PowerLogic Circuit monitor series 4000

PowerLogic power-monitoring units
Circuit monitor series 4000
Technical data sheet
2009
Power-monitoring units
Circuit Monitor Series 4000
Functions and characteristics
PE86140
DB119008
The PowerLogic Circuit Monitor Series 4000 offers high-performance digital
instrumentation, data acquisition and control capabilities. The products can integrate
easily in power monitoring and control systems due to their optional Ethernet
connections and embedded web server. They are Transparent Ready.
These devices are designed for applications where power quality and availability are
critical factors. They are generally used at service entrances and interconnection
points or on circuits feeding sensitive equipment. Due to their very wide range of
features, including transient detection (CM4000T only), it is possible to rapidly solve
problems related to poor power quality. EN 50160 compliance checking capability
makes these products ideal to meet new needs related to market deregulation.
The Circuit Monitor Series 4000 is available in two versions:
b CM4250, with detection of voltage sags, swells and other power quality indices
b CM4000T, with detection of voltage sags and swells together with transient
detection and flicker measurements.
Applications
Panel instrumentation.
Sub-billing / cost allocation.
Remote monitoring of an electrical installation.
Extensive power-quality monitoring.
Contract and load curve optimisation.
EN 50160 electrical supply compliance checking.
Metering of other utilities.
Main characteristics
CM4000 + vacuum fluorescent display (VFD).
Disturbance direction detection
Indication of whether the source of a specific power quality event is upstream or
downstream from the meter.
Power quality summary
Consolidation of all the power quality characteristics into a single trendable index.
Adaptive waveform capture
Capture of long-duration events.
Shift energy summary
Indication of energy usage per shift up to three shifts a day.
Detection and capture of voltage sags and swells
Fast identification of problems causing production shutdown.
Detection and capture of short transients less than 1 µs
(optional, CM4000T only)
Identification of problems due to short disturbances, e.g. switching of capacitors, etc.
Flicker evaluation based on IEC 61000-4-15 and IEEE 1453 (CM4000T only)
Measurement of rapid voltage variations.
Electrical quality checking in compliance with EN 50160
Fast standardised check on the quality of the electricity supplied.
Detection of major waveform changes
Detection of phase switching phenomena (for example during the transfer of a highspeed static switch) not detected by classical threshold-based alarms.
Ultra-fast recording of electrical parameters every 100 ms or every cycle
Preventive maintenance: acquisition of a motor startup curve, etc.
Trend curves and short-term forecasting
Rapid trending and forecasting of upcoming values for better decision making.
Automatic alarm setting
Alarm setpoint learning feature for optimum threshold settings.
Up to 32 Mbytes of memory (16 Mbytes standard)
For archiving of data and waveforms.
Ethernet 10/100 Mbits/s card and server for HTML pages
(with optional Ethernet card)
Rapid data transfers over an intranet or the internet, simply using a web browser.
Alarm notification via email
High-priority alarms sent directly to the user’s PC.
Instant notification of power quality events by email.
Up to 25 inputs/outputs to monitor the electrical installation
(with optional I/O cards)
Status of circuit breakers, as well as metering of other commodities, e.g. gas, water, etc.
IEC 62053-22 and ANSI C12.20 Class 0.2S for energy
Verification of consumption and load curves.
Power-monitoring units
Circuit Monitor Series 4000
0
Functions and characteristics (cont.)
Part numbers
Circuit Monitor Series 4000
Square D brand
Circuit Monitor CM4250
Circuit Monitor CM4000T
CM4250
CM4000T
Merlin Gerin brand
Circuit Monitor CM4250
Circuit Monitor CM4000T
CM4250MG
CM4000TMG
Options
See page 432E2010.indd/4
Selection guide
DB108168
General
Use on LV and HV systems
Current and voltage accuracy
Energy and power accuracy
Nbr of samples/cycle or sample frequency
CM4250
CM4000T
b
0.07 %
0.2 %
512
b
0.07 %
0.2 %
5 MHz
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
63
255
b
b
b
b
b
b
b
63
255
b
b
b
b
b
b
b
b
Instantaneous rms values
Current, voltage, frequency
Active, reactive, apparent power
Power factor
Total and per phase
Total and per phase
Energy values
Active, reactive, apparent energy
Settable accumulation modes
Demand values
CM4000.
1 Current/voltage module.
2 Control power-supply connector.
3 Maintenance LED indicator.
4 Power LED indicator.
5 RS 485 port with transmit and receive LED indicators.
6 Display communication port.
7 Slots for optional cards.
8 RS 232 port with transmit and receive LED indicators.
9 KYZ pulse output.
10Sealable access door.
Current
Present and max. values
Active, reactive, apparent power
Present and max. values
Predicted active, reactive, apparent power
Synchronisation of the measurement window
Setting of calculation mode
Block, sliding
Power quality measurements
Interharmonics
Harmonic distortion
Individual harmonics
Current and voltage
Via monitor
Via SMS
Waveform capture
Detection of voltage swells and sags
Adaptive waveform capture (up to 64 s)
Detection and capture of transients (< 1 µs)
Flicker
Fast acquisition of 100 ms or cycle by cycle data
EN 50160 compliance checking (1)
Programmable (logic and math functions)
Data recording
E87306
Min/max of instantaneous values
Data logs
Event logs
Trending/forecasting
Alarms (optional automatic alarm setting)
Alarm notification via email
SER (Sequence of Event Recording)
Time stamping
GPS synchronisation (1 ms)
Memory expandable up to
b
b
b
b
b
b
b
b
b
b
ECC21 option
b
b
b
b
IOC44 option
32 Mbytes
32 Mbytes
Display and I/O
Disturbance waveform capture: detection of a voltage sag.
Display
Multilingual: English, French, Spanish, German, Italian, Polish
Wiring self-test
Pulse output
Maximum number of I/Os
Input metering capability (number of channels)
Direct voltage connection
CMDLC or CMDVF option
b
b
b
b
b
b
25
25
10
10
690 V
600 V
Communication
RS 485 port
2/4 wires
2/4 wires
b
b
RS 232 port
b
b
Modbus protocol
Ethernet card (Modbus/TCP/IP protocol)
ECC21 option
HTML-page web server
ECC21 option
Ethernet gateway for third-party products
ECC21 option
(1) Except for interharmonics, signalling voltages, flicker and transients.
Power-monitoring units
Circuit Monitor Series 4000
Functions and characteristics (cont.)
The Circuit Monitor has two optional display units, an LCD display and a vacuum
fluorescent display (VFD). They may be used for local circuit-monitor setup and
operation.
PE86143
CMDLC display
Back-lit LCD display with four lines and 20 characters per line. The display unit has
four navigation buttons, a contrast button and a red alarm LED.
It connects to the Circuit Monitor via a CAB12 cable, 4.2 metres long, supplied with
the display.
Part numbers
LCD display supplied with the CAB12 cable
Connection cables:
1.25 m (4 ft)
Circuit Monitor <-> display
3.65 m (12 ft)
9.14 m (30 ft)
Merlin Gerin brand
CMDLCMG
CAB4
CAB12
CAB30
Square D brand
CMDLC
CAB4
CAB12
CAB30
PE86142
CMDVF display
Vacuum fluorescent display (VFD) with four lines and 20 characters per line.
The display unit has four navigation buttons, a contrast button, a red alarm LED.
The display comes with a cable for connection to the Circuit Monitor (CAB12 cable,
4.2 m long).
Part numbers
VFD supplied with the CAB12 cable
Connection cables:
1.25 m (4 ft)
Circuit Monitor <-> display
3.65 m (12 ft)
9.14 m (30 ft)
E87288
1
2
3
4
5
6
7
Display.
Display screen.
Alarm LED.
Arrow buttons.
Menu button.
Proximity sensor (VFD display only).
Enter button.
Contrast button.
Merlin Gerin brand
CMDVFMG
CAB4
CAB12
CAB30
Square D brand
CMDVF
CAB4
CAB12
CAB30
0
Power-monitoring units
Circuit Monitor Series 4000
0
059141
Functions and characteristics (cont.)
Ethernet ECC21 communication card
The ECC21 is an optional Ethernet communication card. It may be installed in the
slot in the Circuit Monitor intended for options. It has two main functions:
b equip the Circuit Monitor with a fast Ethernet connection over a 10/100 Mbits/s
copper link or a 100 Mbits/s fiber-optic link
b serve as an Ethernet gateway for devices daisy chained to its RS 485 ModBus
port.
The ECC21 card also includes a server for six HTML pages that may be consulted
by a standard web browser. These pages can be customised using WPG software
and display information from the host Circuit Monitor and/or devices connected to its
ModBus port.
Part number
059217
Ethernet communication card
ECC21
CVM42 current/voltage module
This is the CM4250 acquisition module for currents and voltages. It is supplied
already installed on the CM4250. If the Circuit Monitor must be recalibrated, this is
the only module requiring recalibration. It may be installed and removed in the field.
This module may also be replaced in the field by a CVMT module to transform a
CM4250 into a CM4000T.
Part number
Current/voltage module for CM4250
CVM42
CVMT current-voltage module
This is the CM4000T acquisition module for currents and voltages, i.e. it is suitable
for the detection of transient phenomena with a 5 MHz voltage-sampling rate. Similar
to the CVM42, it may be installed and removed in the field. It is supplied already
installed on the CM4000T.
Part number
CM4000T current/voltage module
CVMT
Memory extension kit
These kits make it possible to extend the Circuit Monitor memory to 16 MB or 32 MB.
Part numbers
32 MB kit
CM4MEM32M
Power-monitoring units
Circuit Monitor Series 4000
0
Functions and characteristics (cont.)
Input/output blocks may be added to the Circuit Monitor to:
b monitor the electrical installation, notably the status of the circuit breakers, and
check discrimination between protection devices
b measure the consumption of other commodities by counting the pulses sent by
water or gas meters
b measure the temperature of the transformers
b transmit parameters over analog channels to other systems
b etc.
The Circuit Monitor may be equipped with a total of 25 optional digital or analog input/
outputs.
These input/outputs may be added in two different manners:
b either using an IOC44 card
b or the IOX input/output extender module and individual input/output modules that
connect to the extender.
All these options may be installed in the field. Status changes on the digital inputs
are time-stamped to within the millisecond.
059142
IOC44 card
This is an input/output card equipped with:
b 4 digital inputs 20 - 138 V AC/DC
b 4 digital outputs, including 3 relay outputs and a static output that may be
programmed as a pulse output. It may be installed in the option-card slots of the
Circuit Monitor.
There are three possible configurations:
b 1 IOC44 card
b 2 IOC44 cards
b 1 IOC44 card and 1 Ethernet ECC21 card.
Part number
IOC44
IOC44 card
059145
IOX input/output extender
The IOX input/output extender may be equipped with up to eight plug-in input
or output modules. The entire unit connects to the side of the Circuit Monitor.
The input/output modules may be digital or analog.
Three pre-equipped versions may be ordered directly, the IOX08, IOX0404 and
IOX2411. Other versions may be user prepared by ordering an empty IOX extender
and separate I/O modules (see the section on I/O Modules for selection). In this case,
the IOX extender may be equipped with up to a maximum of four analog modules.
Description
IOX extender
IOX extender equipped with two input/output modules.
IOX08 extender
059144
IOX0404 extender
IOX2411 extender
Empty extender with eight slots for separate input and/or
output modules, digital or analog, with however a
maximum of four analog modules.
IOX extender equipped with:
8 digital input modules 120 V AC
IOX extender equipped with:
4 digital input modules 120 V AC
4 analog input modules 4-20 mA
IOX extender equipped with:
2 digital output modules 60 V DC
4 digital input modules 32 V DC
1 analog output module 4-20 mA
1 analog input module 0-5 V
Part numbers
IOX2411 pre-equipped extender module.
IOX extender
IOX08 extender
IOX0404 extender
IOX2411 extender
IOX
IOX08
IOX0404
IOX2411
Power-monitoring units
Circuit Monitor Series 4000
0
059160
Functions and characteristics (cont.)
Input/output modules
The input/output modules are installed in the slots of the IOX extender. One module
corresponds to either one input or one output. A number of versions are available,
digital and analog inputs and outputs, and different voltage levels.
Description
DI120AC module
DI240AC module
DI32DC module
DO120AC module
DO240AC module
DO200DC module
DO60DC module
AI05 module
AI420 module
AO420 module
One digital input 120 V AC
One digital input 240 V AC
One polarised digital input 32 V DC, switching time 0.2 ms
One digital output 120 V AC, 3.5 A max
One digital output 240 V AC, 3.5 A max
One digital output 200 V DC, 3.5 A max
One digital output 60 V DC, 3.5 A max
One analog input 0-5 V DC
One analog input 4-20 mA
One analog output 4-20 mA, max. load 250 W
Part numbers
DI120AC module
DI240AC module
DI32DC module
DO120AC module
DO240AC module
DO200DC module
DO60DC module
AI05 module
AI420 module
AO420 module
DI120AC
DI240AC
DI32DC
DO120AC
DO240AC
DO200DC
DO60DC
AI05
AI420
AO420
Power-monitoring units
Circuit Monitor Series 4000
0
Functions and characteristics (cont.)
Electrical characteristics
PE86141
Type of measurement
Measurement
accuracy
Current and voltage
Power
Frequency
Power factor
Energy:
CM4250/CM4000T
Data update rate
Input-voltage
Measured voltage
characteristics
CM4000 + options: ECC21, IOC44 and IOX2411.
Input-current
characteristics
Power supply
Input/outputs
Measurement range
Impedance
Frequency measurement
range
CT ratings
Measurement range
CM4250/CM4000T
Permissible overload
Impedance
Load
AC
DC
Ride-through time
Pulse output
IOC44 card (optional)
IOX extender (optional)
IOX08 (optional)
IOX0404 (optional) (1)
IOX2411 (optional) (1)
True rms up to the 255th harmonic
On three-phase AC system (3P, 3P + N)
Up to 512 samples per cycle
Up to 5 MHz for transient events (CM4000T only)
±0.04 % of reading + ±0.025 % of full scale
±0.075 % of reading + ±0.025 % of full scale
±0.01 Hz from 45 to 67 Hz
±0.1 Hz from 350 to 450 Hz
±0.002 from 0.5 leading to 0.5 lagging
IEC 62053-22 and ANSI C12.20 Class 0.2S
1 s in normal mode
0 to 600 V AC on CM4000T (direct)
0 to 690 V AC on CM4250 (direct)
0 to 1200 kV AC (with external VT)
0 to 1.5 Un
> 2 MW
45 to 67 Hz and 350 to 450 Hz
Adjustable from 5 A to 30 000 A
5 mA to 10 A
15 A continuous
50 A for 10 seconds per hour
500 A for 1 second per hour
< 0.1 W
< 0.15 VA
100 to 275 V AC (±10 %), 50 VA
125 to 250 V DC (±20 %), 30 W
100 ms at 120 V DC
Static output (240 V AC max, 96 mA max)
4 digital inputs (20-138 V AC/DC),
3 relay outputs (5 A to 240 V AC)
1 static output (96 mA max to 240 V AC)
Slots for 8 I/Os
8 digital inputs 120 V AC
4 dig. inputs 120 V AC, 4 analog outputs 4-20 mA
2 dig. outputs 120 V AC, 4 dig. inputs 32 V DC,
1 analog input 0-5 V, 1 analog output 4-20 mA
Mechanical characteristics
Weight
IP degree of protection (IEC 60529)
Dimensions
Without IOX accessory
CM4250/
With IOX accessory
CM4000T
1.9 kg
IP52
235.5 x 165.6 x 133.1 mm
235.5 x 216.3 x 133.1 mm
Environmental conditions
Operating
temperature
Circuit Monitor
CMDLC display
CMDVF display
CM + displays
Storage
temperature
Humidity rating
Pollution degree
Installation
CVM42
category
CVMT
Dielectric withstand
Electromagnetic compatibility
Electrostatic discharge
Immunity to radiated fields
Immunity to fast transients
Immunity to impulse waves
Conducted and radiated emissions
-25 °C to +70 °C
-20 °C to +60 °C
-20 °C to +70 °C
-40 °C to +85 °C
5 to 95 % RH at 40 °C
2
IV
II
As per EN 61010, UL508, CSA C22.2-2-4-M1987
Level 3 (IEC 61000-4-2)
Level 3 (IEC 61000-4-3)
Level 3 (IEC 61000-4-4)
Level 4 (IEC 61000-4-5)
e industrial envir./FCC part 15 class A
Safety
Europe
e, as per CEI 61010
USA and Canada
UL508 and CSA C22.2-2-4-M1987
(1) Operating limits: 0° C to +60 °C. Storage limits: -25 °C to +85 °C.
Power-monitoring units
Circuit Monitor Series 4000
0
Functions and characteristics (cont.)
Communication
2/4 wires, up to 38400 bauds, Modbus
Up to 38400 bauds, Modbus, direct connection to a PC
or modem
Ethernet ECC21 card with HTML server (optional) (1)
Copper Ethernet link
10/100 BaseTX, RJ45 connector, 100 m link
Fiber-optic Ethernet link
100 Base FX, LC duplex connector, 1300 nm, FO
multimode with gradient index 62.5/125 µm or 50/125 µm,
2000 m link
Protocol
Modbus/TCP/IP
Gateway function for products
Master Modbus port, 31 daisy-chained slaves,
connected to the ECC21
63 with repeater, 2/4 wires, 1200 to 38400 bauds,
also compatible with the PowerLogic protocol
HTML server
1 standard page, 5 customisable pages
E87307
RS 485 port (1)
RS 232 port (1)
Firmware characteristics
E87308
Adaptive waveform capture: transformer inrush current.
14 data logs
Up to 96 different parameters, factory-set logs ready
to use
One 100 ms data log
One 20 ms (50 Hz) or 16 ms (60 Hz)
data log
One min/max log
One min/max/avg. log
Parameters recorded every 100 ms for events
Parameters recorded every 20 ms or 16 ms for events
One event log
Trend curves
Forecasting
Waveform captures
Adaptive waveform capture: motor start, rms value.
E87309
Alarms
Example CM4250 HTML page showing instantaneous values.
Memory
Firmware update
Min/max/avg. values recorded for 23 parameters at
regular intervals from 1 to 1440 minutes
Time stamping to 1 ms, synchro. 1 ms by GPS
Four trend curves: 1 minute, 1 hour, 1 day and 1 month.
Min./max./avg. values recorded for eight parameters:
- every second for one minute for the 1-minute curve
- every minute for one hour for the 1-hour curve
- every hour for one day for the 1-day curve
- every day for one month for the 1-month curve
Forecasting of the values for the eight parameters
for the next four hours and next four days
Standard: manual launch, 1 cycle, 512 samples, 255th
harmonic
Disturbance: manual launch or by alarm, adjustable from
512 samples/cycle over 28 cycles to 16 samples/cycle
over 915 cycles, response time less than 0.5 cycle,
number of cycles before alarm settable from 2 to 10
Adaptive: manual launch or by alarm, adjustable from
512 samples/cycle over 8 seconds to 16 samples/cycle
over 264 seconds, capture takes place during a set
duration or as long as an alarm is active (to save memory),
number of cycles before alarm settable from 2 to 10
Transient: voltage sampling at 5 MHz (83 333 samples/
cycle) over 2 ms to capture transient peaks < 1 µs
Threshold alarms:
- adjustable pickup and dropout setpoints and time delays,
numerous activation levels possible for a given type of
alarm
- 4 priority levels
- 4 response times: standard 1 s, fast 100 ms,
disturbance < 1/2 cycle, transient < 1µs
- boolean combination of four alarms is possible using the
operators NAND, OR, NOR and XOR
Automatic alarm setting: after a learning phase, the alarm
thresholds are set automatically. The alarms will trip in the
event of drift with respect to reference values determined
during the learning period.
Digital alarms: logic input transitions
Waveform alarms: alarm tripping by a special algorithm
when the current or voltage waveform is distorted beyond
an adjustable level. Makes it possible to detect
disturbances that cannot be detected by classical
threshold alarms (e.g. phase switching).
8 Mbytes standard, expandable up to 32 Mbytes
Update via the communication ports
Display characteristics
CMDLC (optional)
Back lit LCD
CMDVF (optional)
Vacuum fluorescent display (VFD) with IR port
Languages
English, French, Spanish, German, Italian, Polish
(1) All the communication ports may be used simultaneously.
Circuit Monitor Series 4000
Power-monitoring units
Installation and connection
E94394
E94392
E94393
CM4250 / CM4000T dimensions
DB108169
Mounting on a backplate
10
Circuit Monitor Series 4000
Power-monitoring units
Installation and connection (cont.)
DB108005
DB108006
DB108007
Mounting possibilities
Vertical mounting.
Horizontal mounting.
E87285
E87286
CMDLC/CMDVF dimensions
E94377
Mounting on a backplate
11
Power-monitoring units
Circuit Monitor Series 4000
Installation and connection (cont.)
DB108008
3-wire connection with 2 CTs and no PT
DB108009
4-wire connection with 4 CTs and 3PTs
12
Circuit Monitor Series 4000
Power-monitoring units
Installation and connection (cont.)
IOX input/output extender
DB112615
DB111311
Ethernet ECC21 communication card
or
(1)
(1)
DB112617
IOC44 input/output card
13
PLSED303025EN © 2007 - Schneider Electric - All rights reserved
Schneider Electric
35 Rue Joseph Monier, CS 30323
92506 Rueil Malmaison Cedex
Tel : +33 (0)1 41 29 70 00
http://www.schneider-electric.com
http://www.PowerLogic.com
PLSED303025EN
As standards, specifications and designs develop from time to time, always ask for confirmation of the
information given in this publication. PowerLogic, ION, ION Enterprise, MeterM@il and Modbus are
either trademarks or registered trademarks of Schneider Electric.
Printed on recycled paper
Publishing : Schneider Electric
Production : Schneider Electric PMC
Printing : Imprimerie du Pont de Claix - made in France
11-2008
Download PDF