Data Sheet 85001-0349 -- Intelligent Break Glass Call Point

GE
Security
EST Fire & Life Safety
Intelligent Initiating Devices
Overview
Standard Features
SIGI-271 Fire Alarm Call Points are part of GE’s Signature Series system. These integrated assemblies feature the familiar KAC Installers’
Series Call Point packaged with Signature Series intelligent addressable/analogue interface electronics.
• Intelligent Device with Integral Microprocessor
All decisions are made at the Call Point to allow lower communication speed. Lower communication speeds are less sensitive to
line noise; twisted or shielded wire is not required.
In all 271 Series Call Points, the switch is held off by the edge of the
glass. When the glass is broken by pressing directly on it, the switch
is released and an alarm sent to the Signature loop controller. A
protective plastic coating on the glass prevents operator injury and
inhibits the release of glass fragments.
• Automatic Device Mapping
Each Call Point transmits wiring information regarding its location with respect to other Signature devices on the circuit.
Each Signature Series Call Point constantly runs self-checks to
provide important maintenance information. The results of the
self-check are automatically updated and permanently stored in the
Call Point’s non-volatile memory. This information is accessible for
review any time at the control panel, PC, or by using the SIGA-PRO
Signature Program/Service Tool.
The information stored in the Call Point’s memory includes:
• Call Point serial number, address, type code.
• Manufacture date, hours of operation, last maintenance date.
• Number of recorded troubles, alarms, time and date of last alarm.
• Up to 24 possible trouble codes that may be used to specifically
diagnose faults.
The Signature loop controller learns where each device’s serial
number address is installed relative to other Signature devices on
the circuit. The loop controller keeps a “map” of the Signature Series
devices connected to it.
• Electronic Addressing
Addresses are downloaded from a PC, or the SIGA-PRO Signature
Program/Service Tool. There are no switches or dials to set.
• Non-volatile Memory
Permanently stores serial number, type of device, and job number. Automatically updated with historic information.
• Stand-alone Operation
Call Point can input an alarm even if the loop controller’s polling
interrogation stops.
• Alarm LED
Red led flashes to show “alarm” state.
• Designed For High Ambient Temperature Operation
Install in ambient temperatures up to 120 °F (49 °C).
• Flush or Surface Mount
• Optional Markings Available
Glass inserts with multiple languages are available.
• Designed To ISO 9001 Standard
Manufactured to strict international quality standards.
Intelligent Break Glass
Call Point
SIGI-271
Data Sheet 85001-0349 Issue 2
Not to be used for installation purposes. Page of 4
Application
The operating characteristics of the fire alarm Call Point is determined by its sub-type code or “Personality Code”. NORMALLY OPEN
ALARM - LATCHING (Personality Code 1) is assigned by the factory;
no user configuration is required. The device is configured for Class
B IDC operation. An ALARM signal is sent to the loop controller when
the switch is closed (i.e. when the glass is broken). The alarm condition is latched at the station.
Compatibility
Signature Series Call Points are compatible only with Signature Loop
Controller.
Testing & Maintenance
To test the Call Point simply insert the special test key (provided with
every unit); the glass drops and the switch closes. Removing the key
restores the Call Point to normal.
The Call Point’s automatic self-diagnosis identifies when it is defective and causes a trouble message. The user-friendly maintenance
program shows the current state of each Signature Series device
and other pertinent messages. Single devices may be deactivated
temporarily, from the control panel. Availability of some maintenance features is dependent on the fire alarm system used.
Scheduled maintenance (Regular or Selected) for proper system operation should be planned to meet the requirements of the Authority Having Jurisdiction (AHJ).
Installation and Mounting
The Signature Series fire alarm Call Points flush
mount to standard European General Purpose
Outlet Boxes using the KAC ETT/1-P European
Terminal Tray. Surface mounting requires the
KAC SR3T-P Surface Mounting Box. GE Security
recommends that Call Points be installed
according to latest recognized edition
of national and local fire alarm codes.
Electronic Addressing - The Signature
loop controller electronically addresses
each Call Point, saving valuable time
during system commissioning. Setting
complicated switches or dials is not
required. Each Call Point has its own unique serial number stored
in its “on-board memory”. The loop controller identifies each device
on the loop and assigns a “soft” address to each serial number. If
desired, the Call Points can be addressed using the SIGA-PRO Signature Program/Service Tool.
Warnings & Cautions
This device will not operate without electrical power. As fires frequently cause power interruption, we suggest you discuss further
safeguards with your fire protection specialist.
Dimensions
89 mm (3.5 in)
To test the Call Point simply insert the
special test key (provided with every unit);
the glass drops and the switch closes.
Removing the key restores the Call Point
to normal.
32 mm
(1.3 in)
93 mm (3.7 in)
Testing & Maintenance
27.5 mm
(1.1 in)
The Call Point’s automatic self-diagnosis identifies when it is defective
and causes a trouble message.
The user-friendly maintenance
program shows the current state of each Signature Series device
and other pertinent messages. Single devices may be deactivated
temporarily, from the control panel. Availability of some maintenance features is dependent on the fire alarm system used.
Scheduled maintenance (Regular or Selected) for proper system operation should be planned to meet the requirements of the Authority Having Jurisdiction (AHJ).
Data Sheet 85001-0349 Issue 2
Not to be used for installation purposes. Page of 4
Typical Wiring
Specifications
Connecting to the Call Point is made easy, and virtually ‘Plug-in’. The
Call Point is supplied with flying leads and grip forks that connect to
large terminals in the ETT/1 or SR3T mounting accessory. Installer
cables are accommodated in robust ‘clamp type’ terminals that will
each take two conductors in the manner required by BS5839: Part
2. See Signature Loop Controller catalogue sheet for detailed wiring
requirement specifications.
REAR VIEW
Installation
Instructions
of
SIGI-271
CONNECT ONLY IN
ACCORDANCE
WITH ENCLOSED DATA
Addressing Requirements Uses 1 module address
Standby = 250 µA
Operating Current
Activated = 400 µA
Type Code
Factory Set
Operating Voltage
15.2 to 19.95 Vdc (19 Vdc nominal)
Operating Temp.
32 °F to 120 °F (0 °C to 49 °C)
Storage Temp.
-4 °F to 140 °F (-20 °C to 60 °C)
Humidity
0 to 93% RH
On-board RED led: Flashes when in alarm;
LED Operation
Glows steady when in alarm-stand-alone mode
Compatibility
Use with Signature Loop Controller
Call Point Material
Thermoplastic (red)
Agency Listings
CE Compliant
Mounting Hole
(1 Each Side)
DATA IN/OUT (+)
RED
BLACK
DATA IN (-)
From Signature Controller
or Previous Device
B/W
DATA OUT (-)
1
Black Wire
B/W
Wire
Red Wire
Data In (+)
Data Out (+)
Data In (-)
Data Out (-)
KAC ETT1-P Tray Wiring
Data In (+)
Data In (-)
Black
Wire
Data Out (+)
Data Out (-)
Red
Wire
B/W
Wire
KAC SR3T-P Box Wiring
Data Sheet 85001-0349 Issue 2
Not to be used for installation purposes. Page of 4
GE
Security
Ordering Information
U.S.
T 888-378-2329
F 866-503-3996
Canada
T 519 376 2430
F 519 376 7258
Asia
T 852 2907 8108
F 852 2142 5063
Australia
T 61 3 9259 4700
F 61 3 9259 4799
Europe
T 32 2 725 11 20
F 32 2 721 86 13
Model
SIGI-271
Description
Intelligent Call Point - English Markings
Carton
89 x 90 x 35mm
Ship Wt.
150g
Accessories
SR3T-P
ETT/1-P
271-KG1
271-KG1-F005
271-KG1-F1
271-KG1-F2
271-KG1-F200
271-KG1-F3
Surface Mount Box - Red
European Terminal Tray (for flush mounting)
Replacement Glass Pack (5 inserts) - English only
Replacement Glass Pack (5 inserts) - Spanish only
Replacement Glass Pack (5 inserts) - Polish/English
Replacement Glass Pack (5 inserts) - Russian only
Replacement Glass Pack (5 inserts) - Hungarian/English
Replacement Glass Pack (5 inserts) - Arabic/English
89 x 90 x 35mm
89 x 90 x 35mm
82 x 48 x 14mm
82 x 48 x 14mm
82 x 48 x 14mm
82 x 48 x 14mm
82 x 48 x 14mm
82 x 48 x 14mm
50g
47g
70g
70g
70g
70g
70g
70g
Latin America
T 305 593 4301
F 305 593 4300
www.gesecurity.com
© 2006 General Electric Company
All Rights Reserved
imagination at work
Data Sheet 85001-0349 Issue 2
Not to be used for installation purposes. Page of 4
Download PDF

advertising