Yamaha ATS-1050 Quick start guide

ATS-1050 Quick Start Guide
U
Supplied items
Before assembling and connecting, make sure you have received all of the following items.
If anything is missing, please call 888-892-6242, 8AM to 5PM PST Monday through Friday.
Sound bar (ATS-1050)
Mounting template
(Use when attaching the sound bar to a wall.)
Remote control
Battery
(AAA, R03, UM4) × 2
Optical cable
1.5 m (4.9 ft)
3.5 mm stereo mini plug cable
Spacer × 2
(Use when attaching the
1.5 m (4.9 ft)
Owner’s Manual
(This sheet)
sound bar to a wall.)
(Install the batteries in the
remote control.)
Quick Start Guide
Placement
On a TV cabinet, etc.
Attaching to a wall
Remote control
sensor (top panel)
Installation position Remote control
sensor (front panel)
selector switch
(bottom panel)
© 2015 Yamaha Corporation
Keys
Installation position
selector switch
(bottom panel)
Place the sound bar in front of or below your TV, at least 50 mm
(2") away from your TV.
The sound bar may also be attached to a wall, using the
included mounting template and commercially available
screws. Refer to the Owner’s Manual for additional installation
instructions.
Set the installation position selector switch according to
the installation position of the sound bar. The sound quality
appropriate to the installation position will be set.
NOTE
• Be careful not to stack the sound bar with any other components, as
vibration may cause system disruption in other components.
Continued to the reverse side
Printed in Indonesia
ZR10560
Watching TV
Connections
1.
3.
Connect the TV and sound bar with the
optical cable (supplied).
Remove the cap of the optical cable and check the
direction of the plug.
2.
4.
Turn on the TV and set the volume to
minimum.
Disable the TV speakers using the TV’s audio
settings menu (if available).
HINT
Connect the power cable of the sound bar to
AC wall outlet.
If a setting to disable the speaker output is not available on
your TV, you may disable it by connecting headphones to the
headphone jack on the TV. For details, refer to the instruction
manual of the TV.
Sound bar (rear)
Connect to an AC wall
outlet. Leave the unit
powered off until all
connections are complete.
TV
BD/DVD
For details, refer to the Owner’s Manual.
1. Press
to turn on the sound bar.
2. Press the TV key to select TV as the input source.
3. Select the desired input source on the TV.
4. Press the VOLUME (+/–) keys to adjust the
volume.
Playback of a Bluetooth® device
You can connect a Bluetooth device, such as a smartphone or
digital music player, with the sound bar wirelessly. For details,
refer to the Owner’s Manual.
ANALOG SUBWOOFER OUT
HINT
Optical cable
(supplied)
OPTICAL OUTPUT
In the following cases, connect the coaxial digital
audio output of the playback device to the BD/DVD
input of the sound bar with a coaxial digital cable
(commercially available), then select the BD/DVD key
on the remote control for the input source.
–The TV does not have an optical output.
–The TV does not output audio (or outputs low volume
audio) from the connected playback device.
–The audio from the playback device connected to
the TV cannot be heard as surround sound.
TV
Set top box or playback device
(such as a Blu-ray DiscTM player)
... and more features!
For details about the other useful features, refer to the
Owner’s Manual.
–– “HOME THEATER CONTROLLER” sound bar control app
–– TV’s remote control learning function
–– Clear voice
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Yamaha Corporation is under
license.
Blu-ray Disc is a trademark of the Blu-ray Disc Association.

Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project