Panasonic SCPM53 User manual

Add to My manuals
16 Pages

advertisement

Panasonic SCPM53 User manual | Manualzz
Operating Instructions
CD Stereo System
The illustrations show SC-PM53
Model No.
SC-PM53
SC-PM54
SC-PM54 is available in Continental Europe, Australia and
New Zealand only.
Table of contents
Caution for AC Mains Lead ................ 2
Safety precautions ............................. 3
Disc information ................................. 3
Placement of speakers....................... 3
Getting started .................................... 4
Overview of controls .......................... 6
Discs .................................................... 7
Cassette tape ...................................... 9
Radio.................................................... 10
Timer .................................................... 11
Sound adjustment .............................. 12
External unit ........................................ 13
Troubleshooting guide ....................... 14
Specifications ..................................... 15
Maintenance ........................................ 15
When moving the unit ........................ 15
Before connecting, operating or adjusting this product,
please read the instructions completely.
Please keep this manual for future reference.
SUPPLIED ACCESSORIES
Please check and identify the supplied accessories.
Use numbers indicated in parentheses when asking for
replacement parts. (As of December 2005)
1 x Remote control
1 x AC mains lead
(N2QAYB000008)
(For United Kingdom:
K2CT3CA00004)
1 x FM indoor antenna
(For Australia and N.Z.:
K2CJ2DA00010)
(RSA0007-L)
1 x Antenna plug adaptor
(For United Kingdom:
K1YZ02000013)
2 x Remote control
batteries
(For others:
K2CQ2CA00002)
1 x AM loop antenna
Note:
“EB” on the packaging indicates the United Kingdom.
Operations in these instructions are described using
remote control, but you can do the operations with
the main unit if the controls are the same.
(N1DAAAA00001)
Unless otherwise indicated, illustrations in these
operating instructions are of SC-PM53 for the
United Kingdom and Continental Europe.
Your unit may not look exactly as illustrated.
E
EB GN
RQTV0102_4B_n.indd 1
RQTV0102-4B
3/5/07 2:56:23 PM
Dear customer
Thank you for purchasing this product.
For optimum performance and safety, please read these
instructions carefully.
These operating instructions are applicable to the following
system.
System
SC-PM53
SC-PM54
Main unit
Speakers
SA-PM53
SB-PM53
SA-PM54
SB-PM54
Caution for AC Mains Lead
Back of product
Inside of product
Tuotten sisällä
Produktets
innside
Information on Disposal for Users of Waste Electrical
& Electronic Equipment (private households)
RQTV0102
This symbol on the products and/or
accompanying documents means that used
electrical and electronic products should not be
mixed with general household waste. For proper
treatment, recovery and recycling, please take
these products to designated collection points,
where they will be accepted on a free of charge basis.
Alternatively, in some countries you may be able to return
your products to your local retailer upon the purchase of
an equivalent new product.
Disposing of this product correctly will help to save valuable
resources and prevent any potential negative effects on
human health and the environment which could otherwise
arise from inappropriate waste handling. Please contact
your local authority for further details of your nearest
designated collection point.
Penalties may be applicable for incorrect disposal of this
waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment,
please contact your dealer or supplier for fur ther
information.
Information on Disposal in other Countries outside the
European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your
local authorities or dealer and ask for the correct method
of disposal.
This product may receive radio interference caused by
mobile telephones during use. If such interference is
apparent, please increase separation between the product
and the mobile telephone.
Figure A
Figure B
Fuse cover
Figure A
Figure B
Fuse
(5 ampere)
Fuse
(5 ampere)
2
RQTV0102_4B_n.indd 2
3/5/07 2:56:27 PM
Disc information
• This unit can play MP3 files and CD-DA format audio CD-R/RWs
that have been finalized.
• It may not be able to play some CD-R/RWs depending on the
condition of the recording.
• Do not use irregularly shaped discs.
• Do not use discs with labels and stickers that are coming off or with
adhesive exuding from under labels and stickers.
• Do not attach extra labels or stickers on the disc.
• Do not write anything on the disc.
CD
• This unit can access up to 99 tracks.
• Choose a disc with this mark:
Using DualDiscs
The “CD” sides of DualDiscs do not meet the CD-DA standard so it
may not be possible to play them on this unit.
MP3
English
• Files are treated as tracks and folders are treated as albums.
• This unit can access up to 999 tracks, 255 albums and 20 sessions.
• Disc must conform to ISO9660 level 1 or 2 (except for extended
formats).
• To play in a certain order, prefix the folder and file names with the
3-digit numbers in the order you want to play them.
Not doing the following will cause damage to the unit.
• “GOODBYE” is displayed when the unit turns off. Remove the
mains plug after this display disappears.
OPEN/CLOSE
English
• Always press [OPEN/CLOSE 0] to insert or remove a disc.
• Do not push or pull out the tray by hand as this may cause an
accident.
• Place the disc label-up in the center or tray.
• Insert only one disc into each tray.
Placement of speakers
SC-PM53
Speakers are designed
identically so that no
left or right channel
orientation is necessary.
SC-PM54
Tweeter
Place the speakers so
that the tweeter is on the
inside.
Use only the supplied speakers.
The combination of the main unit and speakers provide the best
sound. Using other speakers can damage the unit and sound
quality will be negatively affected.
Caution
• Use the speakers only with the recommended system.
Failure to do so can damage the amplifier and speakers,
and can cause fire. Consult a qualified service person if
damage occurs or if a sudden change in performance is
apparent.
• Do not attach these speakers to walls or ceilings.
RQTV0102_4B_n.indd 3
RQTV0102
Note
• Keep your speakers at least 10mm away from the system for proper
ventilation.
• These speakers do not have magnetic shielding. Do not place
them near televisions, personal computers or other devices easily
influenced by magnetism.
• To avoid damage to the speakers, do not touch the speaker cones
if you have taken the nets off.
3
3/5/07 2:56:28 PM
Getting started
Step 1 - Making the connections
Connect the AC mains lead cord only after all other connections have been made.
1 Connect the AM loop antenna.
AM loop antenna
NT
AM A OP
O
EXT L
2 Connect the FM indoor antenna.
T
FM AN
75
Stand the antenna up on its base. Keep the loose antenna cord
away from other wires and cords.
Adhesive
tape
FM indoor
antenna
Tape the antenna to a wall or column, in a
position with least amount of interference.
To household
mains socket
3 Connect the speaker cords.
4 Connect the AC mains lead.
For Europe
Red (ª)
Red
Black
(·)
FOR THE UNITED KINGDOM ONLY
READ THE CAUTION FOR THE AC MAINS LEAD
ON PAGE 2 BEFORE CONNECTION.
The included AC mains lead is for use with this unit
only. Do not use it with other equipment.
L
R
Insertion of connector
Black
Appliance inlet
Connector
(6 )
For others
Black (·)
Blue (·)
Red (ª)
Even when the connector is perfectly inserted,
depending on the type of inlet used, the front part of
the connector may jut out as shown in the drawing.
However there is no problem using the unit.
Gray
Red
Gray
(ª)
4
Blue
Black
RQTV0102
L
R
HIGH (6
)
LOW
(6 )
Incorrect connection can damage the unit.
RQTV0102_4B_n.indd 4
3/5/07 2:56:33 PM
Optional antenna connections
FM outdoor antenna
AM outdoor antenna
FM outdoor antenna
(not included)
NT
AM A OP
O
EXT L
T
T
FM AN
75
NT
AM A OP
O
EXT L
FM AN
75
AM outdoor antenna
(not included)
AM loop antenna
(included)
75 Ω coaxial cable
(not included)
(Only for the U.K.)
•
•
•
•
English
Use the antenna
plug adaptor
(included).
Never use an outdoor antenna during a lightning storm.
You can connect the FM outdoor antenna for better reception. Please consult your dealer for installation.
Disconnect the FM indoor antenna if an FM outdoor antenna is installed.
Connect the AM outdoor antenna without removing the AM loop antenna. Run 5 to 12 m of vinyl-covered wire horizontally
along a window or other convenient location.
Step 2 - Inserting batteries into the remote control
English
AA/R6/LR6
■ Batteries
• Insert so the poles (+ and –) match those in the remote control.
• Remove if the remote control is not going to be used for a long period of
time. Store in a cool, dark place.
• Do not use rechargeable type batteries.
• Mishandling of batteries in the remote control can cause electrolyte
leakage, which may cause a fire.
Do not:
• mix old and new batteries.
• use different types of batteries at the same time.
• heat or expose to flame.
• take apart or short circuit.
• attempt to recharge alkaline or manganese batteries.
• use batteries if their covering has been peeled off.
■ Use
• Aim at the remote control sensor, avoiding obstacles, at a maximum
range of 7 m directly in front of the unit.
Refer to page 6 for remote control signal sensor position.
Step 3 - DEMO function
When the unit is first plugged in, a demonstration of its functions may be
shown on the display.
If the demo setting is off, you can show a demonstration by selecting
“DEMO ON”.
Press and hold [–DEMO, 7].
The display changes each time the button is held down.
DEMO OFF
DEMO ON
RQTV0102
While in standby mode, select “DEMO OFF” to reduce power
consumption.
5
RQTV0102_4B_n.indd 5
3/5/07 2:56:40 PM
Overview of controls
Main unit
Refer to numbers in parentheses for page reference.
Top of unit
Headphone jack ( )
Avoid listening for prolonged
periods of time to prevent
hearing damage.
Plug type: 3.5 mm stereo
(not included)
Cassette lid (9)
Cassette lid open (9)
AC supply indicator (AC IN)
This indicator lights when the unit is connected
to the AC mains supply.
1 Standby/on switch (y/l) (15)
Press to switch the unit from on to standby
mode or vice versa. In standby mode, the unit is
still consuming a small amount of power.
Display panel
Remote control sensor
6 Music port selection (13)
Stop/Demo (5, 9)
7 Recording start/pause (9, 13)
2 Disc play/pause (7)
3 Tape play (9)
4 Bass selection (12)
Music port jack (13)
5 Treble selection (12)
Disc skip/search, tape fast-forward/
rewind, tune/preset channel selection,
time adjustment (9)
8 Tuner/Band selection (10)
9 Volume control
! H.BASS selection (13)
Checking disc position (8)
Changing disc (7)
Disc tray open/close (7)
Disc selection (7)
Disc tray (7)
Remote control
Buttons such as 1 function the same as the controls on the main unit.
Sleep timer (11)
1
Auto off
Clock/Timer (11)
Play timer/Record timer (11)
Display (8, 10)
Dimmer
Disc (7)
Program (8)
Numeric (7, 10)
Clear (8)
Repeat (8)
Album selection
(7)
2
6
Delete (8)
Disc skip/search, tape fastforward/rewind, tune/preset
channel selection, time
adjustment (7, 10, 11)
8
3
Stop (7)
9
Treble/bass
adjustment (12)
RQTV0102
4
!
Re-Master (13)
6
RQTV0102_4B_n.indd 6
7
Enter (8)
This function allows you to
turn off the unit in disc or
tape mode only after left
unused for 10 minutes.
The setting is maintained
even if the unit is turned
off.
Dims the display panel.
5
Preset EQ (12)
Surround (13)
Muting
Play mode (7, 9, 10)
Mutes the sound.
• Press the button to activate.
• Press again to cancel.
3/5/07 2:56:42 PM
Discs
English
Numeric
buttons
Disc trays
Play Mode function
CD
CD
MP3
Press [y] to turn the unit on.
1
2
3
Press [1 3~ 5 3] to select your desired tray.
Press [OPEN/CLOSE 0] to open the disc tray and
then load the disc. Press [OPEN/CLOSE 0] again to
close the tray.
Label must
face upward
Tray number
Disc tray
1
2
3
MP3
Press [CD 6] and then [STOP 7].
English
Basic play
Press [DISC] and (within 10 seconds) press [1 ~ 5] to
select the disc.
Press [PLAY MODE] to select the desired mode.
Mode
To play
1-DISC
one selected disc.
1DISC
ALL-DISC
all discs in trays, e.g., 4→5→1→2→3.
ALL DISC
1-TRACK
1TR
Adjust the volume.
To
Action
stop the disc
Press [STOP 7].
1-ALBUM
pause play
Press [CD 6]. Press again to
resume play.
1ALBUM
skip tracks
Press [4/REW/4] or [3/FF/¢]
during play or pause.
search through tracks
Press and hold [4/REW/4] or
[3/FF/¢] during play or pause.
CD
MP3
1-DISC RANDOM
If the unit is on standby mode and a
disc is loaded, press [CD 6] or
[1 3 ~ 5 3] to start play.
skip album
Press [ALBUM
or
] in the play
mode.
or
] once and
Press [ALBUM
then the numeric buttons in the stop
mode.
MP3
Changing disc (CD CHANGE)
CD
MP3
While one disc is playing, you can change the discs in other
trays (except in All-Disc random play or program play).
1 Press [CHANGE 0].
2
3
4
Press [1 3~ 5 3] to select the tray.
Change the disc.
Press [CHANGE 0] again to close the tray.
RQTV0102_4B_n.indd 7
one selected album on the selected
disc.
or
] to select
Press [ALBUM
the album.
one selected disc randomly.
1DISC RND
1-ALBUM RANDOM
1ALBUM RND
direct play
one selected track on the selected
disc.
Press the numeric buttons to select
the track.
MP3
ALL-DISC RANDOM
all tracks in one selected album
randomly.
or
] to select
Press [ALBUM
the album.
all loaded discs randomly.
ALL DISC RND
Note
• During any random play, you cannot skip to tracks that have been
played.
• CD
During 1-DISC RANDOM or ALL-DISC RANDOM play, you can
search forward or backward only within the current track.
RQTV0102
Press [CD 6] to start play.
4
5
7
3/5/07 2:56:44 PM
Discs (continued)
Checking which discs are in the trays (CD CHECK)
CD
Program play
This function allows you to program up to 24 tracks.
MP3
CD
Press [CD CHECK].
1
1
2
3
4
1
2
3
4
5
CD CHECK
5
Press the button again to close the trays.
2
Note
• The tray with a disc being played will not open.
• If the player is stopped, all trays will open.
• Do not remove or insert discs during disc check.
• Do not pull out the trays during disc check.
• 8 cm discs cannot be checked.
This function allows you to display the information of the
current track.
Press [DISPLAY] repeatedly during play or pause mode.
CD
Remaining time
1
2
3
4
5
6
7
MP3
Elapsed time
Remaining
time
ID3 (Artist)
Album name
ID3 (Track)
Press [PROGRAM].
Press [DISC].
(Within 10 seconds or so)
Press [1~5] to select your desired disc.
Press the numeric buttons to select your desired
track.
Repeat steps 3 to 5 to program other tracks.
Press [CD 6] to start play.
MP3
Display function
Elapsed time
6
7
Press [CD 6] and then [STOP 7].
Track name
ID3 (Album)
Note
• Maximum number of displayable characters: approximately 30
• This unit supports ver. 1.0 & 1.1 ID3 tags. Text data that is not
supported will not be displayed.
• ID3 is a tag embedded in MP3 tracks to provide information about
the track.
Advanced play
8
9
Press [CD 6] and then [STOP 7].
Press [DISC].
(Within 10 seconds or so)
Press [1~5] to select your desired disc.
Press [STOP 7].
Press [PROGRAM].
Press [ALBUM
or
] to select your desired
album.
Press [3/FF/¢] once and then the numeric buttons
to select your desired track.
Press [ENTER].
Repeat steps 6 to 8 to program other tracks.
Press [CD 6] to start play.
To
replay the program
Press [PROGRAM] then [CD 6].
check program
contents
Press [ /REW/4] or [ /FF/¢] when
“PGM” is displayed in the stop mode.
To check while programming, press
[PROGRAM] twice after “PGM” appears,
then press [ /REW/4] or [ /FF/¢] .
Direct access play
This function allows you to start play from a specific track.
Action
cancel program mode Press [PROGRAM] in the stop mode.
add to the program
CD
Repeat step 3 to 5 in the stop mode.
CD
MP3
Press the numeric buttons to select and play your
desired track.
clear the last track
MP3
1
2
Press [ALBUM
or
] to select the album.
Press [3/FF/¢] once and then the numeric buttons
to select and play your desired track.
For two-digit track, press [h10] once, and then the two
digits.
For three-digit track, press [h10] twice, and then the three
digits.
Note
This function does not work during any random/program mode.
Repeat play
You can repeat program play or other selected play mode.
RQTV0102
CD
8
Repeat steps 6 to 8 in the stop mode.
MP3
Press [DEL] in the stop mode.
clear all programmed Press [CLEAR] in the stop mode. “CLR ALL”
tracks
is displayed.
Note
• When you try to program more than 24 tracks “PGM FULL”
appears.
• During program play, skipping is always in the programmed order,
whether forward or backward.
• You cannot program CD-DA together with MP3 tracks.
• You cannot change or open other trays during program play mode.
• CD
During program play, you can search backward or forward only
within the current track.
• MP3
The program memory is cleared when you change a disc or open
a disc tray.
Press [REPEAT] before or during play.
“REPEAT ON” and “ ” are displayed.
To cancel
Press [REPEAT] again.
“REPEAT OFF” is displayed and “ ” is cleared.
RQTV0102_4B_n.indd 8
3/5/07 2:56:46 PM
Cassette tape
Recording
Use normal position tapes.
High position and metal position tapes can be used, but this
unit will not be able to record or erase them correctly.
Preparation
Wind the leader tape so that recording can begin
immediately.
Top of unit
Cassette lid
Recording the radio
1
2
3
Insert the cassette to be recorded.
Tune to the required station (refer to page 10).
Press [¶ REC/8] to start recording.
The buttons described for “Cassette tape” are mainly for
the main unit unless indicated otherwise.
Basic play
5
Press [CD 6] and then [–DEMO, 7].
Press [OPEN/CLOSE 0] to insert the disc. Press
again to close.
Press [PLAY MODE] on the remote control to select
your desired mode (refer to page 7).
Press [¶ REC/8] to start recording.
Press [0] and insert the cassette.
Insert inside
the guides
Forward side
Close the lid by hand.
Press [TAPE 3] to start play.
1
2
3
English
Recording programmed tracks
"
2
3
4
Insert the cassette to be recorded.
Insert the cassette to be recorded.
Program the tracks you want (refer to page 8).
Press [¶ REC/8] to start recording.
Other basic operations
To play the other side of the cassette, turn the cassette over.
To
Action
stop tape playback
Press [–DEMO, 7].
start one-touch play
Press [TAPE 3] when the unit is OFF with
the cassette loaded.
fast-forward and
rewind
Press [4/REW/4] or [3/FF/¢] in the
stop mode.
Note
• Tapes exceeding 100 minutes are thin and can break or get caught
in the mechanism.
• Endless tapes can get caught up in the deck’s moving parts if used
incorrectly.
TPS (Tape Program Sensor)
This function enables you to search the beginning of a track,
up to a maximum of 9.
Press [4/REW/4] or [3/FF/¢] during play.
Play resumes from the track found.
Note
TPS may not function properly:
• with short silent parts
• when noise occurs between tunes
• if silent parts found within tunes
To
Action
erase a recorded
sound
1) Insert the cassette to be recorded.
2) Press [TAPE 3] and then
[–DEMO, 7].
3) Press [¶ REC¥8].
stop recording
Press [–DEMO, 7].
stop recording
temporarily
1) Press [¶ REC¥8].
2) Press again to resume recording.
record on the other
side of the tape
Turn the cassette over and press
[¶ REC¥8].
You can perform the same operation of [¶ REC¥8] on the
main unit by pressing [REC ¶¥8] and [TAPE] simultaneously
on the remote control.
You attention is drawn to the fact that recording pre-recorded
tapes or discs or other published or broadcast material may
infringe copyright laws.
Erasure prevention
The illustration shows how to remove the tabs to prevent
recording. To record on the tape again, cover as shown.
Side A
Tab for
side B
Tab for
side A
To re-record
Normal tape
Adhesive tape
RQTV0102
1
1
2
3
English
Recording discs
9
RQTV0102_4B_n.indd 9
3/5/07 2:56:47 PM
Radio
RDS broadcasting (For Europe)
Numeric
buttons
Enable you to display the name of a broadcasting station or
a program type.
Press [DISPLAY] to display:
Program Type (PTY)
Station Name (PS)
Frequency display
RDS displays may not be available if reception is poor.
Program type displays
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
M-O-R- M
LIGHT M
CLASSICS
OTHER M
WEATHER
FINANCE
CHILDREN
SOCIAL A
RELIGION
PHONE IN
TRAVEL
LEISURE
JAZZ
COUNTRY
NATIONAL
OLDIES
FOLK M
DOCUMENT
TEST
ALARM
M-O-R- M = “Middle-of-the-road music”
Memory preset
Up to 15 stations can be set in both the FM and AM bands.
Preparation
Press [TUNER/BAND] to select “FM” or “AM”.
Automatic presetting
Press and hold [PROGRAM] to start presetting.
Manual presetting
Manual tuning
1
2
3
Press [TUNER/BAND] to select “FM” or “AM”.
Press [PLAY MODE] to select “MANUAL”.
Press [4/REW/4] or [3/FF/¢] to select the
frequency of the required station.
1
2
3
4
5
Press [PLAY MODE] to select “MANUAL”.
Press [4/REW/4] or [3/FF/¢] to tune to the
required station.
Press [PROGRAM].
Press numeric buttons to select a channel.
The station occupying a channel is erased if another
station is preset in that channel.
Repeat steps 2 to 4 to preset more stations.
Selecting a preset station
Press numeric buttons to select the channel.
For channels 10 to 15 press [h10], then the two digits.
“ST” is displayed when a stereo FM broadcast is being
received.
To tune automatically
Press [4/REW/4] or [3/FF/¢] for a moment until the
frequency starts changing rapidly. The unit begins auto
tuning, stopping when it finds a station.
• Auto tuning may not function when there is excessive
interference.
• To cancel auto tuning, press [4/REW/4], [3/FF/¢] or
[STOP 7].
RQTV0102
To improve FM sound quality
Press and hold [PLAY MODE] to display “MONO”.
To cancel
Press and hold [PLAY MODE] again until “MONO”
disappears.
• MONO is also cancelled if the frequency is changed.
• Turn off “MONO” for normal listening.
OR
1
2
Press [PLAY MODE] to select “PRESET”.
Press [4/REW/4] or [3/FF/¢] to select the
channel.
AM allocation setting
By main unit only
This system can also receive AM broadcasts allocated in
10 kHz steps.
To change the step to 9 kHz to 10 kHz
1
2
Press and hold [TUNER/BAND].
After a few seconds the display changes to a flashing
display of the current minimum frequency.
Continue to hold down [TUNER/BAND].
• When the minimum frequency changes, release the
button. To return to the original step, repeat the above
steps.
• After the setting is changed, any previously preset
frequency will be cleared.
10
RQTV0102_4B_n.indd 10
3/5/07 2:56:49 PM
Timer
Using the play or record timer
You can set the timer to come on at a certain time to wake
you up (play timer) or to record from the radio or a music port
source (record timer).
Timer
Action
Play timer
Prepare the music source you want to listen
to; cassette, disc number (1-5), radio or
music port source, and set the volume.
Record timer
Check the cassette’s erasure prevention
tabs (refer to page 9), insert the cassette and
tune to the radio station (refer to page 10) or
select music port source (refer to page 13).
Setting the clock
This is a 24-hour clock.
[CLOCK/TIMER] to select “CLOCK”.
1 Press
Each time you press the button:
˚ REC
˚ PLAY
CLOCK
Original display
1
English
Preparation
Turn the unit on and set the clock.
Press [CLOCK/TIMER] repeatedly to select your
desired timer.
CLOCK
˚ PLAY
˚ REC
Original display
2
Within 5 seconds, press [4/REW/4] or [3/FF/¢]
to set the time.
3
Press [CLOCK/TIMER] again to confirm.
Start time
Record timer indicator
Play timer indicator
3
4
English
2
Within 5 seconds, press [4/REW/4] or [3/FF/¢]
to set the starting time.
Press [CLOCK/TIMER] to confirm.
Repeat steps 2 and 3 to set the finishing time.
Finish time
Displaying the clock
Press [CLOCK/TIMER] to display the clock for a few
seconds.
Using the sleep timer
˚ PLAY
This function enables you to turn off the unit automatically
after the set time.
Press [SLEEP] repeatedly to select your desired time.
30MIN
60MIN
90MIN
To activate the timer
5 Press [˚PLAY/REC] to turn on your desired timer.
120MIN
OFF
Sleep timer indicator
To cancel
Press [SLEEP] to select “OFF”.
Changing the remaining time
Press [SLEEP] to show the remaining time, and press
[SLEEP] again to select your desired time.
Note
• The play and sleep timer or the record and sleep timer can be used
together.
• The sleep timer always has priority. Be sure not to overlap timer
settings.
˚ REC
no display (off)
6
Press [y] to turn off the unit.
The unit must be off for the timers to operate.
To enjoy the desired source after the timer setting is
completed.
The volume level (for play timer) and music source are stored
in the timer memory and the timer will start in these preset
conditions. However, the disc numbers do not get stored in
the timer memory.
1. After step 5, start playing the desired source.
2. Reset the disc numbers if you have changed any of them,
confirm that a disc or cassette is inserted, then press [y]
to put the unit on standby.
RQTV0102
Note
The clock may lose or gain minutes over a period of time. Readjust
as necessary.
11
RQTV0102_4B_n.indd 11
3/5/07 2:56:51 PM
Timer (Continued)
Sound adjustment
Other basic operations
To
Action
change the settings
Repeat steps 1 to 4 and 6 on page 11.
change the source
or volume
1) Press [˚PLAY/REC] to clear the timer
indicator from the display.
2) Make changes to the source or volume.
3) Perform steps 5 and 6 on page 11.
check the settings
(when the unit is on
or in standby mode)
Press [CLOCK/TIMER] repeatedly to
select ˚PLAY or ˚REC.
cancel
Press [˚PLAY/REC] to clear the timer
indicators from the display.
Note
• The play timer and record timer cannot be used together.
• The play timer will start at the preset time, with the volume
increasing gradually to the preset level.
• The record timer will start 30 seconds before the set time with the
volume muted.
• The timer comes on at the set time every day if the timer is on.
• The unit must be in the standby mode for the timer to function.
• If you turn the unit off and on again while a timer is functioning, the
finish time setting will not be activated.
• If MUSIC PORT is selected as the source when the timer comes on,
the system turns on and engages MUSIC PORT as the source. If
you wish to playback or record from the portable audio equipment,
activate the equipment’s play mode and increase the volume. (See
the portable audio equipment’s instruction manual.)
Selecting sound effects
You can change the sound effect by selecting Preset EQ or
adjusting the bass or treble effect.
Preset EQ
Press [PRESET EQ] repeatedly to select your desired
setting.
HEAVY → CLEAR → SOFT → VOCAL → EQ-OFF
Setting
HEAVY
CLEAR
SOFT
VOCAL
EQ-OFF
Effect
Adds punch to rock
Clarifies higher frequencies
For background music
Adds gloss to vocal
No effect
Bass or treble
Enable you to enjoy the lower or higher pitch sound.
1
2
Press [BASS] or [TREBLE] to select your desired
setting.
Setting
Effect
BASS
For lower pitch sound
TREBLE
For higher pitch sound
Press [5] or [∞] to adjust the level.
OR
To adjust bass or treble using the main unit.
RQTV0102
Turn [BASS] or [TREBLE] clockwise to increase the
level.
Turn [BASS] or [TREBLE] counter-clockwise to decrease
the level.
Note
The tone level can be varied within -3 to +3.
12
RQTV0102_4B_n.indd 12
3/5/07 2:56:54 PM
External unit
Enjoying surround sound
Enable you to add natural width and depth to the stereo
sound.
To activate
Press [SURROUND] to display “
” indicator.
To cancel
” indicator.
Press [SURROUND] again to clear “
The buttons described for “External unit” are mainly for
the main unit unless indicated otherwise.
Connecting to a portable audio equipment
This feature enables you to enjoy music from portable audio
equipment.
-53)#0
Note
• Surround sound is less discernible when listening through
headphones.
• If interference in FM stereo reception increases, cancel the
surround sound effect.
English
MUSIC
PORT
jack
Enhancing the bass
Enable you to enjoy the powerful bass effect.
Press [H.BASS] repeatedly to select your desired
setting.
LEVEL 1 → LEVEL 2 → OFF
Audio cord (not included)
Note
The actual effect depends on the disc.
Re-master – Enjoying more natural sound
Discs recorded at 32 kHz, 44.1 kHz or 48 kHz
This feature reproduces the frequencies lost during recording
to give you a sound closer to the original.
Press [RE-MASTER] during play to select “RE-MASTER
ON”.
Each time you press the button:
RE-MASTER ON ↔ RE-MASTER OFF
Note
You cannot change RE-MASTER during recording.
English
Portable audio equipment
(not included)
MP3
Playing from portable audio equipment
Switch off the equalizer function (if there is any) of the
portable audio equipment before you plug into the MUSIC
PORT jack. Otherwise, sound from the speaker may be
distorted.
the audio cord into the MUSIC PORT jack and
1 Plug
press [MUSIC P.].
the portable audio equipment. (See the portable
2 Play
audio equipment’s instruction manual.)
Recording from portable audio equipment
1
2
3
4
Insert the cassette to be recorded.
Press [MUSIC P.].
Play the portable audio equipment.
Press [¶ REC¥8] to start recording.
RQTV0102
Note
• All peripheral components and cables are sold separately.
• For other recording operations, refer to page 9, “Other basic
operations”.
13
RQTV0102_4B_n.indd 13
3/5/07 2:56:55 PM
Troubleshooting guide
Before requesting service, make the below checks. If you can’t fix the system as described below, or if something not listed
here occurs, refer to the enclosed directory to locate an Authorized Service Center convenient to you or contact your dealer.
Common problems
No sound.
Turn the volume up.
The speaker cables may not be connected properly. Turn the unit off, check and correct the
connections and turn the unit on (refer to page 4).
Sound is unfixed, reversed or comes
from one speaker only.
Check the speaker connections (refer to page 4).
Humming heard during play.
An AC mains lead or fluorescent light is near the cables. Keep other appliances and cords
away from this unit’s cables.
“ERROR” is displayed.
Incorrect operation performed. Read the instructions and try again.
“– –:– –” appears on the display.
You plugged the AC mains lead in for the first time or there was a power failure recently.
Set the time (refer to page 11).
“F61” is displayed.
Check and correct the speaker cables connections (refer to page 4). Unplug and plug in the
AC mains lead, then turn on the unit.
If this does not fix the problem, there is a power supply problem. Consult the dealer.
Listening to the radio
Noise is heard.
The stereo indicator flickers or doesn’t
light.
Sound is distorted.
Use an outdoor antenna (refer to page 5).
A beat sound is heard.
Turn the TV off or separate it from the unit.
A low hum is heard during AM
broadcast.
Separate the antenna from other cables and cords.
When there is a television set nearby
The picture on the TV
disappears or stripes appear
on the screen.
The location and direction of the antenna are incorrect. If you are using an indoor antenna,
change to an outdoor antenna (refer to page 5).
The TV antenna wire is too close to the unit. Separate the antenna wire of the TV set from
the unit.
Using the cassette deck
Recording is not possible.
If the erasure prevention tabs have been removed, cover the holes with adhesive tape (refer
to page 9).
Playing discs
The display is wrong or play
won’t start.
The disc may be upside down (refer to page 3).
Wipe the disc.
Replace the disc if it is scratched, warped, or non-standard.
Condensation may have formed inside the unit due to a sudden change in temperature. Wait
about an hour for it to clear and try again.
The total number of tracks displayed
differs each time the same disc is
inserted.
Unusual sound is heard.
The disc may be scratched, or its data may be defective. Replace the disc.
CD-RW cannot be read.
The disc was incompletely formatted. Use the recording equipment to fully format the disc
before recording.
“VBR–” is displayed instead of the
remaining play time.
The unit cannot display the remaining play time for variable bit rate (VBR) tracks.
“TAKE OUT/DISC” appears on the
display.
There is a problem with the disc mechanism. (A power failure may have occurred.)
The tray will open automatically. Remove the disc from the tray, and after ensuring there is
no disc in the tray, close it. The unit will make the disc changing noises for a few moments
and then it should operate normally.
The remote control
Check that the batteries are inserted correctly (refer to page 5).
Replace the batteries if they are worn.
RQTV0102
Remote control doesn’t work.
14
RQTV0102_4B_n.indd 14
3/5/07 2:56:56 PM
Specifications
Frequency range
87.50 MHz to 108.00 MHz (50 kHz steps)
Sensitivity
0.3 µV (IHF)
0.2 µV
S/N 26 dB
Antenna terminals
75 Ω (unbalanced)
Preset station
FM 15 stations
AM 15 stations
AM TUNER SECTION
Frequency range
522 kHz to 1629 kHz (9 kHz steps)
520 kHz to 1630 kHz (10 kHz steps)
Sensitivity
For United Kingdom and
Continental Europe
S/N 20 dB (at 999 kHz)
900 µV/m
For Australia and N.Z.
S/N 20 dB (at 1000 kHz)
900 µV/m
CASSETTE DECK SECTION
Track system
4-track, 2-channel
Heads
Record/playback Solid permalloy head
Erasure
Double gap ferrite head
Motor
DC servo motor
Recording system
AC bias 100 kHz
Erase system
AC erase 100 kHz
Tape speed
4.8 cm/s
Overall frequency response (+3, –6 dB at
DECK OUT)
NORMAL
35 Hz to 14 kHz
S/N RATIO
54 dB (A weighted)
Wow and flutter
0.08 % (WRMS)
Fast-forward and rewind time
Approx. 120 seconds with C-60 cassette tape
CD SECTION
Disc played [8 cm or 12 cm]
(1) CD-Audio (CD-DA)
SPEAKER SECTION SC-PM53
Type
2 way, 2 speaker system
Speaker(s)
Woofer
10 cm cone type (6 Ω)
Tweeter
6 cm cone type (6 Ω)
Impedance
6Ω
Input power (IEC)
For United Kingdom and
Continental Europe
50 W (Max)
For Australia and N.Z.
HIGH
90 W (Max)
LOW
90 W (Max)
Output sound pressure 80 dB/W (1.0 m)
Crossover frequency
For United Kingdom and
Continental Europe
3.5 kHz
For Australia and N.Z.
2.2 kHz
Frequency range
For United Kingdom and
Continental Europe
55 Hz to 32 kHz (-16 dB)
78 Hz to 28 kHz (-10 dB)
For Australia and N.Z.
45 Hz to 35 kHz (-16 dB)
50 Hz to 31 kHz (-10 dB)
Dimensions (W x H x D)
144 mm x 249 mm x 200 mm
Mass
1.9 kg
SPEAKER SECTION SC-PM54
Type
3 way, 3 speaker system
Speaker(s)
Woofer
10 cm cone type (6 Ω)
Tweeter
6 cm cone type (6 Ω)
Super Tweeter
2.5 cm piezo type
Impedance
6Ω
Maintenance
If the surfaces are dirty
To clean this unit, wipe with a soft, dry cloth.
• Never use alcohol, paint thinner or benzine to clean this
unit.
• Before using chemically treated cloth, read the instructions
that came with the cloth carefully.
For a cleaner, crisper sound
Clean the heads regularly to assure good quality playback
and recording.
Use a cleaning tape (not included).
RQTV0102_4B_n.indd 15
Input power
For Continental Europe
50 W (Max)
For Australia and N.Z.
HIGH
90 W (Max)
LOW
90 W (Max)
Output sound pressure
For Continental Europe
78 dB/W (1.0 m)
For Australia and N.Z.
80 dB/W (1.0 m)
Crossover frequency
For Continental Europe
1.8 kHz
2.2 kHz
For Australia and N.Z.
Frequency range
For Continental Europe
43 Hz to 19 kHz (-16 dB)
48 Hz to 13.5 kHz (-10 dB)
For Australia and N.Z.
45 Hz to 35 kHz (-16 dB)
50 Hz to 31 kHz (-10 dB)
Dimensions (W x H x D)
144 mm x 249 mm x 200 mm
Mass
2.0 kg
English
FM TUNER SECTION
(2) CD-R/RW (CD-DA, MP3 formatted
disc)
(3) MP3
Sampling frequency
CD
44.1 kHz
MP3
32 kHz, 44.1 kHz, 48 kHz
Bit rate
MP3
32 kbps to 384 kbps
Decoding
16/20/24 bit linear
Pick up
Wavelength
785 nm
Beam source
Semiconductor laser
Laser power
CLASS 1
(For Norge)
Bølgelengde
785 nm
Laserstyrke
Ingen farlig stråling sendes ut
Audio output (Disc)
Number of channels
2-Channel
Frequency response
20 Hz to 20 kHz (+1dB, -2 dB)
Wow and flutter
Below measurable limit
Digital filter
8 fs
D/A converter
MASH (1 bit DAC)
GENERAL
Power supply
For Continental Europe
AC 230V, 50 Hz
For United Kingdom,
Australia and N.Z.
AC 230 to 240 V, 50 Hz
Power consumption
For United Kingdom and
Continental Europe
125 W
156 W
For Australia and N.Z.
Dimensions (W x H x D)
175 mm x 249 mm x 355 mm
Mass
For United Kingdom and
Continental Europe
5.4 kg
5.5 kg
For Australia and N.Z.
Operating temperature range
+5°C to +35°C
Operating humidity range
5% to 90% RH (no condensation)
English
RMS OUTPUT POWER both channel
driven
10% total harmonic distortion
For United Kingdom and
Continental Europe
1 kHz
50 W per channel (6 Ω)
For Australia and N.Z.
1 kHz
(Low channel) 45 W per channel (6 Ω)
8 kHz
(High channel) 45 W per channel (6 Ω)
Total Bi-Amp power 90 W per channel
Input Impedance
Music port
250 mV 12kΩ
Output Impedance
Headphone
16 Ω to 32 Ω
Phone jack
Terminal
Stereo, 3.5 mm
Music port input jack
Terminal
Stereo, 3.5 mm
Power consumption in standby mode
For United Kingdom and
Continental Europe
0.6 W
0.7 W
For Australia and N.Z.
Note
1. Specifications are subject to change
without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by
the digital spectrum analyzer.
The
labels
3. For Australia and N.Z.
“HIGH” and “LOW” on the rear or the
speakers refer to High frequency and Low
frequency.
When moving the unit
1
2
3
Remove all discs.
Press [y/I] to turn the unit off.
Disconnect the AC mains lead.
RQTV0102
AMPLIFIER SECTION
15
3/5/07 2:56:56 PM
CAUTION!
VAROITUS!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
• ÄLÄ ASENNA TAI LAITA TÄTÄ LAITETTA
KABINETTITYYPPISEEN
KIRJAKAAPPIIN
TAI
MUUHUN SULJETTUUN TILAAN, JOTTA TUULETUS
ONNISTUISI. VARMISTA, ETTÄ VERHO TAI MIKÄÄN
MUU MATERIAALI EI HUONONNA TUULETUSTA,
JOTTA
VÄLTETTÄISIIN
YLIKUUMENEMISESTA
JOHTUVA SÄHKÖISKU- TAI TULIPALOVAARA.
• ÄLÄ
PEITÄ
LAITTEEN
TUULETUSAUKKOJA
SANOMALEHDELLÄ, PÖYTÄLIINALLA, VERHOLLA
TAI MUULLA VASTAAVALLA ESINEELLÄ.
• ÄLÄ ASETA PALAVAA KYNTTILÄÄ TAI MUUTA
AVOTULEN LÄHDETTÄ LAITTEEN PÄÄLLE.
• HÄVITÄ
PARISTOT
LUONTOA
VAHINGOITTAMATTOMALLA TAVALLA.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
PRODUCT DAMAGE,
• DO NOT EXPOSE THIS APPARATUS TO RAIN,
MOISTURE, DRIPPING OR SPLASHING AND THAT
NO OBJECTS FILLED WITH LIQUIDS, SUCH AS
VASES, SHALL BE PLACED ON THE APPARATUS.
• USE ONLY THE RECOMMENDED ACCESSORIES.
• DO NOT REMOVE THE COVER (OR BACK); THERE
ARE NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
NORSK
CAUTION!
• DO NOT INSTALL OR PLACE THIS UNIT IN A
BOOKCASE, BUILT-IN CABINET OR IN ANOTHER
CONFINED SPACE. ENSURE THE UNIT IS WELL
VENTILATED. TO PREVENT RISK OF ELECTRIC
SHOCK OR FIRE HAZARD DUE TO OVERHEATING,
ENSURE THAT CURTAINS AND ANY OTHER
MATERIALS DO NOT OBSTRUCT THE VENTILATION
VENTS.
• DO NOT OBSTRUCT THE UNIT’S VENTILATION
OPENINGS WITH NEWSPAPERS, TABLECLOTHS,
CURTAINS, AND SIMILAR ITEMS.
• DO NOT PLACE SOURCES OF NAKED FLAMES,
SUCH AS LIGHTED CANDLES, ON THE UNIT.
• DISPOSE OF BATTERIES IN AN ENVIRONMENTALLY
FRIENDLY MANNER.
The socket outlet shall be installed near the equipment
and easily accessible.
The mains plug of the power supply cord shall remain
readily operable.
To completely disconnect this apparatus from the AC
Mains, disconnect the power supply cord plug from AC
receptacle.
THIS UNIT IS INTENDED FOR USE IN MODERATE
CLIMATES.
SUOMI
VAROITUS!
LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ
KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA
ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.
VAROITUS:
VÄHENNÄ
TULIPALON,
SÄHKÖISKUN
TAI
LAITTEISTON VAHINGOITTUMISEN VAARAA
• TÄTÄ LAITETTA EI SAA ALTISTAA SATEELLE,
KOSTEUDELLE, ROISKEILLE TAI TIPPUVILLE
NESTEILLE. LAITTEEN PÄÄLLE EI SAA MYÖSKÄÄN
ASETTAA
MITÄÄN
NESTEELLÄ TÄYTETTYÄ
ESINETTÄ, KUTEN MALJAKKOA.
• KÄYTÄ VAIN SUOSITELTUJA LISÄVARUSTEITA.
• ÄLÄ IRROTA KANTTA (TAI TAUSTAA). SISÄLLÄ
EI OLE KÄYTTÄJÄN HUOLLETTAVISSA OLEVIA
OSIA.
HUOLLON
SAA
SUORITTAA
VAIN
AMMATTITAITOINEN HENKILÖKUNTA.
TÄMÄ LAITE ON TARKOITETTU
LEUDOSSA ILMASTOSSA.
Pistorasia tulee asentaa laitteen lähelle helppopääsyiseen
paikkaan.
Verkkojohdon pistokkeen on oltava aina helposti käytettävissä.
Tämä laite voidaan kytkeä kokonaan irti verkkovirrasta
irrottamalla verkkojohdon pistoke pistorasiasta.
KÄYTETTÄVÄKSI
Matsushita Electric Industrial Co., Ltd.
Web Site: http://panasonic.net
ADVARSEL!
DETTE PRODUKTET ANVENDER EN LASER.
BETJENING AV KONTROLLER, JUSTERINGER ELLER
ANDRE INNGREP ENN DE SOM ER BESKREVET
I DENNE BRUKSANVISNING, KAN FØRE TIL FARLIG
BESTRÅLING.
DEKSLER MÅ IKKE ÅPNES, OG FORSØK ALDRI Å REPARERE APPARATET PÅ EGENHÅND. ALT SERVICE
OG REPARASJONSARBEID MÅ UTFØRES AV
KVALIFISERT PERSONELL.
ADVARSEL:
FØLG NEDENSTÅENDE INSTRUKSER FOR Å
REDUSERE RISIKOEN FOR BRANN, ELEKTRISK STØT
OG SKADE PÅ PRODUKTET:
• DETTE APPARATET MÅ IKKE UTSETTES FOR REGN,
FUKTIGHET, DRYPP ELLER SPRUT, OG INGEN
VÆSKEFYLTE GJENSTANDER, SOM F.EKS. VASER,
MÅ PLASSERES PÅ APPARATET.
• BRUK KUN ANBEFALT TILBEHØR.
• IKKE FJERN DEKSELET (ELLER BAKSIDEN);
APPARATET INNEHOLDER INGEN DELER SOM
KAN SKIFTES ELLER REPARERES AV BRUKEREN.
OVERLAT TIL KVALIFISERTE SERVICETEKNIKERE Å
UTFØRE SERVICE.
ADVARSEL!
• APPARATET MÅ IKKE PLASSERES I EN BOKHYLLE,
ET INNEBYGGET KABINETT ELLER ET ANNET
LUKKET STED HVOR VENTILASJONSFORHOLDENE
ER
UTILSTREKKELIGE.
SØRG
FOR
AT
GARDINER ELLER LIGNENDE IKKE FORVERRER
VENTILASJONSFORHOLDENE, SÅ RISIKO FOR
ELEKTRISK SJOKK ELLER BRANN FORÅRSAKET
AV OVERHETING UNNGÅS.
• APPARATETS VENTILASJONSÅPNINGER MÅ IKKE
DEKKES TIL MED AVISER, BORDDUKER, GARDINER
OG LIGNENDE.
• PLASSER IKKE ÅPEN ILD, SLIK SOM LEVENDE LYS,
OPPÅ APPARATET.
• BRUKTE BATTERIER MÅ KASSERES UTEN FARE
FOR MILJØET.
DETTE APPARATET ER BEREGNET TIL BRUK UNDER
MODERATE KLIMAFORHOLD.
Strømuttaket må befinne seg i nærheten av utstyret og
være lett tilgjengelig.
Støpslet på strømkabelen må være klart til bruk.
Når dette apparatet skal kobles helt fra strømnettet (AC),
må støpslet på strømkabelen trekkes ut av stikkontakten.
En
RQTV0102-4B
L0106CH4037
RQTV0102_4B_n.indd 16
3/5/07 3:12:11 PM

advertisement

Key Features

  • Plays CDs, MP3s, and cassettes
  • Recordings from external sources on cassette tape are possible
  • Timer-based music playback
  • Option to connect external devices

Related manuals

Frequently Answers and Questions

Can I play MP3 files on this player?
Yes, you can play MP3 files on this player.
Can I record music from the radio onto a cassette tape?
Yes, you can record music from the radio onto a cassette tape using this player.
Can I connect my phone to this player?
Yes, you can connect external devices to this player.

advertisement