Remote Control Car Starter Installation Manual for

P R O F E S S I O N A L SERIES
Remote Control Car Starter Installation Manual for Models 25524, 25528
DesignTech International, Inc. • 7955 Cameron Brown Court • Springfield, Virginia 22153 USA • www.designtech-intl.com • 703-866-2000 or 800-337-4468
PLEASE READ COMPLETELY BEFORE BEGINNING
Congratulations on your purchase of the AutoCommand® Professional Series Remote Car Starter. The AutoCommand® Professional Series Remote Car Starter system allows you
to start the car by remote control from the comfort of your home or office in order to cool it down in the summer or heat it up in the winter.
AutoCommand® Professional Series is for automatic transmission/fuel injected vehicles only. It is an extremely sophisticated system with multiple built-in safety and
security features.
AutoCommand ® Professional Series Car Starter:
• Will start your car by remote control, and run the heater, defroster, or
air conditioner to warm up or cool down the car from up to 1,000 feet
away.
• Will shut off if the brake pedal is pushed, the hood is opened, or the
transmission is shifted out of park - unless the key is in the ignition and
in the “run” position.
• Is designed to start the car only if it is in park, and only if the hood is
closed.
• Allows you to remove the key while leaving the car running with the
doors locked for up to 10 or 15 minutes by utilizing the Quick Stop™
Option. (See Separate User Tip Sheet.)
• Has Lock, Unlock and Trunk keyless entry features.
• Will attempt to start the car for up to six seconds, but no longer (to
avoid damage to the starter motor). Should the car not start, or if it
stalls after starting, the remote starter will make two further attempts
to start it.
• Has alarm functions including starter kill which becomes active when
the doors are locked with the remote control.
• Will not let the car be driven without the key in the ignition.
• Shuts itself off automatically after 10 or 15 minutes (programmable) if
you forget to come out to your car.
• Starts the car automatically whenever the temperature drops below
0°F (-18°C), or if the battery voltage drops below 11 volts when the
Cold Start™ Option is used. (See Separate User Tip Sheet.)
• Has the “Daily Start™” feature which allows the vehicle to be started
at the same time the following day. (See Separate User Tip Sheet)
• Is quality engineered, microprocessor controlled, and made in the USA
to provide many years of reliable use.
• Comes with a Limited Lifetime Warranty.
Wiring Diagram
Tools required to install the AutoCommand® Professional Unit:
Wire Cutters/Strippers
Soldering Iron
Pliers
Electrical Tape
Power Harness
Color
Pink
White
Yellow
Blue
Green
Black
Screwdriver
Drill with1/4”and 5/16”
drill bits
Function
Power (+12V)
Accessory
Starter
Ignition 1
Ignition 2
Ground
Circuit
Type
Input
Relay output
Relay output
Relay output
Relay output
Input
Required
Yes
Yes
Yes
Yes
Consult Wiring Guide*
Yes
Test meter
We highly recommend that all connections be soldered for reliability.
Parts List included with the AutoCommand® Professional Unit:
Remote Starter
Receiver Module
Antenna
Control Harness
(10 position)
2 Relays with relay harnesses
(Model 25528 only)
Transmitter
Siren (Model 25528 only)
6 Power and Ignition wires
Shock Sensor
(Model 25528 only)
GREEN In Gear Loop
3 Pin
Lock/Unlock/Trunk
ON/OFF Switch Jack
Coax
Antenna
Jack
Control Harness
Color
White/Black
Brown/White
Brown
Blue
Yellow
Function
Ignition #3
Alarm Disarm
Accessory
Horn
Lights
Circuit Type
(–) 400 mA
(–) 400 mA
(–) 400 mA
(–) 400 mA
(+) Relay Output
Required
Consult Wiring Guide*
Consult Wiring Guide*
No
No
No
Following parts included in plastic baggy
Alchohol
Pad
Alcohol Pad
Green 30 A Fuse
On/Off Control Switch
Ring Terminal
Hood Pin Switch Set
2 Cable Ties
Plug-In LED
3 Pin Door Harness
Yellow Butt Connector
2 Protected by
DesignTech Labels
Warning Label
White - Option
Red LED Light
Red - Code Learn
Alarm Shock Sensor
Color
Function
Orange
Brake
Purple
Hood Switch
Green
Tach
Red/White
Alarm Input
Red/Black
Diesel
Circuit Type
(+) Input
(-) Input
(-) Input
(-) Input
(+/-) Input
Required
Yes
Yes
No
No
No
*For free vehicle-specific wire information consult our website at
www.designtech-intl.com
v3.1 S25524/28
Note: Failure to properly install the fuse holder and 30 amp fuse to the PINK wire to
the battery voids all product warranties.
On cars with airbags, you may notice bright yellow tubes or harnesses
marked SRS (Supplemental Restraint System) underneath the steering
column area. DO NOT tamper with these wires in any way, to prevent
personal injury and/or damage to the air bag system.
Ignition Key Diagram for Steps 4-7
The vehicle’s wires are found coming off of the key switch.
Remove the panel under the steering column to access
these wires.
Battery gases are explosive.
Do not smoke while working near the car’s battery.
Note: Some installers connect a battery charger to the vehicle’s battery during
installation. This is fine, but it must be removed before running the vehicle under
remote starter control.
4. Blue Wire (14 AWG) – Ignition 1
Connect the BLUE wire to the ignition 1 wire of your vehicle. This wire will measure
+12 Volts on the test meter in the “run” and “start” position, and is off in the “lock/
off” and “accessory” positions.
All General Motors (GM), rear wheel drive vehicles built prior to 1995
with automatic transmissions and Dodge Dakota trucks (4 cylinder
engines only) with automatic transmissions built prior to 1996 have a
MECHANICAL TYPE of NEUTRAL SAFETY SWITCH. See important
warning on the last page of these instructions.
5. Green (14 AWG) – Ignition 2
Connect the GREEN wire to the Ignition 2 wire in the vehicle. The Ignition 2 wire can
function in several different ways in your vehicle. It is important to understand how it
works. The Ignition 2 wire will usually measure +12 Volts in the “run” position and is
off (ground) in the “lock/off” and “accessory” positions. In certain vehicles, it may
also show +12 Volts in the “Start” position or Ignition 2 may turn OFF during “Crank”
and turn back ON after the starter disengages. Carefully note the function of the Ignition
2 wire. If the Ignition 2 turns OFF during “Crank”, set Option #4 (in section 24). If
Ignition 2 stays ON during “Crank,” no options need to be changed.
When running the wires through the car’s firewall, be sure to protect
them from sharp metal edges and from hot surfaces on and around the
engine.
INSTALLATION INSTRUCTIONS
6. White Wire (14 AWG) – Accessory
1. Before You Start
Connect the WHITE wire to the accessory wire which is +12 Volts in the “run” and
“accessory” position, but off in the “start” and “off” positions. In GM vehicles, connect
the white wire to the orange wire that is hot in “run” only.
Take time to read through the whole installation manual before beginning.
Always leave a window open to avoid locking your keys in your car.
IMPORTANT: After having read the entire manual, start the installation
by putting the yellow WARNING STICKER in the engine compartment.
Choose a surface that is clean and readily visible when the hood is open.
7. Yellow (14 AWG) – Starter
Connect the YELLOW wire to the starter wire. This wire will measure +12 Volts on
the test meter in the “start” position only.
Note: Most Nissan vehicles have two starter wires. Connect both starter wires of the
vehicle to the YELLOW start wire of the remote starter.
WARNING
This car is equipped with a remote control starting device.
Disable before working on car!
8A. Plug-In On/0ff Switch
AVERTISSEMENT
Ce véhicule est équipé d’un systéme de démarrage a distance. Mettez-le
hors fonction avant d’eflectuer toute opération d’entretien ou de réparation!
Mount the control switch so that it is easily accessible and so that
the “ON” position is facing upward. Make sure there is enough clearance behind the
mounted switch for the wire connections. Do not let the switch wires touch ground.
Do not plug the switch into the unit until it is mounted first. Connection of this switch
is mandatory. Use a 1/4" drill-bit for the mounting hole.
POWER & IGNITION HARNESS
The remote starter module will be installed under the dash once all wiring has been
completed. Do not mount the module at this time! You will need to check
the red diagnostic LED light as the installation progresses. Locate (or
drill) a hole in the firewall to run the PURPLE and GREEN wires of the Control
Harness and the PINK wire of the Power Harness into the engine compartment.
The remaining short wires stay in the passenger area. Leave about a foot of the wire
harness under the dash for ease of working and visual access to the diagnostic light.
Plug the ON/OFF control switch into the module just to the right of the power wires.
Turn the switch on.
8B. Plug-In LED Light
Drill a 5/16" hole in to the dash or panel to mount the LED light and plug the LED
light plug into the red connector. Mounting the LED light is not mandatory but the
LED light is used for alarm status, troubleshooting and programming options.
The Installation Information section of our web site www.designtech-intl.com is
available 24 hours/day to provide you with free, up-to-date vehicle wiring information
for your particular vehicle after you log in.
CONTROL HARNESS
ALL WIRES ARE THE SMALLER 18 AWG SIZE
Note: Always connect the PINK and BLACK wires before connecting any of the
other wires. Do not insert the fuse until step 11.
9. Purple Wire – Hood Pin Switch – Control Harness
The hood pin switch MUST be installed with the remote starter. It prevents operation
of the remote starter when the hood is open and is used to initialize the unit. Connect
the PURPLE wire to the hood pin switch using the red
connector.
2. Black Wire (16 AWG) – Ground
Connect the BLACK wire to a very good, clean chassis ground in the driver’s kick
panel area. Use the small ring terminal. (The thin metal bracing around or beneath
the dash board is not always adequate.)
Note: If you already have a hood pin switch which is
being used by a car alarm system, you may share the
wiring – but be sure to diode isolate each wire going to
the hood pin switch with the bands of diodes pointing
towards the pin switch as shown at right.
3. Pink Wire (12 AWG) – Power (+12 Volts)
Connect the ring terminal at the end of the short PINK wire to the +12 Volt terminal of
the battery. Run the long PINK wire through the firewall of your vehicle. Join the
remaining ends of the power wire together by soldering them. Tape with electrical
tape to leave no exposed wires. Alternatively, you may wish to use the yellow butt
connector, but we recommend soldering. Wait to insert the 30 amp green fuse into
the holder until step 11. As the power is first applied to the unit the red diagnostic
LED light will blink once.
v3.1 2428
To Alarm
To Remote Starter
How to share a hood pin
switch with an alarm
2
10. Orange Wire – Brake Shut-off – Control Harness
E. Turn the On/Off control switch back to the “ON” position
F. Start the car with the key and let it get to a normal idle. Do not press on the gas
pedal.
G. Push the red “code learn” button for a second.
H. Watch the red LED light. It will come on after 3 or 4 seconds, indicating that the
tach idle rate has been learned.
I. Turn the key to the “Lock/Off” position. You are now finished.
Connect the ORANGE wire to the brake wire which receives +12 Volts when the brake
pedal is depressed. This wire must be connected. It arms a critical safety feature
which disables the remote starter when the brake pedal is depressed.
Note: In some cars, the ignition must be in the “on” position to test the power in the
brake wire.
Note: If the Ignition 1 and Ignition 2 wires come on whenever the brake is depressed
and the hood is open this just means you need to initialize the unit in section 11.
Note: Once these steps are complete – you cannot use the LED to confirm tach again.
You can however repeat the above steps to learn tach over again at any time.
11. Initializing the Remote Starter
BEFORE THE UNIT WILL DO ANYTHING FOR THE FIRST TIME, YOU MUST INITIALIZE
THE REMOTE STARTER
OPTIONAL STEPS
A. Insert the 30 amp fuse into the fuse holder on the large PINK wire.
B. Turn the control switch on.
C. The remote starter requires the installer to open the hood and then press and
hold the brake pedal. Note: The ignition/dash lights will come on if the unit is
not initialized.
D. While depressing the brake (with the engine off and the hood open) turn the
ignition key to the “RUN” (not “start”) position.
E. Put the car in “DRIVE” from the “PARK” position.
F. Put the car back in “PARK” and release the brake.
G. Turn the key off and remove the key.
13. Yellow Wire – Headlights/Parking Lights – Control Harness
Connection of the YELLOW wire allows you to activate the low beam headlights
or parking lights for remote start and lock status. After the remote starter has
started the car, the lights will remain on until the remote starter shuts off after 10
minutes, or when the brake pedal is pushed, or when the car is put into gear. This is
a relay +12 Volts output. Connect the YELLOW wire to the wire that has power
when the lights are on.
14. Blue – Horn/Siren – Control Harness
The BLUE wire signals the horn to honk (or siren to chirp) once each time the remote
starter starts the vehicle and each time the locks are locked or unlocked. Connect the
blue wire to the factory horn wire which is often found running down the steering
column. It will normally show +12 Volts at rest and the voltage will disappear when
the horn is honked. This is
a 400 mA transistor
Positive Horn/Siren Relay
ground output which
MUST drive a relay if
using a siren or
positively triggered
horn. Option #11 (section
24) must be changed when
using a siren.
Note: Confirm initialization by turning the ON/OFF control switch “OFF” and then
“ON”. The red LED light on the remote start module will flash once immediately as
the switch is flipped from the “OFF” to the “ON” position.
If the red LED light did not flash when the control switch was turned “ON” REPEAT
STEPS A THROUGH G. See the colored Trouble Shooting Sheets if necessary.
12A. Green Wire – Tach Input – Control Harness
The remote starter has two ways of monitoring the car during
the starting process. Both ways will ensure a clean, accurate start. Read about
both methods before deciding which one to use. Normally you should
try the “No Tach™” method first.
“No Tach™” Starting
This starting method does not require the connection of the GREEN tach wire. This
method will start the car by reading the car’s voltage before attempting to start, and
then looking for a voltage increase when the alternator kicks in. This feature
automatically takes into account voltage, temperature, and the time since the vehicle
was last run. The “No-Tach™”” starting is preset at the factory and you can skip step
12B if you would like to use it. Note that if the vehicle is hard to start, set Option #3
(section 24) for “extended crank.”
15. Brown/White – Alarm Disable/Starter Kill – Control Harness
The BROWN/WHITE wire is Alarm Disable, which will give out a quick negative
pulse just before starting the vehicle. This wire can be used to turn off the factory
alarm system in vehicles which have them. In most vehicles, this wire is located
in the driver’s kick panel.
Using Option #19 (section 24) you can set this to Starter Kill. This option prevents
the vehicle from being
Starter Kill Relay
started with the key
when the alarm is
Starter Wire
Starter Wire
From Key
To Starter
Cut
armed. It is also
Switch
Motor
active whenever the
Tap
into Blue
Remote Starter
vehicle is running
IGN1 Wire from
Brown / White
Remote Starter
Wire
under remote starter
Yellow Start Wire
control to provide From
Remote Starter
anti-grind protection.
Tachometer sensing
If the vehicle is generally hard to start (i.e. requiring a cranking time of more than 1
second) you will get more accurate starting with the tachometer sensing starting
method. This method starts the car by reading the engine speed (tach) information
from a wire under the hood. If you choose tachometer sensing, connect the GREEN
(18 awg) wire to the car’s tach wire under the hood (normally the negative side of the
coil or tach output of coil pack). After you have connected the GREEN wire, you need
to teach the remote starter the vehicle’s tach rate at idle. Proceed to step 12B.
87
86
Note: You must have already initialized the remote starter from Step 11.
87A
30
85
16. White/Black Wire – Ignition #3 – Control Harness
The WHITE/BLACK wire, is a ground output that acts just like the Ignition 1 or Ignition
2 relay outputs (active in the “run” and “crank” positions). This wire is a 400 mA
negative transistor output and MUST be set up to power a relay (not
included). It can be used to power the third ignition wire at the key (necessary for
most Ford vehicles).
12B. Tach Rate Learning
Note: Only use if the tachometer sensing method is chosen.
A. Connect the GREEN wire to the car’s tach wire under the hood.
B. Turn the On/Off control switch to the “OFF” position. Wait 5 seconds for the red
LED light flashes to stop.
C. Program the unit to the tach mode by pushing the White “option” button once
and watching the red LED light flash. Now push the start button on the transmitter
for a second until you see the red LED light flash again. You are now in TACH
mode. (If the red LED light flashed twice or sometimes three times – simply push
the transmitter button again until you get only one flash).
D. Wait 5 seconds for the red LED light to flash 3 times.
This is a wire that can also be used
to bypass a vehicle anti-theft system
by connecting it to the Universal
Alarm Bypass Module. See the
Factory Anti-Theft System section at
the end of the instructions.
3
Ignition 3
White/Black Wire
From
Remote Starter
To LARGE 12 Volt
Constant Wire
(Found in Ignition
Switch Wire
Harness)
87
85
87A
30
86
To Additional
Ignition Wire
(in vehicle)
v3.1 2428
17A. Yellow and White – Keyless Entry Wires – 3 Wire Harness
The alarm is “Last door arming.”
You should diode isolate the inputs
of two or more sensors on the same
input wire.
The wires function as follows:
YELLOW
WHITE
Negative Trigger – Unlock
Negative Trigger – Lock
Positive Trigger – Lock
Positive Trigger – Unlock
Positive Door Trigger
(Most Ford Vehicles)
Ground (-)
Door Pin Switch
(in vehicle)
87
85
87A
30
86
Determine the polarity of your door lock system by using a test meter. For NEGATIVE
locks (the lock wire sees a ground signal briefly as the electric locks are locked) –
connect the YELLOW wire to the Unlock wire and the WHITE wire to the Lock wire.
If you choose not to use this alarm
feature then permanently ground this
wire or program “No Alarm” Option
#24 (section 24).
For POSITIVE locks (the lock wire sees a +12 volt signal briefly as the electric locks
are locked but does not see ground when they are inactive) connect the YELLOW
wire to the Lock wire and the WHITE wire to the Unlock wire.
20. Red/Black Wire Diesel “wait to start” Control Harness
This wire is only used in diesel vehicle applications – and is optional. This
wire can be hooked up to the “wait to start” light’s switched wire behind the dash.
If Option #9 (section 24) is set, this wire will feed information to the remote starter
as to when to crank the vehicle over. This wire is not polarity sensitive.
For REVERSING POLARITY (the lock wires sees a +12 volt signal briefly as the electric
locks are locked and sees a ground signal when they are inactive) follow the
diagram below:
Vehicle Lock Wire
(Primary Switch Side)
Cut
(Actuator Side)
Cut
To 12 Volt
Constant
(15 Amp Fused)
87A
30
To 12 Volt
Constant
(15 Amp Fused)
Yellow Wire
From
Remote Starter
3-pin Harness
87
85
Note: You must have hooked up all required wires and completed Initialization
(Step 11) to proceed forward.
Vehicle Unlock Wire
(Actuator Side)
(Primary Switch Side)
White Wire
From
Remote Starter
3-pin Harness
REQUIRED FINAL STEPS
Reversing Polarity Door Locks
Unlock Relay
Lock Relay
86
21. Trying the Unit Out
87
85
87A
30
86
WARNING: Be prepared to apply the brake during this testing.
A.
B.
C.
D.
Close the hood and fully apply the emergency brake
Place the vehicle in Park.
Turn the On/Off switch off then on – the red LED light will flash once.
Once all the wiring is checked and is correct, press the Start button on the
transmitter.
E. The car should start and continue to run for ten minutes. Make sure that the
engine shuts down if the car is shifted out of park, the hood is opened, the brake
is pressed or the start button is pushed again. If the car does not start, see
Special Cases.
Most VACUUM operated door lock systems require Option #18 (section 24) for Long
locks to be set.
17B. Green Wire – Trunk Release – 3 Wire Harness
The GREEN wire is the Trunk Release output which gives out a transistor ground
output when the unlock button is held for 4 seconds. Again, this is a 400 mA
transistor ground output which MUST drive a relay (not included).
Negative Trunk Release
Positive Trunk Release
Ground (-)
Green Wire
From
Remote Starter
87
85
87A
30
To 12 Volt
Constant
(15 Amp Fused)
86
22. The Antenna
To 12 Volt
Constant
(15 Amp Fused)
Green Wire
From
Remote Starter
Feed the antenna around under the dash and up the inside of the right or left
windshield post and over the top of the windshield. Clean the windshield
with the provided alcohol pad for maximum adhesion. Let the windshield dry
completely. Peel the liner off the back of the adhesive tape and mount the
antenna behind the rear view mirror. The more exposed the antenna is, the
better the range performance. Finally, plug the end of the antenna into the
remote starter module. In most vehicles you will get better range performance if the antenna is pointing vertically downward from the top of the
windshield.
87
85
87A
30
86
To Positive
Trunk Release
(in vehicle)
To Trunk Release
(in vehicle)
18. Brown Wire – Accessory Pulse/Dome Light – Control
Harness
The BROWN wire is the Accessory Pulse output which gives out a momentary
transistor ground output 10 seconds after the vehicle is remotely started. This is
important in some vehicles to control the defroster or to control the GM R.A.P.
system. Again, this is a 400 mA transistor ground output which MUST
drive a relay (not included).
Note: The wiring section of the installation is now complete. Be sure to
cap all unused wires so as to prevent short circuits, and mount the
module securely under the dash. When tying up and mounting the unit,
be sure to avoid any moving parts (steering column, pedals) and sharp
edges.
This BROWN wire can also control a relay for Dome Light activation. When Option
#20 (section 24) is changed, this BROWN wire causes the dome light to turn on for
25 seconds every time the doors are unlocked with the transmitter.
Negative Dome Light
23. Trouble Shooting with the Self Diagnostics
Positive Dome Light
The remote starter contains a built in diagnostic routine that will indicate why the
unit started or why the unit turned off the car the last time that the unit was used.
(Most Ford Vehicles)
Ground (-)
Brown Wire
From
Remote Starter
87
85
87A
30
86
To 12 Volt
Constant
(15 Amp Fused)
To Negative
Door Pin
(in vehicle)
To 12 Volt
Constant
(15 Amp Fused)
Brown Wire
From
Remote Starter
To activate the diagnostic mode for why it turned off, simply turn the On/Off
control switch to the “OFF” position. In a few seconds, the red LED light on the
module will flash 1 to 12 times to identify the problem. See the chart below for an
explanation of the flashes:
87
85
87A
30
To Red/White Wire
from Remote Starter
86
To Positive
Door Pin
(in vehicle)
1 flash
10/15 minute time out. Unit should be fine. Make sure transmitter is
working properly.
The RED/WHITE wire is the Door Pin Alarm Input. This wire will accept any input
that supplies a negative (ground) when activated. (Most door pins go to ground
when the door is open, +12 Volts when closed.)
2 flashes
Unit turned off because Brake or Hood was activated. Check to make
sure the hood pin switch is depressed when the hood is closed and
the correct brake wire is hooked up.
Most Ford vehicles are positive door pins that switch to +12 Volts when opened, you
will need to reverse the polarity with a relay before connecting to this RED/WHITE
wire.
3 flashes
No Tach or Stalled. Review section 12 and make sure the no tach/tach
wire option is programmed correctly.
4 flashes
Received another remote input from the transmitter
19. Red/White Wire – Door Pin Alarm Input – Control Harness
v3.1 2428
4
28
29
30
31
N/A
N/A
N/A
N/A
N/A
N/A
Reset All Options
5 flashes
Transmission was shifted into gear. Cut the Green “In Gear Loop.”
See wire diagram on front cover.
6 flashes
Low battery voltage, or may be missing an ignition wire which
powers up the alternator
7 flashes
Alarm Input triggered
24B. Program Features Descriptions
8 flashes
Over current – One of the 400 mA (-) transistor outputs (Accessory
Pulse, Alarm Disarm, Starter kill, lock, unlock, horn, lights, trunk, or
Ignition 3) of the control harness is drawing too much current. Make
sure to use a relay where necessary.
Option #1
No-Tach
Tach Mode
This option sets the starting method. The factory setting uses “No-Tach” starting. If
you wish to use the tach to start, follow the instructions in the Tach Rate Learning
(section 12B).
12 flashes
The Control Switch was turned off while the starter was running.
Option #2
10 Min. Run Time
This option gives you a choice of run times.
For reasons why it last started, simply put your foot on the brake while you turn
the control switch OFF. Keep holding the brake down until the flashes start. The
codes are as follows:
1 flash
The unit has not started yet since it was last powered up.
2 flashes
Received a radio signal from the transmitter to start.
3 flashes
N/A
4 flashes
Temp reached 0o F in vacation mode.
5 flashes
Voltage reached 11 volts in Vacation Mode.
6 flashes
Received a start command from the remote input RED/BLACK wire.
7 flashes
Started from 24 hour Daily Start feature.
Option #3
Normal Crank
Extended Crank
This option will add 50% more crank time to the NoTach™ starting feature.
Option #4
Normal
IGN 2 not active during Crank
This option will turn off the Ignition 2 output (thick GREEN wire) during cranking. It
is used to exactly match the remote starter with the ignition key function.
Option #5
Normal Voltage Metering
Ignore Voltage Metering
This option is used in the “No-Tach” starting method for some diesel vehicles or
vehicles with weak batteries and/or poorly performing altenators.
Option #6
Gasoline Vehicles
Diesel Vehicles
This option must be activated when installing on a diesel vehicle.
24A. Setting Program Features
The remote starter unit has many special features available. You will not need to use
these special features in most situations. The factory settings will operate most
vehicles. You must turn the On/Off control switch to the “OFF” position to
program any features.
Option #7
“Enable” Feature
No “Enable”
This option cancels the “enable” mode safety feature. The “enable”
mode requires that the driver toggle the ON/OFF control switch “OFF”
then “ON” each time the driver removes the key from the ignition in
order to “enable” the vehicle for remote starter control. This feature
guards against undesired starting of the vehicle by remote control. For
vehicles manufactured prior to 1996, please see the important warning
on the last page of these instructions.
Note: When turning off this control switch, the red LED light will flash a few times,
giving the diagnostic code described in section 23. Wait a few seconds for it to
finish before programming your new Options.
Feature
Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Factory Setting
(2 flashes)
“No-Tach”
10 Min. Run Time
Normal Crank
Normal
Normal Voltage Metering
Gasoline vehicles
“Enable” feature
Normal
Normal
1 sec. alarm disarm pulse
Horn Pulsing
Chirp with Locks
Active
Normal
Normal
Normal
Normal
Short Locks
Alarm Disable
Accessary Pulse
N/A
N/A
N/A
Alarm Mode
N/A
N/A
N/A
15 Min. Run Time
Option
(1 flash)
Tach Mode
15 Min. Run Time
Extended Crank
IGN 2 not active during crank
Ignore Voltage Metering
Diesel vehicles
No “Enable”
Daytime Running Lights
Diesel “Wait to Start”
0.45 sec. Alarm disarm pulse
Siren Constant
Silent lock/Unlock/Start
Passive Arming
Lock Follow ignition
Unlock Follow ignition
Double Pulse Lock
Double Pulse Unlock
Long Locks
Starter Kill
Dome Light
N/A
N/A
N/A
No Alarm Mode
N/A
N/A
N/A
Option #8
Normal
Daytime Running Lights
This option will automatically turn the headlights on (for safety) about 10 seconds
after it sees the key in the ignition position – and automatically turn the headlights off
when the key is removed from the ignition.
Option #9
Normal
Diesel “Wait to Start”
This option will control the time before cranking the diesel vehicle by looking at the
“wait to start” light of the vehicle. Simply hook the RED/BLACK Input wire of
section 20 up to the wire behind the “wait to start” light. Also set Option #6 (section
24) for diesel vehicles.
Option #10
1 sec. Alarm Disarm Pulse
0.45 sec. Alarm Disarm Pulse
This option shortens the Alarm Disarm Pulse from 1 second to 0.45 second. This
feature is very useful with some Dodge/Chrysler vehicles that use a multiplexed
system to disarm the alarm and unlock the doors with the same wire. Using this
feature should eliminate the need to relock the doors after the alarm has been
disarmed and the vehicle is remotely started.
Option #11
Horn Pulsing
Siren Constant
This option changes the thin BLUE wire from pulsing output for horn to constant
output for a siren.
Option #12
Chirp with Locks
Silent lock/Unlock/Start
This option will eliminate the chirp with Start, Lock and Unlock.
Option #13
Active Arming
Passive Arming
The factory setting of Active Arming requires the owner to actively arm the car with
the remote control. Choosing the option of Passive Arming will cause the vehicle
to automatically arm after the key is removed and the door is closed.
5
v3.1 2428
Option #14
Normal
Lock Follow Ignition
Selecting this option will automatically lock the doors when the key is turned on,
doors closed and the brake is depressed.
C.
Option #15
Normal
Unlock Follow Ignition
Selecting this option will automatically unlock doors when key is removed from
ignition.
You can choose to change another feature by starting over again at Step A. After
six seconds, the remote starter automatically exits the programming mode
(three LED light flashes).
D.
When finished – switch the Control Switch back ON. The red LED light will flash
once.
twice to signify you are at the Factory setting. Push the transmitter button again
and you will go back to the Option setting.
Option #16
Normal
Double Pulse Lock
This option will pulse the lock output wire twice instead of once for normal mode.
25. External shock sensor hook up (included with model 2xx28
only):
Option #17
Normal
Double Pulse Unlock
This option will pulse the unlock output wire twice instead of once for normal mode.
Plug the shock sensor unit into the 3 wire connector on the front side of the remote
start module. Use one or two cable ties to tightly fasten the shock sensor unit to the
steering column of the vehicle. Make sure that the sensor does not affect the
driver's ability to steer the vehicle.
3-Pin External Alarm Sensor
This placement gives the best overall
coverage for a vehicle. Adjust the
Control Harness
1
2
3
on this side
screw(s) so that a hard impact on the
vehicle triggers the full alarm and light
1. +12 Volts, when armed
2. Ground
impacts just trigger the warn away.
3. Full Alarm
(This input may not work with all types
of alarm sensors.)
Option #18
Short lock pulse
Long lock pulse
This option will increase the door lock pulse time from 0.6 second to 3 seconds for
vehicles with vacuum locking systems (older European vehicles).
Option #19
Alarm Disable
Starter Kill
The factory setting of Alarm Disable will give you a quick pulse whenever the
transmitter unlocks the doors or the transmitter is used to start the vehicle. The Starter
Kill option comes on and stays on whenever the remote starter is running or the
alarm is armed. This wire controls a relay which opens up the path of the starter wire
(refer to section 15).
SPECIAL CASES
Option #20
Accessory Pulse
Dome Lamp
Accessory pulse puts out a brief pulse output after the remote starter starts or stops
the vehicle. When set, this output can be used to turn on a defroster that requires a
momentary pulse or could be used to control GM R.A.P. (retained accessory power)
output. Dome lamp option will turn this output on when you unlock the door for 25
seconds. (Refer to section 18).
1. How to Use a Relay
Many of the optional steps require a relay to be hooked up. The most common relay
used for this type application is the Bosch type relay (DesignTech #20043 or Radio
Shack Cat.# 275-226). Use the diagram below for a typical hookup. If you have
another relay then you need to know that pins 85 and 86 in this diagram relate to the
coils of the relay. Pin 30 is the ‘common’, and pin 87 is the ‘normally open’ contact.
If your relay has a pin 87A in the middle it is the normally closed contact and is only
used for reverse polarity door locks. (The diagram below is typical for an Ignition 3
or trunk application).
Option #24
Alarm
No Alarm
This feature can disable all alarm functions if the alarm features are not desired.
Option #31
Reset all Options
This option resets all options back to the factory settings.
PROGRAMMING AN OPTION
If you want the factory setting, DO NOTHING and skip this section. If you want to
change one or more of the features, TURN THE ON/OFF CONTROL SWITCH TO THE
“OFF” POSITION. Wait for the red LED light to stop flashing, then continue
with the following procedures:
A.
B.
From
Remote
Starter
(-)
To supply +12 volt output
To supply Ground (-) output
+12 V
To Ground
87
+12 V
30
85
86
From
Remote
Starter
(-)
87
+12 V
30
85
86
For options 1-9: Push the white code button on the remote start module. Each
time you push the button the red LED light will flash 1 to 9 times signifying at
which feature you are (press it once, the LED light flashes once. Press it again
and it will flash two times. Press it again and it will flash three times, etc., to
show what feature you are at).
2. Code Learning
For options 10-19: Push the red code button on the remote start module. You
will see the LED light flash a long blink. This is option 10. You can scroll to
option 11 by pressing the white button once – you will see a long blink followed
by one short blink. You can scroll to option 12 by pushing the white button
again – one long and two short blinks brings you to option 12.
Your transmitter is factory coded to the remote starter module with over 16,000,000
different codes. The remote starter module can learn the codes of up to 4 different
transmitters. If you want to add additional transmitters to the receiver or if it does
not respond to your transmitter – follow the steps below to teach the receiver
the transmitter code(s):
For options 20-29: Push the red code button twice to get the two long blinks –
you are now at option 20. Push the white button to jump ahead to option 21 –
two long blinks and one short blink. Push three more times to get to option 24
– two long and four short blinks.
A. Turn the Control Switch ON.
For options 30-31: Push the red code button three times to get three long blinks
– you are now at option 30. Push the white button once to jump to option 31
(three long blinks and one short blink).
C. While holding the transmitter at least three feet from the module, hold down the
Start button (on a five button transmitter) or the lock/unlock button (on a three
button transmitter) until the red LED light and the dash lights come on again for
a second. The module has now learned the transmitter code. Release the
transmitter button.
To Vehicle's Accessory
B. Push the red "code learn" button to the right of the red LED light. The red LED
light and the dash lights come on for a second. (The vehicle's ignition and
accessory wires come on).
When you are at the feature level you desire, push the start button on the
transmitter for one second and the red LED light will flash once to signify you are
at the Option setting. You can push the transmitter button again and it will flash
v3.1 2428
To Vehicle's Accessory
D. To learn additional transmitters (up to 3 more), immediately (within 5 seconds)
push the Start button (on a five button transmitter) or the lock/unlock button (on
6
a three button transmitter) on another transmitter for a few seconds until the red
LED light and the dash lights come on for a second again.
LIST OF VEHICLES AND THE TYPES OF FACTORY ANTI-THEFT SYSTEMS
Vehicle
E. 5 seconds after the last time the transmitter was learned the unit exits the
code-learning stage. (The red LED light, ignition and accessories flash 4 times).
Acura 3.2TL 98+ .......................... Transponder
Audi A4,A6,A8 98+ ...................... Transponder
Acura CL 97+ ............................... Transponder
Acura Integra ............................... Transponder
Acura NSX ................................... Transponder
Acura RL 98+ .............................. Transponder
BMW (all 97 +) ............................ Transponder
Buick LeSabre 90 - 01 ................. VATS
Buick Park Ave 91 - 96 ................ VATS
Buick Park Ave 97+ ..................... Transponder
Buick Regal 93 -96 ...................... VATS
Buick Rendez Vous ...................... Transponder
Buick Riviera 93 -96 .................... VATS
Buick Roadmaster 93 - 96 ........... VATS
Buick Skylark 96-98 .................... Passlock
Cadillac Allante ............................ VATS
Cadillac Brougham ...................... VATS
Cadillac Catera 97+ ...................... Transponder
Cadillac DeVille 92 - 98 ............... VATS
Cadillac DeVille 99+ ..................... Transponder
Cadillac Eldorado 89 - 98 ............ VATS
Cadillac Eldorado 99+ .................. Transponder
Cadillac Escalade 00+ .................. Passlock
Cadillac Fleetwood 90 - 96 .......... VATS
Cadillac Seville 90 - 98 ................ VATS
Cadillac Seville 99+ ..................... Transponder
Chevrolet Astro Van 98+ .............. Passlock II
Chevrolet Avalanche 01 ............... Passlock
Chevrolet Blazer 98+ ................... Passlock II
Chevrolet Camaro 86 + ................ VATS
Chevrolet Cavalier 96-99 ............. Passlock
Chevrolet Cavalier 2000+ ............. PasslockII
Chevrolet Corvette 88 + ............... VATS
Chevrolet Express 97+ ................. Passlock
Chevrolet Impala 2000+ .............. Passlock II
Chevrolet Lumina 96 -99 ............. VATS
Chevrolet Malibu 97 -01 .............. Passlock II
Chevrolet Monte Carlo 96-99 ...... VATS
Chevrolet Monte Carlo 00+ .......... Passlock II
Chevrolet Pickup Full-size 98+ .... Passlock II
Chevrolet S-10 98+ .................... Passlock II
Chevrolet Silverado HD 01 .......... PasslockII
Chevrolet SSR 01 ........................ Passlock
Chevrolet Suburban 98+ .............. Passlock II
Chevrolet Tahoe 98+ .................... Passlock II
Chevrolet Trailblazer 01+ ............. PasslockII
Chevrolet Van 98+ ....................... Passlock II
Chevrolet Venture 99+ ................. Transponder
Chrysler Concorde 98+ ................ Transponder
Chrysler LHS 99+ ........................ Transponder
Chrysler PT Cruiser 00+ .............. Transponder
Chrysler Sebring Conv. 98+ ........ Transponder
Daewoo Leganza ......................... Transponder
Dodge 300 M 99+ ........................ Transponder
Dodge Intrepid 98+ ..................... Transponder
Dodge Neon 00+ ......................... Transponder
Ford Contour 97 + ....................... Transponder
Ford Crown Victoria 98+ (option) Transponder
Ford Excursion 01+ .................... Transponder
Ford Expedition 97+ .................... Transponder
Ford Explorer 98+ ........................ Transponder
Ford Focus 01+ ........................... Transponder
Ford Mustang 98+ ....................... Transponder
Ford Pick Up (optional) ............... Transponder
Ford Ranger 99+(optional) .......... Transponder
Ford Sport Trac 01 ....................... Transponder
Ford Taurus 96 + ......................... Transponder
Ford Windstar 2000 + .................. Transponder
GMC Envoy 01+ ........................... Passlock II
GMC Jimmy 98+ ......................... Passlock II
GMC Safari 98+ ........................... Passlock II
GMC Denali 99+ .......................... Passlock II
Note: Teaching the module a new transmitter code will erase all previous codes –
so all transmitters must be taught. You have only 5 seconds between transmitters
to begin teaching a new transmitter.
3. Diesel Vehicles
For the most reliable starting of diesel vehicles, hook up the RED/BLACK wire
referenced in section 20. This wire can be difficult to hook up but is not required.
For difficult starting diesels connect and learn the tach (section 12) as well as the
wait-to-start RED/BLACK wire (section 20). Set option 6 (section 24) for diesel
vehicles.
For most diesel vehicles, you can start the vehicle without needing to hook up a tach
wire. The following table provides the mandatory option settings for “no-tach”
operation in diesel vehicles. (Use the Chrysler settings for all other diesel vehicles.)
Option #6
Diesel
Engine
Option #3
Extended
Crank
Chrysler
■
■
Ford
■
■
■
Chevrolet
■
■
■
System
Option #5
Ignore
Meter
4. Factory Anti-Theft Systems
Many vehicles come with an anti-theft system that must be temporarily bypassed for
the vehicle to be remotely started. Some systems use a resistor in the key. Others
use a transponder – a small device in the key that communicates a high security
code to the vehicle before the vehicle will successfully start.
Check the list of vehicles and the types of security systems. If your vehicle is listed,
your vehicle has an Anti-Theft System that the remote starter MUST temporarily
bypass in order to start the vehicle. More information about the factory anti-theft
systems and vehicle wire colors can be found on the DesignTech Website at
www.designtech-intl.com.
DesignTech has developed a Universal Alarm Bypass Module sold under the following
model numbers: #20402, #27402, or #29402. This module will temporarily bypass
the factory anti-theft systems when using the remote starter. Check with your local
retailer/installer to purchase this Universal Alarm Bypass Module or contact
DesignTech directly.
7
Vehicle
System
GMC Sierra .................................. Passlock II
GMC Sonoma 98 + ...................... Passlock II
GMC Suburban 98+ ..................... Passlock II
GMC Yukon 98+ .......................... Passlock II
Honda Accord 98+ ....................... Transponder
Honda Odyssey 98+ .................... Transponder
Honda Prelude 98+ ...................... Transponder
Honda S2000 .............................. Transponder
Infiniti I30 98+ ............................. Transponder
Infiniti Q45 98+ ........................... Transponder
Infiniti QX4 .................................. Transponder
Jaguar (all 98+) ........................... Transponder
Isuzu Hombre 98+ ....................... Passlock II
Jeep Grand Cherokee 99+ ........... Transponder
Jeep Liberty ................................. Transponder
Jeep TJ (Wrangler) 99+ ............... Transponder
Lexus (all 97+) ............................ Transponder
Lincoln Blackwood ...................... Transponder
Lincoln Continental 97+ ............... Transponder
Lincoln LS 2000+ ........................ Transponder
Lincoln Mark VIII 97+ .................. Transponder
Lincoln Navigator 97+ ................. Transponder
Lincoln Town Car 97+ .................. Transponder
Mazda Tribute .............................. Transponder
Mercedes (all 97+) ...................... Transponder
Mercury Cougar 99+ ................... Transponder
Mercury Grand Marquis .............. Transponder
Mercury Mountaineer 98 + .......... Transponder
Mercury Mystique 97+ ................ Transponder
Mercury Sable 96+ ...................... Transponder
Mini Cooper 02 ............................ Transponder
Mitsubishi Eclipse ....................... Transponder
Mitsubishi Galant ........................ Transponder
Nissan Frontier S/C ..................... Transponder
Nissan Maxima 98+ ..................... Transponder
Oldsmobile Achieva 95 ................ Passlock I
Oldsmobile Achieva 96+ .............. Passlock II
Oldsmobile Alero 99+ .................. Passlock II
Oldsmobile Aurora ...................... VATS
Oldsmobile Bravada 98 ............... Passlock II
Oldsmobile Cutlass 97+ .............. Passlock II
Oldsmobile Eighty-Eight .............. VATS
Oldsmobile Intrique 98+ .............. Passlock II
Oldsmobile Ninty-Eight ................ VATS
Oldsmobile Silhoutte 99 .............. Transponder
Pontiac Aztek 01 .......................... Transponder
Pontiac Bonneville 89+ ................ VATS
Pontiac Firebird 88+ .................... VATS
Pontiac Grand Am 96 - 98 ........... Passlock
Pontiac Grand Am 99+ ................ Passlock II
Pontiac Grand Prix 92 – 96 ......... VATS
Pontiac Grand Prix 97+ ............... Transponder
Pontiac Montana 99+ .................. Transponder
Pontiac Sunfire 96-99 ................. Passlock I
Pontiac Sunfire 2000+ ................. Passlock II
Porsche (all 97+) ......................... Transponder
Saab (all 97+) .............................. Transponder
Saturn 97-99 ............................... Factory
Saturn 00+ .................................. Transponder
Subaru Legacy 00+ ..................... Transponder
Subaru Outback 00+ .................... Transponder
Toyota Avalon 98+ ....................... Transponder
Toyota Camry 98+ ....................... Transponder
Toyota Highlander 01+ ................ Transponder
Toyota Land Cruiser 98+ ............. Transponder
Toyota Solara 99 + ....................... Transponder
Toyota Supra 98+ ........................ Transponder
Volkswagen Beetle 98+ ................ Transponder
Volkswagen Golf 98+ ................... Transponder
Volkswagen Passat 98+ ............... Transponder
Volvo (all 98+) ............................. Transponder
v3.1 2428
NOTICE to Installers of Remote Vehicle Starters
DesignTech International DOES NOT recommend installing ANY remote starter in the following vehicles: Audi 1998+, BMW 1998+,
Jaguar 1998+, Land Rover 1998+, Mercedes 1998+, Range Rover 1998+, Volvo 1999+
As with any aftermarket installation, please research and learn as much as you can about the vehicle before you start the install.
All General Motors (GM) vehicles (with rear wheel drive) built prior to 1995 with automatic transmissions and all Dodge Dakota trucks with
4 cylinder engines and automatic transmissions built prior to 1996 have a MECHANICAL type of NEUTRAL SAFETY SWITCH. All vehicles
built after 1996 use an electrical type of neutral safety switch.
Applying +12 volts to the starter wire on any vehicle vehicle using a mechanical neutral safety switch will engage the vehicle’s starter, regardless of the shifter’s position. When
the shifter is in Park or Neutral, the vehicle will just start up normally. If the vehicle is accidentally left in gear and power is applied to the start wire, such as by a remote starter,
the vehicle will lurch forward or back as it attempts to start.
To test if your GM or Dodge vehicle is using a mechanical neutral safety switch system, you will only be able to remove the key from the ignition switch
when the shifter is in the Park or Neutral position.
To prevent this problem from occurring when installing a DesignTech International remote starter on the above mentioned GM vehicles or Dodge Dakota
vehicles:
1. You must leave the Enable Feature (option #7) in the factory setting. This is a safety feature that requires the user to turn the control switch OFF and then ON again each
time they exit the vehicle in order for the unit to be operational. This feature will ensure that the user of the vehicle with the remote starter installed has made a conscious
decision to allow the remote starter to start the vehicle the next time the transmitter button is depressed.
2. You must use the relay drawing below to create a circuit that will prevent the remote starter on these GM and Dodge vehicles from starting the vehicle unless the key is
completely removed from the ignition switch.
87
Connect to
constant
(+) 12 volts
85
To (-) Vehicle's Ground
87a
86
30
Connect to the
Ignition Key Sense
Wire from Vehicle's
Ignition Harness
Connect to Purple Wire (hood pin
switch) of the Remote Starter
(Purple Wire must also connect to
hood pin switch)
As with any aftermarket installation, please research and learn as much as you can about the vehicle before you start the install. Instructions, technical tips and detailed wiring
information is available on our web site: www.designtech-intl.com. Please refer to the information on the web site before starting ANY install or call DesignTech Technical
Services at (800) 337-4468 or (703) 866-2000.
7955 Cameron Brown Ct. • Springfield, Virginia 22153 USA
Tel: (703) 866-2000 or (800) 337-4468 www.designtech-intl.com
PLEASE HAVE MODEL NUMBER AND DIAGNOSTIC CODES
READY BEFORE CALLING TECH SUPPORT
v3.1 2428
8
USER TIPS AND NOTES
The Remote Car Starter must be “enabled” each time the driver has finished driving and
taken out the key in order for the unit to start the vehicle remotely. After the key has been
removed, you must turn OFF the control switch and then turn it back ON again while no key is in the
ignition. This “control switch” or “set switch” prevents unauthorized starting of the car by someone
unfamiliar with the system who may be using the vehicle. If you forget to set the switch, it may also be
activated by pushing the transmitter and holding the button down for ten seconds. To eliminate the need
for this, see Option #7.
The AutoCommand® Professional Series Remote Car Starter will turn the car off if the driver does not
insert and turn the key within 10 or 15 minutes. After the remote car starter has started your car, simply
put in the key and turn it to the “run” or “on” ignition position (not the crank position) to drive away.
The AutoCommand® Professional Series Remote Car Starter has numerous safety and security features
that make it difficult to steal your car without the key being in the ignition. Putting your car in gear,
tapping the brake pedal or opening the hood will turn the unit off unless your key is in the ignition and
turned to the “run” or “on” position.
Button 2:
Button 1:
Once: Start the car with all accessories left on
Again: Stop the car
Pressed Once: Lock the door / arm the alarm
Pressed Again: Unlock doors / disarm the alarm
Hold down for 4 seconds for Panic
If all features are hooked up, your transmitter will function as follows:
Button 3:
Once: Turn on the headlights for 30 seconds
Again: Turn off the headlights
Hold down for 4 seconds to open the Trunk.
The LED light on the transmitter will display 3 different colors – Green for Button #1, Red for Button #2,
and Yellow for Button #3. The transmitter is powered by a long life lithium battery (CR 2032 or DesignTech
catalog # 20059). The transmitter and the remote starter receiver module are FCC and DOC approved.
Alarm Disarm without transmitter: If the doors are locked and the alarm is set and you’ve lost your
transmitter, you can disable the alarm. Here is how: Enter the vehicle (alarm will sound) and insert the
key and turn it to the ‘run’ position (the position where the dash lights come on). Turn the On/Off switch
off and on 4 times in a row to disable the alarm.
Valet Mode: Turning the Control switch off puts you in Valet Mode. In Valet Mode the Remote Car
Starter and the alarm will not function. This lets you turn off the car starter when having the vehicle
serviced. The only functions that work in Valet Mode are the keyless entry, lights and panic. The red LED
dash light will flash twice every few seconds when in Valet Mode.
The Quick Stop Option™: You can leave the car running and take the key with you for a quick visit to
a store. With the car running, push the Start button on the keychain transmitter just before pulling out the
key. The car will run for 10 minutes or until you tap the brake or put the car in gear.
The Cold Start Option™: This automatically starts and runs the car for the preset run time (10 or 15
minutes) if the temperature drops below 0°F or if the battery voltage drops below 11 volts. Tapping the
brake at any time after programming disables this feature. Here is how to set this feature: Hold the Start
button down while the vehicle starts, runs, turns off and the lights begin to flash 5 times. Release the
transmitter button. You have set the Cold Start Option™.
OUT OF WARRANTY REPAIRS
LIMITED LIFETIME WARRANTY
DesignTech International, Inc. Warrants to the original consumer/purchaser that this product shall be
free of defects in material and workmanship under normal use and circumstances for the period of
time that the original owner of this product owns the vehicle in which it is installed. When the
original consumer/purchaser returns the product pre-paid to DesignTech International Inc., 7955
Cameron Brown Court, Springfield, Virginia 22153, USA within the warranty period, and if the
product is defective DesignTech International, Inc. will at its option repair or replace such.
This warranty shall constitute the sole liability of DesignTech International, Inc. concerning the product.
DesignTech International, Inc. expressly disclaims all other warranties INCLUDING, WITHOUT
LIMITATION, THE WARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A PARTICULAR PURPOSE. NO PERSON, FIRM , OR CORPORATION IS AUTHORIZED TO ASSUME
FOR DESIGNTECH INTERNATIONAL, INC. ANY OTHER LIABILITY IN CONNECTION WITH
THE SALE AND USE OF THE PRODUCT. DesignTech International, Inc. and agents and distributors will bear no liability whatsoever for incidental or consequential damages or charges of any kind.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above disclaimer regarding incidental or consequential damages may not apply to you.
Please completely fill out the warranty registration card below and mail with copy of proof of purchase
to: DesignTech International, Inc., 7955 Cameron Brown Court, Springfield, Virginia 22153-2809,
USA within ten (10) days after date of purchase.
This warranty is void if the product or has been damaged or tampered with or if the product or any such
parts have been opened. In all cases of damage during shipment, a claim must be filed with the shipping
carrier and not with DesignTech International, Inc.
This warranty gives you specific legal rights; you may also have other rights which vary from state to
state.
If the warranty card was not returned, or if you are not the original owner of the vehicle the product
was installed in, DesignTech International, Inc. will at its option either (1) replace this product with a
functionally similar (but not necessarily visually identical) refurbished product or (2) repair the original product and return it to the original consumer/purchaser after payment of repair/replacement
charges have been received.
Please return this warranty registration card within ten (10) days of purchase.
Name_________________________________________________________ User's Age_________
Address _________________________________________________________________________
Home___________________________
Date of Purchase________________
Office_______________________
City____________________________________ State__________________ Zip_______________
Phone Number:
Place of Purchase__________________________________
( ) Spouse
( ) Relative
( ) Friend
Product Purchased:_________________________________Price of Purchase:____________
( ) Myself
Vehicle Make:__________________Vehicle Model:________________Year:__________
This product was purchased for:
( ) In-Store Display
( ) Mail Order
( ) Magazine Ad
( ) Other _____________________
( ) Retailer Newspaper Ad
How did you first become interested in this product?
( ) Newspaper / Magazine Article
( ) Friend / Relative
( ) In-Store Salesperson
7955 Cameron Brown Court, Springfield, Virginia 22153, USA
Tel: 703-866-2000 Fax: 703-866-2001
__________ Please send me FREE information on other innovative DesignTech products.
v3.1
7955 Cameron Brown Court
Springfield, VA 22153-2809
Place
Stamp
Here
Daily Start™: This allows you to start the vehicle at the same time the next day. For example, if you
leave for work at the same time each morning you can use the Daily Start™ feature to automatically start
your car the next day. Here is how: Start your car with the transmitter as usual. When you enter the
vehicle and before you put the key in the ignition, put your foot on the brake to turn the AutoCommand®
off. Now within five seconds toggle the control switch off and on once while your foot is still on the
brake. The dash lights will flash once to signal the setting of this option. Your vehicle will now start
approximately 23 hours and 50 minutes later and run its normal cycle. You can still start the vehicle with
the key or via the transmitter anytime without cancelling out this option.
Safety Notices:
1. When taking your car in for any service or repairs, disable the remote starter by switching the Control
switch to the OFF position. Inform the mechanic.
2. Never leave your keys in the Ignition when the vehicle is unattended.
3. Do not use this product in a closed garage to avoid excessive carbon monoxide build-up.
Available Accessories:
Product
Universal Alarm Bypass Module
(also goes by part no. 27402 or 29402)
Extra 3 button transmitter
Extra Lithium Transmitter Battery
Long Range Cellular Style Antenna
Garage Door Receiver Unit
Bosch 30 amp relay
3 Pin Shock Sensor
Siren
$49.95
$ 7.95
$59.85
$49.95
$ 9.95
$49.95
$49.95
Cost in US$
$39.95
Universal Alarm Bypass Module allows remote car starter installation on newer vehicles with factory
anti-theft systems such as VATS, P.A.T.S., Passlock I, Passlock II, Pass-Key III, Saturn, Securlock, and
Transponder systems.
Extra transmitters for more than one user in the family. Up to four transmitters can be used with each
receiver in the vehicle.
Our Garage Door Receiver hooks into your existing garage door system and lets your transmitter open
your garage. Part #30021.
Our Long Range Antenna doubles your range. Part #20314.
These products can be purchased through your dealer or directly from DesignTech International, Inc.
Part No.
20402
25561
20059
20314
30021
20043
20610
20405
7955 Cameron Brown Ct. • Springfield, Virginia 22153 USA
Tel: (703) 866-2000 or (800) 337-4468 www.designtech-intl.com
PLEASE HAVE MODEL NUMBER AND DIAGNOSTIC CODES
READY BEFORE CALLING TECH SUPPORT
Download PDF

advertising