 mm)
286515
10 - 12 in.
(254 - 305 mm)
0.015 in.
(0.38 mm)
286417
8 - 10 in.
(203 - 254 mm)
0.017 in.
(0.43 mm)
286517
10 - 12 in.
(254 - 305 mm)
0.017 in.
(0.43 mm)
286619
12 - 14 in.
(305 - 356 mm)
0.019 in.
(0.48 mm)
•
•
Use larger tip hole sizes with thicker coatings and
smaller tip hole sizes with thinner coatings.
Maximum tip hole sizes supported by sprayer:
•
•
•
•
X5: 0.015 in. (0.38 mm)
X7: 0.017 in. (0.43 mm)
ProX9: 0.019 in. (0.48 mm)
Tips wear with use and need periodic replacement.
Fan Width
Fan width is the size of the spray pattern, which determines the area covered with each stroke. Narrower fans
deliver a thicker coat, and wider fans deliver a thinner
coat.
HINTS:
•
Select a fan width best suited to the surface being
sprayed.
•
Wider fans provide better coverage on broad, open
surfaces.
•
Narrower fans provide better control on small, confined surfaces.
Example: For an 8 to 10 in. (203 to 254 mm) fan width
and 0.013 in. (0.33 mm) hole size, order Part No.
286413.
Understanding Tip Number
The last three digits of tip number (i.e.: 286413) contain
information about hole size and fan width on surface
when gun is held 30 cm (12 in.) from surface being
sprayed.
First digit when doubled
= approximate
fan width
413 tip has
8-10 in.
fan width
413 tip has
a 0.013 in.
hole size
ti22118a
Last two digits = tip hole size in thousands of an inch
332689D
19
Shutdown and Cleaning
Shutdown and Cleaning
Pail Flushing
7. Submerge suction tube in water
•
For short term shutdown periods (overnight to two
days) refer to Short Term Storage, page 25.
•
Use only water for flushing. Read Priming and
Flushing Storage Fluid, page 14 or Power Flush,
page 22.
WATER
ti9651b
8. Turn pressure control knob to the Prime/Clean setting.
1. Relieve pressure, page 13.
2. Remove tip and guard assembly from gun and place
in flushing fluid.
3. Place empty waste and water pails side by side.
ti9344a
9. Turn power switch ON.
WATER
WASTE
ti9726b
ti5580a
4. Lift suction tube and prime tube from paint pail. Let
them drain into paint pail for a while.
5. Separate prime tube (smaller) from suction tube
(larger).
10. Flush until approximately 1/3 of the water is emptied
from the pail.
11. Turn power switch OFF.
ti2018a
ti2039a
6. Place prime tube in waste pail.
WASTE
ti9652b
20
332689D
Shutdown and Cleaning
NOTE: Step 12 is for returning paint in hose back to
paint pail. One 50-ft hose holds approximately 1-quart
(1-liter) of paint.
14. Stop triggering gun. Engage the trigger lock.
12. To preserve paint in hose:
a. Point gun into paint pail.
ti8908a
b. Unlock gun trigger lock.
15. Turn Prime/Spray valve to PRIME.
ti8909a
c.
Pull and hold gun trigger.
ti9346a
d. Move Prime/Spray valve to SPRAY.
16. Turn power switch OFF.
ti2018a
ti9345a
17. Clean InstaClean™ Fluid Filter and gun, page 24.
e. Turn power switch ON.
18. Fill unit with Pump Armor™ storage fluid. Read
Long Term Storage, page 25.
ti5580a
f.
Continue to hold gun trigger until you see paint
diluted with water starting to come out of gun.
13. While continuing to trigger gun, quickly move gun to
redirect spray into waste pail. Continue triggering
gun into waste pail until water dispensed from gun is
relatively clear.
WATER
WASTE
ti9745a
332689D
21
Shutdown and Cleaning
Power Flush
10. Unscrew inlet screen from suction tube. Place inlet
screen in waste pail.
Power flushing is a faster method of flushing after spraying water-based coatings.
1. Relieve pressure, page 13.
2. Remove tip and guard assembly from gun and place
in waste pail.
3. Place empty waste and paint pails side by side.
ti2040a
11. Connect garden hose to suction tube with Power
Flush attachment. Leave prime tube in waste pail.
ti9414a
PAINT
WASTE
Adapter
ProX9 only
ti9726b
4. Lift suction tube and prime tube from paint pail. Let
them drain into paint for a while.
ti2042a
12. Turn power switch ON.
5. Place suction and prime tube in waste pail.
6. Turn Pressure Control knob to the Prime/Clean setting.
ti5580a
13. Open valve on Power Flush attachment.
ti9344a
7. Screw Power Flush attachment to garden hose.
Close valve.
close
ti9413a
8. Turn on water. Open valve. Rinse paint off suction
tube, prime tube and inlet screen.
OPEN
14. Circulate water through sprayer, into waste pail, for
20 seconds.
15. Turn power switch OFF.
open
ti9727b
ti2018a
9. Close valve on Power Flush attachment.
close
ti9413a
22
332689D
Shutdown and Cleaning
NOTE: Step 16 is for returning paint in hose back to
paint pail. One 50-ft (15-m) hose holds approximately
1-quart (1-liter) of paint.
18. Stop triggering gun. Engage trigger lock.
16. To preserve paint in hose:
a. Point gun into paint pail.
b. Unlock gun trigger lock.
ti8908a
19. Move prime/spray valve to Prime.
ti8909a
c.
Pull and hold gun trigger.
ti9346a
d. Move Prime/Spray valve to SPRAY.
20. Turn power switch OFF.
ti9345a
ti2018a
e. Turn power switch ON.
21. Turn off garden hose. Close valve on Power Flush
attachment.
close
ti5580a
f.
Continue to hold gun trigger until you see paint
diluted with water starting to come out of gun.
17. While continuing to trigger gun, quickly move gun to
redirect spray into waste pail. Continue triggering
gun into waste pail until water coming out of gun is
relatively clear.
WATER
ti9413a
22. Unscrew Power Flush attachment from suction
tube.
WASTE
ti9745a
ti2047a
23. Clean InstaClean™ Fluid Filter and gun, page 24.
24. Fill unit with Pump Armor™ storage fluid. Read
Long Term Storage, page 25.
332689D
23
Shutdown and Cleaning
Cleaning InstaClean™ Fluid
Filter (ProX9 Only)
Cleaning Gun
•
The InstaClean™ Fluid Filter prevents particles from
entering paint hose. After each use, remove and clean it
to ensure peak performance.
Clean gun fluid filter (d) with water or flushing solvent and a brush every time you flush the system.
Replace gun filter if damaged.
d
1. Relieve pressure, page 13.
2.
ti9668a
a. Disconnect airless spray hose (a) from sprayer
b. Unscrew outlet fitting (b).
c.
•
Remove InstaClean™ Fluid Filter (c).
Remove tip and guard and clean with water or flushing solvent. A soft brush can be used to loosen and
remove dried on material if needed.
b
c
a
ti9347a
3. Check InstaClean™ Fluid Filter (c) for debris. If
needed, clean filter with water and a soft brush.
ti9671a
•
Wipe paint off outside of gun using a soft cloth
moistened with water or flushing solvent.
a. Install closed (square) end of InstaClean™
Fluid Filter (c) in sprayer.
b. Screw outlet fitting (b) into sprayer.
c
ti9347a
b
4. Tighten outlet fitting and reconnect hose (a) to
sprayer. Use two wrenches to tighten securely.
a
ti9674b
24
332689D
Storage
Storage
Short Term Storage
Long Term Storage
(up to 2 days)
(more than 2 days)
1. Relieve pressure, page 13.
Always circulate Pump Armor storage fluid through system after cleaning. Water left in sprayer will corrode and
damage pump. Follow Shutdown and Cleaning, page
20, or Power Flush Cleaning, page 22.
2. Leave suction tube and prime tube in paint pail.
1. Place suction tube in Pump Armor storage fluid bottle and prime tube in waste pail.
ti9353b
WASTE
3. Cover paint pail and hoses tightly with plastic wrap.
ti2057a
2. Move Prime/Spray valve to PRIME.
ti9350a
ti9346a
4.
a. Engage trigger lock.
3. Turn power switch ON.
ti8908a
ti5580a
b. Leave gun attached to hose.
c.
If you have not already cleaned them, remove
tip and guard from gun and clean with water or
flushing solvent. A soft brush can be used to
loosen and remove dried on material if needed.
4. Turn pressure control knob clockwise until the pump
turns on.
ti9671a
d. Wipe paint off outside of gun using a soft cloth
moistened with water or flushing solvent.
332689D
ti9343b
25
Storage
5. When storage fluid comes out of prime tube (5-10
seconds) turn power switch OFF.
6. Move Prime/Spray valve to SPRAY to keep storage
fluid in sprayer during storage.
ti2018a
ti9345a
Stowing Sprayer
NOTICE
•
Before storing sprayer make sure all water is
drained out of sprayer and hoses.
•
Do not allow water to freeze in sprayer or hose.
•
Do not store sprayer under pressure.
1. Screw inlet screen onto suction tube.
3. Secure a plastic bag around suction tube to catch
any drips.
ti5552a
ti9433a
2. Coil hose. Leave it connected to sprayer. Wrap
hose around hose wrap bracket or sprayer stand.
ti12947a
26
4. Store sprayer indoors.
ti22184a
332689D
Maintenance and Service
Maintenance and Service
NOTICE
Protect the internal drive parts of this sprayer from
water. Openings in shroud allow cooling of mechanical
parts and electronics inside. If water gets into these
openings, the sprayer could malfunction or be permanently damaged.
Pump Check Valves
•
Storing in water, inadequate flushing or ingested
debris can cause either of the two check valves to
malfunction.
•
If pump does not prime after 30 seconds, try to
loosen check balls by pushing pump priming button
(X5 and X7 only) or by tapping the inlet valve with a
small wrench as the sprayer is stroking.
Caring for Sprayer
Keep sprayer and all accessories clean and in good
working order.
To avoid overheating motor, keep vent holes in shroud
clear for air flow. Do not cover sprayer while spraying.
ti15972a
X5 and X7 Only
NOTICE
ti14967a
ti9355b
Paint Hoses
Check hose for damage every time you spray. Do not
attempt to repair hose if hose jacket or fittings are damaged. Do not use hoses shorter than 7.5 m (25 ft).
Wrench tighten, using two wrenches.
Tips
•
•
•
Excessive shock will fracture or cause damage to
pump.
NOTE: To verify inlet valve ball is sticking, unscrew
valves from pump and check them.
If sprayer continues to cycle (motor and pump run) after
you release gun trigger, pump valves may be obstructed
or worn. Valve repair kits are available from Graco/Magnum authorized service dealers.
Pump Packings
When pump packings wear, paint
will begin to leak down outside of
pump.
Always clean tips with compatible solvent and brush after spraying.
•
Tips may require replacement
after 57 liters (15 gallons) or they
may last through 227 liters (60 ti2055a
gallons) depending on abrasiveness of paint.
Replace pump packings at
first sign of leaking or additional damage could occur.
•
Purchase a pump repair kit
and install according to
instructions provided with kit.
Do not spray with worn tip.
•
Consult a Graco/MAGNUM
authorized service center.
332689D
ti9356a
27
Troubleshooting
Troubleshooting
Check everything in this Troubleshooting Table before
you bring the sprayer to a Graco/MAGNUM authorized
service center.
Problem
Power switch is on and sprayer is
plugged in, but motor does not run,
and pump does not cycle.
Cause
Solution
Pressure is set at zero pressure.
Turn pressure control knob clockwise
to increase pressure setting.
Motor or control is damaged.
Take sprayer to Graco/MAGNUM
authorized service center.
Electric outlet is not providing power. •
•
Try a different outlet or plug in
something that you know is
working to test outlet.
Reset building circuit breaker or
replace fuse.
Extension cord is damaged.
Replace extension cord. Read
Grounding and Electric Requirements, page 12.
Sprayer power cord is damaged.
Check for broken insulation or wires.
Replace power cord if damaged.
Paint and/or water is frozen or hardened in pump.
Unplug sprayer from outlet. If frozen
do NOT try to start sprayer until it is
completely thawed or you may damage the motor, control board and/or
drivetrain.
Make sure power switch is OFF.
Place sprayer in a warm area for several hours. Then plug in power cord
and turn sprayer ON. Slowly increase
pressure setting to see if motor will
start.
If paint is hardened in sprayer, pump
packings, valves, drivetrain or pressure switch may need to be replaced.
Take sprayer to Graco/MAGNUM
authorized service center.
28
332689D
Troubleshooting
Problem
Pump does not prime.
Cause
Solution
Prime/Spray Valve is in SPRAY posi- Move Prime/Spray Valve to PRIME
tion.
position.
Inlet screen is clogged or suction
tube is not immersed in fluid.
Clean debris off inlet screen and
make sure suction tube is immersed
in fluid.
Pump was not primed with flushing
fluid.
Remove suction tube from paint.
Prime pump with water or solvent-based flushing fluid, page 14.
Inlet valve check ball is stuck.
Remove suction tube and place a
pencil into the inlet section to dislodge the ball, press pump priming
button, or Power Flush sprayer, page
22.
ProX9: AutoPrime may need
replacement. Turn power switch ON
and listen for “tap” in pump. If you do
not hear “tap”, AutoPrime is damaged. Take sprayer to Graco/MAGNUM authorized service center.
Inlet valve check ball or seat is dirty
Remove inlet fitting. Clean or replace
ball and seat.
Outlet valve check ball is stuck.
ProX9: Insert screw driver in slot and
remove Easy-Access™ door, page
11. Unscrew outlet valve with a 3/4
in. socket. Remove and clean
assembly.
X5 and X7: Remove outlet fitting and
clean outlet check ball.
332689D
Suction tube is leaking.
Tighten suction tube connection.
Inspect for cracks or vacuum leaks.
Pump does not prime with fluid.
Remove suction tube from paint.
Prime pump with water or solvent-based flushing fluid.
Fluids are viscous or sticky.
Some fluids may prime faster if the
Power Switch is momentarily turned
off so the pump can slow and stop.
Repeat several times if necessary.
29
Troubleshooting
Problem
Pump cycles but does not build up
pressure.
Pump cycles, but paint only dribbles
or spurts when spray gun is triggered.
30
Cause
Solution
Pump is not primed.
Prime pump.
Inlet screen is clogged.
Clean debris off inlet screen and
make sure suction tube is immersed
in fluid.
Suction tube is not immersed in
paint.
Make sure suction tube is immersed
in paint.
Suction tube is leaking.
Tighten suction tube connection.
Inspect for cracks or vacuum leaks. If
cracked or damaged, replace suction
tube.
Prime/Spray Valve is worn or
obstructed with debris.
Take sprayer to Graco/MAGNUM
authorized service center.
Pump check ball is stuck.
Read Pump does not prime section
in Troubleshooting, page 29
Pressure is set too low.
Slowly turn Pressure Control Knob
clockwise to increase pressure setting which will turn motor on to build
pressure.
Spray tip is clogged.
Unclog spray tip, page 18.
InstaClean™ fluid filter is clogged.
Clean or replace InstaClean™ fluid
filter, page 24.
Spray gun fluid filter is clogged.
Clean or replace gun fluid filter, page
24.
Spray tip is too large or worn.
Replace tip.
332689D
Troubleshooting
Problem
Cause
Pressure is set at maximum but can- Reversible spray tip is in UNCLOG
not achieve a good spray pattern.
position.
Spray tip is too large for sprayer.
Solution
Rotate arrow-shaped handle on
spray tip so it points forward in
SPRAY position, page 18.
Select smaller spray tip.
Spray tip is worn beyond capability of Replace spray tip.
sprayer.
Extension cord is too long or not
heavy enough gauge.
Replace extension cord. Grounding
and Electrical Requirements, page
12.
Spray gun fluid filter is clogged.
Clean or replace spray gun fluid filter,
page 24.
InstaClean™ fluid filter is clogged.
Clean or replace InstaClean™ fluid
filter, page 24.
Inlet screen is clogged.
Clean debris off inlet screen.
Pump valves are worn, or debris is
clogging valve.
Check for worn pump valves.
a. Prime sprayer with paint
b. Trigger gun momentarily.
When trigger is released,
pump should cycle
momentarily and stop. If
pump continues to cycle,
pump valves may be worn.
c. Remove valves and check
for debris.
Spray gun stopped spraying.
When paint is sprayed, it runs down
the wall or sags.
Material is too thick.
Thin material.
Hose is too long (if extra section is
added).
Remove section of hose.
Suction tube is leaking.
Tighten suction tube connection.
Inspect for cracks or vacuum leaks.
Spray tip is clogged.
Unclog spray tip, page 18.
Coat is going on too thick.
Move gun faster.
Choose a tip with smaller hole size.
Choose tip with wider fan.
Make sure gun is far enough from
surface.
When paint is sprayed, coverage is
inadequate.
Coat is going on too thin.
Move gun slower.
Choose tip with larger hole size.
Choose tip with narrower fan.
Make sure gun is close enough to
surface.
332689D
31
Troubleshooting
Problem
Cause
Fan pattern varies dramatically while Pressure control switch is worn and
spraying.
causing excessive pressure variation.
OR
Solution
Take sprayer to Graco/MAGNUM
authorized service center.
Sprayer does not turn on promptly
when resuming spraying.
Cannot trigger spray gun.
Spray gun trigger lock is locked.
Rotate trigger safety lever to unlock
trigger lock, page 13.
Paint is coming out of pressure control switch.
Pressure control switch is worn.
Take sprayer to Graco/MAGNUM
authorized service center.
Prime/Spray valve actuates automat- System is over pressurizing.
ically relieving pressure through
prime tube.
Take sprayer to Graco/MAGNUM
authorized service center.
Paint leaks down outside of pump.
Replace pump packings.
Pump packings are worn.
Motor is hot and runs intermittently. Vent holes in enclosure are plugged
Motor automatically shuts off due to or sprayer is covered.
excessive heat. Damage can occur if
cause is not corrected.
Extension cord is too long or not a
heavy enough gauge.
See Thermal Overload, page 12.
Unregulated electrical generator
being used has excessive voltage.
32
Keep vent holes clear of obstructions
and over spray and keep sprayer
open to air.
Replace extension cord. Read
Grounding and Electrical Requirements, page 12.
Use electrical generator with a
proper voltage regulator. Sprayer
requires 220-240 VAC, 50/60 Hz.
332689D
Technical Data
Technical Data
X5
Working pressure range
X7
ProX9
0-207 BAR, 0-21 Mpa (0-3000 psi)
Electric Motor
4.5A (open frame, universal)
Operating horsepower
Maximum delivery (with tip)
Paint hose
1/2
5/8
7/8
1.02 lpm (.27 gpm)
1.17 lpm (.31 gpm)
1.44 lpm (.38 gpm)
6.4mm X 7.5 m (1/4 in. x 25 ft)
Maximum tip hole size
6.5A
(open frame, permanent magnet DC)
6.4mm X 15 m (1/4 in. x 50 ft)
0.015 in (0.38 mm)
0.017 in (0.43 mm)
0.019 in (0.48 mm)
Weight, Sprayer only
6.0 kg (13.3 lb)
10.6 kg (23.3 lb)
15 kg (33.0 lb)
Weight, Sprayer, hose, & gun
7.5 kg (16.5 lb)
12.7 kg (28 lb)
17.1 kg (37.7 lb)
Dimensions (Upright):
Length
34.8 cm (13.7 in)
49.0 cm (19.3 in)
54 cm (21.3 in)
Width
41.1 cm (16.2 in)
38.9 cm (15.3 in)
43.8 cm (17.3 in)
Height
46.3 cm (18.2 in)
94.0 cm (37.0 in)
94.5 cm (37.2 in)
Dimensions (Folded):
Length
N/A
49.0 cm (19.3 in)
54 cm (21.3 in)
Width
N/A
38.9 cm (15.3 in)
43.8 cm (17.3 in)
Height
N/A
74.2 cm (29.2 in)
74.7 cm (29.4 in)
Power cord
1.0 mm², 3-wire, 1.8 m (6 ft)
Fluid inlet fitting
1/4 npsm external thread
Fluid outlet fitting
3/4 in. internally threaded (standard garden hose)
7/8 - 14 UNF external thread
Inlet screen (on suction tube)
1190 micron (16 mesh)
1680 micron (12 mesh)
Wetted parts, pump and hose
stainless steel, zinc plated carbon steel, brass,
ultra-high molecular weight polyethylene (UHMWPE),
Carbide, Nylon, Aluminum, PVC, polypropylene,
fluroelastomer
stainless steel, zinc plated carbon
steel, brass, leather, ultra-high
molecular weight polyethylene
(UHMWPE), Carbide, Nylon,
Aluminum, PVC, polypropylene,
fluroelastomer
Wetted parts, gun
Generator requirement
Electrical power requirement
aluminum, brass, carbide, nylon, ultra-high molecular weight
polyethylene (UHMWPE), zinc
1500 Watt minimum
220-240V AC 50/60 Hz, I phase, 10A
Storage temperature range
-35° to 71° C (-30° to 160° F)
Operating temperature range
4° to 46° C (40° to 115° F)
Noise **
Sound Pressure
85 dBa
Sound Power
89 dBa
Notes
** Measured while spraying water-based paint, specific gravity 1.36, through a 517 tip at 207 bar, 20.7 Mpa (3000
psi) per ISO 9614-2.
 When pump is stored with non-freezing fluid. Pump damage will occur if water or latex paint freezes in pump.
 Damage to plastic parts may result if impact occurs in low temperature conditions.
 Changes in paint viscosity at very low or very high temperatures can affect sprayer performance.
332689D
33
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs
will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English.
Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures
judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.
TO PLACE AN ORDER or to identify the nearest Graco/MAGNUM distributor, contact us at 1-888-541-9788
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents.
Original instructions. This manual contains English. MM 332689
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2013 Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revision D, March 2016
Download PDF