INSTALL GUIDE
640 Series Advanced Remote Vehicle
Security System
WWW.ULTRASTARTERS.COM
Technical Support- 866.698.5872
FCC/ID Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance
void the user’s authority to operate this devise.
INSTALL GUIDE
SECURITY SYSTEM
PAGE 2
Table of Contents
Table of Contents
Components
Wiring Diagram
Installation Tips
Pre-Installation Suggestions
Installation Suggestions
Mounting The Module
Installing The Program Button
Connecting The Starter Disable
Connecting The Dome Light Supervision
Under Hood Connections
Mounting The Siren
Wire Connectors
13 Pin Main Harness Connector
4 Pin Red Connector- Keyless Entry
4 Pin Additional Sensor Input
2 Pin Starter Disable Connector
Installation
Basic Installation - Quick start
Shock Sensor Programming
Test The System
Programming
Program Overview & System Reset
Program Menu 1 (User Settings)
Program Menu 2 (Alarm Settings)
Operations
Single & Dual Car Operation
Transmitter Programming
Battery Replacement
Other Features
System Service Mode
Service Mode- By remote
Diagnostics
Page 2
Page 3
Page 4
Page 4
Page 5
Page 6-7
Page 7-9
Page 10
Page 11
Page 12
Components
- Control Module
- Starter Disable Harness
- Two 4 Button AM Transmitters
- 4 pin Aux Sensor Harness
- Multi-Tone Siren
- AM 2way Antenna With Integrated
- 13 Pin Main Harness
LEDs and Program/Valet Switch
- Installation and Owner Manuals
- Window Decal
- 4 Pin Keyless Entry Harness With Driver’s Door Priority Output
INSTALL GUIDE
SECURITY SYSTEM
PAGE 3
Wiring Diagram
Built-in Starter Disable Relay (Normally Connected 87a & 30)
Siren Output (+)
3amp
(+) Siren
Brown
Programmable
Programmable
Constant Power
Chassis Ground
500ma
500ma
Channel 4
Horn/ Channel 5
Pink
Wht/Blue
(+) Input
(-) Input
Main Power
Red
(-) Trunk Release
500ma
15amp
Ground
(-) Trunk Release
(+) Park Lights
(-) When Armed
Black
Grey
Dome Light
(+) Door Input
Blk/White
Purple
Green
Park Lights
(-) While Armed
Dome Light Output
Positive Door Pin
Negative Door Pin
Hood Pin Switch
Switched Ignition
500ma
500ma
(+) Input
(-) Input
(-) Input
(-) Door Input
Hood Input
(+) Input
Ignition Input
ACTIVE RF ANTENNA**
White
Orange
Blue
Yellow
Status Led’s
Program Button
**The antenna MUST be connected for the system to operate
SIDE VIEW
Lock Output
Green
12vts Low Current Red
Blue
Unlock Output
Pink
2nd Unlock
**500ma outputs are low current and are designed to activate relays.
Programmable Output
Voltage Inverter Output
Programmable Output
Programmable Output
(-)500ma
(+)500ma
(-)500ma
(-)500ma
REAR VIEW
Auxiliary Sensor Connector This connector can be used to add additional
Alarm Sensors such as Radar, Glass Break or an additional shock sensor for
coverage at the rear of the vehicle.
(-) trigger Input
(-) trigger Input
Ground Output
12volt Output
(-)500ma Input
(-)500ma Input
(-)500ma Output
(+)500ma Output
Sensor
Sensor
Sensor
Sensor
Full - Warn
Pre - Warn
Ground
Power
Blue
Green
Black
Red
INSTALL GUIDE
SECURITY SYSTEM
PAGE 4
Recommended Pre-Installation Procedures
BEFORE STARTING INSTALLATION:
- Discuss the optional system features with the customer.
- Take a few minutes to review the installation and owners manuals.
- Do a walk around the vehicle and check for any damage.
- If installing a LED discuss the placement with customer before installing.
Recommended Installation Procedures
Mounting the Module
Never mount the module in the engine compartment. Select a location under the dash
to install the main module. Be certain that the module is securely attached and does not
obstruct any serviceable areas. Mount the module so that it cannot be seen if looking
under the dash as it could be easily unplugged by a thief. The module must be free from
all moving parts such as brake, clutch and gas pedals linkages.
Installing The Antenna
The antenna should be mounted in the top center of the windshield with the antenna mast
facing downwards. First ensure that the glass is clean and dry, remove the plastic from the
adhesive tape then press against the glass.
Connecting The Starter Disable
This system contains a built-in Starter disable relay. The brown starter kill wire from
the wire harness bag will connect to the module as normally connected. (87a & 30)
Cut the brown wire in half, then locate the vehicles starter wire. This wire will switch to
12volts in the crank/start position only. Cut this wire in half and confirm that the
vehicle will not start. Connect the brown wires, one to each side of the cut starter wire.
Route the brown wires to the main module and connect.
This output can be used to activate the interior lights upon disarming the alarm, connect
this output to a relay to activate the interior light. The dome light output will stay active for
30 seconds upon disarm.
Mounting The Siren
Choose a location in the engine compartment that is away from high sources of heat
and direct exposer to water. The siren should be mounted as well as grounded to solid
metal. Run the wiring for the siren so that it can not be seen or reached from below the
vehicle.
SECURITY SYSTEM
INSTALL GUIDE
PAGE 5
2 Pin Connector (Brown wire with female connectors)
Starter Disable harness. See page 4 for installation instructions
14 Pin Connector
Brown
(+) Siren Output
Pink
Channel 4 Output
Wht/Blue
Channel 5 Output
Red
Main Power Input
Black
Ground Input
Grey
(-) Trunk Release
White
(+) Park lights
Orange
(-) When Armed
Blk/White
(-) Dome Light
Purple
(+) Door Input
Green
(-) Door Input
Blue
(-) Hood Input
Yellow
Ignition Input
Positive output for siren*
Programmable - See menu 2**
Programmable - See menu 2***
Constant 12 Volt input
System ground input
Negative trunk release. 500ma****
Programmable - 10amp Maximum
Negative output when system is armed****
Dome light supervision****
Positive door pin switch input
Negative door pin switch input
Negative input from hood pin switch
Input from vehicles ignition wire
4 Pin Connector Blue
This connector is for the RF antenna. The antenna also contains 2 LEDs and the
Program Button.
4 Pin Connector Red
Green
Red
Blue
Pink
Door Lock
12 Volt Output
Door Unlock
Second Unlock
Programmable - menu 1, setting 3.
Output for voltage inverter only*****
Programmable - menu 1, setting 3.
Programmable - menu 1, setting 3******
4 Pin Connector White
Blue
Green
Black
Red
Sensor Full Warn
Sensor Pre Warn
Ground Output
12 Volt Output
Input trigger for addition alarm sensor(s)
Input trigger for addition alarm sensor(s)
Ground output for addition alarm sensor(s)
12 volt output for additional alarm sensor(s)
* This output is designed to operate one siren. If more than one is being added, a relay
must be installed to avoid damaging the module.
**Channel 4 is activated by holding the Star button on the transmitter.
*** Channel 5 must be programmed to activate on the # button. This channel works on
the horn output, if the 5th channel is programmed the horn output will function as
5th Channel.
****500ma outputs are low current and are designed to activate relays.
*****This is a low current 12volt output designed for use with a voltage inverter.
******This output will activate on the second press of unlock within 3 seconds.
INSTALL GUIDE
SECURITY SYSTEM
PAGE 6
Quick Start Install
Step 1 - Connect All Of the Following Wires
13 Pin Power Connector
Black
Yellow
Red
White
Brown
Green*
Purple*
Ground Input
Ignition Input
Main Power Input
(+) Park lights
(+) Siren Output
(-) Door Input
(+) Door Input
System ground input.
Input from vehicles ignition wire.
Constant power input
Programmable - menu 2, setting 3.
Positive output for siren.
Negative door pin switch input.
Positive door pin switch input.
*Test for door pin type (Positive or Negative) then connect the appropriate wire (Green or Purple)
Step 2- Plug-In The Module
When all the connections are done, the control module can be plugged in. Before connecting the
control module, make sure the ignition is in the OFF position. Plug in the 6 pin harness then the 14
pin followed by any other connectors that were used.
Step 3- Program, Test And Adjust The Shock Sensor
To program the Shock Sensor.
1.Press and hold the Lock and Unlock buttons for 5 seconds.
2.The system will chirp and the park lights will flash three times then stay “ON”.
3.Within 10 seconds impact vehicle in a safe place (i.e. - Window pillar) with amount of force
wanted to activate alarm. The siren will chirp upon learning the impact.
4. The Shock Sensor is now programmed.
5. Press the Unlock button to exit the Program Mode.
To test the Shock Sensor.
1. Press the Lock button once to arm the system.
2. Wait five seconds then impact the vehicle. Lighter impacts to the vehicle should trigger the warn
away (The siren will chirp three times). A harder impact to the vehicle will trigger the full
alarm.(The siren will activate for 60 seconds then turn off).
3. To deactivate the alarm when triggered, press the unlock button twice.
To adjust the Shock Sensor.
1. Repeat the shock sensor learning.
- If the sensor was to sensitive, impact the vehicle with greater force.
- If the sensor was not sensitive enough, impact the vehicle with less force.
*For best results ensure that the Control Module is mounted securely to the vehicle.
Test The System
1. Open all the vehicles windows.
2. Press the Lock button to arm the system.
3. Wait five seconds (or until the dome light goes out) then reach in through a window and open
the door.
The alarm will then activate (repeat on all the doors).
4. Test the Shock Sensor again and adjust if necessary.
5. Insure that all additional features are working as intended.
6. If necessary proceed to Program Mode to adjust the programmable outputs.
Your Basic Install Is Complete!
SECURITY SYSTEM
INSTALL GUIDE
PAGE 7
Programming Overview
Program mode allows you to adjust the settings and options of your system.
Your system has been intelligently designed by installers with years of experience. The system’s
default settings do not require any program changes in most cases. However, this system does
incorporate a highly advanced programming system that includes 2 menus with numerous options
and settings that can be easily adjusted for custom installations and applications.
Entering Program Mode
To Enter Program Mode
1) Make sure ignition is in the off position.
2) Within three seconds turn the key ON - OFF - ON - OFF - ON. Leave Key ON.
3) Press and release the Program Button one time.
4) Park lights will come and the siren will chirp to confirm entering Program Mode.
5) Select Desired Program Menu by the following:
Press Button #1
Lock
User Options Page 8.
Press Button #2
Unlock
Alarm Settings Page 9.
6) The selected mode will be confirmed by a siren chirp and one park light flash.
7) The Program Menu may be changed at any time by pressing the transmitter buttons as
above, this allows the installer to change a setting from one menu, then quickly jump to
another menu and change another setting without exiting Program Mode.
8) Program Mode will be exited if there is no activity for 30 second or if the key is turned to the
“Off” position. This will be confirmed by one siren chirp and park light flash.
Note: If unit does not enter Program Mode, turn ignition off and repeat steps 1-4.
** The ignition wire(Yellow) MUST be connected to the vehicle’s ignition wire. If it is not
connected it will not be possible to enter the Program Modes.
Changing the Programmable Settings
To Select and Change A Program Setting:
1) Enter Program Mode.
2) Select the desired Program Menu. (See pages 8&9)
3) Press & release the Program Button the correct number of times to select the desired
Program Setting(as listed on pages (8&9). The park lights will flash and the siren will chirp to
indicate the current setting that is selected.
4) Press and hold the Program Button until the parking lights / siren confirm the selected setting.
The park lights will flash and the siren will chirp to indicate the option selected within the setting.
5) Turn the ignition key “Off” to exit Program Mode.
SYSTEM RESET
STEP 1 - Within three seconds turn the key ON-OFF-ON-OFF-ON (Leave the Key ON).
STEP 2 - Press and release the Program Button.
STEP 3 - Park Lights will come ON
STEP 4 - Press the Program Button a second time and hold for 8 seconds until the park lights
flash 3 times and siren chirps 3 times.
System is now re-set to factory defaults.
NOTE: Reset to defaults does not delete the transmitters from memory.
INSTALL GUIDE
SECURITY SYSTEM
PAGE 8
Menu 1 - User Settings
Setting 1- Ignition Auto Lock
1 Ignition Lock & Unlock Enabled
2 Ignition Lock Only
*3 Ignition Auto Lock Disabled
1 Light Flash
Doors Lock/Unlock when the key is turned On/Off
2 Light Flashes Doors Lock when ignition key is turned ON only
3 Light Flashes Doors do not Lock or Unlock with Ignition key
Press the Program Switch 1 time to select setting 1 (This will be confirmed by 1 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 2- Horn Honk Settings
1 Lock & Unlock chirps Disabled
*2 Chirps Enabled
1 Flash
3 Flashes
A audible chirp for Panic Mode only
Chirp indication for all functions
Press the Program Switch 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 3- Door Lock Options
1 Double Pulse Unlock
2 3 Second Lock & Unlock
*3 0.75 Second Pulses
1 Flash
2 Flashes
3 Flashes
Single .75 second lock and double unlock pulse
3 second pulses for lock & unlock
0.75 second pulses for lock and unlock
Press the Program Switch 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 4 -Sensor - Enable / Disable
1 Sensors Disabled
* 2 Sensors Enabled
1 Flash
2 Flashes
Shock sensor and Aux. Sensor disabled
Shock Sensor and Aux. sensor enabled.
Press the Program Switch 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 5 - Passive / Active Arming
1 Passive Arming
2 Active Arming With Rearm
* 3 Active Arming
1 Flash
2 Flashes
3 Flashes
Auto Arms 30 seconds after last door is closed
Unlock is pressed and no door is within 30 sec.
Alarm arm by remote transmitter only.
Press the Program Switch 5 times to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 6 - Active / Passive Locks
1 Active Locking
*2 Passive Locks
1 Flash
2 Flashes
Doors do not auto-lock with passive arming
Doors Auto-Lock with passive arming.
Press the Program Switch 6 times to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
INSTALL GUIDE
SECURITY SYSTEM
Menu 2- Alarm Settings
PAGE 9
Setting 1 - Car Finder/ 5th Channel
1 Car Finder OFF
1 Light Flash
Car Finder Mode Disabled
*2 Car Finder ON
2 Light Flashes
Car Finder Mode activated when # button is held.
**To operate the 5th channel on button #4, setting 7 must be programmed for 5th channel output.
Press the Program Switch 1 time to select setting 1 (This will be confirmed by 1 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 2 - Secure Program Mode
1 Secure Program Active
2* Normal Program Active
1 Flash
2 Flashes
Ignition “ON” and Program switch held for 15 seconds
Ignition “ON” and Program switch held for 5 seconds
Press the Program Switch 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 3 - Park Light Output
1 Parking Lights on Disarm
2 Negative Park Light
3* Normal Parking Lights
1 Flash
2 Flashes
3 Flashes
Park Lights on for 30 seconds on disarm
Switches Park Light and the Trunk Release outputs
2 Park Light Flashes on disarm
Press the Program Switch 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 4 - Horn Honk Timing
1 5ms Pulsed Output
1 Flash
Short (Quiet) Pulses
2 20ms Pulsed Output
2 Flashes
Long (Loud) Pulses
*3 10ms Pulsed Output
3 Flashes
Normal (Medium) Pulses
Press the Program Switch 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 5 - 4th Channel Settings
1 Pulsed Output
1 Flash
Pulsed for 0.75 seconds upon 4th Channel Activation
2 Latched Output
2 Flashes
Latched until repeated or ignition “ON”
*3 Active Output
3 Flashes
Active for as long as the button is held on Transmitter.
Press the Star buttons to activate the 4th Channel output.
The Shock Sensor and ignition will be bypassed upon 4th channel activation.
Press the Program Switch 5 times to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 6 - Car Jack Mode
1 Type 1
1 Flash
Press button #4 or open the door while the Ignition is “ON”
2 Type 2
2 Flashes
Press button #4 or by turning the Ignition “On”
*3 Car Jack OFF
3 Flashes
No Car Jack Functions
Press the Program Switch 6 times to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 7 - Horn/ 5th Channel
1 5th Channel
2 LED Output
*3 Horn Honk
1 Flash
2 Flashes
3 Flashes
Active for as long as the # button is held on Transmitter.
Pulsed output for addition LED activation
Horn Honk with Arm & Disarm Chirps
INSTALL GUIDE
SECURITY SYSTEM
PAGE 10
First Car Operation
Press Once to Lock the doors and arm the alarm. Hold for Panic Mode.
Press a second time and hold for Constant Lock Output.
First Car
Press once to unlock the doors and disarm the alarm
Press and hold for the Trunk / Aux Output
Press this button to activate the 4th channel output.
This output can be used to activate additional alarm features.
Press once and hold for Car Finder
Press and release then hold to activate/deactivate Service Mode.
Second Car Operation (Optional)
2nd Car
then
&
&
&
then
=
=
=
=
Press Once to Lock and arm the alarm. Hold for Panic Mode.
Press a second time and hold for Constant Lock Output.
Press once to unlock the doors and disarm the alarm
Press and hold for the Trunk / Aux Output
Press this button to activate the 4th channel output.
This output can be used to activate additional alarm features.
Press once and hold for Car Finder
Press and release then hold to activate/deactivate Service
Mode.
Transmitter Programming
Step 1 - Within three seconds turn the ignition ON-OFF-ON-OFF-ON - Leaving ON.
Step 2 - Press and hold the Program Switch - Parking Lights will come ON **if park
lights do not come on at this point, turn key off for 5 seconds, then repeat step 1.
Step 3 - Continue to hold the Program Switch, the park lights will turn off. (Continue
holding the switch)
Step 4 - Press the LOCK button on each of 1st car remote’s and press the # button
on Each of the 2nd car remote’s of the transmitters to be programmed pause for
about 2-3 seconds between each remote. The park lights will Flash once and the siren
will chirp once each time a new code is learned.
Note: Pause for no more than 2 seconds between transmitters All the
transmitters to be used must be programmed at the same time. All transmitters
not programmed at this time will be erased from memory for security. The
system holds a maximum of 3 transmitter codes including 2nd car remote codes.
You can program the same remote as a 1st car remote in one vehicle and as a 2nd car
remote in a second vehicle.
SECURITY SYSTEM
System Service Mode
INSTALL GUIDE
PAGE 11
ACTIVATING SERVICE MODE
1. While the ignition is “ON” press and hold the Program Button for five seconds. The
park lights will flash and the siren will chirp five times to confirm that the system is in Service Mode.
2. While in Service Mode the remote start functions will be disabled and LEDs will be “ON” steady.
Door locks and trunk release are still operational.
DEACTIVATING SERVICE MODE
1. While the ignition is “ON” press and hold the Program Button for five seconds. The park lights will
flash and the siren will chirp two times to confirm that the system has exited Service Mode.
2. All Alarm Functions are reactivated.
Service Mode- By Remote
SERVICE MODE ACTIVATED
1 - Press and release button 4 then hold Button 4 again for 6 seconds or until the status
LEDs comes on solid.
NOTE: The siren will chirp 5 times as confirmation.
SERVICE MODE DEACTIVATED
1 - Press and release button 4 then hold Button 4 again for 6 seconds or until status
LEDs turns of.
NOTE: The siren will chirp 2 times as confirmation.
Anti Car Jacking Mode
Only program this feature if it specifically requested by the customer. Ensure that user is
fully trained on the operation of this feature. When car jack mode is activated the system
will no longer respond to the remote transmitters. If the starter disable feature was installed
the vehicle will not start.
When the Car Jack Mode is activated the system will start flashing the LED rapidly for five seconds.
The park lights and siren will then activate once every second for 10 seconds in Countdown Mode.
After 10 seconds the alarm will trigger into Full Alarm, the system will no longer respond to the
transmitters and the starter disable output will activate to disable the vehicle from starting.
ACTIVATING CAR JACK MODE
Program Menu 2, Setting 5
- Type 1- Car Jack Mode will activate if the door is opened while the ignition key is in the “On” position.
Car Jack Mode may also be activated by pressing the # button on the remote transmitter
while the ignition key is in the “On” position.
- Type 2- Car Jack Mode will activate if the ignition key is turned to the “On” position. Car Jack Mode
may also be activated by pressing the # button on the remote transmitter while the ignition
key is in the “On” position.
DEACTIVATING CAR JACK MODE
1.During the Countdown Mode - Turn the ignition key “ON” then press and release the Program
Button one time.
2. After Full Alarm - Turn the ignition key “Off” then “ON” then press and hold the Program
Button until the alarm turns off. (About Eight seconds)
Note: If Car Jack Mode goes into full alarm mode, the system will ignore the remote transmitters and
this may result in the transmitter needing to be reprogrammed.
INSTALL GUIDE
SECURITY SYSTEM
PAGE 12
Diagnostics
Alarm Diagnostics
If the alarm system is triggered while armed, the system will retain in memory the cause of the trigger. The
diagnostics can then be used to determine what the cause of the trigger was. When disarming the alarm, the
siren/horn will chirp 3 times instead of the usual 2 times to indicate the alarm had been triggered.
The system’s LED will also flash in pulses to indicate which input triggered the alarm.
NOTE: LED status will be cleared when ignition is turned ON. For proper memory clearing, insure
to connect the ignition input to the ignition on the vehicle.
Diagnostics Chart
Siren Chirps on Disarm
LED Flashes
Diagnostic
Three Chirps
Three Chirps
Three Chirps
None
None
None
None
On/Off
Two Flashes
Three Flashes
Four Flashes
Off
On Solid
Single Flashes
Rapid Flashes
Rapid Flashes
Shock Sensor Was Activated
Door/Hood Pin Input Triggered
Ignition Input Triggered
System Disarmed
System in Valet/ Service Mode
Alarm System is Armed
Passive Arming Countdown
Car Jack Mode Countdown
Additional LED Flashes
While the system is disarmed and the ignition is in the off position, the LEDs will
activate from the following triggers.
1) If the door is opened the LEDs will stay on until the door is closed.
2) If the hood is opened the LEDs will stay on until the hood is closed.
3) If the shock sensor detects vibration the LEDs will turn on momentarily.
4) If the auxiliary sensor input is activated the LEDs will activate momentary.
Download PDF