RP200 Light Module

RP200 Light Module
User Guide
Introduction
The RP200 Light Module works with the Schlage LiNK system as both
a light controller and a signal repeater to help extend the range of the
Schlage Bridge.
FOR INDOOR USE ONLY!
DO NOT use with non-resistive loads, such as fluorescent lighting,
CFL bulbs or motors.
To reduce the risk of electric shock, this product has a grounding
type plug that has a third (grounding) pin. This plug will only fit
into a grounding type power outlet. If the plug does not fit into the
outlet, contact a qualified electrician to install the proper outlet. Do
not change the plug in any way.
Any modification or use other than described may damage the unit
and will void the warranty.
Installation
1. Plug the light module into any available outlet.
•
The light module can be used to control a lamp.
•
The light module repeats the Z-Wave™ signal. In some homes, the
light module must be used to improve communication between the
bridge and the lock. During the online portion of the setup, the system
will determine if it is communicating properly or not. You can move the
light module during online setup if necessary.
•
The light module should be installed into any indoor, three-prong, 120
volt A/C outlet.
2. (Optional) Plug a lamp into the Z-Wave™ (two-prong) side of the
light module.
•
There are two outlets on the light module. One of the outlets has only
two prongs and is labelled with a Z-Wave™ sticker. A lamp (25 watts
minimum and 300 watts maximum) can be controlled by the system if
it is plugged into the Z-Wave™ side of the light module.
•
Use only an incandescent light bulb in the lamp that is plugged into
the light module. DO NOT use a CFL (compact fluorescent light bulb)
or any other kind of electric device.
•
The other outlet has three prongs and can be used simply as a
pass-through outlet (1500 watts maximum). It is not controlled by the
system, and the system is not affected when it is used.
1
2
Max. 300W
Incandescent
Z-Wave™
Side
Pass-through
Side
Enrollment
Double-Click
1. Hold the bridge within 6 feet (1.8 meters) of the light module
throughout all of step 7.
2. Install a fresh 9-volt battery into the bridge.
3. Press and release the plus (+) button on the bridge.
4. Double-click the button on the light module.
Click
+
5. Observe the lights on the bridge. The orange light will blink while
enrollment is taking place. Enrollment is complete when the orange
light becomes solid.
6. Reconnect power and Ethernet to the bridge.
Within 6’
(1.8 m)
+
Remote Control
•
Log into your account at www.schlagelink.com. Click the Lighting &
Automation tab. The light module will be displayed.
•
Download the phone application from www.schlagelink.com.
www.schlagelink.com
Manual Operation
•
Press the button once to turn the light on or off.
•
Press and hold the button to dim.
•
Use the web portal or phone application for remote control.
•
•
The phone application can be downloaded from
www.schlagelink.com, after your account is set up.
The pass-through outlet (1500 watts maximum) is not controlled by
the system, and the system is not affected when it is used.
Click or
Hold
Z-Wave™
Side
Pass-through
Side
Specifications
•
Power 120 VAC, 60 Hz
•
Signal (Frequency) 908.42 MHz
Software Fuse
The RP200 is designed to protect itself against loads that exceed it’s maximum power rating. The application of a load that
exceeds that rating is quickly sensed by the dimmer and it responds by immediately shutting off all power to that load. If
the dimmer doesn’t seem to work, or if it only works momentarily, check to see that the total light wattage doesn’t exceed
the 300W rating of the RP200. If a properly sized load is restored to the dimmer, it can be operated normally once again.
Over-current protection
The RP200 hardware has an over current detection circuit, which is final protection against overload. If the software
fuse should fail to shut down the dimmer when overloaded, backup protection is provided by an internal fuse. This fuse
is not user serviceable. Check your home circuit breakers before concluding that the product must be returned to the
manufacturer for repair at a nominal charge.
FCC NOTICE
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.•
•
Increase the separation between the equipment and receiver.•
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•
•
Consult the dealer or an experienced radio/TV technician for help.•
IC NOTICE
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
About RP200’s Certification
In addition to compliance with product safety standards, the RP200 is also certified to comply with
applicable FCC and IC rules and regulations governing RF and EMI emissions.
Customer Service: (877) 288-7707 (U.S.A. /Canada)
Warranty information is available at part2.schlage.com.
©2010 Schlage Lock Company
light module user guide Rev. 04/10-a
Download PDF