advertisement
BF2D
Owner’s Manual
31ZW6610
00X31-ZW6-6100
N
BF2D6
2eY11000.2005.12
Printed in Japan ©2005 Honda Motor Co., Ltd. -All Rights Reserved
PANTONE 288 CVC DIC F101 BLACK
2006
05/12/21 14:01:07 31ZW6601_001
The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
Keep this owner’s manual handy, so you can refer to it at any time. This owner’s manual is considered a permanent part of the outboard motor and should remain with the outboard motor if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Honda Motor Co., Ltd. reserves the right, however, to discontinue or change specifications or design at any time without notice and without incurring any obligation whatever. No part of this publication may be reproduced without written permission.
05/12/21 14:01:13 31ZW6601_002
Congratulations on your selection of a Honda outboard motor. We are certain you will be pleased with your purchase of one of the finest outboard motors on the market.
We want to help you get the best results from your new outboard motor and to operate it safely. This manual contains information on how to do that; please read it carefully.
As you read this manual you will find information preceded by a symbol. That information is intended to help you avoid damage to your outboard motor, other property, or the environment.
We suggest you read the warranty policy to fully understand its coverage and your responsibilities of ownership.
When your outboard motor needs scheduled maintenance, keep in mind that your Honda marine dealer is specially trained in servicing Honda outboard motors. Your Honda marine dealer is dedicated to your satisfaction and will be pleased to answer your questions and concerns.
Best Wishes,
Honda Motor Co., Ltd.
INTRODUCTION
1
05/12/21 14:01:23 31ZW6601_003
INTRODUCTION
A FEW WORDS ABOUT
SAFETY
Your safety and the safety of others are very important. And using this outboard motor safely is an important responsibility.
To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others.
Of course, it is not practical or possible to warn you about all the hazards associated with operating or maintaining an outboard motor. You must use your own good judgment.
You will find important safety information in a variety of forms, including:
Safety Labels − on the outboard motor.
Safety Messages − preceded by a safety alert symbol three signal words, DANGER, WARNING, or CAUTION.
and one of
These signal words mean:
You WILL be KILLED or SERIOUSLY
HURT if you don’t follow instructions.
You CAN be KILLED or SERIOUSLY
HURT if you don’t follow instructions.
You CAN be HURT if you don’t follow instructions.
Safety Headings − such as IMPORTANT SAFETY INFORMATION.
Safety Section − such as OUTBOARD MOTOR SAFETY.
Instructions − how to use this outboard motor correctly and safely.
This entire book is filled with important safety information − please read it carefully.
2
05/12/21 14:01:27 31ZW6601_004
CONTENTS
OUTBOARD MOTOR SAFETY ...................................
IMPORTANT SAFETY INFORMATION ................
. 6
SAFETY LABEL LOCATIONS ................................
. 8
CONTROLS AND FEATURES ....................................
CONTROLS AND FEATURE
IDENTIFICATION CODES ..................................
. 9
COMPONENT AND CONTROL LOCATIONS ....
. 10
CONTROLS ..............................................................
. 11
Engine Stop Switch and Switch Clip ....................
. 11
Choke Knob .........................................................
. 11
Throttle Lever (SCAB type) .................................
. 12
Throttle Grip (SHA/SCHA/LCHA type) ..............
. 12
Throttle Friction Knob
(SHA/SCHA/LCHA type) ................................
. 12
Fuel Valve Lever ...................................................
. 13
Recoil Starter Grip ................................................
Engine Cover Retaining Strap .............................
. 13
. 13
Transom Angle Adjusting Bolt .............................
. 14
Tilt Lever ...............................................................
. 14
Steering Friction Bolt ............................................
. 15
Clamp Screws ........................................................
. 15
Fuel Cap Vent Knob .............................................
. 15
OTHER FEATURES ................................................
. 16
Centrifugal Clutch (SCHA/LCHA type) ..............
. 16
Oil Level Inspection Window ...............................
. 16
Anode ....................................................................
. 16
INSTALLATION ..........................................................
POWER REQUIREMENTS .....................................
. 17
INSTALLATION POSITION
ATTACHMENT
..................................
.......................................................
. 17
. 18
TRANSOM ANGLE ADJUSTMENT .....................
. 19
BEFORE OPERATION ................................................
ARE YOU READY TO GET UNDER WAY ？ .....
. 20
IS YOUR OUTBOARD MOTOR
READY TO GO ？ ................................................
. 20
3
05/12/21 14:01:30 31ZW6601_005
CONTENTS
OPERATION ................................................................
SAFE OPERATING PRECAUTIONS ....................
. 22
BREAK-IN PROCEDURE .......................................
. 22
TRANSOM ANGLE ADJUSTMENT
STARTING THE ENGINE
.....................
......................................
. 22
. 23
EMERGENCY STARTING .....................................
. 26
STOPPING THE ENGINE .......................................
. 28
Emergency Engine Stopping ................................
. 28
Normal Engine Stopping .......................................
. 28
THROTTLE OPERATION ......................................
REVERSING THE OUTBOARD MOTOR ............
. 30
. 31
STEERING
CRUISING
...............................................................
. 32
................................................................
. 33
MOORING, BEACHING, LAUNCHING ...............
. 34
SERVICING YOUR OUTBOARD MOTOR ..............
THE IMPORTANCE OF MAINTENANCE ...........
. 36
MAINTENANCE SAFETY .....................................
TOOL KIT AND EMERGENCY STARTER
. 37
ROPE .....................................................................
. 38
MAINTENANCE SCHEDULE ...............................
ENGINE COVER REMOVAL AND
. 39
INSTALLATION ..................................................
. 41
Engine Oil Level Check ........................................
. 41
Engine Oil Change ................................................
Engine Oil Recommendations ..............................
. 41
. 42
Gear Oil Change ....................................................
. 43
Lubrication Points
Spark Plug Service
.................................................
. 44
................................................
. 45
REFUELING .............................................................
. 47
FUEL RECOMMENDATIONS ...............................
. 48
Recoil Starter Rope Inspection
Anode Replacement
.............................
..............................................
. 49
. 49
Propeller Replacement ..........................................
. 50
4
05/12/21 14:01:33 31ZW6601_006
CONTENTS
STORAGE ....................................................................
STORAGE PREPARATION ...................................
. 51
Cleaning ................................................................
. 51
Fuel ........................................................................
. 51
Adding a Fuel Stabilizer .......................................
. 52
Draining the Fuel Tank and Carburetor ................
. 52
Engine Oil .............................................................
STORAGE PRECAUTIONS ...................................
. 53
. 53
REMOVAL FROM STORAGE ...............................
. 54
TRANSPORTING ........................................................
WITH OUTBOARD MOTOR INSTALLED
ON BOAT .............................................................
. 55
WITH OUTBOARD MOTOR REMOVED
FROM BOAT .......................................................
. 55
TAKING CARE OF UNEXPECTED PROBLEMS ....
ENGINE WILL NOT START ..................................
. 56
HARD STARTING OR STALLS AFTER
STARTING ...........................................................
. 58
SUBMERGED MOTOR ..........................................
. 60
TECHNICAL INFORMATION ...............................
. 62
Serial Number Locations ......................................
Carburetor Modification for High Altitude
. 62
Operation ...........................................................
. 63
Oxygenated Fuels ..................................................
. 64
Emission Control System Information
Star Label
.................
..............................................................
. 65
. 67
Specifications ........................................................
CONSUMER INFORMATION ...............................
. 69
. 70
Honda Publications ...............................................
. 70
Customer Service Information ..............................
. 70
Distributor’s Limited Warranty ............................
Emission Control System Warranty .....................
. 73
. 77
WIRING DIAGRAM ....................................................
INDEX ...........................................................................
5
05/12/21 14:01:42 31ZW6601_007
OUTBOARD MOTOR SAFETY
IMPORTANT SAFETY
INFORMATION
The Honda BF2D outboard motor is designed for use with boats that have a suitable manufacturer’s power recommendation. Other uses can result in injury to the operator or damage to the outboard motor and other property.
Most accidents can be prevented if you follow all instructions in this manual and on the outboard motor.
The most common hazards are discussed below, along with the best way to protect yourself and others.
Operator Responsibility
It is the operator’s responsibility to provide the necessary safeguards to protect people and property.
Know how to stop the engine quickly in case of emergency.
Understand the use of all controls.
Stop the engine immediately if anyone falls overboard, and do not run the engine while the boat is near anyone in the water.
Always stop the engine if you must leave the controls for any reason.
Attach the emergency stop switch lanyard securely to the operator.
Always wear a PFD (Personal
Flotation Device) while on the boat.
Familiarize yourself with all laws and regulations relating to boating and the use of outboard motors.
Be sure that anyone who operates the outboard motor receives proper instruction.
Be sure the outboard motor is properly mounted on the boat.
Do not remove the engine cover while the engine is running.
6
05/12/21 14:01:47 31ZW6601_008
Refuel With Care
Gasoline is extremely flammable, and gasoline vapor can explode.
Refuel outdoors, in a wellventilated area, with the engine stopped. Never smoke near gasoline, and keep other flames and sparks away.
Refuel carefully to avoid spilling fuel. Avoid overfilling the fuel tank.
After refueling, tighten the filler cap securely. If any fuel is spilled, make sure the area is dry before starting the engine.
OUTBOARD MOTOR SAFETY
Carbon Monoxide Hazard
Exhaust gas contains poisonous carbon monoxide. Avoid inhalation of exhaust gas. Never run the engine in a closed garage or confined area.
7
05/12/21 14:01:56 31ZW6601_009
OUTBOARD MOTOR SAFETY
SAFETY LABEL LOCATIONS
The labels shown here contain important safety information. Please read them carefully. These labels are considered permanent parts of your outboard motor. If a label comes off or becomes hard to read, contact an authorized Honda marine dealer for a replacement.
8
05/12/21 14:02:06 31ZW6601_010
CONTROLS AND FEATURES
CONTROL AND FEATURE IDENTIFICATION CODES
Model BF2D
Type SHA SCHA
S
Shaft Length
L
Throttle Grip
Centrifugal Clutch
Refer to this chart for an explanation of the Type Codes used in this manual to identify control and feature applications.
TYPE CODE(example)
S C H A
Destination
A=America
Throttle type
H=Throttle grip
None=Throttle lever
Centrifugal clutch
C=With centrifugal clutch
None=Without centrifugal clutch
Shaft length
S=Short shaft
L=Long shaft
LCHA
9
05/12/21 14:02:12 31ZW6601_011
CONTROLS AND FEATURES
COMPONENT AND CONTROL LOCATIONS
THROTTLE LEVER
(SCAB type)
ENGINE STOP SWITCH
STARTER GRIP ENGINE COVER CASE PROTECTOR
FUEL FILLER CAP
OIL FILLER CAP
(inside the engine cover)
OIL LEVEL INSPECTION
WINDOW
CHOKE KNOB
THROTTLE GRIP
(SHA/SCHA/LCHA type)
TILLER HANDLE
EMERGENCY ENGINE
STOP SWITCH LANYARD
CLAMP SCREW
ADJUSTING BOLT
AND WING NUT
FUEL VALVE LEVER
ENGINE COVER
RETAINING STRAP
STEERING
FRICTION BOLT
ANODE METAL
THROTTLE GRIP
FRICTION KNOB
(SHA/SCHA/LCHA type)
TILT LEVER
GEAR OIL LEVEL PLUG
ANTIVENTILATION
PLATE
STERN BRACKET
GEAR OIL DRAIN/FILL PLUG
LCHA type is shown
10
PROPELLER
05/12/21 14:02:22 31ZW6601_012
CONTROLS
Engine Stop Switch and Switch
Clip
ENGINE STOP SWITCH
LANYARD
SWITCH CLIP
SWITCH CLIP
The engine stop switch controls normal engine stopping and emergency engine stopping.
The switch clip must be inserted in the engine stop switch in order for the engine to start and run. The lanyard should be attached to the operator’s PFD (Personal Flotation
Device) or worn around the wrist as
When used as described, the engine stop switch and lanyard system stops the engine if the operator falls away from the controls.
A spare switch clip is supplied with the tool kit.
CONTROLS AND FEATURES
Choke Knob
O F F
CHOKE KNOB
O N
The choke knob opens and closes the choke valve in the carburetor.
The ON position enriches the fuel mixture for starting a cold engine.
The OFF position provides the correct fuel mixture for operation after starting, and for restarting a warm engine.
LANYARD
11
05/12/21 14:02:32 31ZW6601_013
CONTROLS AND FEATURES
Throttle Lever
(SCAB type)
The throttle lever controls engine speed.
An index mark on the engine cover shows throttle position and is helpful for setting the throttle correctly when
Throttle Grip
(SHA/SCHA/LCHA type)
THROTTLE GRIP
FAST
SLOW
THROTTLE LEVER
SLOW
The throttle grip controls engine speed.
An index mark on the tiller arm shows throttle position and is helpful for setting the throttle correctly when
FAST
Throttle Friction Knob
(SHA/SCHA/LCHA type)
THROTTLE GRIP FRICTION KNOB
RELEASE
FIX
The throttle friction knob adjusts resistance to throttle grip rotation.
Turn the knob clockwise to increase friction for holding a throttle setting while cruising.
Turn the knob counterclockwise to decrease friction for easy throttle grip rotation.
12
05/12/21 14:02:39 31ZW6601_014
Fuel Valve Lever
FUEL VALVE LEVER
Recoil Starter Grip
RECOIL STARTER GRIP
CONTROLS AND FEATURES
Engine Cover Retaining Strap
ENGINE COVER
ON OFF
STRAP
The fuel valve opens and closes the passage between the fuel tank and the carburetor.
The fuel valve lever must be in the
ON position for the engine to run.
When the engine is not in use, leave the fuel valve lever in the OFF position to prevent carburetor flooding and to reduce the possibility of fuel leakage.
Pull the starter grip to operate the recoil starter for starting the engine.
Use the retaining strap to hold the engine cover closed. Do not remove the engine cover while the engine is running.
13
05/12/21 14:02:47 31ZW6601_015
CONTROLS AND FEATURES
Transom Angle Adjusting Bolt Tilt Lever
REAR CARRYING HANDLE
ADJUSTING BOLT AND WING NUT
The transom angle adjusting bolt is used to adjust the angle of the outboard motor in the normal
operating position (see page 22
).
Loosen the wing nut to free the adjusting bolt.
Adjust the angle of the outboard motor, and tighten the wing nut. Be sure that the bolt head and wing nut are seated in one of the four recesses in the adjustment slot.
14
FRONT
CARRYING
HANDLE
75°
The tilt lever enables the outboard motor to be tilted for beaching, launching, or mooring.
Tilt the outboard motor by holding the carrying handles, as shown. The spring-loaded tilt lever will automatically move into position and hold the outboard motor when it reaches approximately 75°.
TILT LEVER
To return the outboard motor to the normal running position, hold the outboard motor and pull the tilt lever, then slowly lower the outboard motor.
05/12/21 14:02:56 31ZW6601_016
Steering Friction Bolt
STEERING FRICTION BOLT
Clamp Screws
CLAMP SCREWS
CONTROLS AND FEATURES
Fuel Cap Vent Knob
VENT KNOB
OPEN
T O I N C R E A S E
F R I C T I O N
T O D E C R E A S E
F R I C T I O N
The steering friction bolt adjusts steering resistance.
Less friction allows the outboard motor to turn more easily. More friction helps to hold steady course while cruising or to prevent the outboard motor from swinging while trailering the boat.
Use the clamp screws to secure the outboard motor to the transom.
FUEL FILLER CAP
The cap is provided with a vent knob to seal the fuel tank. Open the vent knob 2 or 3 turns before starting the
15
05/12/21 14:03:04 31ZW6601_017
CONTROLS AND FEATURES
Oil Level Inspection Window OTHER FEATURES
Centrifugal Clutch (SCHA/
LCHA type)
The centrifugal clutch automatically engages and transmits power when engine speed is increased above approximately 2,700 rpm. At idle speed, the clutch is disengaged.
U P P E R L I M I T
L O W E R L I M I T
Anode
Short shaft type Long shaft type
OIL LEVEL INSPECTION WINDOW
Use the oil level inspection window to check the engine oil level with the engine stopped and the outboard motor in the upright position.
ANODE
The anode is made of a sacrificial material that helps to protect the outboard motor from corrosion.
16
05/12/21 14:03:14 31ZW6601_018
Correct and secure installation is essential for safe boating and good performance. Follow the installation instructions provided in this manual.
POWER REQUIREMENTS
Before installation, check to be sure that the outboard motor does not exceed the recommended maximum horsepower for the boat on which it is to be installed. Refer to the boat’s certification plate for recommended maximum horsepower. If the certification plate information is not available, contact the boat dealer or manufacturer.
For most applications, the outboard motor should have a horsepower rating which provides 80% of the maximum recommended horsepower for the boat.
INSTALLATION POSITION
CENTER LINE
Install the outboard motor on the center of the boat transom.
INSTALLATION
Install the engine so the antiventilation plate is at or slightly below the bottom of the boat. When the boat is in the water and normally loaded, make sure the antiventilation plate is at least 6 in (150 mm) below the surface of the water. If your installation does not meet both these conditions, see your Honda marine dealer for advice.
The correct dimensions differ according to the type of the boat and the configuration of the bottom of the boats. Follow the manufacture’s recommended installation height.
WATER
SURFACE
T R A N S O M
H E I G H T
ANTIVENTILATION
PLATE
Type:
S:
L:
6 in
(150 mm)
Transom Height
16.5 in (418 mm)
22.5 in (571 mm)
17
05/12/21 14:03:21 31ZW6601_019
INSTALLATION
When the outboard motor is installed extremely low, water may enter into the engine under case and negatively affect the performance and durability.
When installing, check that the outboard motor is high enough from the water level to keep the engine under case from waves, splash, etc.
when the engine is stopped with the boat fully loaded.
If the outboard motor is installed too low, the boat will squat and be hard to plane, and the motor will spray water that may enter the boat. It will tend to porpoise, and high-speed stability will be reduced.
Propeller ventilation will occur if the outboard motor is installed too high on the boat transom.
Optimum installation height varies with boat type and bottom shape.
Contact the boat manufacturer for any special recommendations that are unique to a specific model of boat.
If the transom needs to be modified to accommodate the outboard motor, contact the boat manufacturer and follow their recommendations for corrective action.
ATTACHMENT
STERN BRACKET
SAFETY ROPE CLAMP SCREWS
Attach the stern bracket to the boat transom by tightening the clamp screws.
Attach a rope from the boat to the hole in the stern bracket. This will help to prevent accidental loss of the outboard motor.
18
05/12/21 14:03:25 31ZW6601_020
TRANSOM ANGLE
ADJUSTMENT
Use the transom angle adjusting bolt
22 ) to adjust the angle of the
outboard motor so the propeller is perpendicular to the surface of the water.
INSTALLATION
19
05/12/21 14:03:33 31ZW6601_021
BEFORE OPERATION
ARE YOU READY TO GET
UNDER WAY?
Your safety is your responsibility. A little time spent in preparation will significantly reduce your risk of injury.
Knowledge
Read and understand this manual.
Know what the controls do and how to operate them.
Familiarize yourself with the outboard motor and its operation before you get under way. Know what to do in case of emergencies.
Familiarize yourself with all laws and regulations relating to boating and the use of outboard motors.
Safety
Always wear a PFD (Personal
Flotation Device) while on the boat.
Attach the emergency stop switch lanyard securely to your PFD or to your wrist.
IS YOUR OUTBOARD
MOTOR READY TO GO?
For your safety, and to maximize the service life of your equipment, it is very important to take a few moments before you operate the outboard motor to check its condition.
Be sure to take care of any problem you find, or have your authorized
Honda marine dealer correct it, before you operate the outboard motor.
Improperly maintaining this outboard motor, or failing to correct a problem before operation, can cause a malfunction in which you could be seriously hurt or killed.
Always perform a preoperation inspection before each operation, and correct any problem.
20
05/12/21 14:03:43 31ZW6601_022
Safety Inspection
Look around the outboard motor for signs of oil or gasoline leaks.
Wipe up any spills before starting the engine.
Check the stern bracket to be sure the outboard motor is securely installed.
Check that all controls are operating properly.
Replace any damaged parts.
Check that all fasteners are in place and securely tightened.
Maintenance Inspection
Check the engine oil level (p.
Running the engine with a low oil level can cause engine damage.
Check to be sure the propeller is
Check that the anode is securely attached to the antiventilation plate
worn. The anode helps to protect the outboard motor from corrosion.
Make sure the tool kit and emergency starter rope are
missing items.
Check the fuel level in the fuel
BEFORE OPERATION
21
05/12/21 14:03:52 31ZW6601_023
OPERATION
SAFE OPERATING
PRECAUTIONS
To safely realize the full potential of this outboard motor, you need a complete understanding of its operation and a certain amount of practice with its controls.
Before operating the outboard motor for the first time, please review the
IMPORTANT SAFETY
INFORMATION chapter titled
and the
BEFORE OPERATION.
For your safety, avoid starting or operating the engine in an enclosed area. Your engine’s exhaust contains poisonous carbon monoxide gas which can collect rapidly in an enclosed area and cause illness or death.
BREAK-IN PROCEDURE
Proper break-in procedure allows the moving parts to wear in smoothly for best performance and long service life.
For the first 10 hours, run the outboard motor at low speed, and avoid full-throttle operation.
TRANSOM ANGLE
ADJUSTMENT
The transom angle adjusting bolt is used to adjust the angle of the outboard motor in the normal
1.
To adjust, first tilt the outboard motor so it is not resting on the bolt.
There are four adjustment positions.
2.
Loosen the wing nut to free the adjusting bolt.
3.
Adjust the angle of the motor, and tighten the wing nut. Be sure that the bolt head and wing nut are seated in one of the four adjustment positions.
To prevent damage to the motor or boat, make sure the transom angle adjusting bolt is tight.
ADJUSTING BOLT AND WING NUT
22
05/12/21 14:04:00 31ZW6601_024
STARTING THE ENGINE
EMERGENCY STOP
SWITCH CLIP
LANYARD
ENGINE STOP
SWITCH
1.
Put the emergency stop switch clip in the engine stop switch, and attach the lanyard to your PFD
(Personal Flotation Device) or to your wrist, as shown.
OPERATION
The engine will not start or run, unless the clip is in the switch.
The emergency stop switch clip and lanyard system is a safety device that will stop the engine if you fall away from the controls while operating the boat.
Always attach the lanyard to your
PFD, or to your wrist, before starting the engine.
OPEN
VENT KNOB
FUEL FILLER CAP
2.
Open the fuel tank vent by turning the vent knob at least 2 or 3 turns counterclockwise.
23
05/12/21 14:04:07 31ZW6601_025
OPERATION
FUEL VALVE LEVER
THROTTLE LEVER type: SCAB
THROTTLE LEVER
ON
START
3.
Move the fuel valve lever to the
ON position.
THROTTLE GRIP type: SHA, SCHA,
LCHA
THROTTLE GRIP
4.
Move the throttle lever or the throttle grip to the START position.
Do not start the engine with the throttle lever or the throttle grip in the FAST position, or the boat will move suddenly when the engine starts.
START
24
05/12/21 14:04:14 31ZW6601_026
CHOKE KNOB
O F F
ON
STARTER GRIP
OPERATION
7.
If the choke knob was pulled to the ON position to start the engine, gradually push it to the OFF position as the engine warms up.
Also, as the engine warms up, the throttle lever or the throttle grip can be turned to the SLOW position without stalling.
8.
Before getting under way, allow the engine to warm up sufficiently to ensure good performance.
5.
To start a cold engine, pull the choke knob to the ON position. To restart a warm engine, leave the choke knob in the OFF position.
6.
Pull the recoil starter grip slowly until you feel resistance, then pull briskly.
Return the starter grip gently.
25
05/12/21 14:04:22 31ZW6601_027
OPERATION
EMERGENCY STARTING
If the recoil starter is not working properly, you can start the engine manually using the emergency starter rope supplied with the tool kit.
ENGINE COVER
RECOIL STARTER STARTER ROPE
1.
Remove the engine cover.
5 mm NUTS
2.
Remove the three 5 mm nuts with an 8 mm wrench and remove the recoil starter.
3.
Set the controls the same as for
25
). Use the choke control if
needed.
4.
Set the knotted end of the emergency starter rope in the notch in the flywheel. Wind the rope clockwise around the flywheel, as shown.
26
05/12/21 14:04:31 31ZW6601_028
5.
Pull the emergency starter rope slowly until resistance is felt, then pull briskly.
Keep away from moving parts while pulling the rope.
If necessary, rewind the rope and pull again. If the engine does not start after several attempts, refer to
TAKING CARE OF
UNEXPECTED PROBLEMS,
6.
If the choke was used to start the engine, return the knob to the normal operating position as the engine warms up.
7.
Leave the recoil starter assembly off, but install the engine cover
Exposed moving parts can cause injury.
Do not operate the outboard motor without the engine cover.
Use extreme care when installing the engine cover.
OPERATION
8.
If it was necessary to remove the emergency stop switch lanyard from your wrist to perform the emergency starting procedure, be sure the lanyard is attached to your wrist before operating the outboard motor.
9.
Have your closest authorized
Honda marine dealer check your recoil starter system and correct the problem, so you can use the recoil starter.
The recoil starter assembly should be reinstalled after the recoil starter is working again. Install the recoil starter assembly with the engine stopped.
27
05/12/21 14:04:40 31ZW6601_029
OPERATION
STOPPING THE ENGINE
Emergency Engine Stopping
LANYARD
Normal Engine Stopping
THROTTLE LEVER type: SCAB
THROTTLE LEVER
ENGINE STOP SWITCH
P U S H
SLOW
SWITCH CLIP
To stop the engine in an emergency, pull the clip out of the engine stop switch by pulling the lanyard.
We suggest that you stop the engine this way occasionally to verify that the engine or emergency stop switch is operating properly.
THROTTLE GRIP type: SHA, SCHA,
LCHA
THROTTLE GRIP
SLOW
1.
Move the throttle lever or the throttle grip to the SLOW position.
2.
Push the engine stop switch button until the engine stops.
In the event that the engine does not stop when you push the engine stop switch, pull the emergency engine stop switch lanyard. If the engine continues to run, move the fuel valve lever to the OFF position and pull the choke knob to stop the engine.
28
05/12/21 14:04:45 31ZW6601_030
FUEL VALVE LEVER
FUEL CAP VENT KNOB
O F F
3.
Move the fuel valve lever to the
OFF position.
FUEL FILLER CAP
4.
Close the fuel tank vent by turning vent knob clockwise.
OPERATION
29
05/12/21 14:04:51 31ZW6601_031
OPERATION
THROTTLE OPERATION
THROTTLE LEVER type: SCAB
THROTTLE LEVER
Use the throttle friction knob to help hold a constant throttle setting while cruising.
Turn the knob clockwise to increase throttle grip friction for holding a constant speed.
Turn the knob counterclockwise to decrease friction for easy grip rotation.
FAST
THROTTLE GRIP type: SHA, SCHA,
LCHA
THROTTLE FRICTION KNOB
THROTTLE GRIP
FAST
30
05/12/21 14:04:57 31ZW6601_032
REVERSING THE
OUTBOARD MOTOR
INPORTANT SAFETY PRECAUTIONS
Bef ore rotating the outboard motor (f rom either f orward to reverse or f rom reverse to f orward) reduce the engine speed to SLOW, or the boat could capsize.
When operating in reverse, proceed with caution to avoid hitting any underwater obstructions with the propeller.
THROTTLE LEVER type: SCAB
THROTTLE LEVER
SLOW
THROTTLE GRIP type: SHA, SCHA,
LCHA
THROTTLE GRIP FRICTION KNOB
THROTTLE GRIP
OPERATION
1.
For the throttle lever type: Move the throttle lever to the SLOW position.
For the throttle grip type: Move the throttle grip to the SLOW position and hold it there by turning the throttle grip friction knob clockwise.
SLOW
31
05/12/21 14:05:04 31ZW6601_033
OPERATION
STEERING
STEERING FRICTION BOLT
T O I N C R E A S E
F R I C T I O N
TO DECREASE
FRICTION
2.
To reverse direction, turn the outboard motor 180°, and then pivot the tiller handle as shown.
For the throttle grip type, be careful not to hold and move the throttle grip when pivoting the tiller handle.
Steer by moving the tiller handle opposite the direction you want the boat to turn.
Use the steering friction bolt to help hold a steady course while cruising.
Turn the bolt clockwise to increase steering friction for holding a steady course.
Turn the bolt counterclockwise to decrease friction for easy turning.
32
05/12/21 14:05:14 31ZW6601_034
OPERATION
CRUISING
Engine Speed
For best fuel economy, limit the throttle opening to 80%. Use the
help you hold a steady speed.
For rough water conditions or large waves, slow down to prevent the propeller from rising out of the water.
Transom Angle
Install the outboard motor at the best transom angle for stable cruising and maximum power.
Transom angle too large: Incorrect causes boat to ‘‘squat’’.
Transom angle too small: Incorrect causes boat to ‘‘bow steer’’.
It is necessary to adjust the transom angle to compensate for changes in boat load, weight distribution, water conditions, or propeller selection.
Under normal running conditions, the boat will perform best when the antiventilation plate is level with the water surface.
When cruising into a high wind, lower the transom angle slightly to level the boat and improve stability.
With a tail wind, raise the transom angle slightly.
Excessive transom angle during operation can cause propeller ventilation and overheating.
Transom Angle (Cruising)
O.K.
CORRECT
GIVES MAXIMUM PERFORMANCE
33
05/12/21 14:05:20 31ZW6601_035
OPERATION
MOORING, BEACHING,
LAUNCHING
To raise the outboard motor out of the water while the boat is moored, or for maximum clearance when beaching or launching, tilt the outboard motor to the 75° position.
Stop the engine before tilting the outboard motor. The 75° position is not an operating position.
REAR CARRYING
HANDLE
STEERING
FRICTION BOLT
1.
Stop the engine and turn the fuel valve lever off.
2.
Close the fuel tank vent by turning the vent knob clockwise.
3.
With the motor in the forward position, tilt the outboard motor using the front and rear carrying handles on the engine cover. The spring-loaded tilt lever will automatically move into position and hold the outboard motor when it reaches approximately 75°.
4.
Adjust the steering friction bolt to keep the motor from moving.
Do not use the tiller handle as a lever to raise the outboard motor.
Applying excessive f orce to the tiller handle can damage it.
If the motor is tilted in the reverse position, crankcase oil will enter the cylinder and may cause dif f icult starting or may prevent the engine f rom being cranked.
FRONT
CARRYING
HANDLE
34
75°
05/12/21 14:05:26 31ZW6601_036
TILT LEVER
P U L L
NO
5.
To return the outboard motor to the normal running position, hold the outboard motor by the front carrying handle on the engine case and pull the tilt level toward you, then lower the outboard motor slowly.
To avoid damaging the motor, be very caref ul when mooring a boat, especially when its motor is tilted up.
Don’t allow the motor to strike against the pier or other boats.
OPERATION
35
05/12/21 14:05:32 31ZW6601_037
SERVICING YOUR OUTBOARD MOTOR
THE IMPORTANCE OF
MAINTENANCE
Proper maintenance is essential for safe, economical, and trouble-free operation. It will also help reduce air pollution.
Improperly maintaining this outboard motor, or failure to correct a problem before operation, can cause a malfunction in which you could be seriously hurt or killed.
Always follow the inspection and maintenance recommendations and schedules in this owner’s manual.
To help you properly care for your outboard motor, the following pages include a maintenance schedule, routine inspection procedures, and simple maintenance procedures using basic hand tools. Other service tasks that are more difficult, or require special tools, are best handled by professionals and are normally performed by a Honda technician or other qualified mechanic.
The maintenance schedule applies to normal operating conditions. If you operate your outboard motor under unusual conditions, consult an authorized Honda marine dealer for recommendations applicable to your individual needs and use.
Remember that your authorized
Honda marine dealer knows your outboard motor best and is fully equipped to maintain and repair it.
To ensure the best quality and reliability, use only new, genuine
Honda parts or their equivalents for repair and replacement.
Maintenance, replacement, or repair of the emission control devices and systems may be performed by any marine engine repair establishment or individual, using parts that are ‘‘certified’’ to
EPA standards.
36
05/12/21 14:05:41 31ZW6601_038
MAINTENANCE SAFETY
Some of the most important safety precautions follow. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.
Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.
Always follow the procedures and precautions in the owner’s manual.
SERVICING YOUR OUTBOARD MOTOR
Safety Precautions
Make sure the engine is off before you begin any maintenance or repairs. This will eliminate several potential hazards:
− Carbon monoxide poisoning from engine exhaust.
Be sure there is adequate ventilation whenever you operate the engine.
− Burns from hot parts.
Let the engine and exhaust system cool before touching.
− Injury from moving parts.
Do not run the engine unless instructed to do so.
Read the instructions before you begin, and make sure you have the tools and skills required.
To reduce the possibility of fire or explosion, be careful when working around gasoline. Use only a nonflammable solvent, not gasoline, to clean parts. Keep cigarettes, sparks, and flames away from all fuel-related parts.
Wear gloves when handling the propeller to protect your hands from sharp edges.
37
05/12/21 14:05:48 31ZW6601_039
SERVICING YOUR OUTBOARD MOTOR
TOOL KIT AND
EMERGENCY STARTER
ROPE
8 × 10 mm WRENCH FLAT/PHILLIPS
SCREWDRIVER
EMERGENCY STOP
SWITCH CLIP
EMERGENCY STARTER ROPE
The following tools are supplied with the outboard motor for simple maintenance procedures and emergency repairs. An emergency starter rope is also supplied. Keep these items on the boat, so they will always be available if you need them.
If your tool kit needs replacement, it is not available as a kit and each item must be ordered individually.
SPARK PLUG WRENCH
COTTER PINS
38
PLIERS
SHEAR PINS
TOOL BAG
05/12/21 14:05:58 31ZW6601_040
SERVICING YOUR OUTBOARD MOTOR
MAINTENANCE SCHEDULE
Follow the MAINTENANCE SCHEDULE table and service your outboard motor accordingly. Please note, a claim for warranty coverage will not be denied simply because the maintenance schedule for your outboard was not followed.
However, any part(s) that fails specifically due to lack of maintenance, or improperly performed maintenance, would not be covered under the Distributor’s Limited Warranty .
REGULAR SERVICE PERIOD (3)
Perform at every indicated month or operating hour interval, whichever comes first.
ITEM
Engine oil Check level
Change
Gear case oil
Starter rope
Carburetor linkage
Valve clearance
Spark plug
Propeller and Cotter pin
Anode
Idle speed
Clutch shoes and drum
(With clutch type)
Change
Check
Check-adjust
Check-adjust
Check-adjust
Replace
Check
Check
Check-adjust
Replace
Each use
○
○
○
First month or
10 hrs.
○
○
○ (2)
Every 200 hrs.
○
○
○
○ (2)
○
○ (2)
Every 6 months or
50 hrs.
○ (2)
Every year or
150 hrs.
○ (2)
○ (2)
(1) Lubricate more frequently when used in salt water.
(2) These items should be serviced by an authorized Honda marine dealer, unless you have the proper tools and are mechanically proficient.
Refer to the Honda shop manual for service procedures.
(3) For professional/commercial use, log hours of operation to determine proper maintenance intervals.
39
05/12/21 14:06:08 31ZW6601_041
SERVICING YOUR OUTBOARD MOTOR
REGULAR SERVICE PERIOD (3)
Perform at every indicated month or operating hour interval, whichever comes first.
ITEM
Swivel case lining and bushing
Water sealing
Fuel line
Replace
Bolts and nuts
Lubrication
Fuel tank and tank filter
Crankcase breather tube
Replace
Check
Replace
Check-tightness
Grease
Clean
Check
(1) Lubricate more frequently when used in salt water.
Each use
○
First month or
10 hrs.
Every 6 months or
50 hrs.
Every 3 years (2)
Every 3 years (2)
Every 2 years (If necessary) (2)
○
○
(2)
(1) ○
○
(1)
(2)
Every year or
150 hrs.
○ (2)
○ (2)
(2) These items should be serviced by an authorized Honda marine dealer, unless you have the proper tools and are mechanically proficient.
Refer to the Honda shop manual for service procedures.
(3) For professional/commercial use, log hours of operation to determine proper maintenance intervals.
40
05/12/21 14:06:21 31ZW6601_042
SERVICING YOUR OUTBOARD MOTOR
ENGINE COVER REMOVAL
AND INSTALLATION
ENGINE COVER
STRAP
The engine cover retaining strap fastens the engine cover to the outboard motor.
To remove the engine cover, unhook the engine cover retaining strap, then lift the engine cover off the outboard motor.
To install the engine cover, place the cover on the outboard motor, then hook the engine cover retaining strap securely.
Engine Oil Level Check
Check the engine oil level with the engine stopped and the outboard motor in the vertical position.
U P P E R L I M I T
L O W E R L I M I T
OIL LEVEL
INSPECTION
WINDOW
1.
Check the oil level shown on the oil level inspection window.
2.
If the oil level is near or below the lower limit mark on the window, fill with the recommended oil to the upper limit mark on the window.
Running the engine with a low oil level can cause engine damage.
Engine Oil Change
An engine oil evacuation device may be used to remove the engine oil.
Drain the used oil while the engine is warm. Warm oil drains quickly and completely.
1.
Move the fuel valve lever to the
OFF position, and turn the fuel cap vent knob clockwise to close the fuel vent.
2.
Loosen the oil drain bolt, and turn the motor on its tiller handle side.
3.
Remove the oil drain bolt and washer to drain the oil.
U P P E R L I M I T M A R K
L O W E R L I M I T M A R K
OIL DRAIN BOLT
OIL LEVEL
INSPECTION
WINDOW
41
05/12/21 14:06:32 31ZW6601_043
SERVICING YOUR OUTBOARD MOTOR
OIL FILLER CAP
OIL FILLER HOLE
4.
Stand the outboard motor in a vertical position, and install a new washer and the oil drain bolt securely.
5.
Remove the engine cover.
Improper disposal of engine oil can be harmf ul to the environment.
If you change your own oil, please dispose of the used oil properly.
Put it in a sealed container, and take it to a recycling center. Do not discard it in a trash bin, dump it on the ground or pour it down a drain.
6.
Remove the oil filler cap and fill the crankcase with the recommended oil up to the upper limit mark on the oil level inspection window.
Engine oil refill capacity:
0.26 US qt (0.25 )
7.
8.
Install the oil filler cap and tighten it securely.
Install the engine cover.
Engine Oil Recommendations
Oil is a major factor affecting performance and service life. Use
4-stroke automotive detergent oil.
SAE Viscosity Grade
AMBIENT TEMPERATURE
SAE 10W-30 is recommended for general use.
The SAE oil viscosity and service classification are in the API label on the oil container. Honda recommends that you use API SERVICE category
SG or later oil with the ‘‘starburst’’ certification mark displayed on the container.
42
05/12/21 14:06:42 31ZW6601_044
Gear Oil Change
Change the gear oil with the engine stopped and the outboard motor in the vertical position.
GEAR OIL
LEVEL PLUG
GEAR OIL LEVEL
DRAIN PLUG
1.
Place a suitable container below the oil drain hole to catch the used oil. Remove the oil drain plug and then remove the oil level plug.
GEAR OIL BOTTLE
SERVICING YOUR OUTBOARD MOTOR
2.
Allow the used oil to drain completely, then install an oil pump adapter in the oil drain hole.
If water or contaminated (milkycolored) oil flows out the drain hole when the plug is removed, have the outboard motor checked by an authorized Honda marine dealer.
3.
Add oil through the oil drain hole until it flows out the oil level hole, then install the oil level plug.
Remove the pump adapter and install the oil drain plug.
GEAR OIL CAPACITY:
0.05 US qt (0.05 )
Outboard motor SAE 90 hypoid gear oil API Service classification
(GL-4 or GL-5)
OIL LEVEL PLUG TORQUE:
2.5 lbf·ft (3.4 N·m , 0.35 kgf·m)
Avoid losing more than 1 fl oz (30 plug.
OIL DRAIN PLUG TORQUE:
2.5 lbf·ft (3.4 N·m , 0.35 kgf·m)
43
05/12/21 14:06:50 31ZW6601_045
SERVICING YOUR OUTBOARD MOTOR
Lubrication Points
Apply marine waterproof grease to the following parts:
Lubrication interval:
10 operating hours or one month after the date of purchase or initial use, then every 50 operating hours or 6 months.
THROTTLE ARM
To prevent corrosion, apply anticorrosion oil to pivot surf aces where grease cannot penetrate.
TILT LEVER
THROTTLE ARM
CHOKE ARM
STEERING HANDLE
CLAMP SCREW
SWIVEL CASE
STEERING FRICTION BOLT
TRANSOM ANGLE
ADJUSTING BOLT
THRUST RECEIVER
Apply Honda Marine Corrosion Inhibitor (or equivalent) to all areas under the engine cover and any exposed metal surfaces.
44
05/12/21 14:06:58 31ZW6601_046
SERVICING YOUR OUTBOARD MOTOR
Spark Plug Service
RECOMMENDED SPARK PLUG:
CR4HSB (NGK)
U14FSR-UB (DENSO)
SPARK PLUG WRENCH
0.024
− 0.028 in
(0.60
− 0.70 mm)
Incorrect spark plug can cause engine damage.
1.
2.
Disconnect the spark plug cap from the spark plug.
3.
Remove the spark plug with a spark plug wrench and screwdriver supplied in the tool kit.
4.
Inspect the spark plug. Replace it if the electrode is worn, or if the insulator is cracked or chipped.
SEALING WASHER
5.
Measure the spark plug electrode gap with a wire-type feeler gauge.
The gap should be 0.024
− 0.028
inches (0.60
− 0.70 mm). Correct the gap, if necessary, by bending the side electrode.
45
05/12/21 14:07:05 31ZW6601_047
SERVICING YOUR OUTBOARD MOTOR
6.
Install the spark plug carefully, by hand, to avoid cross-threading.
7.
After the spark plug seats, tighten with a spark plug wrench supplied in the tool kit to compress the sealing washer.
If reinstalling the used spark plug, tighten 1/8 - 1/4 turn after the spark plug seats.
If installing a new spark plug, tighten 1/2 turn after the spark plugs seat.
A loose spark plug can overheat and damage the engine.
Overtightening the spark plug can damage the threads in the cylinder head.
8.
Attach the spark plug cap.
9.
Install the engine cover.
46
05/12/21 14:07:15 31ZW6601_048
REFUELING
FUEL TANK CAPACITY:
0.26 US gal (1.0 )
With the engine stopped, turn the vent knob counterclockwise to open the fuel tank vent, then remove the fuel filler cap.
Refill the fuel tank if the fuel level is low.
SERVICING YOUR OUTBOARD MOTOR
FUEL FILLER CAP
VENT KNOB
MAXIMUM FUEL LEVEL
FUEL TANK
FUEL
Gasoline is highly flammable and explosive.
You can be burned or seriously injured when handling fuel.
Stop the engine and keep heat, sparks, and flame away.
Handle fuel only outdoors.
Wipe up spills immediately.
Refuel in a well-ventilated area. Fill the tank to the maximum fuel level.
After refueling, install the cap and tighten it securely. Turn the vent knob clockwise to close the fuel tank vent.
Never refill the fuel tank inside a building where gasoline fumes may reach flames or sparks. Keep gasoline away from appliance pilot lights, barbecues, electric appliances, power tools, etc.
Spilled fuel is not only a fire hazard, it causes environmental damage.
Wipe up spills immediately.
47
05/12/21 14:07:22 31ZW6601_049
SERVICING YOUR OUTBOARD MOTOR
FUEL RECOMMENDATIONS
Use unleaded gasoline with a pump octane rating of 86 or higher.
This outboard motor is certified to operate on unleaded gasoline.
Unleaded gasoline produces fewer engine and spark plug deposits and extends exhaust system life.
Never use stale or contaminated gasoline or an oil/gasoline mixture.
Avoid getting dirt or water in the fuel tank.
Occasionally you may hear a light
‘‘spark knock’’ or ‘‘pinging’’
(metallic rapping noise) while operating under heavy loads. This is no cause for concern.
If spark knock or pinging occurs at a steady engine speed, under normal load, change brands of gasoline. If spark knock or pinging persists, see an authorized Honda marine dealer.
Running the engine with persistent spark knock or pinging can cause engine damage.
Running the engine with persistent spark knock or pinging is misuse, and the Distributor’s Limited
Warranty
parts damaged by misuse.
For information regarding oxygenated fuels, please refer to
48
05/12/21 14:07:30 31ZW6601_050
Recoil Starter Rope Inspection
RECOIL STARTER ROPE
SERVICING YOUR OUTBOARD MOTOR
Anode Replacement
Short shaft type Long shaft type Painting or coating the anode will def eat its purpose and will lead to rust and corrosion damage to the outboard motor. The anode must be exposed to the water in order to protect the outboard motor.
Inspect the recoil starter rope, and replace it if it becomes frayed.
Always keep the emergency starter rope on the boat in case the recoil starter rope fails.
ANODE
The anode is made of a sacrificial material that helps to protect the outboard motor from corrosion.
Replace the anode when it has been reduced to about half its original size, or if it is crumbling.
49
05/12/21 14:07:39 31ZW6601_051
SERVICING YOUR OUTBOARD MOTOR
Propeller Replacement
Before replacing the propeller, remove the clip from the engine stop switch to prevent any possibility of the engine being started while you are working with the propeller.
The propeller blades may have sharp edges, so wear heavy gloves to protect your hands.
Operating the outboard motor at higher altitudes will reduce available power. This may require decreasing the propeller pitch to maintain correct engine RPM.
Removal
COTTER PIN
SHEAR PIN PROPELLER
Remove the cotter pin, then remove the propeller and shear pin.
Installation
COTTER PIN
Install the propeller in the reverse order of removal.
Use a genuine Honda stainless steel cotter pin and bend the pin ends as shown. A non-stainless steel cotter pin can deteriorate if used in saltwater.
Spare shear pins and cotter pins are provided on the engine undercase
50
05/12/21 14:07:48 31ZW6601_052
STORAGE
STORAGE PREPARATION
Proper storage preparation is essential for keeping your outboard motor trouble-free and looking good.
The following steps will help to keep rust and corrosion from impairing your outboard motor’s function and appearance, and will make the engine easier to start when you use the outboard motor again.
Cleaning
Thoroughly clean and flush the outboard motor with fresh water after operation in dirty water or salt water.
Wash the outside of the outboard motor with clean, fresh water to remove mud, salt, seaweed, etc.
Touch up any damaged paint, and coat areas that may rust with Honda
Corrosion Inhibitor, or equivalent.
Lubricate controls with a silicone spray lubricant.
Fuel
Depending on the region where you operate your outboard, f uel f ormulations may deteriorate and oxidize rapidly. Fuel deterioration and oxidation can occur in as little as 15 days and may cause damage to the carburetors and f uel system.
Please check with your servicing dealer f or local storage recommendations.
Gasoline will oxidize and deteriorate in storage. Old gasoline will cause hard starting, and it leaves gum deposits that clog the fuel system. If the gasoline in your fuel tank and carburetor deteriorates during storage, you may need to have the carburetor and other fuel system components serviced or replaced.
The length of time that gasoline can be left in your fuel tank and carburetor without causing functional problems will vary with such factors as gasoline blend, your storage temperatures, and whether the fuel tank is partially or completely filled.
The air in a partially filled fuel tank promotes fuel deterioration. Very warm storage temperatures accelerate fuel deterioration. Fuel deterioration problems may occur in less than 30 days, if the gasoline was not fresh when you filled the fuel tank.
The Distributor’s Limited Warranty does not cover fuel system damage or engine performance problems resulting from neglected storage preparation.
You can extend fuel storage life by adding a gasoline stabilizer that is formulated for that purpose, or you can avoid fuel deterioration problems by draining all the fuel from the fuel tank and carburetor.
51
05/12/21 14:07:59 31ZW6601_053
STORAGE
Adding a Fuel Stabilizer
When adding a fuel stabilizer, fill the fuel tank with fresh gasoline. If only partially filled, air in the tank will promote fuel deterioration during storage. If you keep a container of gasoline for refueling, be sure that it contains only fresh gasoline.
1.
Add fuel stabilizer following the manufacturer’s instructions.
2.
After adding a fuel stabilizer, run the engine outdoors for 10 minutes to be sure that the treated gasoline has replaced the untreated gasoline in the carburetor.
Starting the engine on land:
For safety, remove the propeller from
ANTIVENTILATION PLATE
Place a container under the outboard motor, and fill it with clean, fresh water. The water level must be at least 6 inches above the antiventilation plate.
Running the engine without water can cause overheating and damage.
Damage caused by running the outboard motor without water is not covered by the Distributor’s Limited
Warranty.
3.
Turn the engine OFF, turn the fuel
valve lever OFF (p.13), and close
the fuel cap vent knob (p.29).
52
Draining the Fuel Tank and
Carburetor
You can avoid fuel deterioration problems by draining the fuel tank and carburetors.
1.
With the outboard motor in a vertical position, place an approved gasoline container below the fuel drain outlet, and use a funnel to avoid spilling fuel.
Gasoline is highly flammable and explosive.
You can be burned or seriously injured when handling fuel.
Stop the engine and keep heat, sparks, and flame away.
Handle fuel only outdoors.
Wipe up spills immediately.
05/12/21 14:08:12 31ZW6601_054
2.
With the engine stopped, turn the fuel cap vent knob counterclockwise to open the fuel vent, then and remove the fuel filler cap.
3.
Loosen the carburetor drain screw and move the fuel valve lever to the ON position to drain the carburetor and the fuel tank into an approved gasoline container.
DRAIN SCREW
Engine Oil
1.
2.
3.
4.
5.
42 ).
and remove the clip from the engine stop switch.
Pour a tablespoon (5 − 10 cm ) of clean engine oil into the cylinder.
Pull the starter rope several times to distribute the oil in the cylinder.
STORAGE PRECAUTIONS
Select a well-ventilated storage area.
If possible, avoid storage areas with high humidity.
4.
After draining is completed, tighten the carburetor drain screw and turn the fuel valve to the OFF position.
5.
Install the fuel filler cap and turn the fuel filler cap vent knob clockwise to close the fuel vent.
STORAGE
To carry the outboard motor, hold it by the carrying handle, as shown.
Lif ting the outboard motor by the engine cover, or using the installed outboard motor as a handle or lever to move the boat, can damage the outboard motor.
If your fuel tank contains gasoline, store it away from any appliance that operates with a flame, such as a furnace, water heater, or clothes dryer. Also avoid any area with a spark-producing electric motor, or where power tools are operated.
Store the outboard motor either vertically or horizontally with the tiller handle side up.
53
05/12/21 14:08:20 31ZW6601_055
STORAGE
CORRECT
CASE PROTECTOR
If storing horizontally, be sure to fold the tiller handle, and rest the outboard motor on its case protectors.
Any other horizontal storage position may cause damage or oil leakage.
INCORRECT
Cover the outboard motor to keep out dust. Do not use sheet plastic as a dust cover. A nonporous cover will trap moisture, promoting rust and corrosion.
REMOVAL FROM STORAGE
Check your outboard motor as described in the BEFORE
OPERATION chapter of this manual.
If the cylinder was coated with oil during storage preparation, the engine may smoke briefly at startup.
This is normal.
54
05/12/21 14:08:28 31ZW6601_056
TRANSPORTING
WITH OUTBOARD MOTOR
INSTALLED ON BOAT
When trailering a boat with the outboard motor attached, leave the engine in the normal running position, if possible, and tighten the steering
If there is insufficient road clearance in the normal running position, then tilt the outboard motor and use a motor support bar, or remove the outboard motor from the boat. Refer to the manufacturer’s instructions for using a motor support bar.
WITH OUTBOARD MOTOR
REMOVED FROM BOAT
Remove the outboard motor from the boat and secure the outboard motor in either the vertical or horizontal
Lif ting the outboard motor by the engine cover, or using the installed outboard motor as a handle or lever to move the boat, can damage the outboard motor.
To carry, hold the outboard motor by the carrying handle, as shown.
MOTOR SUPPORT BAR
(commercially available)
55
05/12/21 14:08:36 31ZW6601_057
TAKING CARE OF UNEXPECTED PROBLEMS
ENGINE WILL NOT START
1.
Check emergency stop switch clip.
2.
Check control positions.
Possible Cause
Clip not inserted in stop switch.
Choke knob in OFF position.
Throttle lever or grip not in
START position.
Correction
Insert clip in stop switch.
Pull choke knob to ON position,
Turn throttle lever or grip to
56
05/12/21 14:08:48 31ZW6601_058
TAKING CARE OF UNEXPECTED PROBLEMS
ENGINE WILL NOT START
(continued)
3.
Check fuel.
Possible Cause
4.
Remove and inspect spark plug.
5.
Take outboard motor to an authorized Honda marine dealer, or refer to the shop manual.
Out of fuel.
Fuel vent closed.
Fuel valve lever in the OFF position.
Bad fuel; boat stored without treating or draining gasoline, or refueled with bad gasoline.
Spark plug faulty, fouled or improperly gapped.
Spark plug wet with fuel (flooded engine).
Carburetor malfunction, ignition malfunction, stuck valves, etc.
Correction
Move the fuel valve lever to the
Drain fuel tank and carburetor
Dry and reinstall spark plug. Start engine with choke and throttle open.
Replace or repair faulty components as necessary.
57
05/12/21 14:09:01 31ZW6601_059
TAKING CARE OF UNEXPECTED PROBLEMS
HARD STARTING OR STALLS
AFTER STARTING
1.
Check control positions.
Possible Cause
Choke knob in OFF position.
2.
3.
Check fuel.
Remove and inspect spark plug.
4.
Take outboard motor to an authorized Honda marine dealer, or refer to the shop manual.
Throttle lever or grip not in
START position.
Fuel vent closed.
Bad fuel; boat stored without treating or draining gasoline, or refueled with bad fuel.
Spark plug faulty, fouled or improperly gapped.
Carburetor malfunction, ignition malfunction, etc.
Correction
Pull choke knob to ON position,
Turn throttle lever or grip to
Drain fuel tank and carburetor
Replace or repair faulty components as necessary.
58
05/12/21 14:09:07 31ZW6601_060
TAKING CARE OF UNEXPECTED PROBLEMS
ENGINE WILL NOT DRIVE
THE PROPELLER
1.
Check shear pin.
2.
Take outboard motor to an authorized Honda marine dealer, or refer to the shop manual.
Possible Cause
Broken shear pin.
Damaged clutch, drive train, or engagement mechanism.
Correction
Replace or repair faulty components as necessary.
59
05/12/21 14:09:15 31ZW6601_061
TAKING CARE OF UNEXPECTED PROBLEMS
SUBMERGED MOTOR
A submerged outboard motor must be serviced immediately after it is recovered from the water in order to minimize corrosion.
If there is a Honda marine dealer nearby, take the motor to the dealer immediately. If you are far from a dealer, proceed as follows:
1.
Remove the engine cover, and rinse the outboard motor with fresh water to remove salt water, sand, mud, etc.
2.
Drain the carburetor as described
3.
Change the engine oil as described
in the engine crankcase, or if the used engine oil showed signs of water contamination, then a second engine oil change should be performed after running the engine for half an hour.
STARTER GRIP
4.
and remove the clip from the engine switch. Pull the recoil starter grip, rotate the flywheel a few revolutions to completely expel any water from the cylinder.
If the engine was running when it submerged, there may be mechanical damage, such as a bent connecting rod. If the engine binds when cranked, do not attempt to run the engine until it has been repaired.
60
05/12/21 14:09:21 31ZW6601_062
When cranking the engine with an open ignition circuit (spark plug removed f rom the ignition circuit), remove the clip f rom the engine stop switch to prevent possible damage to the ignition system.
TAKING CARE OF UNEXPECTED PROBLEMS
5.
Pour a teaspoon of engine oil into the spark plug hole, then pull the recoil starter grip several times to lubricate the inside of the cylinder.
6.
Reinstall the spark plug, and put the emergency stop switch clip into the switch.
7.
Attempt to start the engine.
If the engine fails to start, remove the spark plug, and dry it, then reinstall the spark plug and attempt to start the engine again.
If the engine starts, and no mechanical damage is evident, continue to run the engine for a half hour or longer.
8.
As soon as possible, take the outboard motor to an authorized
Honda marine dealer for inspection and service.
61
05/12/21 14:09:29 31ZW6601_063
TECHNICAL AND CONSUMER INFORMATION
TECHNICAL INFORMATION
Serial Number Locations
Record the product identification number, the engine serial number and the date of purchase in the space provided on this page. You will need these numbers when ordering parts, and when making technical or
PRODUCT
IDENTIFICATION
NUMBER
The product identification number is stamped on a plate attached on side of the stern bracket.
Product identification number:
ENGINE SERIAL
NUMBER
The engine serial number is stamped on the engine.
Engine serial number:
Date of purchase:
62
05/12/21 14:09:34 31ZW6601_064
TECHNICAL AND CONSUMER INFORMATION
Carburetor Modification for
High Altitude Operation
At high altitude, the standard carburetor air-fuel mixture will be too rich. Performance will decrease, and fuel consumption will increase.
A very rich mixture will also foul the spark plug and cause hard starting.
High altitude performance can be improved by specific modifications to the carburetor. If you always operate your outboard motor at altitudes above 5,000 feet (1,500 meters), have an authorized Honda marine dealer perform this carburetor modification.
Even with carburetor modification, engine horsepower will decrease about 3.5% for each 1,000-foot (300meter) increase in altitude. The effect of altitude on horsepower will be greater than this if no carburetor modification is made.
When the carburetor has been modif ied f or high altitude operation, the air-f uel mixture will be too lean f or low altitude use. Operation at altitudes below 5,000 f eet (1,500 meters) with modif ied carburetor may cause the engine to overheat and result in serious engine damage.
For use at low altitudes, have an authorized Honda marine dealer return the carburetor to original f actory specif ications.
63
05/12/21 14:09:43 31ZW6601_065
TECHNICAL AND CONSUMER INFORMATION
Oxygenated Fuels
Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and
Canada use oxygenated fuels to help reduce emissions.
If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement.
Before using an oxygenated fuel, try to confirm the fuel’s contents. Some states/provinces require this information to be posted on the pump.
The following are the EPA-approved percentages of oxygenates:
ETHANOL: ethyl or grain alcohol;
10% by volume.
You may use gasoline containing up to 10% ethanol by volume. Gasoline containing ethanol may be marketed under the name ‘‘Gasohol’’.
MTBE: Methyl Tertiary Butyl Ether;
15% by volume.
You may use gasoline containing up to 15% MTBE by volume.
METHANOL: methyl or wood alcohol; 5% by volume.
You may use gasoline containing up to 5% methanol by volume, as long as it also contains cosolvents and corrosion inhibitors to protect the fuel system. Gasoline containing more than 5% methanol by volume may cause starting and/or performance problems. It may also
64
damage metal, rubber, and plastic parts of your fuel system.
If you notice any undesirable operating symptoms, try another service station, or switch to another brand of gasoline.
Fuel system damage or performance problems resulting from the use of an oxygenated fuel containing more than the percentages of oxygenates mentioned above are not covered under warranty.
05/12/21 14:09:51 31ZW6601_066
TECHNICAL AND CONSUMER INFORMATION
Emission Control System
Information
Source of Emissions
The combustion process produces carbon monoxide, oxides of nitrogen, and hydrocarbons. Control of hydrocarbons and oxides of nitrogen is very important because, under certain conditions, they react to form photochemical smog when subjected to sunlight. Carbon monoxide does not react in the same way, but it is toxic.
Honda utilizes lean carburetor settings and other systems to reduce the emissions of carbon monoxide, oxides of nitrogen, and hydrocarbons.
The U.S. and Calif ornia Clean
Air Acts
EPA and California regulations require all manufacturers to furnish written instructions describing the operation and maintenance of emission control systems.
The following instructions and procedures must be followed in order to keep the emissions from your
Honda engine within the emission standards.
Tampering and Altering
Tampering with or altering the emission control system may increase emissions beyond the legal limit.
Among those acts that constitute tampering are:
Removal or alteration of any part of the intake, fuel, or exhaust systems.
Alterations that would cause the engine to operate outside its design parameters.
65
05/12/21 14:10:00 31ZW6601_067
TECHNICAL AND CONSUMER INFORMATION
Problems That May Af f ect
Emissions
If you are aware of any of the following symptoms, have your engine inspected and repaired by your servicing dealer.
Hard starting or stalling after starting.
Rough idle.
Misfiring or backfiring under load.
Afterburning (backfiring).
Black exhaust smoke or high fuel consumption.
Replacement Parts
The emission control systems on your Honda engine were designed, built, and certified to conform with
EPA and California emission regulations. We recommend the use of genuine Honda parts whenever you have maintenance done. These original-design replacement parts are manufactured to the same standards as the original parts, so you can be confident of their performance. The use of replacement parts that are not of the original design and quality may impair the effectiveness of your emission control system.
A manufacturer of an aftermarket part assumes the responsibility that the part will not adversely affect emission performance. The manufacturer or rebuilder of the part must certify that use of the part will not result in a failure of the engine to comply with emission regulations.
Maintenance
Follow the maintenance schedule on
39 . Remember that this schedule
is based on the assumption that your machine will be used for its designed purpose. Sustained high-load operation, or use in unusual conditions, will require more frequent service.
66
05/12/21 14:10:10 31ZW6601_068
Star Label
A Star label was applied to this outboard motor in accordance with the requirements of the California
Air Resources Board.
TECHNICAL AND CONSUMER INFORMATION
The Star Label means Cleaner Marine Engine
This engine has been certified as a:
The Symbol for Cleaner Marine Engines:
Cleaner Air and Water for healthier lifestyle and environment.
Better Fuel Economy burns up to 30 - 40 percent less gas and oil than conventional carbureted two-stroke engines, saving money and resources.
Longer Emission Warranty protects consumer for worry-free operation.
67
05/12/21 14:10:20 31ZW6601_069
TECHNICAL AND CONSUMER INFORMATION
One Star
Low
Emission
Two Stars
Very Low
Emission
The one-star label identifies engines that meet the Air Resources Board’s
Personal Watercraft and Outboard marine engine 2001 exhaust emission standards. Engines meeting these standards have 75% lower emissions than conventional carbureted two-stroke engines. These engines are equivalent to the U.S. EPA’s 2006 standards for marine engines.
The two-star label identifies engines that meet the Air Resources Board’s
Personal Watercraft and Outboard marine engine 2004 exhaust emission standards. Engines meeting these standards have 20% lower emissions than
One Star-Low Emission engines.
Three Stars
Ultra Low
Emission
Four Stars
Super Ultra
Low Emission
The three-star label identifies engines that meet the Air Resources Board’s
Personal Watercraft and Outboard marine engine 2008 exhaust emission standards or the Sterndrive and inboard marine engine 2003-2008 exhaust emission standards. Engines meeting these standards have 65% lower emissions than One Star-Low Emission engines.
The four-star label identifies engines that meet the Air Resources Board’s
Sterndrive and Inboard marine engine 2009 exhaust emission standards.
Personal Watercraft and Outboard marine engines may also comply with these standards. Engines meeting these standards have 90% lower emissions than One Star-Low Emission engines.
Cleaner Watercraft - Get the Facts
1-800-END-SMOG www.arb.ca.gov
68
05/12/21 14:10:56 31ZW6601_070
TECHNICAL AND CONSUMER INFORMATION
Specifications
MODEL
Description Code
Type
Overall length
Overall width
Overall height
Transom height
Weight
Rated power
Full throttle range
Engine type
Displacement
Spark plug gap
Starter system
Ignition system
Lubrication system
Specified oil
Oil capacity
BZBK
SHA
BF2D
SCHA
BZBF
LCHA
16.1 in (410 mm)
11.0 in (280 mm)
37.2 in
(945 mm)
16.5 in
(418 mm)
43.3 in
(1,100 mm)
22.5 in
(571 mm)
28.7 lbs
(13.0 kg)
29.8 lbs
(13.5 kg)
1.5 kW (2.0 HP)
5,000 − 6,000 rpm
4 stroke OHV 1 cylinder
30.9 lbs
(14.0 kg)
3.5 cu-in (57 cm )
0.024
− 0.028 in (0.60
− 0.70 mm)
Recoil starter
Transistorized Ignition Control Module (ICM)
Oil slinger system
Engine: API standard (SG or later oil)
SAE 10W-30
Gear case: API standard (GL4/5)
SAE 90 outboard motor gear oil
Engine:
0.26 US qt (0.25 )
Gear case:
0.05 US qt (0.05 )
CARB star label
Cooling system
Exhaust system
Spark plug
Fuel
Tank capacity
Steering equipment
Steering angle
Transom angle
Tilt angle
Clutch system
Tuneup
Spark plug gap
Idle speed
Valve clearance
(cold)
Other specifications
ULTRA LOW EMISSION
Engine: Forced air cooling
Underwater exhaust
CR4HSB (NGK)
U14FSR-UB (DENSO)
Automotive unleaded gasoline
(86 pump octane or higher)
0.26 US gal (1.0 )
Tiller handle
360°
4 stages (5°, 10°, 15°, 20°)
75°
Centrifugal clutch
0.024
− 0.028 in
(0.60
− 0.70 mm)
2,000 ± 100 rpm
See shop manual
Intake: 0.08
± 0.02 mm See shop
Exhaust: 0.11
± 0.02 mm manual
No other adjustment is needed
Honda outboards are power rated in accordance with NMMA procedures and using the ICOMIA standard 28/23.
69
05/12/21 14:11:07 31ZW6601_071
TECHNICAL AND CONSUMER INFORMATION
CONSUMER INFORMATION
Honda Publications
These publications will give you additional information for maintaining and repairing your outboard motor. You may purchase them from your Honda marine dealer.
Shop Manual
This manual covers complete maintenance and overhaul procedures.
It is intended to be used by a skilled technician.
Parts Catalog
This manual provides complete, illustrated parts lists.
Customer Service Information
Contacting Honda
Your owner’s manual was written to cover most of the questions you might ask about your Honda. Any questions not answered in the owner’s manual can be answered by your
Honda dealer. If your dealer doesn’t have an immediate answer, they should be able to get it for you.
If you have a difference of opinion with your dealer, please remember that each dealership is independently owned and operated. That’s why it’s important to work to resolve any differences at the dealership level. If the service personnel are unable to assist you, please discuss your concerns with the dealer management such as the Service Manager or
Dealer Owner.
If you need to contact American
Honda regarding your experiences with your Honda product or with
70
your dealer, please send your comments to the following address:
American Honda Motor Co., Inc.
Marine Division
Customer Relations Office
4900 Marconi Drive
Alpharetta, GA 30005-8847
Telephone (770)497 − 6400
M-F 8:30am7:00pm (Eastern Time
Zone)
05/12/21 14:11:17 31ZW6601_072
Please include the following information in your communication:
Your name, address and telephone number (complete with area code)
Model and complete serial number
Date of purchase
Name and location of selling dealer
Name and location of servicing dealer (if different)
A detailed description of your concerns
We will likely ask your Honda dealer to respond, or possibly acknowledge your comments directly.
TECHNICAL AND CONSUMER INFORMATION
Warranty Coverage
Your new Honda is covered by the following warranties:
Distributor’s Limited Warranty
Emission Control Warranty
Please read the warranty statements contained in this manual. There are responsibilities, restrictions, and exclusions that apply to these warranties.
To obtain warranty service you must take your Honda outboard engine, together with proof of original retail purchase date, at your expense, to a
Honda engine dealer or distributor authorized to sell that product in the
United States, Puerto Rico, or the
U.S. Virgin Islands.
It is important to realize that your warranty applies to defects in material or workmanship of your
Honda. Your warranty coverage does not apply to normal wear or deterioration associated with using your Honda outboard.
Your warranty coverage will not be voided if you choose to perform your own maintenance. However, you should have the proper tools and service information and be mechanically qualified. Failures that occur due to modifications, improper maintenance or service are not covered.
71
05/12/21 14:11:22 31ZW6601_073
TECHNICAL AND CONSUMER INFORMATION
Warranty Service
Please remember that recommended maintenance interval servicing is not included in your warranty coverage.
Additionally, your warranty does not apply to the normal wear of items
(such as spark plug(s), water pump, etc.).
As the owner of a Honda product, your servicing dealer may ask you to authorize an inspection. If the problem is covered under warranty, your dealer will perform any warranty repairs for you at no cost.
However, you may be responsible for additional non-warranty charges.
If you have questions about warranty coverage or the nature of the repair, it is best to talk to the service manager of your Honda dealer.
Sometimes, in spite of the best intentions of all concerned, a misunderstanding may occur. If you aren’t satisfied with your dealer’s
72
handling of the situation, we suggest you discuss your problem with the appropriate member of the dealership’s management team. If the problem has already been reviewed with the appropriate manager of the
Service, Parts, or Sales department, contact the owner of the dealership or their designated representative.
05/12/21 14:11:32 31ZW6601_074
TECHNICAL AND CONSUMER INFORMATION
Distributor’s Limited Warranty
This warranty is limited to Honda Outboard Motors distributed by American Honda Motor Co., Inc., Power Equipment
Division, 4900 Marconi Drive, Alpharetta, Georgia 30005-8847.
Products Covered by Warranty:
All Models: Model Year 2000 (Y) and Newer
Models BF115/BF130: All Model
Years
Models BF2 − BF90 − Model
Year 1999 and Earlier
Length of Warranty: (from date of original retail purchase)
NONCOMMERCIAL/ COMMERCIAL/RENTAL STATE/LOCAL/FEDERAL
NONRENTAL GOVERNMENT
36 months 12 months 24 months
36 months
24 months
To Qualify for This Warranty:
The Honda Outboard Motor must be purchased from
American Honda or a dealer authorized by American
Honda to sell Honda Outboard Motors in the United
States, Puerto Rico, or the U.S. Virgin Islands. This limited warranty applies to the first retail purchaser and each subsequent owner during the applicable warranty time period.
What American Honda Will Repair or Replace Under
Warranty:
American Honda will repair or replace, at its option, any part that is proven to be defective in material or workmanship under normal use during the applicable
12 months
12 months
24 months
24 months warranty time period. Warranty repairs and replacements will be made without charge for parts or labor. Anything replaced under warranty becomes the property of
American Honda Motor Company, Inc. All parts replaced under warranty will be considered as part of the original product and any warranty on those parts will expire coincidentally with the original product warranty.
To Obtain Warranty Service:
You must take your Honda Outboard Motor and proof of the original purchase date, at your expense, to any dealer who is authorized to service Honda Outboard Motors in the United States, Puerto Rico, or the U.S. Virgin Islands, during the dealer’s normal business hours.
73
05/12/21 14:11:44 31ZW6601_075
TECHNICAL AND CONSUMER INFORMATION
If you are unable to obtain warranty service, or are dissatisfied with the warranty service you receive, take the following steps: First, contact the owner of the dealership involved; normally this should resolve the problem. However, if you should require further assistance, write or call the Honda Marine Customer
Relations. Please see Contacting Honda
Exclusions:
This warranty does not extend to the following:
Conditions caused by lack of routine maintenance (as outlined in the owners manual)
Conditions caused by the use of propeller (s) that do not allow the outboard motor to run in its recommended full throttle rpm range
Operation inconsistent with the recommended operation/duty cycle (as outlined in the owners manual)
Parts affected or damaged by an accident, submersion and/or collision
Normal wear and tear
Fuel contamination and water entering engine through the fuel intake, air intake or exhaust system
Operation with fuels, oils, additives and lubricants which are not suitable for use in the product
Use in an application for which the outboard motor was not designed, such as racing or competitive use or any other misuse or neglect
74
Incorporation of unsuitable attachments or parts
The unauthorized alteration, improper installation and/ or rigging, or any causes other than defects in material or workmanship
Corrosion to steering system or electrical components, corrosion due to electrolysis, water born foreign chemicals, improper service or corrosion caused by damage or abuse
Reimbursement for towing charges, in and out of water charges, or technician travel time
Growth of marine organisms on motor surfaces, external or internal
Disclaimer of consequential damage and limitation of implied warranties:
American Honda disclaims any responsibility for loss of time or use of the outboard, revenue, or the equipment in which the outboard is installed,transportation, commercial loss, or any other incidental or consequential damage. Any implied warranties are limited to the duration of this written limited warranty. Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusions and limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
05/12/21 14:11:54 31ZW6601_076
TECHNICAL AND CONSUMER INFORMATION
Accessories and Replacement Parts
This warranty is limited to Honda Power Equipment parts,accessories and apparel when distributed by American Honda
Motor Co., Inc., 1919 Torrance Blvd., Torrance, California 90501-2746.
Products Covered by Warranty:
Accessories
Replacement Parts
Length of Warranty: (from date of original retail purchase)
Non Commercial Commercial/Rental Local/State/Federal
Government
12 months
6 months
3 months
3 months
3 months
3 months
To Qualify for This Warranty:
1.
The accessories or replacement parts must be
2.
purchased from American Honda, or a dealer, distributor or distributor’s dealer authorized by
American Honda to sell those products in the United
States, Puerto Rico, and the U.S. Virgin Islands.
You must be the first retail purchaser. This warranty is not transferable to subsequent owners.
What American Honda Will Repair or Replace Under
Warranty:
American Honda will repair or replace, at its option, any marine product accessories or replacement parts that are proven to be defective in material or workmanship under normal use during the applicable warranty time period.
Anything replaced under warranty becomes the property of American Honda Motor Company, Inc. All parts replaced under warranty will be considered as part of the original product and any warranty on those parts will expire coincidentally with the original product warranty.
Accessories and replacement parts, installed by a dealer who is authorized by American Honda to sell them, will be repaired or replaced under warranty without charge for parts or labor. If installed by anyone else, accessories and replacement parts will be repaired or replaced under warranty without charge for parts, but any labor charges will be the responsibility of the purchaser.
75
05/12/21 14:11:59 31ZW6601_077
TECHNICAL AND CONSUMER INFORMATION
To Obtain Warranty Service:
You must take the Honda Outboard Motor product accessory or replacement part or the outboard motor or boat on which the accessory or replacement part is installed, and proof of purchase, at your expense, to any
Honda Marine authorized service facility or dealer in the
United States, Puerto Rico, or the U.S. Virgin Islands, during normal business hours.
Exclusions:
This warranty does not extend to accessories or parts affected or damaged by accident and/or collision, normal wear, use in an application for which the product was not designed or any other misuse, neglect, incorporation or use of unsuitable attachments or parts, unauthorized alteration, improper installation, or any causes other than defects in material or workmanship of the product.
Disclaimer of consequential damage and limitation of implied warranties:
American Honda disclaims any responsibility for loss of time or use of the outboard motor, or the boat on which the product is installed, transportation, commercial loss, or any other incidental or consequential damage. Any implied warranties are limited to the duration of this written warranty. Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential
76
damages, so the above exclusions and limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
05/12/21 14:12:07 31ZW6601_078
TECHNICAL AND CONSUMER INFORMATION
Emission Control System Warranty
Your new Honda outboard engine complies with both the
U.S. EPA and State of California emission regulations.
American Honda provides the same emission warranty coverage for outboard engines sold in all 50 states.
YOUR WARRANTY RIGHTS AND OBLIGATION
California
The California Air Resources Board and American
Honda Motor Co., Inc. are pleased to explain the emission control system warranty on your 2001 and later
Honda outboard engine. In California, new outboard engines must be designed, built and equipped to meet
California’s stringent anti-smog emission standards in addition to the U.S. EPA emissions standards.
Other States
In other areas of the United States your outboard engine must be designed, built and equipped to meet the U.S.
EPA Emission Standard for spark ignited marine engines.
All States
American Honda Motor Co., Inc. must warranty the emission control system on your outboard engine for the period of time listed below provided there has been no abuse, neglect or improper maintenance of your outboard engine. Where a warranty condition exists, American
Honda Motor Co., Inc. will repair your outboard engine at no cost to you including diagnosis, parts and labor.
Your emission control system may include such parts as the carburetor or fuel injection system and catalytic converter. Also included may be hoses, connectors and other emission-related assemblies.
MANUFACTURER’S EMISSION CONTROL
SYSTEM WARRANTY COVERAGE:
The 2001 and later outboard engines are warranted for four years or 250 hours of operation, whichever comes first. However, warranty coverage based no the hourly period is only permitted for outboard engines equipped with appropriate hour meters. If any emission-related part on your outboard engine is defective under warranty, the part will be repaired or replaced by American Honda
Motor Co., Inc.
77
05/12/21 14:12:11 31ZW6601_079
TECHNICAL AND CONSUMER INFORMATION
OWNER’S WARRANTY RESPONSIBILITY:
As the outboard engine owner, you are responsible for the performance of the required maintenance listed in your owner’s manual. American Honda Motor Co., Inc.
recommends that you retain all receipts covering maintenance on your outboard engine, but American
Honda Motor Co., Inc. cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the outboard engine owner, you should, however, be aware that American Honda Motor Co., Inc. may deny you warranty coverage if your outboard engine or a part has failed due to abuse, neglect, improper maintenance, or unapproved modifications. You are responsible for presenting your outboard engine to a Honda Marine dealer as soon as a problem exists. The warranty repair should be completed in a reasonable amount of time, not to exceed 30 days. If you have any questions regarding your warranty rights and responsibilities, you should contact American Honda Motor Co., Inc., Marine
Division Customer Relations Office. Please see
Contacting Honda
WARRANTY COVERAGE:
Honda outboard engines manufactured after June 1, 2000 are covered by this warranty for a period of four years or
250 operating hours, whichever comes first, from the date of delivery to the retail purchaser. This warranty is transferred to each subsequent purchaser for the duration of the warranty period. Warranty repairs will be made without charge for diagnosis, parts and labor. All defective parts replaced under this warranty become the property of American Honda Motor Co., Inc. A list of
warranty parts is on page 80. Normal maintenance items,
such as spark plugs and filters, that are on the warranted parts list are warranted up to their required replacement interval only. American Honda Motor Co., Inc. is also liable for damages to other engine components caused by a failure of any warranted part during the warranty period.
Only Honda approved replacement parts will be used in the performance of any warranty repairs and they will be provided without charge to the owner. The use of replacement parts not equivalent to the original parts may impair the effectiveness of your engine’s emission control system. If such a replacement part is used in the repair or maintenance of your engine, and an authorized
Honda Marine dealer determines it is defective or causes a failure of a warranted part, your claim for your engine may be denied. If the part in question is not related to the reason that your engine requires repair, your claim will not be denied.
78
05/12/21 14:12:17 31ZW6601_080
TO OBTAIN WARRANTY SERVICE:
You must take your Honda outboard engine, along with your sales registration card or other proof of original purchase date, at your expense, to any Honda Marine dealer who is authorized by American Honda Motor Co.,
Inc. to sell and service that Honda marine product during his normal business hours. Claims for repair or adjustment found to be caused solely by defects in material or workmanship will not be denied because the engine was not properly maintained and used. If you are unable to obtain warranty service, or are dissatisfied with the warranty service you received, contact the owner of the dealership involved. Normally this should resolve your problem. However, if you require further assistance, write or call the Honda Marine Customer Relations
Office of American Honda Motor Co., Inc.
EXCLUSIONS:
FAILURES OTHER THAN THOSE RESULTING
FROM DEFECTS IN MATERIAL OR
WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY. THIS WARRANTY DOES NOT
EXTEND TO EMISSION CONTROL SYSTEMS OR
PARTS WHICH ARE AFFECTED OR DAMAGED BY
OWNER ABUSE, NEGLECT, IMPROPER
MAINTENANCE, MISUSE, MISFUELING,
IMPROPER STORAGE, ACCIDENT AND/OR
COLLISION. THE INCORPORATION OF, OR USE
TECHNICAL AND CONSUMER INFORMATION
OF, UNSUITABLE ATTACHMENTS, OR THE
UNAUTHORIZED ALTERATION OF ANY PART.
THIS WARRANTY DOES NOT COVER
REPLACEMENT OF EXPENDABLE
MAINTENANCE ITEMS MADE IN CONNECTION
WITH REQUIRED MAINTENANCE SERVICE
AFTER THE ITEM’S FIRST SCHEDULED
REPLACEMENT AS LISTED IN THE
MAINTENANCE SECTION OF THE PRODUCT
OWNER’S MANUAL, SUCH AS: SPARK PLUGS
AND FILTERS.
DISCLAIMER OF CONSEQUENTIAL DAMAGE
AND LIMITATION OF IMPLIED WARRANTIES:
American Honda Motor Co., Inc. disclaims any responsibility for incidental or consequential damages such as loss of time or the use of outboard engine, or any commercial loss due to the failure of the equipment; and any implied warranties are limited to the duration of this written warranty. This warranty is applicable only where the California or U.S. EPA emission control system warranty regulation is in effect.
79
05/12/21 14:12:26 31ZW6601_081
TECHNICAL AND CONSUMER INFORMATION
EMISSION CONTROL SYSTEM WARRANTY PARTS:
SYSTEMS COVERED BY THIS
WARRANTY:
Fuel Metering
Air Induction
Ignition
PARTS DESCRIPTION
Carburetor assembly, Throttle body, Fuel injector, Fuel pump, Fuel pressure regulator, Throttle position sensor, Intake air temperature sensor, Engine temperature sensor, Manifold absolute pressure sensor, Idle air control valve, Barometric pressure sensor, Fuel line solenoid valve, Intake manifold, Intake valves, and Oxygen sensor or Air fuel ratio sensor
Air intake duct, Crankcase breather tube, Positive crankcase ventilation valve, Vapor separator, Intake manifold tuning valve (Intake air bypass control valve)
Flywheel magneto, Ignition pulse generator, Ignition coil assembly, Ignition control module, Engine control module, Crankshaft position sensor, Spark plug cap,
Lubrication system
Crankcase Emission Control
Exhaust
VTEC System
Oil pump and internal parts
Oil filler cap
Exhaust manifold and Exhaust valves
VTEC valve
Miscellaneous Parts Tubing, fittings, seals, gaskets, and clamps associated with these listed systems.
＊ Covered up to the first required replacement only. See the Maintenance Schedule in the owner’s manual.
80
05/12/21 14:12:29 31ZW6601_082
WIRING DIAGRAM
81
05/12/21 14:12:33 31ZW6601_083
INDEX
Anode ............................................................................
Replacement ..............................................................
. 16
. 49
ARE YOU READY TO GET UNDER WAY?
............
. 20
ATTACHMENT ...........................................................
. 18
BEFORE OPERATION ................................................
. 20
BREAK-IN PROCEDURE ...........................................
. 22
Carburetor Modification for High Altitude
Operation ...................................................................
. 63
Centrifugal Clutch (SCHA/LCHA type) ......................
. 16
Choke Knob ...................................................................
. 11
Clamp Screws ................................................................
. 15
COMPONENT AND CONTROL LOCATIONS
CONSUMER INFORMATION
........
...................................
. 10
. 70
CONTROLS ..................................................................
. 11
CONTROLS AND FEATURES ....................................
CONTROLS AND FEATURE IDENTIFICATION
. 9
CODES ........................................................................
. 9
CRUISING ....................................................................
. 33
Customer Service Information ......................................
. 70
Distributor’s Limited Warranty .....................................
. 73
EMERGENCY STARTING .........................................
. 26
Emission Control System Information .........................
. 65
Emission Control System Warranty ..............................
. 77
Engine
Cover
REMOVAL AND INSTALLATION ...................
. 41
Retaining Strap ......................................................
. 13
Oil
Change ...................................................................
. 41
Level Check ..........................................................
Level Inspection Window .....................................
. 41
. 16
Recommendations .................................................
. 42
Engine Stop Switch and Switch Clip ............................
. 11
ENGINE WILL NOT DRIVE THE PROPELLER ......
. 59
ENGINE WILL NOT START ......................................
. 56
Fuel
Cap Vent Knob ..........................................................
. 15
RECOMMENDATIONS
Valve Lever
..........................................
...............................................................
. 48
. 13
Gear Oil Change ............................................................
. 43
HARD STARTING OR STALLS AFTER
STARTING ...............................................................
. 58
82
05/12/21 14:12:36 31ZW6601_084
INDEX
IMPORTANT SAFETY INFORMATION ....................
. 6
INSTALLATION ..........................................................
. 17
INSTALLATION POSITION ......................................
IS YOUR OUTBOARD MOTOR
. 17
READY TO GO?
......................................................
. 20
Lubrication Points .........................................................
. 44
MAINTENANCE SAFETY .........................................
MAINTENANCE SCHEDULE ...................................
. 37
. 39
MOORING, BEACHING, LAUNCHING ...................
. 34
OPERATION ................................................................
OTHER FEATURES ....................................................
. 22
. 16
OUTBOARD MOTOR SAFETY ...................................
. 6
Oxygenated Fuels ..........................................................
. 64
POWER REQUIREMENTS .........................................
. 17
Propeller Replacement ..................................................
. 50
Recoil Starter Grip .........................................................
. 13
Recoil Starter Rope Inspection ......................................
. 49
REFUELING .................................................................
. 47
REMOVAL FROM STORAGE ...................................
. 54
REVERSING THE OUTBOARD MOTOR ................
. 31
SAFE OPERATING PRECAUTIONS ........................
. 22
SAFETY LABEL LOCATIONS ....................................
. 8
Serial Number Locations ...............................................
. 62
SERVICING YOUR OUTBOARD MOTOR
Spark Plug Service
..............
........................................................
. 36
. 45
Specifications
Star Label
................................................................
......................................................................
. 69
. 67
STARTING THE ENGINE ..........................................
. 23
STEERING ....................................................................
. 32
Steering Friction Bolt ....................................................
STOPPING THE ENGINE
. 15
Emergency Engine Stopping .....................................
. 28
Normal Engine Stopping ...........................................
. 28
STORAGE ....................................................................
. 51
STORAGE PRECAUTIONS ........................................
. 53
STORAGE PREPARATION ........................................
. 51
Adding a Fuel Stabilizer ............................................
. 52
Cleaning ....................................................................
Draining the Fuel Tank and Carburetor ....................
. 51
. 52
Engine oil
Fuel
..................................................................
............................................................................
. 53
. 51
SUBMERGED MOTOR ...............................................
. 60
83
05/12/21 14:12:39 31ZW6601_085
INDEX
TAKING CARE OF UNEXPECTED PROBLEMS ....
. 56
TECHNICAL INFORMATION ...................................
. 62
THE IMPORTANCE OF MAINTENANCE ...............
. 36
Throttle Friction Knob (SHA/SCHA/LCHA type) ......
. 12
Throttle Grip (SHA/SCHA/LCHA type) ......................
. 12
Throttle Lever (SCAB type) ..........................................
. 12
THROTTLE OPERATION ..........................................
. 30
Tilt Lever .......................................................................
. 14
Transom Angle Adjusting Bolt .....................................
. 14
TRANSOM ANGLE ADJUSTMENT
TRANSPORTING
.........................
........................................................
. 22
. 55
WITH OUTBOARD MOTOR INSTALLED
ON BOAT .............................................................
. 55
WITH OUTBOARD MOTOR REMOVED
FROM BOAT .......................................................
. 55
WIRING DIAGRAM ....................................................
. 81
84
BF2D
Owner’s Manual
31ZW6610
00X31-ZW6-6100
N
BF2D6
2eY11000.2005.12
Printed in Japan ©2005 Honda Motor Co., Ltd. -All Rights Reserved
PANTONE 288 CVC DIC F101 BLACK
2006
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
