Element 26+ User`s Manual 20070228.indd

FLX-3210
32” LCD Television
This product contains electrical or electronic materials. The presence of these materials may, if
not disposed of properly, have potential adverse effects on the environment and human health.
Presence of this label on the product means it should not be disposed of as unsorted waste
and must be collected separately. As a consumer, you are responsible for ensuring that this
product is disposed of properly.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Confidential unpublished works. © 1992 -1997 Dolby Laboratories, Inc. All rights reserved.
This TV incorporates High-Definition Multimedia Interface (HDMITM) technology.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
FCC
Federal Communications
Commission Statement
1. Reorient/Relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit which is different from what the receiver is
connected to.
4. Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the manufacturer
responsible for compliance could void the user authority to operate the
equipment.
1
ENGLISH
This equipment has been tested and found to comply with the limits of a class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Warnings and Precautions
Warnings and Precautions
To prevent any injuries, the following safety precautions should be observed in the installation, use,
servicing and maintenance of this equipment.
Before operating this equipment, please read this manual completely, and keep it nearby for future
reference.
This symbol is intended to alert the user to avoid the risk of electric shock.
This equipment must not be disassembled by anyone except qualified service personnel.
WARNING
CAUTION
This symbol is intended to alert the user to the presence of important operating and
maintenance instructions in the literature accompanying the appliance.
To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture.
▪
▪
▪
▪
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Use of controls, adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
Important Safety Instructions
This symbol indicates caution points.
This symbol indicates actions that should not be done.
This symbol indicates actions that must be performed.
▪ Do not place the equipment on any uneven or unstable carts, stands, tables, shelves etc.
The equipment may fall, causing serious injury to children or adults and serious damage to
the equipment itself.
▪ Use only a cart or stand recommended by the manufacturer. This equipment and
recommended cart or stand should be handled with care. Quick stops, excessive force, and
uneven surfaces may cause the equipment and cart/stand to overturn.
▪ Do not disable the 3-wire grounding type plug. The grounding pin on the 3-prong plug is an
important feature. Removing the grounding pin will increase the risk of damaging the
equipment.
▪ If you can not fit the plug into the electrical outlet, contact an electrician to install a grounding
outlet.
▪ Always operate this equipment from the type of power source indicated on the rear of the
serial/model plate.
▪ Never overload wall outlets and extensions.
2
Warnings and Precautions
▪ Use and handle the power cord with care. Do not place any heavy objects on the AC
power cord.
▪ Do not touch the power cord and antenna cable during lightning.
▪ Remove the plug from the wall outlet, if the equipment will not be used for a long period
of time.
▪
Do not place, use or handle this equipment near water.
▪
Never expose the equipment to liquid, rain, or moisture.
Seek for service if any of the above is spilled into the equipment.
▪
Do not expose the equipment to extreme temperature or to direct sunlight, as the
equipment may heat up and suffer damage.
▪
Do not install the equipment near any heat sources such as radiators, heat registers,
stoves, or any other apparatus that might produce heat.
▪
Do not attempt to service the equipment yourself.
▪
Opening and removing the covers may expose you to dangerous voltage or other
hazards and may void your warranty. Refer service to qualified personnel.
▪
Do not place or drop any other objects on top.
▪
Do not insert anything into the ventilation holes of your equipment.
Inserting any metal or flammable objects may result to fire or electric shock.
▪
Protect the power cord from being walked on or pinchrd particularly at plugs ,convenience
receptacles, and the point where they exit from the apparatus.
▪
Do not place the equipment on uneven or unstable carts, stands, tables, shelves etc. The
equipment may fall, causing serious injury to children or adults and serious damage to
the equipment itself.
Always place the equipment on the floor or on a surface that is sturdy, level, stable and
strong enough to support the weight of the equipment.
▪
Do not block any ventilating openings. Leave an open space around the equipment.
Never place the equipment :
on a bed, sofa, rug, or any other similar surfaces; too close to drapes/curtains/walls, in a
bookcase, built-in cabinet, or any other similar places that may cause poor ventilation.
▪
Unplug this apparatus during lightning storms or when unused for long periods of time.
▪
Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
▪
Always remove the power cord from the outlet before cleaning the equipment.
▪
Never use liquid or aerosol cleaners on the equipment.
Clean only with a soft dry cloth.
▪
Only use attachments/accessories specified by the manufacturer.
3
ENGLISH
▪ Do not pull the AC power cord. Do not handle the AC power cord with a wet hand.
Warnings and Precautions
Outdoor Antenna Safety Instructions
If an outdoor antenna is connected, follow the precautions below:
▪ An outdoor antenna should not be located in any area where it could come in contact with
overhead power lines, or any other electric light or power circuits.
▪
When installing an outdoor antenna system, extreme caution should be taken to prevent
contact with power lines. Direct contact with power lines may be fatal and should be avoided
at all costs.
Section 810 of National Electrical Code (NEC) provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for
the grounding electrode.
Antenna lead-in wire
Ground clamps
Antenna discharge unit
(NEC section 810-20)
Electric service
equipment
Grounding conductors
(NEC section 810-20)
Ground clamps
Power service grounding
(NEC Art250 part H)
NEC : National Electrical code
EXAMPLE OF OUTDOOR ANTENNA GROUNDING
4
TABLE OF CONTENTS
Warnings and Precautions
Important Safety Instructions ....................................................................................... 2
Antenna Safety Instructions ......................................................................................... 4
Chapter 1 Introducing the LCD TV
Key Features ............................................................................................................... 6
Package Contents ....................................................................................................... 7
Setting Your LCD TV.................................................................................................... 8
Your LCD TV .............................................................................................................. 10
Your Remote Control ................................................................................................. 12
Chapter 2 Installing the LCD TV
Connecting a TV Cable or an Antenna ...................................................................... 14
Connecting a VCR ..................................................................................................... 19
Connecting a Video Camera or Game Console ........................................................ 20
Connecting a DVD Player .......................................................................................... 21
Connecting a Digital TV Cable Box or Digital Satellite Receiver ............................... 23
Connecting an AV Equipment with HDMI Connector ................................................. 24
Connecting an AV Equipment with DVI Connector .................................................... 25
Connecting a PC........................................................................................................ 26
Connecting an Audio Receiver or a Dolby Digital 5.1 Sound System........................ 27
Chapter 3 USING THE FEATURES
Wide Screen Viewing...................................................................................................................................29
Operating the Menu .....................................................................................................................................30
Customizing the VIDEO Settings...........................................................................................................32
Customizing the AUDIO Settings...........................................................................................................34
Customizing the TV Settings....................................................................................................................36
Customizing the SETUP Settings .........................................................................................................38
Using the Program Block Settings ........................................................................................................ 41
Using the Program Guide ..........................................................................................................................46
Specifications ........................................................................................................ 47
5
ENGLISH
Federal Communications Commission Statement .......................... 1
Chapter 1 Introducing the LCD TV
Chapter 1
Introducing the LCD TV
Key Features
Various Audio/Video terminals for external equipment connection
▪
▪
▪
▪
▪
▪
▪
▪
2 sets of composite A/V input terminals
1 set of S-VIDEO terminals
2 sets of component Video input terminals
1 VGA/ Audio input terminals
1 HDMI/Audio input terminals
1 set of Audio(L/R) output terminals
2 SPDIF output terminals (Optical x 1 /Coaxial x 1)
1 Headphone terminal
The built-in TV tuner to receive HD ATSC
▪ This function allows the reception of HD broadcasting without the addition of a set top
box.
High Definition Multimedia Interface (HDMI)
▪ High Definition Multimedia Interface (HDMI) is a small, user-friendly interconnect that
can carry up to 5 Gbps of combined video and audio in a single cable. This system
eliminates the cost, complexity and confusion of multiple cables used to connect
current A/V systems.
HDTV Component Video Inputs
▪ Offers the best video quality for DVD(HD1080p,1080i, 720p) and digital set-top-box
(HD1080p,1080i, 720p) connections.
3D Digital Noise Reduction
▪ This function can digitally reduce image noise to provide better picture quality.
Film-Mode Detection (3:2 Reverse Pull Down)
▪ This function can automatically detect content derived from film and adjust the
interlacer’s frame matching to provide a more natural-looking, clearer image of the
moving picture.
6
Chapter 1 Introducing the LCD TV
Package Contents
LCD TV
Bottom Stand /
Screw Driver and Screws (4~6)
Remote Control/
AAA Batteries x 2
S.MODE
MTS
P. MODE
CAPTION
SLEEP
P.SIZE
VIDEO Cable
Component Cable
AUDIO Cable
Warranty Card
MUTE
VOL.
GUIDE
INFO
INPUT
CH.
EXIT
MENU
Power Cord
User’s Manual
Quick Start Guide
Stand Assembly Guide
Remote Control Guide
These items are all you need to set up and operate the LCD TV in its basic configuration.
Make sure all of the above contents are included in the package. If you are missing
any items, please contact the Element Electronics customer service department.
7
ENGLISH
Make sure all of the following contents are included.
Chapter 1 Introducing the LCD TV
Setting Up Your LCD TV
How to install the TV Stand
Read all instructions before continuing with the stand installation.
Attach the Stand the TV with the bottom foam packaging material still
attached.
a.
b.
Lift foam packaging material from the top of the LCD out of the box.
Lift LCD out of the box, with the bottom foam packaging material still attached, and place
onto a stable surface.
a
b
Protective bag
Stand
c.
d.
Shipping box
Table
Remove protective bag from LCD unit, but DO NOT remove the bottom foam packaging
material from the TV.
Locate the place on the back of the TV to attach the stand. Secure the stand to the LCD
with all six screws.
Unit
c
Table
Stand
Packaging material
d
Unit
Table
Screws
Stand
Packaging material
8
Chapter 1 Introducing the LCD TV
How to remove the TV Stand
If you prefer to mount your new Element Electronics TV on a wall instead of attaching it to the
stand, please reference the instructions included in the wall mounting kit (sold separately).
To prevent damaging the surface of the LCD TV, place the TV on a soft cloth.
Soft cloth
Remove the screws of the table stand and detach the table stand from the TV.
Soft cloth
Table stand
Align the holes on the wall mounting hook units with the corresponding holes on the rear
of the TV and fasten four screws.
4 screws (supplied
with the wall mount
kit)
Wall mounting hook
unit (supplied with the
wall mount kit)
Soft cloth
9
ENGLISH
Verify your TV’s model and be sure to use the wall mounting kit (100 x 100)
specified for your TV model only. Contract a qualified technician for
assistance when installing the wall mounting kit.
Chapter 1 Introducing the LCD TV
How to setup the TV
Use a supplied antenna cable to connect the VHF/UHF signal to the LCD TV’s ANT. terminal
(refer to page15-17).
Connect the AC power cord at the back of the TV and connect the power cord to wall outlet.
Insert the 2 batteries supplied in remote control.
Step1
Slide the back cover up to open the
battery compartment of the remote
control.
Step2
Insert two AAA size batteries.
Make sure to match the (+) and
( - ) ends of the batteries with
the (+) and ( - ) ends indicated
in the battery compartment.
Slide the cover back into place.
Do not use caustic cleaners (porcelain, stainless steel, toilet, or oven cleaner
etc.) on the remote, as it may suffer damage.
To connect to another external A/V device, refer to pages 19-27.
10
Chapter 1 Introducing the LCD TV
Your LCD TV
Front/Right Side View and Controls
ENGLISH
LED
The LED light indicates when the LCD TV is
activated.
VIDEO
L
AUDIO
R
IR
Infrared
Receiver
VIDEO
VOLUME+Adjusts the volume up and down.
Selects the main-menu item and
change values for items when in the
OSD mode.
L
R
VIDEO1 IN
CHANNEL▲▼
Scans up and down through channels.
Selects sub-menu item when in the OSD
mode.
VIDEO1 IN
MENU
Press once to display the OSD (on screen
display), press again to turn the OSD off.
Connects to the composite
Video and Audio output jacks
on external video equipment.
INPUT
Chooses from different input signal sources.
HEADPHONE
Connects to the external
headphone for private
listening.
Turns the LCD TV on and into standby mode.
11
Chapter 1 Introducing the LCD TV
Rear View and Jacks
VIDEO2 IN
Connects to the composite VIDEO and AUDIO(L/R) output jacks on external video equipment.
HDMI IN
Connects the all digital AV equipment with HDMI connector.HDMI supports enhanced,
high-definition video and two-channel digital audio. The AUDIO(L/R) of HDMI IN is for
DVI connection.
S-VIDEO IN
Connects to the S-VIDEO and AUDIO(L/R) output jacks on external
video equipment.
VGA IN
Connects the PC, or other AV equipment with VGA and
AUDIO(L/R) output jacks.
HDMI IN
VGA IN
AUDIO OUT
YPbPr1 IN
AUDIO
Y
AUDIO
Pb
Pr
STEREO
AUDIO
DIGITAL
OPTICAL
HDTV/TV
Air/Cable
L
R
L
R
L
Y
Pb
Pr
R
L
COAXIAL
AUDIO
VHF/UHF IN
VIDEO
L
AUDIO
VIDEO2 IN
R
L
R
S-VIDEO
AUDIO
S-VIDEO IN
YPbPr2 IN
L
R
R
YPbPr1 IN/YPbPr2 IN
Connects to the DVD player, Digital Set-Top-Box, or other AV
equipment with component(YPbPr) video and audio output jacks.
AUDIO OUT-STEREO
Connects to the AUDIO(L/R) input jacks on AV equipment.
AUDIO OUT-DIGITAL-OPTICAL/
COAXIAL
Connects to the DIGITAL AUDIO
jack on digital/standard 5.1 audio
system.
AIR/CABLE IN
Connects RF input from VHF/UHF antenna or cable
to receive high/standard definition television.
AC IN
Connects to the AC power cord.
12
Chapter 1 Introducing the LCD TV
Your Remote Control
1
22
MTS
Cycles through the multi-channels TV
sound(MTS) options: SAP/MONO/
STEREO
3
S.MODE
Selects sound effect options: Surround/
Live/Dance/Techno/Classic/Soft/Rock/
Pop/Off.
4
P.MODE
Selects picture mode: Vivid/Hi-Bright/
Cinema/Sport/User
P.SIZE
Cycles through Wide mode settings :
NORMAL /FULL/WIDE/ZOOM
CAPTION
Cycles through the Closed Caption:
Anlalog Closed Caption:CC1/CC2/
CC3/CC4/TT1/TT2/TT3/TT4/Off
2
S.MODE
MTS
P. MODE
CAPTION
SLEEP
P.SIZE
3
4
6
5
7
5
8
6
9
10
Digital Closed Caption:Service1/
Service2/Service3/Service4/Service5/
Service6/Off
MUTE
12
11
VOL.
GUIDE
INFO
INPUT
CH.
7
SLEEP
Cycles through the LCD TV sleep timer:
OFF/10/20/30/40/50/60/90/120 mins
8
0-9
Select and switch to a channel by using
0-9 buttons.
EXIT
In HDTV mode, use with 0-9 and
buttons to select a digital channels.
MENU
9
JUMP
Returns to previously selected channel.
10 MUTE
Mutes and restores the audio
11 VOL.+-
Increases and decreases volume.
12 CH.+-
Scans up and down the channels
13
ENGLISH
Turns the LCD TV on and off.
1
Chapter 2 Installing the LCD TV
13
S.MODE
MTS
P. MODE
CAPTION
SLEEP
P.SIZE
INPUT
Pressing INPUT display the source list,
use ▲▼ to select the video equipment
connected to the video inputs of your
LCD TV : TV/HDTV/VIDEO1/VIDEO2/
VIDEO3/VIDEO4/VIDEO5/VIDEO6/
COMPUTER
Input Source
TV(CABLE/AIR)
VIDEO1 (SIDE)
VIDEO2 (REAR)
VIDEO3 (S-VIDEO)
VIDEO4 (YPbPr1)
VIDEO5 (YPbPr2)
VIDEO6 (HDMI1)
VIDEO7 (HDMI2)
COMPUTER(VGA)
14 GUIDE
Displays the Program Guide on the
screen. Pressing again to turn GUIDE off.
15 EXIT
Exits the OSD menu.
16 ▲▼►◄
Cycles through OSD options and
selects individual menu items. OK
confirms option settings.
MUTE
VOL.
13
GUIDE
INPUT
OK
CH.
EXIT
16
INFO
17
17 INFO
Pressing repeatedly displays a variety of
information such as the current channel
and the input source.
18 MENU
Displays the OSD menu on the screen.
15
14
MENU
18
Effective range:
The remote can control the LCD TV from up to 5m away, if pointed directly at the receiver.
14
Chapter 2 Installing the LCD TV
Chapter 2
Installing the LCD TV
Connecting a TV Cable or an Antenna
Antenna Connection
The antenna requirements for good color TV reception are more important than those for a black &
white TV reception. For this reason, a good quality outdoor antenna is strongly recommended.
The following is a brief explanation of the type of connection that is provided with the various antenna
systems.
■ A 75-ohm system is generally a round cable (not included) with Ftype connector that can easily be attached to a terminal without
tools.
F-type connector
75-ohm coaxial cable (round)
■ A 300-ohm system is a flat twin-lead cable (not included) that can
be attached to a 75-ohm terminal through a 300-75-ohm adapter
(not included).
300-ohm twin-lead cable (flat)
15
ENGLISH
Refer to the owner’s manual of any external equipment to be connected.
When connecting any external equipment, do not connect any AC power cords to wall outlets
until all other connections are completed.
Chapter 2 Installing the LCD TV
Use one of the following two diagrams when connecting an outdoor antenna.
A: Shows how to use a VHF/UHF combination outdoor antenna.
B: Shows how to use a separate VHF and/or UHF outdoor antenna.
A. Combination VHF/UHF antenna
VHF/UHF
Antenna
300/75-ohm adapter
(not included)
300-ohm twinlead cable
VHF/UHF
Antenna
75-ohm
coaxial cable
B. Separate VHF and/or UHF antennas
UHF
Antenna
Combiner
300-ohm twin(not included)
lead cable
OUT
IN
75-ohm
coaxial cable
300-ohm twinlead cable
16
VHF
Antenna
Chapter 2 Installing the LCD TV
Cable TV (CATV) Connection
■ A 75-ohm coaxial cable connector is built into the set for easy hookup.
When connecting the 75-ohm coaxial cable to the set, connect the 75ohm cable into the ANT. terminal.
■ Some cable TV companies offer premium pay channels. Since the
signals of these premium pay channels are scrambled, a cable TV
converter/descrambler is generally provided to the subscriber by the
cable TV company.
This converter/descrambler is necessary for normal viewing of scrambled channels.
(Set your TV to channel 3 or 4, typically one of these channels is used. If this is unknown,
consult your cable TV company.)
For more specific instructions on installing cable TV, consult your cable TV company.
One possible method of connecting the converter/descrambler provided by your cable TV
company is shown in the diagram below.
RF switch
(not included)
OUT
VHF/UHF IN
2 set signal
splitter
(not included)
A
IN
B
Cable TV converter/
descrambler
(not included)
■ The RF switch (not included) is required to provide two inputs (A and B). Setting
the RF switch to position A allows viewing of all unscrambled channels by using
the TV channel keys.
■ Setting the RF switch to position B allows viewing of all scrambled channels via
the converter/descrambler by using the converter channel keys.
17
Cable TV Line
ENGLISH
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the
National Electrical Code (NEC) that provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the grounding system of the building
accurately, or as close to the point of cable entry as possible. Use of this TV for other than
private viewing of programs broadcasted on UHF, VHF or transmitted by cable companies for
the use of the general public may require authorization from the broadcast/cable company, and/
or program owner.
Chapter 2 Installing the LCD TV
Use a supplied antenna cable to connect the TV signal to the LCD TV’s TV CABLE terminal.
HDTV/TV
Air/Cab
le
VHF/UHF IN
Connect the AC power cord at the back of the TV and connect the power cord to wall outlet.
HDTV/TV
Air/Cab
le
VHF/UHF IN
This TV is equipped with a safety fuse. In the event of an electrical storm or power outage
the safety fuse is designed to protect your TV. If your TV has no power, check the fuse by
prying the cover off, following the illustration below.
If the fuse is blown, visit your local hardware store and ask for a 4A 250V - 5x20mm Time
Lag Fuse (Slow Blow) to replace the fuse.
Firm Plastic Prying Tool
(Using a metal tool may cause shock)
4A 250V
5x20mm
Fuse
Back of TV
BE SURE TO UNPLUG AC POWER CORD BEFORE REMOVING THE FUSE.
Press the
button on the remote to turn on the LCD TV.
Always disconnect the LCD TV from the main power source when the LCD TV will not be used
for a long period of time. The POWER button on the front panel is only used for switching the
LCD TV into the standby mode, it does not disconnect the device from the main power
source. To completely disconnect the main power source, please remove the power cord’s
plug from the socket.
18
Chapter 2 Installing the LCD TV
Press the
button on the remote to turn on the LCD TV.
ENGLISH
Main
TV(CABLE/AIR)
VIDEO1 (SIDE)
VIDEO2 (REAR)
VIDEO3 (S-VIDEO)
VIDEO4 (YPbPr1)
VIDEO5 (YPbPr2)
VIDEO6 (HDMI)
COMPUTER(VGA)
Press the INPUT button on the remote to display the Input List. Use the ▲▼ buttons to
select TV and press the OK button.
Channel Scan
Tuner Mode
Channel Skip
Time Zone
TV
Cable
Eastern Time
Select
Exit
Press the MENU button on the remote control to display the Main menu, and use the ◄►
buttons to select the TV.
Status: Scanning.....
Analog Channels: 25
Digital Channels: 0
Cable
47%
The Channel Scanning will create a list of receivable channels for the current
input (antenna or cable). You will be required to run Channel Scanning for each
RF input to create a list of available channels from both inputs.
Press the OK button to display the received channel list, then press ▲▼ to select a
channel. Or, use the ▪ (Input button) with 0-9 buttons to select digital channel( for
example 9.1)
Channel List
5-2 RF5-2
9-1 KQED-HD
9-2 KOED-SD
8 CCT
12
13
15
The digital main channel might include many subchannels (for example 9-1, 92..) that are showing program at the same time.
19
Chapter 2 Installing the LCD TV
Connecting a VCR
Rear of TV
HDMI IN
VGA IN
AUDIO OUT
YPbPr1 IN
AUDIO
AUDIO
Y
Pb
Pr
STEREO
AUDIO
DIGITAL
OPTICAL
HDTV/TV
Air/Cable
L
R
L
R
L
Y
Pb
Pr
R
L
COAXIAL
AUDIO
VHF/UHF IN
VIDEO
L
AUDIO
VIDEO2 IN
R
L
R
S-VIDEO
AUDIO
S-VIDEO IN
YPbPr2 IN
L
R
R
AUDIO Cable
S-VIDEO Cable
AV Cable
A
B
METHOD A:
Use a composite cable to connect the VCR’s composite video/audio jacks to the LCD TV’s
VIDEO2 IN jacks.
METHOD B:
Use an audio cable to connect the VCR’s audio output jacks to the LCD TV’s audio
inputs. Use a S-Video cable to connect the VCR’s s-video output jack to the LCD TV’s
S-VIDEO IN input jack.
Connect all AC power sources, before turning on the power switch of the LCD TV or
other connected equipment.
Press the
button on the remote to turn on the LCD TV.
To watch a videotape, press the SOURCE button on the remote to select
VIDEO2( METHOD A), or VIDEO3 (METHOD B).
20
Chapter 2 Installing the LCD TV
Connecting a Video Camera or Game console
Rear of TV
HDMI IN
ENGLISH
Right Side
VGA IN
AUDIO OUT
VIDEO
YPbPr1 IN
AUDIO
AUDIO
Y
Pb
Pr
STEREO
AUDIO
DIGITAL
OPTICAL
L
HDTV/TV
Air/Cable
L
R
L
R
L
Y
R
Pb
Pr
R
L
COAXIAL
AUDIO
VIDEO1 IN
VHF/UHF IN
VIDEO
L
AUDIO
VIDEO2 IN
R
L
R
S-VIDEO
AUDIO
S-VIDEO IN
YPbPr2 IN
L
R
R
AUDIO Cable
or
S-VIDEO Cable
GAME CONSOLE
B
AV Cable
A
METHOD A:
Use a composite cable to connect the video camera’s or game console’s composite
video/audio jacks to the LCD TV’s VIDEO2 IN jacks or VIDEO1 IN jacks.
METHOD B:
Use an audio cable to connect the video camera’s or game console’s audio output
jacks to the LCD TV’s audio inputs. Use an S-Video cable to connect the video
camera’s or game console’s s-video output jack to the LCD TV’s S-VIDEO IN input
jack.
Connect all AC power sources, before turning on the power switch of the LCD TV or
other connected equipment.
Press the
button on the remote to turn on the LCD TV.
To watch a video vis camera or game console, press the Input button on the remote to
select VIDEO2/VIDEO1( METHOD A), or VIDEO3 (METHOD B).
Not all cameras have the ability to connect to a TV. Please check your video camera
user guide for compatibility.
21
Chapter 2 Installing the LCD TV
Connecting a DVD Player
Rear of TV
HDMI IN
VGA IN
AUDIO OUT
YPbPr1 IN
AUDIO
AUDIO
Y
Pb
Pr
STEREO
AUDIO
DIGITAL
OPTICAL
HDTV/TV
Air/Cable
L
R
L
R
L
R
L
Y
Pb
Pr
R
L
COAXIAL
AUDIO
VHF/UHF IN
VIDEO
AUDIO
VIDEO2 IN
L
R
S-VIDEO
AUDIO
S-VIDEO IN
L
YPbPr2 IN
R
R
or
Pb
Pr
COMPONENT/AUDIO Cable
AUDIO Cable
S-VIDEO Cable
AV Cable
A
B
C
Pb
Pr
D V D PLA YER
METHOD A:
Use a composite cable to connect the DVD player’s composite video/audio jacks to the
LCD TV’s VIDEO2 IN jacks.
METHOD B:
Use an audio cable to connect the DVD player’s audio output jacks to the LCD TV’s
audio inputs. Use an S-Video cable to connect the DVD player’s s-video output jack
to the LCD TV’s S-VIDEO IN input jack.
METHOD C:
Use a component cable to connect the DVD player’s component output jacks to the LCD
TV’s YPbPr1 IN or YPbPr2 IN input jacks.
Use an audio cable to connect the DVD player’s component audio jacks to the LCD TV’s
audio input jacks.
The component video jacks on your DVD player are sometimes labeled
YPbPr, or YCbCr. For an explanation of component video, see your DVD
player’s user guide.
22
Chapter 2 Installing the LCD TV
Connect all AC power sources, before turning on the power switch of the LCD TV or
other connected equipment.
button on the remote to turn on the LCD TV.
To watch a DVD, press the Input button on the remote to select
VIDEO2( METHOD A), or VIDEO3 ( METHOD B), or VIDEO4/VIDEO5 (METHOD C).
For best picture quality, if your equipment has component video output, use
a component cable instead of a composite video or S-video cable.
23
ENGLISH
Press the
Chapter 2 Installing the LCD TV
Connecting a Digital TV Cable Box or Digital Satellite Receiver
Rear of TV
HDMI IN
VGA IN
AUDIO OUT
YPbPr1 IN
AUDIO
AUDIO
Y
Pb
Pr
STEREO
AUDIO
DIGITAL
OPTICAL
HDTV/TV
Air/Cable
L
R
L
R
L
R
L
Y
Pb
Pr
R
L
COAXIAL
AUDIO
VHF/UHF IN
VIDEO
AUDIO
VIDEO2 IN
L
R
S-VIDEO
AUDIO
S-VIDEO IN
YPbPr2 IN
Pb
L
R
R
Pr
COMPONENT/AUDIO Cable
Pb
Pr
Use a component cable to connect the satellite receiver’s/TV Cable Box’s component
(YPbPr1) output jacks to the LCD TV’s component input jacks.
Use an audio cable to connect the satellite receiver’s/TV Cable Box’s component audio
jacks to the LCD TV’s audio input jacks.
Connect all AC power sources, before turning on the power switch of the LCD TV or
other connected equipment.
Press the
button on the remote to turn on the LCD TV.
To watch programs via satellite receiver or TV Cable Box, press the Input button on the
remote to select VIDEO4/VIDEO5.
24
Chapter 2 Installing the LCD TV
Connecting an AV Equipment with HDMI Connector
Rear of TV
ENGLISH
HDMI IN
VGA IN
AUDIO OUT
YPbPr1 IN
AUDIO
AUDIO
Y
Pb
Pr
STEREO
AUDIO
DIGITAL
OPTICAL
HDTV/TV
Air/Cable
L
R
L
R
L
Y
Pb
Pr
R
L
COAXIAL
AUDIO
VHF/UHF IN
VIDEO
L
AUDIO
VIDEO2 IN
R
L
R
S-VIDEO
AUDIO
S-VIDEO IN
YPbPr2 IN
L
R
R
HDMI Cable
AV EQUIPMENT
Use a HDMI cable to connect the AV equipment’s HDMI output jack to the LCD TV’s HDMI IN
jacks.
Connect all AC power sources, before turning on the power switch of the LCD TV or
other connected equipment.
Press the
button on the remote to turn on the LCD TV.
Press the Input button on the remote to select VIDEO6.
The HDMI connector provides both video and audio signals, it’s not
necessary to connect the audio cable.
25
Chapter 2 Installing the LCD TV
Connecting an AV Equipment with DVI Connector
Rear of TV
HDMI IN
VGA IN
AUDIO OUT
YPbPr1 IN
AUDIO
AUDIO
Y
Pb
Pr
STEREO
AUDIO
DIGITAL
OPTICAL
HDTV/TV
Air/Cable
L
R
L
R
L
Y
Pb
Pr
R
L
COAXIAL
AUDIO
VHF/UHF IN
VIDEO
L
AUDIO
VIDEO2 IN
R
L
R
S-VIDEO
AUDIO
S-VIDEO IN
YPbPr2 IN
L
R
R
AUDIO Cable
AUD IO
L
HDMI-to-DVI Cable
R
DVI IN
AV EQUIPMENT
Use a HDMI-to-DVI cable to connect the AV equipment’s DVI output jack to the LCD TV’s
HDMI IN jacks.
Use an audio cable to connect the AV equipment’s audio output jacks to LCD TV’s HDMI
AUDIO jacks.
Connect all AC power sources, before turning on the power switch of the LCD TV or
other connected equipment.
Press the
button on the remote to turn on the LCD TV.
Press the Input button on the remote to select VIDEO6.
If the LCD TV is connected to AV equipment’s DVI connector, you will need
an HDMI-to-DVI cable or an HDMI adapter(not suplied) and an audio cable.
26
Chapter 3 Using the LCD TV
Connecting a PC
Rear of TV
ENGLISH
HDMI IN
VGA IN
AUDIO OUT
YPbPr1 IN
AUDIO
AUDIO
Y
Pb
Pr
STEREO
AUDIO
DIGITAL
OPTICAL
HDTV/TV
Air/Cable
L
R
L
R
L
Y
Pb
Pr
R
L
COAXIAL
AUDIO
VHF/UHF IN
VIDEO
L
AUDIO
VIDEO2 IN
R
L
R
S-VIDEO
AUDIO
S-VIDEO IN
YPbPr2 IN
L
R
R
AUDIO Cable
VGA Cable
PC
Use a D-SUB cable to connect the PC’s D-SUB output jack to the LCD TV’s VGA input
jack. Use an audio cable to connect the PC’s audio output jacks to LCD TV’s.
Connect all AC power sources, before turning on the power switch of the LCD TV or
other connected equipment.
Press the
button on the remote to turn on the LCD TV.
Press the Input button on the remote to select COMPUTER.
27
Chapter 3 Using the LCD TV
Connecting an Audio Receiver or a Dolby Digital 5.1 Sound System
For better sound quality, you may want to use a Home Theater/Stereo System.
NOTE: If you have a Home Theater/Stereo System that you would like to use with your new Element
Electronics TV, we recommend that you do NOT use your TV’s audio output for this connection.
For the best sound quality, our product testing has shown that you should connect your Home
Theater/Stereo System directly to your A/V device. I.E. You should connect your Home Theater/
Stereo System to your DVD player, Cable/Satellite box or other AV equipment.
Although not recommended, if you prefer to use the TV audio output to make this connection to your
Home Stereo System, please follow the instructions below.
Use an audio cable to connect the audio receiver’s audio LINE IN jacks to LCD TV’s
AUDIO OUT jacks.
Connect all AC power sources, before turning on the power switch of the LCD TV or
other connected equipment.
Press the
button on the remote to turn on the LCD TV.
28
Chapter 3 Using the LCD TV
Chapter 3
USING THE FEATURES
ENGLISH
Wide Screen Viewing
Wide Screen function allows viewing of 4:3/16:9 images in wide screen mode, cycling through
the following wide screen settings. Press the P.SIZE button repeatedly to select the screen
format you want.
FULL
Stretches the image vertically and
horizontally to keeps the image size
consistent in the center of the screen and
stretches the sides
NORMAL is not available when you are
watching 720p, 1080i, or 1080p source.
ZOOM
Stretches the image vertically and
horizontally to fill the screen at 1:2.35
aspect ratio
WIDE
Stretches the image vertically and
horizontally to fill the screen at 1:1.85
aspect ratio
NORMAL
Displays at 4:3 aspect ratio
29
Chapter 3 Using the LCD TV
Operating the Menu
Press the
button to turn the LCD TV on.
Press the MENU button on the remote control,the on-screen menu will appear on the
screen. Use the ◄► buttons to select your main menu option.
VIDEO MENU:
Allows you to make adjustments to your picture settings.
▪ If the signal source is TV/VIDEO/S-VIDEO/YPbPr/
HDMI, the VIDEO MENU appears as:
Picture Mode
Contrast
Brightness
Saturation
Hue
Sharpness
Color Temperature
Noise Reduction
Video
Vivid
▪ If the signal source is VGA, the VIDEO MENU
appears as:
Picture Mode
Contrast
Brightness
Color Temperature
Noise Reduction
VGA
50
54
54
0
5
Vivid
50
54
Medium
Medium
Select
Exit
AUDIO MENU:
Allows you to customize the audio options and effects.
▪ If the signal source is VIDEO/S-VIDEO/YPbPr/
HDMI/VGA, the AUDIO MENU appears as:
Bass
Treble
Balance
Sound Effect
Speaker
Audio
▪ If the signal source is TV, the AUDIO MENU
appears as:
50
50
0
Surround
On
Select
Exit
30
Bass
Treble
Balance
Sound Effect
MTS
SPDIF Type
Audio Language
Speaker
50
50
0
Surround
Stereo
Dolby Digital
English
On
Audio
Select
Exit
Chapter 3 Using the LCD TV
TV MENU:
Allows you to edit and label channels.
ENGLISH
Channel Scan
Tuner Mode
Channel Skip
Time Zone
Cable
Eastern Time
TV
Select
Exit
SETUP MENU:
Allows you to set up a variety of features: Language, Closed Caption, factory reset, Parental Control sleep
timer.
OSD Language
Closed Caption
Parental
Gamma
Reset Default
English
Middle
Use the ▲▼ buttons to highlight the option of the sub-menu, and press the OK
button. While in adjustment mode, and use the ◄► buttons to change the value of
the item.
Press the EXIT button to exit the menu.
31
Chapter 3 Using the LCD TV
Customizing the VIDEO Settings
Press the
button to turn the LCD TV on.
Press the MENU button on the remote control to display the Main menu, and use the
◄► buttons to select the VIDEO.
Use the ▲▼buttons to highlight an individual VIDEO option, use the ◄► buttons to
change the setting, and press the MENU to exit the menu
Picture Mode
Contrast
Brightness
Saturation
Hue
Sharpness
Color Temperature
Noise Reduction
Video
Vivid
50
54
54
0
5
or
Picture Mode
Contrast
Brightness
Color Temperature
Noise Reduction
VGA
Vivid
50
54
Medium
Medium
Select
Exit
Video
Select
Exit
The VIDEO menu includes the following options:
Picture Mode
Cycles among display types: Vivid/Hi-Bright/Cinema/Sport/User
Contrast
Controls the difference between the brightest and darkest regions of
the picture
Brightness
Controls the overall brightness of the picture
Saturation
Controls the color intensity
Hue
Controls the difference between the green and red regions of the
picture
Sharpness
Increase this setting to see crisp edges in the picture; decrease it for
soft edges
32
Chapter 3 Using the LCD TV
Color temperature
Color Temperature
R Gain
G Gain
B Gain
User
120
120
120
Noise Reduction
Select to reduce the noise level of connected equipment: Off/Low/
Strong /Medium.
VGA
Press the OK button to enter the VGA Setting:
Auto Setting
H.Position
V. Position
Clock
Phase
VGA
72
31
127
Enter
Select
Exit
▪ Auto Setting
Press the OK button to automatically adjust the
display settings to optimize performance based on
the VGA mode
▪ H. Position
Adjusts the position of the picture left and right in the
window
▪ V. Position
Adjusts the position of the picture up and down in the
window
▪ Clock
Controls the width of the picture based on the VGA
mode
▪ Phase
Controls the signal phase, which can improve focus
clarity and image stability based on the VGA mode
33
ENGLISH
Adjusts color components independently to achieve a warm or cool
effect: Cool/Nature/Warm/User
▪ Warm:
Increases red tint
▪ Nature : Increases natural tint
▪ Cool :
Increases blue tint
▪ User :
Allows the user to adjust red, green and blue color
component levels independently.
Chapter 3 Using the LCD TV
Customizing the AUDIO Settings
Press the
button to turn the LCD TV on.
Press the MENU button on the remote control to display the Main menu, and use the
◄► buttons to select the AUDIO.
Use the ▲▼buttons to highlight an individual AUDIO option, use the ◄► buttons to
change the setting, and press the MENU to exit the menu
Bass
Treble
Balance
Sound Effect
Speaker
50
50
0
Surround
On
or
Bass
Treble
Balance
Sound Effect
MTS
SPDIF Type
Audio Language
Speaker
50
50
0
Surround
Stereo
Dolby Digital
English
On
The AUDIO menu includes the following options:
Bass
Controls the relative intensity of lower-pitched sounds
Treble
Controls the relative intensity of higher pitched sounds
Balance
Adjusts the relative volume of the speakers in a multiple speaker
system
Sound Effect
Allows selection of an audio-enhancement technique from among the
following options: Surround/Live/Dance/Techno/Classic/Soft/Rock/
POP/Off
MTS
Allows you to listen to high-fidelity stereo sound while watching TV
▪ Stereo:
Use separate audio tracks for left and right speakers, if available
▪ SAP:
You can enjoy a second audio program from the speakers while
watching a scene in the original program
▪ Mono:
Allows mono output (useful when stereo is noisy or inconsistent)
34
Chapter 3 Using the LCD TV
SPDIF Type
Allows to selection of the digital sound format: PCM/OFF/Dolby
Digital
▪ Dolby Digital:
The external audio system is connected to the AUDIO OUT
DIGITAL (OPTICAL or COAXIAL) ot the LCD TV
▪ OFF:
Select OFF to turn off the external audio system
Audio Language
Allows to select the audio language:English/Spanish/French.
Speaker
Allows to select to turn on or off the TV speakers.
35
ENGLISH
▪ PCM:
The external audio system is connected to the AUDIO OUT (L/R)
of the LCD TV
Chapter 3 Using the LCD TV
Customizing the TV Settings
Press the
button to turn the LCD TV on.
Press the MENU button on the remote control to display the Main menu, and use the
◄► buttons to select the TV.
Use the ▲▼buttons to highlight an individual TV option, use the ◄► buttons
changes the setting, and press the MENU exits the menu.
Channel Scan
Tuner Mode
Channel Skip
Time Zone
TV
Cable
Eastern Time
Select
Exit
The TV menu includes the following options:
Channel Scan
Press the OK button, the Channel Scanning automatically creates a
list of receivable channels.
Tuner Mode
Allows selection between CATV cable and antenna signal sources:
▪ AIR
Choose this setting if you are receiving TV channels with an antenna
(over the air)
▪ Cable
Choose this setting if you are receiving TV channels with a CATV
(cable TV)
Channel Skip
Allows addition/removal of channels on the channel list.
Press the OK button to display the Channel Skip menu:
2 ABC
Analog
3 DISC
Analog
4
Analog
5
Analog
6
Analog
7
Analog
8
Analog
9
Analog
10
Analog
Channel Skip
Select
36
Back
Chapter 3 Using the LCD TV
Press the ▼ button to select the desired channel, andpress the
OK button repeatedly to select show ( ) or hide( )
Select Favorite List from the TV option and press the OK button.
The Favorite List menu appears:
2 ABC
Analog
3 DISC
Analog
4
Analog
5
Analog
6
Analog
7
Analog
8
Analog
9
Analog
10
Analog
Press the ▼ button to select the desired channel, and press
the OK button repeatedly to select show ( ) or hide( )
Time Zone
Allows selection of regional TV systems of USA: Eastern Time/
Indiana/Central time/Mountain Time/Arizona/Pacific Time/Alaska/
Hawaii
37
ENGLISH
Favorite List
Chapter 3 Using the LCD TV
Customizing the SETUP Settings
Press the
button to turn the LCD TV on.
Press the MENU button on the remote control to display the Main menu, and use the
◄► buttons to select the SETUP.
Use the ▲▼ buttons to highlight an individual SETUP option, use the ◄► buttons to
change the setting, and press the MENU to exit the menu.
OSD Language
Closed Caption
Parental
Gamma
Reset Default
English
Middle
The SETUP menu includes the following options:
OSD Language
Selects to display all on-screen menus in your language of choice:
English/French/Spanish
Closed Caption
Allows to select from analog or digital closed caption modes and
press the OK button. The Closed Caption list appears:
Analog Cloaed Caption
Digital Cloaed Caption
Digital Caption Style
Off
Off
Analog Closed Caption:
Press the ◄► buttons to select the basic analog closed caption
options: OFF/CC1/CC2/CC3/CC4
▪ CC1 /CC2 /CC3 /CC4:
Display a printed version of the dialog and sound effects of the
program being viewed
▪ T1/T2:
Display station information presented using either half or the
whole screen
▪ T3/T4:
Extended Data Services. For example: Network name, program
name, program length, etc.
38
Chapter 3 Using the LCD TV
Digital Closed Caption:
Press the ◄► buttons to select the digital closed caption options:
Service1/Service2/Service3/Service4/Service5/Service6/OFF
Caption Style:
Press OK button to customize the settings for digital closed
caption option:
Custom
Caption Style
Font Size
Font Color
Font Opacity
Background Color
Background Opacity
Window Color
Window Opacity
Parental
Large
White
Solid
Black
Solid
Black
Translucent
The Parental Control can be set up to the TV to block Channel,
Video Source and to change password.
Use the ▼ button to select the Parental, and press the OK to
display the Parental menu
Use the Program Block function, must enter a four-digit
password. The factory password is 0000
The Parental list appears:
Program Block
Allows to setup the TV and MPAA Rating
Lock options (refer to “Using the Program
Block Setting”).
U.S.TV Ratings
U.S. Movie Ratings
Canadian English Ratings
Canadian French Ratings
Block MPAA Unrated
Block TV Unrated
39
NO
NO
ENGLISH
Note: The setting here will be applied to each DTV channel
Chapter 3 Using the LCD TV
Allows to block digital channels.
Channel Block
2 ABC
Analog
3 DISC
Analog
4
Analog
5
Analog
6
Analog
7
Analog
8
Analog
9
Analog
10
Analog
Channel Block
Select
Back
Selects to block a Input source signal
Input Block
1
TV(CABLE/AIR)
2
VIDEO1 (SIDE)
3
VIDEO2 (REAR)
4
VIDEO3 (S-VIDEO)
5
VIDEO4 (YPbPr1)
6
VIDEO5 (YPbPr2)
7
VIDEO6 (HDMI1)
8
COMPUTER(VGA)
Input Block
Change Password
Select
Back
Selects to change your password
Gamma
Allows adjustment of the display’s gamma correction, which fine
tunes both brightness and red/green/blue ratios: Bright/Dark/Middle.
Reset Default
Press the OK button to restore factory settings
40
Chapter 3 Using the LCD TV
Using the Program Block Settings
Use the ▼ buttons to highlight Parental, and press the OK button.
OSD Language
Closed Caption
Parental
Gamma
Reset Default
English
Middle
Use the Parental function, must enter a four-digit password. The factory password is
0000.
Password
****
Program Block
Channel Block
Input Block
Change Password
Use the ▼ button to select the Program Block, and press the OK to display the
Program Block menu.
U.S.TV Ratings
U.S. Movie Ratings
Canadian English Ratings
Canadian French Ratings
Block MPAA Unrated
Block TV Unrated
NO
NO
41
ENGLISH
Press the MENU button on the remote control to display the Main menu, and use the
◄► buttons to select the SETUP.
Chapter 3 Using the LCD TV
The Parental block menu includes the following options:
U.S. TV Ratings
Selects to activate the TV Rating programs.
U.S. Movie Ratings
Selects to activate the MPAA Rating programs
Canadian English Ratings
Selects to activate the English Rating programs of Canada.
Canadian French Ratings
Selects to activate the French Rating programs of Canada
Block MPAA Unrated
▪ YES:
Block all movies that are broadcast without a MPAA rating.
▪ NO:
Allows all movies that are broadcast without a MPAA rating
Block TV None Rating
▪ YES:
Block all movies that are broadcast without a TV rating.
▪ NO:
Allows all movies that are broadcast without a TV rating.
42
Chapter 3 Using the LCD TV
U.S. TV Ratings
The U.S.TV Rating has 2 rating methods: Content-Based Rating and Age-Based Rating.
The U.S.TV Rating includes the following options:
D
L
S
V
ENGLISH
A
FV
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
Allowed Rating
Blocked Rating
AGE-BASED
RATING
DESCRIPTION
TV-Y
All children
TV-Y7
Directed to children age 7 and older
TV-G
General Audience
TV-PG
Parental Guidance suggested
TV-14
Parents strongly cautioned
TV-MA
Mature Audience only
CONTENT-BASED
RATING
DESCRIPTION
FV
Fantasy violence
D
Suggestive dialogue
L
Strong language
S
Sexual situations
V
Violence
ALL
All contents are blocked
CONTENT-BASED
FV
D
L
S
V
AGE-BASED
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
: To block programs by both content and age.
Use the ◄►▲▼ buttons to select the rating you want and press the OK button repeatedly to
select BLOCK or UNBLOCK .
43
Chapter 3 Using the LCD TV
Canadian English Ratings
The Canadian Englsh Ratings includes the following options:
G
C8+
G
PG
14+
18+
Blocked Rating
Allowed Rating
Canadian English Ratings
Select
RATING
DESCRIPTION
G
All children
Back
C8+
Children 8 years and older
G
General programming
PG
Parental guidance
14+
Viewers 14 and older
18+
Adult programming
Use the ◄►▲▼ buttons to select the rating you want and press the OK button repeatedly to
select BLOCK or UNBLOCK .
Canadian French Ratings
The Canadian French Ratings includes the following options:
G
8 ans+
13 ans+
16 ans+
18 ans+
Allowed Rating
Canadian English Ratings
Blocked Rating
Select
Back
RATING
DESCRIPTION
G
General programming
8 ans+
Not recommended for ages under 8
13 ans+
Not recommended for ages under 13
16 ans+
Not recommended for ages under 16
18 ans+
Programming restricted to adults.
Use the ◄►▲▼ buttons to select the rating you want and press the OK button repeatedly to
select BLOCK or UNBLOCK .
44
Specifications
U.S. Movie Ratings
G
PG
PG-13
R
NC-17
X
Allowed Rating
U.S. Movie Ratings
Blocked Rating
Select
Back
RATING
DESCRIPTION
G
General Audiences. Movie is appropriate for all ages
PG
Parental Guidance Suggested. May contain material not suited for younger
viewers
PG-13
Contains content that may not be appropriate for viewers under the age of
13
R
Restricted. Contains adult content, no one under 17 admitted without
parent
NC-17
No one 17 and under admitted
X
No one 17 and under admitted
Use the ◄►▲▼ buttons to select the rating you want and press the OK button repeatedly to
select BLOCK or UNBLOCK .
45
ENGLISH
The U.S. Movie Ratings is used for original movies rated by the Motion Picture Association of
America(MPAA) as broadcasted on cable TV and not edited for television.
The U.S. Movie Ratings includes the following options:
Chapter 3 Using the LCD TV
Using the Program Guide
The Program Guide feature brings all sorts of information to your screen, such as program title,
program duration, time remaining, rating information, closed caption, availability, etc.
With the LCD TV connected to a television programming source, press the INPUT button
on the remote control and use the ▲▼ buttons to select TV and press the OK button.
Press the GUIDE button on the remote control, the Program Guide will appear on the
screen:
Monday 15 January 2007 2:36:26 PM
3-1
7-2 KQED-SD
7-2
Today
7:00 PM
EYEWITHNESS NEWS 4PM
cc
Today
7:30 PM
ABC WORLD NEWS
cc
Today
9:30 PM
ABC’S MONDAY NIGHT FOOTBALL
cc
SPORTSZONE
cc
Tomorrow
12:30 AM
Press the ◄► button to select the channel.
Press the ▲▼ button to select the program from a list, the Program Guide provides
introduction about the current program being shown on each channel.
The Program information in the guide is provided by the broadcasters. It may sometimes
include only the channel number, without a program title or description.
Monday 15 January 2007 2:36:26 PM
3-1
7-2 KQED-SD
7-2
Today
7:00 PM
EYEWITHNESS NEWS 4PM
cc
Today
7:30 PM
ABC WORLD NEWS
cc
9:30 PM
ABC’S MONDAY NIGHT FOOTBALL
cc
SPORTSZONE
cc
Today
Tomorrow
12:30 AM
TV-PG
5:00 PM - 5:30 PM Mon, 20 Jan.
EYEWITHNESS NEWS
Press the GUIDE button again on the remote control to exit the Program Guide
46
Specifications
SPECIFICATIONS
MODEL
Panel Size
FLX-3210
32” TFT LCD
Brightness
500 cm2
400 cm2
Contrast Ratio
800:1
1200:1
Max. Resolution
Input Connector
FLX-2610
26” TFT LCD
1366x768
1366x768
VIDEO/AUDIO(L/R)
2
2
S-VIDEO/AUDIO(L/R)
1
1
YPbPr/AUDIO(L/R)
2
2
VGA/AUDIO(L/R)
1
1
HDMI/AUDIO(L/R)
1
1
AUDIO OUT(L/R)
1
1
OPTICAL/COAXIAL
1
1
HEADPHONE
1
1
ENGLISH
LCD Panel
Power Source
AC100~240V, 50/60HZ, 2.2A AC100~240V, 50/60HZ, 2.2A
Power Consumption
180 W, standby < 5 W
180 W, standby < 5 W
Dimension
26.7 w x 22.1 h x 7.9 d inch
31.7 w x 25.0 h x 8.4 d inch
WEIGHT
31.97 LB
39.5 LB
MODEL
LCD Panel
Panel Size
37” TFT LCD
Brightness
500 cm2
Contrast Ratio
Max. Resolution
Input Connector
FLX-3710
800:1
1366x768
VIDEO/AUDIO(L/R)
2
S-VIDEO/AUDIO(L/R)
1
YPbPr/AUDIO(L/R)
2
VGA/AUDIO(L/R)
1
HDMI/AUDIO(L/R)
1
AUDIO OUT(L/R)
1
OPTICAL/COAXIAL
1
HEADPHONE
1
Power Source
AC100~240V, 50/60HZ, 3.0A
Power Consumption
275 W, standby < 8 W
Dimension
36.6 w x 28.2 h x 9.4 d inch
WEIGHT
54 LB
20070228
47
Download PDF