GEM-P801 Programming Instructions
GEM-P801 Programming Instructions
®
DEFAULTING THE PANEL
Scroll Key
Note: These Programming Instruction are intended to be used in conjunction with WI1089.
Please refer to WI1089 for additional information, instructions and definitions.
Use this key to scroll through data
that has been entered in
Programming Blocks.
- KEYPAD KEY DEFINITION
DEALER PROGRAM MODE
NOTE:
After 15 minutes of keypad
inactivity the keypad will emit a
steady tone indicating the
panel has been left in Dealer
Program Mode. Enter Dealer
Code to exit or press the C
key to return to Dealer
Program mode.
Blank Key
I
H
ED
ARM
1
2
3
4
5
B 4 5 6
Press this key before
entering a Programming
Block Number.
6
7
8
TUS
STA
A 1 2 3
Set Key
Press this key to disable all
features within a LED type
Programming Block or to blank out
digits in a Direct Entry type
Programming Block.
GEMINI
C 7 8 9
J
E
Hexadecimal Data Entry
To Enter a hexadecimal digit enter the
following:
F
0 G
A=
B=
C=
COMPUTERIZED SECURITY SYSTEM
G1
G2
G3
Dealer Code
Entering Dealer Program Mode
Enter
J
A8
(4) (5) (6) (7)
NOTE:
Entering Dealer Program Mode is not permitted while the panel is
Armed, Reporting, or the Bell Output is on. To Enter Dealer
Mode while the Bell is ON or the panel is Reporting or Armed;
power up the panel and enter Dealer Mode within the first 3
minutes. Pressing the C key clears the 3 minute timer.
Exiting Dealer Program Mode
H
D=
E=
F=
G4
G5
G6
ARMED
ON
STATUS
OFF
TROUBLE
FLASHING
ARMED
FLASHING
STATUS
FLASHING
TROUBLE
FLASHING
1. Remove power from the panel.
2. Remove all wiring from terminal 19
(PGM) and terminal 3.
3. Connect terminal 19 (PGM) to
terminal 3.
4. Apply power to the GEM-P801
control panel.
5. After a few seconds the ARMED,
READY and HSYSTEM TROUBLE
LEDs will flash.
6. The keypad will beep 3 times
indicating the panel default values
have been loaded.
7. Remove wiring between terminal 19
(PGM) and terminal 3.
8. Re-install original wiring for terminal
19 (PGM) and terminal 3.
Note: Any programming in Dealer
Options 1 [96] and Dealer Options 2
[97] will not be defaulted. If Dealer
Code
Lockout
has
been
programmed the panel will not
default the Dealer Code. The Event
Log will be erased when the panel is
defaulted.
Indicates the panel is in Dealer
Program Mode. The panel is
ready for a programming block to
be entered.
Default Dealer Code shown in parentheses
Dealer Code
J
Enter C A 8
(4) (5) (6) (7)
H
Indicates the panel is Ready to
exit Dealer Program Mode.
Enter the Dealer Code to exit.
WI1090A 12/01
1
Types of Programming Blocks
LED Programming Block
Enable features by pressing the key that corresponds to the associated feature; the LED will turn ON. To disable a feature press the key
again; the LED will turn OFF. To disable all features within a LED Type Programming Block press the F key; all LEDs will turn OFF.
1
LED Programming Block Example
Program zones 2 and 3 as Follower Zones.
02 Exit/Entry Follower
OFF
1. Enter Programming Block 02, by pressing
C (Beep), then 02 (Beep).
2. Press the 2 key to select zone 2.
3. Press the 3 key to select zone 3.
Zone 2 and Zone 3
LED Type
are
ON
Programming LEDs
indicating
that
Block
zones 2 and 3 have
been programmed
as follower zones.
Default
OFF
OFF
OFF
OFF
OFF
OFF
OFF
²
²
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Zone 7
Zone 8
Direct Entry Programming Block
Enter data directly. For hexadecimal entries of A-F, use the G key + 1 through 6 keys, respectively. Use the
F
1
key to blank out digits in Direct Entry type programming blocks. Default values are shown in parentheses.
Direct Entry Programming Example 1
Program the panel for a 60 second Exit Delay.
10 Exit Delay
0
1. Press C (Beep) 10 (Beep).
2. Press 060.
6
0 Exit Delay, seconds
(0) (4) (5) Maximum Entry 255
9
44 Dialing Prefix
2
E
Direct Entry Programming Example 2
(Hexadecimal data entry)
Program Telephone Prefix Number with a 9E.
1.
2.
3.
4.
2
Direct Entry
Type
Programming
Blocks
Press C (Beep) 44 (Beep).
Press 9
Press G
Press 5
H
ARMED
OFF
STATUS
FLASHING
TROUBLE
FLASHING
Indicates the panel is in Dealer
Program Mode; the next digit entered
will be interpreted as a Hexadecimal
digit. Valid entries are 1-6 (A-F).
GEMINI
I
H
S TA
ED
ARM
T US
2
3
Viewing Data in Programming
To view data within a programming block, press C and enter the Program Block Number to view the 1st digit of data. Press the E key to view the 2nd
digit and continue pressing E until all digits within the Block have been viewed. Data will be displayed in the binary format shown in the table below:
Value
Data Displayed
Value
Data Displayed
0/Blank
8
4
1
9
1
2
2
3
1 2
4
5
6
7
4
1 2
4
(800) 645-9440
C
3
D
2 3
E
2 3 4
1 2 3
F
1 2 3 4
3 4
1
Zone # Bit Value
1
1
2
2
3
4
4
8
3 4
Example: Viewing the Dialing Prefix
A Dialing Prefix of 9E has been programmed at Programming Block Number
44 (outside access number). Follow the steps below to view the data:
1
In the following Programming
Blocks, data that has been entered
as a ‘0’ will be displayed as an ‘A’:
Subscriber ID Numbers, Phone
Numbers, Pager Leading and
Trailing digits and Report Codes.
2
4
3
1
NOTE:
For Technical Assistance,
Contact the NAPCO Toll
Free Helpline 1
*A/0
B
*
Press C44 to enter Programming Block 44.
9
E
GEMINI
H
ED
ARM
Press the E key to view the 2nd digit.
The
Following
Programming Options
are not permitted for UL
installations: [05], [06],
[23-2], [26-3] and [26-4].
44 Dialing Prefix
The 1st digit of Programming Block 44 is displayed.
2
NOTE:
T
STA
1
4
US
DATA = 9
GEMINI
H
ED
ARM
T
STA
2
3
4
The UL symbol by a
programming
Block
indicates
the
programming option is
not permitted for UL
installations.
NOTE:
For information about
programming
blocks
refer to GEM-P801
Installation
Manual
WI1089.
US
DATA = E
3
Zone Features
03 Auto Bypass Reentry Zones
00 Exit/Entry Zones
Default
Default
UL
06 Disable EOL Resistor
09 Selective Bypass
Default
Default
ON
Zone 1
OFF
Zone 1
OFF
Zone 1
ON
Zone 1
OFF
Zone 2
OFF
Zone 2
OFF
Zone 2
ON
Zone 2
OFF
Zone 3
OFF
Zone 3
OFF
Zone 3
ON
Zone 3
OFF
OFF
OFF
Zone 4
Zone 5
ON
OFF
Zone 4
Zone 5
OFF
OFF
Zone 4
Zone 5
ON
Zone 4
Zone 5
OFF
Zone 6
OFF
Zone 6
OFF
Zone 6
ON
Zone 6
OFF
Zone 7
OFF
Zone 7
ON
Zone 7
OFF
Zone 8
OFF
Zone 8
ON
Zone 8
04 24 Hour Protection Zones
01 Home/Away with Delay Zones
Default
Default
OFF
Zone 1
OFF
OFF
Zone 2
OFF
OFF
Zone 3
OFF
OFF
OFF
OFF
OFF
07 Burg (Steady) Output
Default
Zone 1
ON
Zone 1
Zone 2
ON
Zone 2
OFF
Zone 3
ON
Zone 3
Zone 4
Zone 5
OFF
Zone 4
Zone 5
ON
OFF
ON
Zone 4
Zone 5
Zone 6
OFF
Zone 6
ON
Zone 6
Zone 7
OFF
Zone 7
ON
Zone 7
Zone 8
OFF
Zone 8
ON
Zone 8
02 Exit/Entry Follower Zones
Default
UL
05 40 ms Loop Response Zones
Default
08 Programmable Output (PGM)
Default
OFF
Zone 1
OFF
Zone 1
ON
Zone 1
OFF
Zone 2
OFF
Zone 2
ON
Zone 2
OFF
Zone 3
OFF
Zone 3
ON
Zone 3
OFF
Zone 4
Zone 5
OFF
Zone 4
Zone 5
ON
Zone 4
Zone 5
OFF
OFF
OFF
ON
OFF
Zone 6
ON
Zone 6
OFF
Zone 7
ON
Zone 7
OFF
Zone 8
ON
Zone 8
Zone 6
System Times
10 Exit Delay
Exit Delay, seconds
(0) (4) (5) Maximum Entry 255
11 Entry Delay
Entry Delay, seconds
(0) (3) (0) Maximum Entry 255
12 Burg (Steady) Output Time-out
Bell Time-out, minutes
(0) (0) (5) Maximum Entry 255
13 Fire (Pulsed) Output Time-out
Bell Time-out, minutes
(0) (0) (0) Maximum Entry 255
14 Test Timer Interval
Test Timer/Line Test, days
(0) (0) (0) Maximum Entry 255
4
System Times
15 Line Cut Time-to-Fail (Disabled = 000)
System Features
20 Keypad Features 1
(0) (0) (0) Enable Feature-Valid Entries 10-255
Supervisory Timer, hours
OFF
Zn 1 LED ON = Fire
OFF
Zn 2 LED ON = *Keypad AUX (8G )
OFF
Zn 2 LED ON = AUX
ON
Zn 3 LED ON = *Keypad Panic (9G )
OFF
Zn 3 LED ON = Panic
OFF
Zn 4 LED ON = Test Timer
25 Programmable Output (PGM) Features 3
Default
17 Wireless Smoke Supervisory Timer
Smoke Supervisory Timer, hours
Maximum Entry 8
Zn 1 LED ON = *Keypad Fire (7G )
21 Keypad Features 2
*See Note 4
(8)
Default
OFF
OFF
Zn 4 LED ON = *Ambush (8th User Code)
*See Note 1
16 Wireless Supervisory Timer
(1) (2) Maximum Entry 26
24 Programmable Output (PGM) Features 2
Default
Line Cut Time-to-Fail, seconds
Default
ON
Zn 1 LED ON = Audible panic
OFF
Zn 1 LED ON = AC Fail
OFF
Zn 2 LED ON = Exit/Entry with Urgency
OFF
Zn 2 LED ON = Low Battery
ON
Zn 3 LED ON = Display Bypass (ARMED)
OFF
Zn 3 LED ON = *Trouble
OFF
Zn 4 LED ON = Disable Code Entry Beeps
OFF
Zn 4 LED ON = Armed
*See Note 3
22 Miscellaneous Features 1
26 Miscellaneous Features 2
Default
18 Test Timer Offset
Test Timer,
Timer Offset,
hours hours
(1)
(2)
Maximum Entry 23
29 Chime Time
Valid Entries 2-9
Zn 1 LED ON = Abort Delay
OFF
Zn 1 LED ON = Momentary Keyswitch
ON
Zn 2 LED ON = Easy Arm/Easy Exit
OFF
Zn 2 LED ON = Reserved
ON
Zn 3 LED ON = Swinger Shutdown
UL
OFF
Zn 3 LED ON = Inhibit Fail to Communicate
OFF
Zn 4 LED ON = Bell on Line Cut (Armed)
UL
OFF
Zn 4 LED ON = Inhibit Low Battery Display
23 Programmable Output (PGM) Features 1
Zn 1 LED ON = Audio Verification
OFF
Zn 1 LED ON = Keyswitch Polarity
OFF
Zn 2 LED ON = *Access Output (A3)
OFF
Zn 2 LED ON = Reserved
OFF
Zn 3 LED ON = *Follow Keypad Sounder
OFF
Zn 3 LED ON = Reserved
OFF
Zn 4 LED ON = Reserved
OFF
UL
27 Miscellaneous Features 3
Default
Default
Chime Time, 1/4 seconds
(4)
Default
OFF
OFF
Zn 4 LED ON = Keyfob/Keyswitch Bell
*See Note 2
NOTE 1:
NOTE 3:
Additional programming required for reporting, see Blocks [36]&[56].
UL Installations: If Keypad Fire [20-1] is enabled, the keypad must be mounted
within (3) three feet from the Control Panel.
Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Receiver JAM, Transmitter Low Battery, Transmitter Supervisory Failure,
Wireless Smoke Low Battery and Wireless Smoke Supervisory Failure.
NOTE 2:
Cannot be programmed with any other Programmable Output (PGM) Feature.
NOTE 4:
UL Installations: Block 16, Wireless Supervisory Timer must be set 10 hours.
5
Telephone Number 1 Programming
30 Subscriber ID Number
37 System Reporting, Telco 1
34 Zone Report, Telco 1
Default
31 Telephone Number 1
A fixed Dial Tone Detection “E” is included by default in the Dialing Prefix
(Block Number 44). If dial tone detection is not desired, Remove the “E” from
Block 44. Program a “D” if a 4 second delay is required.
Default
ON
Zone 1
OFF
Zn 1 LED ON = AC Fail Report (15 min. report delay)
ON
Zone 2
ON
Zn 2 LED ON = Low Battery Report
ON
Zone 3
OFF
Zn 3 LED ON = *Trouble Report
ON
ON
Zone 4
Zone 5
ON
Zn 4 LED ON = Fire Report
*See Note 2
ON
Zone 6
ON
Zone 7
ON
Zone 8
38 System Restore Report, Telco 1
Default
35 Zone Restore Report, Telco 1
32 Receiver Format
OFF
Zn 1 LED ON = AC Restore Report
OFF
Zn 2 LED ON = Battery Restore Report
OFF
Zn 3 LED ON = Trbl Restore Report
OFF
Zn 4 LED ON = Fire Restore Report
Default
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
Disabled
Ademco Slow
Radionics Slow
Silent Knight Fast
Universal High Speed
Reserved
Ademco Point ID
Pager
(4)
OFF
Zone 1
OFF
Zone 2
OFF
Zone 3
OFF
Zn 1 LED ON = User 1 Reporting
OFF
OFF
OFF
Zone 4
Zone 5
Zn 2 LED ON = User 2 Reporting
OFF
OFF
Zn 3 LED ON = User 3 Reporting
Zone 6
OFF
OFF
Zone 7
OFF
Zn 4 LED ON = User 4 Reporting
Zn 5 LED ON = User 5 Reporting
OFF
Zone 8
OFF
Zn 6 LED ON = User 6 Reporting
OFF
Zn 7 LED ON = User 7 Reporting
OFF
Zn 8 LED ON = User 8 Reporting
39 Opening Closing Report, Telco 1
Default
33 Receiver Options
Default
6
ON
Zn 1 LED ON = 2300 Hz Handshake/Kissoff
OFF
Zn 2 LED ON = Sumcheck
OFF
Zn 3 LED ON = Single Digit
OFF
Zn 4 LED ON = No Handshake
36 System Reporting, Telco 1
NOTE 1:
Default
OFF
Zn 1 LED ON = *KP Fire
OFF
ON
Zn 2 LED ON = *KP AUX (8G )/Ambush
Zn 3 LED ON = *KP Panic (9G )
OFF
Zn 4 LED ON = Test Timer
(7G )
Requires features to be enabled, see block [20].
NOTE 2:
Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Receiver JAM, Transmitter Low Battery, Transmitter Supervisory Failure,
Wireless Smoke Low Battery, Wireless Smoke Supervisory Failure.
ZONE 3 TX LOW BATTERY
SMOKE 2 LOW BATTERY
“RF TRAN LOW BAT, ZN03”
“RF TRAN LOW BAT, ZN10”
Backup Telephone
Programming
40 Subscriber ID Number (Telco 2)
Pager Programming
44 Dialing Prefix
47
Dialing Prefix for Telco 1, Telco 2
& Telco 3.
Leading Digits
(0)
(0)
(0)
(0)
41 Telephone Number 2
45 Communicator Features 1
Default
NOTE:
ON
Zn 1 LED ON = Communicator Enabled
A fixed Dial Tone Detection “E” is included by default in the Dialing Prefix
(Block Number 44). If dial tone detection is not desired, Remove the “E” from
Block 44. Program a “D” if a 4 second delay is required.
ON
Zn 2 LED ON = DTMF w/ Rotary Back up
OFF
Zn 3 LED ON = DTMF only
OFF
Zn 4 LED ON = Backup to Telco 2
48
42 Receiver Format
[1]
[2]
[3]
[4]
[5]
[6]
[7]
Ademco Slow
Radionics Slow
Silent Knight Fast
Universal High Speed
Reserved
Ademco Point ID
Pager
46 Communicator Features 2
Default
(4)
OFF
Zn 1 LED ON = Reserved
OFF
Zn 2 LED ON = 2:1 Rotary Dialing
OFF
Zn 3 LED ON = Backup if < 4 attempts
ON
Zn 4 LED ON = * Don't Clear Fail to Comm.
*See Note 1
Trailing Digits
*(C) *See Note 2
49 Pager Option
Default
OFF
Zn 1 LED ON = Skip Alarm Data
OFF
Zn 2 LED ON = Reserved
OFF
Zn 3 LED ON = Reserved
OFF
Zn 4 LED ON = Reserved
43 Receiver Options
Default
ON
Zn 1 LED ON = 2300 Hz Handshake/Kissoff
OFF
Zn 2 LED ON = Sumcheck
OFF
Zn 3 LED ON = Single Digit
OFF
Zn 4 LED ON = No Handshake
NOTE 1:
If Don't Clear Fail to Comm. is programmed, only a successful
communication to Central Station will clear a Failure to
Communicate system trouble.
NOTE 2:
C = TouchTone #. This is the typical terminating digit for most
paging systems. Recommended, but may not be required by
paging system. D = 2 second delay.
7
Telephone Number 3 Programming
50 Subscriber ID Number
54 Zone Report, Telco 3
57 System Reporting, Telco 3
Default
51 Telephone Number 3
NOTE:
A fixed Dial Tone Detection “E” is included by default in the Dialing Prefix
(Block Number 44). If dial tone detection is not desired, Remove the “E” from
Block 44. Program a “D” if a 4 second delay is required.
Default
OFF
Zone 1
OFF
Zn 1 LED ON = AC Fail Report (15 min. report delay)
OFF
Zone 2
OFF
Zn 2 LED ON = Low Battery Report
OFF
Zone 3
OFF
Zn 3 LED ON = *Trouble Report
OFF
OFF
Zone 4
Zone 5
OFF
Zn 4 LED ON = Fire Report
*See Note 2
OFF
Zone 6
OFF
Zone 7
OFF
Zone 8
58 System Restore Report, Telco 3
Default
55 Zone Restore Report, Telco 3
Default
52 Receiver Format
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
Disabled
Ademco Slow
Radionics Slow
Silent Knight Fast
Universal High Speed
Reserved
Ademco Point ID
Pager
(4)
OFF
Zone 1
OFF
Zone 2
OFF
Zone 3
OFF
OFF
Zone 4
Zone 5
OFF
Zone 6
OFF
Zone 7
OFF
Zone 8
Default
Zn 1 LED ON = AC Restore Report
OFF
Zn 2 LED ON = Battery Restore Report
OFF
Zn 3 LED ON = Trbl Restore Report
OFF
Zn 4 LED ON = Fire Restore Report
59 Opening Closing Report, Telco 3
Default
56 System Reporting, Telco 3
53 Receiver Options
OFF
Default
OFF
Zn 1 LED ON = *KP Fire
Zn 2 LED ON = *KP AUX (8G )/Ambush
Zn 3 LED ON = *KP Panic (9G )
(7G )
ON
Zn 1 LED ON = 2300 Hz Handshake/Kissoff
OFF
OFF
Zn 2 LED ON = Sumcheck
OFF
OFF
Zn 3 LED ON = Single Digit
OFF
Zn 4 LED ON = No Handshake
Zn 4 LED ON = Test Timer
OFF
*See Note 1
OFF
Zn 1 LED ON = User 1 Reporting
OFF
Zn 2 LED ON = User 2 Reporting
OFF
Zn 3 LED ON = User 3 Reporting
OFF
OFF
Zn 4 LED ON = User 4 Reporting
Zn 5 LED ON = User 5 Reporting
OFF
Zn 6 LED ON = User 6 Reporting
OFF
Zn 7 LED ON = User 7 Reporting
OFF
Zn 8 LED ON = User 8 Reporting
NOTE 1:
Requires features to be enabled, see block [20].
NOTE 2:
Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Receiver JAM, Transmitter Low Battery, Transmitter Supervisory Failure,
Wireless Smoke Low Battery, Wireless Smoke Supervisory Failure.
ZONE 3 TX LOW BATTERY
SMOKE 2 LOW BATTERY
8
“RF TRAN LOW BAT, ZN03”
“RF TRAN LOW BAT, ZN10”
Report Codes
60 Zone Report Codes
Zone 1 Alarm Code
(3)
Zone 2 Alarm Code
(3)
Zone 3 Alarm Code
62 Zone Codes
Zone 1, 2, 3, 4, 5, 6, 7 & 8 Restore Code
NOTE:
The second digit of the
Report Code is the number
of the zone that is reporting.
For example zone 5 report
code (default of 3) would be
35.
(3)
(E)
Zone 1, 2, 3, 4, 5, 6, 7 & 8 Trouble Code
(F)
(3)
Zone 5 Alarm Code
(1)
(3)
(2)
(3)
(2)
(1)
(F)
(F)
(F)
(9)
(3)
Test Timer
Zone 8 Alarm Code
(3)
AC Fail
61 Point ID Report Codes
Zone 3 Alarm Code
(3)
Zone 4 Alarm Code
(3)
Zone 5 Alarm Code
(3)
Zone 6 Alarm Code
(3)
Zone 7 Alarm Code
(3)
Zone 8 Alarm Code
(2)
(F)
1
2
3
4
5
6
7
8
9
A
B
FIRE
PANIC
BURGLARY
HOLDUP
GENERAL ALARM
RESERVED
GAS ALARM
HEAT ALARM
RESERVED
AUXILIARY
24 HOUR ALARM
Note: See page 11 for
complete listing of
Point ID report codes.
(8)
*Trouble
(F)
Enhanced Communicator Features
67 Telephone Number 1
Default
Low Battery
Zone 1 Alarm Code
(3)
(2)
Keypad Panic (9G)
Zone 7 Alarm Code
(3)
(1)
Keypad AUX (8G)
Zone 6 Alarm Code
Zone 2 Alarm Code
66 Ambush Report Code
Keypad Fire (7G)
(3)
(3)
(C) Closing Code
(B) Opening Code
63 System Report Codes
Zone 4 Alarm Code
65 Opening and Closing Code
(1)
OFF
Zn 1 LED ON = Opening after Alarm (Cancel Code)
OFF
Zn 2 LED ON = Conditional Closing
OFF
Zn 3 LED ON = Reserved
OFF
Zn 4 LED ON = Reserved
Fire
(1)
(1)
*See Note 1
64 System Restore Code
(E)
68 Telephone Number 3
Default
OFF
Zn 1 LED ON = Opening after Alarm (Cancel Code)
OFF
Zn 2 LED ON = Conditional Closing
OFF
Zn 3 LED ON = Reserved
OFF
Zn 4 LED ON = Reserved
NOTE 1:
Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Receiver JAM, Transmitter Low Battery, Transmitter Supervisory Failure,
Wireless Smoke Low Battery and Wireless Smoke Supervisory Failure.
9
Wireless
Transmitters
RF ID #
Point
71 Zone 1
:
72 Zone 2
:
73 Zone 3
:
74 Zone 4
:
75 Zone 5
:
76 Zone 6
:
77 Zone 7
:
78 Zone 8
:
Keyfobs
RF ID #
83 Keyfob 3
84 Keyfob 4
:
82 Keyfob 2
RF ID # XXXXXX:X
Enter the point number to be
associated with the zone. If only
one point of GEM-TRANS2 is
used, enter a 1 in this location.
For GEM-GB, GEM-DT, GEMPIR enter a 1 in this location.
AUX 1 AUX 2
:
:
:
81 Keyfob 1
Programming Example
Enter the RF ID# located on the
Transmitter, Key Fob and
Smoke Detector labels.
AUX 1 & 2
Programming
1
2
3
4
5
6
7
8
Panic
AUX
Bell ON
PGM
Instant
Access on PGM
Full Set System
Interior
Map point 1 of a window door transmitter, with RF ID# 0012B0:0
to Zone 3.
73 Zone 3
0
0
1
2
B
0
:0
1
1. Enter Dealer Mode.
2. Enter C (beeps) 7 3 (beeps)
3. Enter
0012G200
4. Enter
1
(beeps)
Hexadecimal B Entry
Note: If the RF ID# in step 3 is not entered correctly the
keypad will emit a 1 second tone indicating incorrect entry.
Repeat steps 2 - 4 above.
Smoke Detectors
RF ID #
85 Smoke 1
:
86 Smoke 2
:
87 Smoke 3
:
88 Smoke 4
:
Hexadecimal Data Entry
To Enter a hexadecimal digit enter the following:
10
A= G 1
B= G 2
C= G 3
D= G 4
E= G 5
F= G 6
Downloading
90 Callback Telephone Number
Dealer Programming
94 Dealer Code
97 Dealer Options 2
Default
(4) (5) (6) (7)
NOTE:
A fixed Dial Tone Detection “E” is required if callback downloading is to be
utilized. Place the “E” in the first location of Block 90, before the Callback
Telephone Number. Program a “D” if a 4 second delay is required.
95 User 1 Code
(0) (9) Maximum Entry 15
Zn 1 LED ON = * International Dialing Protocol
OFF
Zn 2 LED ON = * Invert Bell Output
OFF
Zn 3 LED ON = System Trouble Auto Reset
OFF
Zn 4 LED ON = User 1 Code-Program only
*See Note 1
(1) (2) (3) (4)
91 Ring Count
OFF
98 Number of Re-Dials
# of communication re-dial attempts
96 Dealer Options 1
Default
OFF
Zn 1 LED ON = Dealer Code Lockout
ON
Zn 2 LED ON = User 1 Code Lockout
OFF
Zn 3 LED ON = UL Household Fire
OFF
Zn 4 LED ON = Fire Trouble on Fire LED
(9)
NOTE 1:
International Features
92 Downloading Features
Default
ON
Zn 1 LED ON = Ring Method
ON
Zn 2 LED ON = Answering Machine override
ON
Zn 3 LED ON = Function 6 (A6)
OFF
Zn 4 LED ON = Signal Strength Test Mode
93 Auto Download ID Number
Zone Alarm Codes
1 Fire
2 Panic
3 Burglary
Point ID Report Codes
System Codes
110-000
Receiver Tamper
145-000
123-00X
130-00X
301-000
302-000
AC Fail
Low Battery
4 Holdup
122-00X
Bell Cut
321-000
5 General Alarm
140-00X
Receiver Jam
333-000
7 Gas Alarm
151-00X
Fire Zone Trouble
373-000
8 Heat Alarm
158-00X
Transmitter Supervisory Fail
381-00X
A Auxiliary
100-00X
Wireless Smoke Sup. Fail
381-00X
B 24 Hour Aux.
150-00X
Poll Fail
382-000
Transmitter Low Battery
384-00X
Keypad Codes
Keypad Fire
110-000
Wireless Smoke Low Battery
384-00X
Keypad Panic
123-000
Conditional Open/Close
400-00X
Keypad Aux Alarm
Keypad Ambush
140-000
121-000
Open/Close
Test Timer
401-00X
602-000
Communication Test
602-000
11
E1
E2
This equipment should be installed in accordance with Chapter 2 of the National Fire
Alarm Code, ANSI/NFPA 72-1996 (National Fire Protection Association
Batterymarch Park, Quincy MA 02269). and local codes. Information describing
proper installation, operation, testing, maintenance, evacuation planning, and repair
service is to be provided with this equipment. UL Listed Energy Cable is required.
GEM-P801 WIRING DIAGRAM
(REFER TO INSTALLATION INSTRUCTIONS WI1089
+ RED
RECHARGEABLE
BATTERY
12 VDC 4AH OR 7AH
BLACK
RECOMMENDED BATTERIES YUASA
NP4-12 AND NP7-12
REPLACE EVERY FIVE YEARS
COLD WATER GROUND CONNECTION
USE ONLY COLD-WATER PIPE OR
BURIED GROUND ROD. USE AT LEAST
#16 AWG WIRE.
RESIDENTIAL BURG (4 HOUR STANDBY)
COMBINED STANDBY = 500 mA
BELL = 2.0 A
RESIDENTIAL FIRE (24 HOUR STANDBY) (2)
COMBINED STANDBY = 120 mA
BELL = 95 mA
DS1
TEL LINE IN USE
1
2
+3
-4
+5
+6
-7
+8
+9
-10 +11 +12 -13
FIRE
PWR
15
BELL
GND
2.2K
ZONE 3 ZONE 4
2.2K
+
+
ZONE 5 ZONE 6
2.2K
ALL OUTPUTS ARE CURRENT LIMITED
2.2K
2.2K EOLR
2.2K EOLR
(SUPERVISED)
RED
Power
Out (+)
Power
In (+)
BLACK
Power
Out (-)
Power
In (-)
BROWN
BROW
(+)
GEM-RECV-XP8
16
+PWR
GEM-P8001 Terminals
FT2200
4-Wire
Fire
Wiring
GEM-RP8
(-)
Programmable
Output
(1) COMBINED STANDBY = KEYPAD CURRENT + AUX POWER
CURRENT + FIRE POWER + PGM CURRENT.
(2) RESIDENTIAL FIRE REQUIRES A 7AH BATTERY.
(3) UNIT INTENDED TO BE MOUNTED VERTICALLY ON WALL.
(4) REFER TO WI1089 FOR COMPATIBLE TWO WIRE SMOKE
DETECTORS. DO NOT MIX DIFFERENT MODELS.
(5) THIS PANEL SHALL BE CHECKED BY A QUALIFIED
TECHNICIAN AT LEAST ONCE EVERY THREE YEARS.
(6) THIS PANEL SUPPORTS ONLY ONE SMOKE DETECTOR IN
ALARM.
(7) USE ONLY ONE BELL IN RESIDENTIAL FIRE APPLICATION.
(8) SYSTEM MUST BE TESTED AT LEAST ONCE A WEEK IN
THE AC/BATTERY MODE AND IN THE BATTERY-ONLY
MODE. (CONTACT CENTRAL STATION PRIOR TO
TESTING) AC MUST BE RESTORED AFTER TEST.
2.2K
19
PGM
LOAD
50 mA MAX.
ZONE 1 ZONE 2
2.2K
18
BLK
+
2.2K
17
GND GREEN
GRN
+
Class 2 Transformer
DO NOT connect
to switched outlet.
16
+PWR
REMOTE BUS
+
2.2K
12
14
AUX POWER OUTPUT 10-12.5 VDC
EARTH
GROUND
FIRE
RED
16 VAC 20 VA
TRANSFORMER
NAPCO TRF12
(OR EQUIVALENT
SEE WI1089).
To RJ31X
(Supervised)
TELCO
JACK
Fire Loop
Fire
Out
Loop In
12 Fire Power
10 Ground
12 Fire Power
13 Fire
WARNING
TO PREVENT RISK
OF ELECTRIC SHOCK
DISCONNECT TELEPHONE
LINES PRIOR TO
SERVICING
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement