KLV-V40A10 Installing the Wall-Mount Bracket

KLV-V40A10
Installing the Wall-Mount Bracket
GB
CT
AR
© 2005 Sony Corporation
2-649-439-12(1)
English
Before installation
To Customers
For product protection and safety reasons, Sony
strongly recommends that wall-mounting of your
Display Unit be performed by a reliable licensed
contractor. Do not attempt to install it yourself.
Your KLV-V40A10 can be wall-mounted using
SU-PW2 Wall-Mount Bracket (sold separately).
Please provide your contractor with this
installation supplement as well as the Instructions
(supplied with SU-PW2 Wall-Mount Bracket).
Read these documents carefully for safety and
proper installation.
To Sony Dealers and Contractors
Provide full attention to safety during the
installation, periodic maintenance and
examination of this product.
Step 1: Check the parts
required for the
installation
Open the Wall-Mount Bracket package and check
the contents for all required parts along with the
Instructions.
Step 2: Decide on the
installation location
Decide where you want to install your Display
Unit. Turn to the back cover or inside the back
cover for the display installation dimensions and
determine the location.
If you intend to route the cables in the wall, also
determine the position of the cable hole and bore a
hole in the wall.
Installing the Display Unit
on a wall
The Display Unit can be installed on a wall by
attaching a Wall-Mount Bracket (sold separately).
Verify your TV’s model number and be sure to use
the bracket specified for your model only. Refer to
the Steps on this leaflet along with the Instructions
supplied with SU-PW2 Wall-Mount Bracket, to
properly carry out the installation.
Sufficient expertise is required for installing
this product. Be sure to subcontract the
installation to Sony dealers or licensed
contractors and pay special attention to safety
during the installation.
Sony is not liable for any damages or injury
caused by mishandling or improper
installation. Your Statutory Rights (if any) are
not affected.
2 (GB)
Hole for cable routing (One of two)
Refer to the Instructions for the SU-PW2.
Step 3: Install the Plate Unit on
the wall
Change the position of the Mounting Hook Unit
supported shafts.
Refer to the Instructions for the SU-PW2.
Prepare for the installation of
the Display Unit
3 Attach the four hooks with the four screws
(+PSW5 × L16) (supplied with SU-PW2).
Before removing the Table-Top Stand, disconnect
all the cables from the Display Unit.
1 Place the Display Unit, with its screen
facing down, on a stable, cloth-covered
work surface, at least 20 cm off the floor.
Screw into the
recessed screw
holes.
Note
When using an electric screwdriver, set the
torque setting to approximately 2 N·m.
2 Remove the screws that hold the Display
Unit to the Table-Top Stand and detach the
Table-Top Stand from the Display Unit.
GB
Step 4: Install the Display Unit
Refer to the Instructions for the SU-PW2.
Note
Remove the cable holder beforehand when it is
attached to the Display Unit. For details on the
cable holder, refer to the instruction manual of
the Display Unit.
(GB)
3
2 (CT)
CT
(CT)
3
2
3 (AR)
AR
(AR)
(AR)
32
English
Display installing dimensions table
F
A
G
C
Screen centre line/
393 ± 0.5
B
D
B
E
Display Model/
Display Dimensions/
H
Unit: mm/ Length for each mounting angle/
Unit: mm/ Weight/
Mounting angle (α°)/
A
KLV-V40A10
1015
B
684
C
122
D
286.5
F
G
0°
179
201
90
5°
226
190
100
10°
272
174
111
15°
316
155
121
20°
359
132
129
E
90
H
(× 4)*
27.2 kg
(108.8 kg)
* The wall must be strong enough to support at least four times the weight of the display that you are installing./
Printed in Japan