newway sp - Mothercare

newway sp - Mothercare
NEWWAY SP
Made in France by TEAM TEX
Rue du Claret - Z.I. de Montbertrand
38230 Charvieu - France
Tél. +33 (0)4 72 46 98 98 - Fax +33 (0)4 72 46 98 70
V5807
1
safety warnings
■ PLEASE READ THOROUGHLY BEFORE COMMENCING
INSTALLATION AS AN INCORRECT INSTALLATION COULD BE
DANGEROUS.
■ DO NOT USE THIS CHILD SEAT IN PASSENGER SEATS
EQUIPPED WITH AIRBAGS.
■ This child seat must only be installed in a forward facing
position in passenger seats.
Do not use on side facing or rear facing seats.
■ Never use this child seat without fastening the childs’
harness correctly, and never attempt to use it without
fastening it into the car as described in these
instructions.
■ Do not add to or modify the seat in any way.
■ In the event of an emergency it is important that the
child can be released quickly. This means that the buckle
is not fully tamperproof and so your child must be taught
never to play with the buckle.
■ Do not leave your child unattended in the seat at any
time.
■ It is recommended that this car seat should be changed
when it has been subjected to violent stresses in an
accident or has become badly worn. Periodically
inspect the harness for wear, paying particular attention
to the attachment points, stitching and adjusting
devices.
2
1
safety warnings
■ Ensure that no part of the seat is trapped in a door or
folding seat. If your car has a folding rear seat, ensure
that it is correctly latched in the upright position.
■ Car interiors can become very hot when in direct
sunlight, it is therefore recommended that the child seat
is covered when not in use. This prevents components,
particularly those attached to the child seat, becoming
hot and burning the child.
■ Luggage and other heavy or sharp objects should be
secured in the car. Loose objects are liable to cause
injury in the event of an accident.
■ The safest seating position for a child car seat is on the
rear seat of a vehicle.
3
2
getting to know your child seat
This child seat must only be installed in a forward facing
position.
This seat is classified as:
Group 1 for children weighing from 9kg to 18kg
(9 months - 4 years approx.)
Group 2 for children weighing from 15kg to 25kg
(4 - 6 years approx.)
Group 3 for children weighing from 22kg to 36kg
(6 - 11 years approx.)
SET UP FOR USE BY
15-25kg CHILDREN
GROUP 2
SET UP FOR USE BY
9-18kg CHILDREN
GROUP 1
SET UP FOR USE BY
22-36kg CHILDREN
GROUP 3
4
2
getting to know your child seat
HEAD
SUPPORT
DIAGONAL BELT CLIP
(for use in group 3 only,
see above. Store in a safe
place for future use.)
SHOULDER
PADS
DIAGONAL
BELT GUIDE
FOR GROUP 1
USE
BUCKLE AND
RELEASE
BUTTON
HARNESS
RELEASE
BUTTON
CROTCH
STRAP
HARNESS ADJUSTER
FRONT OF SEAT
LOCKING DEVICE
FOR HEAD SUPPORT
METAL
YOKE
REAR OF SEAT
5
3
the type of approved seat belt you must have
Your child seat can only be
installed forward facing
using a lap and diagonal
seat belt.
DIAGONAL BELT
DO NOT USE THIS CHILD SEAT
IN PASSENGER SEATS
EQUIPPED WITH AIRBAGS
LAP BELT
4
legal requirements
This child seat is approved to ECE R44.03 and is ONLY
suitable for use with a 3 point lap and diagonal seat belt,
approved to UN/ECE Regulation No.16 or other equivalent
safety standards.
front Seat
Anyone, especially children, travelling in the front seat of a
car must be properly restrained. Children under three years
must use a suitable approved restraint designed for their
weight.
rear Seat
All adults and children must use seat belts or child restraints
where they are fitted in the rear of a car and are available
for use.
If the appropriate restraint is not available, children from 3
years must wear an adult seat belt if available.
6
5
important notes
■ In an emergency your child can be released quickly by
pressing the red button on the harness buckle.
■ This user guide should be stored in the seat cover
pocket.
■ When the child seat is not in use, it is recommended that it
is fastened into the car with a seat belt to avoid being
thrown about in the event of an accident.
■ If you travel with passengers using both the front and rear
seats, the lighter occupants should be in the rear seats
and the heavier occupants in the front of the vehicle.
When a child is in the front seat, the lighter passenger
should be behind the child.
■ Do not allow the child seat to come into contact with
corrosive substances e.g. battery acid.
7
6
the harness
securing the harness
1
Place the left hand harness
connector behind the right
hand one. They should slot
together neatly.
2
Push the harness ends into
the hole in the buckle at the
top of the crotch strap. You
will hear and feel a ‘CLICK’
when it is secure. Check by
attempting to remove the
connectors by pulling the
webbing above and below
the buckle. Periodically
check that your child has
not released the buckle.
(To release the harness, press
the red button down.)
3
8
6
the harness
tightening the harness
Pull gently on the harness adjuster to take up any slack.
A loose harness is dangerous, so it should be checked every
time the seat is used.
It is recommended that there is just enough room to insert
two fingers between the shoulder straps and the childs’
chest.
loosening the harness
If the harness is too tight,
loosen it by first pressing the
tab at the front of the seat,
and then pulling both
straps, as shown. Do not pull
on the shoulder pads, as
these are fixed in length.
9
6
the harness
adjusting the shoulder height
The harness has 3 height
positions.
The straps should go into the
slots nearest to the top of
your child’s shoulders.
1
IMPORTANT
If your child's shoulders are
between two pairs of slots,
always use the higher
position.
To adjust the shoulder straps
of the harness, remove one of
the shoulder straps from the
metal retaining yoke located
at the back of the seat.
Leave the other one in place
for reference.
2
Pull the shoulder strap
through the harness slot in the
shell and cover, then pull
through the shoulder pad.
3
10
6
the harness
Pull shoulder pad back
through harness slot in cover
and shell, and re-locate to
desired harness slot.
4
Feed the shoulder strap back
through the shoulder pad,
then through the same slot,
and re-attach to metal yoke
at rear. Repeat the same
prodedure for the shoulder
strap and pad on the other
side. Make sure there are no
kinks or twists in the straps.
5
7
using the head support
The adjustable head
support is designed to
provide side impact
protection for your child
(when the seat is used with
the backrest).
The head support should be
positioned just above your
child’s shoulders.
1
11
7
using the head support
To adjust the height,
unscrew the red locking
device located at the top
back of shell. Move up or
down to the desired
position. Then re-tighten the
red locking device, making
sure that there is no
movement in the head
support.
2
The head support can be
removed to wash the cover.
Please see care &
maintenance section.
8
fitting your child seat into your car
WARNING:
Do not use this child seat in passenger seats fitted with airbags.
Do not use on rear-facing or side-facing vehicle seats.
To set up for use from 9kg to 18kg
Place the child’s car seat
on a passenger seat with a
3 point seat belt.
Make sure the child seat is
facing towards the front of
the car.
1
12
8
fitting your child seat into your car
Pull the lap and diagonal sections of
the car seat until fully extended.
Guide the seat belt around the side
panel of the car seat making sure
that the lap belt is below the arm
rest of the seat base.
2
Then feed both lap and diagonal
belt into the side slot, around the
plastic back panel (over the harness)
and back through the opposite slot.
Pull the belt around the seat and
fasten in the normal way making sure
that the lap section is below the arm
rest and the diagonal section goes
through the red guide. Make sure
that there are no kinks or twists in the
car seat belt.
3
Put your knee on the child seat to
push it right down into the car seat.
You should then pull upwards
simultaneously on both the lap and
diagonal belts.
Your car seat should now be fixed
securely.
To check that the seat is fixed
securely, tug the top of the shoulder
straps there should be little or no
forwards movement.
4
13
8
fitting your child seat into your car
To set up for use from 15kg to 25kg
Your child will be secured
using the vehicle’s seat belt.
It will therefore be
necessary to remove the
harness fitted to the child
seat before use.
Turn the seat upside down
and remove the blue plastic
clips from the ends of both
of the shoulder straps.
Feed the straps through the
bottom of the child seat.
1
2
2
a
Pull the shoulder straps through the buckle connectors, then
pull both shoulder straps and shoulder pads through the
back of the seat.
14
8
fitting your child seat into your car
Remove the shoulder straps
from the metal yoke.
3
Pull the harness adjuster
until the metal yoke is tight
against the back of the seat
base.
4
The end of the harness
adjuster which is left can be
fed back into the slot in the
cover for storage for future
use.
5
Remove the crotch strap by
twisting and feeding the
metal retaining keeper
through the BOTTOM of the
child seat and up through
the seat’s upholstery.
15
8
fitting your child seat into your car
To fit the child’s car seat,
place it on a passenger
seat with a 3 point seat belt.
Make sure it is facing
towards the front of the
vehicle.
6
Pull the lap and diagonal
sections of the car seat belt
across and secure it in the
normal way.
Make sure that there are no
kinks or twists in the car seat
belt.
The lap belt should be
routed under both the arm
rests of the child seat and
the diagonal belt routed
over the armrest as shown.
The diagonal belt will be
kept away from the child’s
neck by passing under the
head support.
7
16
8
fitting your child seat into your car
To set up for use from 22kg to 36kg
1
The child seat can be used as
a ‘booster seat’ by removing
the back section. If you have
not already removed the
child’s harness, do this first.
(Refer to diagrams 1 to 5 on
pages 14 and 15). The back
section of the seat is removed
by pushing the back of the
seat away from the base of the
seat.
2
Attach the diagonal belt
clip, by threading the loose
strap through the slot at the
side of the seat base.
IMPORTANT
This should be fitted on the
same side as the vehicle
seat belt buckle when the
seat is installed in the car.
17
8
fitting your child seat into your car
Place the child car seat on the
passenger seat with a 3 point
seat belt. Make sure it is facing
towards the front of the car.
3
Pull the lap and shoulder
sections of the vehicle seat
belt across and secure it in the
normal way.
The lap belt should be routed
under both the arm rests of the
child seat,
and the diagonal belt routed
over the armrest as shown.
4
The red belt clip can be used
to position the diagonal belt
securely on the childs shoulder,
away from the neck. Pass the
strap behind the childs back,
so the clip rests on the childs
shoulder, then feed the
diagonal belt through the clip.
Adjust the strap length so the
clip holds the belt securely on
the shoulder.
WARNING: PLEASE ENSURE THAT
THE RED BELT CLIP AND
WEBBING DO NOT INTERFERE
WITH THE VEHICLE SEAT BELT
5
18
9
final checklist
However safe a child seat is, however well built it is, your
childs’ safety depends on you.
Read this final checklist once you have fitted your child seat
in your car.
1.
Check that you have adjusted the harness to suit your child.
A fitting for winter clothes will be too loose for a child wearing
summer clothes.
2.
Check you have installed your child seat properly using a 3
point lap and diagonal belt.
See section 8, fitting your child seat into your car.
3.
Check that your child seat is secure before each journey.
REMEMBER: mis-using your child seat will reduce the
protection and safety you offer your child.
IF YOU ARE UNSURE ABOUT THE FIT OF YOUR CHILD SEAT
PLEASE VISIT YOUR LOCAL MOTHERCARE STORE FOR ADVICE
19
10
returning the seat to its configuration for younger children
AFTER YOU HAVE USED THE CHILD SEAT FOR AN OLDER
CHILD (GROUP 2 OR 3) YOU MUST FOLLOW THE
GUIDELINES BELOW WHEN RE-USING THE SEAT FOR A
YOUNGER (GROUP 1) CHILD.
1
Remove the diagonal belt
clip.
2
Re-fit the back of the child
seat. To do this, lay the seat
back flat. Engage the two
locating pegs and lift
upwards as shown.
Then press down firmly on
the back of the seat so that
the two pegs engage
securely.
3
Feed the metal keeper of
the crotch strap through
the slot in the cover and
through the rear of the two
slots in the plastic base.
20
10
returning the seat to its configuration for younger children
4
Make sure that the metal
keeper is securely engaged
against the seat base.
5
Re-attach the shoulder
straps to the metal yoke as
shown.
6
Feed both shoulder straps
and pads through the
harness slots at the correct
height for your child.
The shoulder pads are an
important safety feature,
and must be fitted with the
friction side against your
child’s shoulders.
7
Feed the shoulder straps
through the buckle
connectors, then into the
slots in cover and base at
the sides of the seat.
21
10
returning the seat to its configuration for younger children
Fit the blue plastic clips
onto the ends of the
shoulder harnesses. Check
all fittings are secure before
use.
8
11
care of your product
removing the fabric cover
■ The fabric cover can be
removed from the seat.
Remove the child’s harness
refer to diagrams 1 to 5 on
pages 14 and 15.
Then release the elasticated
edges of the cover from the
seat.
Remove the head support by
turning the red locking device
whilst applying downward
pressure as shown.
cleaning the seat
■ The harness and plastic parts can be sponged with a mild
detergent and warm water.
Ensure no soap gets into the buckle or adjusters.
Do not use chemical cleaners or bleach on the harness straps.
Dry thoroughly before use.
22
accessories & replacement parts
12
Your child seat and its cover have been carefully designed,
manufactured and tested to the highest safety standards.
Do not put your child’s safety at risk by using without a seat cover. The
seat cover should not be replaced with any other than the one
recommended by the manufacturer, because the cover constitutes an
integral part of the restraint performance.
The safety of this seat may be compromised by the use of accessories
not approved by manufacturer.
The replacement parts listed below are available for your product. In
the event that you require any of these parts, please contact the
manufacurer (details on back page).
HEAD SUPPORT
BACK
COVER
DIAGONAL BELT CLIP
SHOULDER
PADS
BELT
GUIDES
BUCKLE SET
BUCKLE PAD
BOOSTER
COVER
13
Replacement
Parts
Booster cover
Back unit cover
Belt clip
Head support cover
Shoulder pads and
harness
Buckle set
Belt guides
customer care
If you have a problem with this product or require
replacement parts, please contact the manufacturer
(details on back page).
23
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement