52RV535U_EN.book Page 1 Tuesday, July 22, 2008 5:25 PM
Pre-final version
Printing version
Integrated High Definition
LCD Television
HIGH-DEFINITION TELEVISION
42RV535U
46RV535U
52RV535U
For an overview of steps for setting up your new TV, see page 9.
Note: To display a High Definition picture, the TV must be receiving a
High Definition signal (such as an over-the-air High Definition TV
broadcast, a High Definition digital cable program, or a High Definition
digital satellite program). For details, please contact your TV antenna
installer, cable provider, or satellite provider.
© 2008 TOSHIBA CORPORATION
All Rights Reserved
Owner’s Record
The model number and serial number are on the back of
your TV. Record these numbers in the spaces below.
Refer to these numbers whenever you communicate
with your Toshiba dealer about this TV.
Model number:
Serial number:
YC/M VX1A00113200
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 2 Tuesday, July 22, 2008 5:25 PM
Dear Customer,
Thank you for purchasing this Toshiba LCD TV. This manual
will help you use the many exciting features of your new LCD
TV. Before operating your LCD TV, please read this manual
completely, and keep it nearby for future reference.
Safety Precautions
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN.
WARNING: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING
To prevent injury, this apparatus must be securely attached to
the floor/wall in accordance with the installation instructions.
See item 20 on page 3 and instructions on page 5.
WARNING: If you decide to wall mount this television,
always use a UL Listed wall bracket appropriate for the size
and weight of this television. The use of any wall bracket
other than a UL Listed wall bracket appropriate for the size
and weight of this television for wall mounting this television
could result in serious bodily injury and/or property damage.
See “Removing the Pedestal Stand” (- page 5).
NOTE TO CATV INSTALLERS
This is a reminder to call the CATV system installer’s attention
to Article 820-40 of the U.S. NEC, which provides guidelines for
proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical. For
additional antenna grounding information, see items 27 and 28
on page 4.
CHILD SAFETY:
It Makes A Difference How and Where You Use Your Flat
Panel Display
Congratulations on your purchase! As you enjoy your
new product, please keep these safety tips in mind:
The Issue
• The home theater entertainment experience is a growing trend
and larger flat panel displays are popular purchases. However,
flat panel displays are not always supported on the proper stands
or installed according to the manufacturer’s recommendations.
• Flat panel displays that are
inappropriately situated on dressers,
bookcases, shelves, desks,
speakers, chests or carts may fall
over and cause injury.
TOSHIBA Cares!
• The consumer electronics industry
is committed to making home
entertainment enjoyable and safe.
Tune Into Safety
• One size does NOT fit all. Follow the manufacturer’s recommendations
for the safe installation and use of your flat panel display.
• Carefully read and understand all enclosed instructions for
proper use of this product.
• Don’t allow children to climb on or play with furniture and
television sets.
• Don’t place flat panel displays on
furniture that can easily be used as
steps, such as a chest of drawers.
• Remember that children can
become excited while watching a
program, especially on a “larger
than life” flat panel display. Care
should be taken to place or install
the display where it cannot be
pushed, pulled over, or knocked down.
• Care should be taken to route all cords and
cables connected to the flat panel display so that they cannot be
pulled or grabbed by curious children.
Wall Mounting: If you decide to wall mount your
flat panel display, always:
• Use a mount that has been recommended by the display
manufacturer and/or listed by an independent laboratory (such
as UL, CSA, ETL).
• Follow all instructions supplied by the display and wall mount
manufacturers.
• If you have any doubts about your ability to safely install your
flat panel display, contact your retailer about professional
installation.
• Make sure that the wall where you are mounting the display is
appropriate. Some wall mounts are not designed to be mounted
to walls with steel studs or old cinder block construction. If you
are unsure, contact a professional
installer.
• A minimum of two people are
required for installation. Flat panel
displays can be heavy.
2
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 3 Tuesday, July 22, 2008 5:25 PM
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
15) CAUTION:
• To reduce the risk of electric shock, do not use the
polarized plug with an extension cord, receptacle, or
other outlet unless the blades can be inserted
completely to prevent blade exposure.
• To prevent electric shock, match wide blade of plug to
wide slot; fully insert.
5)
Do not use this apparatus near water.
6)
Clean only with dry cloth.
7)
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8)
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Installation, Care, and Service
9)
Do not defeat the safety purpose of Wide blade
the polarized or grounding type
plug. A polarized plug has two blades
with one wider than the other.
A grounding type plug has two blades
and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Follow these recommendations and precautions and heed all
warnings when installing your TV:
10) Protect the power cord from being walked
on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been
dropped.
Additional Safety Precautions
14a) CAUTION: If the TV is dropped and the cabinet or
enclosure surface has been damaged or the TV does not
operate normally, take the following precautions:
• ALWAYS turn off the TV and unplug the power cord to
avoid possible electric shock or fire.
• NEVER allow your body to come in contact with any
broken glass or liquid from the damaged television. The
LCD panel inside the TV contains glass and a toxic
liquid. If the liquid comes in contact with your mouth or
eyes, or your skin is cut by broken glass, rinse the
affected area thoroughly with water and consult your
doctor.
• ALWAYS contact a service technician to inspect the TV
any time it has been damaged or dropped.
16) WARNING:
To prevent the spread of fire, keep candles or other open
flames away from this product at all times.
Installation
17) Never modify this equipment. Changes or modifications
may void: a) the warranty, and b) the user’s authority to
operate this equipment under the rules of the Federal
Communications Commission.
18)
DANGER: RISK OF
SERIOUS PERSONAL
INJURY, DEATH, OR
EQUIPMENT DAMAGE!
Never place the TV on an unstable cart,
stand, or table. The TV may fall, causing
serious personal injury, death, or serious
damage to the TV.
19) To avoid damage to this product, never place or store the
TV in direct sunlight; hot, humid areas; or areas subject to
excessive dust or vibration.
20) Always place the TV on the floor or a sturdy, level, stable
surface that can support the weight of the unit. To secure the
TV, use a sturdy strap from the hooks on the rear of the TV
pedestal to a wall stud, pillar, or other immovable structure.
Make sure the strap is tight, secure, and parallel to the floor.
Sturdy strap (as short as possible)
4"
min.
Securement
Hooks
Clip
Securement
Clip
TV side
TV top
21) The apparatus shall not be exposed to dripping or
splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
22) Never block or cover the slots or openings in the TV
cabinet back, bottom, and sides. Never place the TV:
• on a bed, sofa, rug, or similar
surface;
• too close to drapes, curtains, or
walls; or
• in a confined space such as a
bookcase, built-in cabinet, or
any other place with poor
ventilation.
The slots and openings are provided to protect the TV from
overheating and to help maintain reliable operation of the
TV. Leave a space of at least 4 (four) inches around the TV.
(continued)
3
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 4 Tuesday, July 22, 2008 5:25 PM
23) Always place the back of the television at least four (4)
inches away from any vertical surface (such as a wall) to
allow proper ventilation.
24) Never allow anything to rest on or roll over the power cord,
and never place the TV where the power cord is subject to
wear or abuse.
25) Never overload wall outlets and extension cords.
26) Always operate this equipment from a 120 VAC, 60 Hz
power source only.
27) Always make sure the antenna system is properly
grounded to provide adequate protection against voltage
surges and built-up static charges (see Section 810 of the
National Electric Code).
Antenna lead-in wire
Ground clamp
Electric service equipment
Ground clamps
28)
Antenna discharge unit
(NEC Section 810-20)
31)
Never spill liquids or push objects of any kind into the TV
cabinet slots.
32) While it is thundering, do not touch the connecting cables
or apparatus.
33) For added protection of your TV from lightning and power
surges, always unplug the power cord and disconnect the
antenna from the TV if you leave the TV unattended or
unused for long periods of time.
34) During normal use, the TV may make occasional snapping
or popping sounds. This is normal, especially when the
unit is being turned on or off. If these sounds become
frequent or continuous, unplug the power cord and contact
a Toshiba Authorized Service Center.
35)
Grounding conductors
(NEC Section 810-21)
Power service grounding
electrode system (NEC Art 250 Part-H)
DANGER: RISK OF SERIOUS
PERSONAL INJURY OR DEATH!
• Use extreme care to make sure you are never in a
position where your body (or any item you are in contact
with, such as a ladder or screwdriver) can accidentally
touch overhead power lines. Never locate the antenna
near overhead power lines or other electrical circuits.
• Never attempt to install any of the following during
lightning activity: a) an antenna system; or b) cables,
wires, or any home theater component connected to an
antenna or phone system.
Care
For better performance and safer operation of your TOSHIBA
TV, follow these recommendations and precautions:
29) If you use the TV in a room whose temperature is 32 °F
(0 °C) or below, the picture brightness may vary until the
LCD warms up. This is not a sign of malfunction.
30) Always unplug the TV before
cleaning. Gently wipe the
display panel surface (the TV
screen) using a dry, soft cloth
only (cotton, flannel, etc.). A
hard cloth may damage the
surface of the panel. Avoid
contact with alcohol, thinner, benzene, acidic or alkaline
solvent cleaners, abrasive cleaners, or chemical cloths,
which may damage the surface. Never spray volatile
compounds such as insecticide on the cabinet. Such
products may damage or discolor the cabinet.
WARNING:
RISK OF ELECTRIC SHOCK!
WARNING: RISK OF
SERIOUS PERSONAL
INJURY OR EQUIPMENT
DAMAGE!
Never strike the screen with a sharp
or heavy object.
36) • The LCD screen of this product can be damaged by
ultraviolet radiation from the sun. When selecting a
location for the television, avoid locations where the
screen may be exposed to direct sunlight, such as in
front of a window.
• Never touch, press, or place anything on the LCD
screen. These actions will damage the LCD screen. If
you need to clean the LCD screen, follow the
instructions in item 30 on this page.
Service
37)
WARNING:
RISK OF ELECTRIC SHOCK!
Never attempt to service the TV yourself. Opening and
removing the covers may expose you to dangerous
voltage or other hazards. Failure to follow this WARNING
may result in death or serious injury. Refer all servicing not
specified in this manual to a Toshiba Authorized Service
Center.
38) If you have the TV serviced:
• Ask the service technician to use only replacement
parts specified by the manufacturer.
• Upon completion of service, ask the service technician
to perform routine safety checks to determine that the
TV is in safe operating condition.
39) The fluorescent lamp(s) in the LCD panel contain a small
amount of mercury.
When the TV reaches the end of its useful life, dispose of
the used TV by the approved method for your area, or ask
a qualified service technician to properly dispose of the
TV.
Note: The lamp(s) inside this product contain
mercury. Disposal may be regulated due to
environmental considerations. For disposal or
recycling information, contact your local authorities or the
Electronics Industries Alliance (www.eiae.org).
4
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 5 Tuesday, July 22, 2008 5:25 PM
Choosing a location for your LCD TV
To Display your LCD TV on the included Pedestal
Stand:
Observe the following safety precautions:
1) Read and Follow the pedestal assembly instructions
included with the pedestal.
CAUTION: Before beginning pedestal assembly,
carefully lay the front of the LCD Panel face down on a
flat, cushioned surface such as a quilt or blanket. Leave
the bottom of the unit protruding over the edge of the
surface and assemble the pedestal as indicated below.
Note: Extreme care should always be used when attaching
the pedestal stand to avoid damage to the LCD panel.
2) Place the TV on a sturdy, level surface that can support
the weight of the TV.
3) Be sure to secure the TV to a wall stud, pillar, surface, or
other immovable structure. To secure the TV in this
manner: (1) attach the provided securement clip to an
immovable structure, then (2) pass a sturdy strap
through the securement clip and attach each end to the
hooks located on the back of the TV. Be sure to leave at
least 4 inches between the TV and the wall or similar
structure for ventilation. See item 20, page 3 for
additional details.
To Display your LCD TV using a Wall Bracket:
If you decide to wall mount your LCD TV, always use a ULlisted wall bracket appropriate for the size and weight of the
LCD TV (- page 2) :
1) CAUTION: Two people are required for installation.
2) Unplug and remove any cables and/or other component
connectors from the rear of the TV.
3) Follow the instructions provided with your wall bracket.
Before proceeding, make sure the appropriate bracket(s)
are attached to the wall and the back of the TV as
described in the instructions provided with the wall
bracket.
4) After attaching the appropriate bracket(s) to the wall and
the back of the TV, remove the pedestal stand from the
TV as described below.
Removing the Pedestal Stand
1) Carefully lay the front of the unit face down on a flat,
cushioned surface such as a quilt or blanket. Leave the
stand protruding over the edge of the surface.
Note: Extreme care should always be used when removing
the pedestal stand to avoid damage to the LCD panel.
2) Remove the four screws shown in the diagram below.
This will allow removal of the pedestal stand.
3) Once you have removed all four screws holding the
pedestal stand in place, remove the pedestal stand from
the TV by sliding the pedestal stand away from the TV.
Four screws
5
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 6 Tuesday, July 22, 2008 5:25 PM
FCC Declaration of Conformity
Compliance Statement
(Part 15):
The Toshiba 42RV535U, 46RV535U and 52RV535U
Televisions comply with Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
The party responsible for compliance to these rules is:
Toshiba America Consumer Products, L.L.C.
82 Totowa Rd. Wayne, NJ 07470.
Ph: 1-800-631-3811
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
removing and applying power to the equipment, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
Caution: Changes or modifications to this equipment not
expressly approved by Toshiba could void the user’s authority
to operate this equipment.
ENERGY STAR® User Information
ENERGY STAR User Information Statement: the factory
default settings of this television meet ENERGY STAR®
requirements. Enabling or changing certain features and
functionality (e.g. Picture Settings, Auto Brightness Sensor,
Power-On Mode) may increase energy consumption,
possibly beyond the limits required for ENERGY STAR
qualification.
To ensure your television is operating at optimal energy
efficiency, select [Home] mode during initial activation. To
return to [Home] mode settings, select [AutoView] picture
mode, set the Auto Brightness Sensor to [On] mode, and set
the Power-On mode to [Power-Saving]. [AutoView] mode
is recommended for normal home use.
For more information, see page 35.
ENERGY STAR® qualified TV. Products that
earn the ENERGY STAR prevent green house
gas emissions by meeting strict guidelines set
by the U.S. Environmental Protection Agency.
ENERGY STAR and the ENERGY STAR mark
are registered U.S. marks.
Important notes about your LCD TV
The following symptoms are technical limitations of LCD
Display technology and are not an indication of
malfunction; therefore, Toshiba is not responsible for
perceived issues resulting from these symptoms.
1) An afterimage (ghost) may appear on the screen if a
fixed, non-moving image is displayed for a long period
of time. The afterimage is not permanent and will
disappear in a short period of time.
2) The LCD panel contained in this TV is manufactured
using an extremely high level of precision technology;
however, there may be an occasional pixel (dot of light)
that does not operate properly (does not light, remains
constantly lit, etc.). This is a structural property of LCD
technology, is not a sign of malfunction, and is not
covered under your warranty. Such pixels are not visible
when the picture is viewed from a normal viewing
distance.
Note: Interactive video games that involve shooting a “gun”
type of joystick at an on-screen target may not work with this
TV.
Trademark Information
• Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
6
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 7 Tuesday, July 22, 2008 5:25 PM
Contents
Important Safety Instructions .......................................... 3
Installation, Care, and Service ........................................ 3
Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Features of your new TV. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Overview of steps for installing, setting up, and
using your new TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
TV front and side panel controls and connections . . . . 10
TV back panel connections . . . . . . . . . . . . . . . . . . . . . . . . 11
Chapter 2: Connecting your TV . . . . . . . . . . . . . . . . . . . . . . .12
Overview of cable types . . . . . . . . . . . . . . . . . . . . . . . . . . 12
About the connection illustrations . . . . . . . . . . . . . . . . . 12
Connecting a VCR (or a VCR with S-video) and
antenna, Cable TV or Camcorder . . . . . . . . . . . . . . . 13
Connecting a DVD player with ColorStream®
(component video), a VCR, and a satellite
receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connecting a device to the IR OUT infrared terminal
using the IR blaster cable for IR pass-through
device control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Connecting an HDMI™ or DVI device to the HDMI
input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
REGZA LINK connection . . . . . . . . . . . . . . . . . . . . . . . . . 17
Connecting a digital audio system . . . . . . . . . . . . . . . . . 18
Connecting an audio system . . . . . . . . . . . . . . . . . . . . . . 18
Connecting a personal computer (PC) . . . . . . . . . . . . . . 19
Chapter 3: Using the remote control . . . . . . . . . . . . . . . . . . .20
Preparing the remote control for use . . . . . . . . . . . . . . . 20
Installing the remote control batteries . . . . . . . . . . . . . . 20
Learning about the remote control . . . . . . . . . . . . . . . . . 21
Using the remote control to control your other
devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Remote Control functional key chart . . . . . . . . . . . . . . . 23
Programming the remote control to control your
other devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Remote control codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Chapter 4: Menu layout and navigation . . . . . . . . . . . . . . . . .27
Main menu layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Setup/Installation menu layout . . . . . . . . . . . . . . . . . . . 27
Navigating the menu system . . . . . . . . . . . . . . . . . . . . . . 28
Chapter 5: Setting up your TV. . . . . . . . . . . . . . . . . . . . . . . .29
Setting the Demo Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Selecting the menu language . . . . . . . . . . . . . . . . . . . . . . 29
Configuring the antenna input source for the
ANT/CABLE terminal . . . . . . . . . . . . . . . . . . . . . . . . 30
Programming channels into the TV’s channel
memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Programming channels automatically . . . . . . . . . . . 30
Manually adding and deleting channels in the
channel memory . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Labeling channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Setting the HDMI™ audio mode . . . . . . . . . . . . . . . . . . . 33
Viewing the digital signal meter . . . . . . . . . . . . . . . . . . . 33
Setting the time zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Viewing the system status . . . . . . . . . . . . . . . . . . . . . . . . 34
Selecting the TOSHIBA Illumination mode . . . . . . . . . . 35
Selecting the Power-On Mode . . . . . . . . . . . . . . . . . . . . . 35
Selecting the Demo Mode . . . . . . . . . . . . . . . . . . . . . . . . . 35
Selecting the Energy Saving Mode . . . . . . . . . . . . . . . . . 35
Selecting ENERGY STAR® Qualified Mode . . . . . . . . . 35
Chapter 6: Using the TV’s features . . . . . . . . . . . . . . . . . . . . 36
Selecting the video input source to view . . . . . . . . . . . . 36
Labeling the video input sources. . . . . . . . . . . . . . . . . . . 36
Tuning channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Tuning channels using the Channel Browser™ . . . . 37
Setting the Channel Tuning Mode . . . . . . . . . . . . . . 39
Tuning to the next programmed channel . . . . . . . . 39
Tuning to a specific channel (programmed or
unprogrammed) . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Switching between two channels using Channel
Return. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Switching between two channels using
SurfLock™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Selecting the picture size. . . . . . . . . . . . . . . . . . . . . . . . . . 40
Scrolling the TheaterWide® picture (TheaterWide 2
and 3 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Using the auto aspect ratio feature . . . . . . . . . . . . . . . . . 42
Selecting the cinema mode
(480i and 1080i signals). . . . . . . . . . . . . . . . . . . . . . . . 43
Using the FREEZE feature . . . . . . . . . . . . . . . . . . . . . . . . 43
Adjusting the picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Selecting the picture mode. . . . . . . . . . . . . . . . . . . . . 43
Adjusting the picture quality. . . . . . . . . . . . . . . . . . . 43
Using the TheaterLock™ feature . . . . . . . . . . . . . . . . . . . 44
Using the closed caption mode . . . . . . . . . . . . . . . . . . . . 44
Base closed captions . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Digital CC Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
CC Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Adjusting the audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Muting the sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Using the digital audio selector . . . . . . . . . . . . . . . . 45
Selecting stereo/SAP broadcasts . . . . . . . . . . . . . . . 46
Adjusting the audio quality. . . . . . . . . . . . . . . . . . . . 46
Using the StableSound® feature . . . . . . . . . . . . . . . . 46
Selecting the optical audio output format . . . . . . . . 47
Using the Dolby® Digital Dynamic Range Control
feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Using the Locks menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Entering the PIN code . . . . . . . . . . . . . . . . . . . . . . . . 47
If you cannot remember your PIN code . . . . . . . . . 47
Changing your PIN code . . . . . . . . . . . . . . . . . . . . . . 48
Blocking TV programs and movies by rating
(V-Chip) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Downloading an additional rating system for
blocking TV programs and movies . . . . . . . . . . 48
Blocking channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Unlocking programs temporarily . . . . . . . . . . . . . . . 49
Using the input lock feature . . . . . . . . . . . . . . . . . . . 50
Using the GameTimer® . . . . . . . . . . . . . . . . . . . . . . . 50
Using the control panel lock feature. . . . . . . . . . . . . 50
Using the PC settings feature . . . . . . . . . . . . . . . . . . . . . . 51
Setting the PC Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Setting the sleep timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Using REGZA LINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
REGZA LINK playback device (DVD player, etc.)
control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
REGZA LINK input source selection . . . . . . . . . . . . 53
VOLUME and MUTE controls of Audio
Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Other REGZA LINK functions . . . . . . . . . . . . . . . . . 53
REGZA LINK PC Link . . . . . . . . . . . . . . . . . . . . . . . . 54
Using the HDMI settings feature. . . . . . . . . . . . . . . . . . . 54
Displaying TV status information . . . . . . . . . . . . . . . . . . 55
Understanding the auto power off feature . . . . . . . . . . 55
Understanding the last mode memory feature . . . . . . . 55
(continued)
7
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 8 Tuesday, July 22, 2008 5:25 PM
Chapter 7: Using the TV’s advanced features . . . . . . . . . . . . .56
Using the advanced picture settings features . . . . . . . . 56
Using SRT™ Super Upconversion™ . . . . . . . . . . . . . 56
Using dynamic contrast . . . . . . . . . . . . . . . . . . . . . . . 56
Using the static gamma feature. . . . . . . . . . . . . . . . . 56
Selecting the color temperature. . . . . . . . . . . . . . . . . 57
Using CableClear® digital noise reduction . . . . . . . 57
Using MPEG noise reduction . . . . . . . . . . . . . . . . . . 57
Using the Auto Brightness Sensor . . . . . . . . . . . . . . 58
Using the ColorMaster™ feature . . . . . . . . . . . . . . . . 58
Using the Game Mode feature . . . . . . . . . . . . . . . . . 59
Using the advanced audio settings features . . . . . . . . . 59
Using the surround sound features . . . . . . . . . . . . . 59
Chapter 8: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .60
General troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 60
LED indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Chapter 9: Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Acceptable signal formats for PC IN and HDMI
terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Limited United States Warranty
for LCD Televisions 26” and Larger . . . . . . . . . . . . . 65
Limited Canadian Warranty
for Toshiba Brand Flat Panel Televisions . . . . . . . . 66
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
8
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 9 Tuesday, July 22, 2008 5:25 PM
Chapter 1: Introduction
Features of your new TV
The following are just a few of the many exciting features
of your new Toshiba widescreen, integrated HD, LCD
TV:
• Integrated digital tuning (8VSB ATSC and QAM)
eliminates the need for a separate digital converter settop box (in most cases).
• 1080p output resolution.
• Four HDMI™ digital, high-definition multimedia
interfaces with 1080p input support (- page 16).
• HDMI capabilities
Lip-Sync Latency feature activates an auto audio/
video display timing adjustment function that allows
HDMI source devices to accurately perform
synchronization automatically.
Deep Color feature allows the HDMI source to
increase the available colors bits within the boundaries
defined by the RGB or YCbCr color space. (46” and 52”
models only)
• REGZA LINK allows control of external devices from
the TV remote via HDMI connection
(- page 52).
• Two sets of ColorStream® HD high-resolution
component video inputs (- page 14).
• Digital Audio Out optical audio connection with
Dolby® Digital optical output format (- page 47).
• CableClear® digital picture noise reduction
(- page 57).
• PC IN (Analog RGB) computer terminal (- page 19).
• IR OUT infrared terminal using the IR blaster cable for
IR pass-through device control (- pages 12 and 15).
• ColorMaster™ allows you to adjust the TV’s standard
colors. The menu for this feature has a unique “black”
design to enhance contrast while you’re adjusting the
color (- page 58).
• Channel Browser™ allows you to easily navigate
between all channels and inputs (- page 37).
• Channel Tuning Mode allows you to choose how
tuning will be handled for over-the-air analog and
digital channels (- page 39).
• GameTimer® allows you to set a time limit for input
source access (- page 50).
• SRT™ Super Upconversion™ allows you to modify SD
quality picture to HD quality level (- page 56).
• AutoView allows you to automatically adjust picture
settings based on ambient light conditions and input
signal content (- page 43).
•
Overview of steps for installing,
setting up, and using your new TV
Follow these steps to set up your TV and begin using its
many exciting features.
1
Observe the following when choosing a location for
the TV:
• Read “Important notes about your LCD TV”
(- page 6).
• Place the TV in a proper location (- pages 2–5)
2
Do not plug in any power cords until AFTER you
have connected all cables and devices to your TV.
3
BEFORE connecting cables or devices to the TV,
learn the functions of the TV’s connections and
controls
(- pages 10–11).
4
Connect your other electronic device(s) to the TV
(- pages 12–19).
5
See “Chapter 3: Using the remote control” (page 20) for an overview of the buttons on the
remote control, install the batteries and prepare to
operate your other device(s).
6
AFTER connecting all cables and devices, plug in the
power cords for your TV and other devices.
Note: After you turn on the TV, the Menu
Language, Energy Saving Mode, and Demo
Mode selection menus appear automatically by
default.
You can turn off the On-Screen demonstration
mode by setting the Demo Mode to Off.
(- page 29)
7
See “Menu layout and navigation” for a quick
overview of navigating the TV’s menu system (page 27).
8
Program channels into the TV’s channel memory
(- page 30).
9
For details on using the TV’s features, see Chapters
6 and 7.
10 For help, refer to the Troubleshooting Guide, see
Chapter 8.
11 For technical specifications and warranty
information, see Chapter 9.
ENERGY STAR® qualified
9
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 10 Tuesday, July 22, 2008 5:25 PM
Chapter 1: Introduction
TV front and side panel controls and connections
Model 42RV535U is used in this manual for illustration purposes.
Right side panel
TV front
6
10
7
11
8
12
9
5
13
14
1
2 3
4
Control panel
1
2
3
TOSHIBA Illumination
The TOSHIBA logo will be illuminated by the LED
backlight. See "Selecting the TOSHIBA Illumination
mode" on page 35 for additional information.
Auto Brightness Sensor
This sensor will detect the ambient light conditions
to optimize the backlighting levels. See "Using the
Auto Brightness Sensor" on page 58 for additional
information.
Remote sensor — Point the remote control toward
this remote sensor.
Effective range:
16.4 ft (5m)
4
5
6
Green and Yellow LEDs
Green = Power indicator
Yellow = Power-On Mode indicator (- “Selecting
the Power-On Mode” on page 35)
See “LED indications” on page 62 for additional
information.
VIDEO 2 IN — The side panel A/V connections are
referred to as “VIDEO 2” and include standard A/V
connections.
POWER — Press to turn the TV on and off.
If the TV stops responding to the controls on the
remote control or TV control panel and you cannot
7
8
9
turn off the TV, press and hold the POWER button
on the TV control panel for 5 or more seconds to
reset the TV.
ARROWS BbC c — When a menu is on-screen,
these buttons function as up/down/left/right menu
navigation buttons.
MENU (ENTER) — Press to access the menu system
(- page 27). When a menu is on-screen, the MENU
button on the TV’s control panel functions as the
ENTER button.
EXIT — Press to instantly close an on-screen menu.
10 CHANNEL Bb — When no menu is on-screen, these
buttons change the channel (programmed channels
only; - page 30).
11 VOLUME C c — These buttons adjust the volume
level.
12 INPUT — Repeatedly press to change the source you
are viewing (ANT/CABLE, VIDEO 1, VIDEO 2,
ColorStream HD1, ColorStream HD2, HDMI 1,
HDMI 2, HDMI 3, HDMI 4, PC).
13 HDMI™ IN — High-Definition Multimedia Interface
(HDMI 4) input receives digital audio and
uncompressed digital video from an HDMI device
or uncompressed digital video from a DVI device.
HDMI connection is necessary to receive 1080p
signals.
14 Service port — For service use only. Used for
updating the television’s firmware.
10
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 11 Tuesday, July 22, 2008 5:25 PM
Chapter 1: Introduction
TV back panel connections
For an explanation of cable types and connections, see pages 12–19.
TV back
1
2
3
4
Power cord
Cable Strap
5
6
7
1
DIGITAL AUDIO OUT — Optical audio output in
Dolby Digital or PCM (pulse-code modulation)
format for connecting an external Dolby Digital
decoder, amplifier, A/V receiver, or home theater
system with optical audio input.
2
HDMI™ IN — High-Definition Multimedia Interface
input receives digital audio and uncompressed
digital video from an HDMI device or
uncompressed digital video from a DVI device. Also
see item 4. HDMI connection is necessary to receive
1080p signals.
3
PC IN — For use when connecting a personal
computer.
4
PC/HDMI 1 (AUDIO) IN — PC audio input terminal
is shared with HDMI 1 analog audio input terminal,
and its use can be configured in the Audio Setup
menu (- page 51).
5
9
8
ColorStream® HD1 and ColorStream® HD2 — Two
sets of ColorStream® high-definition component
video inputs (with standard stereo audio inputs) for
connecting devices with component video output,
such as a Toshiba DVD player with ColorStream®.
Note: Component video cables carry only video
information; separate audio cables are required for a
complete connection.
6
10
VIDEO 1 IN — Standard (composite) video and
standard audio inputs plus optional S-video inputs
for connecting devices with composite video or Svideo output.
Note: Standard (composite) video and S-video cables
carry only video information; separate audio cables are
required for a complete connection.
7
Fixed Audio OUT — Analog audio outputs for
connecting an audio amplifier.
8
IR OUT — For controlling infrared remotecontrolled devices through the TV. You can connect
up to two devices with an optical IR blaster cable (page 12), and then control the devices using the TV’s
IR pass-through features.
9
Service port — For service use only. Used for
updating the television’s firmware.
10 ANT/CABLE — Input that supports analog (NTSC)
and digital (ATSC) off-air antenna signals and
analog and digital Cable TV (QAM) signals.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
11
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 12 Tuesday, July 22, 2008 5:25 PM
Chapter 2: Connecting your TV
Overview of cable types
Cables can be purchased from most stores that sell
audio/video devices. Before purchasing any cables, be
sure of connector types required by your devices and the
length of each cable.
Coaxial (F-type) cable
Coaxial (F-type) cable is used for connecting your
antenna, cable TV service, and/or cable converter box to
the ANT/CABLE input on your TV.
HDMI™ cable (with HDMI Logo “
”)
HDMI (High-Definition Multimedia Interface) cable is
for use with devices with an HDMI output. An HDMI
cable delivers digital audio and video in its native
format. This cable carries both video and audio
information; therefore, separate audio cables are not
required for a complete HDMI device connection (page 16, 17 and 19).
Note: An HDMI cable provides the best audio and picture
performance.
Dual-wand IR blaster cable
Standard A/V cables (red/white/yellow)
Standard A/V cables (composite video) usually come in
sets of three and are for use with video devices with
analog audio and composite video output. These cables
(and the related inputs on your TV) are typically colorcoded according to use: yellow for video, red for stereo
right audio, and white for stereo left (or mono) audio.
S-video cable
S-video cable is for use with video devices with S-video
output. Separate audio cables are required for a complete
connection.
Note: An S-video cable provides better picture performance
than a composite video cable. If you connect an S-video cable,
be sure to disconnect the standard (composite) video cable or
the picture performance will be unacceptable.
Component video cables (red/green/blue)
Component video cables come in sets of three and are for
use with video devices with component video output.
(ColorStream® is Toshiba’s brand of component video.)
These cables are typically color-coded red, green, and
blue. Separate audio cables are required for a complete
connection.
Note: Component video cables provide better picture
performance than a standard (composite) video or S-video
cable.
Dual-wand IR blaster cable is for use with video devices
with IR (infrared) remote control. This cable can be used
with the TV’s IR pass-through feature (- page 15).
To obtain IR blaster cable:
Visit http://ceaccessories.toshiba.com/
Optical audio cable
Optical audio cable is for connecting receivers with
Dolby Digital or PCM (pulse-code modulation) optical
audio input to the TV’s DIGITAL AUDIO OUT terminal
(- page 18).
Analog RGB (15-pin) computer cable
Analog RGB (15-pin) computer cable is for connecting a
PC to the TV’s PC IN terminal (- page 19).
Note: Separate audio cables are required for a complete
connection.
About the connection illustrations
You can connect different types and brands of devices to
your TV in several different configurations. The
connection illustrations in this manual are representative
of typical device connections only. The input/output
terminals on your devices may differ from those
illustrated herein. For details on connecting and using
your specific devices, refer to each device’s owner’s
manual.
12
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 13 Tuesday, July 22, 2008 5:25 PM
Chapter 2: Connecting your TV
Connecting a VCR (or a VCR with S-video) and antenna, Cable TV or
Camcorder
From Cable TV
or antenna
Camcorder
AUDIO
OUT
VIDEO
From Cable TV
Cable box
IN CH 3
CH 4
TV upper back panel
OUT
L
R
S-video cable
or
Standard
A/V cable
Stereo VCR
VIDEO
L
AUDIO
R
VIDEO 2 inputs
on TV right side panel
IN
CH 3
CH 4
OUT
L
R
IN
from
ANT
OUT
to
TV
Audio cable
TV lower back panel
You will need:
To view the antenna or Cable signal:
• coaxial cables
Select the ANT/CABLE video input source on the TV.*
• standard A/V cables
– For better picture performance, if your VCR has S-video,
use an S-video cable (plus the audio cables) instead of
the standard video cable.
– For better picture performance, if your camcorder has
S-video, connect an S-video cable (plus the audio cables)
to VIDEO 1 on the TV back instead of the VIDEO 2 on the
TV right side panel.
– If you have a mono VCR, connect L/MONO on the TV to
your VCR’s audio out terminal using the white audio cable
only.
• S-video cable (if your VCR or camcorder has S-video)
– Do not connect both types of video cable to VIDEO 1 at
the same time or the picture performance will be
unacceptable.
• standard audio cables (if your VCR or camcorder has
To view basic and premium Cable channels:
Turn OFF the VCR. Select the ANT/CABLE video input
source on the TV.* Tune the TV to channel 3 or 4
(whichever channel the Cable box output is set to). Use
the Cable box controls to change channels.
To view the VCR:
Turn ON the VCR. Select the VIDEO 1 video input
source on the TV.*
To view the camcorder video:
Select the VIDEO 2 video input source on the TV.*
* To select the video input source, press INPUT on the remote control
(- page 36). To program the TV remote control to operate other
devices, see Chapter 3.
S-video)
Note: When you use a Cable box, you may not be able to use
the remote control to program or access certain features on the
TV.
The unauthorized recording, use, distribution, or revision of
television programs, videotapes, DVDs, and other materials is
prohibited under the Copyright Laws of the United States and
other countries, and may subject you to civil and criminal
liability.
13
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 14 Tuesday, July 22, 2008 5:25 PM
Chapter 2: Connecting your TV
Connecting a DVD player with ColorStream® (component video), a VCR,
and a satellite receiver
Your TV has two sets of ColorStream® (component video) inputs.
TV upper back panel
Stereo VCR
AUDIO
OUT
Y
PB
L
PR
COMPONENT VIDEO S-VIDEO VIDEO
OUT
OUT
From antenna
VIDEO
L
AUDIO
R
IN
R
CH 3
CH 4
OUT
DVD player with component video
L
IN from ANT
OUT to TV
R
From satellite dish
AUDIO
OUT
Y
Satellite
IN
PB
PR
COMPONENT VIDEO S-VIDEO VIDEO
OUT
OUT
L
R
Satellite receiver with component video
TV lower back panel
You will need:
• coaxial cables
• standard A/V cables
– For better picture performance, if your VCR has S-video,
use an S-video cable (plus the audio cables) instead of
the standard video cable. Do not connect both types of
video cable to VIDEO 1 at the same time or the picture
performance will be unacceptable.
– If you have a mono VCR, connect L/MONO on the TV to
your VCR’s audio out terminal using the white audio cable
only.
To view satellite programs using the component
video connections:
Turn on the satellite receiver. Select the ColorStream
HD2 video input source on the TV.*
To view the VCR or view and record antenna
channels:
Turn ON the VCR. Tune the VCR to the channel you
want to watch. Select the VIDEO 1 video input source on
the TV.*
• standard audio cables
To record a TV program while watching a DVD:
• component video cables
– You can connect the component video cables (plus audio
cables) from the DVD player or satellite receiver to either
set of ColorStream terminals on the TV (HD1 or HD2). The
ColorStream HD1 and HD2 terminals can be used to
display Progressive (480p, 720p) and Interlaced (480i,
1080i). Please check the Owner’s Manual of the DVD
player or satellite in order to determine the best output
signal available (1080p is not supported).
– If your DVD player or satellite receiver does not have
component video, connect a standard A/V cable to
VIDEO 2 on the side panel. If your DVD player has HDMI
video, see page 16.
Turn ON the VCR. Tune the VCR to the channel to
record. Select the ColorStream HD1 video input source
on the TV* to view the DVD.
* To select the video input source, press INPUT on the remote control
(- page 36). To program the TV remote control to operate other
devices, see Chapter 3.
The unauthorized recording, use, distribution, or revision of
television programs, videotapes, DVDs, and other materials is
prohibited under the Copyright Laws of the United States and
other countries, and may subject you to civil and criminal
liability.
To view antenna or Cable channels:
Select the ANT/CABLE video input source on the TV.*
To view the DVD player:
Turn ON the DVD player. Select the ColorStream HD1
video input source on the TV.*
14
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 15 Tuesday, July 22, 2008 5:25 PM
Chapter 2: Connecting your TV
Connecting a device to the IR OUT
infrared terminal using the IR
blaster cable for IR pass-through
device control
You can use the TV’s IR OUT terminal (infrared passthrough) to remotely operate (through the TV) many
infrared remote-controlled devices (such as Toshiba
infrared remote-controlled VCRs or DVD players)
enclosed within an entertainment center or similar
cabinet. Without the IR OUT connection, the device
typically would need to be visible to operate it remotely.
You will need:
• dual-wand IR blaster cable (- page 12)
• other audio/video cables as required to connect the
device(s) to the TV (- pages 13–16)
To connect the IR blaster cable:
1
2
Locate the infrared sensor on the front of your
device. This sensor is marked on some devices.*
Align one of the IR blaster cable’s wands about 1
inch away from the infrared sensor on the front of
the device and attach it using double-sided
mounting tape. If you have a second device, attach
the second wand in a similar manner. (See
illustration.)
Note: If you do not have a second device, coil the second
wand with a rubber band and leave it behind the TV.
3
Plug the IR blaster cable’s plug into the TV’s IR OUT
terminal.
To control the device(s):
Point either the device’s remote control or the TV remote
control (that you previously programmed to operate the
device; - Chapter 3) toward the front of the TV and
press the button for the desired function. The signal
passes from the remote control through the TV to the
device via the IR blaster cable.
Front of IR-controlled DVD player (for example)
Front of IR-controlled audio device (for example)
Infrared
sensor
IR blaster cable wand
(approx.1 inch from device)
TV upper back panel
Note:
• If you use the device’s remote control to operate the device,
you also will need to use the TV’s remote control to operate
the TV.
• The IR pass-through feature does not support all
IR-controlled devices; satisfactory performance may not be
attainable with certain devices.
*If you cannot locate the device’s infrared
sensor:
1 Turn OFF the device.
2 Starting at the lower left corner of the device, place
the end of the device’s remote control (with the
infrared emitter) so it touches the front of the
device and press POWER. (Do not use the TV’s
remote control for this step.)
3 If the device turns on, the point at which the remote
control touched the device is the location of the
sensor.
4 If the device does not turn on, move the remote
control slightly to the right and press POWER
again.
5 Repeat step 4 until you locate the device’s infrared
sensor.
15
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 16 Tuesday, July 22, 2008 5:25 PM
Chapter 2: Connecting your TV
Connecting an HDMI™ or DVI device
to the HDMI input
The HDMI input on your TV receives digital audio and
uncompressed digital video from an HDMI source
device, or uncompressed digital video from a DVI
(Digital Visual Interface) source device.
This input is designed to accept HDCP (HighBandwidth Digital-Content Protection) program
material in digital form from EIA/CEA-861-D–
compliant[1] consumer electronic devices (such as a settop box or DVD player with HDMI or DVI output).
The HDMI input can accept and display VGA, SVGA,
XGA, WXGA, SXGA, 480i (60Hz), 480p (60Hz), 720p
(60Hz), 1080i (60Hz), and 1080p (24Hz/60Hz) signal
formats. For detailed signal specifications, see page 64.
Supported Audio format: Linear PCM, sampling rate
32/44.1/48 kHz
To connect a DVI device, you will need:
• one HDMI-to-DVI adapter cable (HDMI type A
connector)
– For proper operation, the length of an HDMI-to-DVI
adapter cable should not exceed 9.8 ft (3m). The
recommended length is 6.6 ft (2m).
• one 3.5mm Stereo to RCA Y-Cable
– An HDMI-to-DVI adapter cable transfers video only.
Separate analog audio cables are required (see
illustration).
– See “Setting the HDMI™ audio mode” (- page 33).
TV upper back panel
Note: To connect a PC to the HDMI input, see page 19.
To connect an HDMI device, you will need:
• one HDMI cable (type A connector) per HDMI device
– For proper operation, it is recommended that you use an
HDMI cable with the HDMI Logo (
).
– To display an 1080p/60Hz signal format, you will need a
High Speed HDMI cable. Conventional HDMI/DVI cable
may not work properly.
– HDMI cable transfers both video and audio. Separate
analog audio cables are not required (see illustration).
– See “Setting the HDMI™ audio mode” (- page 33).
TV upper back panel
TV right side panel
HDMI device
VIDEO
L
AUDIO
R
HDMI OUT
IN IN
OUT
L
R
To view the HDMI device video:
Select the HDMI 1, HDMI 2, HDMI 3, or HDMI 4 video
input source on the TV.*
DVI device
VIDEO
L
DVI/HDCP
OUT
AUDIO
R
IN IN
OUT
L
R
Note: To ensure that the HDMI or DVI device is reset properly,
it is recommended that you follow these procedures:
• When turning on your electronic components, turn on the
TV first and then the HDMI or DVI device.
• When turning off your electronic components, turn off the
HDMI or DVI device first and then the TV.
[1]EIA/CEA-861-D compliance covers the transmission of
uncompressed digital video with high-bandwidth digital content
protection, which is being standardized for reception of highdefinition video signals. Because this is an evolving technology, it
is possible that some devices may not operate properly with the TV.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
* To select the video input source, press INPUT on the remote control
(- page 36). To program the TV remote control to operate other
devices, see Chapter 3.
16
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 17 Tuesday, July 22, 2008 5:25 PM
Chapter 2: Connecting your TV
REGZA LINK connection
You can control the basic functions of connected audio/video devices using the TV’s remote control if you connect a
REGZA LINK compatible audio receiver or playback device. For an explanation of setup and operations, see pages 52
and 53.
TV upper back panel
Audio receiver
VIDEO
AUDIO
L
R
HDMI IN
HDMI OUT
TV right side panel
Playback device
(REGZA LINK DVD player,etc.)
VIDEO
L
AUDIO
R
IN
OUT
L
HDMI OUT
IN
OUT
R
L
R
Playback device
(REGZA LINK DVD player,etc.)
VIDEO
L
AUDIO
R
HDMI OUT
IN
OUT
L
R
To connect an Audio Receiver and Playback
Devices, you will need:
• HDMI cables (- page 16)
Note:
• If several devices are connected, REGZA LINK feature may
not operate properly.
• For proper operation, it is recommended that you use HDMI
cables with the HDMI Logo (
).
Before controlling the device(s):
• After completing the above connections, set the
REGZA LINK Setup menu as you desire (- page 53).
• The connected devices must also be set. For details, see
the operation manual for each device.
• The REGZA LINK feature uses the CEC technology as
regulated by the HDMI standard.
• This feature is limited to models incorporating
Toshiba’s REGZA LINK. However, Toshiba is not
liable for those operations. Refer to the individual
instruction manuals for compatibility information.
17
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 18 Tuesday, July 22, 2008 5:25 PM
Chapter 2: Connecting your TV
Connecting a digital audio system
The TV’s DIGITAL AUDIO OUT terminal outputs a
or 2-channel down-mixed PCM
Dolby®* Digital
(pulse-code modulation) signal for use with an external
Dolby® Digital decoder or other external audio system
with optical audio input.
You will need:
• optical audio cable (Use an optical audio cable that has
the larger “TosLink” connector and not the smaller
“mini-optical” connector.)
Note:
• Some audio systems may not be compatible with Dolby
Digital bitstream signals. Older audio systems that are not
compatible with standard optical out signals may not work
properly, creating a high noise level that may damage
speakers or headphones. THIS DAMAGE IS NOT COVERED
BY YOUR WARRANTY.
• The DIGITAL AUDIO OUT terminal may not output some
digital audio sources because of copy restrictions.
• The Dolby Digital format is only available when tuned to a
digital RF channel.
* Manufactured under license from Dolby Laboratories.
Dolby, and the double-D symbol are trademarks of Dolby
Laboratories.
Dolby Digital decoder or
other digital audio system
LINE IN
L
R
Connecting an audio system
Optical
Audio IN
This connection allows you to use external speakers with
an external analog audio amplifier to adjust the sound
level.
TV upper back panel
You will need:
• standard audio cables
Analog audio amplifier
To control the audio:
1
2
Turn on the TV and the digital audio device.
3
Highlight Audio Setup and press T.
LINE IN
L
R
Press Y on the TV’s remote control and open the
Audio menu.
TV upper back panel
Audio
Digital Audio Selector
Audio Settings
Advanced Audio Settings
Audio Setup
4
In the Optical Output Format field, select either
Dolby Digital or PCM, depending on your device
(- “Selecting the optical audio output format” on
page 47).
Audio Setup
PC Audio
No
HDMI 1 Audio
Auto
MTS
To control the audio:
1
2
Turn on the TV and the stereo amplifier.
Minimize the sound volume from the TV’s built-in
speakers and control the volume level using the
amplifier’s remote control.
Stereo
Language
English
Optical Output Format
Dolby Digital
Dolby Digital
Dynamic Range Control
Compressed
Reset
Done
18
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 19 Tuesday, July 22, 2008 5:25 PM
Chapter 2: Connecting your TV
Connecting a personal computer
(PC)
With either the PC IN or HDMI connection, you can
watch your computer’s display on the TV and hear the
sound from the TV’s speakers.
To connect a PC to the PC IN terminal on the TV:
When connecting a PC to the PC IN terminal on the TV,
use an analog RGB (15-pin) computer cable and a PC
audio cable.
• Signal names for mini D-sub 15-pin connector
Pin
No.
1
2
3
4
5
Signal
name
R
G
B
NC *
NC
Pin
No.
6
7
8
9
10
Signal
name
Ground
Ground
Ground
NC
Ground
Pin
No.
11
12
13
14
15
Signal
name
NC
NC
H-sync
V-sync
NC
*NC=Not connected
To connect a PC to the HDMI terminal on the TV:
When connecting a PC to the HDMI terminal on the TV,
use an adapter cable and analog audio cables.
If connecting a PC with an HDMI terminal, use an HDMI
cable (type A connector). Separate analog cables are not
necessary (- page 16).
TV upper back panel
TV upper back panel
PC audio
cable
Computer
PC audio
output
PC audio
cable
Computer
Conversion adapter
(if necessary)
PC audio
output
• To use a PC, set the monitor output resolution on the
PC before connecting it to the TV. The PC IN terminal
can accept and display VGA, SVGA, XGA, WXGA,
and SXGA signal formats. For detailed signal
specifications, see page 64.
• To display the optimum picture, use the PC setting
feature (- “Using the PC settings feature” on
page 51).
Note:
• The PC audio input terminals on the TV are shared with the
HDMI 1 analog audio input terminals (- page 51).
• Some PC models cannot be connected to this TV.
• An adapter is not needed for computers with a compatible
mini D-sub15-pin terminal.
• Depending on the DVD’s title and the specifications of the
PC on which you are playing the DVD-Video, some scenes
may be skipped or you may not be able to pause during
multi-angle scenes.
The HDMI input can accept and display VGA, SVGA,
XGA, WXGA, SXGA, 480i (60Hz), 480p (60Hz), 720p
(60Hz), 1080i (60Hz), and 1080p (24Hz/60Hz) signal
formats. For detailed signal specifications, see page 64.
Note:
• The edges of the images may be hidden.
• If receiving a 480i (HDMI), 480p (HDMI), 720p, 1080i, or
1080p signal program, Native mode scales the video to
display the entire picture within the borders of the screen
(i.e. no overscanning).
19
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 20 Tuesday, July 22, 2008 5:25 PM
Chapter 3: Using the remote control
Preparing the remote control
for use
Installing the remote control
batteries
Your TV remote control can operate your TV and many
other devices such as cable converter boxes, satellite
receivers, VCRs, DVD players, and HTIBs (home theater
in a box), even if they are different brands.
1
Squeeze tab
and lift cover.
If you have a Toshiba device:
Your TV remote control is preprogrammed to operate
most Toshiba devices (- page 24).
If you have a non-Toshiba device or a Toshiba
device that the remote control is not
preprogrammed to operate:
Remove the battery cover from the back of the
remote control.
2
Install two “AAA” size batteries, making sure to
match the + and – signs on the batteries to the signs
on the battery compartment.
3
Reinsert the battery cover in the remote control until
the tab snaps.
You can program the TV remote control so it will operate
the other device (- pages 22–26).
Caution: Batteries must not be exposed to excessive heat
such as sunshine, fire or the like.
Note:
• Be sure to use AAA size batteries.
• Dispose of batteries in a designated disposal area.
• Batteries should always be disposed of with the
environment in mind. Always dispose of batteries in
accordance with applicable laws and regulations.
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace batteries with
new ones.
• When necessary to replace batteries in the remote control,
always replace both batteries with new ones. Never mix
battery types or use new and used batteries in combination.
• Always remove batteries from the remote control if they are
dead or if the remote control is not to be used for an
extended period of time. This will prevent battery acid from
leaking into the battery compartment.
20
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 21 Tuesday, July 22, 2008 5:25 PM
Chapter 3: Using the remote control
Learning about the remote control
1
POWER turns the TV on and off. When the TV is on,
the green LED indicator on the TV front will be
illuminated.
The buttons used for operating the TV only are described
here. For a complete list of the remote control’s
functions, see the remote control functional key chart (page 23).
2
FREEZE freezes the picture.
Press again to restore the moving picture
(- page 43).
3
SLEEP accesses the sleep timer (- page 52).
4
PIC SIZE cycles through the picture sizes: Natural,
TheaterWide 1/2/3, Full, 4:3 HD, Native, and Dot
by Dot (- page 40).
5
Channel Numbers (0–9, –/100) directly tune
channels. The = button is used to enter two part
channel numbers (- page 39) or to edit the
Favorites List (- page 37).
6
INPUT selects the video input source (- page 36).
7
CH Bb cycles through programmed channels when
no menu is on-screen (- page 30).
8
VOL + – adjusts the volume level.
9
FAV BROWSER accesses the Favorites List in the
Channel Brower™ (- page 37).
10 RECALL displays TV status information
(- page 55).
11 CH RTN returns to the last viewed channel or source
(- page 40).
12 MUTE reduces or turns off the sound (- page 45).
13 INFO displays TV status information as well as
program details, when available (- page 55).
14 3 C / # c While watching TV, these buttons open
the Channel Browser™ and tune to the previous/
next channel in the channel history (- page 38).
(Also see “Arrow buttons.”)
15 Arrow buttons (BbC c) When a menu is on-screen,
these buttons select or adjust programming menus.
(Also see 3 C / # c.)
16 ENTER activates highlighted items in the main
menu system.
17 MENU accesses the main TV menu system
(- page 27).
18 EXIT closes on-screen menus.
19 MODE SELECT switch switches between TV,
CABLE/SAT, AUX 1, and AUX 2 modes
(- page 22). Set to “TV” to control the TV.
Note: The error message “Not Available” may appear if you
press a key for a function that is not available.
21
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 22 Tuesday, July 22, 2008 5:25 PM
Chapter 3: Using the remote control
Using the remote control to control
your other devices
If you have a non-Toshiba device or a Toshiba device
that the remote control is not preprogrammed to operate,
you must first program the remote control to recognize
the device (if you have not already done so)
(- pages 24–26).
1
POWER Turns the selected device on and off.
2
Channel Numbers (0-9) Press to directly access
channels (as opposed to < ,).
3
+10 Press to directly access DVD chapters higher
than 10.
4
TOP MENU Accesses a DVD’s top menu.
5
CH Bb For channels programmed into the channel
memory (- page 39):
B selects the next higher channel.
b selects the next lower channel.
6
GUIDE Displays the channel guide in the CABLE/
SAT mode.
SET UP Accesses a DVD’s setup menu in the AUX
mode.
7
INFO Displays TV status information on-screen.
8
BbC c Press to navigate DVD menus (may not work
on some DVD players).
9
ENTER Required by some satellite receivers and
DVD players to activate certain functions.
To use your TV remote control to operate a:
• Cable converter box or satellite receiver, set the MODE
SELECT switch to CABLE/SAT.
• VCR, set the MODE SELECT switch to AUX 1.
• DVD player or HTIB, set the MODE SELECT switch
to AUX 2.
Note: Even after the TV remote control is programmed, it may
not operate certain features on any other devices. If this
happens and you wish to use those features, you will need to
use the device’s original remote control.
Point the remote control
directly at the device.
10 DVD CLEAR Press to reset the title and chapter
number.
11 PLAY Begins playback of a tape or DVD.
12 PAUSE Press during play or record mode to pause
the picture; press again to restart.
13 STOP Stops the tape or DVD.
14 SKIP z Skips forward to locate later DVD chapters.
15 FF Fast-forwards the tape or DVD. (Press during
play mode to view the picture moving rapidly
forward.)
16 SKIP Z Skips back to beginning of current DVD
chapter, or locates previous chapters.
17 REW Rewinds/reverses the tape or DVD. (Press
during play mode to view the picture moving
rapidly backward.)
16
17
18
19
18 TV/VCR To view one program while recording
another, press to select TV mode.
SEARCH selects a specific DVD chapter, title or
time.
19 REC Starts tape recording.
20 MODE SELECT switch Set to “TV” to control the
TV; “CABLE/SAT” to control a cable converter box
or satellite receiver; “AUX 1” to control a VCR;
“AUX 2” to control a DVD player or HTIB.
22
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 23 Tuesday, July 22, 2008 5:25 PM
Chapter 3: Using the remote control
Remote Control functional key chart
Note:
• “---” = key does not send a signal in that remote control mode.
• “sTV” = key will affect the TV, even though the remote control is in another mode.
• * Not available for your TV.
REMOTE CONTROL KEY
POWER
SLEEP
PIC SIZE
FREEZE
1-9
0
100/–/+10
INPUT
FAV BROWSER/
TOP MENU
MUTE
SET UP/GUIDE
VOL + –
CHBb
RECALL
CH RTN/DVD RTN
INFO
ENTER
Toshiba TV
Power
Sleep timer
Picture size
FREEZE
Digit 1-9
Digit 0
– (sub CH)
TV/Video select
FAV BROWSER
DVD TOP Menu*
Sound mute
Guide*
Volume up/down
Channel
up/down
RECALL
Previous channel
DVD previous menu*
Info
Enter
CABLE
Power
s TV
s TV
s TV
Digit 1-9
Digit 0
--s TV
SAT (satellite)
Power
s TV
s TV
s TV
Digit 1-9
Digit 0
– (sub CH)
s TV
AUX 1 (VCR)
Power
s TV
s TV
s TV
Digit 1-9
Digit 0
100
s TV
AUX 2 (DVD or HTIB)
Power
s TV
s TV
s TV
Digit 1-9
Digit 0
+10
s TV
---
---
---
Top Menu
s TV
--s TV
Channel
up/down
s TV
s TV
SAT Guide
s TV
Channel
up/down
s TV
s TV
--s TV
Channel
up/down
s TV
s TV
Setup
s TV
Channel
up/down
s TV
---
---
---
DVD Return
-----
Info
Select, Enter
Menu
up/down
-----
Display
Enter
---
Menu up/down
Bb
Menu up/down
---
C3
Menu left/
Channel Browser™
Menu right/
Channel Browser™
Menu
Exit
DVD clear*
Pause*
Play*
Stop*
Skip REV*
Skip FWD*
Rewind*
Fast FWD*
---
Menu left
---
Menu left
---
Menu right
---
Menu right
---
Action Menu
---
DVD Menu
---
Exit
---
DVD Clear
---------------
---------------
Pause
Play
Stop
----Rewind
Fast FWD
Pause
Play
Stop
Skip REV
Skip FWD
Rewind
Fast FWD
DVD search*
---
---
TV/VCR
DVD search
Record (2
click)
-------------
Record (2 click)
c#
MENU
EXIT/DVD CLEAR
PAUSE/STEP
PLAY
STOP
SKIP Z
SKIP z
REW
FF
TV/VCR/
SEARCH
REC
REC MENU*
---
---
RESUME PLAY
SLOW +
ANGLE
SUB TITLE
AUDIO
EJECT
--SLOW FWD*
Angle*
Sub title*
Audio*
Eject*
-------------
-------------
Resume Play
SLOW FWD
DVD Angle
DVD Sub title
DVD Audio
DVD Eject
23
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 24 Tuesday, July 22, 2008 5:25 PM
Chapter 3: Using the remote control
Programming the remote control
to control your other devices
• Some newer VCRs respond to either of two codes. These
VCRs have a switch labeled “VCR1/VCR2.” If your VCR has
this kind of switch and does not respond to the codes for
your VCR brand, set the switch to the other position (“VCR1”
or “VCR2”) and reprogram the remote control.
Your Toshiba TV remote control is preprogrammed to
operate most Toshiba devices. To program your TV
remote control to operate a non-Toshiba device (or a
Toshiba device that it is not preprogrammed to operate),
follow the steps below. For details on using the remote
control to operate the device, see page 22.
1
In the remote control code table (- page 25), find
the code for your device. If more than one code is
listed, try each one separately until you find one that
works.
2
Set the MODE SELECT switch to the type of device
you are programming the remote control to operate
— CABLE/SAT (for a cable converter box or satellite
receiver), AUX 1 (for a VCR or TV/VCR combo), or
AUX 2 (for a DVD player or HTIB [home theater in a
box]).
3
While holding down E, press the Channel
Number buttons to enter the 3-digit code for your
device.
4
To test the code, turn on the device, point the remote
control at it, and press p. See notes below.
• If the correct code was entered, the device will
turn off.
• If the device does not respond, repeat steps 1–4
using another code.
• If the device does not respond to another code,
you will need to use the remote control that came
with the device.
5
Remember to set the MODE SELECT switch back to
“TV” to control the TV.
6
For future reference, write down the code(s) you
used:
DEVICE
CODE
DEVICE
CODE
Note:
• In addition to POWER, confirm that all necessary keys on the
TV remote control operate your device. If some keys are not
operational, repeat the device code setup using another
code (if other codes are listed for your device). If, after trying
all listed codes, the necessary keys do not operate your
device, use the device’s original remote control.
• Every time you change the batteries, you will need to
reprogram the remote control.
24
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 25 Tuesday, July 22, 2008 5:25 PM
Chapter 3: Using the remote control
Remote control codes
In some cases you may not be able
to operate your device with the TV
remote control. Your device may
use a code that is not recognized by
the TV remote control. If this
happens, use the device’s remote
control.
Cable converter box
ABC
Archer
Cableview
Century
Citizen
Contec
Diamond
GE
Gemini
Hamlin
Hitachi
Jasco
Motorola/GI/Jerrold
Magnavox
Memorex
Multi Canal
Novavision
Panasonic
Philco
Philips
Pioneer
Proscan
Radio Shack
RCA
Realistic
Recoton
Samsung
Scientific Atlanta
Sears
Signature
Signature 2000
Sprucer
Starcom
Stargate
Sylvania
TeleView
Texscan
Tocom
U. S. Electronics
United Cable
Universal
Wards
061, 062, 063, 082,
084, 087, 092,
096, 098
065, 092, 097, 099
064, 094
092
090, 092, 097
083, 085, 086, 088,
093, 098
093
061, 062
069, 070, 094
093
062, 095, 096
097
062, 069, 071, 082,
086, 089, 096, 107
072, 096
092, 104
090
101
081, 083, 085
087
066, 067, 068, 070,
072, 073, 074, 075,
092
076, 077
061, 062
092, 097, 099
064, 081
065
102
077, 090
063, 078, 079, 080,
088, 098, 101, 105
095
062
096
081, 085
069, 082, 087, 096,
103, 104
069, 090
095, 100
090
100
071, 084, 085
087, 096, 098
082
065, 092, 097, 099,
102, 103
096
Drake
Echostar
Express Vu
Fujitsu
GE
General Instruments
Hitachi
Hughes
Hughes Network
Systems
Intersat
Janeil
JVC
Kenwood
Magnavox
Optimus
Pansat
Primestar
Proscan
Radio Shack
RCA
Realistic
Samsung
Sony
Star Choice
Star Trak
STS
Toshiba
Uniden
Zenith
020, 040, 044, 046,
050, 053
018, 041, 051
057
027
008, 009, 013
010, 011, 012, 022,
023, 031, 049
033
033
019
048
027
017, 057
029
060
058
036, 052
015, 042
008, 009, 013
022, 023, 030
008, 009, 013, 016
030
059
014, 055
057, 106
025, 026, 037, 054
024
000, 001, 002, 003,
004, 005, 006, 007,
020, 031, 056
021, 028, 030, 032,
035, 039, 043, 045,
047, 058
027
TV/VCR Combo
Action
GE
Goldstar
Panasonic
Precision
Quasar
Realistic
Sony
Toshiba
Zenith
Totevision
078
059, 062
065
065
078
065
079
074
057
065
009, 010, 065
DVD/VCR Combo
Go Video
JVC
RCA
Samsung
Sanyo
Zenith
DVD=087,
VCR=081
DVD=088,
VCR=082
DVD=089,
VCR=083
DVD=090,
VCR=084
DVD=091,
VCR=085
DVD=092,
VCR=086
DVD player
Satellite receiver
Alphastar
Chaparral
DISH Network
038, 059
034
057
Aiwa
Apex
BOSE
Broksonic
006, 015
016, 017
097
018
Clarion
Classic
Daewoo
Denon
Emerson
Fisher
Funai
GE
Go Video
GPX
Hitachi
JVC
Kenwood
Konka
Magnavox
Memorex
Mintek
NAD
Nakamichi
Norcent
Onkyo
Oritron
Panasonic
Philips
Pioneer
Proscan
Qwestar
RCA
Sampo
Samsung
Sansui
Sanyo
Sharp
Sherwood
Sony
Sylvania
Teac
Technics
Techwood
Toshiba
Yamaha
Zenith
019
020
021
022, 023, 024, 025
026, 027
028
027
001, 029, 030
087
031
005, 032, 033, 034,
035
003, 007, 036, 042,
088
037
008, 009
004, 038
039
040
026
041
043
044
058
010, 045, 046, 047,
048, 049, 050
004, 051
052, 053, 054, 055
001, 056
057, 058
001, 002, 059, 089
060
061, 062, 086, 090
073
063, 091
064, 067
074
011, 012, 065, 066,
068, 069, 070
027
071
072
075
000, 013, 076, 077,
078
079, 080, 081
014, 082, 092
Portable DVD player
Aiwa
Audiovox
Panasonic
RCA
093
094, 095
024, 096, 099
098
VCR
Admiral
Aiko
Aiwa
Akai
Audiovox
Bell & Howell
Broksonic
Calix
Carver
CCE
Citizen
Colortyme
049
019
018
003, 004, 037, 038,
039, 058, 069
010
007, 068
008, 017
010
026
019
009, 010, 011, 012,
013, 014, 015, 019,
057, 073
005
(continued)
25
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 26 Tuesday, July 22, 2008 5:25 PM
Chapter 3: Using the remote control
Craig
Curtis Mathes
Daewoo
Daytron
Denon
Dimensia
Electrohome
Emerson
Fisher
Fuji
Funai
Garrard
GE
Go Video
Goldstar
Gradiente
Harman Kardon
Hitachi
JBL
JC Penney
Jensen
JVC
Kenwood
Kodak
LG
Lloyds
Logik
LXI
Magnasonic
Magnavox
Marantz
Memorex
MGA
MGN
Minolta
Mitsubishi
Montgomery Ward
Motorola
MTC
Multitech
NEC
Nikko
Noblex
Optimus
Optonica
009, 010, 016, 061,
065, 079
001, 005, 009, 012,
014, 040, 048, 053,
056, 057
011, 013, 015, 017,
018, 019, 057, 078
078
063
001, 048
010, 020, 065
003, 008, 010, 011,
017, 018, 020, 028,
039, 054, 057, 062,
065, 068, 072
007, 016, 021, 022,
023, 057, 064, 068,
070, 071, 079
004, 041
018, 073
018
001, 002, 009, 040,
042, 048, 056
056, 059, 061, 081
005, 010, 014, 054,
056, 065, 067
018, 065
005
024, 025, 035, 037,
042, 063, 070, 080
076
005, 006, 007, 008,
009, 010, 023, 024,
025, 026, 035, 056,
061, 063, 065
024, 025, 037, 050
005, 006, 007, 014,
037, 043, 055, 062,
063, 068, 082
005, 006, 007, 012,
014, 037, 043, 050,
053, 068, 071
010
010
053, 073, 079
061
010
061, 065, 078
026, 027, 034, 044,
057, 061, 072
005, 006, 007, 012,
014, 026, 053, 067
007, 009, 010, 016,
018, 034, 049, 063,
065, 066, 068, 075,
079
020, 028, 039
056
024, 025, 035, 063
020, 024, 025, 028,
039, 043, 065
049
049
009, 046, 061
009, 012, 018
005, 006, 007, 012,
014, 037, 043, 053,
054, 067, 070
010
009
010, 049, 065
031
Orion
Panasonic
Pentax
Pentex Research
Philco
Philips
Pioneer
Portland
Proscan
Proton
Quasar
Radio Shack
Radio Shack/Realistic
Radix
RCA
Realistic
Ricoh
Runco
Samsung
Sansui
Sanyo
Scott
Sears
Sharp
Shintom
Signature
Signature 2000
Singer
Sony
STS
Sylvania
Symphonic
Tandy
Tashiko
Tatung
Teac
Technics
Teknika
Toshiba
Totevision
Unitec
Unitech
Vector Research
054, 057, 062, 065,
068, 072
036, 045, 046, 057,
061, 072, 079
012, 024, 025, 035,
042, 053, 063
014
026, 027, 063
026, 031, 044, 057
006, 024, 043, 055
012, 013, 015
001, 002, 048
061
045
010, 031, 065
007, 009, 010, 016,
018, 020, 021, 022,
031, 049
010
001, 002, 003, 009,
024, 025, 029, 035,
040, 042, 045, 048,
055, 056, 063, 071,
083
007, 009, 010, 011,
016, 018, 020, 021,
022, 031, 049, 051,
056, 060, 065, 075,
079
047
034
009, 011, 038, 056,
073, 084
006, 037, 043, 061
007, 009, 016, 054,
064, 068, 071, 075,
079, 085
008, 011, 017, 028,
030, 057, 065, 072
007, 010, 016, 021,
022, 023, 024, 025,
035, 053, 057, 063,
064, 065, 068, 071,
075, 079
013, 020, 031, 049,
051, 060, 066
004, 025, 032, 061
049
075
047, 061
004, 032, 033, 041,
052, 058, 070, 074,
076, 077, 080
035
018, 026, 027, 028,
044, 072
018, 050, 051, 053,
073, 079
007
010
037
018, 029, 037
036
010, 018, 065
000, 011, 021, 023,
024, 028, 030, 039,
057, 074, 078, 079,
100, 101
009, 010, 065
073
009
005, 006, 011, 012,
053
Video Concepts
Wards
White Westinghouse
XR-1000
Yamaha
Zenith
005, 006, 011, 012,
039, 053
009, 010, 011, 016,
018, 020, 024, 025,
031, 035, 049, 051,
056, 057, 060, 065,
066, 079
073
018
005, 006, 007, 014,
037, 053
004, 032, 034, 041,
047, 069, 086
HTIB
Lasonic
Panasonic
Venturer
083
084
085
26
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 27 Tuesday, July 22, 2008 5:25 PM
Chapter 4: Menu layout and navigation
Main menu layout
Setup/Installation menu layout
To open the main menus (illustrated below), press Y on
the remote control or TV control panel.
To open the Installation menu (illustrated below), press
Y on the remote control or TV control panel, open the
Setup menu, select Installation, and press T.
Icon
Applications
Video
Audio
Preferences
Locks
Setup
Item
Channel Browser™
Favorites Browser
REGZA LINK Player Control
Start Demo
Mode
Picture Settings
Noise Reduction
Auto Brightness Sensor
ColorMaster
Game Mode
Theater Settings
TheaterLock
Digital Audio Selector
Audio Settings
Advanced Audio Settings
Audio Setup
CC Selector
Base CC Mode
Digital CC Settings
Input Labeling
Channel Labeling
Menu Language
Channel Browser Setup
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Control Panel Lock
GameTimer®
New PIN Code
Installation
REGZA LINK Setup
Sleep Timer
HDMI Settings
PC Settings
TOSHIBA Illumination
Power-On Mode
Demo Mode
Energy Saving Mode
Page
37
37
52
29
43
43
57
58
58
59
40
44
45
46
59
46
45
44
44
36
32
29
38
48
48
49
50
50
50
48
30
53
52
54
51
35
35
35
35
Icon
Terrestrial
Item
Input Configuration
Channel Program
Channel Add/Delete
Channel Tuning Mode
Signal Meter
Page
30
30
31
39
33
Time Zone Setup
34
System Information
34
Time Zone
System Status
27
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 28 Tuesday, July 22, 2008 5:25 PM
Chapter 4: Menu layout and navigation
Navigating the menu system
You can use the buttons on the remote control or TV
control panel to access and navigate your TV’s on-screen
menu system.
• Press Y to open the menu system.
Applications
Channel Browser
Favorites Browser
REGZA LINK Player Control
Start Demo
Navigate
ENTER Select
CH RTN Back
EXIT Exit
• When a menu is open, use the up/down/left/right
arrow buttons (BbC c) on the remote control or TV
control panel to move in the corresponding direction
in the menu.
• Press T to save your menu settings or to select a
highlighted item. (A highlighted menu item appears
in a different color in the menu.)
• All menus close automatically if you do not make a
selection within 60 seconds, except the signal meter
menu, which closes automatically after about 5
minutes.
• To close a menu instantly, press O.
Note:
• The menu background may sometimes appear black,
depending on the signal the TV is receiving. This is not a
sign of malfunction.
• The Video sub-menu appears with a black background,
which looks different from other menus.
For some video setting items, you can directly enter
values using the number keys on the remote control. To
enter a negative number, use =. To save a new setting,
press T. To cancel an entry, either allow the window to
time out or move to another item; the previous setting
will be restored.
28
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 29 Tuesday, July 22, 2008 5:25 PM
Chapter 5: Setting up your TV
Setting the Demo Mode
Selecting the menu language
When you first turn on the TV, the Menu Language,
Energy Saving Mode, and Demo Mode selection
windows will appear by default.
You can choose from three different languages (English,
French and Spanish) for the on-screen display of menus
and messages.
To select settings:
To select the menu language:
1
1
2
3
From the Menu Language selection window,
highlight your preferred language and press T.
Initial Setup
Menu Language
Please select a language.
English
Español
Press Y and open the Preferences menu.
Highlight Menu Language and press c.
Press B or b to select your preferred menu language
and press T.
Preferences
Français
CC Selector
2
Base CC Mode
Next, the Energy Saving Mode setting window will
appear.
For normal home use, press c to select Home and
press T.
Initial Setup
Input Labeling
Channel Labeling
Menu Language
Channel Browser Setup
English
English
Français
Español
Energy Saving Mode
To use this TV for displaying in a retail showroom,
please select [Retail].
Off
Digital CC Settings
4
Press O to close the Preferences menu.
[Home] mode is recommended for normal home
use. (ENERGY STAR® qualified)
Retail
3
Home
Next, the Demo Mode setting window will appear.
Initial Setup
Demo Mode
To use the demo, please select [Store (On)]. For
normal TV usage, please select [Normal (Off)].
Normal (Off)
Store (On)
For normal TV usage, select Normal (Off).
To enable the on-screen demonstration, select Store
(On). The SRT Super Upconversion demonstration
window will display. To restart the on-screen
demonstration, press Y on the remote or on the TV
for 2 seconds.
Note: The on-screen demonstration will automatically
restart after 120 seconds of inactivity.
To change the Demo Mode setting:
Press the MENU and VOLUMEC buttons on the TV
control panel at the same time and hold for about 2
seconds, or use the Demo Mode item in the Setup menu
(- page 35).
29
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 30 Tuesday, July 22, 2008 5:25 PM
Chapter 5: Setting up your TV
Configuring the antenna input
source for the ANT/CABLE terminal
When you press < or , on the remote control or TV
control panel, your TV will stop only on the channels
you programmed into the TV’s channel memory.
Follow the steps below to program channels into the
TV’s channel memory.
To configure the ANT/CABLE input:
1
2
Programming channels into the
TV’s channel memory
Press Y and open the Setup menu.
Highlight Installation and press T.
Programming channels automatically
Setup
Your TV can automatically detect all active channels in
your area and store them in its memory. After the
channels are programmed automatically, you can
manually add or erase individual channels in the
channel memory.
Installation
REGZA LINK Setup
Sleep Timer
HDMI Settings
PC Settings
TOSHIBA Illumination
Power-On Mode
Demo Mode
Energy Saving Mode
3
On
Power-Saving
Off
Home
(A new set of Installation menu icons will appear, as
shown below.) Open the Terrestrial menu, highlight
Input Configuration, and press T.
Installation
Terrestrial
Input Configuration
Channel Program
Channel Add/Delete
Channel Tuning Mode
Signal Meter
4
Auto
Press C or c to select the input source (Cable or
Antenna) for the ANT/CABLE input on the TV.
Input Configuration
ANT/CABLE In
Cancel
5
Note:
• You must configure the ANT/CABLE input source before
programming channels (- left-hand column).
• If the ANT/CABLE input signal type is set to Cable, the
automatic channel programming process erases channels
that were previously programmed into the TV’s memory.
• If the ANT/CABLE input signal type is set to Antenna, the
automatic channel programming process adds newly found
channels to the existing set of programmed channels (and
does NOT erase channels that were previously
programmed into the TV’s memory.) To remove an Antenna
source channel from the memory, you must manually delete
it.
• To tune the TV to a channel not programmed in the channel
memory, you must use the Channel Number buttons on the
remote control.
• Programming channels when the ANT/CABLE input is
configured for Cable will take substantially longer than when
the antenna input is configured for Antenna. This is normal;
however, once channel programming is finished, you should
not have to repeat the programming process again unless
your Cable TV service lineup changes significantly.
Cable
Done
To save your new settings, highlight Done and press
T. To revert to your original settings, highlight
Cancel and press T.
To program channels automatically:
1
Configure the ANT/CABLE input, if you have not
already done so (- left-hand column).
2
From the Setup menu, highlight Installation and
press T. A new set of Installation menu icons will
appear.
30
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 31 Tuesday, July 22, 2008 5:25 PM
Chapter 5: Setting up your TV
3
Open the Terrestrial menu, highlight Channel
Program to bring up Start, and press T again to
begin channel programming.
To revert to your original settings:
Highlight Cancel and press T before saving.
ANT/CABLE
Cable
Scanning channels, please wait ...
5%
Number of Channels Found - 52
Scanning Analog Channels
Found Channel - 55
Cancel
The TV will automatically cycle through all the
channels, and store all active channels in the channel
memory. While the TV is cycling through the
channels, the message “Scanning channels, please
wait” appears (as shown above).
4
Note: A video preview of the currently highlighted channel is
provided to assist you in adding/deleting channels.
To cancel channel programming, press O on the
remote control (or highlight Cancel in the on-screen
display and press T).
When channel programming is finished, press
< or , to view the programmed channels.
Manually adding and deleting channels
in the channel memory
To remove all channels from the channel memory:
Highlight Reset and press T, and then highlight Done
and press T.
To remove encrypted channels from the channel
memory:
If an encrypted channel is accidentally added to the
channel list by programming channels, you can remove
the unwanted encrypted (non-viewable) channel while
you are channel surfing. When you tune into an
encrypted channel, the following message will appear.
Digital Channel Is Encrypted - Press 1 on remote to remove channel
Press 1 while the message is on the screen to remove
the unnecessary channel from the channel list.
After automatically programming channels into the
channel memory, you can manually add or delete
individual channels.
To add or delete channels in the channel memory:
1
From the Setup menu, highlight Installation and
press T. A new set of Installation menu icons will
appear.
2
Open the Terrestrial menu, highlight Channel Add/
Delete, and then press T.
To add a channel to the channel memory:
Highlight the unchecked box next to the channel number
you want to add, and then press T to check the box.
To manually add digital subchannels on a
physical channel:
Use the Channel Numbers and the Dash (=) on the
remote control to enter the channel number (for
example, 56–1).
If the channel is found, the number will be added to the
list and the box will be checked.
If the channel is not found, a message will appear.
To remove a channel from the channel memory:
Highlight the checked box next to the channel number
you want to remove, and then press T to uncheck the
box.
To save your new settings:
Highlight Done and press T.
31
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 32 Tuesday, July 22, 2008 5:25 PM
Chapter 5: Setting up your TV
Labeling channels
A list of common channel labels (logos) for various
channels (ABC, CBS, etc.) will be programmed into the
TV. You will be able to view and assign these logos from
the Channel Labeling window. If the desired channel
label is not provided in the list, you will be able to
manually enter/edit labels using the software keyboard.
To create and assign a custom label:
1
2
3
To assign channel labels:
1
From the Preferences menu, highlight Channel
Labeling and press T.
The Channel Labeling window opens.
2
3
Press < or , to select the channel you want to label.
4
5
Repeat steps 2 and 3 for other channels.
Press BbC c to highlight the desired channel label
and press T.
To save your settings, highlight Done and press T.
The maximum number of labels that can be stored is
128.
Open the Channel Labeling window.
3
4
5
Press BbC c to highlight No Label and press T.
Press < or , to select the channel for which you
want to remove the label.
Repeat steps 2 and 3 for other channels.
To save your settings, highlight Done and press T.
Press < or , to select a channel you want to label.
Press Bb c to highlight Custom and press T.
The software keyboard will appear.
1 1
A BCHCRTN
a Cancel
b c 2
2Edit
4 GH I g h i 4
5 J K L j k l 5
7 PQR S p q r s 7
8 T U V t u v 8
_
100 Backspace
0 0
Send
Exit
E F d
e f 3
3 D EXIT
6 MNOmn o 6
9 WX Y Zw x y z 9
INPUT Space
4
Repeatedly press the corresponding key on the
remote control to highlight the desired character on
the on-screen software keyboard.
5
The highlighted character is entered after you either
press a different key, press c key, or after a twosecond pause.
6
Repeat steps 4 and 5 until you have entered all
desired text.
7
8
When finished, press T.
To remove channel labels:
1
2
Open the Channel Labeling window.
New labels will be added to the list in alphabetical
order and marked with an icon to indicate that
they are custom. Highlight the new custom label and
press T to assign.
Assigned channel labels will be displayed in the
banner, Channel Add/Delete, Channels Block, and
Channel Browser.
To delete the custom label:
1
2
3
If the desired channel label is not available from the list
of presets, you can create a custom label.
Open the Channel Labeling window.
Highlight the label to be deleted and press =.
Highlight Yes from the deletion confirmation
window and press T.
Delete the selected custom label?
No
4
Yes
Highlight Done and press T to save changes, and
go back to the Channel Labeling window.
32
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 33 Tuesday, July 22, 2008 5:25 PM
Chapter 5: Setting up your TV
Setting the HDMI™ audio mode
Viewing the digital signal meter
To set the HDMI audio mode:
You can view the digital signal meter in the ANT/
CABLE digital TV input source only.
1
From the Audio menu, highlight Audio Setup and
press T.
To view the digital signal meter:
2
Press B or b to select HDMI 1 Audio and then press
C or c to select the HDMI 1 audio mode (Auto,
Digital, or Analog). (Auto is the recommended
mode.) See “Connecting an HDMI or DVI device to
the HDMI input” (- page 16).
1
From the Setup menu, highlight Installation and
press T. A new set of Installation menu icons will
appear.
2
Open the Terrestrial menu, highlight Signal Meter,
and press T.
3
Press BbC c to select the digital channel whose
signal you want to check.
Audio Setup
PC Audio
No
Auto
HDMI 1 Audio
MTS
Stereo
Language
English
Optical Output Format
Dolby Digital
Dolby Digital
Dynamic Range Control
Compressed
Reset
3
Done
Mode
Description
Auto
When viewing the HDMI 1 input, if
digital audio from the HDMI input
is available, it will be output. If not,
the TV will automatically detect and
output analog audio from the PC
Audio input.
Digital
When viewing the HDMI 1 input,
digital audio from the HDMI input
will be output.
Analog
When viewing the HDMI 1 input,
analog audio from the PC Audio
input will be output.
Note:
• The physical digital channel number listed in the Signal
Meter screen may not correspond to a virtual TV
channel number. Contact your local broadcasters to
obtain the RF channel numbers for your local digital
stations.
• The signal strength does not change between virtual
channels on the same physical channel.
To close the screen and return to the Terrestrial
menu:
Highlight Done and press T.
To return to normal viewing:
Press O.
To save your settings, highlight Done and press T.
Note: Because the PC and HDMI 1 inputs share the same set
of analog audio inputs, the PC Audio menu setting influences
the HDMI 1 Audio menu setting. If PC Audio is set to “No,” the
HDMI 1 Audio setting changes to “Auto.” If PC Audio is set to
“Yes,” the HDMI 1 Audio setting is set to “Digital” and is
grayed out in the menu. (Also see item 4 on page 11 and
“Setting the PC Audio” on page 51.)
33
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 34 Tuesday, July 22, 2008 5:25 PM
Chapter 5: Setting up your TV
Setting the time zone
Viewing the system status
The Time Zone setup will allow you to specify the correct
time zone for your region. This feature will allow the TV
status information to show the correct time zone
information (- page 55).
To view the system status:
To set the time zone:
1
From the Setup menu, highlight Installation and
press T. A new set of Installation menu icons will
appear.
2
Open the Time Zone menu, highlight Time Zone
Setup, and press T.
3
Press C or c to select the region, highlight Done, and
then press T.
After the time zone has been set, you will be asked to set
the current Daylight Saving Time status.
1
From the Setup menu, highlight Installation and
press T. A new set of Installation menu icons will
appear.
2
Open the System Status menu, highlight System
Information, and press T.
3
Press C c to scroll through the menu bar to select the
Software Version and view the related information.
To close the screen and return to the Installation
menu:
Highlight Done and press T.
To return to normal viewing:
Press O.
To set the Daylight Saving Time status:
Reset Factory Defaults
1
To reset all settings and channels to their factory
default values:
Press C or c to select Yes or No, highlight Done, and
then press T.
1
From the Setup menu, highlight Installation and
press T. A new set of Installation menu icons will
appear.
2
Open the System Status menu, highlight System
Information, and press T.
3
Press C c to scroll through the menu bar to select
Factory Defaults.
4
Enter your PIN code (or 0000 if no PIN code has been
set).
5
Highlight Yes and press T. The TV will turn off
automatically after a few seconds. After the TV turns
off, unplug the TV power cord and then plug it in
again to complete the reset process.
To cancel the reset:
Highlight No and press T.
34
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 35 Tuesday, July 22, 2008 5:25 PM
Chapter 5: Setting up your TV
Selecting the TOSHIBA Illumination
mode
You can set the illumination mode of the TOSHIBA logo
located on the front panel to On or Off.
To set the TOSHIBA Illumination mode:
1
From the Setup menu, highlight TOSHIBA
Illumination and press c.
2
Press B or b to select either On or Off, and press T.
Selecting the Energy Saving Mode
This is a new feature to assist in energy conservation.
You can select either Home or Retail mode.
• Home: Recommended for normal home use.
When selecting this mode, the Auto Brightness Sensor
feature is automatically set to On.
• Retail: Select this mode to use the TV for displaying in
a retail showroom, etc.
When selecting this mode, the Auto Brightness Sensor
feature is automatically set to Off.
To set the Energy Saving Mode:
Selecting the Power-On Mode
You can select either Power-Saving or Fast mode.
• Power-Saving mode keeps power consumption in
standby mode to below 1W. As a result, it takes a bit
longer for the TV to turn on.
• Fast mode increases power consumption in standby
mode. As a result, the TV will turn on more quickly.
While in Fast mode, the yellow LED on the front of the
TV will be lit.
To set the Power-On Mode feature:
1
From the Setup menu, highlight Power-On Mode
and press c.
2
Press B or b to select either Power-Saving or Fast,
and press T.
(Select Power-Saving for optimal energy
efficiency.)
To return to normal viewing:
Press O.
1
From the Setup menu, highlight Energy Saving
Mode and press c.
2
Press B or b to select either Home or Retail, and
press T.
(Select Home for optimal energy efficiency.)
Note: If you change the setting of one of the following Video
menu items: Mode, Picture Settings (any item), Auto
Brightness Sensor, or ColorMaster, the Energy Saving Mode
automatically changes from Retail to Home.
Selecting ENERGY STAR® Qualified
Mode
To ensure your television is operating at optimal energy
efficiency and meets the limits required for ENERGY
STAR qualification:
1
2
From the Energy Saving Mode menu, select Home.
From the Power-On Mode menu, select PowerSaving (see "Selecting the Power-On Mode" on the
left).
Selecting the Demo Mode
You can set the TV’s Demo Mode to On or Off.
This feature is provided for demonstrational purposes
only.
To select the Demo Mode:
1
From the Setup menu, highlight Demo Mode and
press c.
2
Press B or b to select either On or Off, and press T.
Note: If the Demo Mode has been set to On, the Demo Mode
will run automatically when you turn on the TV.
35
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 36 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
Selecting the video input source
to view
To select the video input source to view:
1
2
Note:
• When selecting REGZA LINK input sources from the popup
window using +, some REGZA LINK devices may
automatically turn on.
• When selecting input sources using B b, you will have to
press T to actually select a particular device from the
popup window.
Press + on the remote control or TV control panel.
And then either:
a) Press 0–9; or
b) Repeatedly press Bb on the remote control and
then press T to change the input; or
c) Repeatedly press + on the remote control or TV
control panel to change the input.
The current signal source displays in the top right
corner of the Input Selection screen.
Input Selection
0
1
2
3
4
5
6
7
8
9
ANT/CABLE
ANT/CABLE
Video 1
Video 2
ColorStream HD1
ColorStream HD2
HDMI 1 REGZA LINK
HDMI 2
HDMI 3
HDMI 4
PC
0 - 9 / INPUT / ENTER to Select
Navigate
Note:
• You can label the video input sources according to the
specific devices you have connected to the TV
(- “Labeling the video input sources” at right).
• Sources can also be “hidden” (- “Labeling the video input
sources” at right).
• “No Video Signal” will appear randomly on the screen if no
signal is received in video input mode.
• If a CEC device is connected to an HDMI input, the REGZA
LINK icon will appear.
If a REGZA LINK device with HDMI switching
capability (e.g. Audio Receiver) is connected to
the HDMI input:
Labeling the video input sources
You can label each video input source according to the
type of device you connected to each source, from the
following preset list of labels:
• – – (default label)
• Audio Receiver
• Cable
• Compact Disc
• DTV
• DVD
• Game Console
• HDMI Switch (HDMI inputs only)
• Laser Disk
• PC (HDMI inputs only)
• Satellite/DSS
• VCR
• Video Recorder
• Hide (to hide an unused input in the Input Selection
screen and in the Channel Browser Inputs list)
Note: If you select PC in the Input Selection screen, you can
choose only “– –”, “Game Console”, or “Hide” as the label.
To label the video input sources:
1
2
Press + on the remote or TV control panel repeatedly to
highlight HDMI 1, HDMI 2, HDMI 3, or HDMI 4.
If the connected CEC device has any connected devices,
a separate device selection popup window will appear.
Press + repeatedly to highlight the desired input
source, and then press O.
Press Y and open the Preferences menu.
Highlight Input Labeling and press T.
Preferences
CC Selector
Base CC Mode
Off
Digital CC Settings
Input Labeling
Channel Labeling
Menu Language
English
Channel Browser Setup
3
Press B or b to highlight the video source you want
to label.
36
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 37 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
4
5
Press C or c to select the desired label for that input
source. If a particular input is not used, you can
select Hide as the label, which will cause that input
to be “grayed out” in the Input Selection screen and
skipped over when you press + on the remote
control.
To save the new input labels, highlight Done and
press T.
To revert to the factory default labels, highlight
Reset and press T.
Input labeling example:
The screen below on the left shows the default Input
Selection screen (with none of the inputs labeled as a
specific device). The screen below on the right is an
example of how you could label the inputs if you
connected a VCR to VIDEO 1, Cable TV to VIDEO 2, a
video recorder to ColorStream HD1, a DTV set-top box
to HDMI 1, a satellite/DSS set-top box to HDMI 2, a
DVD player to HDMI 3, and a DVD recorder with tuner
to HDMI 4. Also note that the ColorStream HD2 input is
labeled “Hidden,” which means that input will be
skipped over when + is pressed.
Input Selection
0
1
2
3
4
5
6
7
8
9
ANT/CABLE
0 - 9 / INPUT / ENTER to Select
Input Selection
0
1
2
3
4
5
6
7
8
9
ANT/CABLE
Video 1
Video 2
ColorStream HD1
ColorStream HD2
HDMI 1
HDMI 2
HDMI 3
HDMI 4
PC
Navigate
Input Selection screen with
no inputs labeled.
ANT/CABLE
ANT/CABLE
VCR
Cable
Tuning channels using the
Channel Browser™
The Channel Browser™ provides an easy navigation
interface for all your channels and inputs. This feature
allows you to:
• Navigate the contents of all of your inputs.
• Keep a list of your favorite channels (see “Favorites
Browser,” below).
• Keep a history of the last 32 channels or inputs viewed.
• Quickly surf and tune your recently viewed channels/
inputs from the Channel Browser™ History List
(illustrated on the next page).
• Surf via Browse mode (to immediately tune channels
as you highlight them in the Channel Browser™) or
Select mode (to surf over channels in the
Channel Browser™ before you select one to tune).
• Quickly change inputs from the Inputs List.
• Quickly select REGZA LINK devices from the REGZA
LINK List.
Favorites Browser
Video Recorder
ColorStream HD2 (Hidden)
DTV
Satellite/DSS
DVD
DVD
PC
0 - 9 / INPUT / ENTER to Select
Tuning channels
The Favorites Browser allows you to quickly set up a
favorite channels/inputs list that is integrated into the
Channel Browser™.
Navigate
Input Selection screen with
all inputs labeled except input 4,
which has been hidden.
To clear the input labels:
1
From the Preferences menu, highlight Input
Labeling and press T.
2
Highlight Reset and press T.
To add a favorite channel/input:
1
2
Tune to the channel or input.
Press and hold n on the remote control for 3
seconds.
Note: Additions are added to the beginning of the Favorites list
on the left side of the Channel Browser™.
To delete a favorite channel/input:
1
2
Press n to open the Favorites browser list.
3
Press and hold = for 3 seconds. The channel/input
will be removed from the Favorites list.
Highlight the channel or input to delete by pressing
3 C or # c.
(continued)
37
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 38 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
To set up the Channel Browser™:
1
2
Elements of the Channel Browser™
1
From the Preferences menu, highlight Channel
Browser Setup and press T.
2
Press B to highlight Navigation, and then press C or
c to select either Browse Mode or Select Mode.
88
10
History List
On
ANT/CABLE List
On
Inputs List
On
Favorites List
On
REGZA LINK List
Off
3
Done
Press b to highlight History List, and then press C
or c to select the setting you prefer: either On or Off.
Note: History List will be cleared every time the TV is
powered off.
4
Press b to highlight ANT/CABLE List, and then
press C or c to select On or Off.
5
Press b to highlight Inputs List, and then press C or
c to select On or Off.
6
Press b to highlight Favorites List, and then press
C or c to select On or Off.
7
Press b to highlight REGZA LINK List, and then
press C or c to select On or Off.
Note: REGZA LINK List will be automatically grayed out
and set to Off when Enable REGZA LINK is switched to
Off. (See “To set the REGZA LINK Setup” on page 54 for
more information.)
8
To save your entries, highlight Done and press T.
To return to factory defaults, highlight Reset and
press T.
3
8
WEATHER
6
1
Current list (History, ANT/CABLE, Inputs,
Favorites, or REGZA LINK)
2
Input type
3
Channel or input currently being viewed
4
Channel or input that is currently highlighted in the
browser
5
Channels stored in the History List
6
Channel labels
To toggle among the available lists:
After opening the Channel Browser™, press B or b to
toggle among History, ANT/CABLE, Inputs, Favorites,
and REGZA LINK.
Note:
• The Channel Browser™ opens in History List by default.
Once another list has been selected, the Channel Browser™
will open in the last selected list.
• If all lists are turned off, pressing 3 C, # c, or n will
not display the Channel Browser™. If Favorites List is
turned off, n will have no effect.
• Pressing n will bring up the Channel Browser™
Favorites list regardless of the last selected list in the
Channel Browser™.
To tune to a channel or input in Browse mode:
1
While watching TV, press 3 C or # c to open the
Channel Browser™ and surf back to a previous item
or surf forward to the next item in the list.
In Browse mode, when you stop on an item in the
Channel Browser™, it will be highlighted and the TV
will automatically tune to the channel or input.
2
Press O to close the Channel Browser™.
To open the Channel Browser™:
• Press 3 C or # c on the remote control.
• Press 3 C to surf backward through the previously
tuned 32 channels in the History list, the channels in
the ANT/CABLE channel list, the inputs in the Inputs
list, the REGZA LINK devices in the REGZA LINK list,
or the favorite channels/inputs in the Favorites list.
• Press # c to surf forward through the channel History,
the ANT/CABLE channel list, the Inputs list, the
REGZA LINK list, or the favorite channels/inputs in
the Favorites list.
4
11
ABCHD
5
Select Mode
Reset
2
TVLAND
Channel Browser Setup
Navigation
3
History
To tune to a channel or input in Select mode:
1
While watching TV, press 3 C or # c to open the
Channel Browser™ and surf back to a previous item
or forward to the next item in the list.
In Select mode, when you stop on an item in the
Channel Browser™, it will be highlighted but you
must press T to tune the TV to the highlighted item.
2
3
Press T to tune the TV to the highlighted item.
Press O to close the Channel Browser™.
38
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 39 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
Adding and clearing channels and inputs in the
History List
To set the Channel Tuning Mode:
1
From the Setup menu, highlight Installation and
press T. A new set of Installation menu icons will
appear.
2
Open the Terrestrial menu, highlight Channel
Tuning Mode, press c and B b to select your
desired mode, and then press T.
Adding channels and inputs to the History List:
As a channel or input is tuned, the Channel Browser™
adds it to the History List and displays it on the “right
side” of the Channel Browser™. Previously tuned
channels/inputs are “shifted” to the left, eventually
moving off the left side. Press 3 C to surf backward
through the previously tuned channels/inputs. Any
channel or input that is tuned repeatedly will not be
repeated in the History List but instead will be moved to
the end of the list on the right side of the Channel
Browser™.
The Channel Browser™ will store the following channels:
• All channels that are tuned using the numeric buttons
on the remote control.
• All channels that are tuned for at least 5 seconds using
< or , on the remote control.
Note: Whenever an item is selected that cannot be tuned (for
various reasons), the TV will automatically tune to the
previously viewed channel or input.
Clearing channels from the History List:
• Reconfiguring the ANT/CABLE input will clear the
History List.
Note: See page 30 for details on configuring the antenna
input.
• Once 32 channels or inputs are stored in the History
Note:
• The Channel Add/Delete & Channels Block windows as well
as the Channel Browser ANT/CABLE list will be updated
automatically when you change the mode. Also, the History
List will be cleared, but the Favorites List will be saved.
• Even if the Channel Tuning Mode is set to Digital, analog
channel 3 will still be the default channel to prevent the initial
case where no digital channels have been found in prior
channel scans. (Channel Add/Delete will not have anything
listed until a scan is done.)
Tuning to the next programmed channel
To tune to the next programmed channel:
Press < or , on the remote control or TV control panel.
Note:This feature will not work unless you program channels
into the TV’s channel memory (- page 30).
Tuning to a specific channel (programmed
or unprogrammed)
List, the oldest item will be removed from the list
when a new channel or input is tuned.
• Turning off the TV will clear the History List.
Tuning analog channels:
Setting the Channel Tuning Mode
Tuning digital channels:
This feature allows you to choose how tuning will be
handled for analog and digital channels when the TV is
in Antenna mode.
Enter the major Channel Number (0–9) on the remote
control, followed by the dash (=) button and then the
sub-channel number. For example, to select digital
channel 125-1, press 1, 2, 5, –, 1, then T.
Note: To use this feature, the Input Configuration must be set
to Antenna (- page 30).
The channel tuning mode has three options.
Mode
Description
Standard
Both analog and digital channels can be
tuned normally
Auto
(default)
Digital channels will have priority when
manually entering a channel number
using the Channel Number (0-9) on the
remote control, analog channels can still
be tuned by < / , if available
Digital
Only digital channels can be tuned
Press the Channel Number (0–9) on the remote control.
For example, to select channel 125, press 1, 2, 5, then T.
Note: If a digital channel is not programmed—either through
the automatic channel scan (- page 30) or the channel add/
delete function (- page 31)—you will have to tune the RF
channel using the Physical Channel Number.
Note: Digital mode will be most useful after analog channels
are shut down by the government in 2009.
(continued)
39
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 40 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
Switching between two channels using
Channel Return
Selecting the picture size
The Channel Return feature allows you to switch
between two channels without entering an actual
channel number each time.
You can view many program formats in a variety of
picture sizes—Natural, TheaterWide 1, TheaterWide 2,
TheaterWide 3, Full, 4:3 HD, Native and Dot by Dot.
1
2
Select the first channel you want to view.
3
Press R on the remote control. The previous
channel will display. Each time you press R, the
TV will switch back and forth between the last two
channels that were tuned.
Note: The “picture size” illustrations are examples only. The
format of the image (in any of the picture sizes) will vary
depending on the format of the signal you are currently
watching. Select the picture size that displays the current
program the way that looks best to you.
Select a second channel using the Channel Number
buttons (and the dash (=) button if needed).
Note: If you press R from a non-antenna input, the TV
will return to the last-viewed input.
Switching between two channels using
SurfLock™
You can save separate picture size preferences for each
input on your TV.
To select the picture size using the remote control:
1
2
The SurfLock™ feature temporarily “memorizes” one
channel to the R button, so you can return to that
channel quickly from any other channel by pressing R.
To memorize a channel to the R button:
1
Tune the TV to the channel you want to program
into the R button.
2
Press and hold R for about 2 seconds until the
message “Memorized” appears on-screen. The
channel has been programmed to the R button.
3
You can then change channels repeatedly, and when
you press R, the memorized channel will be
tuned.
The TV will return to the memorized channel one time
only. Once you press R and then change channels
again, the CH RTN memory will be cleared and the
button will function as Channel Return, by switching
back and forth between the last two channels that are
tuned.This feature also works for external inputs.
Press I on the remote control.
While the Picture Size screen is open, you can do
one of the following to select the desired picture size:
• Repeatedly press I.
• Press the corresponding Number button (0–6)
while the Picture Size screen is open.
• Press B or b while the Picture Size screen is
open.
To select the picture size using the menus:
1
From the Video menu, highlight Theater Settings
and press T.
2
Highlight Picture Size and press C or c to select the
desired picture size setting.
3
Highlight Done and press T.
Note: Some of the picture sizes may not be available
depending on the receiving signal format.
Using these functions to change the picture size (i.e.,
changing the height/ width ratio) for any purpose other than
your private viewing may be prohibited under the Copyright
Laws of the United States and other countries, and may
subject you to civil and criminal liability.
Note: If you select one of the TheaterWide® picture sizes, the
top and bottom edges of the picture (including subtitles or
captions) may be hidden. To view the hidden edges, either
scroll the picture (TheaterWide 2 and 3 only) or try viewing the
program in Full or Natural picture size.
40
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 41 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
Picture Size
Picture Size
4:3 HD
(for 720p, 1080i, and 1080p program sources only)
Natural
Some program formats will display with sidebars and/
or bars at the top and bottom.
Picture is not distorted from original size.
TheaterWide 1
(for 4:3 format programs)
Native
(for 480i (HDMI), 480p (HDMI), 720p, 1080i, and 1080p
signal programs)
The center of the picture remains close to its original
proportion, but the left and right edges are stretched
wider to fill the screen.
TheaterWide 2
(for letter box programs)
• If receiving a 480i (HDMI), 480p (HDMI), 720p, 1080i,
or 1080p signal program, Native mode scales the
video to display the entire picture within the borders
of the screen (i.e. no overscanning).
• This is especially useful for external HD sources such
as DVHS movies or PC graphics.
The top and bottom edges of the picture may be
hidden*.
Note:
• This mode is supported only for HDMI (1080p, 1080i,
720p, 480p, and 480i), ColorStream (1080i and 720p), and
ANT/CABLE (digital) inputs (1080p, 1080i, and 720p).
• Depending on the input signals, the border of the picture
may be hidden, displayed in black, or noisy.
TheaterWide 3
(for letter box programs with subtitles)
Dot by Dot
(for VGA, SVGA, XGA, WXGA, and SXGA sources only)
ABCDEFG----------------
ABCDEFG----------------
ABCDEFG--------------------------
The top and bottom edges are hidden*.
Full
(for 16:9 [480i, 480p] source programs only)
“Dot by Dot” is a non-scaling display.
Depending on the input signal format, the picture is
displayed with sidebars and/or bars at the top and
bottom. (Example: VGA input source)
* To view the hidden areas (such as subtitles or captions), see
“Scrolling the TheaterWide® picture” (- page 42).
• If receiving a squeezed 4:3 format program, the
picture is stretched wider to fill the width of the
screen but not stretched taller.
• None of the picture is hidden.
41
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 42 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
Scrolling the TheaterWide® picture
(TheaterWide 2 and 3 only)
You can set separate scroll settings for the TheaterWide
2 and TheaterWide 3 modes for each input.
To set the scroll settings:
1
2
Press Y and open the Video menu.
Highlight Theater Settings and press T.
Using the auto aspect ratio feature
When the auto aspect ratio feature is set to On, the TV
will automatically select the picture size when one of the
following input sources is received:
• A 480i, 480p, 720p, 1080i digital signal from the ANT/
CABLE input
• A 480i signal from the Video 1 or Video 2 input
• A 480i signal from the ColorStream HD1 or HD2 input
• A 480i, 480p, 720p, 1080i, 1080p, or VGA (60/72/
75Hz) signal from the HDMI 1/2/3/4 input
Note: The auto aspect ratio feature is not applicable to the PC
input.
Video
Mode
Sports
Picture Settings
Noise Reduction
Auto Brightness Sensor
ColorMaster
Game Mode
On
Off
Theater Settings
TheaterLock
Off
To turn on the auto aspect ratio feature:
1
From the Video menu, highlight Theater Settings
and press T.
2
3
In the Auto Aspect Ratio field, select On.
To save the new settings, highlight Done and press
T.
To revert to the factory defaults, highlight Reset and
press T.
3
In the Picture Size field, select either TheaterWide
2 or TheaterWide 3 (you cannot scroll in any other
mode).
4
5
Press b to highlight the Picture Scroll field.
To turn off the auto aspect ratio feature:
Press C or c to scroll the picture up and down as
needed, from –10 to +20.
Select Off in step 2 above.
6
To save the new settings, highlight Done and press
T.
To revert to the factory defaults, highlight Reset and
press T.
42
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 43 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
Selecting the cinema mode
(480i and 1080i signals)
When you view a DVD (3:2 pulldown processed) from a
DVD player connected to the Video 1, Video 2,
ColorStream HD1, ColorStream HD2 (component
video), or HDMI inputs on the TV, smoother motion can
be obtained by setting the Cinema Mode to Film.
To set the Cinema Mode to Film:
1
From the Video menu, highlight Theater Settings
and press T.
2
3
In the Cinema Mode field, select Film.
To save the new settings, highlight Done and press
T.
To revert to the factory defaults, highlight Reset and
press T.
To set the Cinema Mode to Video:
Select Video in step 2 above.
Using the FREEZE feature
To use the FREEZE feature:
1
When viewing the TV, press B to make the picture
a still picture.
2
To return to the moving picture, press B again (or
any other button).
Note: If the TV is left in FREEZE mode for more than 15
minutes, the FREEZE mode will automatically be released
and the TV will return to moving picture.
Using the FREEZE function for any purpose other than your
private viewing may be prohibited under the Copyright Laws
of the United States and other countries, and may subject
you to civil and criminal liability.
Adjusting the picture
Selecting the picture mode
You can select your desired picture settings from the
following modes, as described below.
Mode
Picture Quality
AutoView
Automatically adjusts picture settings
based on ambient light conditions and
input signal content
Sports
Bright and dynamic picture
Standard
Standard picture settings
Movie
Lower contrast for darkened room
PC
Designed for viewing of PC tables and
documents
PC Fine
Designed for viewing of media from a
Toshiba REGZA LINK PC.
Preference
Your personal preferences
Note:
• PC mode is available for HDMI and PC inputs only (grayed
out for other input sources).
• PC Fine mode is only available when on an HDMI input with
Enable REGZA LINK set to On and a Toshiba REGZA LINK
PC connected (- page 54).
• Because the AutoView mode automatically adjusts picture
settings based on ambient light conditions and input signal
content, most items in the Picture Settings and Advanced
Picture Settings menus are grayed out when it is selected.
1
2
From the Video menu, highlight Mode and press T.
Press B or b to select the picture mode you prefer
and press T.
Note: The picture mode you select affects the current
input only. You can select a different picture mode for
each input.
Adjusting the picture quality
You can adjust the picture quality (Contrast, Backlight,
DynaLight™, Brightness, Color, Tint, and Sharpness) to
your personal preferences.
Selection
Pressing C
Pressing c
Contrast
lower
higher
Backlight*
darker
lighter
DynaLight**
On/Off
On/Off
Brightness
darker
lighter
Color
paler
deeper
Tint
reddish
greenish
Sharpness
softer
sharper
* Backlight
This feature adjusts the brightness of the entire screen. When in
video mode and no signal is input, this will automatically be set to 0.
(Settings are stored in memory.)
** DynaLight
This function automatically strengthens the black coloring of dark
areas in the video according to the level of darkness.
(continued)
43
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 44 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
To adjust the picture quality:
1
From the Video menu, highlight Picture Settings
and press T.
2
Press B or b to select the picture quality you want to
adjust (Contrast, Backlight, DynaLight,
Brightness, Color, Tint, or Sharpness), and then
press C or c to adjust the setting, as described in the
table above.
3
To save the new settings, highlight Done and press
T.
You can use any of the picture modes (- “Selecting
the picture mode,” above left) as a starting point for
adjusting the picture settings.
To revert back to the base mode that you began
adjusting the picture settings from, highlight Reset
and press T.
The picture qualities you adjusted are automatically
saved in the Preference mode (- “Selecting the picture
mode,” above left) until Reset is selected.
Using the closed caption mode
Base closed captions
The closed caption mode has two options:
• Captions—An on-screen display of the dialogue,
narration, and sound effects of TV programs and
videos that are closed captioned (usually marked
“CC” in program guides).
• Text—An on-screen display of information not related
to the current program, such as weather or stock data
(when provided by individual stations).
To view captions or text:
1
From the Preferences menu, highlight Base CC
Mode and press c.
2
Press B or b to select the desired closed caption
mode and press T.
• To view captions:
Highlight CC1, CC2, CC3, or CC4.
Using the TheaterLock™ feature
The TheaterLock™ feature allows you to “lock” all items
that affect the picture mode setting. In other words, those
settings that when adjusted cause the Mode setting to
automatically change to “Preference” will be grayed out
and unavailable when the TheaterLock setting is set to
“On”. Items that do not influence Mode status will not be
affected e.g., Noise Reduction, Game Mode, etc.
Giant pandas eat leaves.
Note: If the program or video you selected is not closed
captioned, no captions will display on-screen.
• To view text:
Highlight T1, T2, T3, or T4.
To turn on TheaterLock™:
1
From the Video menu, press B or b to highlight the
TheaterLock field, press c and B b to select On,
and press T.
To turn off TheaterLock™:
Select Off in step 1 above.
WORLD WEATHER
LONDON
MOSCOW
PARIS
ROME
TOKYO
Temps
F
C
51
11
57
14
53
12
66
19
65
18
Current
Weather
Clear
Cloudy
Clear
Cloudy
Rain
Note: If text is not available in your area, a black rectangle
may appear on screen. If this happens, set the Base CC
Mode to Off.
• To turn off the closed caption mode:
Select Off in step 2 above.
Note: A closed caption signal may not display in the following
situations:
• When a videotape has been dubbed
• When the signal reception is weak
• When the signal reception is non-standard
Digital CC Settings
You can customize the closed caption display
characteristics by changing the background color,
opacity, text size, type, edge, and color.
44
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 45 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
Note:
• This feature is available for digital channels only.
• You cannot set the Caption Text and Background as the
same color.
2
Press B or b to select Closed Caption, and then
press C or c to select the desired service.
3
Press O.
Mode
Description
Caption Size
Auto, Small, Standard, Large
Adjusting the audio
Caption Text
Type
Auto, Default, Mono w. Serif, Prop.
w. Serif, Mono w/o Serif, Prop. w/o
Serif, Casual, Cursive, Small Capitals
Muting the sound
Caption Text
Edge
Auto, None, Raised, Depressed,
Uniform, Left Drop Shadow, Right
Drop shadow
Caption Text
Color
Auto, Black, White, Red, Green, Blue,
Yellow, Magenta, Cyan
Text
Foreground
Opacity
Auto, Transparent, Translucent,
Flashing, Solid
Background
Color
Auto, Black, White, Red, Green, Blue,
Yellow, Magenta, Cyan
Text
Background
Opacity
Auto, Transparent, Translucent,
Flashing, Solid
Caption Text
Edge Color
Auto, Black, White, Red, Green, Blue,
Yellow, Magenta, Cyan
To customize the closed captions:
1
From the Preferences menu, highlight Digital CC
Settings and press T.
2
Press B or b to highlight the characteristic you want
to change, and then press C or c to select the format
for that characteristic (see table above).
3
To save the new settings, highlight Done and press
T. To revert to the factory defaults, highlight Reset
and press T.
Press W on the remote control to partially reduce (1/2
MUTE) or turn off (MUTE) the sound. Each time you
press W, the mute mode will change in the following
order:
1/2 Mute
Volume
If the closed caption mode is set to Off when you select
“MUTE” mode, the closed caption feature is
automatically activated if the TV program is Closed
Captioned. To mute the audio without automatically
activating the closed caption feature, use Z to set the
volume to 0. See “Using the closed caption mode” (page 44) for more information on closed caption modes.
Using the digital audio selector
You can use the Digital Audio Selector to conveniently
switch between audio tracks on a digital channel (for
those channels that have multiple audio tracks). This
temporarily overrides the audio track chosen by the
language option under Audio Setup (- “Selecting
stereo/SAP broadcasts” on page 46).
To use the digital audio selector:
1
2
CC Selector
You can use the CC Selector to temporarily override the
default analog caption mode (set in Base CC Mode) for
a particular channel. However, once you change to
another analog channel, the closed caption setting will
automatically change back to the current Base CC Mode
setting.
You can also use the CC Selector to select digital closed
caption services (if available). When such services are
not available, the CC Selector presents a default list of
services. If the selected service is not available, the next
best service will be used instead.
Mute
Press Y and open the Audio menu.
Highlight Digital Audio Selector and press T.
Audio
Digital Audio Selector
Audio Settings
Advanced Audio Settings
Audio Setup
3
Press B or b to select Audio, and then press C or c
to select the desired service.
4
Press O.
To select closed captions:
1
From the Preferences menu, highlight CC Selector
and press T.
(continued)
45
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 46 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
Selecting stereo/SAP broadcasts
Adjusting the audio quality
The multi-channel TV sound (MTS) feature allows you to
output high-fidelity stereo sound. MTS also can transmit
a second audio program (SAP) containing a second
language, music, or other audio information (when
provided by individual stations).
When the TV receives a stereo or SAP broadcast, the
word “STEREO” or “SAP” appears on-screen when E
is pressed. The MTS feature is only available for analog
signals on the ANT/CABLE input.
You can adjust the audio quality by adjusting the bass,
treble, and balance.
To listen to stereo sound:
1
From the Audio menu, highlight Audio Setup and
press T.
2
3
In the MTS field, select Stereo.
To adjust the audio quality:
1
From the Audio menu, highlight Audio Settings
and press T.
2
Press b or B to highlight the item you want to adjust
(Bass, Treble, or Balance).
3
Press C or c to adjust the level.
• C makes the bass or treble weaker or increases the
balance in the left channel (depending on the item
selected).
• c makes the bass or treble stronger or increases the
balance in the right channel (depending on the item
selected).
To save the new settings, highlight Done and press
T.
To reset the settings to the factory defaults, highlight
Reset and press T.
4
Note:
• You can typically leave the TV in Stereo mode because
it will automatically output the type of sound being
broadcast (stereo or monaural).
• If the stereo sound is noisy, select Mono to reduce the
noise.
Using the StableSound® feature
To listen to an alternate language on an ATSC
digital station (if available):
Highlight the Language field in step 2 above, and then
press C or c to select the language you prefer.
To listen to a second audio program on an analog
station (if available):
Select SAP in step 2.
Note:
• A second audio program (SAP) can be heard only on those
TV stations that offer it. For example, a station might
broadcast another language as a second audio program. If
you have SAP on, you will see the current program on the
screen but hear the other language instead of the program’s
normal audio.
• If you have SAP on and the station you are watching is not
broadcasting a second audio program, the station’s normal
audio will be output. However, occasionally there is no
sound at all in SAP mode. If this happens, set the MTS
feature to Stereo mode.
To save the new settings, highlight Done and press
T.
To reset the settings to the factory defaults, highlight
Reset and press T.
The StableSound® feature limits the highest volume level
to prevent extreme changes in volume when the signal
source changes (for example, to prevent the sudden
increase in volume that often happens when a TV
program switches to a commercial).
To turn on the StableSound® feature:
1
From the Audio menu, highlight Audio Settings
and press T.
2
3
In the StableSound field, select On.
To save the new settings, highlight Done and press
T.
To revert to the factory defaults, highlight Reset and
press T.
Note: The RESET function returns your audio adjustments
to the following factory settings:
Bass . . . . . . . .
Treble . . . . . .
Balance . . . . .
StableSound .
center (50)
center (50)
center (0)
Off
To turn off the StableSound feature:
Select Off in step 2 above.
46
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 47 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
Selecting the optical audio output format
You can use this feature to select the optical audio output
format when you connect a Dolby Digital decoder or
other digital audio system to the DIGITAL AUDIO OUT
terminal on the TV (- “Connecting a digital audio
system” on page 18).
To select the optical audio output format:
1
2
Using the Locks menu
The Locks menu includes the Enable Rating Blocking,
Edit Rating Limits, Channels Block, Input Lock, Control
Panel Lock, Game Timer, and New PIN Code features.
You can use these features after entering the correct PIN
code.
Tune to a digital source on the ANT/CABLE input.
Entering the PIN code
From the Audio menu, highlight Audio Setup and
press T.
1
3
In the Optical Output Format field, select either
Dolby Digital or PCM, depending on your device.
4
To save the new settings, highlight Done and press
T.
To revert to the factory defaults, highlight Reset and
press T.
Locks
Enable Rating Blocking
Channels Block
Using the
Digital Dynamic Range
Control feature
To use the Dolby Digital Dynamic Range Control:
1
From the Audio menu, highlight Audio Setup and
press T.
2
In the Dolby Digital Dynamic Range Control field,
select Compressed. When Standard is selected, the
audio is output with minimal compression.
3
To save the new settings, highlight Done and press
T.
To revert to the factory defaults, highlight Reset and
press T.
Note:
• This item will be grayed out for NTSC signals, Video,
ColorStream, HDMI, and PC inputs.
• Dolby Digital Dynamic Range Control will function in relation
to Optical Output Format (PCM mode).
Off
Edit Rating Limits
Dolby®
This dynamic range control feature causes the ATSC
dynamic range to be further compressed, allowing you
to switch from digital to analog broadcasts at the same
dynamic range.
On the remote control or TV control panel, press Y
and highlight the Locks menu icon.
Input Lock
Off
Control Panel Lock
Off
Game Timer
Off
New PIN Code
2
Press b, which displays the PIN code entry screen.
• The Lock System screen (below) appears if a PIN
code has not been stored. Press the Channel
Number buttons to enter a new four-digit code,
enter the code a second time to confirm, and press
T.
Lock System
Please enter a 4 digit PIN code
Confirm PIN code
Cancel
Done
• The Locks/Active screen appears if the PIN code
is already stored. Use the Number buttons to enter
your four-digit code and press T.
If the wrong PIN code is entered, the message “Incorrect
PIN code, please try again!” appears. Highlight Retry
and press T. Enter the code again and press T.
When the correct PIN code is entered, the Locks menu
opens.
If you cannot remember your PIN code
While the PIN code entering screen is displayed, press
E four times within five seconds. The PIN code will be
cleared and you can enter a new PIN code.
(continued)
47
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 48 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
Changing your PIN code
1
From the Locks menu, press b to display the PIN
code entering screen.
2
3
4
Enter your four-digit PIN code and press T.
5
Press T. The new PIN code is now active.
Press b to highlight New PIN Code and press T.
Press the Number buttons to enter a new four-digit
code. Reenter the PIN code to confirm it.
Blocking TV programs and movies
by rating (V-Chip)
Some TV programs and movies include signals that
classify the content of the program (violence, sex,
dialogue, language). The V-Chip feature in this TV
detects the signals and blocks the programs according to
the ratings you select. (For rating descriptions, see the
tables on the next page.)
Note: Rating blocking is a function of the V-Chip feature in this
TV, which supports the U.S. V-Chip system only.
Downloading an additional rating system
for blocking TV programs and movies
In the future, an additional rating system may become
available for use in selectively blocking programs.
Note: The currently tuned station must be receiving a digital
signal before an additional rating system can be downloaded.
To download the additional rating system
(if available):
1
From the Locks menu, press b to display the PIN
code entering screen.
2
3
4
5
Enter your four-digit PIN code and press T.
6
Press b to highlight Enable Rating Blocking.
Press c and b to select On, and press T.
Press b to highlight Edit Rating Limits and press
T.
The Edit Rating Limits screen appears.
Highlight Alt RS and press T. The Edit Alternate
Ratings screen will appear.
Note:
• The Alt RS button will only be available if an additional
rating system is currently available.
• It may take several minutes for the TV to download the
additional rating system.
• The information displayed in the Alternate Ratings
screen will depend on the configuration of the
additional rating system available at the time of
download.
To block and unblock TV programs and movies:
1
From the Locks menu, press b to display the PIN
code entering screen.
2
3
4
5
Enter your four-digit PIN code and press T.
Press b to highlight Edit Rating Limits and press
T.
The Edit Rating Limits screen appears.
7
6
Press B b C c and then press T to select the level of
blocking you prefer. A box with an “5” is a rating
that will be blocked.
Press BbC c and then press T to select the level of
blocking you prefer. A box with an “5” is a rating
that will be blocked. As you highlight a rating, a
definition for the rating appears at the bottom of the
screen.
8
When you are finished selecting the ratings you
want to block, highlight Done and press T.
9
In the Edit Rating Limits screen, highlight Done
and press T.
When done selecting the ratings you want to block,
highlight Done and press T.
Note:
• The additional rating system can only be downloaded one
time. You will not be able to download any updates to the
rating system should such updates become available.
• The additional rating system is not designed, transmitted, or
controlled by the TV or Toshiba, nor is the availability of an
additional rating system determined or controlled by
Toshiba. Similarly, the rating of programs in an additional
rating system is not determined, transmitted, or controlled
by the TV or Toshiba.
• The additional rating system is an evolving technology;
therefore, availability, content, and format may vary.
7
Press b to highlight Enable Rating Blocking.
Press c and b to select On, and then press T.
48
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 49 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
Independent rating system for broadcasters
Ratings
Description and Content themes
TV-MA
TV-14
Mature Audience Only (This program is specifically
designed to be viewed by adults and therefore may
be unsuitable for children under 17.)
L) Crude or indecent language S) Explicit sexual
activity V) Graphic violence
Blocking channels
With the Channels Block feature, you can block specific
channels. You will not be able to tune blocked channels
unless you unlock them.
To block channels:
Parents Strongly Cautioned (This program contains
some material that many parents would find
unsuitable for children under 14 years of age.)
D) Intensely suggestive dialogue L) Strong,
coarse language S) Intense sexual situations V)
1
From the Locks menu, press b to display the PIN
code entering screen.
2
Enter your four-digit PIN code and press T
(- page 47).
Intense violence
3
Press b to highlight Channels Block and then press
T.
A list of the channels available for that input will be
displayed along with the call letters for each
channel, if available.
4
Press Bb to highlight the channel you want to block
and press T, which puts an “5” in the box next to
that channel.
5
6
Repeat step 4 for other channels you want to block.
TV-PG
Parental Guidance Suggested (This program
contains material parents may find unsuitable for
younger children.)
D) Some suggestive dialogue L) Infrequent
coarse language S) Some sexual situations
V) Moderate violence
TV-G
General Audience (Most parents would find this
program suitable for all ages.)
TV-Y7,
TV-Y7FV
Directed to Older Children (This program is designed
for children age 7 and above. Note: Programs in
which fantasy violence may be more intense or more
combative than other programs in this category are
designated TV-Y7FV.)
TV-Y
All Children (This program is designed to be
appropriate for all children.)
Independent rating system for movies
Ratings
Description and Content themes
X-rated (For adults only)
X
Not intended for anyone 17 and under
NC-17
Highlight Done and press T.
To unblock individual channels:
In step 4 above, press Bb to highlight the channel you
want to unblock, press T to remove the “5” from the
box, highlight Done and press T.
To block all channels at once:
Highlight Block All in step 4 above and then highlight
Done and press T.
R
Restricted (Under 17 requires accompanying parent
or adult)
To unblock all locked channels at once:
PG-13
Parents Strongly Cautioned (Some material may be
inappropriate for children under 13)
Highlight Allow All in step 4 above and then highlight
Done and press T.
PG
Parental Guidance Suggested (Some material may
not be suitable for children)
G
General Audience (Appropriate for all ages)
Note:
• If you place an “5” in the box next to “None,” programs
rated “None” or “Not Rated” will be blocked; however,
programs that do not provide any rating information will not
be blocked.
• To display the rating of the program you are watching, press
E on the remote control. If it is rated “None,” the word
“NONE” appears in the RECALL screen (as shown below
right). If rating information is not provided, no rating will
appear in the RECALL screen.
TV - PG L V
NONE
Unlocking programs temporarily
If you try to tune the TV to a program that exceeds the
rating limits you set, the TV will enter program lock
mode and the following message will appear on-screen:
This program exceeds the rating limit you set.
Push 'mute' to enter PIN.
You can either temporarily unlock the program or select
an unlocked program to watch.
To temporarily unlock the program:
1
2
Press W.
Enter your four-digit PIN code and press T. If the
correct code is entered, the program lock mode is
released and the normal picture appears. All locking
is disabled until the TV is turned off and will be
enabled when the TV is turned on again.
(continued)
49
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 50 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
Using the input lock feature
You can use the Input Lock feature to lock the video
inputs (Video 1, Video 2, ColorStream HD1,
ColorStream HD2, HDMI 1, HDMI 2, HDMI 3, HDMI 4
and PC) and channels 3 and 4. You will not be able to
view the input sources or channels until you unlock the
inputs.
To lock/unlock the video inputs:
To deactivate the Input Lock once the GameTimer
has activated it:
Set the Input Lock to Off (- “Using the input lock
feature” as described above).
Note:
• A message will appear when 10 minutes, 3 minutes, and 1
minute remain on the GameTimer.
• If the TV loses power with time remaining on the GameTimer,
when power is restored the TV will enter Input Lock mode
(as if the GameTimer had been activated), and you will have
to deactivate the Input Lock (as described above).
1
From the Locks menu, press b to display the PIN
code entering screen.
2
3
4
Enter your four-digit PIN code and press T.
Using the control panel lock feature
Press b to highlight Input Lock and press c.
You can lock the control panel to prevent your settings
from being changed accidentally (by children, for
example). When the control panel lock is On, none of the
controls on the TV control panel will operate except
POWER.
Press B or b to select the level of video input locking
you prefer, as described below.
Mode
Description
Video
Locks Video 1, Video 2,
ColorStream HD1/HD2, HDMI 1,
HDMI 2, HDMI 3, HDMI 4, and PC.
Video+
Locks Video 1, Video 2,
ColorStream HD1/HD2, HDMI 1,
HDMI 2, HDMI 3, HDMI 4, PC and
channels 3 and 4.
• Select Video+ if you play video
tapes via an ANT/CABLE input.
Off
5
Unlocks all video inputs and
channels 3 and 4.
Press T.
Using the GameTimer®
You can use the GameTimer to set a time limit for
playing a video game (30–120 minutes). When the
GameTimer expires, the TV enters Input Lock mode and
locks out the input source for the video game device.
To lock the control panel:
1
From the Locks menu, press b to display the PIN
code entering screen.
2
3
4
Enter your four-digit PIN code and press T.
Press b to highlight Control Panel Lock.
Press c and B b to highlight On and press T. When
the control panel is locked and any button on the
control panel (except POWER) is pressed, the
message “Not Available” appears.
To unlock the control panel:
Highlight Off in step 4 above, or press and hold the
VOLUME – button on the TV control panel for about 10
seconds until the volume icon appears.
To set the GameTimer®:
1
From the Locks menu, press b to display the PIN
code entering screen.
2
3
4
Enter your four-digit PIN code and press T.
Press b to highlight Game Timer and press c.
Press B or b to select the length of time until the
Input Lock is activated (30, 60, 90, or 120 minutes)
and press T.
To cancel the GameTimer®:
Select Off in step 4 above.
50
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 51 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
Using the PC settings feature
Setting the PC Audio
You can view an image from a PC on the TV screen.
When a PC is connected to the TV's PC IN terminal, you
can use the PC Settings feature to make adjustments to
the image.
If the edges of the picture are cut off, readjust the
Horizontal Position and Vertical Position. If the
picture is affected by interference, readjust the Clock
Phase and Sampling Clock.
This function allows you to output or mute the sound
from your PC when connecting using the PC IN terminal
and an analog RGB cable.
To adjust the PC settings:
1
Select PC input mode (- “Selecting the video input
source to view” page 36).
2
From the Setup menu, highlight PC Settings and
press T.
Note: If a PC is not connected or there is no PC input
signal, this feature will be grayed out in the Setup menu.
3
Press B or b to highlight the item you want to
adjust.
4
Press C or c to make the appropriate adjustments.
To set the PC Audio:
1
From the Audio menu, highlight Audio Setup and
press T.
2
Press B or b to select PC Audio and then press C or
c to select No or Yes.
Yes: When viewing the PC input, the audio from
the PC Audio input can be heard.
No: When viewing the PC input, there will be no
audio.
Note: Because the PC and HDMI 1 inputs share the same
set of analog audio inputs, the PC Audio menu setting
influences the HDMI 1 Audio menu setting. If PC Audio is
set to “No,” the HDMI 1 Audio setting changes to “Auto.”
If PC Audio is set to “Yes,” the HDMI 1 Audio setting is
set to “Digital” and is grayed out in the menu. (Also see
item 4 on page 11 and “Setting the HDMI™ audio mode”
on page 33.)
Note: The screen is disrupted momentarily when
adjusting the PC settings. This is not a sign of malfunction.
Mode
Description
Horizontal
Position
Moves the picture left/right.
The adjustment range is within ±10 from
center.*
Vertical
Position
Moves the picture up/down.
The adjustment range is within ±10 from
center.*
Clock Phase
Helps to reduce noise and sharpen the
picture.
The adjustment range is within ±32 from
center.*
Sampling
Clock
Helps to reduce noise and minimize
periodic vertical stripes on the screen.
The adjustment range is within ±5 from
center.*
* The default settings and /or adjustment range vary depending on
the input signal format.
51
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 52 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
Setting the sleep timer
Using REGZA LINK
You can set the sleep timer to turn off the TV after a set
length of time (maximum of 180 minutes).
This is a new feature that uses CEC technology and
allows you to control Toshiba REGZA LINK compatible
devices from the TV remote via HDMI connection (page 17).
When the Enable REGZA LINK in the REGZA LINK
Setup menu (- page 53) is set to On, the following
REGZA LINK functions will be enabled.
To set the sleep timer using the remote control:
Press [ on the remote control to set the length of time
until the TV turns off. Repeatedly press [ to increase
the time in 10-minute increments, or press B or b to
increase or decrease the time in 10-minute increments, to
a maximum of 180 minutes.
To set the sleep timer using the on-screen menus:
1
From the Setup menu, highlight Sleep Timer and
press T.
2
Press the Number buttons to enter the length of time
in 10-minute increments.
3
Highlight Done and press T.
Note: When a power failure occurs, the sleep timer setting
may be cleared.
To display the remaining sleep time:
Press [.
Note: A message will display on-screen when there is one
minute remaining on the sleep timer.
To cancel the sleep timer:
Repeatedly press [ until it is set to 0 minute.
REGZA LINK playback device (DVD player,
etc.) control
With your TV’s remote control, or using the REGZA
LINK Player Control menu, you can control the
connected REGZA LINK playback device you are
watching.
Available remote control key functions:
Before using the following key functions, first set the
MODE SELECT switch on the remote control to TV.
Button
Description
S
Begins playback.
D
Stops playback.
A
Pauses the picture during play or record
mode.
G
Skips forward.
F
Skips backward.
J
Fast-forwards.
H
Rewinds/reverses.
BbCc
Navigates contents menu, etc.
T
Enters contents menu, etc.
R
Returns to the previous menu.
O
Closes the menu.
Note: These functions depend on the devices connected.
52
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 53 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
REGZA LINK Player Control menu functions:
1
2
Press Y and open the Applications menu.
Highlight REGZA LINK Player Control and press
T.
Applications
Channel Browser
Favorites Browser
REGZA LINK Player Control
Start Demo
3
Press B or b to select the item you want to control
and press T.
Item
Description
Power
Turns the select device on and off.
Top Menu
Accesses the top menu of a DVD.
Menu
Accesses the menu of a DVD.
Contents
Menu
Accesses the contents list when you
press T. At this time, the REGZA LINK
Player Control menu will disappear.
Note:
• These functions depend on the devices that are connected.
• The REGZA LINK Player Control item will be grayed out in
the following conditions:
- A non-HDMI input is currently selected.
- The Enable REGZA LINK item is set to Off.
- The connected CEC device is not a playback or recording
device.
REGZA LINK input source selection
If a REGZA LINK device with HDMI switching
capability (e.g. Audio Receiver) is connected to the
HDMI input, you can select another REGZA LINK
device that is connected to the master HDMI device
using the TV’s INPUT button. See page 36 for details.
VOLUME and MUTE controls of Audio
Receiver
With your TV’s remote control, you can adjust or mute
the sound volume of the Audio Receiver. First, set the
MODE SELECT switch on the remote control to TV.
• z Z adjust the volume level.
• W turns off the sound.
Note:
• To use this function:
- Set Speaker Preference to Audio Receiver in the
REGZA LINK Setup menu.
- Confirm that a connected REGZA LINK device (such as
DVD player, etc) is selected for the Audio Receiver input
source.
• You can also use this function when the audio receiver is
connected to the TV’s DIGITAL AUDIO OUT terminal (not
HDMI connection). In this case, select a digital audio input
mode on the Audio Receiver.
• These functions depend on the device connected.
Other REGZA LINK functions
When the Enable REGZA LINK and each item in the
REGZA LINK Setup menu are set to On, the following
functions will be enabled.
Item
Description
TV Auto
Input Switch
If a connected HDMI device starts
playing video or audio, the TV will
automatically switch to the
appropriate HDMI input.
TV Auto
Power
If a REGZA LINK device is turned on,
the TV turns on automatically.
Device Auto
Standby
If the TV is turned off, the TV will send
a message to turn off all of the REGZA
LINK devices connected to the TV.
Speaker
Preference
From this item, you can set your audio
output preference to the TV speakers
or the audio receiver speakers. When
this item is set to Audio Receiver, the
TV remote can be used to adjust or
mute the volume of the audio. This
item will be grayed out unless a
REGZA LINK compatible audio
receiver is connected.
Note: When you turn on the Audio Receiver, change its input
source, or adjust the sound volume, the sound will be output
from the audio receiver’s speakers even if TV Speakers has
been selected. Turn the TV off and on again to output the
sound from the TV speakers.
(continued)
53
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 54 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
To set the REGZA LINK Setup:
1
From the Setup menu, highlight REGZA LINK
Setup and press T.
2
3
Press B or b to highlight Enable REGZA LINK.
Press C or c to select On.
Note: If you set Enable REGZA LINK to Off, the other
items will be grayed out.
4
5
Press B or b to highlight the REGZA LINK setup
item you want to use, and press C or c to select On
or desired mode.
• TV Auto Input Switch: On/Off
• TV Auto Power: On/Off
• Device Auto Standby: On/Off
• Speaker Preference: TV Speakers/Audio Receiver
To save the new settings, highlight Done and press
T.
To revert to the factory defaults, highlight Reset and
press T.
Using the HDMI settings feature
This menu consists of the following items (new HDMI
capabilities) and will be grayed out on non-HDMI
inputs.
Some HDMI legacy sources may not work properly with
your HDMI TV, please try setting the following options
(Lip-Sync Latency and Deep Color) to Off. Adjusting
these settings should allow your HDMI legacy source to
operate properly with your TV.
Note: You must disconnect your source device first before
settings can be adjusted.
• Lip-Sync Latency: On
This option activates an auto audio/video display
timing adjustment function that allows HDMI source
devices to accurately perform synchronization
automatically.
• Deep Color: On (46” and 52” models only)
This feature allows the HDMI source to increase
available colors bits within the boundaries defined by
the RGB or YCbCr color space.
REGZA LINK PC Link
Both of the above HDMI settings need proper HDMI
source devices. If an HDMI source device does not
support these features, the TV may not work properly
when these features are enabled.
This feature automatically sets suitable widescreen
formats and picture preferences when the TV is
connected to a REGZA LINK PC.
Note:This feature depends on the type of equipment
connected.
Note: If your HDMI connection is capable of 1080p and/or
your TV is capable of refresh rates greater than 60Hz or
supports Deep Color, you will need a High Speed HDMI cable.
Conventional HDMI/DVI cables may not work properly with this
mode.
To set the HDMI Settings:
1
Select the appropriate HDMI input mode (HDMI 1,
HDMI 2, HDMI 3, or HDMI 4).
2
From the Setup menu, highlight HDMI Settings and
press T.
3
4
5
Press B or b to highlight the item you want to set.
Press C or c to select On or Off .
To save the new settings, highlight Done and press
T. To revert to the factory defaults, highlight Reset
and press T.
54
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 55 Tuesday, July 22, 2008 5:25 PM
Chapter 6: Using the TV’s features
Displaying TV status information
Understanding the auto power off
feature
To display TV status information using RECALL:
Press E on the remote control.
The following information will display (if applicable):
• Current input (ANT/CABLE, Video 1, etc.)
• If ANT/CABLE is the current input, either “CABLE”
(for cable TV) or “ANT” (for over-the-air broadcasts).
• Channel number (if in ANT/CABLE mode)
• Channel label (if set)
• Digital signal strength indicator (bar graph in lower
right corner of box; for ATSC signal only)
• Stereo, Mono or SAP audio status (when HDMI input
mode, Dolby Digital or PCM)
• Video resolution
• Aspect ratio of incoming video signal (4:3 or 16:9)
• V-Chip rating status
• GameTimer (if set)
ANT
2-2
Stereo
480i
4:3
The TV will automatically turn itself off after
approximately 15 minutes if it is tuned to a vacant
channel or a station that completes its broadcast for the
day. This feature functions in ANT/CABLE mode only.
Understanding the last mode
memory feature
If the power is cut off while you are viewing the TV,
the Last Mode Memory feature automatically turns on
the TV when the power is resupplied.
Note: If it is possible that you will be away from the TV for an
extended period of time, you should unplug the power cord.
NONE
WEATHER
To close the RECALL screen:
Press E again.
To display TV status information using INFO:
(only available for ANT/CABLE input)
Press Q on the remote control.
The following additional information will display for off
air digital channels (if applicable):
• Title
• Duration
• Detailed description
To display Next information, press Q on the remote
control again. Pressing Q a third time will remove the
entire banner.
ANT
2-2
WEATHER
Stereo
480i
Nashville WX Channel
4:3
NONE
8:59am - 4:59pm EST
Nashville WX Channel provides Middle Tenessee and Southern Kentucky
weather.
Note: The location of the banner can be moved to the top or
bottom of the screen by pressing B or b while the RECALL or
INFO display is on-screen. (The last position will be stored to
memory.)
55
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 56 Tuesday, July 22, 2008 5:25 PM
Chapter 7: Using the TV’s advanced features
Using the advanced picture settings
features
Using SRT™ Super Upconversion™
The SRT™ Super Upconversion™ feature allows you to
select the mode and adjust the levels for your desired
picture settings.
To adjust the SRT Super Upconversion settings:
1
2
Press Y and open the Video menu.
Highlight Picture Settings and press T.
To save the new settings, highlight Done and press
T.
To revert to the factory defaults, highlight Reset and
press T.
Note:
• Some of the Advanced Picture Settings features will not be
available for adjustment when the Mode is set to AutoView.
• This feature may not work properly depending on the
content.
• The noise may appear on the image depending on the
device connected to the TV (e.g. a device with specific
enhancer function).
Using dynamic contrast
When dynamic contrast is set to Low, Middle, or High,
the TV will detect changes in the picture quality that
affect the appearance of your contrast settings and then
automatically adjust the video.
Video
Mode
Sports
To select dynamic contrast preferences:
Picture Settings
Noise Reduction
Auto Brightness Sensor
ColorMaster
Game Mode
On
1
From the Video menu, highlight Picture Settings
and press T.
2
Highlight Advanced Picture Settings and press
T.
Off
Theater Settings
TheaterLock
7
Off
3
Highlight Advanced Picture Settings and press
T.
3
4
5
In the Dynamic Contrast field, select either Off,
Low, Middle or High.
Highlight SRT Super Upconversion and press T.
4
To save the new settings, highlight Done and press
T.
To revert to the factory defaults, highlight Reset and
press T.
6
In the Mode field, select either Off, Auto, Mode 1,
Mode 2, or Mode 3.
Mode
Description
Off
Sets this feature Off.
Auto
Changes the setting automatically
depending on each input signal and
resolution.
Mode 1
For low quality content such as a
picture with much noise (e.g. SD
broadcasting)
Mode 2
For middle quality content such as a
picture with less noise (e.g. DVD
Video)
Mode 3
For high quality content such as a
picture with little noise (e.g. HD
broadcasting)
Press B or b to highlight the Level field, and then
press C or c to select either 1, 2, 3, 4, or 5.
Note: If you select one of the following factory-set picture
modes (Sports, Standard, Movie, or PC) and then
change the dynamic contrast setting, the picture mode
automatically changes to Preference.
Using the static gamma feature
The static gamma feature allows you to adjust the levels
of black in the picture.
To adjust the static gamma settings:
1
From the Video menu, highlight Picture Settings
and press T.
2
Highlight Advanced Picture Settings and press
T.
3
In the Static Gamma field, press C or c to adjust the
static gamma.
The adjustment range is within ±5 from center.
• If the setting is moved in the minus direction, the
detail of black colors will be decreased.
• If the setting is moved in the plus direction, the
detail of black colors will be increased.
56
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 57 Tuesday, July 22, 2008 5:25 PM
Chapter 7: Using the TV’s advanced features
4
To save the new settings, highlight Done and press
T.
To revert the factory defaults, highlight Reset and
press T.
Note: If you select one of the factory-set picture modes
(Sports, Standard, Movie, or PC) and then change the
static gamma setting, the picture mode automatically
changes to Preference.
Using CableClear® digital noise reduction
The CableClear® digital noise reduction feature allows
you to reduce visible interference in your TV picture.
This may be useful when receiving a broadcast with a
weak signal (especially a Cable channel) or playing a
noisy video cassette or disc.
To change the CableClear settings:
Selecting the color temperature
1
From the Video menu, highlight Noise Reduction
and press T.
You can change the quality of the picture by selecting
from three preset color temperatures (Cool, Medium,
and Warm), as described below.
2
In the CableClear field, select your desired setting.
Mode
Picture Quality
Cool
blueish
Medium
neutral
Warm
reddish
Note:
• If the current input is ANT/CABLE, Video 1, or Video 2,
the menu will display the text “CableClear.” The
available selections are Off, Auto, Low, Middle, and
High.
• If the current input is ColorStream HD1, ColorStream
HD2, HDMI 1, HDMI 2, HDMI 3, or HDMI 4, the menu
will display the text “DNR.” The available selections are
Off, Auto, Low, Middle, and High. Auto will react
proportionally to the strength of the noise. Low, Middle,
and High will reduce the noise in varying degrees, from
lowest to highest, respectively.
To select the color temperature:
1
From the Video menu, highlight Picture Settings
and press T.
2
Highlight Advanced Picture Settings and press
T.
3
4
Highlight Color Temperature and press T.
5
Press B or b to select either B Drive or G Drive, and
then press C or c to adjust the settings.
• B Drive: c makes the picture blueish.
• G Drive: c makes the picture greenish.
In the Color Temperature field, select the mode you
prefer (Cool, Medium, or Warm).
Note: The B Drive and G Drive settings are connected to
the Color Temperature settings and will change based
on which setting is selected in step 4 above.
6
To save the new settings, highlight Done and press
T.
To revert to the factory defaults, highlight Reset and
press T.
Note: If you select one of the factory-set picture modes
(Sports, Standard, Movie, or PC) and then change the
color temperature mode, the picture mode automatically
changes to Preference.
3
To save the new settings, highlight Done and press
T.
To revert to the factory defaults, highlight Reset and
press T.
Using MPEG noise reduction
The MPEG noise reduction feature allows you to reduce
visible interference caused by MPEG compression.
Choices for MPEG noise reduction are Off, Low, Middle,
and High. Off is automatically selected when this feature
is disabled (“grayed out”).
To select the MPEG noise reduction level:
1
From the Video menu, highlight Noise Reduction
and press T.
2
Press B or b to highlight the MPEG Noise
Reduction field, and then press C or c to select
either Off, Low, Middle or High.
3
To save the new settings, highlight Done and press
T.
To revert to the factory defaults, highlight Reset and
press T.
(continued)
57
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 58 Tuesday, July 22, 2008 5:25 PM
Chapter 7: Using the TV’s advanced features
Using the Auto Brightness Sensor
3
When the Auto Brightness Sensor feature is set to On, the
TV will automatically optimize the backlighting levels to
suit ambient light conditions.
The Color Adjustment window will be displayed.
Press B to freeze the picture.
To return to moving picture, press B again.
Color Adjustment
Red
To turn on the Auto Brightness Sensor
1
2
Hue
From the Video menu, highlight Auto Brightness
Sensor and press T.
Saturation
-
Press B or b to select On or Off and press T.
Note:
• When Energy Saving Mode is set to Retail, this feature
automatically changes to Off.
• When AutoView is selected as the picture mode, the Auto
Brightness Sensor item is grayed out. To set the Auto
Brightness Sensor Off, select an option other than
AutoView as the picture mode (- page 43).
Using the ColorMaster™ feature
The ColorMaster feature allows you to adjust standard
colors.
The menu will consist of 3 items:
ColorMaster, Color Palette Adjustment, and Reset.
To turn on ColorMaster:
Brightness
-
0
+
0
+
0
+
Reset
4
Press B or b to select either Hue, Saturation, or
Brightness, and then press C and c to adjust the
setting.
Note: To revert to the factory settings of the Hue,
Saturation, and Brightness for the selected color,
Highlight Reset and press T.
5
6
Press R to return to the previous menu.
Repeat steps 2 through 5 to adjust any other color.
To reset ColorMaster to its factory settings:
1
From the ColorMaster menu, highlight Reset, and
then press T.
1
From the Video menu, highlight ColorMaster and
press T.
2
A confirmation message will appear. Highlight OK,
and then press T.
2
In the ColorMaster field, select On.
3
Press O.
Note: If you select one of the factory-set picture modes
(Sports, Standard, Movie, or PC) and then change the
ColorMaster setting, the picture mode automatically changes
to Preference.
To turn off ColorMaster:
Select Off in Step 2 above.
Using Color Palette Adjustment
When color palette adjustment is selected, the list of base
colors will be displayed. You can select a base color to
adjust.
Note: To use Color Palette Adjustment, ColorMaster must
be set to On.
To adjust the Base Colors:
1
From the ColorMaster menu, highlight Color
Palette Adjustment and press T.
2
The Select Standard Color window will be
displayed.
Press B or b to highlight the color you want to
adjust, and then press T.
58
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 59 Tuesday, July 22, 2008 5:25 PM
Chapter 7: Using the TV’s advanced features
Using the Game Mode feature
You can use the Game Mode feature for shorter frame
delays when playing a video game requiring splitsecond timing between the on-screen display and input
from the controller (such as music creation and highaction games).
This feature is more effective for 480i and 1080i input
signals.
Note: To use the Game Mode feature, the current video input
must be Video 1, Video 2, ColorStream HD1,
ColorStream HD2, HDMI 1, HDMI 2, HDMI 3, HDMI 4, or PC.
The Game Mode cannot be turned on when the ANT/CABLE
input is selected.
To turn on Game Mode:
1
From the Video menu, press B or b to highlight the
Game Mode field, press c and B b to select On, and
press T.
To turn off Game Mode:
Using the advanced audio settings
features
Using the surround sound features
Stereo Extension, Voice Enhancement, and Dynamic
Bass Boost help to create a thrilling surround sound
experience with deep, rich bass from stereo sound
sources. Your TV’s audio will sound fuller, richer, and
wider.
To adjust the settings:
1
Put the TV in STEREO mode (- “Selecting stereo/
SAP broadcasts” on page 46).
2
From the Audio menu, highlight Advanced Audio
Settings and press T.
3
Press b or B to highlight the feature you want to
adjust, and then press C or c to adjust the item.
Select Off in step 1 above, change the video input, or turn
the TV off and then on again.
Mode
Note: You can change the video input by pressing + on the
remote control (- page 36).
Stereo
Extension
Description
To turn the surround sound effect
On or Off.
Note:If the broadcast is monaural, the
Stereo Extension effect will not work.
Voice
To turn the vocal emphasis effect
Enhancement On or Off.
Dynamic
Bass Boost
4
To select the desired bass expansion
level (Off, Low, or High).
To save the new settings, highlight Done and press
T.
To revert to the factory defaults, highlight Reset and
press T.
59
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 60 Tuesday, July 22, 2008 5:25 PM
Chapter 8: Troubleshooting
General troubleshooting
Before calling a service technician, please check this
chapter for a possible cause of the problem and some
solutions you can try.
Black box on-screen
• The closed caption feature is set to one of the Text modes (T1,
T2, T3, or T4). Set the closed caption feature to Off
(- page 44).
Poor color or no color
• The station may have broadcast difficulties. Try another
channel.
• Adjust the Tint and/or Color (- page 43).
Poor composite or S-video picture
• If the TV is connected to an external A/V device (e.g., DVD
player, video game system, set-top box, etc.) try using a
ColorStream or HDMI video connection instead.
• If you connect an S-video cable, be sure to disconnect the
standard (composite) video cable. Do not connect both types
of video cable at the same time.
Picture and sound are out of sync
TV stops responding to controls
• If the TV stops responding to the controls on the remote
control or TV control panel and you cannot turn off the TV,
press and hold the POWER button on the TV control panel for
5 or more seconds to reset the TV.
Other problems
• If your TV’s problem is not addressed in this Troubleshooting
section or the recommended solution has not worked, use the
Restore Factory Defaults procedure (- page 34).
TV will not turn on
• Make sure the power cord is plugged in, and then press p.
• The remote control batteries may be dead. Replace the
batteries or try the control panel buttons.
Picture problems
General picture problems
• Check the antenna/cable connections (- Chapter 2).
• Press + on the remote control or TV and select a valid video
input source (- page 36). If no device is connected to a
particular input on the TV, no picture will display when you
select that particular input source. For device connection
details, see Chapter 2.
• Antenna reception may be poor. Use a highly directional
outdoor antenna (if applicable).
• The station may have broadcast difficulties. Try another
channel.
• Adjust the picture qualities (- page 43).
• If you are using a VCR, make sure L on the remote control
is set correctly (- page 21).
• Do not connect both a standard video cable and an S-video
cable to the VIDEO 1 input at the same time
(- page 13).
Noisy picture
• If you are watching an analog channel (off-air broadcast or
Cable TV), you can set the CableClear®/DNR feature to AUTO
to reduce visible interference in the TV picture (- page 57).
Video Input Selection problems
• As with all products that contain a digital display, in rare
instances, when viewing certain content (e.g.. television
broadcasts, video games, DVDs), you may notice that the
sound and picture are slightly out of sync. This phenomenon
can be caused by various factors including, without limitation,
video processing within the TV, video processing in an
attached gaming system, and video processing or different
compression rates used by broadcasters in their
programming. You may want to try one or more of the
following suggestions, which may help to reduce the effect of
this phenomenon:
– If the TV is connected to an A/V receiver that has a
programmable audio delay feature, use this feature to help
synchronize the sound to the picture.
– If you notice this phenomenon only on certain TV channels,
please contact your local broadcast, cable, or satellite
provider to inform them of this issue.
LED indications while in reboot from standby
• When you plug the power cord in, the yellow LED will blink
until the TV enters standby mode, (plugged in but not
powered on). This is normal and is not a sign of malfunction.
Sound problems
• Check the antenna/cable connections (- Chapter 2).
• The station may have broadcast difficulties. Try another
channel.
• The sound may be muted. Press VOLUME.
• If you hear no sound, try setting the MTS feature to
Stereo mode (- page 46).
• If you are not receiving a second audio program from a known
SAP source, make sure the MTS feature is set to SAP mode
(- page 46).
• If you hear audio that seems “incorrect” for the program you
are watching (such as music or a foreign language), the SAP
mode may be on. Set the MTS feature to Stereo mode
(- page 46).
• If you connect a PC using either the PC IN terminal or an
HDMI terminal, make sure that the PC Audio setting is
properly set (- page 51).
• If the Input Selection window does not appear when you
press + on the remote control or TV, press + a second
time, which will change to the next video input source and
display the Input Selection window.
Cannot view external signals or channel 3 or 4
• If you cannot view signals from external devices connected to
VIDEO 1, VIDEO 2, ColorStream®, HDMI 1, HDMI 2, HDMI 3,
HDMI 4, PC or from channels 3 or 4, make sure the Input Lock
is set to Off (- page 50).
60
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 61 Tuesday, July 22, 2008 5:25 PM
Chapter 8: Troubleshooting
Remote control problems
• Make sure the remote control is set to the correct device
mode (- page 21).
• Remove all obstructions between the remote control and the
TV.
• The remote control batteries may be dead. Replace the
batteries (- page 20).
• Your TV remote control may not operate certain features on
your external device. Refer to the owner’s manual for your
other device to determine its available features. If your TV
remote control does not operate a specific feature on another
device, use the remote control that came with the device
(- pages 22–26).
• If the TV still does not act as expected, use the Reset Factory
Defaults procedure (- page 34).
HDMI problems
For HDMI cables
• Make sure the HDMI cables with the HDMI Logo (
are used (- page 16).
)
For Deep Color
• You should need to use High Speed HDMI cable to work
properly. Normal HDMI cable or DVI cable may not work with
this option (- page 54).
For Legacy HDMI source
• Some of legacy HDMI sources may not work properly with
latest HDMI TV products, due to new standard adoption.
Please try to set Off the HDMI settings(Lip-Sync Latency,
Deep Color). Your legacy HDMI source should operate
properly with this TV products (- page 54).
Channel tuning problems
• Make sure the remote control is set to the correct device
mode (- page 21).
• The channel may have been erased from the channel memory
by the Channel Add/Delete feature. Add the channel to the
channel memory (- page 31).
• The channel may be blocked by the Channels Block feature.
Unblock the channel (- page 49).
• If you are unable to tune digital channels, check the antenna
configuration (- page 30). If you are still unable to tune
digital channels, clear all channels from the channel list
(- page 31) and reprogram channels into the channel
memory (- page 30). If you are still unable to tune digital
channels, use the Reset Factory Defaults procedure
(- page 34). Also see “TV stops responding to controls”
and “Other problems” (- page 60).
Closed caption problems
• If the program or video you selected is not closed-captioned,
no captions will display (- page 44).
• If text is not available, a black rectangle may appear. If this
happens, turn off the closed caption feature (- page 44).
• A closed-caption signal may not display correctly in the
following situations: a) when a videotape has been dubbed; b)
when the signal reception is weak; or c) when the signal
reception is nonstandard (- page 44).
Rating blocking (V-Chip) problems
• If you forget your PIN code: While the PIN code entering
screen is displayed, press E four times within 5 seconds.
The PIN code you previously stored will be cleared
(- page 47).
• The V-Chip feature is available for the U.S. V-Chip system only
(- page 48).
No REGZA LINK operation
• The REGZA LINK feature is available for Toshiba REGZA LINK
compatible devices.
• Make sure the HDMI cables with the HDMI Logo (
)
are used.
• When the connected REGZA LINK device does not work
correctly after you have changed settings of the device, turn
off your TV and unplug the power cord, then plug and turn on
again.
• If several devices are connected, REGZA LINK feature may not
operate properly.
• Read the instruction manual furnished with the connected
REGZA LINK device.
61
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 62 Tuesday, July 22, 2008 5:25 PM
Chapter 8: Troubleshooting
LED indications
The green and yellow LED lights on the TV front indicate
the TV’s status, as described below.
Note: If the TV loses A/C power (e.g., a power outage occurs
or the power cord is unplugged), when power is restored, the
yellow LED will blink while the TV is booting until the remote
control is usable. This is normal and is not a sign of
malfunction.
TV front
Yellow LED
Green LED
LED Indication
• Green is ON (solid)
The TV is operating properly.
• Yellow is ON (solid)
Standby with Power-On Mode set to Fast.
See “Selecting the Power-On Mode” (- page 35).
• Yellow blinks three times
TV is powering up.
Wait several seconds until the yellow LED stops
blinking.
• Green blinks slowly
Abnormal operation of BUS line.
Turn OFF the TV and unplug the power cord. Plug the
power cord in again and turn ON the TV.
• Green blinks quickly
Power protect detection.
Turn OFF the TV and unplug the power cord. Plug the
power cord in again and turn ON the TV.
If, after trying the solutions, the problem still exists:
• In the U.S., call TACP Consumer Solutions at 1-800631-3811.
• In Canada, locate the nearest Toshiba authorized
service depot by directing your web browser to
www.toshiba.ca; click “Home Entertainment,” and
then click “Support.”
62
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 63 Tuesday, July 22, 2008 5:25 PM
Chapter 9: Appendix
Specifications
Note:
• This model complies with the specifications listed
below.
• Designs and specifications are subject to change
without notice.
• This model may not be compatible with features and/or
specifications that may be added in the future.
Television System
NTSC standard
ATSC standard (8VSB)
Digital Cable (64 QAM, 256 QAM; in-the-clear,
unencrypted)
Channel Coverage
VHF: 2 through 13
UHF: 14 through 69
Cable TV: Mid band (A-8 through A-1, A through I)
Super band (J through W)
Hyper band (AA through ZZ, AAA, BBB)
Ultra band (65 through 94, 100 through 135)
Power Source: 120 V AC, 60 Hz
Power Consumption
42RV535U: 2.1 Arms (maximum current)
0.3 W in standby mode
46RV535U: 2.5 Arms (maximum current)
0.4 W in standby mode
52RV535U: 2.9 Arms (maximum current)
0.4 W in standby mode
Audio Power: 10 W + 10 W
Speaker Type
Main: Two 1-3/8 × 6-3/8 inches (35 × 160 mm)
Video/Audio Terminals
S-VIDEO INPUT:
Y: 1 V(p-p), 75 ohm, negative sync.
C: 0.286 V(p-p) (burst signal), 75 ohm
VIDEO/AUDIO INPUT:
VIDEO: 1 V(p-p), 75 ohm, negative sync.
AUDIO: 150 mV(rms) (30% modulation equivalent,
22 k ohm or greater)
ColorStream® (component video) HD INPUT:
VIDEO:Y: 1V(p-p), 75 ohm
PR: 0.7 V(p-p), 75 ohm
PB: 0.7 V(p-p), 75 ohm
Suggested formats: 1080i, 720p, 480p, 480i
AUDIO: 150 mV(rms), 22 k ohm or greater
HDMI™ INPUT:
HDMI compliant (type A connector)
HDCP compliant
Audio Lip Sync supported
Deep Color supported (10 bit 4:4:4, 12 bit 4:4:4)
Suggested formats: See table on the next page.
HDMI Audio: 2-channel Linear-PCM; 32/44.1/48
kHz sampling frequency; 16/20/24 bits per
sample
FIXED AUDIO OUTPUT:
150 mv (rms) (30% modulation equivalent, 2.2 k
ohm or less)
DIGITAL AUDIO OUTPUT:
Optical type
IR OUT:
3 V(p-p), 3.5 mm mono socket
PC INPUT:
15-Pin D-sub Analog RGB
Dimensions
42RV535U: Width: 39-3/4 inches (1,009 mm)
Height: 27-3/8 inches (694 mm)
Depth: 12-1/4 inches (308 mm)
46RV535U: Width: 43-5/8 inches (1,108 mm)
Height: 29-3/8 inches (746 mm)
Depth: 12-1/4 inches (308 mm)
52RV535U: Width: 49-3/8 inches (1,252 mm)
Height: 33 inches (837 mm)
Depth: 14-1/2 inches (368 mm)
Mass (weight)
42RV535U: 55.1 lbs (25.0 kg)
46RV535U: 58.4 lbs (26.5 kg)
52RV535U: 81.6 lbs (37.0 kg)
Operating conditions
Temperature: 32ºF - 95ºF (0ºC - 35ºC)
Humidity: 20 - 80% (no moisture condensation)
Supplied Accessories
• Remote control with two size “AAA” batteries
• Owner’s manual (this book)
• Securement Clip
Use this clip to attach the TV to a wall stud, pillar, or
other immovable structure. See item 20 on page 3
and instructions on page 5.
• Cleaning cloth (to clean the cabinet and control
panel)
63
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 64 Tuesday, July 22, 2008 5:25 PM
Chapter 9: Appendix
Acceptable signal formats for PC IN and HDMI terminals
PC IN signal formats
Note: Depending on the connected PC, the following status may occur; incorrect display, false format detection, picture position
failure, blur, or judder. This is not a malfunction of your TV.
Format
Resolution
V. Frequency
H. Frequency
Pixel Clock Frequency
VGA
640 × 480
59.940Hz
31.469kHz
25.175MHz
72.809Hz
37.861kHz
31.500MHz
75.000Hz
37.500kHz
31.500MHz
60.317Hz
37.879kHz
40.000MHz
72.188Hz
48.077kHz
50.000MHz
75.000Hz
46.875kHz
49.500MHz
60.004Hz
48.363kHz
65.000MHz
70.069Hz
56.476kHz
75.000MHz
75.029Hz
60.023kHz
78.750MHz
59.995Hz
47.396kHz
68.250MHz
59.870Hz
47.776kHz
79.500MHz
102.250MHz
SVGA
XGA
WXGA
SXGA
800 × 600
1024 × 768
1280 × 768
74.893Hz
60.289kHz
1360 × 768
60.015Hz
47.712kHz
85.500MHz
1280 × 1024
60.020Hz
63.981kHz
108.000MHz
HDMI signal formats
Format
Resolution
V. Frequency
H. Frequency
Pixel Clock Frequency
VGA
640 × 480
59.940Hz
31.469kHz
25.175MHz
72.809Hz
37.861kHz
31.500MHz
75.000Hz
37.500kHz
31.500MHz
60.317Hz
37.879kHz
40.000MHz
72.188Hz
48.077kHz
50.000MHz
75.000Hz
46.875kHz
49.500MHz
60.004Hz
48.363kHz
65.000MHz
70.069Hz
56.476kHz
75.000MHz
SVGA
XGA
WXGA
800 × 600
1024 × 768
1280 × 768
1360 × 768
75.029Hz
60.023kHz
78.750MHz
59.995Hz
47.396kHz
68.250MHz
59.870Hz
47.776kHz
79.500MHz
74.893Hz
60.289kHz
102.250MHz
60.015Hz
47.712kHz
85.500MHz
SXGA
1280 × 1024
60.020Hz
63.981kHz
108.000MHz
480i
720 × 480i
59.940/60Hz
15.734/15.750kHz
27.000/27.027MHz
480p
720 × 480p
59.940/60Hz
31.469/31.500kHz
27.000/27.027MHz
720p
1280 × 720p
59.940/60Hz
44.955/45.000kHz
74.176/74.250MHz
1080i
1920 × 1080i
59.940/60Hz
33.716/33.750kHz
74.176/74.250MHz
1080p
1920 × 1080p
23.976/24Hz
26.973/27.000kHz
74.176/74.250MHz
1080p
1920 × 1080p
59.940/60Hz
67.433/67.500kHz
148.352/148.500MHz
64
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 65 Tuesday, July 22, 2008 5:25 PM
Chapter 9: Appendix
Limited United States Warranty
for LCD Televisions 26” and Larger
Toshiba America Consumer Products, L.L.C. (“TACP”) makes the
following limited warranties to original consumers in the United States.
THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL
CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS LCD
TELEVISION AS A GIFT FROM THE ORIGINAL CONSUMER
PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE.
LCD TELEVISIONS PURCHASED IN THE U.S.A. AND USED
ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT
LIMITATION, CANADA AND MEXICO, ARE NOT COVERED BY THESE
WARRANTIES.
LCD TELEVISIONS PURCHASED ANYWHERE OUTSIDE OF THE
U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA AND MEXICO,
AND USED IN THE U.S.A., ARE NOT COVERED BY THESE
WARRANTIES.
Limited One (1) Year Warranty on Parts and Labor
TACP warrants this LCD Television and its parts against defects in
materials or workmanship for a period of one (1) year after the date of
original retail purchase. DURING THIS PERIOD, TACP WILL, AT TACP’S
OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR
REFURBISHED PART WITHOUT CHARGE TO YOU FOR PARTS OR
LABOR. During this period, TACP Authorized Service Station personnel
will come to your home when warranty service is required. Depending on
the type of repair required, the service will either be performed in your
home or the LCD Television will be taken to a TACP Authorized Service
Station for repair and returned to your home at no cost to you.
Rental Units
The warranty for LCD Television rental units begins on the date of the first
rental or thirty (30) days after the date of shipment to the rental firm,
whichever comes first.
Limited Warranty for Commercial Units
TACP warrants LCD Televisions that are sold and used for commercial
purposes as follows: all parts are warranted against defects in materials
or workmanship for a period of ninety (90) days after the date of original
retail purchase. DURING THIS PERIOD, TACP WILL, AT TACP’S OPTION,
REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR
REFURBISHED PART WITHOUT CHARGE TO YOU.
Owner’s Manual and Product Registration Card
Read this owner’s manual thoroughly before operating this LCD
Television.
Complete and mail the enclosed product registration card or register your
LCD Television online at www.tacp.toshiba.com/service as soon as
possible. By registering your LCD Television you will enable TACP to bring
you new products specifically designed to meet your needs and help us
to contact you in the unlikely event a safety notification is required under
the U.S. Consumer Product Safety Act. Failure to complete and
return the product registration card does not diminish your
warranty rights.
Your Responsibility
THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING
CONDITIONS:
(1) You must retain your original bill of sale or provide other proof of
purchase.
(2) All warranty servicing of this LCD Television must be performed by an
Authorized TACP Service Station.
(3) The warranties from TACP are effective only if this LCD Television is
purchased and operated in the Continental U.S.A. or Puerto Rico.
(4) Labor service charges for set installation, setup, adjustment of
customer controls, and installation or repair of antenna systems are
not covered by this warranty. Reception problems caused by
inadequate antenna systems, misaligned satellite dishes, cable
television distribution, VCRs, DVD players/recorders, personal
computer level IEEE-1394 devices, and any other connected signal
source device are your responsibility.
(5) Warranties extend only to defects in materials or workmanship as
limited above, and do not extend to any LCD Television or parts that
have been lost or discarded by you or to damage to the LCD
Television or parts caused by fires, misuse, accident, Acts of God
(such as lightning or fluctuations in electric power), improper
installation, improper maintenance, or use in violation of instructions
furnished by TACP; use or malfunction through simultaneous use of
this LCD Television and connected equipment; or to units that have
been modified or had the serial number removed, altered, defaced,
or rendered illegible.
How to Obtain Warranty Service
If, after following all of the operating instructions in this manual and
reviewing the section entitled “Troubleshooting,” you find that service is
needed:
(1) To find the nearest TACP Authorized Service Station, visit TACP’s
website at www.tacp.toshiba.com/service or contact TACP’s
Consumer Solution Center toll free at 1-800-631-3811.
(2) You must present your original bill of sale or other proof of purchase
to the TACP Authorized Service Station.
For additional information, visit TACP’s website:
www.tacp.toshiba.com
ALL WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE
U.S.A., INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE EXPRESSLY LIMITED TO THE DURATION OF THE LIMITED
WARRANTIES SET FORTH ABOVE. WITH THE EXCEPTION OF ANY
WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE U.S.A.
AS HEREBY LIMITED, THE FOREGOING WARRANTY IS EXCLUSIVE
AND IN LIEU OF ALL OTHER WARRANTIES, GUARANTEES,
AGREEMENTS, AND SIMILAR OBLIGATIONS OF TACP WITH
RESPECT TO THE REPAIR OR REPLACEMENT OF ANY PARTS. IN NO
EVENT SHALL TACP BE LIABLE FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOST
PROFITS, BUSINESS INTERRUPTION, OR MODIFICATION OR
ERASURE OF RECORDED DATA CAUSED BY USE, MISUSE OR
INABILITY TO USE THIS LCD TELEVISION).
No person, agent, distributor, dealer, or company is authorized to change,
modify, or extend the terms of these warranties in any manner whatsoever.
The time within which an action must be commenced to enforce any
obligation of TACP arising under the warranty or under any statute or law
of the United States or any state thereof is hereby limited to ninety (90)
days from the date you discover, or should have discovered, the defect.
This limitation does not apply to implied warranties arising under the law
of any state of the U.S.A.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU
MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE
TO STATE IN THE U.S.A. SOME STATES OF THE U.S.A. DO NOT
ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED
WARRANTY, WHEN AN ACTION MAY BE BROUGHT, OR THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES. THEREFORE, THE ABOVE PROVISIONS MAY NOT APPLY
TO YOU UNDER SUCH CIRCUMSTANCES.
[0305]
65
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 66 Tuesday, July 22, 2008 5:25 PM
Chapter 9: Appendix
Limited Canadian Warranty
for Toshiba Brand Flat Panel Televisions
Toshiba of Canada Limited (“TCL”) makes the following limited warranties
to original consumers in Canada. THESE LIMITED WARRANTIES
EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY
PERSON RECEIVING THIS TOSHIBA BRAND FLAT PANEL
TELEVISION (the “TELEVISION(S)” or “Television(s)”) AS A GIFT FROM
THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER
PURCHASER OR TRANSFEREE.
TELEVISIONS PURCHASED IN CANADA, AND USED ANYWHERE
OUTSIDE OF CANADA INCLUDING, WITHOUT LIMITATION, THE
UNITED STATES AND MEXICO, ARE NOT COVERED BY THESE
WARRANTIES.
TELEVISIONS PURCHASED ANYWHERE OUTSIDE OF CANADA,
INCLUDING, WITHOUT LIMITATION, THE UNITED STATES AND
MEXICO, AND USED IN CANADA, ARE NOT COVERED BY THESE
WARRANTIES.
Limited One (1) Year Warranty on Parts and Labour
Subject to the more limited warranty if the Television is used for any
commercial or business purposes as set out below, TCL warrants the
Television and its parts against material defects in materials or
workmanship that result in the Television failing for a period of one (1) year
after the date of original retail purchase. DURING THIS PERIOD, TCL
WILL, AT TCL’S OPTION, REPAIR OR REPLACE A DEFECTIVE PART
WITH A NEW OR REFURBISHED PART WITHOUT CHARGE TO YOU
FOR PARTS OR LABOUR.
(a) FOR TELEVISIONS 32 INCHES OR LESS: YOU MUST DELIVER THE
ENTIRE TELEVISION TO A TCL TELEVISION AUTHORIZED
SERVICE PROVIDER (“ASP”). YOU MUST PAY FOR ALL
TRANSPORTATION AND INSURANCE CHARGES FOR THE
TELEVISION TO AND FROM THE ASP.
(b) FOR TELEVISIONS OVER 32 INCHES: During this period, ASP
personnel will come to your home when warranty service is required.
Depending on the type of repair required, the service will either be
performed in your home or the Television will be taken to an ASP for
repair and returned to your home at no cost to you. IN-HOME
SERVICE ONLY APPLIES WITHIN 100 KILOMETERS OF AN ASP.
IF YOU ARE NOT WITHIN 100 KILOMETERS OF AN ASP, YOU
MUST DELIVER THE ENTIRE TELEVISION TO AN ASP. YOU MUST
PAY FOR ALL TRANSPORTATION AND INSURANCE CHARGES
FOR THE TELEVISION TO AND FROM THE ASP.
Limited Warranty for Commercial Units
TCL warrants Televisions that are used for any commercial or business
purposes as follows: all parts are warranted against material defects in
materials or workmanship that result in the Television failing for a period of
ninety (90) days after the date of original retail purchase. DURING THIS
PERIOD, TCL WILL, AT TCL’S OPTION, REPAIR OR REPLACE THE
DEFECTIVE PART WITH A NEW OR REFURBISHED PART WITHOUT
CHARGE TO YOU.
(c) FOR TELEVISIONS 32 INCHES OR LESS: YOU MUST DELIVER THE
ENTIRE TELEVISION TO AN ASP. YOU MUST PAY FOR ALL
TRANSPORTATION AND INSURANCE CHARGES FOR THE
TELEVISION TO AND FROM THE ASP.
(d) FOR TELEVISIONS OVER 32 INCHES: During this period, ASP
personnel will come on-site when warranty service is required.
Depending on the type of repair required, the service will either be
performed on-site or the Television will be taken to an ASP for repair
and returned at no cost to you. ON-SITE SERVICE ONLY APPLIES
WITHIN 100 KILOMETERS OF AN ASP. IF YOU ARE NOT WITHIN
100 KILOMETERS OF AN ASP, YOU MUST DELIVER THE ENTIRE
TELEVISION TO AN ASP. YOU MUST PAY FOR ALL
TRANSPORTATION AND INSURANCE CHARGES FOR THE
TELEVISION TO AND FROM THE ASP.
Rental Units
The warranty for Television rental units begins with the date of first rental
or thirty (30) days from the date of shipment to the rental firm, whichever
comes first.
Your Responsibility
THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING
CONDITIONS:
(1) You must provide your bill of sale or other proof of purchase.
(2) All warranty servicing of this Television must be performed by an ASP.
(3) The warranties from TCL are effective only if the Television is (i)
purchased as new and unopened from TCL or from TCL’s authorized
distributors, dealers or resellers (“ADR’s”) and (ii) located/operated in
Canada.
(4) Labour charges for set installation, setup, adjustment of customer
controls, and installation or repair of antenna systems are not covered
by these warranties. Reception problems caused by inadequate
antenna systems are your responsibility.
(5) Warranties extend only to material defects in materials or
workmanship as limited above, and do not extend to:
a. Service, repairs or replacement made necessary by accident,
misuse, abuse, moisture, liquids, dust, dirt, neglect, accident,
damage, 24/7 applications, improper installation, improper
operation, improper cleaning, improper maintenance, normal
wear and tear, screen burn or image retention caused by
prolonged display of static images and/or phosphor aging, or any
other external cause or event, act or omission outside the control
of TCL, including fire, theft, acts of God, alteration, power failures,
power surges or power shortages, lightning, other electrical
faults, or repairs, modifications or replacements by persons other
than those authorized by TCL to service the Television;
b. Replacement of missing, discarded or lost parts, the provision of
retrofits, or preventive maintenance;
c. Repair of damage that is cosmetic only or does not affect the
Television functionality, such as wear and tear, scratches and
dents;
d. Service on Toshiba-branded accessory items (such accessory
items may be covered by their own warranty);
e. Service on third party products or service made necessary by
use of incompatible third party products;
f. Service made necessary by the simultaneous use of this
Television and connected equipment;
g. Modifications to the Television not approved in writing by TCL,
and service made necessary by the use or installation of nonToshiba modifications to the Television;
h. Service of a Television on which the TOSHIBA label or logo, rating
label or serial number have been defaced or removed;
i. On-site service and repair of the Television; and
j. Damage to the Television caused by failure to follow the
specifications, User manuals or guides as to usage and/or
storage.
66
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 67 Tuesday, July 22, 2008 5:25 PM
Chapter 9: Appendix
Disclaimer and Limitation of Remedy
TO THE EXTENT NOT PRECLUDED BY LAW, ALL OTHER EXPRESS
AND IMPLIED WARRANTIES, CONDITIONS AND REPRESENTATIONS
FOR THIS TELEVISION, INCLUDING THE IMPLIED WARRANTIES,
CONDITIONS AND REPRESENTATIONS OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED
AND EXCLUDED. IF THE APPLICABLE LAW, STATUTORY OR
OTHERWISE, PRECLUDES THE EXCLUSION OF ANY IMPLIED
WARRANTIES, CONDITIONS AND REPRESENTATIONS THEN SUCH
IMPLIED WARRANTIES, CONDITIONS AND REPRESENTATIONS ARE
OTHERWISE LIMITED IN DURATION TO THE TERM OF THIS
EXPRESS WRITTEN LIMITED WARRANTY. TO THE EXTENT NOT
PRECLUDED BY LAW, STATUTORY OR OTHERWISE, THIS WRITTEN
WARRANTY SUPERCEDES AND SPECIFICALLY DISCLAIMS ANY
OTHER WARRANTY, CONDITION OR REPRESENTATION NOT
STATED IN THIS WARRANTY, WHETHER MADE BY TCL, TOSHIBA
CORPORATION, THEIR AFFILIATES, ADRs AND ASPs AND WHETHER
MADE ORALLY OR IN WRITING (INCLUDING ANY STATEMENT IN
ANY BROCHURE, PRESS RELEASE, ANNOUNCEMENT,
ADVERTISEMENT, POINT OF SALE DISPLAY, ETC.).
YOU MUST READ AND FOLLOW ALL SET-UP AND USAGE
INSTRUCTIONS IN THE APPLICABLE USER GUIDES AND/OR
MANUALS. IF YOU FAIL TO DO SO, THIS TELEVISION MAY NOT
FUNCTION PROPERLY AND YOU MAY SUFFER DAMAGE. THIS
WARRANTY WILL NOT COVER ANY SERVICE THAT IS REQUIRED, IN
PART OR IN WHOLE, AS A RESULT OF ANY FAILURE TO FOLLOW THE
SET-UP AND USAGE INSTRUCTIONS. THIS WARRANTY DOES NOT
APPLY AND SHALL BE VOID AND UNENFORCEABLE IF THE
TELEVISION IS OPENED, SERVICED, OR REPAIRED BY PERSONS
OTHER THAN THOSE AUTHORIZED BY TCL TO SERVICE OR REPAIR
THE TELEVISION.
IF THE TELEVISION FAILS TO WORK AS WARRANTED ABOVE, YOUR
SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR REPLACEMENT
OF THE DEFECTIVE PART. IN NO EVENT WILL TCL, TOSHIBA
CORPORATION, THEIR AFFILIATES, ADRs OR ASPs (THE “RELATED
PARTIES”) BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY
DAMAGES, MONEY, REIMBURSEMENT, COSTS OR EXPENSES. THIS
LIMITATION APPLIES TO DAMAGES, MONEY, REIMBURSEMENT,
COSTS OR EXPENSES OF ANY KIND WHATSOEVER INCLUDING ANY
DIRECT OR INDIRECT DAMAGES, DAMAGE TO PROPERTY OR
PERSON, LOST PROFITS, LOST SAVINGS, INCONVENIENCE OR
OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL
DAMAGES, WHETHER FOR BREACH OF WARRANTY, BREACH OF
CONTRACT, TORT (INCLUDING NEGLIGENCE), UNDER A STATUTE OR
UNDER ANY OTHER LAW OR FORM OR ACTION, OR WHETHER
ARISING OUT OF THE USE OF OR INABILITY TO USE THE TELEVISION,
EVEN IF ANY OF THE RELATED PARTIES HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER
PARTY.
No person, agent, distributor, dealer or company is authorized to change,
modify or extend the terms of these warranties in any manner whatsoever.
Arbitration and Dispute Resolution
To the extent not precluded by law, any claim, dispute, controversy or
disagreement (whether for breach of warranty, breach of contract, tort
(including negligence and negligent and/or fraudulent
misrepresentation), under a statute or under any other law or form of
action) against any of the Related Parties arising out of, or otherwise
relating to: (i) this warranty; (ii) the Television; (iii) any oral or written
representations, statements, brochures, press releases, advertising,
announcement, point of sale display, or promotional material relating to
the Television; (iv) the relationships that result from this warranty, (the
foregoing claims, disputes controversies and disagreements are
collectively referred to as the “Dispute”), shall be referred to and resolved
by final and binding arbitration (to the exclusion of the courts). To the
extent not precluded by law, you agree to waive any right that you may
have to commence or participate in any representative or class
proceeding against the Related Parties relating to any Dispute. If and
where applicable and to the extent not precluded by law, you further
agree to opt out of any such representative or class proceedings.
Arbitration of any Dispute will be conducted in the forum and in the
manner as agreed to between you and TCL. Failing such agreement, the
arbitration will be conducted by one arbitrator pursuant to the laws and
rules relating to arbitration generally in force in the jurisdiction in which you
reside at the time that the Dispute arises. To the extent not precluded by
law, no claim, dispute, controversy or disagreement of any other person
may be joined or combined with any Dispute by you, without the prior
written consent of TCL.
Critical Applications
The Television you have purchased is not designed for any “critical
applications.” “Critical applications” means life support systems, medical
applications, connections to implanted medical devices, commercial
transportation, nuclear facilities or systems or any other applications
where Television failure could lead to injury to persons or loss of life or
catastrophic property damage.
IF THE CUSTOMER USES THE TELEVISION IN ANY CRITICAL
APPLICATION, THE CUSTOMER - AND NOT TCL, ITS AFFILIATES, ADRs
OR ASPs - ASSUME SOLE AND FULL RESPONSIBILITY FOR SUCH USE.
TCL RESERVES THE RIGHT TO REFUSE TO SERVICE ANY TELEVISION
USED IN A CRITICAL APPLICATION. TCL, ITS AFFILIATES, ADRs AND
ASPs HEREBY DISCLAIM ANY AND ALL LIABILITY, DAMAGES AND
CONSEQUENCES ARISING OUT OF THE SERVICE OR REFUSAL TO
SERVICE SUCH TELEVISION AND FURTHER DISCLAIM ANY AND ALL
LIABILITY, CONSEQUENCES AND DAMAGES THAT MAY ARISE OR
RESULT FROM THE USE OF THE TELEVISION IN ANY CRITICAL
APPLICATIONS.
General Provisions
If and to the extent that any provision of this limited warranty should
generally be found to be unenforceable, the unenforceable provision shall
be severed from the warranty and deemed not to form part of the warranty.
The remaining provisions of this warranty shall be and remain valid and
enforceable. If and to the extent that any provision of this limited warranty
as it relates to any of the Related Parties is found to be invalid or
unenforceable in respect of that party (the “Excluded Party”), the
Excluded Party shall be deemed to be severed or excluded from the
provision, and the provision shall remain valid, enforceable and
applicable in respect of the other or remaining Related Parties.
To the extent permitted by law, this limited warranty shall be governed and
construed in accordance with the laws of Ontario.
If there is any inconsistency between this limited warranty, on the one
hand, and any statement in the packaging of the Television or in any other
document enclosed with, or used in the context of the promotion or sale
of, the Television, on the other hand, the provisions of this limited warranty
shall prevail.
How to Obtain Warranty Services
If, after following all of the operating instructions in this manual and
checking the “Troubleshooting” section, you find that service is needed:
(1) To find the nearest ASP, visit TCL’s web site at www.toshiba.ca, or
call toll free 1-800-268-3404
(2) Present your bill of sale or other proof of purchase to the ASP.
For additional information, visit TCL’s website at www.toshiba.ca
67
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 68 Tuesday, July 22, 2008 5:25 PM
Chapter 9: Appendix
A copy of the GPL source code in this product may be obtained by
contacting Toshiba Consumer Solutions at (800)631-3811. There will be
a charge to cover the costs of providing the source code.
A copy of the LGPL source code in this product may be obtained by
contacting Toshiba Consumer Solutions at (800)631-3811. There will be
a charge to cover the costs of providing the source code.
Portions of this software are copyright © <2007> The FreeType Project
(www.freetype.org). All rights reserved.
This software is based in part on the work of the Independent JPEG
Group.
68
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 69 Tuesday, July 22, 2008 5:25 PM
Index
A
G
R
Antenna input configuration ............ 30
Audio quality adjustments ............... 46
Audio system connection ................ 18
Auto aspect .................................... 42
Auto Brightness Sensor .................. 58
Auto power off ................................ 55
Game Mode feature ........................ 59
GameTimer®..................................... 50
HDMI audio mode ........................... 33
HDMI settings ................................. 54
Deep Color .............................. 54
Lip-Sync Latency ..................... 54
RECALL button ...............................55
REGZA LINK connection .................17
REGZA LINK feature .......................52
Remote control
Battery installation ....................20
Device code table .....................25
Functional key chart .................23
Programming ...........................24
Base closed captions ...................... 44
Blocking channels .......................... 49
HDMI™ connection .......................... 16
Reset Factory Defaults ....................34
I
S
C
INFO button.................................... 55
INPUT button.................................. 36
Integrated digital tuning ..................... 9
IR blaster........................................ 15
IR OUT connection ......................... 15
SAP sound .....................................46
Satellite receiver connection ............14
Scroll settings .................................42
Sleep timer .....................................52
SRT Super Upconversion ................56
StableSound®................................... 46
Stereo Extension.............................59
Stereo sound ..................................46
SurfLock™ ........................................ 40
System status .................................34
B
CableClear® ..................................... 57
CH Bb buttons ........................ 21, 39
CH RTN button......................... 21, 40
Channel Browser™ ........................... 37
Channel labeling ............................ 32
Channel Number buttons .......... 21, 39
Channel programming
Automatic programming ........... 30
Manually adding and
deleting ..................... 31
Channel Tuning Mode .................... 39
Cinema mode ................................. 43
Closed captions .............................. 44
Color temperature .......................... 57
ColorMaster™ ................................... 58
ColorStream® ................................... 14
Component video ........................... 14
D
Deep Color ..................................... 54
Demo Mode ............................. 29, 35
Digital Audio Out ............................ 18
Digital audio selector ...................... 45
Digital CC Settings ......................... 44
Digital signal meter ......................... 33
Dolby Digital ................................... 18
Dolby Digital Dynamic Range
Control....................................... 47
DVD player connection ................... 14
DVI connection ............................... 16
DynaLight™ ................................... 43
Dynamic Bass Boost ...................... 59
Dynamic contrast............................ 56
E
Energy Saving Mode ...................... 35
F
H
L
Labeling video input ........................ 36
Language selection......................... 29
Last mode memory feature ............. 55
LED indications.........................10, 62
Lip-Sync Latency ............................ 54
LOCKS menu
Channels, blocking................... 49
Enable rating blocking .............. 48
New PIN code.......................... 48
Panel lock................................ 50
Unlocking programs
temporarily ................. 49
Video inputs, locking ................ 50
Locks menu .................................... 47
M
MPEG noise reduction .................... 57
MTS feature ................................... 46
MUTE button .................................. 45
T
TheaterLock™ feature ......................44
TheaterWide® picture size ...............41
Time Zone ......................................34
TOSHIBA Illumination .....................35
TV status information ......................55
V
V-Chip blocking (Locks menu) .........47
VCR connection ....................... 13, 14
Video input label .............................36
Video input lock ..............................50
Voice Enhancement ........................59
O
Optical audio output format ............. 47
P
PC Audio ........................................ 51
PC connection ................................ 19
PC settings ..................................... 51
Picture mode .................................. 43
Picture quality ................................. 43
Picture scroll ................................... 42
Picture size selection ...................... 40
POWER button .........................10, 21
Power-On Mode ............................. 35
FREEZE ........................................ 43
69
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 70 Tuesday, July 22, 2008 5:25 PM
Notes
70
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 71 Tuesday, July 22, 2008 5:25 PM
Notes
71
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 72 Tuesday, July 22, 2008 5:25 PM
Notes
72
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 73 Tuesday, July 22, 2008 5:25 PM
Notes
73
RV535U (E/F) Web 213:276
52RV535U_EN.book Page 74 Tuesday, July 22, 2008 5:25 PM
Corporate Headquarters: 82 TOTOWA ROAD, WAYNE, NJ 07470, U.S.A.
NATIONAL SERVICE DIVISION: 1420-B TOSHIBA DRIVE, LEBANON, TN 37087, U.S.A.
HEAD OFFICE: 191 McNABB STREET, MARKHAM, ONTARIO, L3R 8H2, CANADA – TEL: (905) 470-5400
SERVICE CENTERS:
TORONTO: 191 McNABB STREET, MARKHAM, ONTARIO L3R 8H2, CANADA – TEL: (905) 470- 5400
MANUFACTURED BY
CableClear, ColorStream, GameTimer, StableSound, and TheaterWide are registered trademarks of Toshiba America Consumer Products, L.L.C.
Channel Browser, SurfLock, DynaLight, ColorMaster, SRT, Super Upconversion and TheaterLock are trademarks of Toshiba America Consumer Products,
L.L.C.
REGZA is a registered trademark of Toshiba Corporation.
PRINTED IN USA
(08-08)
RV535U (E/F) Web 213:276