Late to Test - Safeguard Security

If you have received an automated telephone call from Safeguard informing you that we have not received an automated fire or security test signal from
your alarm system, please identify your system from among those pictured below. Call Safeguard at (480) 609-6363 and ask the Monitoring Center to put
your system on test and follow the corresponding instructions to perform a quick communications test from your system to our Monitoring Center. If the
test fails, exit TEST MODE as instructed and call Safeguard at (480) 609-6363.
Note: The Master Code (referred to in these instructions) is the primary code you use to arm/disarm the system and/or modify (add/delete) user codes.
PANEL TYPE
Honeywell LYNXR/LYNX Plus
Honeywell LYNX Touch
Honeywell Vista Panels
STEPS TO PERFORM
COMMUNICATIONS TEST
Enter Master Code + 5
WHAT IS DISPLAYED IF
SUCCESSFUL
Nothing displayed
WHAT IS DISPLAYED IF
FAILED
TO EXIT TEST MODE
FC
Enter the Master Code + 1.
Please contact our Monitoring
Station.
Notify the Monitoring Center
that you have completed
your test.
ACK Message not received.
Press UNLOCK button.
Enter Master Code.
Press TOOLS icon,
Enter Master Code,
Press TEST icon,
Press COMM TEST icon,
Press SEND GSM MESSAGE
ACK Received
Enter Master Code 5 + 1
Alpha keypads will display Alpha keypads will display
“Phone Okay”.
“Comm Fail”, LCD keypads will
LCD keypads will display
display FC.
nothing.
Please contact our Monitoring
Station.
Please contact our Monitoring
Station.
Notify the Monitoring Center
that you have completed
your test.
Enter Master Code + 1
Notify the Monitoring Center
that you have completed
your test.
PANEL TYPE
2GIG
Concord 4
DSC
STEPS TO PERFORM
COMMUNICATIONS TEST
WHAT IS DISPLAYED IF
SUCCESSFUL
From Home Screen, press
SECURITY, MENU, TOOLBOX.
Enter Master Code,
Use ← & → arrows to select
Toolbox Screen (3 of 3).
On the Toolbox Screen, press
CELL PHONE TEST,
Enter the Master Code to begin
the test.
The test is successfully
and the cell phone is
working correctly.
8 + Master Code + 4
Nothing displayed.
Press *, 6 + Master Code + 4
Nothing displayed.
Trouble light will
disappear if successful.
WHAT IS DISPLAYED IF
FAILED
Unable to complete test.
Please contact our Monitoring
Station.
TO EXIT TEST MODE
Push OK, then press Home
button.
Notify the Monitoring Center
that you have completed
your test.
Comm test failed.
Will time out automatically.
Please contact our Monitoring
Station.
Notify the Monitoring Center
that you have completed
your test.
Trouble light will flash.
Press * 2; Zone 4 light will
turn on.
Press #.
Please contact our Monitoring
Station.
Notify the Monitoring Center
that you have completed
your test.
PANEL TYPE
Interlogix (GE Security)
SIMON 3
Interlogix (GE Security)
SIMON XTi
Interlogix (GE Security)
SIMON XT
STEPS TO PERFORM
COMMUNICATIONS TEST
WHAT IS DISPLAYED IF
SUCCESSFUL
WHAT IS DISPLAYED IF
FAILED
Open keypad cover.
Enter Master Code using RED
number keys.
Press TEST 2 times – keypad says
“Phone Test is On”.
Keypad says “Phone Test
OK” in 2 minutes.
Keypad says “Phone
Communication Failure” in 10
minutes.
Open Status & Settings menu.
Scroll to SYSTEM TESTS, press
ENTER.
Enter Master Code and press OK.
Press COMM TEST.
GSM test signal sent OK.
Check Central Station
Report (no need for
further verification).
Fail to Communicate.
Press CLOSE 3 times.
Please contact our Monitoring
Station.
Notify the Monitoring Center
that you have completed
your test
Scroll to SYSTEM TESTS, press
ENTER.
Enter Master Code and press
ENTER.
Scroll to COMM TEST, press
ENTER – display shows “Comm
Test is On”.
Display: Comm Test OK.
Display: Comm Test Failure.
Will time out automatically.
Please contact our Monitoring
Station.
Notify the Monitoring Center
that you have completed
your test
Please contact our Monitoring
Station.
TO EXIT TEST MODE
Close cover.
Notify the Monitoring Center
that you have completed
your test
PANEL TYPE
DMP
Radionics
Napco
STEPS TO PERFORM
COMMUNICATIONS TEST
WHAT IS DISPLAYED IF
SUCCESSFUL
WHAT IS DISPLAYED IF
FAILED
TO EXIT TEST MODE
Press CMD until it reads Menu?.
Press YES key.
Press CMD key until System Test,
press any top key to begin test.
Keypad will test Bell, Battery and
Transmit and report status of
each.
Transmit Okay.
Press COMMAND 4 + 1
LCD Keypads will beep for LCD Keypads will not sound.
2 seconds.
Alpha keypads will display
Alpha keypads will display “Comm Fail”.
“Report Sent”.
Please contact our Monitoring
Station.
Will time out automatically.
Monitoring Center will
confirm that a signal was
received.
Enter Master Code to disarm
the alarm.
Secure all zones to light the
Status Light on keypad.
Enter Master Code followed by P
or Q to arm system.
Open a door/window to sound
the alarm; letting it ring for 10
seconds.
Enter Master Code, then U to
silence alarm.
Call Monitoring Center.
Transmit Fail.
Will time out automatically.
Please contact our Monitoring
Station.
Notify the Monitoring Center
that you have completed
your test.
Monitoring Center will inform
you that a signal was not
received.
Notify the Monitoring Center
that you have completed
your test.
Notify the Monitoring Center
that you have completed
your test.
PANEL TYPE
Aegis
STEPS TO PERFORM
COMMUNICATIONS TEST
WHAT IS DISPLAYED IF
SUCCESSFUL
WHAT IS DISPLAYED IF
FAILED
Secure all zones and press “2” to
enter “Security” menu. Select “5
= DAY INST”.
Monitoring Center will
confirm that a signal was
received.
Monitoring Center will inform
you that a signal was not
received.
Secure all zones (green “Ready”
light is on) and enter Master
Code + {INSTANT}.
Monitoring Center will
confirm that a signal was
received.
Monitoring Center will inform
you that a signal was not
received.
Secure all zones (green “Ready”
light is on) and enter Master
Code + {INSTANT}.
Open a door/window to sound
the alarm; letting it ring for 10
seconds. Call Monitoring Center.
Enter Master Code to disarm
the alarm.
Notify the Monitoring Center
that you have completed
your test.
Open a door/window to sound
the alarm; letting it ring for 10
seconds. Call Monitoring Center.
Optex
Enter Master Code to disarm
the alarm.
Notify the Monitoring Center
that you have completed
your test.
Open a door/window to sound
the alarm; letting it ring for 10
seconds. Call Monitoring Center.
Morse
TO EXIT TEST MODE
Monitoring Center will
confirm that a signal was
received.
Monitoring Center will inform
you that a signal was not
received.
Enter Master Code to disarm
the alarm.
Notify the Monitoring Center
that you have completed
your test.
PANEL TYPE
HMS
STEPS TO PERFORM
COMMUNICATIONS TEST
WHAT IS DISPLAYED IF
SUCCESSFUL
WHAT IS DISPLAYED IF
FAILED
Secure all zones and press “2” to
enter “Security” menu. Select “5
= DAY INST”.
Monitoring Center will
confirm that a signal was
received.
Monitoring Center will inform
you that a signal was not
received.
Enter Master Code + 8 on the
keypad and then wait a minute.
Enter Master Code to disarm
the alarm.
Notify the Monitoring Center
that you have completed
your test.
Open a door/window to sound
the alarm; letting it ring for 10
seconds. Call Monitoring Center.
ITI
TO EXIT TEST MODE
The keypad will sound a
single 3 second beep to
confirm that a signal was
received.
After several minutes of the
signal not getting through, the
keypad will start a sequence
of six beeps, then a pause, six
beeps, then a pause… and do
so until acknowledged.
Enter Master Code to arm
the system, wait a minute,
and then disarm the alarm.
Notify the Monitoring Center
that you have completed
your test.
Please contact our Monitoring
Station.
Moose
Press 2 and Reset (*) key.
The Read light will blink until the
test is completed.
The Read light will stop
blinking and no “trouble
condition” will appear on
keypad.
The keypad will indicate a
trouble condition.
Please contact our Monitoring
Station.
Will time out automatically.
Notify the Monitoring Center
that you have completed
your test.
Download PDF