SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Sienna
BY: SHERWOOD INDUSTRIES LTD
OWNER’S MANUAL
WHAT TO DO IF YOU SMELL GAS
• Open windows/extinguish any open
flame.
• Do not try to light any appliance.
• Do not touch any electrical switch or
use any phone in your building.
• Immediately call your gas supplier
from a neighbour’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas supplier,
call the fire department.
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapours and liquids in the
vicinity of this or any other appliance.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless a
certified kit is used.
WARNING
If the information in this manual is not followed exactly, a fire or explosion may result
causing property damage, personal injury or loss of life. Installation and service must be
performed by a qualified installer, service agency or the gas supplier.
Massachusetts installations (Warning): This product must be installed by a licensed
plumber or gas fitter when installed within the Commonwealth of Massachusetts.
Other Massachusetts code requirements: Flexible connector must not be longer than
36in., a shut off valve must be installed; only direct vent sealed combustion products
are approved for bedrooms/bathrooms. A carbon monoxide detector is required in all
rooms containing gas fired direct vent appliances.
50-1096
Safety Precautions
FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER,
PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:
• All ENVIRO gas-fired appliances must be installed
in accordance with their instructions. Carefully read all
the instructions in this manual first. Consult the building
authority having jurisdiction to determine the need for
a permit prior to commencing the installation.
• NOTE: Failure to follow these instructions could
cause a malfunction of the fireplace, which could
result in death, serious bodily injury, and/or property
damage.
• Failure to follow these instructions may also void
your fire insurance and/or warranty.
GENERAL
• Installation and repair should be done by a
qualified service person. The appliance should be
inspected before the first use and, at least, annually
by a qualified service person. More frequent
cleaning may be required due to excessive lint from
carpeting, bedding material, etc. It is imperative the
control compartments, burners and circulating air
passageways of the appliance be kept clean.
• Due to high temperatures, the appliance should
be located out of high traffic areas and away from
furniture and draperies.
Children and adults should be alerted to the
hazards of high surface temperatures and
should stay away to avoid burn or clothing
ignition.
• Young children should be carefully supervised
when in the same room as the appliance.
• Clothing or other flammable materials should not
be placed on or near the appliance.
FOR YOUR SAFETY
• Installation and service must be performed by a
qualified installer, service agency or gas supplier.
• This installation must conform to local codes or, in
the absence of local codes, to the current CAN/CGAB149 installation code (Canada) or National Fuel Gas
Code ANSI Z223.1.2 (USA)
2
• To prevent injury, do not allow anyone who is
unfamiliar with the stove to operate it.
• To prevent injury, if the pilot or pilot and
burners have gone out on their own, open the
glass door and wait 5 minutes to air out before
attempting to re-light the stove.
• Always keep the area around these appliances
clear of combustible material, gasoline and other
flammable liquids and vapours.
• These appliances should not be used as a drying
rack for clothing or for hanging Christmas stockings/
decorations.
• Due to the paint curing on the stove, a faint odor
and slight smoking will likely be noticed when the
stove is first used. Open a window until the smoking
stops.
Always connect this gas stove to a vent system and
vent to the outside of the building envelope. Never
vent to another room or inside the building. Make sure
the specified vent pipe is used, properly sized and of
adequate height to provide sufficient draft. Inspect
the venting system annually for blockage and signs of
deterioration.
WARNING: Failure to position the parts in accordance
with the diagrams in this booklet, or failure to use only
parts specifically approved with this appliance, may
result in property damage or personal injury.
WARNING: Do not operate with the glass front
removed, cracked or broken. Replacement of the
glass should be done by a licensed or qualified service
person.
• Never use solid fuels such as wood, paper,
cardboard, coal, or any flammable liquids, etc., in this
appliance.
• Do not use this heater if any part has been under
water. Immediately call a qualified service technician
to inspect the heater and to replace any part of the
control or gas control systems that have been under
water.
• Do not abuse the glass by striking it or slamming
the door shut.
Table of Contents
Safety Precautions.....................................................................................................2
Table of Contents......................................................................................................3
Codes And Approvals.................................................................................................4
Specifications............................................................................................................5
Rating Label Location......................................................................................5
Dimensions....................................................................................................5
Operating Instructions...............................................................................................7
Pilot Lighting Instructions................................................................................7
Remote Controls - Optional.............................................................................7
Burner Lighting...............................................................................................7
Turn Off Unit..................................................................................................8
Blower Speed.................................................................................................8
Normal Sounds During Operation.....................................................................8
Adjusting Venturi Air Settings..........................................................................8
Maintenance And Service...........................................................................................9
Cleaning The Glass.........................................................................................9
Cleaning The Firebox......................................................................................9
Replacing The Glass.......................................................................................9
Cleaning The Plated Surfaces..........................................................................9
Glass Door Removal......................................................................................10
Burner & Blower Removal..............................................................................10
Fuel Conversion............................................................................................11
Initial Installation.....................................................................................................13
Clearances to Combustibles...........................................................................13
Minimum Fireplace Size.................................................................................14
B-Vent Model................................................................................................14
Automatic Flue Gas Spill Switch - B-Vent Model Only........................................14
Direct Vent Model.........................................................................................15
Preparing Your Sienna For Installation............................................................15
Venting Fireplace Inserts...............................................................................16
Electrical Requirements.................................................................................17
Gas Line Connection......................................................................................18
Converting A Direct Vent Fireplace To A B-Vent Fireplace.................................19
Secondary Installation..............................................................................................20
Installation of Surround Panel........................................................................20
Log Set and Ember Installation......................................................................21
Removing The Brick Panel.............................................................................24
Trouble Shooting.....................................................................................................25
Parts List- Unit Components.....................................................................................26
Parts Diagram - Components....................................................................................27
Parts Diagram - Burner.............................................................................................28
Parts List - Options..................................................................................................29
Parts Diagram - Options...........................................................................................30
Warranty.................................................................................................................31
Installation Data Sheet.............................................................................................32
3
Codes And Approvals
DIRECT VENT: This type is identified by the suffix DV. This appliance draws all of its air for combustion from
outside the dwelling, through a specially designed vent pipe system.
This appliance has been tested and approved for installations from 0 feet to 4500 feet (1372 m) above sea level.
BV: This Vented appliance draws all of its combustion air from the dwelling and must be vented using listed B or L
vent. May also be vented through a conventional chimney using a chimney liner kit.
This appliance has been tested and approved for installations from 0 feet to 4500 feet (1372 m) above sea level.
In the USA: The appliance may be installed at higher altitudes. Please refer to your American Gas Association
guidelines which state: the sea level rated input of Gas Designed Appliances installed at elevations above 2000
(610 m) feet is to be reduced 4% for each 1000 feet (305 m) above sea level. Refer also to local authorities or
codes which have jurisdiction in your area regarding the de-rate guidelines.
In Canada: When the appliance is installed at elevations above 4500 feet (1372 m), the certified high altitude
rating shall be reduced at the rate of 4% for each additional 1000 feet (305 m).
•
This appliance has been tested by INTERTEK (Warnock Hersey) and found to comply with the established
VENTED GAS FIREPLACE HEATER standards in CANADA and the USA as follows:
VENTED GAS FIREPLACE HEATER (SIENNA BV/DV; NG/LPG)
TESTED TO: ANSI Z21.88a-2003/CSA 2.33a-2003 VENTED GAS FIREPLACE HEATERS
CAN/CGA 2.17-M91 GAS FIRED APPLIANCES FOR HIGH ALTITUDES
CSA P.4.1-02 TESTING METHOD FOR MEASURING ANNUAL FIREPLACE EFFICIENCY
This ENVIRO SIENNA Fireplace:
• Has been certified for use with either natural or propane gases. (See rating
label.)
• Is not for use with solid fuels.
• Is approved for bedroom or bed sitting room. (IN CANADA: must be installed
with a listed wall thermostat. IN USA: see current ANSI Z223.1 for installation
instructions.)
• Must be installed in accordance with local codes. If none exist, use current
installation code CAN/CGA B149 in Canada or ANSI Z223.1/NFPA 54 in the USA.
• Must be properly connected to an approved venting system and not connected to
a chimney flue serving a separate solid-fuel burning appliance.
• Is not approved for closet or recessed installations.
IMPORTANT NOTICE (Regarding first fire up): When the unit is turned on
for the first time, it should be turned onto high without the fan on for the first 4
hours. This will cure the paint, logs, gasket material and other products used in
the manufacturing process. It is advisable to open a window or door, as the unit
will start to smoke and can irritate some people. After the unit has gone through
the first burn, turn the unit off including the pilot, let the unit get cold then remove
the glass door and clean it with a good gas fireplace glass cleaner, available at
your local ENVIRO dealer.
4
Specifications
RATING LABEL LOCATION:
The rating label is located under the control panel and is attached to a rectangular metal sheet that is
chained to the fireplace.
DIMENSIONS:
Table 1: Sienna exterior dimensions. (Shaded dimensions shown in Figure 1 & 2.)
Surround Style
Distance
Direct Vent
B-Vent
Arched Surround
From Flue To Surround
14 / ” (376 mm)
14 9/16” (370 mm)
From Back/Sensor To Surround
17 5/16” (439 mm)
18 7⁄8” (479 mm)
33” x 46” (840 x 1930 mm)
Surround
From Flue To Surround
14 1⁄2” (369 mm)
14 3⁄8” (365 mm)
From Back/Sensor To Surround
17 / ” (434 mm)
18 11/16” (474 mm)
33” x 46” (840 x 1930 mm)
Surround with Trim
From Flue To Trim
13 1⁄4” (337 mm)
13 1/16” (333 mm)
From Back/Sensor To Trim
15 13/16” (402 mm)
17 3⁄8” (441 mm)
11 16
1 16
33 9/16"
(852 mm)
Shown: Direct Vent with
arched surround panel
33 1/8"
(841 mm)
21"
(533 mm)
Back
Flue
17 5/16"
(439 mm)
14 11/16"
(374 mm)
39 1/2"
(1004 mm)
27 3/4"
(705 mm)
26 1/8"
(663 mm)
30 1/2"
(775 mm)
15 1/16"
(383 mm)
23 7/16"
(596 mm)
22 11/16"
(576 mm)
20 5/8"
(523 mm)
Figure 1: Sienna exterior dimensions; example 1.
5
Specifications
21"
(533 mm)
Sensor
Flue
13 1/16"
(333 mm)
With Trim 46 1/8" (1171 mm)
Without Trim 46" (1168 mm)
17 3/8"
(441 mm)
1 3/8"
(36 mm)
With Trim
33 3/16"
(343 mm)
Without Trim
33" (338 mm)
30 1/2"
(775 mm)
15 1/16"
(383 mm)
Figure 2: Sienna exterior dimensions; example 2.
6
Shown: B-Vent with
33" x 46" (84cm x 193 cm)
surround panel with trim
22 11/16"
(576 mm)
22 3/4"
(577 mm)
20 5/8"
(523 mm)
Operating Instructions
For Your Safety, Read Safety Precautions And Lighting Instructions Before Operating
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION
MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OF LOSS OF LIFE.
PILOT LIGHTING INSTRUCTIONS:
CAUTION:
Hot while operating. Do not touch, severe burns may result. Keep children, clothing,
furniture, gasoline or other flammable vapors away.
CAUTION: Do not operate this fireplace with the glass removed, cracked or broken. Replacement of the panel(s) should be done by a licensed or
qualified person! This appliance needs fresh air for safe operation and must be installed with provisions for combustion and ventilation air. See
installation and operating instructions manual. Keep burner and control compartment clean.
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage, or loss of life. Refer to owner's
information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or the gas supplier.
See installation and operating instructions accompanying appliance. Installation and service must be performed by a qualified installer, service agency,
or the gas supplier.
FOR YOUR SAFETY READ BEFORE OPERATING
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING
PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
C) Use only your hand to push in or turn the gas control knob;
A) This appliance is equipped with a pilot, which must be lit by hand by
NEVER use tools. If the knob will not push in or turn by hand, do
following these instructions exactly.
not try to repair it. Call a qualified service technician. Force or
B) BEFORE LIGHTING smell all around the appliance area for gas and next to
attempted repair may result in a fire or explosion.
the floor because some gas is heavier than air and will settle on the floor.
D) Do not use this appliance if any part has been under water.
WHAT TO DO IF YOU SMELL GAS:
Immediately call a qualified service technician to inspect the
Do not try to light any appliance. Do not touch any electrical switch: do not
appliance and to replace any part of the control system and any
use any phone in your building. Immediately call your gas supplier from a
gas control which has been under water.
neighbor's phone. Follow the gas suppliers instructions. If you cannot reach
your gas supplier, call the fire department.
LIGHTING INSTRUCTIONS
WARNING: this gas valve has a lockout device, which will not allow the
pilot burner to be relit until the thermocouple has cooled. If the knob does
not pop up when released, stop and immediately call your service
technician or gas supplier.
If the pilot does not stay lit after several tries, turn the gas control knob
to “OFF” and call your service technician or gas supplier.
6. Turn the gas control knob counter clockwise
to the “ON”
position. Flip the burner switch to “ON” THEN TURN THE “HI/LOW”
knob to the desired setting.
7. Turn on the electrical power to the unit.
OUT
TP TH
I
L
O
H
TP
O FF
PI L OT
TH
ON
STOP! Read the safety information above on this label.
Turn off all electrical power to this appliance.
Turn off the gas control knob clockwise
to the off position.
Open door. Wait fIve (5) minutes to clear out any gas. Close door. If
you smell gas STOP! Follow “B” in the above safety information. If
you do not smell gas go to the next step.
5. Find pilot-located to the left under the front log. Turn the gas control
knob counter-clockwise
to “PILOT”. Push the gas control in fully
and hold, keep knob depressed for about 30 seconds after
the pilot is lit. Release knob. If pilot goes out, repeat
steps 4 through 5.
IN
1.
2.
3.
4.
LO
PI T
TO TURN OFF GAS TO APPLIANCE
1. Flip burner switch to “OFF”
2. Turn the gas control knob clockwise
to the “OFF” position.
������������
Figure 4. Pilot flame.
�������
Figure 3. Lighting instruction label.
BURNER LIGHTING:
����������
3. Turn off all electrical power to the appliance if service is to be performed.
1. Make sure the pilot is lit.
2. Turn gas control knob COUNTER
CLOCKWISE to ON.
3. Flip the burner switch to ON.
4. Turn HI/LO knob to the desired flame
height.
5. Turn on all electrical power to the unit.
NOTE: Check that all burner holes are lit.
Figure 5. Control panel.
REMOTE CONTROLS - OPTIONAL:
This fireplace can use an optional remote control or an optional cordless wall thermostat. If either of
these are to be used to control the fireplace for the majority of the time, leave the ON/OFF switch (on the
control panel) in the remote/thermostat position. Consult the instructions included with the remote/wall
thermostat for operation guidelines.
7
Operating Instructions
For Your Safety, Read Safety Precautions And
Lighting Instructions Before Operating
TURN OFF UNIT:
Flip switch to OFF to turn off burners only.
If the fireplace is to be turned off for the season, or for servicing, turn the gas shut off valve to OFF. If
the unit is going to be serviced, turn off the electrical power to the unit as well.
NOTE: When the unit is turned on for the first time, it should be turned onto high, with the fan OFF,
for the first two to four hours. This will cure the paint, logs, gasket material, and other products used
in the manufacturing process. It is advised that a door or window be opened, as the unit will start to
smoke, which can irritate some people. After the unit has gone through the first burn, turn the unit OFF,
including the pilot, and let the unit get completely cold. Then remove the glass and clean it with a good
gas fireplace glass cleaner, available at your local Enviro dealer. See “DOOR REMOVAL” and “CLEANING THE
GLASS” sections.
BLOWER SPEED:
The blower will come on only when the fireplace is up to temperature (approximately
20 minutes). Turning the fan control knob will change the speed of the fan. To turn
the blower off, turn the knob COUNTER-CLOCKWISE until it “clicks” off (Figure 6).
It is advisable not to operate the blower below 1/3 speed as it puts a strain on the
windings of the blower and running the blower at lower speeds could also cause
premature fan failure.
NORMAL SOUNDS DURING OPERATION:
��
���
��
Figure 6. Fan control.
Table 2: Normal Sounds.
Component
Sound & Reason
Focus & Fascia
Creaking when heating up or cooling down.
Burner
Light pop or poof when turned off; this is more common with LP units.
Temperature Sensor
Clinking when it senses to turn the blower on or off.
Pilot Flame
Quiet whisper while the pilot flame in on.
Blower / Fan
Air movement that increase and decreases with the speed of the blower. The
blower is pushing the heat from the fireplace into the room.
Gas Control Valve
Dull click when turning on or off, this is the valve opening and closing.
ADJUSTING VENTURI AIR SETTINGS:
There is one venturi adjustment.
Use this venturi adjustment lever, shown in Figure 7, to
achieve a proper and efficient flame.
Adjust lever until the flame pattern is similar to Figure
36. Suggested pull out distances are 1⁄2” (13 mm)
minimum for Natural Gas and 7⁄8” (22 mm) minimum
for Propane.
Pull out the venturi adjustment to increase primary air at the venturi tube.
Push in the venturi adjustment to decrease primary air at the venturi tube.
Figure 7: Adjusting the venturi air setting.
8
Maintenance And Service
Warning: Failure to position the parts in accordance with this manual, or failure to use only parts
specifically approved with this appliance, may result in property damage or personal injury.
At least once a year, run through the following procedures to ensure the system is clean and working
properly. Check the burner to see if all the ports are clear and clean. Check the pilot to make sure it is
not blocked by anything. The pilot flame should be blue with little or no yellow on the tips.
The venting system must be periodically examined; it is recommended the examination is done by a
qualified agency.
CLEANING THE GLASS:
When the fireplace is cool, remove the face of the fireplace along with the glass door. See MAINTENANCE
AND SERVICE - GLASS DOOR REMOVAL. Check the gasket material on the back of the glass, making sure that
it is attached and intact.
During a cold start up, condensation will sometimes form on the glass. This is a normal condition with all
fireplaces. However, this condensation can allow dust and lint to cling to the glass surface. Initial paint
curing of the appliance can leave a slight film behind the glass, a temporary problem. The glass will need
cleaning after the fireplace has cooled off from the first burn and about two weeks after first burn. Use
a mild glass cleaner and a soft cloth. Abrasive cleaners will damage the glass and plated
surfaces. Depending on the amount of use, the glass should require cleaning no more than two or three
times a season. Do not clean the glass when it is hot.
CLEANING THE FIREBOX:
Remove the logs carefully, as they are very fragile. Gently remove all the embers and rock wool and place
on a paper towel. Vacuum the bottom of the firebox thoroughly. Carefully clean any dust off the logs and
remove any lint from the burner and pilot. At this time, inspect the burner pan for cracking or severe
warping. If a problem is suspected, contact the dealer. Check the logs for deterioration or large amounts
of soot; a small amount on the bottom side of the logs is normal. Replace the logs and embers as in the
SECONDARY INSTALLATION - LOG SET AND EMBER INSTALLATION section. If new/more embers and rock wool are
required, contact your nearest ENVIRO dealer.
REPLACING THE GLASS:
The glass in the fireplace is a high temperature ceramic. If the glass is damaged in any way, a factory
replacement is required (see PARTS LIST). Wear gloves when handling damaged glass door assembly
to prevent personal injury. When the glass door assembly is being transported, it must be wrapped in
newsprint and tape and/or a strong plastic bag. Do not operate with the glass front removed, cracked
or broken. Removal and replacement of the glass from the door must be done by a licensed or qualified
service person. The glass must be purchased from an ENVIRO dealer. No substitute materials
are allowed.
CLEANING THE PLATED SURFACES:
Painted faces should be wiped with a damp cloth periodically. If a plated face has been purchased, it
should be unpacked/unwrapped carefully to avoid getting anything on the surface of the finish, including
cleaners, polish and finger prints. It is important to note that fingerprints and other marks can leave
a permanent stain on plated finishes. To avoid this, give the face a quick wipe with denatured
alcohol on a soft cloth BEFORE lighting the fireplace. Never clean the face when it is hot. Do
not use other cleaners as they may leave a residue, which can become permanently etched into the
surface.
9
Maintenance And Service
QUALIFIED INSTALLERS ONLY
GLASS DOOR REMOVAL:
Open the door by removing the two (2)
5/16’’ bolts located at the top outside
corners of the glass frame (see Figure
8). Lift the bottom of the door up and
remove from unit (see Figure 9).
CAUTION GLASS MAY
SEPARATE FROM DOOR.
Figure : Top bolts for glass door.
Figure 9: Bottom hooks for
glass door.
BURNER & BLOWER REMOVAL:
1. Turn the unit off and allow the unit to cool
completely.
2. Remove the fascia or louvers, open the door
(see MAINTENANCE AND SERVICE - GLASS DOOR
Burner Top with
REMOVAL), and remove the log set.
Grate Attached
3. Remove the log support tray by lifting the
back of the tray up and pull it out from under
the lip. Take care to not knock the pilot and
Gas & Electrical
Tray Complete
the side brick panels.
4. Remove the centre and top brick panels (see
SECONDARY INSTALATION - REMOVING THE BRICK
PANEL).
5. Turn gas supply off and remove gas
connection. Disconnect the wiring from the
Log Support
Blower / Fan
side of the appliance.
Tray
6. Remove the three (3) T-20 screws just
above the burner top on the back firewall
(see Figure 10) and the two (2) screws on
Figure 10: Removing burner and gas tray.
each side below the burner top. Carefully
remove the complete gas and electrical tray assembly from the firebox, ensuring that no wires or gas
lines are damaged.
7. Remove the blower and housing from the gas tray assembly by removing the three (3) fastening screws
located on the back of the gas tray assembly. Pull the fan out from under the gas tray. Disconnect the
wiring from the fan temperature sensor and remove fan.
8. Hook up wires from the new blower to main wiring harness and fan temperature sensor. Install the
blower in the reverse order as described in Step 7.
6. Reinstall the completed gas tray into the firebox, being careful not to damage any wires or gas lines.
Properly secure the gas tray assembly in the firebox. Hook up gas lines and wiring harness. Perform a
gas leak check on all gas line with a soap and water solution or an approved method.
7. Return unit to original location if moved. Re-install the log support tray, the brick panels, the logset
(see SECONDARY INSTALATION - LOG SET AND EMBER INSTALLATION), the door and the fascia or louvers.
8. Check burner and blower assembly for proper operation.
Caution: Bleed lines before lighting and light pilot with door open.
10
Maintenance And Service
FUEL CONVERSION:
TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLY
Please read and understand these instructions before installing.
Warning: This conversion kit shall be installed by a qualified service agency in accordance
with the manufacturer’s instructions and all applicable codes and requirements of the
authority having jurisdiction. If the information in these instructions is not followed
exactly, a fire, explosion or production of carbon monoxide may result causing property
damage, personal injury or loss of life. The qualified service agency is responsible for
the proper installation of this kit. The installation is not proper or complete until the
operation of the converted appliance is checked as specified in the manufacturer’s
instructions supplied with the kit.
Kit Parts List:
1
1
1
1
-
Orifice (NG #32 DMS or LP #49 DMS)
Pilot Injector (NG 0.62 mm; LP 0.35 mm)
Installation instruction sheet
Conversion label
Carefully inspect all parts supplied with this conversion kit. If any parts have been damaged or are
missing, contact your dealer, distributor or courier company to have them replaced before starting this
installation.
Conversion Kit Installation:
1. Turn control knob on the gas valve to the “OFF” position and shut the gas supply off at the shut-off
valve upstream of the unit. CAUTION: The gas supply must be shut off prior to disconnecting the
electrical power and before proceeding with the conversion. Allow the valve and unit to cool down
to room temperature.
2. Remove the glass as shown in the MAINTENANCE AND SERVICE - GLASS DOOR REMOVAL.
3. Carefully remove the log set and ember material if they are installed.
4. Remove the burner as shown in the MAINTENANCE AND SERVICE - BURNER AND BLOWER REMOVAL.
5. Convert the burner orifice(s):
a) Remove the main burner orifice with a 1⁄2 inch deep socket.
b) Put a bead of pipe-thread sealant or approved Teflon tape on the orifice
threads before installing into the brass elbow.
c) Install the new orifice(s) from the kit into the brass elbow.
6. Convert the pilot injector:
a) Pull the pilot hood straight up to access the pilot injector.
b) Using a 5/32” or 4 mm Allen key, remove the pilot injector.
c) Install the new pilot injector supplied with this conversion kit. Simply screw
the new injector inside the pilot hood using the Allen key,
d) Reinstall the hood by placing the hood on the assembly, line up the key
way, and snap into place.
7. Convert the SIT gas valve:
Figure 11: Removing
a) Remove the black protection cap from the HI/LO knob by hand shown in
valve cap.
Figure 11.
11
Maintenance And Service
b) Insert a 5/32” or 4 mm Allen wrench into the hexagonal key-way of the screw (see Figure 12), rotate
it counter-clockwise until it is free and extract it.
Loosen
Tighten
c) Check that the screw is clean and if necessary
remove dirt.
d) Flip the screw (refer to Figure 13).
e) Using the Allen wrench as shown in Figure 12,
rotate the screw clockwise until a torque of 9 inch
lbs. WARNING! Do not over tighten the screw.
It is recommended that you grip the wrench by
the short side.
f) Verify that if the conversion is from NG to LPG,
the screw must be re-assembled with the red oring visible (refer to Figure 14). If the conversion
is from LPG to NG, the red o-ring of the screw
must be not visible.
g) Re-attach the black protection cap that was
removed in step a (Figure 11).
Figure 13: Flip valve
screw.
Figure 12: Removing valve
screw.
8.
Red o-ring
Red o-ring
Reinstall the burner, brick panels,
is visible
is not visible
log set, embers, and glass door. Also
refer to SECONDARY INSTALLATION INSTALLING LOG SET AND EMBERS. When
re-installing the burner, ensure that
the burner to pilot hood relationship
is similar to what is shown in Figure
LPG Configuration
15. On some units you will need to
Figure 14: O-ring on valve screw.
pay special attention when installing
the burner that the venturi adjustment rod is properly installed into
the venturi adjustment piece welded to the burner venturi tube
9. Reconnect the main gas line if it was disconnected and open the
shut-off valve at the gas line to the unit.
10. Use a small brush to apply a warm soapy water solution to all gas
connections (use a half dish soap and half warm water). If a gas leak
is present, bubbling will occur. Gas leaks can be repaired by using an
approved pipe thread sealant or approved Teflon tape. NEVER USE
AN OPEN FLAME WHEN TESTING FOR LEAKS.
11. Reconnect the electrical power to the unit.
Figure 15: Burner to pilot hood
12. Relight the main burner in both the “HI” and “LO” positions to verify properrelationship.
burner ignition and
operation and proper flame appearance. Also refer to SECONDARY INSTALLATION - LOG SET AND EMBERS
INSTALLATION for a flame appearance picture.
13. MAKE SURE that the conversion label is installed on or close to the rating label to signify that the
unit has been converted to a different fuel type.
12
Initial Installation
WARNING: Operation of this heater when not connected to a properly installed and maintained
venting system can result in carbon monoxide (CO) poisoning and possible death.
CLEARANCES TO COMBUSTIBLES:
Maintain sufficient clearances for operation, service and maintenance.
• A clearance of 25 1⁄2” (648 mm) minimum is required from the center of the unit to the sidewalls.
• A 2” (51 mm) wide mantel can be mounted at a
minimum height of 39” (991 mm) from the bottom
of unit.
• A 10” (254 mm) wide mantel can be mounted at a
minimum height of 43” (1092 mm) from the bottom
of unit.
2" (51mm)
Mantle
39" (991 mm)
minimum to
bottom of unit
Sienna
EXAMPLE: If the Sienna is raised
6" (152mm) and has 4" (102mm)
wide hearth in front of it then 12"
(305mm) of non-combustible
floor protection is require to
be installed in front of the
hearth.
16" (406mm)
15" (381mm)
14" (356mm)
13" (330mm)
12" (305mm)
11" (279mm)
10" (254mm)
9" (229mm)
8" (203mm)
7" (178mm)
6" (152mm)
Hearth Height
of 6" (152mm)
5" (127mm)
0" (0mm)
43" (1092 mm)
minimum to
bottom of unit
Figure 16: Mantle width and height.
6" (152mm)
11" (279mm)
12" (305mm)
• If installed at floor level, a minimum 16” (406 mm)
non-combustible material must be installed in front
of the unit.
• If installed on a 12” (305 mm) wide hearth raised a
minimum height of 6” (152 mm), no floor protection
is required.
• Refer to Figure 9 for additional required floor
protection dimensions with different width hearths.
10" (254mm) Mantle
Non-combustible
floor protection required
in front of corresponding
hearth width
Figure 17: Floor protection distance required.
13
Initial Installation
WARNING: Operation of this heater when not connected to a properly installed and maintained
venting system can result in carbon monoxide (CO) poisoning and possible death.
MINIMUM FIREPLACE SIZE:
Table 3: Minimum dimensions of fireplace for Sienna to be installed into.
Description of Fireplace Dimension
At Back
Width
At Front
With Surround Only
Height
With Surround with Trim
With Surround Only
Depth
With Surround with Trim
Direct Vent
23 1⁄4” (591 mm)
35” (889 mm)
23 3⁄4” (603 mm)
23” (584 mm)
18” (457 mm)
16 1⁄2” (419 mm)
B-Vent
23 1⁄4” (591 mm)
35” (889 mm)
23 3⁄4” (603 mm)
23” (584 mm)
19” (483 mm)
17 1⁄2” (445 mm)
B-VENT MODEL:
WARNING: This appliance has been designed to operate by drawing combustion air and dilution air
from the room. It is also designed to draw room air for proper heat circulation from the sides of the
unit. Blocking or modifying the louvers in any way can create hazardous situations, either through poor
venting or by overheating. It is important that this unit has sufficient air circulation for proper venting
and combustion. Provisions must be made for the supply of adequate combustion and ventilation air.
These openings must not be blocked. The appliance must not be connected to a chimney flue servicing
a separate solid fuel-burning appliance.
AUTOMATIC FLUE GAS SPILL SWITCH - B-VENT MODEL ONLY:
NOTE: This heater must be properly connected to a venting system. This heater is equipped
with a vent safety shutoff system designed to protect against improper venting of combustion
products. This safety switch is located on the rear of the appliance. If the switch trips more
than once, the venting should be inspected by a qualified service technician for possible
blockage or severe down draft conditions.
The draft hood must be in the same pressure zone as
the air inlet. Inspect for draft from the front of the unit
at the 1⁄4” tube shown in Figure 18. Check for a draft
using smoke; a vacuum or suction into the tube will
indicate proper drafting. If air is blowing out of the tube
the problem must be corrected before the unit can be
started.
This model can be vented with 4” aluminum or stainless
steel flex vent and/or certified Type B Gas Vent. The
flue collar of the appliance will fit inside of a standard
4” vent and may be fastened directly to the vent. Check
periodically that the vent is unrestricted and an adequate
draft is present when the unit is in operation.
14
Check draft with a match
or smoke in a 1⁄4" (6 mm)
tube located here.
Figure 18: Draft check.
Initial Installation
QUALIFIED INSTALLERS ONLY
DIRECT VENT MODEL:
WARNING: This appliance has been designed to draw room air for proper heat circulation
from the sides of the unit. Blocking or modifying the louvers in any way can create hazardous
situations.
This model is vented with two (2) 3” aluminum or stainless steel flex vent leading into a co-linear to
co-axial vent adaptor and using a vertical termination cap. The flue collars of this model will fit inside of
standard 3” vent and may be fastened directly to the vent. The Exhaust vent is on the right of the flue
connector. The Air Intake is on the left side of the vent collar plate (this outlet is not in the center, it is off
to one side of the vent collar plate.)
Check periodically that the vents are unrestricted. Also ensure that all direct vent pipes have been
properly sealed and installed after routine inspection or cleaning. The air intake and exhaust pipes must
be installed in the correct locations on the removable connector.
PREPARING YOUR SIENNA FOR INSTALLATION:
• Remove the packaging from the appliance and surround panels; check to make sure there is no
damage. Carefully check the glass door. Do not use the unit if it is damaged. In the event damage is
found, please report it to both the courier and your dealer as soon as possible.
• Carefully clean the fireplace and flue before installing the stove. Failure to do so may result in fumes
or dirt being blown into the room and may cause a fire leading to death or serious injury.
1. Remove the unit from the box and remove all packaging material from the appliance.
2. Remove door. See MAINTENANCE AND SERVICE - GLASS DOOR REMOVAL.
3. Remove log and ember set and all wrapping material from the stove. Remove wrapping material from
log and embers and check for any damage. If damage is observed, do not use unit and contact your
local dealer.
4. Remove the vent collar plate from the top of the stove by unscrewing the two (2) T-20 Torx screws
located on the center top of the stove. Slide the collar plate backwards. If the fireplace that the unit
is to be installed into is high, the collar plate does not need to be removed. Properly secure the vent
collar plate to the flexible vent pipe liner(s) previously installed in the chimney. Be careful not to overstretch the liner(s).
5. Place the unit part way into the fireplace. Connect the fireplace insert’s flexible gas line to the
household gas supply, using locally approved methods. Place the electric cable so it can be connected
to the power supply.
6. As you push the unit into its final position
in the fireplace, if the vent collar plate was
removed, reinstall it to the stove by sliding
it along the draft hood and secure with the
screw.
7. Adjust the leveling legs to ensure the unit
is level. There are two (2) leveling legs on
each side (shown in Figure 19).
Leveling Legs
two (2) on each side
Figure 19: Leveling legs position.
15
Initial Installation
QUALIFIED INSTALLERS ONLY
VENTING FIREPLACE INSERTS:
The ENVIRO SIENNA may be installed and vented into any solid fuel fireplace that has been installed
in accordance with the National, Provincial/State and local building codes and has been constructed of
non-combustible materials. Before starting refer to INITIAL INSTALLATION - PREPARING YOUR SIENNA FOR
INSTALLATION and INITIAL INSTALLATION - CONVERTING A DIRECT VENT FIREPLACE TO A B-VENT FIREPLACE.
An approved chimney liner and rain cap must be used. A throat connector or flashing must be installed
to ensure a tight seal, top performance, safety and efficiency. Carefully follow the manufacturer’s
instructions that accompany the chimney liner kit.
Remove the vent collar plate from the top of the insert and connect it securely with sheet metal screws
and/or hose clamps. Check for any tears in the liner at this point. IMPORTANT: The screws that hold
the vent collar plate in its approved position must be installed.
DV Only: Maximum height allowed
for the vent is 35ft (10.67m).
Install sealed throat connector or
flashing to prevent leakage of room air
up through chimney.
DV Only: Before installing vent
liners, mark each liner on both ends
to designate which is the intake and
the exhaust.
Measure the height of the chimney
beforehand and purchase the
appropriate kit. Never attempt to overstretch a flexible liner to accommodate
the height of the chimney.
Any flue damper must be removed or
blocked permanently in the open
position.
The chimney must be clean, in good
working order and constructed of noncombustible materials.
�� �����
Make sure that all chimney cleanouts
are tight fitting and will not permit air to
leak into the chimney
Figure 20: Installation of Sienna DV and BV.
16
�� �����
Initial Installation
QUALIFIED INSTALLERS ONLY
ELECTRICAL REQUIREMENTS:
The fan is thermostatically controlled and it will
not operate if the appliance is cold. A few minutes
after the appliance is lit and the variable speed
control is set at a desired setting, the fan will
automatically turn on. The fan will automatically
turn off after the appliance has cooled down.
120oF (49oC)
Temperature Sensor
Fan Control
CNT4
Black
CNT1
White
Black
The fireplace must be electrically connected and
grounded in accordance with local codes or, in the
absence of local codes, with the current CSA C22.1
Canadian Electrical Code Part 1, Safety Standards
For Electrical Installations, or The National
Electrical Code ANSI / NFPA 70 in the US.
Black
CNT3
Green
CNT2
Power Cord
120V AC
Green/Yellow
White
WARNING: The electrical grounding instructions
must be followed. The fan kit is equipped with a
three-prong (grounding) plug for your protection
against shock hazard, and should be plugged
directly into a properly grounded three-prong
outlet. DO NOT cut or remove the grounding
prong from this plug.
FAN
Figure 21: Fan wiring diagram.
Thermocouple
Grey
O
O
N
FF
70 ° F
ON/OFF/REMOTE
Thermostat Switch
Optional
Remote
Control
Purple
Manifold
Pressure
Tap
Blue
70 ° F
UP
DOWN
COOL / HEAT
PROGRAM
Optional
Thermostat
Thermopile
Optional
Wall Switch
BV Only
300oF (149oC)
Temperature
Sensor
(DV has only
connectors)
Inlet
Pressure
Tap
Gas
Control
Valve
Blue
Pilot
Adjustment
Screw
CAUTION: When servicing controls,
label all wires prior to disconnection.
Wiring errors can cause improper
and dangerous operation. Verify
proper operation after servicing.
Table 4. Recommended Thermostat
Wire Size.
Wire Size
Max. Length
14 gauge
100 ft (30.48 m)
16 gauge
60 ft (18.29 m)
18 gauge
40 ft (12.00 m)
20 gauge
25 ft (7.62 m)
22 gauge
18 ft (5.49 m)
Figure 22: Wiring of a valve and thermostat.
17
Initial Installation
QUALIFIED INSTALLERS ONLY
GAS LINE CONNECTION:
Warning: Only persons licensed to work with gas piping may make the necessary gas connections to
this appliance.
Gas Line Connection:
•This fireplace is equipped with a certified flexible pipe located on the right side of the unit, terminating
in a 3⁄8” male NPT fitting. Consult the local authorities for local codes or use the CAN/CGA B149 (1 or 2)
installation code in Canada. In the US, gas installations follow either local codes or the current edition of
the National Fuel Gas Code ANSI Z223.1.
•The efficiency of this unit is a product thermal efficiency rating determined under continuous operating
conditions and was determined independently of any installed system.
�����
�������� ���
��������
�������� ���
IN
OUT
TP TH
I
L
O
TP
H
O FF
PI L OT
TH
ON
LO
PI T
����� ����������
�����
������
����
��� �������
����
Figure 23: Fully labeled gas valve.
TO TEST VALVE PRESSURES:
The pressure taps are located on the top right
of the valve.
• Turn set screw one (1) turn counter-clockwise
to loosen.
• Place 5/16 in (8 mm) I.D. hose over the
pressure taps.
• Check pressures using a manometer.
• When finished, release pressure, remove
hose and tighten set screw.
The appliance and its’ shut-off valves must be
disconnected from the gas supply piping system
during any pressure testing where the pressure
exceeds 1⁄2 psig (3.45 KPa) or the valve will be
damaged.
The unit must be isolated from the gas supply
piping system by closing its’ individual manual
shut off valve during any pressure testing of the
gas supply piping system at pressures equal to
or less than 1⁄2 psig (3.45 KPa).
Always check for gas leaks with a soap and
water solution after completing the required
pressure test.
Table 5: Orifice and Pressure Information.
Main Burner
Natural Gas
Propane Gas
Orifice:
#32 DMS
#49 DMS
Venturi Setting:
1⁄2” Min.
7⁄8” Min.
Manifold Press:
3.8 W.C. (0.95 KPa) 11.0 W.C. (2.74 KPa)
Min. Manifold Press: 1.2 W.C. (0.30 KPa) 2.7 W.C. (0.67 KPa)
Max. Supply Press:
7.0 W.C. (1.74 KPa)
13.0 W.C. (3.28 KPa)
Min. Supply Press:
5.0 W.C. (1.24 KPa) 12.0 W.C. (2.98 KPa)
Max. Input:
41,000 BTU/hr
(12.0 KW)
41,000 BTU/hr
(12.0 KW)
Min. Input:
23,000 BTU/hr
(6.7 KW)
21,000 BTU/hr
(6.1 KW)
NEVER USE AN OPEN FLAME FOR LEAK TESTING.
18
Initial Installation
QUALIFIED INSTALLERS ONLY
CONVERTING A DIRECT VENT FIREPLACE TO A B-VENT FIREPLACE:
1. Remove the Direct Vent
chimney connector assembly
by taking out the two (2) T-20
screws at the front of the unit.
Push the assembly out from
under the brackets at the back
and remove (see Figure 24).
2. Remove the two (2) fresh air
inlet covers from each side.
Cover locations shown in
Figure 24.
3. Slide the B-Vent chimney
connector assembly into the
same position the Direct Vent
chimney connector assembly
was in. Ensure the tabs are
under the brackets at the back
and the holes at the front line
up. Secure into place with the
two (2) T-20 screws at the
front of the unit.
4. Disconnect the two (2) blue
wires at the opening to the
right of the unit and connect
them to the 300°F (149°C)
manual reset spill switch at
the rear of the B-Vent chimney
connector with the wires
supplied. Refer to Figure 25.
Direct Vent
Connector Assembly
Fresh Air
Inlet Covers
Figure 24: Converting to a BV fireplace.
B-Vent
Connector Assembly
5. Test fire the appliance and
ensure proper operation. A
venturi adjustment could be
required to achieve an efficient
flame. Improper operation
or adjustment could result in
Carbon Monoxide production
causing personal injury or
property damage.
300°F (149°C)
manual reset
spill switch
Figure 25: Converting to a BV fireplace.
19
Secondary Installation
INSTALLATION OF SURROUND PANEL:
The Sienna must have one of the panels installed around the unit; the unit panel, the filler panel, or the
filler panel with trim. If you have trim for your filler panel, the trim must be installed before installing the
filler panel onto the unit.
1. Attach one side trim to the top trim using a corner bracket (see Figure
26) to secure pieces together. There are two (2) main pieces to each
corner bracket (see Figure 27). When installing the corner pieces into
the trim the “B FACE” sides must face each other and the screw heads
are to face out. With the bracket in place and the top and a side trim
snug together use a flat head screwdriver to turn the two (2) screws in
the bracket in to tighten it into the trim.
Surround
2. Slide the two (2) attached trim pieces onto the surround panel.
Panel
3. Attach the other side trim piece to the top trim using the same method
Figure 26: Corner brackets
used in Step 1.
for trim.
4. Place the second side of the trim
on the surround panel in the same
#8 screw
manner use on the first side and
Side
secure in the same manner.
Trim
5. On the side trims there are holes 2” (50
mm) from either end. Using a Phillips
screwdriver to place a #8 screw 11⁄4”
long in each hole and tighten (refer
to Figure 28). This will keep the trim
tight against the surround.
NOTE: The notch at the bottom of the
Surround Panel
left trim is so the power cord can be
run to the outside of the panel.
Figure 27: Two pieces of corner bracket.
Figure 28: Screw to
hold the trim against
the surround.
INSTALLATION: Lift the surround upright in
front of the fireplace with the four (4) hooks
pointing towards the fireplace. Slide the hooks
into their corresponding slots (see Figure 29).
Ensure the hooks are pushed all the way into
the slots and the notch on the hook must be on
the bottom of the slot. The surround should be
wiped with a damp cloth periodically.
REMOVAL: Lift the surround straight up in
order to unhook the notch on the hooks from
the bottom of the slots. Pull the surround out
away from the fireplace. Place the surround
where it will not be damaged.
Figure 29: Filler panel with trim installation.
20
Secondary Installation
LOG SET AND EMBER INSTALLATION:
NOTE: The logs are fragile and should be handled gently.
The placement of the logs is not arbitrary. If they are positioned incorrectly, the flames can be “pinched”
and will not burn correctly. The burner, and a few of the logs come with locator pins, notches and ledges,
which make alignment easier. Using the pictures provided, carefully set the logs in place (see Figures 30
through 35).
Figure 30: The first log to
be placed is the back log.
It leans on the back of the
firebox, push it back as far
back as you can.
Figure 30. Empty firebox with grate and locator pins.
Figure 31: The left log and
the right log both have two
(2) holes in them that will rest
over their corresponding two
(2) locator pins pointed out in
Figure 30.
Figure 31. First Stage Log Set Installation.
Figure 32: The bottom of the
left/center log will rest over
the locator pin on the burner
and against the grate. The top
half of the log must rest against
the back log, see Figure 31. The
center spot shown in Figure 31
is a knot in the back log for the
left/center log to rest against.
Ensure the log does not block
any burn ports.
Figure 32. Second Stage Log Set Installation.
21
Secondary Installation
Figure 33: The front end of the right/center log has a notch in it that is to rest around the right/center
post of the grate. The back end of the log rests on the burner tray (see Figure 32). Ensure the log does
not block any burn ports.
Figure 33. Third Stage Log Set Installation.
Figure 34: Once the logs are in
position the provided rock wool can
be placed irregularly in front of the
burner.
Figure 35: Place the embers
irregularly onto and around the front
of the burner to create a realistic
look. The ceramic fiber comes in
chunks that can be ripped into
smaller pieces.
Figure 34. Fourth Stage Log Set Installation.
WARNINGS: DO NOT pack this
ember material as this could create
an unsafe condition. The pieces
should be lightly placed so they don’t
block any of the burner ports.
DO NOT allow any of the embers to
rest against the pilot assembly.
Figure 35. Fifth Stage Log Set Installation.
22
Caution: Use only the type of
ember material supplied with this
fireplace. Due to the irregular size
of the ember material, there may
be more than required. Use of other
foreign materials on the burners may
create dangerous conditions.
Secondary Installation
Figure 36. Sienna complete log set-up with embers burning.
NOTE: While the glass is still removed, it is recommended that the gas line be purged by lighting the
pilot.
When lighting the fireplace for the first time since the log set and embers have been installed/replaced,
watch for ignition at ALL the burner ports. If a long delay is noticed, turn the appliance off and wait for
it to cool down. Remove the glass and rearrange the ember material, making sure none of the burner
ports air holes are blocked.
Never operate the fireplace with the glass door removed.
23
Secondary Installation
REMOVING THE BRICK PANEL:
The brick panel set is fragile, handle with extreme care.
The brick panel set comes pre-installed. The centre and top panel are the only panels that need to be
removed if the complete gas and electrical tray assembly must be removed. The side panels may remain
installed unless they are to be replaced.
1. Turn the unit off and allow the
unit to cool completely.
2. Remove the fascia or louvers,
open the door, and remove the
log set.
3. Pull out the bottom of the
centre panel while pushing up
on the top panel.
2
1
4. With the center panel out, the
top panel will easily come out.
Just slide the top edge back out
of the top lip in the firebox.
If the side and front panels must
be removed, continue with steps
5, 6, 7, and 8.
Figure 37: Brick Panel Installation.
5. Lift the front panel, located on
the firebox bottom, from one
end and remove the panel at
an angle through the fire box
opening.
6. Remove the log support tray by
lifting the back of the tray up
and pull it out from under the
lip. Take care not to knock the
pilot and the side brick panels.
7. Remove the two (2) T-20
screws holding the bottom of
the baffle (shown in Figure
38).
Figure 38: Brick Panel Installation.
8. Pull the panels out of the lips
at the front of the firebox and
carefully remove the panel from
the unit (shown in Figure 39).
To re-install, follow the above
steps in reverse. Ensure that
the front and side panels are
pushed as far forward as they
can be before continuing with the
installation.
24
Figure 39: Brick Panel Installation.
Trouble Shooting
Problem
Possible Cause
The main burner The gas valve may not be on.
does not ignite Thermostat is not calling for
when called for.
heat.
Solution
• Check that the gas control knob is in the “ON” position.
• Adjust the thermostat several degrees above ambient temperature.
Problem with gas valve.
• Use a DC voltmeter to measure the voltage across the TPTH and
TP terminals. Main operator voltage: Open circuit ≥ 325mV Closed
circuit ≥ 100mV
• If voltage is not present, check the control circuit for proper
operation.
• If proper control system voltage is present, replace the gas control.
Spark will not
light the pilot
after repeatedly
pressing the
spark ignitor.
Defective piezo ignitor.
• Check connections to ignitor.
• If ignitor connections are good but no spark, replace ignitor.
Broken spark electrode.
• Check for broken ceramic insulation, replace electrode if broken.
Misaligned spark electrode.
• If spark is not arcing from electrode to pilot, loosen the screws on the
pilot base adjust and tighten.
Pilot will not
remain lit.
Problem with thermocouple
circuit.
• Check for proper connection of the thermocouple to the rear of the
valve. If loose, fully tighten.
• Check pilot for full flame impingement around thermocouple. If flame
is too small, check gas pressure, adjust pilot rate screw, check pilot
head for damage.
• Check thermocouple voltage at valve. It must be greater than 5 mV.
If low, replace thermocouple.
Air in gas line (pilot dies while
knob is depressed).
• Bleed line.
• Check gas line pressure.
• Contact dealer.
Burners will not
remain lit.
Problem with thermopile
circuit.
• Check gas line pressure .
• Check for flame impingement on thermopile. If low, see “Pilot will not
remain lit”.
• Check thermopile for minimum of 300 mV when burner is switched
on.
• Check wiring to thermostat for breaks.
BV ONLY: Check for spillage at draft hood that may trip spill switch
Flame lifting
Leak in vent pipe
• Check for leaks in vent connections.
Improper vent configuration
• Check vent configuration with manual.
Terminal may be recirculating
flue gases
• Check to see if terminal is on correctly.
• May need to install high wind termination cap.
• Contact dealer.
Glass fogs up
Normal Condition: after the appliance warms up the glass will clear.
**Due to additives in gas, glass may get hazy during operation** Clean as needed.
Blue Flames
Normal during start up: flames will yellow as the fireplace heats up.
Flames are
Flame impingement
burning “dirty” or
sooting
• Check log positioning.
• Increase primary air by opening the venturi shutter and/or by
opening the vent restrictor.
See also “Burners will not remain lit.”
Remote control
doesn’t work
Problem with the remote
• One or more of the batteries are dead. See remote control
instructions.
Problem with fireplace
• The on/off switch is turned to OFF.
• The gas control valve is turned to PILOT or OFF.
• The pilot has gone out.
BV ONLY:
Insufficient air
for combustion
• Air tight house.
• Supply make up air to the unit.
• A vacuum in room due to
other air-moving device.
25
Parts List- Unit Components
Reference
Number
1
2
3
4
4
4
4
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
26
Part Description
120°F Ceramic Fan Temperature Sensor
300°F (149°C) Manual Reset Spill Switch (Normally Closed)
S.I.T. Nova Valve Convertible
Thermocouple
Spark Electrode with Ignitor Cable
Thermopile
Pilot Orifice NG Threaded
Pilot Orifice LP Threaded
Pilot Gasket
S.I.T. Piezo Ignitor
Burner Switch
Fan Controller - 115V
Domestic Power Cord - 115V
Convection Blower - 115V
SIT Pilot 1⁄8” Tube with End Furrels (1 piece)
Blank Orifice #73
Embers
On/Off Remote Control Kit
Programmable Wall Mounted Remote Control
Dual Bulb Door Gasket (10 feet)
Grate
Three Flame Pilot Hood
Burner
DV Flue Connector
Relief Door Gasket
Brick Panels (set of 4)
Log Support
Sienna Owner’s Manual
Door, Glass, & Gasket
Log Set with Embers
Burner Tray Complete
Air Intake Covers
BV Vent Connector
Conversion Kit from LP to NG Convertible
Conversion Kit from NG to LP Convertible
S.I.T. Valve Conversion Screw W/oring
S.I.T. Valve Conversion Screw Cap
Part
Number
EC-001
EC-003
50-1421
EC-009
EC-011
EC-012
EC-019
EC-020
EC-021
EC-023
EC-026
EC-039
EC-042
EC-069
30-043
50-343
50-491
50-559
50-583
50-634
50-916
50-925
50-1089
50-1090
50-1091
50-1092
50-1093
50-1096
50-1112
50-1114
50-1115
50-1116
50-1117
50-1440
50-1441
50-1450
50-1451
October 2004
��
SIENNA - Components
�
��
��
��
��
��
��
��
��
��
Parts Diagram - Components
27
Parts Diagram - Burner
��
��
��
�
�
��
�
��
�
�
�
�
SIENNA - Burner
October 2004
28
�
Parts List - Options
Reference
Number
1A
1A
1A
1A
2A
3A
4A
5A
6A
7A
Option Description
The Cottage Trim Kit - Gold
The Cottage Trim Kit - Pewter
The Cottage Trim Kit - Antique Copper
The Cottage Trim Kit - Painted Charcoal
Cape Cod Doors
Unit Panel & Keystone
Cottage
Filler Panel
Louvers (set of 2)
Panel Trim Set 46” x 30” (117cm x 76cm) - Black
Part
Number
50-548
50-549
50-550
50-694
50-1097
50-1108
50-1109
50-1110
50-1111
50-1113
29
Parts Diagram - Options
��
��
��
��
��
��
��
SIENNA - Options
October 2004
30
Warranty
Sherwood Industries Ltd. offers a Limited Lifetime Warranty on this gas product. This Limited Lifetime
Warranty covers the appliance for a period of seven years from the date of installation. This warranty
applies only to the original owner in the original location.
Covered under the lifetime warranty are: the surround, the chassis and the heat exchanger. These steel
components are covered against manufacturer’s defects for seven (7) years and the labour for the first
year. The following exclusions apply: over-firing due to incorrect setup or tampering, or damage caused
by incorrect installation, usage or abuse. The unit must be properly installed by a qualified technician or
installer, and must meet all local and national gas and building code requirements.
We also cover against manufacturer’s defects, under our Limited Lifetime warranty, the following
components: Log Set, Burners and Glass.
The following exclusions apply:
Plating - Damage caused by scratching, marring, chemicals, fingerprints, abrasive cleaners or discoloration
with age. Items with Antique Copper that have had a green discoloration of the finish. If discoloration
occurs, please follow the cleaning instructions as outlined in the “Maintaining Face and Surround Finishes”
section.
Glass - use of harsh or abrasive cleaners, striking the glass or surface contaminates.
Logset - Damage caused by incorrect handling or misuse.
Burners - damage caused by improper or continuous operation under incorrect conditions.
Sherwood Industries Ltd. offers a two-year warranty on all the electrical components and gas components,
against manufacturing defects. Paint is also covered against flaking. This offer includes parts and labour
for one year, and parts only thereafter.
Your dealer shall make all claims under this warranty in writing. When filing a warranty claim, please
complete the following information on an official warranty claim form:
TO THE DEALER:
Name, address and telephone number of purchaser and date of purchase, date of installation, name of
installer and dealer, nature of complaint, defects or malfunction, description and part number of any parts
replaced.
TO THE DISTRIBUTOR:
Sign and verify that work and information are correct.
This warranty covers defects in materials and workmanship only if the product has been installed according
to the manual’s instructions. If the product is damaged or broken as a result of misuse or mishandling,
the warranty does not apply. The warranty does not cover removal and reinstallation costs.
Sherwood Industries Ltd. reserves the right to repair or replace the defective product. The shipping costs
are to be paid by the consumer. All warranties by the manufacturer are set forth and no claim shall be
made against the manufacturer on any oral warranty or representation.
Sherwood Industries Ltd. and its’ employees or representatives will not assume any damages, either
directly or indirectly, caused by improper usage, operation installation, servicing or maintenance of this
appliance.
Sherwood Industries Ltd. reserves the right to make changes without notice. Please complete and mail
the warranty registration card and have the installer fill in the installation data sheet in the back of the
manual for warranty and future reference.
31
Installation Data Sheet
The following information must be recorded by the installer for warranty purposes and future reference.
NAME OF OWNER:
NAME OF DEALER:
_________________________________________
_________________________________________
ADDRESS:
ADDRESS:
_________________________________________
_________________________________________
_________________________________________
_________________________________________
_________________________________________
_________________________________________
PHONE:___________________________________
PHONE:___________________________________
MODEL:___________________________________
NAME OF INSTALLER:
SERIAL NUMBER:___________________________
DATE OF PURCHASE: _____________
_________________________________________
(dd/mm/yyyy)
DATE OF INSTALLATION:___________(dd/mm/yyyy)
� DIRECT VENT
� B-VENT
� NATURAL GAS (NAT)
� PROPANE(LPG)
ADDRESS:
_________________________________________
_________________________________________
INLET GAS PRESSURE:_________in wc
_________________________________________
PHONE:___________________________________
MAIN BURNER ORIFICE:__________# DMS
PILOT ORIFICE #_________OR________in diam.
INSTALLER’S SIGNATURE:
_________________________________________
MANUFACTURED BY:
SHERWOOD INDUSTRIES LTD.
6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3
www.envirofire.biz
March 20, 2006
C-11075
32
Download PDF

advertising