ST2-KP Keypad - Full Compass

ST2-KP Keypad - Full Compass
Keypad Operation
Turning the keypad on/off
To activate the ST2-KP, press
. Press
to power
down the keypad display. The keypad remains powered
until the ST2 Tuner is turned off.
Technical Specifications
Selecting the desired frequency
press and hold either
or
for more than 1.5 seconds. European frequencies show in .05 MHz increments.
Recalling a Memory Preset
To select a different tuner, press and hold
. (If the keypad has been hardware selected to Tuner 1 or Tuner 2, it
will not switch between the two tuners.) The backlight color
of the display will be green for Tuner 1 and amber for
Tuner 2. Each time a tuner is selected the display will
refresh with the current station or preset for that tuner, and
all subsequent button presses and memory preset entries
will be associated with that selected tuner.
To recall a memory preset, press and release
or
to scroll through the presets for the selected bank.
(Memory presets must be stored for ST2-KP recall)
Selecting a Bank
To select a bank, select the desired tuner, then press and
hold
or
to select the desired bank. The bank
name will show on the display.
Selecting the desired band (operating mode)
Push
to switch between AM/FM band, or XM operating
modes. Refer to the ST2-XM Tuner manual for mode
details.
Weight:
5 oz. (141g)
Power Requirements: 12 VDC 150mA
ST2-KP Keypad
The ST2-KP keypad is an in-wall single-gang keypad that is
designed to control the ST2 Dual Tuner (AM/FM/XM). It has a
backlit LCD panel and soft-touch control buttons.
110 punchdown
Warranty Repair
The Russound ST2-KP is fully guaranteed against all defects in materials and
workmanship for two (2) years from the date of purchase. During this period,
Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor.
ST2-KP Keypad-Front Panel
For this warranty to apply, the unit must be installed and used according to its
written instructions. If service is necessary, it must be performed by
Russound. The unit must be returned to Russound at the owner's expense and
with prior written permission. Accidental damage and shipping damage are
not considered defects, nor is damage resulting from abuse or from servicing
by an agency or person not specifically authorized in writing by Russound.
1
This Warranty does not cover: Damage caused by abuse, accident, misuse,
negligence, or improper installation or operation; Power surges and lightning
strikes; Normal wear and maintenance; Products that have been altered or
modified; Any product whose identifying number, decal, serial number, etc.
has been altered, defaced or removed.
2
Russound sells products only through authorized Dealers and Distributors to
ensure that customers obtain proper support and service. Any Russound product purchased from an unauthorized dealer or other source, including retailers, mail order sellers and online sellers will not be honored or serviced under
existing Russound warranty policy. Any sale of products by an unauthorized
source or other manner not authorized by Russound shall void the warranty on
the applicable product.
Utility Menu for ST2-KP
Hold
3
2
5
4
Damage to or destruction of components due to application of excessive
power voids the warranty on those parts. In these cases, repairs will be made
on the basis or the retail value of the parts and labor. To return for repairs,
the unit must be shipped to Russound at the owner's expense, along with a
note explaining the nature of service required. Be sure to pack the unit in a
corrugated container with at least three (3) inches of resilient material to protect the unit from damage in transit.
Utility Menu
Note: For the ST2-KP to operate properly, the ST2 Tuner
must be configured with Tuner 1 as Source 1, and Tuner 2
as Source 2. If this is not the case, refer to the ST2 Tuner
Instruction Manual, Setup Menu section, to set source
numbers. Configure Tuner 1 as Source 1, and Tuner 2 as
Source 2.
1.875"W x 1.125"D x 4.3"H
(4.8 x 10.9 x 2.8 cm)
Fits 1 Gang UL/CSA Approved Junction Box
CAT-5 Connection:
Selecting the desired tuner
The Utility Menu allows the installer to run a diagnostic
check on the keypad and to verify the firmware version.
The Utility Menu also contains the update firmware procedure for updating the ST2-KP’s firmware. To access the
Utility Menu, press and release the Setup button on the
right side of the keypad. The menus are outlined in the
diagram at right. When finished, press and release the
Setup button until normal operating mode returns. If performing Update Firmware, the power must be cycled.
Dimensions:
Use
and
for manual tuning (AM/FM) and channel
up and down (XM). To move quickly through the channels,
DIAGN
(Diagnostics)
This
Procedure
is for
Factory
use
ONLY
VER
(Version)
UDFRM
(Update
Firmware)
Before returning a unit for repair, call Russound at (603) 659-5170 for a
Return Authorization number. Write this number on the shipping label and ship
to: Russound, ATTN: Service, 5 Forbes Road, Newmarket, NH 03857
Due to continual efforts to improve product quality as new technology and
techniques become available, Russound/FMP, Inc. reserves the right to revise
system specifications without notice.
Displays current
firmware version
HOLD
BAND
All trademarks are property of their respective owners.
After update
cycle Power
Start
Update
Cycle Power
5 Forbes Road, Newmarket, NH 03857
tel 603.659.5170 • fax 603.659.5388
e-mail: tech@russound.com
www.russound.com
1
LCD PANEL - 5-character backlit display shows
frequency and band (messages scroll twice, then show first
5 characters)
2
FREQUENCY SELECT - Manual station tuning (European
frequencies show in .05 MHz increments)
3
BAND - Selects band (AM/FM); selects Operating Mode (XM)
4
POWER - Turns lighted keypad display on or off
4
TUNER SELECTION - Press and hold to select TUNER 1 or
TUNER 2 (unless jumper set for specific tuner)
5
BANK SELECT - Used for bank selection (press and hold)
5
MEM UP/DOWN - Scrolls through memory preset stations
for selected bank (press and release)
ST2-KP Side Panel
ST2-KP Back Panel
Safety Instructions
The ST2-KP’s setup button, OS update pins and hardware tuner select pins are
located on the right side of the keypad (when facing front).
CAT-5 Connection
1. Read Instructions - All the safety and operating instructions should be
read before the appliance is operated.
1
OS Update/Run Jumper -The pins are jumpered when performing an OS update
on the keypad, and the jumper is left on one pin during normal operation.
(Typically needed only on a keypad that has never been updated)
1
TNR2
2
3
4
Hardware Selected Tuner Jumper - The ST2-KP can be set to select only Tuner 1
(jumper on bottom two pins) or Tuner 2 (jumper on top two pins), or to select
both tuners (no jumper or simply store jumper on a single pin).
2
TNR1
Setup Button - Activates information and update menus for the keypad.
3
OS Update Port - Used to update the ST2-KP keypad operating system firmware.
If an update is released, it will be available online through the Document Center
on www.russound.com. Look for it in the “Firmware and Downloads” section
under Multi-Zone product type. The Advanced Programming Cable is available
from Russound, Part #2500-521065.
4
1
OS update
mode selected
4
Tuner 1 + 2
selected
2
2. Retain Instructions - The safety and operating instructions should be
retained for future reference.
3. Heed Warnings - All warnings on the appliance in the operating instructions should be adhered to.
4. Follow Instructions - All operating and user instructions should be followed.
5. Water and Moisture - The appliance should not be used near water; for
example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.
6. Wall Mounting - The appliance should be mounted to a wall only as
recommended by the manufacturer.
7. Heat - The appliance should be situated away from heat sources such as
radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
8. Power Sources - The appliance should be connected to a power supply
only of the type described in the operating instructions or as marked on
the appliance.
Take care when using an impact 110
punchdown tool, as this may overspread the contact points. Use of the
impact tool may propel stray bits of
wire and jacket into the keypad’s chassis and possibly cause a short in the circuitry. Gently shake or blow air through
the keypad chassis to remove stray
wire before the keypad is installed into
the junction box.
ST2-KP Side View
Tuner 2
selected
The ST2-KP keypad uses a 110punchdown terminal on the back
panel to provide a simple installation
and strong connection for CAT-5
cable’s eight conductors. Punchdown
terminals require the use of a punchdown tool. Attach the CAT-5 cable to
the 110-punchdown terminal on the
ST2-KP keypad as shown, matching
the conductor colors to the connection color guide. The keypad will not
operate properly if the terminations
deviate from the required connection
order.
Data Rx TTL Level
Data Tx TTL Level
GND
10.Damage Requiring Service - The appliance should be serviced by qualified service personnel when:
A.
C. The appliance does not appear to operate normally; or
D. The appliance has been dropped.
Keypad Installation
1. Check whether or not you can route the wire to the location you
have chosen.
2. To install a single-gang keypad, you will need to use a UL/CSA
approved plastic single-gang (18 ci) electrical box or a low voltage
mounting ring.
3. Route CAT-5 wire to the junction box from the ST2 tuner.
4. Use a 110 punchdown tool to connect each wire to its corresponding color labeled on the punchdown terminal.
Keypad to ST2 Connection
5. Mount the keypad in the electrical box and attach the cover plate.
The ST2 tuner supports up to two ST2-KP keypads. An SA-ZX3 Keypad Splitter
can be used to add additional keypads.
CAT-5 Cable
Objects have fallen, liquid has been spilled into the appliance; or
B. The appliance has been exposed to rain; or
+12VDC
Note: Do not put RS-232level signals into the pins.
Must use Advanced
Programming Cable P/N
2500-521065.
Tuner 1
selected
9. Object and Liquid Entry - Care should be taken so that objects do not fall
and liquids are not spilled into the enclosure through the openings.
The ST2-KP connects to the ST2 tuner with CAT-5 cable.
The keypad connects to the ST2 tuner with an RJ-45 (T568A) jack on the tuner
connection end of the cable.
Be sure to use the keypad ports for the ST2-KP and NOT the RNET link ports.
Note: ST2-KP keypads are not to be used when the ST2 Tuner is a component
of an RNET™ controller such as the CAV6.6. The RNET-system keypads are
capable of providing all functions of the ST2-KP.
Junction Box
ST2-KP
Back Plate
Cover Plate
11.Servicing - The user should not attempt to service the appliance beyond
that described in the operating instructions. All other servicing should be
referred to qualified service personnel.
Precautions:
1. Do Not Touch The Unit With Wet Hands – Do not handle or touch the
keypad when your hands are wet or damp. If water or any other liquid
enters the ST2-KP’s cabinet, take the unit to a qualified service person
for inspection.
2. Care – From time to time you should wipe off the front panel with a soft
cloth. Do not use rough material, thinners, alcohol or other chemical solvents or cloths since this may damage the finish or remove the panel
lettering.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising