1 Port RS232 Serial over IP Device Server

1 Port RS232 Serial over IP Device Server
NETRS232
*actual product may vary from photos
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 09/10/2015
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
Table of Contents
Introduction.............................................................................................1
Packaging Contents.................................................................................................................................. 1
System Requirements............................................................................................................................... 1
Product Diagram.....................................................................................2
Front View..................................................................................................................................................... 2
Rear View....................................................................................................................................................... 2
DB-9 Connector Pinout..........................................................................3
RJ-45 Connector Pinout.........................................................................3
Installation...............................................................................................4
Hardware Installation............................................................................................................................... 4
Software Installation................................................................................................................................. 5
Operation.................................................................................................5
Specifications...........................................................................................8
Technical Support...................................................................................10
Warranty Information.............................................................................10
Instruction Manual
i
Introduction
Packaging Contents
• 1xSerial over IP Device Server
• 1xDIN Rail Kit
• 1xTerminal Block
• 1xUniversal Power Adapter (NA/UK/EU) and AU in Australia
• 1xSoftware CD
• 1xInstruction Manual
System Requirements
• RJ45 terminated Cat5 or higher Ethernet cabling
• 10/100Mbps compatible Ethernet network
• Windows® 8 / 8.1 (32/64bit), 7 (32/64), Vista(32/64), XP(32/64), 2000, Windows®
Server 2012, 2008 R2, 2003(32/64)
Instruction Manual
1
Product Diagram
Front View
Power LED
Transmit LED
Receive LED
Power Jack
(10~30V DC)
DB-9 Serial Port
Rear View
RJ45 10/100 Port
Terminal Block
(10~30V DC)
Instruction Manual
2
DB-9 Connector Pinout
1
5
6
9
Pin 1
DCD
Pin 2
RXD
Pin 3
TXD
Pin 4
DTR
Pin 5
GND
Pin 6
DSR
Pin 7
RTS
Pin 8
CTS
Pin 9
RI
PIN
Define
1
TX+
RJ-45 Connector Pinout
Instruction Manual
3
2
TX-
3
RX+
6
RX-
Installation
Hardware Installation
DIN-Rail Bracket:
Follow the below procedure to install the DIN-Rail bracket to the RS232 device server.
1. Remove the included DIN-Rail bracket, and screws from the package, and align the
DIN-Rail bracket flush onto the back of the device server.
2. Align the bracket’s mounting holes with that of the device servers pilot holes, and
secure the bracket to the device server with the two included screws.
DIN-Rail Mounting:
Follow the below procedure to mount the device server to a DIN-Rail.
1. Tilt the unit, making sure that the metal spring located at the back is positioned on
top of the DIN rail.
2. Push the unit towards the rail until a “click” sound is heard.
Connecting to Terminal Block Power:
The device server is powered by an included Universal Power Adapter, or a 2-wire
10~30V DC power source via the included terminal block.
1. Attach the included power adapter to an AC power source, or follow the below
procedure for terminal block power setup.
2. Gently, yet firmly pull the terminal block connector housing from the device server.
3. Using a small flat head screw driver, loosen the screws for the terminal block
connectors.
4. Connect the power and ground wires from your DC power source to the proper
terminal block connectors and fasten the screws. The terminals are marked on the
device server housing.
5. Reinsert the terminal block housing into the device server
Instruction Manual
4
Software Installation
1. Connect the device server’s RJ45 interface to your Local Area Network (LAN).
Note: Alternatively, you can also use a crossover cable to connect the device server
directly to your system for the initial configuration.
2. Insert the provided CD into your DVD/CD-ROM drive.
3. Browse to the folder “\VCOM driver” and execute the “vcomsetup.exe” installer.
4. Follow the on-screen instructions to complete the installation of the VCOM and
WinPcap software.
Operation
1. Start the software by launching the VCOM shortcut.
2. Click the Search button in the VCOM software window to locate the device.
Instruction Manual
5
3. If required, allow access to the software through the Windows Firewall by clicking
the “Allow access” button.
4. Once the device is found, configure the PC to the same IP domain by clicking the
“Configure” button. The default IP address of the device is “192.168.1.1”.
Note: The default Gateway Address is “192.168.1.254”.
5. In the “Input Attributes” dialog, enter the following:
•Account Name: admin
•Password: 00000
6. Once the device is connected, the “Configure Dialog” will open to set your desired
IP settings.
Instruction Manual
6
7. Once your settings have been customized, click the “OK” button at the bottom of
the screen.
Instruction Manual
7
Specifications
Interface
Serial
Industry Standards
IEEE 802.3, IEEE 802.3u
Ports
1
Connectors
1x DB-9 (9 pin; D-Sub) Male
1x RJ-45 Female
1x Terminal Block (2 wire)
1x DC Power
Auto MDIX
Yes
Compatible Networks
10/100 Mbps
Data Bits
5, 6, 7, 8
Flow Control
RTS/CTS, None
Max Baud Rate
230.4 Kbps
Parity
None, Even, Odd, Space, Mark
Remote Management Ability
Yes
Serial Protocols
RS-232
Stop Bits
1, 2, 1.5
Supported Protocols
VCOM, TCP Server, TCP Client, UDP, HTTP,DHCP,
ICMP(PING), Static IP, ARP
Enclosure Type
Plastic
Product Dimensions (LxWxH)
86mm x 54mm x 23mm
LED Indicator(s)
1x Power
1x Tx
1x Rx
1x 10/100 Mbps Indicator
1x Link / Activity
Instruction Manual
8
Power Input
Terminal Block: 10~30V DC (2 wire)
DC Jack: 10~30V DC 3.5mm
Power Consumption
1.45W Max
Enclosure Material
Plastic
Operating Temperature
0°C to 60°C (32°F to 140°F)
Storage Temperature
-10°C to 70°C (-14°F to 158°F)
Humidity
0~90% RH
Product Weight
2.29 oz (65 g)
Compatible Operating
Systems
Windows® 8 / 8.1 (32/64bit), 7 (32/64),
Vista(32/64), XP(32/64), 2000, Windows® Server
2012, 2008 R2, 2003(32/64)
Instruction Manual
9
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
officers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Instruction Manual
10
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you find the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.
Download PDF