Avaya 9135 6000 VA
Uninterruptible Power Systems
Site Preparation,
Installation and Operator’s Manual
www.powerware.com/avaya
Avaya 9135 6000 VA
Uninterruptible Power Systems
Site Preparation,
Installation and Operator’s Manual
www.powerware.com/avaya
Requesting a Declaration of Conformity
Units that are labeled with a CE mark comply with the following harmonized standards and EU directives:
S
Harmonized Standards: EN 62040-1-1 and EN 62040-2; IEC 60950-1
S
EU Directives:
73/23/EEC, Council Directive on equipment designed for use within certain voltage limits
93/68/EEC, Amending Directive 73/23/EEC
2004/108/EEC, Council Directive relating to electromagnetic compatibility
The EC Declaration of Conformity is available upon request for products with a CE mark. For copies of the EC
Declaration of Conformity, contact:
Eaton Power Quality Oy
Koskelontie 13
FIN-02920 Espoo
Finland
Phone: +358-9-452 661
Fax: +358-9-452 665 68
Avaya and the Avaya logo are trademarks of Avaya Inc. and may be registered in certain jurisdictions. Eaton and
LanSafe are registered trademarks and ConnectUPS is a trademark of Eaton Corporation or its subsidiaries and
affiliates. Phillips is a registered trademark of Phillips Screw Company. All other trademarks are property of their
respective companies.
ECopyright 2008 Avaya Inc. All rights reserved. No part of this document may be reproduced in any way without
the express written approval of Avaya.
Class A EMC Statements
FCC Part 15
NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
EN 62040-2
Some configurations are classified under EN 62040-2 as “Category C2 UPS.” For these configurations, the
following applies:
WARNING This is a category C2 UPS product. In a residential environment, this product may cause radio
interference, in which case the user may be required to take additional measures.
Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important
information:
RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock
symbol.
CAUTION: REFER TO OPERATOR’S MANUAL - Refer to your operator’s manual for additional
information, such as important operating and maintenance instructions.
This symbol indicates that you should not discard the UPS or the UPS batteries in the trash. This
product contains sealed, lead-acid batteries and must be disposed of properly. For more information,
contact your local recycling/reuse or hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE) in
the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.
Table of Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
Inspecting the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking the Accessory Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the UPS Internal Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rackmount Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Rail Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tower Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RPO Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Upstream Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Required Cable Cross-Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the Power Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
20
22
23
23
24
30
35
37
38
38
38
39
41
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
43
Control Panel Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turning the UPS On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting the UPS on Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turning the UPS Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Eco Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bypass Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Access to Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Access to UPS Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring the UPS for EBMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Running Battery Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
43
44
44
45
45
46
46
46
47
47
48
48
50
51
4
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
i
TABLE OF CONTENTS
Access to Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Life Cycle Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Anticipate Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset or Disable LCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
52
53
53
54
Additional UPS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Relay Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
56
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
59
Hot-Swapping the Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hot-Swapping the Battery Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
59
60
7
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
8
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
63
Troubleshooting LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting Not Requiring Avaya Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting Requiring Avaya Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Obtaining Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
63
64
65
66
66
5
6
ii
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
Chapter 1
Introduction
The Avaya® 9135 uninterruptible power system (UPS) protects
your sensitive electronic equipment from the most common power
problems including power failures, power sags, power surges,
brownouts, line noise, high voltage spikes, frequency variations,
switching transients, and harmonic distortion.
Power outages can occur when you least expect it and power
quality can be erratic. These power problems have the potential to
corrupt critical data, destroy unsaved work sessions, and damage
hardware — causing hours of lost productivity and expensive repairs.
With the Avaya 9135, you can safely eliminate the effects of power
disturbances and guard the integrity of your equipment. Figure 1 shows
the Avaya 9135 UPS.
Figure 1. The Avaya 9135 UPS
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
1
INTRODUCTION
Providing outstanding performance and reliability, the Avaya 9135’s
unique benefits include:
S Online UPS design with pure sine wave output. The UPS filters and
regulates incoming AC power and provides consistent power to your
equipment without draining the battery.
S Two-in-one form factor for using the UPS in a rack-mount
configuration or as a standalone cabinet.
S Hours of extended runtime with up to six EBMs per UPS.
S Start-on-battery capability for powering up the UPS even if utility
power is not available.
S Hot-swappable power module and battery tray that simplify
maintenance by allowing you to replace them safely without
powering down the critical load.
S Shutdown control through the remote power-off (RPO) port.
S Two standard communication options with a USB port and an RS-232
serial port.
S Advanced power management for graceful shutdowns and power
monitoring.
S Network Management Card for increased power protection and
control.
S Backed by worldwide agency approvals.
2
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
Chapter 2
Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that you should follow during installation and
maintenance of the UPS and batteries. Please read all instructions before operating the
equipment and save this manual for future reference.
DANGER
This UPS contains LETHAL VOLTAGES. All repairs and service should be performed by
AUTHORIZED SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS
inside the UPS.
WARNING
S This UPS contains its own energy source (batteries). The UPS output may carry live
voltage even when the UPS is not connected to an AC supply.
S For 208–240V models, the output receptacles may remain electrically live. If the input
power source in your application is wired line-to-neutral (as in most European
applications), the voltage to the output receptacles is 0V. With line-to-line input wiring,
the voltage to the output receptacles is 110–120V (measured from line-to-ground or
line-to-neutral, depending on the UPS wiring).
S Do not remove or unplug the input cord when the UPS is turned on. This removes the
safety ground from the UPS and the equipment connected to the UPS.
S To reduce the risk of fire or electric shock, install this UPS in a temperature and humidity
controlled, indoor environment, free of conductive contaminants. Ambient temperature
must not exceed 40°C (104°F). Do not operate near water or excessive humidity
(95% maximum).
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
3
SAFETY WARNINGS
CAUTION
S Batteries can present a risk of electrical shock or burn from high short-circuit current.
Observe proper precautions. Servicing should be performed by qualified service
personnel knowledgeable of batteries and required precautions. Keep unauthorized
personnel away from batteries.
S Proper disposal of batteries is required. Refer to your local codes for disposal
requirements.
S Never dispose of batteries in a fire. Batteries may explode when exposed to flame.
S Replace batteries with the same number and type of batteries as originally installed in
the UPS.
Sikkerhedsanvisninger
VIGTIGE SIKKERHEDSANVISNINGER
GEM DISSE ANVISNINGER
Denne manual indeholder vigtige instruktioner, som skal følges under installation og
vedligeholdelse af UPS’en og batterierne. Læs venligst alle instruktioner inden betjening af
udstyret og gem denne manual mhp. fremtidige opslag.
FARE
Denne UPS indeholder LIVSFARLIG HØJSPÆNDING. Alle reparationer og vedligeholdelse bør
kun udføres af en AUTORISERET SERVICETEKNIKER. Ingen af UPS’ens indvendige dele kan
repareres af brugeren.
ADVARSEL!
S Denne UPS indeholder sin egen energikilde (batterier). Udgangsstikket på UPS’en kan
endog være strømførende, når UPS’en ikke er koblet til en vekselstrømsforsyning.
S På 208–240V-modeller kan udgangsstikkene være strømførende. Hvis ledningsføringen
til indgangsstrømkilden på din enhed er fase-til-neutral (som på de fleste europæiske
enheder), er spændingen til udgangsstikkene 0V. Med en fase-til-fase
indgangsledningsføring er spændingen til udgangsstikkene 110–120V (målt fra
fase-til-jord eller fase-til-neutral, afhængig af UPS-ledningsføringen).
S Netledningen må ikke fjernes og stikket må ikke trækkes ud, mens UPS’en er tændt.
Dette fjerner sikkerhedsjorden fra UPS’en og fra det udstyr, der er sat til.
S Installér denne UPS i et temperatur- og fugtighedskontrolleret indendørsmiljø, frit for
ledende forureningsstoffer for at formindske risikoen for brand og elektrisk stød.
Rumtemperaturen må ikke overstige 40°C. UPS’en bør ikke betjenes nær vand eller høj
fugtighed (maksimalt 95%).
4
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
SAFETY WARNINGS
ADVARSEL
S Batterierne kan give risiko for elektrisk stød eller brandsår forårsaget af høj
kortslutningsstrøm. Overhold gældende forsigtighedsregler. Servicering skal udføres af
kvalificeret servicepersonale med kendskab til batterier og gældende forsigtighedsregler.
Hold uautoriseret personale væk fra batterierne.
S Korrekt bortskaffelse af batterier er påkrævet. Overhold gældende lokale regler for
bortskaffelsesprocedurer.
S Skaf dig aldrig af med batterierne ved at brænde dem. Batterierne kan eksplodere ved
åben ild.
S Udskift batterierne med samme batterinummer og -type som de oprindeligt installerede i
UPS’en.
Belangrijke Veiligheidsinstructies
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
BEWAAR DEZE INSTRUCTIES
Deze handleiding bevat belangrijke instructies die u dient te volgen tijdens de installatie en
het onderhoud van de UPS en de accu’s. Lees alle instructies voordat u de apparatuur in
bedrijf neemt en bewaar deze handleiding als naslagwerk.
GEVAAR
Deze UPS bevat LEVENSGEVAARLIJKE ELEKTRISCHE SPANNING. Alle reparaties en
onderhoud dienen UITSLUITEND DOOR ERKEND SERVICEPERSONEEL te worden uitgevoerd.
Er bevinden zich GEEN ONDERDELEN in de UPS die DOOR DE GEBRUIKER kunnen worden
GEREPAREERD.
WAARSCHUWING
S Deze UPS bevat een eigen energiebron (accu’s). De UPS-uitgang kan onder spanning
staan, zelfs wanneer de UPS niet is aangesloten op de netspanning.
S Bij de modellen van 208–240 V kan de uitgangscontactdoos onder spanning blijven
staan. Als de bedrading van de ingangsspanningsbron in uw systeem loopt van fase naar
aarde (zoals bij de meeste Europese systemen) dan bedraagt de spanning op de
uitgangscontactdozen 0 V. Als de ingangsbedrading loopt van fase naar fase dan
bedraagt de spanning op de uitgangscontactdozen 110–120 V (gemeten tussen fase en
aarde of tussen fase en neutraal, afhankelijk van de UPS-bedrading).
S Verwijder de ingangsnoer niet of haal de stekker van de ingangsnoer er niet uit terwijl de
UPS aan staat. Hierdoor zou de UPS en uw aangesloten apparatuur geen
aardebeveiliging meer hebben.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
5
SAFETY WARNINGS
S Teneinde de kans op brand of elektrische schok te verminderen dient deze UPS in een
gebouw met temperatuur- en vochtigheidregeling te worden geïnstalleerd, waar geen
geleidende verontreinigingen aanwezig zijn. De omgevingstemperatuur mag 40°C niet
overschrijden. Niet gebruiken in de buurt van water of bij zeer hoge vochtigheid
(max. 95%).
OPGELET
S Batterijen leveren gevaar op voor elektrische schokken en kunnen brandwonden
veroorzaken door een grote kortsluitstroom. Neem de juiste voorzorgsmaatregelen in
acht. Het onderhoud moet worden uitgevoerd door bevoegde onderhoudsmonteurs die
verstand hebben van accu’s en op de hoogte zijn van de vereiste voorzorgsmaatregelen.
Houd onbevoegden uit de buurt van de accu’s.
S De batterijen moeten op de juiste wijze worden opgeruimd. Raadpleeg hiervoor uw
plaatselijke voorschriften.
S Nooit batterijen in het vuur gooien. De batterijen kunnen ontploffen.
S Vervang de accu’s door accu’s met hetzelfde nummer en van hetzelfde type als de
oorspronkelijke accu’s in de UPS.
6
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
SAFETY WARNINGS
Tarkeita Turvaohjeita
TÄRKEITÄ TURVAOHJEITA - SUOMI
SÄILYTÄ NÄMÄ OHJEET
Tämä käyttöohje sisältää tärkeitä ohjeita, joita on noudatettava UPS-virtalähteen ja akkujen
asennuksen ja huollon yhteydessä. Lue kaikki ohjeet ennen laitteiston käyttöä ja säilytä ohje
myöhempää tarvetta varten.
VAARA
Tämä UPS sisältää HENGENVAARALLISIA JÄNNITTEITÄ. Kaikki korjaukset ja huollot on
jätettävä VAIN VALTUUTETUN HUOLTOHENKILÖN TOIMEKSI. UPS ei sisällä MITÄÄN
KÄYTTÄJÄN HUOLLETTAVIA OSIA.
VAROITUS
S Tässä UPS-virtalähteessä on oma energianlähde (akut). UPS-virtalähteen lähdössä voi
olla jännite, vaikka UPS-virtalähdettä ei ole kytketty verkkovirtaan.
S 208–240 V -malleissa lähtövastakkeissa voi säilyä jännite. Jos sovelluksen tulovirtalähde
on johdotettu linjasta neutraaliin (kuten useimmissa eurooppalaisissa sovelluksissa)
lähtövastakkeiden jännite on 0 V. Linjasta linjaan –tulojohdotuksessa lähtövastakkeiden
jännite on 110–120 V (mitataan linjasta maahan tai linjasta neutraaliin, UPS-virtalähteen
johdotuksesta riippuen).
S Älä poista tai irrota sisääntulojohtoa, kun UPS on kytkettynä. Tämä poistaa
turvamaadoituksen UPS-laitteesta ja siihen liitetystä laitteistosta.
S Vähentääksesi tulipalon ja sähköiskun vaaraa asenna tämä UPS sisätiloihin,
joissa lämpötila ja kosteus on säädettävissä ja joissa ei ole virtaa johtavia
epäpuhtauksia. Ympäristön lämpötila ei saa ylittää 40 °C. Älä käytä lähellä vettä ja vältä
kosteita tiloja (95 % maksimi).
VARO
S Akut voivat aiheuttaa sähköiskun tai palovammojen vaaran johtuen suuresta
oikosulkuvirrasta. Noudata kaikkia asianmukaisia varotoimia. Laitteen saa huoltaa vain
ammattitaitoinen huoltohenkilökunta, joka tuntee akut ja niihin liittyvät varotoimet. Älä
päästä valtuuttamatonta henkilöstöä lähelle akkuja.
S Akusto täytyy hävittää säädösten mukaisella tavalla. Noudata paikallisia määräyksiä.
S Älä koskaan heitä akkuja tuleen. Ne voivat räjähtää.
S Vaihda UPS-virtalähteeseen vain samanlaiset akut ja sama määrä akkuja kuin siinä oli
alun perin.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
7
SAFETY WARNINGS
Consignes de sécurité
CONSIGNES DE SÉCURITÉ IMPORTANTES
CONSERVER CES INSTRUCTIONS
Ce manuel comporte des instructions importantes que vous êtes invité à suivre lors de toute
procédure d’installation et de maintenance des batteries et de l’onduleur. Veuillez consulter
entièrement ces instructions avant de faire fonctionner l’équipement et conserver ce manuel
afin de pouvoir vous y reporter ultérieurement.
DANGER!
Cet onduleur contient des TENSIONS MORTELLES. Toute opération d’entretien et de
réparation doit être EXCLUSIVEMENT CONFIÉE A UN PERSONNEL QUALIFIÉ AGRÉÉ.
AUCUNE PIÈCE RÉPARABLE PAR L’UTILISATEUR ne se trouve dans l’onduleur.
AVERTISSEMENT!
S Cette onduleur possède sa propre source d’alimentation (batteries). Il est possible que la
sortie de l’onduleur soit sous tension même lorsque l’onduleur n’est pas connectée à une
alimentation CA.
S En ce qui concerne les modèles 230 V, il est possible que les prises de sortie restent
sous tension. Si la source d’alimentation de votre application est câblée phase et neutre
(comme dans la majorité des applications européennes), la tension vers les prises de
sortie est de 0 V. Avec un câblage d’entrée phase à phase, la tension vers les prises de
sortie est de 115 V (mesurée entre phase et terre ou phase et neutre suivant le câblage
de l’onduleur).
S Ne pas retirer le cordon d’alimentation lorsque l’onduleur est sous tension sous peine de
supprimer la mise à la terre de l’onduleur et du matériel connecté.
S Pour réduire les risques d’incendie et de décharge électrique, installer l’onduleur
uniquement à l’intérieur, dans un lieu dépourvu de matériaux conducteurs, où la
température et l’humidité ambiantes sont contrôlées. La température ambiante ne doit
pas dépasser 40 °C. Ne pas utiliser à proximité d’eau ou dans une atmosphère
excessivement humide (95 % maximum).
8
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
SAFETY WARNINGS
ATTENTION!
S Les batteries peuvent présenter un risque de choc électrique ou de brûlure provenant
d’un courant de court-circuit haute intensité. Observez les précautions appropriées.
L’entretien doit être réalisé par du personnel qualifié connaissant bien les batteries et
les précautions nécessaires. N’autorisez aucun personnel non qualifié à manipuler les
batteries.
S Une mise au rebut réglementaire des batteries est obligatoire. Consulter les règlements
en vigueur dans votre localité.
S Ne jamais jeter les batteries au feu. L’exposition aux flammes risque de les faire
exploser.
S Remplacez les batteries par des batteries du même type et numéro que celles installées
à l’origine sur l’onduleur.
Sicherheitswarnungen
WICHTIGE SICHERHEITSANWEISUNGEN
AUFBEWAREN
Dieses Handbuch enthält wichtige Anweisungen, die Sie während der Installation und
Wartung des USV (Unterbrechungsfreies Stromversorgungssystem) und der Batterien
befolgen müssen. Bitte lesen Sie alle Anweisungen des Handbuches bevor sie mit dem
Gerät arbeiten. Bewaren Sie das Handbuch zum Nachlesen auf.
WARNUNG
Die USV führt lebensgefährliche Spannungen. Alle Reparatur- und Wartungsarbeiten sollten
nur von Kundendienstfachleuten durchgeführt werden. Die USV enthält keine vom Benutzer
zu wartenden Komponenten.
ACHTUNG
S Dieses USV (Unterbrechungsfreies Stromversorgungssystem) enthält eine eigene
Energiequelle (Batterien). Der USV-Ausgang kann Spannung führen, auch wenn das USV
nicht an eine Wechselstromquelle angeschlossen ist.
S Bei Modellen mit 208–240 Volt können die Ausgangssteckverbinder stromführend
bleiben. Wenn die Eingangsstromquelle in Ihrer Anlage mit Masseleitung verkabelt ist
(wie in den meisten europäischen Anlagen), beträgt die Spannung an den
Ausgangssteckverbindern 0 Volt. Bei einer Verkabelung mit Außenleitern beträgt die
Spannung an den Ausgangssteckverbindern 110–120 Volt (gemessen von Leitung zu
Masse oder Leitung zu Masseleiter, abhängig von der UPS (USV)-Verkabelung.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
9
SAFETY WARNINGS
S Das Eingangskabel nicht entfernen oder abziehen, während die USV eingeschaltet ist,
weil hierdurch die Sicherheitserdung von der USV und den daran angeschlossenen
Geräten entfernt wird.
S Um die Brand- oder Elektroschockgefahr zu verringern, diese USV nur in Gebäuden mit
kontrollierter Temperatur und Luftfeuchtigkeit installieren, in denen keine leitenden
Schmutzstoffen vorhanden sind. Die Umgebungstemperatur darf 40°C nicht übersteigen.
Die USV nicht in der Nähe von Wasser oder in extrem hoher Luftfeuchtigkeit (max. 95 %)
betreiben.
VORSICHT!
S Batterien können das Risiko eines elektrischen Schlags bergen oder durch hohen
Kurzschlussstrom in Brand geraten. Die richtigen Vorsichtsmaßnahmen beachten. Die
Wartung muss von qualifiziertem Wartungspersonal durchgeführt werden, das im
Umgang mit Batterien geübt ist und über gute Kenntnisse der erforderlichen
Vorsichtsmaßnahmen verfügt. Nicht autorisiertes Personal von Batterien fern halten.
S Die Batterien müssen ordnungsgemäß entsorgt werden. Hierbei sind die örtlichen
Bestimmungen zu beachten.
S Batterien niemals verbrennen, da sie explodieren können.
S Falls Sie die Batterien austauschen, verwenden Sie bitte ausschließlich die gleiche
Anzahl und die Batterietypen.
10
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
SAFETY WARNINGS
Avvisi di sicurezza
IMPORTANTI ISTRUZIONI DI SICUREZZA
CONSERVARE QUESTE ISTRUZIONI
Il presente manuale contiene importanti istruzioni da seguire durante l’installazione e la
manutenzione dell’UPS e delle batterie. Leggere integralmente le istruzioni prima di
utilizzare l’apparecchiatura e conservare il presente manuale per futuro riferimento.
PERICOLO
La TENSIONE contenuta in questo gruppo statico di continuità è LETALE. Tutte le operazioni
di riparazione e di manutenzione devono essere effettuate ESCLUSIVAMENTE DA
PERSONALE TECNICO AUTORIZZATO. All’interno del gruppo statico di continuità NON vi
sono PARTI RIPARABILI DALL’UTENTE.
AVVERTENZA
S L’UPS contiene la propria fonte di energia (batterie). Le prese d’uscita dell’UPS possono
essere sotto tensione anche quando l’UPS non è collegato all’alimentazione elettrica CA.
S Nei modelli da 230 V è possibile che le prese d’uscita rimangano sotto tensione. Se la
fonte di alimentazione in entrata dell’installazione è costituita da un collegamento
linea-neutro (come accade nella maggior parte delle installazioni europee), la tensione
delle prese d’uscita è pari a 0 V. Con un cablaggio in entrata del tipo linea-linea, la
tensione sulle prese d’uscita è 115 V (con misurazione effettuata da linea a terra o da
linea a neutro in base al cablaggio dell’UPS).
S Non rimuovere nè scollegare il cavo di ingresso quando il gruppo statico di continuità è
acceso poichè in tal modo si disattiverebbe il collegamento a terra di sicurezza del
gruppo statico di continuità e dell’apparecchiatura ad esso collegata.
S Per ridurre il rischio di incendio o di scossa elettrica, installare il gruppo statico di
continuità in un ambiente interno a temperatura ed umidità controllata, privo di agenti
contaminanti conduttivi. La temperatura ambiente non deve superare i 40°C. Non
utilizzare l’unità in prossimità di acqua o in presenza di umidità eccessiva (95% max).
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
11
SAFETY WARNINGS
ATTENZIONE
S Le batterie possono comportare un rischio di scossa elettrica o di ustione in seguito a
un’elevata corrente di corto circuito. Osservare le dovute precauzioni. L’assistenza deve
essere eseguita da personale qualificato esperto di batterie e delle necessarie
precauzioni. Tenere il personale non autorizzato lontano dalle batterie.
S Le batterie devono essere smaltite in modo corretto. Per i requisiti di smaltimento fare
riferimento alle disposizioni locali.
S Non gettare mai le batterie nel fuoco poichè potrebbero esplodere se esposte alle
fiamme.
S Sostituire le batterie con altre dello stesso numero e tipo di quelle originariamente
installate nell’UPS.
12
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
SAFETY WARNINGS
Viktig Sikkerhetsinformasion
VIKTIGE SIKKERHETSINSTRUKSJONER
GJEM DISSE INSTRUKSJONENE
Denne håndboken inneholder viktige instruksjoner som du bør overholde ved montering og
vedlikehold av UPS-enheten og batteriene. Les alle instruksjoner før utstyret tas i bruk, og
gjem håndboken til fremtidig referanse.
FARLIG
Denne UPS’en inneholder LIVSFARLIGE SPENNINGER. All reparasjon og service må kun
utføres av AUTORISERT SERVICEPERSONALE. BRUKERE KAN IKKE UTFØRE SERVICE PÅ
NOEN AV DELENE i UPS’en.
FARLIG
S UPS-enheten inneholder sin egen energikilde (batterier). UPS-utgangen kan være
strømførende selv når UPS-enheten ikke er koblet til et strømuttak.
S Utgangsstikkene kan være strømførende for 208–240 V modellene. Spenningen til
utgangsstikkene vil være 0 V dersom din enhets strømkilde er fase-til-nøytral (som på de
fleste europeiske enheter). Med ledningsført fase-til-fase inngang vil spenningen til
utgangsstikkene være 110–120 V (målt fra fase-til-jord eller fase-til-nøytral, avhenging
av UPS-ledningsføringen).
S For å redusere fare for brann eller elektriske støt, bør denne UPS’en installeres i et
innendørs miljø med kontrollert temperatur og luftfuktighet som er fritt for ledende,
forurensende stoffer. Romtemperaturen må ikke overskride 40°C. Den må ikke brukes i
nærheten av vann eller ved meget høy luftfuktighet (95% maks.).
S For å redusere fare for brann eller elektriske støt, bør denne UPS’en installeres i et
innendørs miljø med kontrollert temperatur og luftfuktighet som er fritt for ledende,
forurensende stoffer. Romtemperaturen må ikke overskride 40°C. Den må ikke brukes i
nærheten av vann eller ved meget høy luftfuktighet (95% maks.).
FORSIKTIG
S Batterier kan utgjøre en fare for elektrisk støt eller brannsår pga. høy kortsluttingsstrøm.
Treff passende forholdsregler. Service bør utføres av kvalifisert servicepersonale med
kjennskap til batterier og nødvendige forholdsregler. Hold uautorisert personale borte fra
batteriene.
S Batterier må fjernes på korrekt måte. Se lokale forskrifter vedrørende krav om fjerning av
batterier.
S Kast aldri batterier i flammer, da de kan eksplodere, hvis de utsettes for åpen ild.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
13
SAFETY WARNINGS
S Skift ut originalbatteriene i UPS-enheten med samme antall og type.
Regulamentos de Segurança
INSTRUÇÕES DE SEGURANÇA IMPORTANTES
GUARDE ESTAS INSTRUÇÕES
Este manual contém instruções importantes que devem ser seguidas durante a instalação e
manutenção do no-break e das baterias. Leia todas as instruções antes de operar o
equipamento e guarde este manual para consultá-lo futuramente.
CUIDADO
A UPS contém VOLTAGEM MORTAL. Todos os reparos e assistência técnica devem ser
executados SOMENTE POR PESSOAL DA ASSISTÊNCIA TÉCNICA AUTORIZADO. Não há
nenhuma PEÇA QUE POSSA SER REPARADA PELO USUÁRIO dentro da UPS.
ADVERTÊNCIA
S Este no-break possui sua própria fonte de energia (baterias). A saída do no-break pode
estar energizada mesmo que este não esteja conectado a uma fonte de energia elétrica.
S Nos modelos 208–240 V, pode ser que as tomadas de saída permaneçam energizadas.
Se a alimentação da sua aplicação for do tipo fase-neutro (como ocorre na maioria das
aplicações na Europa), a tensão das tomadas de saída é de 0 V. Com a alimentação
fase-fase, a tensão das tomadas de saída é de 110–120 V (medida como fase-terra ou
fase-neutro, dependendo da instalação elétrica do no-break).
S Não remova ou desconecte o cabo de entrada quando a UPS estiver ligada. Isto
removerá o aterramento de segurança da UPS e do equipamento conectado.
S Para reduzir o risco de incêndios ou choques elétricos, instale a UPS em ambiente
interno com temperatura e umidade controladas e livres de contaminadores condutíveis.
A temperatura ambiente não deve exceder 40°C. Não opere próximo a água ou em
umidade excessiva (máx: 95%).
PERIGO
S As baterias podem oferecer risco de choque elétrico ou queimadura, ocasionados por
alta tensão com possibilidade de curto-circuito. Tome as precauções adequadas. A
manutenção deve ser realizada por pessoal qualificado, com conhecimento sobre
baterias e ciente das precauções exigidas. Mantenha o pessoal não autorizado afastado
das baterias.
S Siga as instruções apropriadas ao desfazer-se das baterias. Consulte os códigos do local
para maiores informações sobre os regulamentos de descarte de produtos.
14
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
SAFETY WARNINGS
S Nunca jogue as baterias no fogo, porque há risco de explosão.
S Ao realizar a troca das baterias, utilize a mesma quantidade e o mesmo tipo de bateria
instalada originalmente no no-break.
Предупреждения по мерам безопасности
ВАЖНЫЕ УКАЗАНИЯ ПО МЕРАМ БЕЗОПАСНОСТИ
СОХРАНИТЕ ЭТИ УКАЗАНИЯ
В данном руководстве содержатся важные инструкции по установке и
обслуживанию источника бесперебойного питания (ИБП) и батарей. Перед
работой с оборудованием прочтите все инструкции. Сохраните данное
руководство для дальнейшего использования.
ОПАСНО
В данном ИБП имеются СМЕРТЕЛЬНО ОПАСНЫЕ НАПРЯЖЕНИЯ. Все
работы по ремонту и обслуживанию должны выполняться ТОЛЬКО
УПОЛНОМОЧЕННЫМ ОБСЛУЖИВАЮЩИМ ПЕРСОНАЛОМ. Внутри
ИБП нет узлов, ОБСЛУЖИВАЕМЫХ ПОЛЬЗОВАТЕЛЕМ.
ПРЕДУПРЕЖДЕНИЕ
S В данном ИБП установлены собственные источники энергии (батареи). В
ИБП может иметься напряжение даже в том случае, если он не подключен
к сети переменного тока.
S На выходных розетках моделей с напряжением 230 В может быть
напряжение. Если устройство рассчитано на тип подключения
“фаза-нейтраль” (как большинство устройств, изготавливаемых в Европе),
напряжение на выходных розетках равно 0 В. При типе подключения
“фаза-фаза” напряжение на выходных розетках составляет 115 В (при
измерении “фаза-земля” или “фаза-нейтраль”, в зависимости от
электрической схемы ИБП).
S Не отсоединяйте сетевой шнур и не извлекайте его вилку из розетки при
включенном ИБП. При этом защитное заземление отключается от ИБП и
от оборудования, подключенного к ИПБ.
S Для снижения опасности пожара или поражения электрическим током
устанавливайте ИБП в закрытом помещении с контролируемыми
температурой и влажностью, в котором отсутствуют проводящие
загрязняющие вещества. Температура окружающего воздуха не должна
превышать 40°С. Не эксплуатируйте устройство около воды или в местах с
повышенной влажностью (макс. 95%).
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
15
SAFETY WARNINGS
ОСТОРОЖНО
S Высокое напряжение, вызванное коротким замыканием в батарее, может
привести к поражению электрическим током или ожогу. Соблюдайте
меры предосторожности. Техническое обслуживание должно
осуществляться квалифицированным персоналом по работе с
источниками питания, знакомым с мерами предосторожности. Не
допускайте к работе с батареями посторонних.
S Необходимо соблюдать правила утилизации аккумуляторов. Обратитесь к
местным нормативным актам за информацией о требованиях к
утилизации.
S Никогда не бросайте аккумуляторы в огонь. Аккумуляторы могут
взорваться под воздействием огня.
S Заменяйте батареи ИБП только таким же количеством батарей
аналогичного типа.
Advertencias de Seguridad
INSTRUCCIONES DE SEGURIDAD IMPORTANTES
GUARDE ESTAS INSTRUCCIONES
Este manual contiene instrucciones importantes que debe seguir durante la instalación y el
mantenimiento del SIE y de las baterías. Por favor, lea todas las instrucciones antes de
poner en funcionamiento el equipo y guarde este manual para referencia en el futuro.
PELIGRO
Este SIE contiene VOLTAJES MORTALES. Todas las reparaciones y el servicio técnico deben
ser efectuados SOLAMENTE POR PERSONAL DE SERVICIO TÉCNICO AUTORIZADO. No hay
NINGUNA PARTE QUE EL USUARIO PUEDA REPARAR dentro del SIE.
ADVERTENCIA
S Este SIE contiene su propia fuente de energía (baterías). La salida del SIE puede
transportar voltaje activo aun cuando el SIE no esté conectado con una fuente de CA.
S Para los modelos 208–240V, es posible que los receptáculos de salida permanezcan
eléctricamente activos. Si la fuente de energía de entrada de su aplicación está
cableada de línea a neutro (como la mayoría de las aplicaciones europeas), el voltaje a
los receptáculos de salida es 0V. Con cableado de entrada de línea a línea, el voltaje
hacia los receptáculos de salida es 110–120V (medido de línea a tierra o de línea a
neutro, lo que dependerá del cableado del SIE).
S No retire o desenchufe el cable de entrada mientras el SIE se encuentre encendido. Esto
suprime la descarga a tierra de seguridad del SIE y de los equipos conectados al SIE.
16
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
SAFETY WARNINGS
S Para reducir el riesgo de incendio o de choque eléctrico, instale este SIE en un lugar
cubierto, con temperatura y humedad controladas, libre de contaminantes conductores.
La temperatura ambiente no debe exceder los 40°C. No trabaje cerca del agua o con
humedad excesiva (95% máximo).
PRECAUCIÓN
S Las baterías pueden constituir un riesgo de descarga eléctrica o quemaduras por
corriente alta de corto circuito. Adopte las precauciones debidas. Personal calificado de
servicio que conozca de baterías y esté al tanto de las precauciones requeridas debe
darle servicio al equipo. Mantenga al personal no autorizado alejado de las baterías.
S Es necesario desechar las baterías de un modo adecuado. Consulte las normas locales
para conocer los requisitos pertinentes.
S Nunca deseche las baterías en el fuego. Las baterías pueden explotar si se las expone a
la llama.
S Reemplace las baterías con el mismo número y tipo de baterías como se instalaron
originalmente en el SAI.
Säkerhetsföreskrifter
VIKTIGA SÄKERHETSFÖRESKRIFTER
SPARA DESSA FÖRESKRIFTER
Den här anvisningen innehåller viktiga instruktioner som du ska följa under installation och
underhåll av UPS-enheten och batterierna. Läs alla instruktioner innan du använder
utrustningen och spara den här anvisningen för framtida referens.
FARA
Denna UPS-enhet innehåller LIVSFARLIG SPÄNNING. ENDAST AUKTORISERAD
SERVICEPERSONAL får utföra reparationer eller service. Det finns inga delar som
ANVÄNDAREN KAN UTFÖRA SERVICE PÅ inuti UPS-enheten.
VARNING
S Den här UPS-enheten innehåller sin egen energikälla (batterier). UPS-enhetens uttag kan
vara spänningsförande även då UPS-enheten inte är ansluten till spänningsnätet.
S På modellerna 230 V kan de utgående uttagen fortfarande vara strömförande. Om den
ingående strömkällan i din applikation är kopplad ledare-till-nolla (det vanligaste i
Europa) är spänningen till de utgående uttagen 0 V. Är den ingående strömkällan kopplad
ledare-till-ledare är spänningen i de utgående uttagen 115 V (uppmätt från
ledare-till-jord eller ledare-till-nolla beroende på UPS:ens anslutning).
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
17
SAFETY WARNINGS
S Ta aldrig bort nätsladden när UPS-enheten är påslagen. Detta tar bort skyddsjordningen
från både UPS-enheten och den anslutna utrustningen.
S Minska risken för brand eller elektriska stötar genom att installera denna UPS-enhet
inomhus, där temperatur och luftfuktighet är kontrollerade och där inga ledande
föroreningar förekommer. Omgivande temperatur får ej överstiga 40°C. Använd inte
utrustningen nära vatten eller vid hög luftfuktighet (max 95 %).
VIKTIGT
S Batterierna kan innebära en risk för elektrisk stöt eller brännskada från kortsluten
starkström. Iakttag lämpliga försiktighetsåtgärder. Service ska utföras av utbildad
servicepersonal med kunskap om batterierna och nödvändiga försiktighetsåtgärder. Håll
ej behörig personal borta från batterierna.
S Batterierna måste avyttras enligt anvisningarna i lokal lagstiftning.
S Använda batterier får aldrig brännas upp. De kan explodera.
S Byt ut batterierna mot samma antal och typer av batterier som ursprungligen installerats
i UPS-enheten.
18
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
Chapter 3
Installation
This section explains:
S Equipment inspection
S UPS internal battery connection
S UPS setup and installation, including Extended Battery Modules
(EBMs)
S Remote power-off (RPO) installation
S UPS rear panel
Inspecting the Equipment
If any equipment has been damaged during shipment, keep the shipping
cartons and packing materials for the carrier or place of purchase and file
a claim for shipping damage. If you discover damage after acceptance,
file a claim for concealed damage.
To file a claim for shipping damage or concealed damage: 1) File with
the carrier within 15 days of receipt of the equipment; 2) Send a copy of
the damage claim within 15 days to your Avaya service representative.
NOTE Check the battery recharge date on the shipping carton label. If the date has expired
and the batteries were never recharged, do not use the UPS. Contact your Avaya service
representative.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
19
INSTALLATION
Checking the Accessory Kit
NOTE Packaging must be destroyed according to waste management standards. Recycling
icons are displayed for easy selection.
Verify that the following additional items are included with the UPS:
Table 1. UPS Accessory Kit
Item
Description
UPS user’s guide or CD
Screwdriver
RS-232 serial cable
Rackmounting kit for 19-inch (48 cm) bays
Two sets of pedestals with screws for tower position
20
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
INSTALLATION
If you ordered an optional EBM, verify that the following items are
included with the EBM:
Table 2. EBM Accessory Items
Item
Description
EBM user’s guide
EBM cable
EBM communication cable
Rackmounting kit for 19-inch (48 cm) bays
Pedestal extenders for tower position
Joining bracket and screws for tower position
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
21
INSTALLATION
Connecting the UPS Internal Battery
To ensure proper battery operation:
1.
Verify that the UPS is off and unplugged.
2.
Remove the two screws from the battery switch (see Figure 2).
Two
Screws
Battery Switch
Figure 2. Removing the Battery Switch Screws
3.
Slide the battery connector so that you can read Connected (see
Figure 3).
4.
Reinstall the two screws removed in Step 2.
Figure 3. Connecting the Internal Battery Connector
22
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
INSTALLATION
UPS Setup
The Avaya 9135 UPS is designed for flexible configurations and can be
installed in a rack or as a standalone cabinet.
If you are installing the UPS in a rack, continue to the following section,
“Rackmount Setup;” otherwise, continue to “Tower Setup” on page 30.
Rackmount Setup
The rail kit can be mounted in 19-inch panel (48 cm) racks from 24 to
30 inches (61 to 76 cm) deep and includes:
S Left and right sliding rail assemblies
S (20) M4×6 mm Phillips® flat-head screws
S (4) M4×10 mm Phillips round-head screws
S (4) M6×12 mm Phillips round-head screws
S (8) M6×12 mm Phillips flat-head screws
S (2) mounting brackets
S (2) rear hold-down brackets
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
23
INSTALLATION
Installing the Rail Kit
CAUTION
S DO NOT install the UPS or EBM in a hermetically-closed environment without any
exchange of air.
S The UPS and EBM are heavy (see page 61): 1) Avaya strongly recommends to remove the
battery tray from the UPS before lifting. 2) A minimum of two people are required to lift
the cabinets into the rack.
NOTE The rails and the necessary mounting hardware are supplied by Avaya.
To install the rail kit:
1.
Adjust the UPS control panel orientation by slightly pulling out the
control panel and rotating it 90° counterclockwise (see Figure 4).
Figure 4. Adjusting the UPS Control Panel Orientation
24
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
INSTALLATION
2.
Recommended. Remove the UPS battery tray (see Figure 5):
S Remove the UPS front cover (six screws).
NOTE A ribbon cable connects the control panel to the UPS. Do not pull on the cable or
disconnect it.
S Place the front panel above the UPS.
S Remove the two battery retaining brackets (four screws).
S Slightly pull the battery tray, then lift it to extract it.
Figure 5. Removing the Battery Tray
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
25
INSTALLATION
3.
Place the cabinet on a flat, stable surface with the front of the
cabinet facing you.
NOTE You can adjust the position of the mounting brackets.
4.
Align the mounting brackets with the screw holes on the side of the
cabinet and secure with the supplied M4×6 mm flat-head screws.
5.
If installing additional cabinets, repeat Steps 3 and 4 for each
cabinet.
Figure 6. Installing the Mounting Brackets
26
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
INSTALLATION
6.
Loosen the assembly wing nuts on both rail assemblies and adjust
the rail size for the depth of your rack (see Figure 7).
7.
Select the proper holes in the rail for positioning the UPS in the
desired location in the rack.
8.
Using two M6×12 mm flat-head screws, attach the rail to the rear
of the rack.
9.
Secure the rail to the front of the rack with two M6×12 mm
screws.
10. Repeat Steps 8 and 9 for the other rail.
Figure 7. Installing the Rails
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
27
INSTALLATION
11. Optional. Install the rear hold-down brackets (included with the rail
kit) if you need to move the rack enclosure with the UPS already
rack-mounted inside (see Figure 8).
Figure 8. Installing the Rear Hold-Down Brackets
12. Slide the UPS and any optional EBMs into the rack.
13. Secure the front of the cabinet to the rack using two M6×12 mm
round-head screws on each side (see Figure 9).
Figure 9. Installing the Cabinets
28
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
INSTALLATION
14. Optional. If you installed the rear hold-down brackets, secure the
brackets to the rear rails using two screws for each bracket (see
Figure 10).
Figure 10. Securing the Rear Hold-Down Brackets
15. If you removed the UPS battery tray in Step 2, replace the battery
tray and secure with the battery retaining brackets.
Replace the UPS front cover.
16. Continue to “Installing the UPS” on page 35.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
29
INSTALLATION
Tower Setup
CAUTION
S DO NOT install the UPS or EBM in a hermetically-closed environment without any
exchange of air.
S The UPS and EBM are heavy (see page 61). A minimum of two people are required to lift
the cabinets into the pedestals.
The setup varies depending on the number of cabinets you are installing:
1.
Assemble the UPS pedestals (see Figure 11).
Figure 11. Assembling the UPS Pedestals
2.
For one cabinet, the pedestals must be installed. Continue to Step 3.
For two or more cabinets, the pedestal extenders and the joining
brackets must be installed. Proceed to Step 6.
NOTE Always keep 150 mm free space behind the UPS rear panel. The distance between
the tower stands should be 450 mm.
30
3.
Carefully position the cabinet upright with the UPS indicators at the
top and place in the pedestals (see Figure 12).
4.
Adjust the pedestals to the size of the UPS and secure the
pedestals with the captive screws.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
INSTALLATION
UPS Indicators
150 mm
(6”)
450 mm
(17.7”)
Figure 12. Tower Position with One Cabinet
5.
Continue to “Installing the UPS” on page 35.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
31
INSTALLATION
6.
Install pedestal extenders for each additional cabinet:
For two cabinets, insert the extender into position 3 on the pedestal
(see Figure 13).
For three cabinets or more, insert the extender into position 4 on
the pedestal (see Figure 14).
4
1 23
4
1 23
Figure 13. Extending the Pedestals for Two Cabinets
4
123
4
123
4
123
Figure 14. Extending the Pedestals for Three or More Cabinets
32
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
INSTALLATION
7.
Carefully position the cabinet upright with the UPS indicators at the
top and place in the pedestals (see Figure 15).
8.
Adjust the pedestals to the size of the UPS and secure the
pedestals with the captive screws.
Figure 15. Tower Position with Two Cabinets
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
33
INSTALLATION
9.
Align each joining bracket with the adjacent cabinet screw holes
and secure with the supplied screws (see Figure 16).
NOTE Joining brackets are required for installations with two or more cabinets.
Joining Bracket
Figure 16. Installing the Joining Brackets
10. If installing additional EBMs, repeat Step 6 for each cabinet.
11. Continue to the following section, “Installing the UPS.”
34
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
INSTALLATION
Installing the UPS
NOTE Do not make unauthorized changes to the UPS or accessories; otherwise, damage
may occur to your equipment and void your warranty.
See “UPS Rear Panels” on page 41 for the rear panel of each model.
To install the UPS and optional EBMs:
1.
If installing an optional EBM, continue to Step 2; otherwise,
continue to Step 6.
2.
Verify that the EBM battery circuit breaker is OFF.
3.
Plug the EBM cable into the battery connector (see Figure 17).
Up to six EBMs may be connected to the UPS.
4.
For one to four EBMs. Plug the EBM communication cable into the
RJ-11 port.
NOTE If there are five or more EBMs, do not connect the EBM communication cable.
5.
See “Configuring the UPS for EBMs” on page 50 to set the number
of installed EBMs.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
35
INSTALLATION
EBM Cable
EBM
Communication
Cable
Battery Circuit
Breaker
EBM Battery
Connectors
Figure 17. UPS Installation with Three EBMs
36
6.
If you are installing a remote power-off (RPO) switch, see the
following section, “RPO Installation,” to install the switch before
powering on the UPS.
7.
Continue to “UPS Electrical Connections” on page 38.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
INSTALLATION
RPO Installation
Installation of the RPO function must be carried out in compliance with
applicable regulations. The cable is not included.
In order to fully de-energize devices and the Avaya 9135 with the RPO
port, it is necessary to:
S Use a two-position switch (normally-open or normally-closed contact
and held more than one second).
S Connect this RPO switch to a device that trips all breaker(s) located
upstream(1) and downstream(2) the Avaya 9135 UPS. This can be
achieved by means of a shunt trip:
- (1) If not, the output devices could be powered again through static
switch when the two-position switch is released.
- (2) If not, the output devices will remain powered several seconds
after the RPO activation.
NOTE The internal batteries will remain connected to the power module after RPO
activation.
RPO Contact Normally-Open
RPO Contact Normally-Closed
RJ-12 (6p6c)
RJ-12 (6p6c)
5 Vdc to 27 Vdc
5 Vdc to 27 Vdc
Figure 18. RPO Communication Port
S Signal:
- Activation voltage: 5 Vdc to 27 Vdc
- Current: 10 mA maximum
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
37
INSTALLATION
UPS Electrical Connections
WARNING
Only qualified service personnel (such as a licensed electrician) shall perform the electrical
installation. Risk of electrical shock.
CAUTION
S For UPS models with hardwired outputs, overcurrent protection for the output AC
circuit(s) is to be provided by others.
S For UPS models with hardwired outputs, suitably rated disconnect switches for the
output AC circuit(s) are to be provided by others.
Recommended Upstream Protection
The indicated protection ensures discrimination for each output circuit
downstream of the UPS.
If these recommendations are not followed, protection discrimination is
not achieved and may result in a potential power interruption to the
connected devices.
UPS Power Rating
Upstream Circuit Breaker
6000 VA
D curve - 35A
2 Poles Circuit Breaker
L (L1)
N (L2)
G
To Utility Source
N L
(L2) (L1)
Figure 19. Recommended Upstream Protection
Required Cable Cross-Sections
Function
Terminal block cable capacity
Capacity for ground/earthing conductor
38
Wiring
6 mm2, solid or stranded wire
(maximum 8 mm2 or 10 AWG).
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
INSTALLATION
Connecting the Power Cables
WARNING
S Only qualified service personnel (such as a licensed electrician) shall perform the
electrical connection. Risk of electrical shock.
S Before carrying out any connection, check that the battery circuit breaker and upstream
protection device (utility input) are OFF (O).
S Use included insulated ferrules with stranded wires.
Remove the terminal block cover (two screws) with the supplied
screwdriver (see Figure 20).
RS-2-23
BATT
.O
N
. RPO
1.
24A
5
-2-0V~,
200
Output Cable
Opening
T
N:
C
E
N
IO
N
TID
O
C
U
S
LE
AE
B
TY
A
O
C
C
N
D
O
R
D
O
T
T
LA
A
R
B
E
D
N
R
RY
O
E
T
TT
dcU
A
E
V
D
B
N
N
80
1C
O
C
Input Cable
Figure 20. Removing the Terminal Block
2.
Connect the three wires to the input terminal block.
CAUTION
Always connect the ground/earthing wire first.
3.
Insert the output cable through the output cable opening.
4.
Connect the three wires to the output terminal block.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
39
INSTALLATION
Output Terminal
GND L2
(N)
L1
Input Terminal
GND L2
(N)
L1
Figure 21. Installing the Input and Output Cables
5.
Replace the terminal block cover and tighten the cables.
6.
Secure the terminal block cover with the two screws removed in
Step 1.
7.
Plug the equipment to be protected into the appropriate UPS output
receptacles.
NOTE If more than one load is connected to the UPS, the total capacity of the loads should
not exceed 30A.
Figure 22. Connecting the Power Cords
40
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
INSTALLATION
UPS Rear Panel
Figure 23 shows the 6000 VA Avaya 9135 UPS rear panel.
(4) L6-30 Receptacles
200--250V~,24A
Output Terminal Block
Input Cord with L6-30P
EBM Battery Connector
BATTERY DO NOT DISCONNECT
CONNECTOR
BATTERY CABLE
180VDdc
UNDER LOAD
CAUTION:
Network Management Card
USB Port
Relay Port
RPO Port
RS-232 Port
RS--232
BATT. NO.
RPO
EBM RJ-11 Connector
Figure 23. 6000 VA
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
41
INSTALLATION
42
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
Chapter 4
Operation
This section describes:
S The control panel
S Turning the UPS on and off
S Starting the UPS on battery
S Operating modes
S Display functions
Control Panel Functions
The UPS has a four-button graphical LCD with backlight. It provides
useful information about the UPS itself, load status, events,
measurements, and settings (see Figure 24).
Bypass Indicator
Alarm Indicator
Battery Indicator
Power Indicator
esc
Escape
Up
Down
Enter
On/Off Button
Figure 24. UPS Control Panel
NOTE The On/Off button controls only the UPS output. The On/Off button has no effect on
equipment connected to the UPS.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
43
OPERATION
Turning the UPS On
To turn the UPS on:
1.
Verify that the UPS internal battery connector is connected (see
Figure 2 on page 22).
2.
Set the upstream circuit breaker (not included) to the ON position.
The equipment is powered by utility power, but not protected by
the UPS.
Batteries are recharging. An eight-hour recharge period is necessary
to get full backup time.
The
and
indicators illuminate.
To change the factory-set defaults, see “User Settings ” on
page 48.
3.
button until you hear the UPS beep
Press and hold the
(approximately three seconds).
After the UPS is turned on, it conducts a self-test and enters
indicator remains on and the
indicator
Normal mode. The
turns off indicating that power is available to your equipment.
If the alarm beeps or a UPS alarm indicator stays on, see
“Troubleshooting” on page 63.
Starting the UPS on Battery
NOTE Before using this feature, the UPS ON/OFF settings must have been enabled (see
Table 5 on page 49).
To turn on the UPS without using utility power, press and hold the
button for three seconds. The UPS starts up in Battery mode and
supplies battery power to your equipment.
44
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
OPERATION
Turning the UPS Off
To shut down the UPS:
1.
Press the
button for approximately three seconds
The UPS beeps once, and the load is no longer protected by the
UPS. It is powered by utility power. If the UPS is set in frequency
converter mode, the equipment will not be powered.
If the utility power is out of tolerance, the UPS will generate a
10 ms output calibrated break.
2.
For a full shutdown of UPS and connected load, the upstream
circuit breaker (not included) should be set to the OFF position.
Operating Modes
The Avaya 9135 front panel indicates the UPS status through the UPS
indicators. Figure 25 shows the UPS front panel indicators and controls.
On Battery Indicator
Power On Indicator
Bypass Indicator
Alarm Indicator
Indicator Legend
Unlit
Lit
Flashing
esc
On/Off Button
Figure 25. UPS Front Panel
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
45
OPERATION
Normal Mode
During Normal mode, the
indicator illuminates. The UPS monitors
and charges the batteries as needed and provides power protection to
your equipment.
Eco Mode
During Eco mode, the
indicator illuminates. Eco mode reduces the
consumption of electrical power.
Under normal conditions (utility power available), the equipment is
supplied in ECO mode.
NOTE ECO mode: operating mode by which the equipment is supplied directly by the utility
power if it is within the tolerances defined by the user.
If utility power is out of tolerance, the
indicator flashes and the
indicator illuminates. The equipment is protected by the UPS.
Battery Mode
When the UPS is operating during a power outage, the alarm beeps
and
indicators illuminate. The
once every five seconds and the
equipment is protected by the UPS and supplied by the battery. The
display shows the remaining battery backup time.
If battery capacity becomes low while in Battery mode, the alarm beeps
every five seconds. Immediately complete and save your work to
prevent data loss and similar difficulties.
When the utility power returns, the UPS transfers to Normal mode
operation while the battery recharges.
End of backup time: all indicators turn off. The alarm beeps continuously
and the UPS displays End of backup time Battery low.
When utility power is restored after the UPS shuts down, the UPS
automatically restarts.
46
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
OPERATION
Bypass Mode
The UPS transfers to Bypass mode when:
S The utility power is out of tolerance
S There is an overload condition
S The
button is pressed
S There is a malfunction
The
and
utility power.
indicators illuminate and the equipment is powered by
Display Functions
Figure 26 shows the basic menu structure.
Status and Alarms
Measurements
UPS Input Measurements
UPS Output Measurements
Battery Measurements
UPS Setup
Local Settings
Output Settings
ON/OFF Settings
Battery Settings
Maintenance
Model
Alarm History
Manual Batt Test
LED & Buzzer Test
LCM
Statistics
Figure 26. Menu Map for Display Functions
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
47
OPERATION
Access to Measurements
Press the button on the UPS front panel to access measurements for
voltage, current, frequency, power output, and battery capacity.
Access to UPS Setup
To access the UPS Setup menu:
1.
Scroll to the UPS Setup menu by pressing the
2.
Press the
button.
button to get access.
esc
Figure 27. Access to UPS Setup
The following tables display the options that can be changed by the
user.
Table 3. Local Settings
Function
Factory Setting
Options
Language
English
French, German, Italian, Portuguese, Spanish
Date / Time Format
International
(DD-MM-YYYY/HH :MM)
US (MM-DD-YYYY/HH:MM AM/PM)
Date / Time Change
GMT + 1
(Continental Europe)
MM-DD-YYYY/HH :MM adjustable
Audible Alarm
Yes
No
48
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
OPERATION
Table 4. Output Settings
Function
Factory Setting
Options
Comments
Output Voltage
208V
200V / 208V / 220V /
240V / 250V
Freq Converter
Disable
Enable
Output Frequency
60 Hz
60 Hz
User selectable under
frequency-converter mode
Eco Mode
Disable
Enable
See page 46
Slew Rate
1 Hz / sec
0.5 Hz / sec
Bypass Transfer
If bypass Ac nok?
Yes
No
Transfer to bypass if utility power is
out of tolerance
Interrupt Time
10 ms
20 ms, ...... , 200 ms
Break time calibration during load
transfer on utility power out of
tolerance
Overload Prealarm
105%
40%, 50%, 70%
Alarm if threshold is overrun
Function
Factory Setting
Options
Comments
Cold Start
Disable
Enable
Start on battery
Forced Reboot
Enable
Auto Restart
Enable
Disable
UPS restarts automatically when
utility power is restored
Energy Saving
Disable
Enable
Automatic shutdown on battery if
output load level <10%
Sleep Mode
Enable
Disable
Remote Command
Enable
Disable
Table 5. ON/OFF Settings
Enables automatic restart of the
system even if utility power is
restored before the end of the
shutdown sequence
Enables consideration of shutdown or
restart orders from software to be
authorized
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
49
OPERATION
Table 6. Battery Settings
Function
Factory Setting
Options
Comments
Auto Battery Test
Everyweek
No test / everyday /
everyweek /everymonth
Low Batt Warning
20%
0 to 100%
1% increment
User Batt Settings
UPS reads number of
battery modules
connected
From 0 to 95 Ah
5 Ah increment
Deep Disch Protect
Yes
No
Protection against deep discharge.
If disabled, the Avaya warranty will
be void.
Configuring the UPS for EBMs
NOTE The UPS automatically configures up to four EBMs with the EBM communication
cable installed. Use the following steps for installations with five or more EBMs.
To ensure maximum battery runtime for installations with five or more
EBMs, configure the UPS for the correct number of EBMs:
50
button.
1.
Scroll to the UPS Setup menu by pressing the
2.
Press the
3.
Use the button to select the Battery Settings menu and press the
button.
4.
Use the button to select the User Batt Settings option and press
button.
the
button to get access.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
OPERATION
5.
Select the number of ampere hours according to your UPS
configuration:
Configuration
Ah
UPS only (internal batteries)*
5 (default)
UPS + 1 EBM*
15
UPS + 2 EBMs*
25
UPS + 3 EBMs*
35
UPS + 4 EBMs*
45
UPS + 5 EBMs
55
UPS + 6 EBMs
65
* The UPS automatically configures up to four EBMs with the EBM
communication cable installed (see page 35).
6.
Press the
button to save the setting.
7.
Press the esc button until the status screen appears.
Running Battery Tests
Automatic battery tests run every week, unless modified through the
UPS User Settings menu (see Table 6). You can change the automatic
battery test to run every day, every month, or not at all.
For an automatic battery test to run:
S The “Auto Battery Test” setting must be enabled.
S The UPS must be in Normal mode.
S The bypass voltage must be greater than 195V.
During the test, the UPS transfers to Battery mode and discharges the
batteries under the existing load. If the battery voltage drops below
195V during a battery test, the UPS returns to Normal mode. A new test
cannot be started until the battery voltage returns to greater than 195V.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
51
OPERATION
Access to Maintenance
To access the Maintenance menu:
1.
Scroll to the Maintenance menu by pressing the
2.
Press the
button.
button to get access.
esc
Figure 28. Access to Maintenance
The following table displays the maintenance options.
Table 7. Maintenance Settings
Function
Sub-Function
Option/Display
Comments
Model
Power Module
SN: xxxxxxxxx
SOFT: xxx
Serial number
Soft version
Read
Description
Date Hour
Alarm xxx
10 alarms can be stored automatically
Erase
No / Yes
Manual Batt Test
Manual Battery Test
No / Yes
Led & Buzzer Test
Led & Buzzer Test
No / Yes
Life Cycle Monitoring
LCM
Enable / Disable
Statistics
Auto Statistics
Statistics
Custom Statistics
Reset Date ?
Are you sure ?
Frame
Alarm History
52
Life cycling monitoring alarms
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
OPERATION
Life Cycle Monitoring
LCM displays messages on the UPS front panel and through the
communication channels, at every important stage of the UPS’s life.
button to display LCM warning details.
Press the
esc
Figure 29. LCM Warning Screen
Anticipate Maintenance
Automatic warnings appear when maintenance actions need to be
planned:
Table 8. LCM Warning Details
LCM Warning Details
Signification
BATTERY CHECK RECOMMENDED
Battery is approaching its reliability end of life.
Risk to reduce dramatically backup time.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
53
OPERATION
Reset or Disable LCM
In case of any LCM messages displayed:
S For temporary reset: press the esc button for at least three seconds
while in the Status and Alarm menu to temporarily cancel the alarm
status.
The alert will be repeated twice every 30 days.
S For permanent reset: press the
button for at least three seconds
while in the LCM warning menu to permanently cancel the LCM
event.
At any time:
S To disable all LCM messages, select disable all while in the LCM
menu.
Be careful: if you disable all LCM messages, you will not be aware of
any LCM events that can happen on the UPS.
54
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
Chapter 5
Additional UPS Features
The Avaya 9135 provides three communication methods that can be
used simultaneously:
S RS-232 or USB communication. Compatible with most power
management software applications. Note that both ports cannot be
used at the same time.
S The relay port uses output contacts for basic signaling or for
protection of IT systems.
USB Port
The UPS can communicate with a USB-compliant computer using
LanSafe® Power Management Software or other HID-compliant power
management software compatible with Microsoft® Windows® 2000 and
XP operating systems that support HID devices.
NOTE The latest versions of the LanSafe Power Management Software and the USB
firmware are available at www.powerware.com.
To establish communication between the UPS and a computer:
1.
The USB port is hot-pluggable. Connect the USB cable to the USB
port on the UPS rear panel (see Figure 30).
Connect the other end of the USB cable to the USB port on your
computer.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
55
ADDITIONAL UPS FEATURES
200--250V~,24A
CAUTION:
BATTERY
DO NOT DISCONNECT
CONNECTOR
BATTERY CABLE
180VDdc
UNDER LOAD
USB Port
RS--232
BATT. NO.
RPO
Figure 30. The USB Port
2.
Install the LanSafe Power Management Software and USB drivers
according to the instructions provided at www.powerware.com.
Relay Port
When the status is active, the contact between the common (Pin 5) and
the relevant information pin is closed.
Output relays specifications:
S Voltage: 48 Vdc maximum
S Current: 2A maximum
S Power: 62.5 VA, 30W
Example: for 48 Vdc, Imax=625 mA
56
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
ADDITIONAL UPS FEATURES
Figure 31 identifies the cable pins and Table 9 describes the pin
functions.
5
4
9
NC
NO
3 2
8
7
1
6
NO
NO
NO
Common
NOTE Normally-open (NO)
Normally-closed (NC)
Figure 31. Communication Port
Table 9. Communication Port Pin Assignment
Pin Number
Function
1, 2
Not used
3
Remote power-off (RPO) signal (5–27 Vdc, 10 mA max)
4
Operation on mains (not on battery)
5
User common
6
Operation on automatic bypass
7
Low Battery
8
Load protected
9
Operation on battery
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
57
ADDITIONAL UPS FEATURES
58
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
Chapter 6
Maintenance
This section describes replacing the power module and battery tray.
Hot-Swapping the Power Module
WARNING
Only qualified service personnel (such as a licensed electrician) shall perform the electrical
installation. Risk of electrical shock.
This operation can be performed without interrupting the equipment.
1.
Remove the UPS front cover (six screws). See Figure 32.
NOTE A ribbon cable connects the control panel to the UPS. Do not pull on the cable or
disconnect it.
2.
Place the front panel above the UPS.
3.
Remove the two power module brackets (four screws).
4.
Slightly pull the power module, then lift it to extract it.
Figure 32. Removing the Power Module
5.
Replace the faulty power module with one of the same power
rating (6000 VA) and secure with the power module brackets.
6.
Replace the UPS front cover.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
59
MAINTENANCE
Hot-Swapping the Battery Tray
CAUTION
S Batteries can present a risk of electrical shock or burn from high short-circuit current.
Observe proper precautions. Servicing should be performed by qualified service
personnel knowledgeable of batteries and required precautions. Keep unauthorized
personnel away from batteries.
S Remove watches, rings, bracelets and all other metal objects from the hands and arms.
S Use tools with an insulated handle.
S When replacing batteries, replace with the same number of the BB/HR5.5-12 batteries.
This operation can be performed without interrupting the equipment.
1.
Remove the UPS front cover (six screws). See Figure 33.
NOTE A ribbon cable connects the control panel to the UPS. Do not pull on the cable or
disconnect it.
2.
Place the front panel above the UPS.
3.
Remove the two battery retaining brackets (four screws).
4.
Slightly pull the battery tray, then lift it to extract it.
Figure 33. Removing the Battery Tray
5.
Replace the battery tray and secure with the battery retaining
brackets.
NOTE To ensure safety and high performance, use only batteries supplied by Avaya.
6.
60
Replace the UPS front cover.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
Chapter 7
Specifications
Table 10. Input and Output Specifications
Model Number
Power Levels
(Rated at
Nominal Inputs)
700465446
6000 VA, 4200W
Output on
Battery Power
AC Input
Nominal
Voltage
Voltage
Range1
Frequency
Range2
Voltage3
Frequency
208V
156–280V
40–70 Hz
(± 0.2 Hz)
208V
60 Hz
1 The high and low thresholds can be adjusted using the UPS front panel (see page 48).
2 Up to 40 Hz in low-sensitivity mode (programmable using the UPS front panel (see page 48).
3 Adjustable to 200V (10% derating of output power) 208/220/230/240/250V.
Table 11. Dimensions and Weights
Model
Dimensions (WxHxD)
Weight
6000 VA UPS
444.5×130.6×741 mm
(17.5”×5.1”×29.2”)
57 kg (125.7 lb)
UPS Power Module
198×127×603 mm
(7.8”×5”×23.7”)
12 kg (26.5 lb)
UPS Internal Battery
214.5×116×498 mm
(8.4”×4.6”×19.6”)
30.5 kg (67.2 lb)
EBM
444.5×130.6×650 mm
(17.5”×5.1”×25.6”)
70.5 kg (155.4 lb)
Table 12. Power Connections
Model
Input Connection
Output Receptacles
6000 VA
10 ft, L6-30P power cord
(4) NEMA L6-30R
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
61
SPECIFICATIONS
Table 13. Environmental and Safety
Operating Temperature
0°C to 40°C (32°F to 104°F)
Storage Temperature
-25°C to 40°C (-13°F to 104°F)
Relative Humidity
5–95% noncondensing
Operating Altitude
Up to 1,000 meters above sea level
Audible Noise
Less than 46 dBA Normal mode, typical load and Battery mode
Surge Suppression
ANSI C62.41 Category B, IEC 61000-4-5
Safety Conformance
UL 1778;
CSA C22.2, No. 107.1;
NOM-019-SCFI
Agency Markings
cUL, NOM
EMC (Class A)
FCC Part 15
Table 14. Battery
UPS Configuration
(15) 12V, 5.5 Ah internal batteries
EBM Configuration
(2 strings of 15) 12V, 5.5 Ah internal batteries
Type
Sealed, maintenance-free, lead-acid
Recharge Time (to 90%)
Internal batteries: 6 hours
1 EBM: 5 hours; 2 EBMs: 8 hours; 3 EBMs: 13 hours; 4 EBMs: 17 hours
Table 15. Battery Runtimes
UPS
6000 VA
UPS Internal Batteries
+1 EBM
+2 EBMs
+3 EBMs
+4 EBMs
4 min
17 min
33 min
50 min
1 hr 7 min
NOTE Battery times are approximate and vary depending on the load configuration and battery charge.
62
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
Chapter 8
Troubleshooting
This section explains:
S UPS alarms and conditions
S Service and support
Troubleshooting LED
Press the esc button to stop the audible alarm.
NOTE In case of ”MULTIPLE FAULT”, press the
to further details.
button and the
button to get access
NOTE In case of ”LCM WARNING”, see “Life Cycle Monitoring” on page 53.
esc
Escape
Up
Down
Enter
Figure 34. Troubleshooting LED
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
63
TROUBLESHOOTING
Troubleshooting Not Requiring Avaya Service
esc
Figure 35. Environment Fault
Press the
button to display the following details:
Displayed Details
Signification
Correction
NO BATTERY
The battery is incorrectly connected.
Check battery connections.
I/O BAD CONNECTION
Utility input is not connected to the correct
terminals.
Check AC wiring.
NO POWER MODULE
The power module is not inserted.
Check power module connections (see
page 59).
NO BATTERY MODULE
The battery tray is incorrectly connected.
Check battery connections (see page 60).
INV THERM OVERLOAD
The UPS shuts down automatically because
of a major overload.
Check the power drawn by the connected
devices and disconnect any non-priority
devices.
INVERT LIMITATION
Short circuit conditions on output devices.
Check the installation at the UPS output
(wiring, fault equipment).
64
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
TROUBLESHOOTING
Troubleshooting Requiring Avaya Service
NOTE In case of multiple fault, press the
further details.
button and the
button to get access to
esc
Escape
Up
Down
Enter
Figure 36. Troubleshooting LED
Display
Signification
Correction
POWER MODULE FAULT
Internal power module fault detected. Use
”Enter” button to display details.
In Parallel: see the note below to start the
other UPS alone.
Call the Help Desk. Replace the power
module (see page 59).
BATT MODULE FAULT
Battery fault detected during the battery
test. Use ”Enter” button to display details.
Call the Help Desk. Replace the battery tray
(see page 60).
FRAME FAULT
Internal chassis fault detected. Use ”Enter”
button to display details.
Call the Help Desk.
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
65
TROUBLESHOOTING
Obtaining Service
The troubleshooting chart covers most of the difficulties you may
encounter during normal operations. If you have any questions or
problems with your UPS, call your Avaya service representative or the
appropriate telephone number on the service label of your UPS.
Please have the following information ready when you call:
S Material code
S Serial number
S Version number (if available)
S Date of failure or problem
S Symptoms of failure or problem
S Customer return address and contact information
Parts List
SAP Code
Description
700465446
6000 VA, 120V UPS Module, Avaya 9135
700465495
Extended Battery Module for the 6000 VA Avaya 9135
66
Avaya 9135 6000 VA UPS Site Preparation, Installation and Operator’s Manual S 164201769 Rev 1
340-08710 AA
*1642017691*
164201769 1
Download PDF