TOSHIBA e-STUDIO6550C GD-1270, e-STUDIO306LP GD-1250, GD-1260, e-STUDIO856 GD-1250, GD-1250, e-STUDIO456 GD-1250, GD-1250, e-STUDIO4540C GD-1250, e-STUDIO556SE GD-1250, e-STUDIO556 GD-1250, e-STUDIO256SE GD-1250, e-STUDIO256 GD-1250 Operator's Manual
Below you will find brief information for Fax Unit e-STUDIO6550C GD-1270, Fax Unit e-STUDIO306LP GD-1250, Fax Unit e-STUDIO856 GD-1250, Fax Unit e-STUDIO456 GD-1250, Fax Unit e-STUDIO4540C GD-1250. This manual describes how to use the fax functions, troubleshooting and maintenance of your new Fax Unit. You can learn how to send and receive faxes, create a mailbox for storing documents and set different transmission conditions such as resolution, original mode and transmission mode. It also covers advanced functions such as polling communication, priority transmission, delayed transmission reservation and recovery transmission.
Advertisement
Advertisement
MULTIFUNCTIONAL DIGITAL SYSTEMS
Operator’s Manual for FAX Unit
©2011 - 2013 TOSHIBA TEC CORPORATION All rights reserved
Under the copyright laws, this manual cannot be reproduced in any form without prior written permission of TTEC.
Preface
Thank you for purchasing the Toshiba FAX Unit GD-1250/GD-1260/GD-1270.
This Operator's Manual describes how to use the fax functions, troubleshooting and its maintenance, etc.
Before using the fax functions, thoroughly read and understand this Operator's Manual. To ensure that the fax functions are used in optimum working conditions, keep this Operator's Manual in a handy place for future reference.
Preface 1
Notice to Users
For U.S.A. only
WARNING FCC Notice: Part 15 and Part 18
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
(e-STUDIO2040C/2540C/3040C/3540C/4540C, e-STUDIO5540C/6540C/6550C, e-STUDIO206L/256/306/356/456, e-STUDIO256SE/306SE/356SE/456SE, e-STUDIO556/656/756/856, e-STUDIO556SE/656SE/756SE/856SE) and Part
18 (e-STUDIO5540C/6540C/6550C, e-STUDIO556/656/756/856, e-STUDIO556SE/656SE/756SE/856SE, e-STUDIO306LP) of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this guide, may cause harmful interference to radio communications. Operation of this terminal in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.
Warning: Changes or modification made to this equipment, not expressly approved by Toshiba TEC or parties authorized by Toshiba TEC could void the user’s authority to operate the equipment.
WARNING FCC Notice: Part 68
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the rear cover of this equipment is a label that contains, among other information, a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
This device is equipped with a USOC RJ11C connector.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of
RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US: AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point (e.g., 03 is a REN of 0.3).
For earlier products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information, please contact Toshiba America Business
Solutions Electronic Imaging Division at 1-800-468-6744. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including Fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.)
In order to program this information into your Fax machine, you should complete the following steps: complete the setup
procedures listed for station ID number and name. See P.103 “Registering the terminal ID”.
CAUTION — To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.
2 Notice to Users
TOSHIBA AMERICA BUSINESS SOLUTIONS, INC.
9740 Irvine Blvd.
Irvine, CA 92618
For Canada only
NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal
Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier.
Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
The Ringer Equivalence Number of your facsimile is 0.3
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
CAUTION — To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.
This Class A digital apparatus complies with Canadian ICES-003.
AVIS: L’etiquette d’lndustrie Canada identifie le marériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministére n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.
Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’entreprise locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée de raccordement.
L’abonné ne doit pas oublier qu’il est possible que la conformité aux conditions énoncées ci-dessus n’empêche pas la dégradation du service dans certaines situations.
Les réparations de materiel homologué doivent être coordonnées par un représentant désigné par le fournisseur.
L’entreprise de télécommunications peut demander à l’utilisateur de débrancher un appareil à la suite de réparations ou de modifications effectuees par l’utilisateur ou à cause de mauvais fonctionnement.
Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’énergie électrique, des lignes téléphoniques et des canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rerales.
Avertissement: L’utilisateur ne doit pas tenter de faire ces raccordements luimême; il doit avoir recours à un service d’inspection des installations électriques, ou à un électricien, selon le cas.
L’indice d’equivalence de la sonnerie de ce matériel 0.3.
AVIS: L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition que la somme d’indices d’equivalence de la sonnerie de tous les dispositifs n’excède pas 5.
Notice to Users 3
ATTENTION – Pour réduire les risques d’incendie, utiliser uniquement des conducteurs de telecommunications 26 AWG au de section superleure.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
TOSHIBA OF CANADA LIMITED
Office Product Group
191 McNABB STREET
MARKHAM, ONTARIO L3R 8H2
For NEW ZEALAND only
“The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to the network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any is compatible with all of Telecom’s network services.”
“This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which it is designated. Telecom will accept no responsibility should difficulties arise in such circumstances.”
“This equipment should not be used any circumstances which may constitute a nuisance to other Telecom customers.”
“Not all telephones will respond to incoming ringing when connected to the extension socket.”
“This device is equipped with pulse dialling while the Telecom standard is DTMF tone dialling. There is no guarantee that
Telecom lines will always continue to support pulse dialling.”
“Use of pulse dialling, when this equipment is connected to the same line as other equipment, may give rise to bell tinkle or noise and may also cause a false answer condition. Should such problems occur, the user should NOT contact the
Telecom Faults Service.”
“This device is intended for Stand-alone connection and not in parallel with other telephone devices.”
“The call log incorporated in this equipment does not record all answered calls. The call log, therefore may not agree with the Telecom account which may include calls not shown on the log.”
“If a charge for local calls is unacceptable, the ‘Dial’ button should NOT be used for local calls. Only the 7-digits of the local number should be dialled from your telephone. DO NOT dial the area code digit or the '0' prefix.”
TOSHIBA (AUSTRALIA) PTY LIMITED
58 Lunn Avenue,
Mt Wellington 1072
New Zealand.
Phone: 64-9-570 8530
4 Notice to Users
For EU only
Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Working environment
From EMC (Electromagnetic Compatibility) point of view, the operation of this product is being restricted in following environments: y Medical Environments: This product is not certified as a medical product according to the Medical Product Directive 93/42/EEC.
y Domestic environments (e.g. a private living room with TV / Radio sets in the nearby surrounding area) because this is a so called EMC class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures!
Any consequences resulting from the use of this product in restricted working environments are not the responsibility of TOSHIBA
TEC.
The consequences of the use of this product in restricted working environments may be an electromagnetic interference with other devices or machines in the nearby surrounding area. This can result into malfunction including data loss / data error pertaining to this product or the other devices / machines involved in the electromagnetic interference.
Furthermore, for general safety reasons, the use of this product in environments with explosive atmospheres is not permitted.
CE compliance
This product is labelled with the CE mark in accordance with the provisions of the applicable European Directives, notably the Low
Voltage Directive 2006/95/EC, the Electromagnetic Compatibility Directive 2004/108/EC and the Radio Equipment and
Telecommunications Terminal Equipment Directive 1999/5/EC.
CE marking is the responsibility of TOSHIBA TEC GERMANY IMAGING SYSTEMS GmbH, Carl-Schurz-Str. 7, 41460 Neuss,
Germany, phone +49-(0)-2131-1245-0.
For a copy of the related CE Declaration of Conformity, please contact your dealer or TOSHIBA TEC.
Notice to Users 5
Before Reading This Manual
How to read this manual
Symbols in this manual
In this manual, some important items are described with the symbols shown below. Be sure to read these items before using this equipment.
Indicates a potentially hazardous situation which, if not avoided, could result in death, serious injury, or serious damage, or fire in the equipment or surrounding objects.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, partial damage to the equipment or surrounding objects, or loss of data.
Indicates information to which you should pay attention when operating the equipment.
Other than the above, this manual also describes information that may be useful for the operation of this equipment with the following signage:
Describes handy information that is useful to know when operating the equipment.
Pages describing items related to what you are currently doing. See these pages as required.
Model and series names in this manual
In this manual, each model name is replaced with the series name as shown below.
Model name
e-STUDIO5540C/6540C/6550C e-STUDIO2040C/2540C/3040C/3540C/4540C e-STUDIO206L/256/306/356/456/506, e-STUDIO256SE/306SE/356SE/456SE/506SE e-STUDIO556/656/756/856, e-STUDIO556SE/656SE/756SE/856SE e-STUDIO306LP
Series name in this manual
e-STUDIO6550C Series e-STUDIO4540C Series e-STUDIO456 Series e-STUDIO856 Series e-STUDIO306LP
Explanation for control panel and touch panel
y Illustrations for the control panel and the touch panel shown in this manual are those of the e-STUDIO4540C Series.
The control panel and the touch panel, including buttons and their functions, are common to all of the e-STUDIO4540C
Series, e-STUDIO456 Series, e-STUDIO856 Series and e-STUDIO306LP. The shape and location of some buttons on the control panel and the dimension of the touch panel of the e-STUDIO6550C Series differ from those of other series, however, the names and functions of the buttons and parts are the same.
y The details on the touch panel menus may differ depending on the operating environment such as whether options are installed.
y The illustration screens used in this manual are for paper in the A/B format. If you use paper in the LT format, the display or the order of buttons in the illustrations may differ from that of your equipment.
6 Before Reading This Manual
Description of original/paper direction
Paper or originals of A4, B5 or LT size can be placed either in a portrait direction or in a landscape direction. In this manual, “-R” is added to this paper size when this size of paper or original is placed in a landscape direction.
Example: A4 size original on the original glass
Placed in a portrait direction: A4 Placed in a landscape direction: A4-R
Paper or originals of A3, B4, LD or LG can only be placed in a landscape direction, therefore “-R” is not added to these sizes.
Trademarks
The company names and product names in this manual are the trademarks of their respective companies.
Regarding paper printed by e-STUDIO306LP
Avoid the following actions as paper printed by e-STUDIO306LP may discolor.
y Store for long period of time y
Leave in places exposed to high temperature, such as inside of a car y Leave in places exposed to direct sunlight y
Rub the print side hard with a rubber and the like
Accessories
Accessories Provided for GD-1250/GD-1270 y
Modular cable: 1 y Operator's Manual: 1
Before Reading This Manual 7
General Precautions
Disclaimer notice
The following notice sets out the exclusions and limitations of liability of TOSHIBA TEC CORPORATION (including its employees, agents and sub-contractors) to any purchaser or user (hereafter “User”) of the e-STUDIO2040C/2540C/
3040C/3540C/4540C and e-STUDIO5540C/6540C/6550C, including its accessories, options and bundled software
(hereafter “Product”).
1. The exclusion and limitations of liability referred to in this notice shall be effective to the fullest extent permissible at law. For the avoidance of doubt, nothing in this notice shall be taken to exclude or limit TOSHIBA TEC
CORPORATION’s liability for death or personal injury caused by TOSHIBA TEC CORPORATION’s negligence or
TOSHIBA TEC CORPORATION’s fraudulent misrepresentation.
2. All warranties, conditions and other terms implied by law are, to the fullest extent permitted by law, excluded and no such implied warranties are given or apply in relation to the Products.
3. TOSHIBA TEC CORPORATION shall not be liable for any loss, cost, expense, claim or damage whatsoever caused by any of the following:
- use of handling of the Product otherwise than in accordance with the manuals, including but not limited to the
Operator’s Manual, User’s Guide, and/or incorrect or careless handling or use of the Product;
- any cause which prevents the Product from operating or functioning correctly which arises from or is attributable to either acts, omissions, events or accidents beyond the reasonable control of TOSHIBA TEC CORPORATION including without limitation acts of God, war, riot, civil commotion, malicious or deliberate damage, fire, flood, or storm, natural calamity, earthquakes, abnormal voltage or other disasters;
- additions, modifications, disassembly, transportation, or repairs by any person other than service technicians authorized by TOSHIBA TEC CORPORATION; or
- use of paper, supplies or parts other than those recommended by TOSHIBA TEC CORPORATION.
4. Subject to paragraph 1, TOSHIBA TEC CORPORATION shall not be liable to Customer for:
- loss of profits, loss of sales or turnover; loss of or damage to reputation; loss of production; loss of anticipated savings; loss of goodwill or business opportunities; loss of customers; loss of, or loss of use of, any software or data; loss under or in relation to any contract; or
- any special, incidental, consequential or indirect loss or damage, costs, expenses, financial loss or claims for consequential compensation; whatsoever and howsoever caused which arise out of or in connection with the Product or the use of handling of the
Product even if TOSHIBA TEC CORPORATION is advised of the possibility of such damages.
TOSHIBA TEC CORPORATION shall not be liable for any loss, cost, expense, claim or damage caused by any inability to use (including, but not limited to failure, malfunction, hang-up, virus infection or other problems) which arises from use of the Product with hardware, goods or software which TOSHIBA TEC CORPORATION has not directly or indirectly supplied.
8 General Precautions
CONTENTS
Chapter 1 BEFORE USING FAX
Chapter 2 SENDING/RECEIVING A FAX
Chapter 3 CHECKING AND CANCELING THE COMMUNICATIONS
Chapter 4 ADVANCED FUNCTIONS
CONTENTS 9
Chapter 5 PRINTING LISTS AND REPORTS
Chapter 6 SETTING ITEMS
Chapter 7 TROUBLESHOOTING AND SPECIFICATIONS
10 CONTENTS
1.
BEFORE USING FAX
This chapter describes the basics of this equipment you should learn before you start using it.
1 BEFORE USING FAX
Description of Each Component
Control panel
This section describes the buttons on the control panel used for the fax functions. For any details of the control panel not covered in this document, refer to the Quick Start Guide.
e-STUDIO4540C Series / e-STUDIO456 Series / e-STUDIO856 Series / e-STUDIO306LP (GD-1250)
12
1 2
For example: e-STUDIO4540C Series
3
4
5
6
11
e-STUDIO6550C Series (GD-1270)
10 9 13 8 7
13
8
12
1
9
10
4
5
6
11 2 3 7
12 Description of Each Component
1 BEFORE USING FAX
1.BEFORE USING FAX
1. [FAX] button
Use this button to display the fax screen when you use the fax function.
When you use the Internet Fax function, you also press this button. For details of the Internet Fax function, refer to the Scanning Guide.
2. [USER FUNCTIONS] button
Use this button when you register/make settings such as initial setting for the fax function.
3. Digital keys
Use these keys to enter fax numbers, etc.
4. [FUNCTION CLEAR] button
Use this button to clear all current selected functions and return to the default settings.
5. [STOP] button
Use this button to stop any scanning in progress.
6. [START] button
Use this button to start scanning a document for fax transmission.
7. [CLEAR] button
Use this button to cancel entered numbers.
8. Alarm lamp
This lamp lights when an error occurs and this equipment needs some actions to be taken.
9. MEMORY RX
This lamp lights when there is a received fax which is not printed yet and its data are still in the memory.
10. LINE
This lamp lights when a telephone line is busy.
11. Touch panel
12. [PRINT] button
Use this button to print a SECURE RECEIVE fax job.
13. PRINT DATA lamp
This lamp lights when there is a received SECURE RECEIVE fax job.
This lamp does not light when the equipment is in the Super Sleep mode.
Description of Each Component 13
1 BEFORE USING FAX
Touch panel
This section describes the fax screen on the touch panel. For any details of the touch panel not covered in this document, refer to the Quick Start Guide.
1
2
3
4 5 6
1. Header area
The name of the currently selected function and buttons related to the current status of this equipment are shown here.
2. Message area
Various messages such as the status of this equipment and operating instructions are shown here.
3. Operation object area
Operation-related buttons and text boxes are shown here.
4. Alert message area
Messages are shown here to inform you of various alerts such as the replacement time of toner cartridges and waste toner boxes, or the existence of a received SECURE RECEIVE fax job.
5. Date and time
The current date and time are shown here.
6. [JOB STATUS] button
Use this button to view the job status or its history.
When this equipment is managed under the department management or user management, key in user information such as the department code, user name and password to display the operation screen. For details of the operation, refer to the Quick Start Guide.
14 Description of Each Component
1 BEFORE USING FAX
1.BEFORE USING FAX
Options
This section describes the options related to the fax function.
y
FAX Unit
This unit enables the use of the fax function.
e-STUDIO4540C Series / e-STUDIO456 Series / e-STUDIO856 Series / e-STUDIO306LP: GD-1250 e-STUDIO6550C Series: GD-1270 y
2nd Line for FAX Unit (GD-1260)
This board enables the use of 2 lines for sending and receiving faxes.
Description of Each Component 15
1 BEFORE USING FAX
Connecting Cables
Be sure that the power of this equipment is turned OFF before connecting the cables.
e-STUDIO4540C Series (GD-1250)
1
2
3
e-STUDIO6550C Series (GD-1270) e-STUDIO456 Series / e-STUDIO306LP (GD-1250)
3
2
1
16 Connecting Cables
3 2 1
1 BEFORE USING FAX
1.BEFORE USING FAX e-STUDIO856 Series (GD-1250)
1
2
3
1. LINE2
Connect a telephone line when the 2nd Line for FAX Unit (optional) is installed.
2. LINE
Connect a telephone line.
3. TEL
Connect an external telephone.
y Do not connect this equipment and the external telephone to a telephone connector in parallel.
y Use the external telephone without an answerphone (or with the function off) to be connected with the TEL.
Connecting Cables 17
2.
SENDING/RECEIVING A FAX
This chapter describes how to send and receive a fax.
2 SENDING/RECEIVING A FAX
Sending a Fax
Basic procedures
This section describes the basic procedures to send a fax. For details of in-depth operations, see the page under each procedure as required.
Besides the basic sending functions described in this page, there are various useful ways to send a fax. These procedures are described in the following pages.
1
Place the original(s).
Check the original size and scanning range, etc. Place the original(s) on the original glass or RADF (Reversing
Automatic Document Feeder) in the correct direction. (The illustration above shows the original placed on the original glass.)
2
Press the [FAX] button on the control panel.
The fax screen is displayed. If you leave the screen unattended for the period of the auto clear setting time (45 sec by manufacture default), the screen returns to the default one automatically.
3
Press [OPTION] and set the transmission conditions.
The transmission condition setting screen is displayed. Set the transmission conditions such as resolution, original mode, exposure and transmission mode, as required.
P.28 “Setting the transmission conditions”
20 Sending a Fax
2 SENDING/RECEIVING A FAX
2.SENDING/RECEIVING A FAX
4
Specify the recipient.
To specify the recipient, dial the number using the digital keys on the control panel or use the address book.
P.32 “Specifying the recipient”
5
To display the preview screen, press [PREVIEW].
The preview feature is not available for the e-STUDIO456 Series, the e-STUDIO856 Series or the e-STUDIO306LP.
6
Press [SEND].
The fax is sent or reserved.
y Alternatively, you can press the [START] button on the control panel.
y In the memory transmission mode, the original is scanned into memory. Once a connection has been made, this equipment automatically starts sending the scanned document. In the direct transmission mode, the fax number is dialed immediately, and the scanned document will be sent. (Transmission conditions can be set in the transmission condition setting screen.) y If memory becomes full during scanning in the memory transmission mode, that original will not be stored in memory. When that happens, reduce the number of originals you are sending, or try sending them in the direct transmission mode.
y
You can check the status of the current sending. You can also cancel the transmission (deletes the job).
P.47 “CHECKING AND CANCELING THE COMMUNICATIONS”
Sending a Fax 21
2 SENDING/RECEIVING A FAX
Redial function
In the memory transmission mode, if the fax cannot be sent due to a busy-line, the fax number is redialed automatically to send the fax. By default, this equipment redials 3 times at 1-minute intervals.
Batch transmission function
If there are multiple transmission jobs to the same recipient in memory, you can send them at once using this function, resulting in reduction of communication costs. However, if their recipients are the same but their transmission conditions vary or if users or departments are different when this equipment is managed under the department management or user management, this function is not applied to those reserved jobs.
Sending the next original
If an original is placed on the original glass and its scanning is completed, the confirmation screen for the next original is displayed. If you want to continue scanning of the next original, place it on the original glass, and then press the [START] button on the control panel. Once all the originals are scanned, press [JOB FINISH]. If you place an original on the RADF
(Reversing Automatic Document Feeder) and press the [CONTINUE] button during scanning, the confirmation screen for the next original can be displayed after the scanning is completed.
y If you leave the screen unattended for a period of the auto clearance setting time (45 sec. by manufacturer default), a copy of the scanned originals is sent.
y To cancel the transmission in the memory transmission mode, press [JOB CANCEL].
P.51 “Canceling the memory transmission”
y To change the transmission conditions for each page, press [OPTION].
P.31 “Changing the settings for each page”
22 Sending a Fax
2 SENDING/RECEIVING A FAX
2.SENDING/RECEIVING A FAX
Handling an original
Originals that can be sent
This equipment can send a fax of the following originals.
You can place 1-sided or 2-sided originals of the media types, such as standard paper, recycled paper and paper having holes (2, 3 or 4 holes) for filing, on the RADF (Reversing Automatic Document Feeder). On the original glass, you can place 1-sided originals of the above media types as well as OHP film, tracing paper, booklets and three-dimensional objects.
Location
Original glass
Maximum size
Length: 297 mm (11.69")
Width: 432 mm (17.01")
Paper weight
−
RADF* Length: 297 mm (11.69")
Width: 432 mm (17.01") e-STUDIO4540C Series / e-STUDIO456 Series / e-STUDIO306LP:
1-sided originals
35 - 157 g/m
2
(9.3 - 41.8 lb.)
2-sided originals
50 - 157 g/m
2
(13.3 - 41.8 lb.) e-STUDIO6550C Series / e-STUDIO856 Series:
1-sided originals
35 - 209 g/m
2
(9.3 - 110 lb.)
2-sided originals
50 - 157 g/m 2 (13.3 - 41.8 lb.)
* For e-STUDIO4540C Series / e-STUDIO456 Series / e-STUDIO306LP, RADF is an option.
Original size
North American format:
LD, LG, LT, LT-R, ST, ST-R,
COMP
A/B format:
A3, A4, A4-R, A5, A5-R, B4,
B5, B5-R, FOLIO
North American format:
LD, LG, LT, LT-R, ST-R,
COMP
A/B format:
A3, A4, A4-R, A5-R, B4, B5,
B5-R, FOLIO
(ST/A5 is not available) y Do not place any heavy objects (4 kg/9 lb. or over) on the original glass and do not press on it with force.
y If the original is any of the following sizes, it is automatically rotated and sent as described below.
A4
→ A4-R
A5-R
→ A5
B5-R
→ B5
LT
→ LT-R
ST-R
→ ST y You need to select the original size by yourself when placing the following originals whose sizes cannot be detected correctly:
- Highly transparent originals (e.g. overhead transparencies, tracing paper)
- Totally dark originals or originals with dark borders
- Non-standard size originals (e.g. newspapers, magazines)
For details, refer to the Copying Guide.
Sending a Fax 23
2 SENDING/RECEIVING A FAX
Original scanning range
The following figures show the original scanning area. Any information in the shaded area is not printed on the paper.
1. LD, LG, LT-R, ST-R, COMP, A3, A4-R, A5-R, B4, B5-R, FOLIO
2. LT, ST, A4, A5, B5
1 2
5 mm
(0.2 inch)
5 mm
(0.2 inch)
5 mm
(0.2 inch)
5 mm
(0.2 inch)
5 mm
(0.2 inch)
5 mm
(0.2 inch)
5 mm
(0.2 inch)
5 mm
(0.2 inch)
24 Sending a Fax
2 SENDING/RECEIVING A FAX
2.SENDING/RECEIVING A FAX
Placing the original(s) on the original glass
This section describes how to set an original on the original glass. Originals are sent in the order they are placed on the original glass.
Do not place any heavy objects (4 kg/9 lb. or over) on the original glass and do not press on it with force.
Breaking the glass could injure you.
1
Raise the Original Cover or RADF (Reversing Automatic Document Feeder), and place the original with its face down on the glass.
Raise it 60 degrees or more for the detection of the original.
2
Align the original against the left inner corner of the glass.
A
B y Different size originals can also be sent in one transmission.
y When an original of any size other than LT/A4 is placed in the direction shown in the above left figure, transmission to a recipient is carried out so that the pre-entered sender information is printed in position A in the figure.
y When an original of LT/A4 size is placed in the direction shown in the above right figure, transmission to a recipient is carried out so that the pre-entered sender information is printed in position B in the figure.
y The pre-entered sender information shows what is registered in the Terminal ID.
P.103 “Registering the terminal ID”
3
Lower the Original Cover or RADF slowly.
Sending a Fax 25
2 SENDING/RECEIVING A FAX
Placing the original(s) on the RADF
This section describes how to set the original(s) on the RADF (Reversing Automatic Document Feeder, optional). When the originals are placed on the RADF, the uppermost page is the first to be scanned and sent.
For e-STUDIO4540C Series / e-STUDIO456 Series / e-STUDIO306LP, RADF is an option.
1
After aligning the originals, place them with their face up and slide the guides to rest against the edges of the originals.
y Regardless of their sizes, originals are acceptable up to 100 sheets (35 to 80 g/m
2
(9.3 to 20 lb.)) or 16 mm
(0.62") in height.
y 2-sided originals can be set and sent.
P.56 “Transmitting 2-Sided Originals”
A
B y When an original of any size other than LT/A4 is placed in the direction shown in the above left figure, transmission to a recipient is carried out so that the pre-entered sender information is printed in position A in the figure.
y When an original of LT/A4 size is placed in the direction shown in the above right figure, transmission to a recipient is carried out so that the pre-entered sender information is printed in position B in the figure.
y The pre-entered sender information shows what is registered in the Terminal ID.
P.103 “Registering the terminal ID”
26 Sending a Fax
2 SENDING/RECEIVING A FAX
2.SENDING/RECEIVING A FAX
Sending different width originals
To set different width originals, adjust the side guides to the widest original size, and then align the original against the front side. Available combinations of the original size are as follows.
y A/B format: A3, A4, B4, B5, A4-R, FOLIO y
North American format: LD, LT, COMP, LG, LT-R
To send different width originals, you need to enable “DIFFERENT WIDTH” as a transmission condition.
P.28 “Setting the transmission conditions”
Precautions for using the RADF
Do not use the following originals as they may misfeed or become damaged:
(1) Badly wrinkled or folded originals. In particular, originals whose leading edge are curled may fail to be fed.
(4) Clipped or stapled originals
(2) Originals with carbon paper (5) Originals with holes or torn originals
(3) Taped, pasted or clipped (cut out) originals
(6) Damp originals (7) OHP film originals
The following originals should be handled carefully:
(1) Folded or curled originals should be smoothed out before being used.
(2) Originals sticking to each other, or originals that are surface-treated may fail to separate properly.
Sending a Fax 27
2 SENDING/RECEIVING A FAX
Setting the transmission conditions
You can set the fax transmission conditions.
y The transmission conditions are only applied to the current transmission. They return to the default settings after the transmission.
y Each default setting of resolution, original mode, exposure, transmission mode and ECM is adjustable.
Making settings
Pressing [OPTION] on the fax screen will display the transmission condition setting screen as shown below. Set each setting item, and then press [OK].
y Press or to switch the pages.
y To cancel the operation and return to the previous screen, press [RESET].
28 Sending a Fax
2.SENDING/RECEIVING A FAX
RESOLUTION
Set the resolution based on the fineness of the original.
STANDARD: This is suitable for an original with regular size text.
FINE:
U-FINE:
This is suitable for an original with small size text and fine illustrations.
This is suitable for an original with ultra-fine illustrations.
2 SENDING/RECEIVING A FAX
If the recipient’s fax machine is not capable of receiving originals at the same resolution, the resolution is automatically converted before being sent to the recipient. The higher the resolution is, the longer it takes to send an original.
TX TYPE
Set the fax transmission mode.
MEMORY TX: Send the original after the scanned data are saved in the memory. Up to 100 transmissions can be reserved. Up to 1000 pages can be sent in one transmission.
DIRECT TX: Send the original directly as it is being scanned. Once a page has been scanned and sent, the next page is scanned and sent. Therefore, it takes longer to scan and send all pages. However, you can confirm on the fly that each page is sent to the recipient.
ORIGINAL MODE
Set the scanning mode based on the type of the original.
TEXT: This is suitable for an original with text and line drawings.
TEXT/PHOTO: This is suitable for an original with a mixture of text and photos.
PHOTO: This is suitable for an original with photos.
y In the TEXT/PHOTO mode or PHOTO mode, transmission time may be longer than that in the TEXT mode.
y
To scan originals printed with erasable toner, select TEXT mode.
ORIGINAL SIZE
Set the scan size of the original.
AUTO: The size of the original is automatically determined before the original is scanned.
DIFFERENT WIDTH: Select this function to load the originals with different width into the RADF (Reversing
Automatic Document Feeder).
Specified size: The original is scanned at the preset size regardless of its actual size.
If the recipient’s fax machine is not capable of receiving originals of B5/B5-R size, this equipment may reduce that size before sending it. To avoid this, when the original to be set is B5 and B5-R size, specify A4 and A4-R size respectively.
EXPOSURE
Set the density at which the original is to be scanned.
AUTO: This equipment automatically detects the contrast of the original, and scans it with the optimum density.
Manual:
Press or to set the desired contrast.
Sending a Fax 29
2 SENDING/RECEIVING A FAX
ECM
Switch the ECM (Error Correction Mode) communication ON or OFF. ECM is an internationally standardized communication mode that automatically corrects errors that occur during fax transmissions. With this setting option ON, even when the transmitted data have been affected by noise during communication, this mode allows good communication without image distortion by automatically resending the parts that have been affected.
y Both the sender and the receiver must have the ECM function to make ECM communication available.
y When affected by noise during communication, communication time is slightly longer than usual. Even when the
ECM communication is used, an error may occur depending on the line status.
y The ECM communication is not available for voice communication.
QUALITY TX
Switch Quality TX ON or OFF. When this mode is set to ON, originals are sent at a slower speed than usual and the chances of errors occurring decrease.
MAIL BOX COMMUNICATION
For the communication compatible with ITU-T (International Telecommunications Union-Telecommunications) standards, specify a subaddress or password to be sent to the recipient's fax machine. (Up to 20 digits can be entered.)
SUB (Subaddress): Information to send data of the original to the fax machine.
SEP (Selective Polling):
SID (Sender Identification):
PWD (Password):
Information to retrieve data of the original from the fax machine.
Password for SUB.
Password for SEP.
To use this function, the recipient’s fax machine must be capable of setting an ITU-T compatible subaddress or password.
INTERNET FAX
SUBJECT: The subject of the Internet Fax
BODY: The body of the Internet Fax
This is not used for sending a standard fax.
LINE SELECT
Specify the line to be used for sending a fax when the 2nd Line for FAX Unit (optional) is installed.
P.109 “Setting 2nd Line for FAX Unit”
AUTO: The line is switched automatically.
LINE 1: The 1st line is used.
LINE 2: The 2nd line is used.
30 Sending a Fax
2 SENDING/RECEIVING A FAX
2.SENDING/RECEIVING A FAX
Changing the settings for each page
You can change the scanning conditions (RESOLUTION, MODE, EXPOSURE and ORIGINAL) for each page.
1
Specify the recipients and press [SEND] to start scanning a document. When the scanning of the original is completed, the confirmation screen for the next original is displayed. Press [OPTION].
The illustration above shows the original placed on the original glass. If you place an original on the RADF
(Reversing Automatic Document Feeder) and press the [CONTINUE] button during scanning, the confirmation screen for the next original is displayed after the scanning is completed. If you press the [STOP] button during scanning, the scanning halts and the confirmation screen for the next original can be displayed.
2
The setting screen for the scanning conditions is displayed. Change the setting, and then press [OK].
Sending a Fax 31
2 SENDING/RECEIVING A FAX
Specifying the recipient
There are various ways to specify the recipient, such as Direct entry with the control panel and Address book entry.
To use the address book, you need to register recipients’ fax numbers to the book in advance. For details of the operation, refer to the MFP Management Guide or TopAccess Guide.
Direct entry with digital keys
You can specify the recipient by entering its fax number on the control panel.
1
Press [INPUT FAX No].
2
Key in the recipient's fax number and press [OK].
y
You can also enter the recipient's address with the digital key on the control panel.
y To delete the entered fax number one number at a time, press [BACK SPACE].
y To delete the entire entered fax number in one go, press the [CLEAR] button.
32 Sending a Fax
2.SENDING/RECEIVING A FAX
3
Confirm the fax number displayed on the fax screen.
2 SENDING/RECEIVING A FAX
y To delete each entered value, press [BACK SPACE].
y To delete all the entered values at once, press the [CLEAR] button on the control panel.
y To confirm all the selected recipients or delete unnecessary recipients, press [DESTINATION].
P.38 “Confirming the recipients”
To send to multiple addresses
In the memory transmission mode, you can send the same document to multiple recipients (up to 400 recipients) at once. Press [MULTI], and then enter the recipient's fax number. Repeat this operation until you specify all the recipients. You can also specify up to a total of 400 recipients' fax numbers by combining with other entry methods.
Specifying the recipient in the address book
In the address book, you can specify the recipient.
1
Press [SINGLE] tab to display the list of the addresses, and then press the recipient’s
FAX icon ( ).
y Press or to switch the pages.
y Alternatively, you can select the recipient by pressing the address name box. In such case, if a fax number and an E-mail address have been registered to the recipient's address, both of them are selected.
y To cancel the selected recipient, press it again.
y To confirm all the selected recipients or delete unnecessary recipients, press [DESTINATION].
P.38 “Confirming the recipients”
y To refine your search only for items including specified characters, press the pull-up menu.
y A list of recipients can be displayed using 11 to 15 characters per name.
To send to multiple addresses
In the memory transmission mode, you can send the same document to multiple recipients (up to 400 recipients) at once. Repeat this selection until you select all the recipients. For the multi-address transmission, you can also specify the recipients (up to a total of 400 recipients) by combining with other entry methods.
Sending a Fax 33
2 SENDING/RECEIVING A FAX
Group entry
In the address book, you can specify the group to which you want to send a fax.
1
Press [GROUP] tab to display the list of the groups, and then press the group name.
y Press or to switch the pages.
y To cancel the selected group, press it again.
y To confirm the addresses registered in that group, press [CONTENTS].
y To confirm all the selected recipients or delete unnecessary recipients, press [DESTINATION].
P.38 “Confirming the recipients”
y To refine your search only for items including specified characters, press the pull-up menu.
To send to multiple addresses
In the memory transmission mode, you can specify multiple groups (up to 200 groups, up to a total of 400 recipients) to send the same document at once. Repeat this selection until you select all the recipients. For the multi-address transmission, you can also specify the recipients (up to a total of 400 recipients) by combining with other entry methods.
Searching by ID number
You can search for a specific recipient from the address book using the ID number.
1
Press [KNOWN ID].
34 Sending a Fax
2 SENDING/RECEIVING A FAX
2.SENDING/RECEIVING A FAX
2
Key in the desired ID number (1 to 1000) using the digital keys on the control panel, and then press [OK].
The ID number is the one shown in the destination name box. The number ranges from 001 to 1000.
3
The page including the entered ID number is displayed. Press the FAX icon ( ).
y Press or to switch the pages.
y Alternatively, you can select the recipient by pressing the address name box. In such case, if a fax number and an E-mail address have been registered to the recipient's address, both of them are selected.
y To cancel the selected recipient, press it again.
y To confirm all the selected recipients or delete unnecessary recipients, press [DESTINATION].
P.38 “Confirming the recipients”
To send to multiple addresses
In the memory transmission mode, you can send the same document to multiple recipients (up to 400 recipients) at once. Repeat this selection until you select all the recipients. For the multi-address transmission, you can also specify the recipients (up to a total of 400 recipients) by combining with other entry methods.
Sending a Fax 35
2 SENDING/RECEIVING A FAX
Searching for the recipient's fax number
You can search for the recipient's fax number from the address book and LDAP server.
To search for the recipient's fax number from the LDAP (Lightweight Directory Access Protocol) server, the name of the LDAP server to be connected is required to be registered to this equipment in advance. For details of the LDAP server, ask your network administrator.
1
Press [SEARCH].
y To display the recipient search menu, press [SEARCH] while the address list is displayed. Perform this operation when you want to search the LDAP server.
y To display the group search menu, press [SEARCH] while the group list is displayed.
2
Press the button of the keyword category you want to search. Enter the keyword. Press
[SEARCH].
y For details of the operation to enter characters, refer to the Quick Start Guide.
y To cancel the entered keyword, press [CLEAR].
y
You can search for the desired recipient's fax number by specifying multiple keywords.
36 Sending a Fax
2 SENDING/RECEIVING A FAX
2.SENDING/RECEIVING A FAX
Selecting the LDAP server
To search for the recipient's fax number in the LDAP server, press the pull-down menu in the recipient search menu. The list of the LDAP servers is displayed. Press the LDAP server name you want to search, and then press
[OK].
3
The search result is displayed. Press the desired FAX icon ( ), and then press [OK].
y Press or to switch the pages.
y Alternatively, you can select the recipient by pressing the address name box. In such case, if a fax number and an E-mail address have been registered to the recipient's address, both of them are selected.
y To cancel the selected recipient, press it again.
y To confirm all the selected recipients or delete unnecessary recipients, press [DESTINATION].
P.38 “Confirming the recipients”
To send to multiple addresses
In the memory transmission mode, you can send the same document to multiple recipients (up to 400 recipients) at once. Repeat this selection until you select all the recipients. For the multi-address transmission, you can also specify the recipients (up to a total of 400 recipients) by combining with other entry methods.
Sending a Fax 37
2 SENDING/RECEIVING A FAX
Confirming the recipients
You can confirm the recipients which you specified or delete unnecessary recipients.
1
Press [DESTINATION].
2
The recipient list screen is displayed. Select the recipient you want to delete, and then press [DELETE].
y Press or to switch the pages.
y Press [CLOSE] to return to the previous screen.
38 Sending a Fax
2 SENDING/RECEIVING A FAX
2.SENDING/RECEIVING A FAX
Other transmissions
On-hook transmission
In this mode, you can dial and perform direct fax transmission without picking up the handset of the external telephone.
On-hook Transmission is available when on the upper right of the screen is OFF.
1
Place the original(s).
2
Press the [FAX] button on the control panel.
3
Press [OPTION] and set the transmission conditions.
P.28 “Setting the transmission conditions”
4
Press [MONITOR].
y Make sure that you hear the dial tone from the built-in speaker.
y To cancel the operation, press [MONITOR] again.
To use the [SEARCH] to specify the recipients, you must specify the recipient in advance by following the procedures below. Specify the recipients, and then press [MONITOR].
5
Specify the recipients.
P.32 “Specifying the recipient”
y For direct entry, each press of a digital key on the control panel dials a number. If you make a mistake when dialing the fax number, press [MONITOR] to cut the line, and then press it again to redial.
y If you specified the recipient with the [SEARCH], press [MONITOR], and then [DIAL].
6
When you hear the answer tone (short high-pitched tone) through the built-in speaker indicating the connection has been made with the recipient’s machine, press [SEND].
When you hear the other party’s voice answering the call before pressing [SEND], pick up the handset of the external telephone. Then ask him/her to perform operation of the fax reception.
Sending a Fax 39
2 SENDING/RECEIVING A FAX
Off-hook transmission
In this mode, you can pick up the handset of the external telephone to dial and perform direct fax transmission. Off-hook
Transmission is available when on the upper right of the screen is OFF.
1
Place the original(s).
2
Press the [FAX] button on the control panel.
3
Press [OPTION] and set the transmission conditions.
P.28 “Setting the transmission conditions”
4
Pick up the handset of the external telephone.
5
Use the external telephone to dial the fax number.
P.32 “Specifying the recipient”
When you use the external telephone to dial, the machine dials each number you enter. If you make a mistake when dialing the fax number, replace the handset to cut the line, and then pick up the handset again to redial.
6
When you hear the answer tone (short high-pitched tone) through the built-in speaker indicating the connection has been made with the recipient’s machine, press [SEND].
When you hear the other party’s voice answering the call before pressing [SEND], ask him/her to perform operation of the fax reception.
7
Replace the handset of the external telephone.
Displaying the preview
Before sending a fax, you can check the image on the touch panel with this preview function.
The preview feature is not available for the e-STUDIO456 Series, the e-STUDIO856 Series or the e-STUDIO306LP.
1
Press [PREVIEW] on the fax menu.
y To use the preview function, specify the recipient and then press [PREVIEW].
40 Sending a Fax
2 SENDING/RECEIVING A FAX
2.SENDING/RECEIVING A FAX
2
Press [SEND].
3
Check the fax image after the preview is displayed. Press [OK] if you send it without any change. The fax will then be sent.
y
To send another original, place it on the original glass or RADF (Reversing Automatic Document Feeder), and then press the [START] button on the control panel.
y To delete the page being previewed, press [DELETE PAGE].
y To replace the page being previewed with another page, press [REPLACE PAGE].
y To insert another scan before the page being previewed, press [INSERT PAGE].
y Press [OPTION] to change the setting.
P.28 “Setting the transmission conditions”
Sending a Fax 41
2 SENDING/RECEIVING A FAX
Receiving a Fax
Reception mode
This section describes how to receive a fax. Refer to the appropriate section for your current reception mode. The reception mode can be set on the ADMIN menu. For details of the current setting, ask your administrator. Besides the receiving methods described in this page, there are various useful ways to receive a fax. These procedures are described in the following pages.
AUTO reception
Faxes are automatically received during an incoming call. Users do not have to do anything when receiving a fax.
When the 2nd Line for FAX Unit (optional) is installed, the reception mode of the 2nd line is limited to “AUTO reception”.
MANUAL reception
Faxes are manually received by using an external telephone when you have an incoming call.
1
Pick up the handset of the external telephone when you have an incoming call.
If the incoming call is a telephone call, you can start talking.
2
If you hear a tone (fax signal) through the handset of the external telephone, press the
[FAX] button on the control panel.
3
Press the [ADVANCED] tab, and then press [MANUAL RECEIVE].
4
When a message appears indicating that you can send a fax, press the [START] button on the control panel and replace the handset of the external telephone.
42 Receiving a Fax
2 SENDING/RECEIVING A FAX
2.SENDING/RECEIVING A FAX
Memory reception
In the following conditions, faxes cannot be printed. If this happens, received fax data are stored in the memory, and printing is resumed as soon as this equipment is ready. As the memory reception function is always enabled, you do not need to make any setting.
y
During copying or printing y During printing of received copy of the originals y During printing of lists and reports y When paper has run out y When a paper jam occurs y When toner has run out
Receiving a Fax 43
2 SENDING/RECEIVING A FAX
Originals and paper
Acceptable size of paper
A3, B4, A4, B5, A5, FOLIO, LD, LG, LT, ST and COMP sized paper are available.
The printing range of each size of paper is as follows: As shown in the figures below, if an original document contains any information in the shaded area, it is not printed on the paper.
5 mm
(0.2 inch)
5 mm
(0.2 inch)
5 mm
(0.2 inch)
5 mm
(0.2 inch)
5 mm
(0.2 inch)
5 mm
(0.2 inch)
5 mm
(0.2 inch)
5 mm
(0.2 inch) y Set the paper in the drawers or the Large Capacity Feeder (optional). The bypass tray is not available.
y Regardless of whether or not the Finisher (optional) is installed, paper exits on the receiving tray.
y Drawers can be set for fax use only. For details of the operation, refer to the Copying Guide.
Default setting for RX printing
To print the received fax, the paper with the same width as the original is used. Depending on the length of the original,
“RX reduction printing” or “Discard printing” (both of them are set to ON by manufacture default) are applied.
When an original is shorter or the same as the paper printing area
It is printed in the original size.
When an original is longer than the paper printing area
It is printed according to the following priority: y When an original is up to 10 mm (0.4 inch) longer than the printing area: the part of the originals that exceeds the paper printing area is discarded.
y When an original exceeds the printing area by more than 10 mm (0.4 inch): the original image is reduced to 75 %
(reduction printing). If the image still cannot be fitted into the printing area, paper larger than the original is selected. In case there is no larger paper available, the original is printed with the image divided.
44 Receiving a Fax
2 SENDING/RECEIVING A FAX
2.SENDING/RECEIVING A FAX
Paper priority when there is no same size paper
When both “RX reduction printing” and “Discard printing” are set to ON, paper is selected according to the following priority:
1. Paper of the same size and the same orientation as the original
2. Paper of the same size but with a different orientation to the original
3. Paper of the same orientation but larger than the original
North American format
Size of Original being Received
Ledger Legal Letter Letter Statement COMP
Priority
1
Ledger Legal Letter Letter Statement COMP
2
Letter
Reduced to 75%
Letter Letter Letter Ledger
3
Letter
Reduced to 75%
Ledger Legal Letter
4
COMP Legal COMP Legal
5
Ledger COMP Ledger COMP
6
Ledger y When the corresponding paper size is not available, in most cases, the scanned original is printed on paper of a larger size. However, the sender’s fax machine may reduce the scanned original to fit the paper size available in the recipient’s fax machine (this equipment). (Ex. LD
→ LT) y
The paper priority varies according to the “RX reduction printing” and “Discard printing” settings. For details, contact your service technician.
Receiving a Fax 45
2 SENDING/RECEIVING A FAX
6
7
4
5
A/B format
Size of Original being Received
Priority
A3
1
A3
2
3
B4
B4
A3
A4
A4
A4
A3
B4
A4
A4
A4
B4
A3
B5
B5
B5
B4
A4
A4
A3
A5
FOLIO
A5
FOLIO
A4
A4
A3
B5
A4
Reduced to 75%
B5
A4
Reduced to 75%
B4
B4
A3 y
When the corresponding paper size is not available, in most cases, the scanned original is printed on paper of a larger size. However, the sender’s fax machine may reduce the scanned original to fit the paper size available in the recipient’s fax machine (this equipment). (Ex. A3
→ A4) y The paper priority varies according to the “RX reduction printing” and “Discard printing” settings. For details, contact your service technician.
46 Receiving a Fax
3.
CHECKING AND CANCELING THE
COMMUNICATIONS
This chapter describes how to check and cancel fax communications.
3 CHECKING AND CANCELING THE COMMUNICATIONS
Checking Communications
Checking reserved transmissions
You can check reserved fax transmissions.
1
Press [JOB STATUS].
2
Select [FAX].
y Reserved transmission jobs are listed in the reversed chronological order from top to bottom.
y Press or to switch the pages.
y To print the list of the reserved transmissions jobs, press [RESERVATION LIST].
y In the “Status” column, the status of each job is indicated as follows:
Line1: Sending on the 1st line.
Line2: Sending on the 2nd line.
Network: Reserved for sending via Internet Fax.
Delayed: Reserved with the time to send specified.
Wait:
Invalid:
Communication is in the standby queue.
Under standby due to an invalid department code (Network Fax). For details of Network Fax function, refer to the Network Fax Guide.
48 Checking Communications
3.CHECKING AND CANCELING THE COMMUNICATIONS
Checking communication status (log)
You can check the log of fax transmissions and receptions.
1
Press [JOB STATUS].
3 CHECKING AND CANCELING THE COMMUNICATIONS
2
Select the [LOG] tab, and then press [SEND] or [RECEIVE].
Checking Communications 49
3 CHECKING AND CANCELING THE COMMUNICATIONS
3
The list of the communication status is displayed.
y Transmissions or receptions are listed in the reversed chronological order from top to bottom.
y Press or to switch the pages.
y Up to the latest 40 or 120 transmission/reception records can be listed on the log. The maximum number can be set on the ADMIN menu. For details of the operation, refer to the MFP Management Guide.
y To print the log of transmissions or receptions, press [JOURNAL].
P.84 “Journal (transmission journal/reception journal)”
y In the “Status” column, the status is indicated as follows:
OK: Transmission or reception succeeded.
4-digit error code: Transmission or reception failed.
Registering recipients’ fax numbers to the address book
To register recipient's fax numbers in the address book from the send/receive log screen, select a record in the send or receive log, and then press [ENTRY]. For details of the registration to the address book, refer to the MFP
Management Guide.
y Fax and E-mail transmissions whose recipients are specified with direct entry or entry using the LDAP server can be registered to the address book from the Send log.
y Polling and E-mail receptions whose recipients are specified with direct entry or entry using the LDAP server can be registered to the address book from the Receive log.
50 Checking Communications
3 CHECKING AND CANCELING THE COMMUNICATIONS
Canceling the Transmission
Canceling the memory transmission
You can cancel the memory transmission during scanning.
When using the original glass
This section describes how to cancel the memory transmission when an original is placed on the original glass.
1
When scanning is completed, the confirmation screen for the next original is displayed.
Press [JOB CANCEL].
If you leave the screen unattended for a period of the auto clearance setting time (45 sec. by manufacturer default) after the confirmation screen for the next original is displayed, a copy of the scanned originals is sent.
2
The confirmation screen for the deletion is displayed. Press [YES].
Canceling the Transmission 51
3 CHECKING AND CANCELING THE COMMUNICATIONS
When using the RADF (Reversing Automatic Document Feeder)
This section describes how to cancel the memory transmission when an original is placed on the RADF.
1
Press the [STOP] button on the control panel while the originals are being scanned.
Scanning is paused.
2
The confirmation screen for the next original is displayed. Press [JOB CANCEL].
y If you press [JOB FINISH], the scanned originals are sent.
y If you leave the screen for the next original unattended for the period of the auto clear setting time (45 sec. by manufacture default) after it appears, the memory transmission is canceled.
3
The confirmation screen for the deletion is displayed. Press [YES].
52 Canceling the Transmission
3 CHECKING AND CANCELING THE COMMUNICATIONS
3.CHECKING AND CANCELING THE COMMUNICATIONS
Canceling direct transmissions
You can cancel the direct transmission during scanning.
Even if you cancel transmission in the direct TX mode, the part of the original that was scanned before transmission is canceled has been sent.
1
Press the [STOP] button on the control panel while the original is being scanned.
The scanning and transmission are stopped.
Canceling the Transmission 53
3 CHECKING AND CANCELING THE COMMUNICATIONS
Canceling reserved transmissions
You can display the list of the reserved transmissions, and cancel the reserved transmissions that are in the queue or in progress.
1
Press [JOB STATUS], and then select the [FAX] tab.
The list of the reserved transmissions is displayed. This step is the same as that for checking the reserved transmission.
P.48 “Checking reserved transmissions”
2
Select the reserved transmission you want to delete, and then press [DELETE].
More than one job can be selected.
In the “Status” column, you can check the status of the reservation. “Wait” indicates that the data are waiting to be sent. “Line1” or “Line2” indicates that the data are being sent. Delayed transmission reservation and polling transmission/reception can be canceled.
3
The confirmation screen for the deletion is displayed. Press [DELETE].
54 Canceling the Transmission
4.
ADVANCED FUNCTIONS
This chapter describes useful functions of this equipment.
4 ADVANCED FUNCTIONS
Transmitting 2-Sided Originals
You can send a copy of 2-sided originals by fax using the RADF (Reversing Automatic Document Feeder).
Note that each setting will automatically return to its default setting when transmission is completed.
1
Place the original(s) on the RADF.
When you place a 2-sided original of the LT/A4 size, change the direction of the original depending on its bound position as follows:
1. Right-to-left (book-type) original
2. Top-to-bottom (tablet-type) original
1 2
2
Press the [FAX] button on the control panel.
3
Press [OPTION] and set the transmission conditions.
P.28 “Setting the transmission conditions”
4
Select the [ADVANCED] tab, and then press [2-SIDED SCAN].
5
Press [BOOK] or [TABLET] depending on the bound position of the original(s), and then press [OK].
56 Transmitting 2-Sided Originals
4.ADVANCED FUNCTIONS
6
Specify the recipient’s fax number.
P.32 “Specifying the recipient”
7
Press [SEND].
4 ADVANCED FUNCTIONS
Transmitting 2-Sided Originals 57
4 ADVANCED FUNCTIONS
Priority Transmission
You can send a fax prior to other reserved transmissions (including redial standby).
Note that each setting will automatically return to its default setting when transmission is completed.
1
Place the original(s).
2
Press the [FAX] button on the control panel.
3
Press [OPTION] and set the transmission conditions.
P.28 “Setting the transmission conditions”
4
Press the [ADVANCED] tab, and then press [PRIORITY RESERVE].
5
Press [OK].
6
Specify the recipient’s fax number.
P.32 “Specifying the recipient”
In the priority transmission mode, you cannot specify multiple recipients’ fax numbers.
7
Press [SEND].
58 Priority Transmission
4 ADVANCED FUNCTIONS
Polling Communication
The polling communication function allows you to receive pending originals in the sender's fax machine by manually operating the receiving fax machine. In this document, the operation in which this equipment is used as the sender's fax machine is called “polling transmission” while that in which it is used as the recipient's fax machine is called as “polling reception”.
Polling transmission
Upon request of a recipient's fax machine, this equipment sends an original document stored into the memory to the recipient. By setting a password and/or a recipient's fax number to an original stored into the memory, you can permit specific recipients to receive the original using the polling transmission.
To use the polling communication function with the password verification applied, the fax machines of both the sender and recipient have to be Toshiba Fax machines (MFP).
1
Place the original(s).
2
Press the [FAX] button on the control panel.
3
Press [OPTION] and set the transmission conditions.
P.28 “Setting the transmission conditions”
4
Press the [ADVANCED] tab, and then press [POLLING RESERVE].
5
To set the password and/or fax number (the recipient’s telephone number), press the
[PASSWORD] and/or [FAX NUMBER] button. On the entry screen that appears, key in the password (4 digits) and/or fax number (a maximum of 20 digits), and then press
[OK].
y
You do not have to set both the password and the fax number.
y If you have to set neither a password nor a fax number, leave both blank and press [OK].
Polling Communication 59
4 ADVANCED FUNCTIONS
6
Press the [START] button on the control panel.
y Upon request of the recipient's fax machine, the data of the original stored into memory are sent automatically.
Once they are sent, they are deleted from memory.
y You can delete the data of the original from memory by canceling the polling transmission.
P.54 “Canceling reserved transmissions”
Polling reception
This equipment requests the sender's fax machine to send the data of the original.
1
Press the [FAX] button on the control panel.
2
Press the [ADVANCED] tab, and then press [POLLING].
3
If the password is set to the data of the original in the sender’s fax machine, press
[PASSWORD] to display the entry screen. Key in the password, and then press [OK].
If you do not have to key in the password, leave this entry box blank, and then press [OK].
4
Specify the sender’s fax number.
P.32 “Specifying the recipient”
This equipment supports two types of receptions: Individual polling reception in which you specify a recipient’s fax number and Multi-polling reception in which you specify multiple recipients’ fax numbers.
5
Press [SEND].
With the delayed transmission reservation, you can perform the polling reception on a specific date and time. To do that, set the date and time before pressing [SEND].
P.75 “Delayed Transmission Reservation”
60 Polling Communication
4 ADVANCED FUNCTIONS
Mailbox Transmission
This function is used to communicate between fax machines compatible with a mailbox function (ITU-T compatible). The owners of these fax machines can input or retrieve the data of the originals in the mailbox.
There are 3 types of mailbox: confidential mailbox, bulletin board mailbox and relay station mailbox. To perform mailbox communication, the mailboxes must be created in advance. An individual password for each box can be set for security protection.
P.69 “Creating/modifying/deleting a mailbox”
Confidential mailbox
Once data of an original are retrieved from this mailbox, these data will be deleted. This mailbox is suitable for registering an original you want to send to a specific recipient. If a new original is registered in this mailbox in which another original exists, the mailbox will contain both of the originals.
Bulletin board mailbox
No matter how many times an original is retrieved from this mailbox, the original will not be deleted. This mailbox is suitable for registering an original you want to send to multiple recipients. If a new original is registered in this mailbox in which another original exists, the existing original will be replaced with the new original and the new one will be stored in the mailbox.
Relay station mailbox
Using this mailbox, an original sent from a fax machine is relayed to pre-registered multiple recipients. To inform a user of the result of the relay, a report called RELAY TX END TERMINAL REPORT can be sent to a specific recipient. A copy of the original can be printed out (regularly or when an error occurs).
<Example of how to use the relay station mailbox>
If you want to send a copy of an original from an office in Los Angels to multiple offices in New York, you first send it from the one in Los Angels to one of the offices in New York where the relay station mailbox is set up, so that it is relayed to the other offices in New York. This will reduce communication costs.
NORMAL
LA office
(213)
NY office A
(212)
NY office B
(212)
NY office C
(212)
NY office D
(212)
* 4 long-distance calls
Relay Originator
Relay Station
Relay
Destination
VIA RELAY MAILBOX
LA office
(213)
NY office A
(Relay Mailbox)
(212)
NY office B
(local)
NY office C
(local)
NY office D
(local)
* 1 long-distance call to the NY office A
(relay mailbox) and 3 local calls between the NY office A (relay mailbox) and each office.
If you create a forward mailbox whose number is the fax number of the sender, you can use the TSI function. Using this function, this equipment forwards the original sent from the sender whose fax number is set to the mailbox number, based on the pre-set agent (Save as file / Email / Store to e-Filing). This can be set from TopAccess. For details of the operation, refer to the TopAccess Guide.
Mailbox Transmission 61
4 ADVANCED FUNCTIONS
Registering/printing/deleting an original
This section describes the operations of the mailbox in this equipment.
Registering an original
You can register an original to the confidential or bulletin board mailbox in this equipment.
To register the originals to confidential or bulletin board mailbox, the confidential or bulletin board mailbox must be created in advance.
P.69 “Creating/modifying/deleting a mailbox”
1
Place the original(s).
2
Press the [FAX] button on the control panel.
3
Press [OPTION] and set the transmission conditions.
P.28 “Setting the transmission conditions”
4
Press the [ADVANCED] tab, and then press [ITU MAILBOX].
5
In the “BOX TYPE” group, press [CONFIDENTIAL] or [BULLETIN BD]. In the “MODE” group, press [INPUT], and then [OK].
If the selected mailbox has not been set, an error message is displayed and you are unable to proceed.
62 Mailbox Transmission
4 ADVANCED FUNCTIONS
4.ADVANCED FUNCTIONS
6
Press [BOX NUMBER] to display the entry screen. Key in the box number, and then press [OK].
y If a password has been set to the selected bulletin board mailbox, key in the password in the same way as the box number. If you have selected the confidential mailbox, it is not necessary to key in a password since it is not verified.
y If the box number or password is incorrect, an error message is displayed and you are unable to proceed.
7
Press the [START] button on the control panel.
When you cancel the registration, press the [STOP] button on the control panel, and then [JOB CANCEL] on the touch panel.
Mailbox Transmission 63
4 ADVANCED FUNCTIONS
Printing an original
You can print the original registered in the confidential or bulletin board mailbox in this equipment.
1
Press the [FAX] button on the control panel.
2
Press the [ADVANCED] tab, and then press [ITU MAILBOX].
This screen is the same as the one you see when you register the original.
P.62 “Registering an original”
3
In the “BOX TYPE” group, press [CONFIDENTIAL] or [BULLETIN BD]. In the “MODE” group, press [PRINT], and then [OK].
If the selected mailbox has not been set, an error message is displayed and you are unable to proceed.
4
Press [BOX NUMBER] to display the entry screen and key in the box number.
If a password has been set to the selected confidential mailbox, key in the password in the same way as the box number. If you have selected the bulletin board mailbox, it is not necessary to key in a password since it is not verified.
5
Press the [START] button on the control panel.
If the box number or password is incorrect, an error message is displayed and you are unable to proceed.
64 Mailbox Transmission
4 ADVANCED FUNCTIONS
4.ADVANCED FUNCTIONS
Deleting an original
You can delete the original registered in the confidential or bulletin board mailbox in this equipment.
1
Press the [FAX] button on the control panel.
2
Press the [ADVANCED] tab, and then press [ITU MAILBOX].
This screen is the same as the one you see when you register the original.
P.62 “Registering an original”
3
In the “BOX TYPE” group, press [CONFIDENTIAL] or [BULLETIN BD]. In the “MODE” group, press [CANCEL], and then [OK].
If the selected mailbox has not been set, an error message is displayed and you are unable to proceed.
4
Press [BOX NUMBER] to display the entry screen. Key in the box number, and then press [OK].
If a password has been set to the selected mailbox, key in the password in the same way as the box number.
5
The confirmation screen for the deletion is displayed. Press [YES].
If the box number or password is incorrect, an error message is displayed and you are unable to proceed.
Mailbox Transmission 65
4 ADVANCED FUNCTIONS
Sending/retrieving an original
This section describes the operations of the mailbox in the recipient's fax machine.
Sending an original
You can send an original to the confidential/bulletin board/relay station mailbox in this equipment.
1
Place the original(s).
2
Press the [FAX] button on the control panel.
3
Press [OPTION] and set the transmission conditions.
P.28 “Setting the transmission conditions”
4
Press the [ADVANCED] tab, and then press [ITU MAILBOX].
5
In the “BOX TYPE” group, press [CONFIDENTIAL], [BULLETIN BD] or [RELAY]. In the
“MODE” group, press [TRANSMIT], and then [OK].
66 Mailbox Transmission
4 ADVANCED FUNCTIONS
4.ADVANCED FUNCTIONS
6
Press [BOX NUMBER] to display the entry screen. Key in the box number, and then press [OK].
If a password has been set to the selected mailbox, key in the password in the same way as the box number.
The box number and the password you specified here are sent to the recipient’s fax machine as SUD (box number) and SID (password) of the command compatible with the ITU-T standards.
7
Specify the recipient’s fax number.
P.32 “Specifying the recipient”
8
Press [SEND].
You can cancel the transmission of the original.
P.51 “Canceling the Transmission”
Retrieving an original
You can retrieve an original from the confidential or bulletin board mailbox in the recipient's fax machine.
1
Press the [FAX] button on the control panel.
2
Press the [ADVANCED] tab, and then press [ITU MAILBOX].
This screen is the same as the one you see when you send the original.
3
In the “BOX TYPE” group, press [CONFIDENTIAL] or [BULLETIN BD]. In the “MODE” group, press [POLLING], and then [OK].
Mailbox Transmission 67
4 ADVANCED FUNCTIONS
4
Press [BOX NUMBER] to display the entry screen. Key in the box number, and then press [OK].
If a password has been set to the selected mailbox, key in the password in the same way as the box number.
The box number and the password you specified here are sent to the recipient’s fax machine as SUD (box number) and SID (password) of the command compatible with the ITU-T standards.
5
Specify the recipient's fax number.
P.32 “Specifying the recipient”
6
Press [SEND].
68 Mailbox Transmission
4.ADVANCED FUNCTIONS
Creating/modifying/deleting a mailbox
This section describes how to manage the mailbox in this equipment.
In the list, you can view the status of the mailbox registered to this equipment.
P.86 “Mailbox/relay box report”
Creating the confidential or bulletin board mailbox
You can create the confidential or bulletin board mailbox in this equipment.
1
Press the [FAX] button on the control panel.
2
Press the [ADVANCED] tab, and then press [ITU MAILBOX].
4 ADVANCED FUNCTIONS
3
In the “BOX TYPE” group, press [CONFIDENTIAL] or [BULLETIN BD]. In the “MODE” group, press [BOX SETUP], and then [OK].
Mailbox Transmission 69
4 ADVANCED FUNCTIONS
4
Press [BOX NUMBER] to display the entry screen, key in the box number(s) (a maximum of 20 digits), and then press [OK].
y If you want to set a password (a maximum of 20 digits), key in the password in the same way as the box number.
y
If the box number or password keyed in has already been registered, an error message is displayed and you are unable to proceed.
Creating/modifying a relay station mailbox
You can create or modify the relay station mailbox.
1
Press the [FAX] button on the control panel.
2
Press the [ADVANCED] tab, and then press [ITU MAILBOX].
This screen is the same as the one you see when you create the confidential/bulletin board mailbox.
P.69 “Creating the confidential or bulletin board mailbox”
3
In the “BOX TYPE” group, press [RELAY]. In the “MODE” group, press [BOX SETUP] or
[MODIFY], and then [OK].
If the selected mailbox is not set at the time of modification, an error message is displayed and you are unable to proceed.
70 Mailbox Transmission
4 ADVANCED FUNCTIONS
4.ADVANCED FUNCTIONS
4
Press [BOX NUMBER] to display the entry screen. Key in the box number(s) (a maximum of 20 digits), and then press [OK].
y If you want to set a password (a maximum of 20 digits), key in the password in the same way as the box number.
y
If the box number or password is incorrect, an error message is displayed and you are unable to proceed.
5
Specify the recipient to be registered, and then press [OK].
P.32 “Specifying the recipient”
Specify the recipient from the address book because this cannot be done with direct dialing.
6
The confirmation screen for sending a relay transmission report is displayed. If you want to send the report, select [YES]. If not, select [NO].
By default, the relay transmission end terminal report is sent when a communication error occurs. On the
ADMIN menu, you can make setting so that the report can be sent automatically. For details of the operation, refer to the MFP Management Guide.
Mailbox Transmission 71
4 ADVANCED FUNCTIONS
7
Specify the recipient to which you want to send the report, and then press [OK].
P.32 “Specifying the recipient”
Only one recipient can be specified.
8
The confirmation screen for printing the received copy of the original is displayed. If you want to print it out whenever a copy of the original is delivered, press [ALWAYS]. If you want to print it out only when an error occurs, press the [ON ERROR].
Deleting a mailbox
You can delete the confidential/bulletin board/relay station mailbox registered in this equipment.
The confidential and bulletin board mailbox in which the original is registered cannot be deleted. To delete the mailbox, delete the original in advance.
1
Press the [FAX] button on the control panel.
2
Press the [ADVANCED] tab, and then press [ITU MAILBOX].
This screen is the same as the one you see when you create the confidential/bulletin board mailbox.
P.69 “Creating the confidential or bulletin board mailbox”
72 Mailbox Transmission
4 ADVANCED FUNCTIONS
4.ADVANCED FUNCTIONS
3
In the “BOX TYPE” group, press [CONFIDENTIAL], [BULLETIN BD] or [RELAY]. In the
“MODE” group, press [BOX DELETE], and then [OK].
If the selected mailbox has not been set, an error message is displayed and you are unable to proceed.
4
Press [BOX NUMBER] to display the entry screen. Key in the box number, and then press [OK].
If a password has been set to the selected mailbox, key in the password in the same way as the box number.
5
The confirmation screen for the deletion is displayed. Press [YES].
If the box number or password is incorrect, an error message is displayed and you are unable to proceed.
Mailbox Transmission 73
4 ADVANCED FUNCTIONS
Chain Dial Communication
You can chain pre-registered sets of numbers to form a dialing string. For example, you can form the desired number by specifying sets of numbers registered in the address book sequentially such as region code, area code and fax numbers.
1
Place the original(s).
2
Press the [FAX] button on the control panel.
3
Press [OPTION] and set the transmission conditions.
P.28 “Setting the transmission conditions”
4
Press the [ADVANCED] tab, and then press [CHAIN DIAL COMM.].
5
Repeat this operation until the desired number is formed.
P.32 “Specifying the recipient”
You can form the dialing number which is up to 128 digits in length. The numbers are chained in the order you specify them.
6
Press [SEND].
74 Chain Dial Communication
4 ADVANCED FUNCTIONS
Delayed Transmission Reservation
You can send a fax at a specified date and time. It is useful when you want to make use of off-peak discounts (e.g. nighttime) or you want to send a fax to a country which has a time difference.
1
Place the original(s).
2
Press the [FAX] button on the control panel.
3
Press [OPTION] and set the transmission conditions.
P.28 “Setting the transmission conditions”
4
Press the [ADVANCED] tab, and then press [DELAYED TX RESERVE].
5
Key in the date, hour, and minute using the digital keys on the control panel, and then press [OK].
y The acceptable range of reservation is up to one month later.
y Press and to move the cursor.
y Specify the time on a 24-hour basis.
y To correct the entry, press the [FUNCTION CLEAR] button on the control panel, and then key in the correct number.
6
Specify the recipient’s fax number.
P.32 “Specifying the recipient”
7
Press [SEND].
Canceling delayed transmission reservation
You can cancel the delayed transmission reservation and send a fax in a normal manner. On the reserved transmission confirmation screen, select the transmissions job, and then press [SEND].
P.48 “Checking reserved transmissions”
Delayed Transmission Reservation 75
4 ADVANCED FUNCTIONS
Recovery Transmission
You can save the data of originals, which were not sent after redialing a specified number of times, in the memory and resend them without placing the originals. Enabling or disabling this function or a period of time for the data to be retained can be set on the ADMIN menu. For the details of the current setting, ask your administrator.
P.108 “Setting recovery transmission”
1
Press the [FAX] button on the control panel.
2
Press [OPTION] and set the transmission conditions.
P.28 “Setting the transmission conditions”
3
Press the [ADVANCED] tab, and then press [RECOVERY TX].
4
Select the transmission job, and then press [SEND].
y
You can change the fax number which is specified with the direct entry method.
y To delete the selected transmission job, press [JOB CANCEL].
76 Recovery Transmission
4 ADVANCED FUNCTIONS
Onramp Gateway
The onramp gateway function allows for an original sent from another mailbox-supported fax machine to be converted into
E-mail data, which will be sent to a pre-registered E-mail address, via the mailbox (relay station) in this equipment.
ITU-T Compatible
G3 Fax machine
1. A fax is sent to the Relay Box of the equipment through the public telephone line.
Mail Server e-STUDIO
Relay Box
2. The fax is converted to an E-mail and sent to the E-mail address registered in the Relay Box.
Internet
Intranet
Mail Server
Internet Fax machine
3. The E-mail (Internet Fax) is received through the Network.
Mail Server Client Computer
3. The E-mail is received through the
Network.
Fax numbers and E-mail addresses can be registered to the mailbox used for an onramp gateway transmission. That mailbox is the same as the one used for the mailbox transmission. For details of how to create/modify/delete a relay station mailbox, see the following section.
P.69 “Creating/modifying/deleting a mailbox”
To use the onramp gateway, you need to set an E-mail address and Internet Fax to this equipment. For details of the operation, refer to the TopAccess Guide.
Onramp Gateway 77
4 ADVANCED FUNCTIONS
Offramp Gateway
The offramp gateway function allows for E-mail or Internet Fax sent from another device to be converted into standard fax data via this equipment, which will be sent to the recipient specified by the sender via a public telephone line. This is useful in reducing communication costs by using a combination of both the Internet and public telephone lines. For example, when sending documents long distances, such as overseas, the Internet can be used to send the document to a machine in the country of destination and then it will be forwarded to a target fax machine as fax data via a public telephone line.
1. The domain name of this equipment and the fax number of the final recipient are specified and an Internet
Fax is sent.
Internet Fax machine
Mail Server
2. The E-mail and the Internet
Fax in which the domain name of this equipment is specified are received, and are sent to this equipment.
3. The received E-mail and the Internet
Fax are converted to the standard fax, and are sent to the final recipient's fax machine.
e-STUDIO
Mail Server
(SMTP)
Internet
Intranet
Client Computer
Subaddress
Destination
G3 Fax machine
Mail Server
1. The domain name of this equipment and the fax number of the final recipient are specified and an E-mail is sent.
4. If a subaddress is specified in the recipient of the received fax, the fax is sent to the subaddress destination.
Specifying an E-mail address
When you want to use this equipment as a relay station to perform an offramp gateway transmission, ask the sender to specify an E-mail address as follows.
y FAX=xxxxxxxx@FQDN
The fax number of the final recipient is specified in “xxxxxxxx”.
e.g.: In case that the fax number is “1234567890” and the domain name of this equipment (FQDN) is
“host1.toshibatec-ifax.com”, the fax should be sent to
Sending to a subaddress y
FAX=xxxxxxxx/T33S=yyyy@FQDN
The fax number of the final recipient is specified in “xxxxxxxx” and the subaddress in “yyyy”.
e.g.: In case that the fax number is “1234567890”, the subaddress is “1234”, and the domain name of this equipment
(FQDN) is “host1.toshibatec-ifax.com”, the fax should be sent to
FAX=1234567890/[email protected]
Setting up the SMTP server
SMTP is a server protocol for sending and receiving E-mails. To use the offramp gateway function, you need to set up the
SMTP server so that this equipment can receive E-mails and Internet Fax using SMTP. For details of the operation, refer to the TopAccess Guide.
78 Offramp Gateway
4 ADVANCED FUNCTIONS
Save as File
While sending a fax, you can save the fax as a file to a shared folder in this equipment or in a client computer. That file can be accessed from client computers on a network. To save a fax as a file into a shared folder in a client computer, you must make the “Save as file” setting of this equipment in advance. For details of the operation, refer to the TopAccess Guide.
y Be sure to back up the files in the shared folder to protect them from unexpected data loss events.
y If the forced encryption function for PDF security
*
is enabled, this function is not available. For the details of the security settings, refer to the MFP Management Guide.
* The PDF security may not be available depending on the equipment.
1
Place the original(s).
2
Press the [FAX] button on the control panel.
3
Press [STORAGE].
4
Press [FILE NAME], and then enter the file name (a maximum of 45 characters).
If you press [FILE NAME], the on-screen keyboard appears. For details of the operation to enter characters, refer to the Quick Start Guide.
Save as File 79
4 ADVANCED FUNCTIONS
5
Select the location where you want to save the file and the file format, and then press
[OK].
y
When PDF-MULTI, TIFF-MULTI, or XPS-MULTI is selected, the file should be saved as a multiple-page file.
When PDF-SINGLE, TIFF-SINGLE, or XPS-SINGLE is selected, the file should be saved as a single-page file.
y Select the file format in the [FILE FORMAT] box.
When a file is saved in the shared folder of the hard disk in this equipment, it is saved in the “TXFAX” folder under the “FILE_SHARE” folder. When PDF-SINGLE, TIFF-SINGLE, or XPS-SINGLE is selected, another folder with the same file name is automatically created in the “TXFAX” folder in which the file is saved.
6
Specify the recipient's fax number.
P.32 “Specifying the recipient”
7
Press [SEND].
When fax transmission is completed, storing of the data of the original is also completed. However, if a fax cannot be sent after redialing a specified number of times, only the storing of the data of the original is completed.
80 Save as File
4 ADVANCED FUNCTIONS
Printing SECURE RECEIVE fax jobs
When the PRINT DATA lamp on the control panel is lit, there is a received SECURE RECEIVE fax job.
You can print the fax data by entering your PRINT PASSWORD.
This lamp does not light when the equipment is in the Super Sleep mode.
1
Press the [PRINT] button on the control panel.
y The print screen is displayed. If you leave the screen unattended for the auto clear setting time (45 sec by manufacture default), the screen returns to the default one automatically.
2
Select [SECURE RX (LINE 1)] or [SECURE RX (LINE 2)] in the pull-down menu.
y If the equipment is running in the High Security mode, [SECURE RX (LINE 1)] and [SECURE RX (LINE 2)] are not displayed.
3
Select the desired fax job on the touch panel, and then press [PRINT].
y You can select and print multiple fax jobs at once.
Printing SECURE RECEIVE fax jobs 81
4 ADVANCED FUNCTIONS
4
Press [PASSWORD].
5
Enter the password for printing a received SECURE RECEIVE fax, and then press [OK] to start printing.
y Use the password set by your administrator for each line.
82 Printing SECURE RECEIVE fax jobs
5.
PRINTING LISTS AND REPORTS
This chapter explains how to print lists and reports.
5 PRINTING LISTS AND REPORTS
Printing Lists & Reports Manually
You can print lists and reports (journals) manually. For samples of lists and reports, see the following section.
y Lists and reports are printed on LT/A4-size paper. If this equipment has run out of LT/A4-size paper, lists and reports will be printed on larger sized paper.
y
In addition to the lists described in this section, the following lists can be printed manually: For details of the operation, refer to the MFP Management Guide.
ADDRESS BOOK INFORMATION: List of recipients registered in the address book.
GROUP NUMBER INFORMATION: List of recipients registered in the address book as a group.
FUNCTION LIST: List of the user settings.
Journal (transmission journal/reception journal)
You can print a list of transmissions and receptions.
This equipment logs up to the latest 40 or 120 transmission/reception records. This number can be set on the ADMIN menu. For details of the operation, refer to the MFP Management Guide.
1
Press [JOB STATUS].
2
Select the [LOG] tab, and then press [SEND] or [RECEIVE].
84 Printing Lists & Reports Manually
5 PRINTING LISTS AND REPORTS
5.PRINTING LISTS AND REPORTS
3
Press [JOURNAL].
If [JOURNAL] is pressed with the transmission/reception records selected, the journal of the selected file is printed.
Reservation list
You can print a list of the reserved transmissions.
1
Press [JOB STATUS].
2
Press the [FAX], and then press [RESERVATION LIST].
Printing Lists & Reports Manually 85
5 PRINTING LISTS AND REPORTS
Mailbox/relay box report
You can print a list of the current status of the mailboxes registered to this equipment.
1
Press the [FAX] button on the control panel.
2
Press the [ADVANCED] tab, and then press [ITU MAILBOX LIST].
86 Printing Lists & Reports Manually
5 PRINTING LISTS AND REPORTS
Printing Lists & Reports Automatically
You can print lists and reports automatically. For samples of lists and reports, see the following section.
Lists and reports are automatically printed according to the settings that the administrator made, so no user operation is required. For details of the setting operation, refer to the MFP Management Guide.
The available lists/reports to be printed automatically are as follows:
TRANSMISSION JOURNAL
When this equipment completes 40 or 120 transmission jobs, the transmission journal is printed.
RECEPTION JOURNAL
When this equipment completes 40 or 120 reception jobs, the reception journal is printed.
MEMORY TRANSMISSION REPORT
When the memory transmission is completed, the report is printed. (You have an option to add a reduced image of the transmitted document.)
TRANSMISSION REPORT
When the direct transmission is completed, the report is printed.
MULTI TRANSMISSION REPORT
When the multi-address transmission is completed, the report is printed. (You have an option to add a reduced image of the transmitted document.)
MULTI POLLING REPORT
When a multi-polling RX is completed, the report is printed.
RELAY TX ORIG. TERMINAL REPORT
When the document transmission from an originator terminal to a relay station is completed during the mailbox transmissions, the report is printed. (You have an option to add a reduced image of the transmitted document.)
RELAY TX RELAY STATION REPORT
When a document transmission from a relay station to an end terminal is completed during the mailbox transmissions, the report is printed. (You have an option to add a reduced image of the transmitted document.)
RELAY TX END TERMINAL REPORT
When the document transmission from a relay station to an end terminal is completed during the mailbox transmissions, the report is sent to an originator terminal. (You have an option to add a reduced image of the transmitted document.)
RELAY STATION REPORT
When a relay station in this equipment receives an original during the mailbox transmissions, the report is printed.
MAILBOX RECEPTION REPORT
When the confidential or bulletin board mailbox in this equipment receives an original during the mailbox receptions, the report is printed.
Printing Lists & Reports Automatically 87
5 PRINTING LISTS AND REPORTS
Lists/Reports Samples
Transmission journal
ROM version
Terminal ID
Sender’s Fax number
(Line2: Optional)
Sender’s Fax number
(Line1)
Journal (or list) outputting date and time
NO.
001
002
TRANSMISSION JOURNAL
FILE NO.
002
010
DATE TIME
05.10 16:59
05.10 17:33
DURATION PGS
00:23
00:00
1
0
XXXXXXXXXXX
TIME
FAX NO.1
FAX NO.2
NAME
TO
Redfield HS
2123456789
XXXX-XXX
: 05-10-2011 17:55
: 2131234567
: 2131235678
: Aaabbb L.A.
DEPT MODE
EC 603
STATUS
OK
P 00B5
Serial number for communication
Date and time when starting communication
The number of pages for the communication
Department code
(blank if not controlled with department code)
File number of communication
Communicating period of time
Communication mode
EC: ECM communication
G3: G3 communication
ML: Email communication
1 st
(bps)
2
3
0
1
4
5
6
8
B
D
2,400
4,800
7,200
9,600
12,000
14,400
V.34
2 nd
(Resolution)
3 rd
(Mode)
8 x 3.85
8 x 7.7
8 x 15.4
MH
MR
MMR
JBIG
16 x 15.4
300 dpi
600 dpi
150 dpi
Fax name or telephone number
Special communication mode
SR,R: Relay mailbox communication
SF,F: Forward mailbox communication
ML: Internet Fax communication
O: Offramp Gateway communication
Communication result and error code
OK: Succeeded
4-digit error code: Failed y The mark in the “TO” column indicates that the 2ND FAX registered in the address book is used.
y The mark in the “MODE” column indicates that the 2nd line is used.
y For error codes in the “STATUS” column, see the following section.
88 Lists/Reports Samples
5 PRINTING LISTS AND REPORTS
5.PRINTING LISTS AND REPORTS
Reception journal
NO.
001
002
RECEPTION JOURNAL
FILE NO.
003
007
DATE TIME
05.10 14:23
05.10 17:20
XXXXXXXXXXX
TIME
FAX NO.1
FAX NO.2
NAME
DURATION PGS
00:00
00:32
0
1
FROM
Aaabbb USA HQ
3109998888
XXXX-XXX
: 05-10-2011 17:55
: 2131234567
: 2131235678
: Aaabbb L.A.
DEPT MODE
EC 603
STATUS
NG 00B1
OK y What is included in this journal is the same as in the transmission journal.
y
For error codes in the “STATUS” column, see the following section.
Reservation list
RESERVATION LIST
TX / RX
FILE NO.
017
DATE TIME
05.10 18:41
RECOVERY TX
FILE NO.
013
DATE TIME
05.10 18:01
PC JOB
FILE NO.
003
DATE TIME
05.10 17:40
FUNCTION
MULTI TX
FUNCTION
MULTI TX
FUNCTION
MULTI TX
PGS
1
PGS
1
TIME
FAX NO.1
FAX NO.2
NAME
: 05-10-2011 18:41
: 2131234567
: 2131235678
: Aaabbb L.A.
DELAY TIME TO
G ABC EXPRESS
TO
2153334444
PGS
2
TO
Cccddd CORPORATION
DELAY TIME y The mark in the “TO” column indicates that the recipient is specified with the direct entry method.
y The mark G in the “TO” column indicates that the recipient is specified with the group entry method.
Lists/Reports Samples 89
5 PRINTING LISTS AND REPORTS
Mailbox/relay box report
MAILBOX/RELAY BOX REPORT
TIME
FAX NO.1
FAX NO.2
NAME
: 05-10-2011 18:00
: 2131234567
: 2131235678
: Aaabbb L.A.
MAIL BOX
BOX NO.
11222
BOX TYPE
BULLETIN BD
RELAY
BOX NO.
12345
END STATION
ADDRESS
GROUP
FORWARD/INBOUND FAX(TSI)
BOX NO. AGENT
22222 E-MAIL
PGS FILE NO. DATE TIME FROM
001 002 003 004 005
001 002
DESTINATION
To: ADDRESS: 001
GROUP : 001
Cc: ADDRESS: 002 003
GROUP : 002
REPLY TO NUMBER
12345
"END STATION" field indicates an E-mail address by a 4-digit number and the ID of a group by a 3-digit number.
90 Lists/Reports Samples
5 PRINTING LISTS AND REPORTS
5.PRINTING LISTS AND REPORTS
Memory transmission report
MEMORY TRANSMISSION REPORT
FILE NO. : 004
DOCUMENT PAGES
START TIME
END TIME
PAGES SENT
: 1
: 05.10 17:13
: 05.10 17:14 (STORED TIME : 05.10 23:14)
: 0
*** TX FAILURE NOTICE ***
TIME
FAX NO.1
FAX NO.2
NAME
: 05-10-2011 17:48
: 2131234567
: 2131235678
: Aaabbb L.A.
FILE NO. : 005 (ITU MAILBOX : 12345 )
DOCUMENT PAGES
START TIME
END TIME
PAGES SENT
: 1
: 05.10 17:30
: 05.10 17:31 (STORED TIME : 05.10 23:31)
: 1 y The mark in the “TO” column indicates that the 2ND FAX registered in the address book is used.
y The mark in the “TO” column indicates that the recipient is specified with the direct entry method.
y For error codes in the “STATUS” column, see the following section.
Lists/Reports Samples 91
5 PRINTING LISTS AND REPORTS
Transmission report
NO.
002
TRANSMISSION REPORT
FILE NO.
007
DATE TIME
05.10 17:20
XXXXXXXXXXX
TIME
FAX NO.1
FAX NO.2
NAME
DURATION PGS
00:32 1
TO
3109998888
XXXX-XXX
: 05-10-2011 17:55
: 2131234567
: 2131235678
: Aaabbb L.A.
DEPT MODE
EC 603
STATUS
OK
For the error codes displayed in the “STATUS” column, see the following section.
Multi transmission report
MULTI TRANSMISSION REPORT
TIME
FAX NO.1
FAX NO.2
NAME
FILE NO. : 013
DOCUMENT PAGES
START TIME
END TIME
SUCCESSFUL
ADDRESS BOOK
001
: 1
: 05.10 18:01
: 05.10 18:17 (STORED TIME : 05.11 00:17)
Aaabbb ADMIN
UNSUCCESSFUL
FAX NUMBER
3109998888
PAGES SENT
0
: 05-10-2011 18:17
: 2131234567
: 2131235678
: Aaabbb L.A.
y The mark in the “ADDRESS BOOK” column indicates that the 2ND FAX registered in the address book is used.
y The mark in the “FAX NUMBER” column indicates that the recipient is specified with the direct entry method.
92 Lists/Reports Samples
5 PRINTING LISTS AND REPORTS
5.PRINTING LISTS AND REPORTS
Multi polling report
MULTI POLLING REPORT
FILE NO.
START TIME
END TIME
SUCCESSFUL
ADDRESS BOOK
UNSUCCESSFUL
FAX NUMBER
2139998888
: 014
: 05.10 18:17
: 05.10 18:18
TIME
FAX NO.1
FAX NO.2
NAME
: 05-10-2011 18:18
: 2131234567
: 2131235678
: Aaabbb L.A.
The mark in the “FAX NUMBER” column indicates that the recipient is specified with the direct entry method.
Relay TX orig. terminal report
RELAY TX ORIG. TERMINAL REPORT
TIME
FAX NO.1
FAX NO.2
NAME
: 05-10-2011 18:22
: 2131234567
: 2131235678
: Aaabbb L.A.
FILE NO. : 016
RELAY BOX
DOCUMENT PAGES
START TIME
END TIME
PAGES SENT
: 12345
: 1
: 05.10 18:22
: 05.10 18:22
: 1
The mark in the “TO” column indicates that the recipient is specified with the direct entry method.
Lists/Reports Samples 93
5 PRINTING LISTS AND REPORTS
Relay TX relay station report
RELAY TX RELAY STATION REPORT
TIME
FAX NO.1
FAX NO.2
NAME
: 05-10-2011 14:46
: 2131234567
: 2131235678
: Aaabbb L.A.
FILE NO.
DOCUMENT PAGES
: 013
: 3
START TIME
END TIME
RELAY BOX
SUCCESSFUL
GROUP NUMBER
002 USA 1
: 05.10 14:45
: 05.10 14:46
: 12345
ADDRESS BOOK 001
UNSUCCESSFUL
ADDRESS BOOK
001 Cccddd ADMIN
PAGE SENT
0
The mark in the “ADDRESS BOOK” column is appended when the 2ND FAX registered in the address book is used for transmission.
Relay TX end terminal report
RELAY TX END TERMINAL REPORT
TIME
FAX NO.1
FAX NO.2
NAME
: 05-10-2011 14:46
: 2131234567
: 2131235678
: Aaabbb L.A.
FILE NO.
DOCUMENT PAGES
: 013
: 3
START TIME
END TIME
RELAY BOX
SUCCESSFUL
: 05.10 14:45
: 05.10 14:46
: 12345
ADDRESS BOOK
005 XYZ
UNSUCCESSFUL
ADDRESS BOOK
001 Cccddd
PAGES SENT
0
94 Lists/Reports Samples
5 PRINTING LISTS AND REPORTS
5.PRINTING LISTS AND REPORTS
Relay station report
RELAY STATION REPORT
TIME
FAX NO.1
NAME
: 05-10-2011 13:33
: 2131234567
: Aaabbb L.A.
FILE NO.
RELAY BOX
DOCUMENT PAGES
: 734
: 777
: 1
Mailbox reception report
MAILBOX RECEPTION REPORT
FILE NO.
BOX NUMBER
BOX TYPE
DOCUMENT PAGES
: 016
: 12345
: CONFIDENTIAL
: 1 (TOTAL 2 )
TIME
FAX NO.1
FAX NO.2
NAME
: 05-10-2011 18:22
: 2131234567
: 2131235678
: Aaabbb L.A.
Lists/Reports Samples 95
6.
SETTING ITEMS
This chapter describes the user and administrator settings related to the fax function.
6 SETTING ITEMS
User Settings
Fax settings
Set the initial settings for the fax transmission functions.
1
Press the [USER FUNCTIONS] button on the control panel.
2
Press [FAX].
98 User Settings
6.SETTING ITEMS
3
Set each setting item, and then press [OK].
6 SETTING ITEMS
Press or to switch the pages.
RESOLUTION
Set the resolution based on the fineness of the original.
STANDARD: This is suitable for an original with regular size text.
FINE: This is suitable for an original with small size text and detailed illustrations.
U-FINE: This is suitable for an original with ultra-detailed illustrations.
If the recipient’s fax machine is not capable of receiving originals at the same resolution, the resolution is automatically converted before being sent it to the recipient. The higher the resolution is, the longer it takes to send an original.
ORIGINAL MODE
Set the scanning mode based on the type of the original.
TEXT: This is suitable for an original with text and line drawings.
TEXT/PHOTO: This is suitable for an original with a mixture of text and photos.
PHOTO: This is suitable for an original with photos.
y In the TEXT/PHOTO mode or PHOTO mode, transmission time may be longer than in the TEXT mode.
y To scan originals printed with erasable toner, select TEXT mode.
TX TYPE
Set the fax transmission mode.
MEMORY TX: Send the original after the scanned data are saved in the memory. Up to 100 transmissions can be reserved. Up to 1000 pages can be sent in one transmission.
DIRECT TX: Send the original directly as it is being scanned. Once a page has been scanned and sent, the next page is scanned and sent. Therefore, it takes longer to scan and send all pages. However, you can confirm on the fly that each page is sent to the recipient.
User Settings 99
6 SETTING ITEMS
EXPOSURE
Set the density at which the original is to be scanned.
AUTO: This equipment automatically detects the contrast of the original, and scans it with the optimum contrast.
MANUAL: Press to
TTI
Switch the TTI recording ON or OFF. To enable this feature, the Terminal ID must be registered to this equipment in advance.
P.103 “Registering the terminal ID”
Setting this item may not be required since it may not be displayed on the screen (it depends on your country or region).
RTI
Switch the RTI recording ON or OFF. To enable this feature, the Terminal ID must be registered to this equipment in advance.
P.103 “Registering the terminal ID”
ECM
Switch the ECM (Error Correction Mode) communication ON or OFF.
ECM is an internationally standardized communication mode that automatically corrects errors that occur during fax transmissions. With this setting option ON, even when the transmitted data have been affected by noise during communication, this mode allows good communication without image distortion by automatically resending the part that have been affected.
y Both the sender and the receiver must have the ECM function to make ECM communication available.
y When affected by noise during communication, communication time is slightly longer than usual. Even when the ECM communication is used, an error may occur depending on the line status.
y The ECM communication is not available for voice communication.
PREVIEW SETTING (e-STUDIO4540C Series and e-STUDIO6550C Series)
Switch the preview setting ON or OFF.
INITIAL PREVIEW TYPE (e-STUDIO4540C Series and e-STUDIO6550C Series)
Set the preview type to be displayed as an initial
SECURE RECEIVE FORCED SETTING
You can enable or disable the SECURE RECEIVE function.
This is available only when the WEEKLY SCHEDULE function is set.
ON: This enables the SECURE RECEIVE function.
It becomes disabled at the time set by WEEKLY SCHEDULE.
OFF: This disables the SECURE RECEIVE function.
y It becomes enabled at the time set by WEEKLY SCHEDULE.
y An administrator password is required.
100 User Settings
Administrator Settings
This section describes the FAX menu managed by the administrator.
Follow the procedures below to display the menu you want to operate.
1
Press the [USER FUNCTIONS] button on the control panel.
6 SETTING ITEMS
2
Press [ADMIN] tab, and then press [PASSWORD].
3
Enter the administrator password, and then press [OK].
Administrator Settings 101
6 SETTING ITEMS
4
Press [FAX].
The FAX menu is displayed.
The following section describes each menu.
102 Administrator Settings
6 SETTING ITEMS
6.SETTING ITEMS
Registering the terminal ID
This section describes how to register the terminal ID of this equipment. If the terminal ID is registered in advance, sender information can be printed on the leading edge on the transmitted original, and receiver information on the trailing edge on the received fax.
1
Press [TERMINAL ID].
2
Set each setting option, and then press [OK].
y
You can enter up to 20 characters in the ID NAME, but whether they can all be displayed or not depends on their size.
y
When you add an international code, press [+]. To enter a pause “ - ”, press [Pause].
y [LINE2 NUMBER] is displayed only when the 2nd Line for FAX Unit (optional) is installed.
Administrator Settings 103
6 SETTING ITEMS
Example of how sender information is printed on paper
Sender information is printed about 5 mm (0.2 inch) from the top edge of the transmitted copy of the original.
05-10-2011 15:08 FROM-Aaabbb 1234567890 T-069 P0001/0001 F-049
File number
Date sent
(automatically attached)
Sender's ID name Sender’s ID (Fax) number
Number of pages
Pages sent/Total pages
Communication number
Example of how receiver information is printed on originals you receive
Receiver information is printed about 5 mm (0.2 inch) from the bottom edge of the received copy of the original.
RECEIVED 05-10-2011 15:08 FROM-Cccddd TO-Aaabbb
Date received
(automatically attached)
Remote Fax ID information
Setting the initial setup
You can set the initial settings for the fax functions.
1
Press [INITIAL SETUP].
Receiver’s
ID name
P0001/0001
Number of pages
Pages sent
104 Administrator Settings
6.SETTING ITEMS
2
Set each option, and then press [OK].
6 SETTING ITEMS
Press or to switch the pages.
RX MODE
Set the fax reception mode.
AUTO: This equipment receives an incoming fax automatically.
MANUAL: This equipment receives an incoming fax manually.
y To receive a fax in the manual mode, an external telephone is required.
y When the 2nd Line for FAX Unit (option) is installed, the reception mode of the 2nd lines limited to “AUTO reception”.
MONITOR VOLUME / COMPLETION TONE VOLUME
Monitor tone volume (line tone when on-hook) and Reception completion tone volume (You hear this tone when reception is completed). Each volume can be set in 8 levels (0: tone Off).
DIAL TYPE / DIAL TYPE (LINE2)
There are 2 types of telephone lines. When you first install this equipment or you change the connected telephone line, set this according to the telephone line type.
DP: Dial pulse lines.
MF: Multi frequency lines.
y Setting these items may not be required since they may not be displayed on the screen (it depends on your country or region).
y “DIAL TYPE (LINE2)” can be set when the 2nd Line for FAX Unit (optional) is installed.
Administrator Settings 105
6 SETTING ITEMS
Setting RX printing
You can set up options to print a received fax.
In the Administrator’s Function List, you can view the status of the options. For details of the operation to print the list, refer to the MFP Management Guide.
1
Press [RX PRINT].
2
Set each option, and then press [OK].
DISCARD
You can switch discard printing ON or OFF. With it being set to ON, if an original is up to 10 mm (0.4 inch) longer than the printing area, the part that exceeds the paper printing area is discarded.
P.44 “Default setting for RX printing”
106 Administrator Settings
6 SETTING ITEMS
6.SETTING ITEMS
DUPLEX PRINT
You can switch duplex printing ON or OFF. With it being set to ON, received documents are printed on both sides of paper.
y
Duplex printing is available only if the received fax sizes and resolution are the same.
y When paper has run out during duplex printing, the rest of the documents are printed on another size paper.
y When the received fax is printed on 2 sheets of paper because it exceeds the printing area, duplex printing is not available.
y Documents received using the batch transmission function are printed on both sides of the paper as one continuous document. Pay attention to the separation of the individual documents particularly those consisting of an odd number of pages.
y Even when duplex printing is set to ON, the document printed using the reception forward function is printed on a single side of paper.
y Duplex printing direction differs depending on the received document size, as shown in the figures below.
Received LD, LG, LT, A3, A4, or B4-sized documents are printed so that they can be bound along the long edge of the direction. (Figure 1)
Received ST, A5 or B5-sized documents are printed so that they can be bound along the short edge of the direction. (Figure 2)
1 2
A
A
REDUCTION
You can switch RX reduction printing ON or OFF. With it being set to ON, if an original exceeds the printing area by more than 10 mm (0.4 inch), it is reduced by 90% of the original size when printing.
P.44 “Default setting for RX printing”
ROTATE SORT
You can switch the rotate sort function ON or OFF. With this being set to ON, received faxes are alternately sorted horizontally and vertically for each fax job.
y Rotate Sort is available only for LT/A4-sized paper. Set the LT and LT-R, or A4 and A4-R drawers.
y
If paper runs out during Rotate Sort, the rest of the documents are printed on the remaining paper. If no copy paper remains, printing is performed on a larger size than A4/A4-R or LT/LT-R.
y When the rotate sort function is set to ON, the attribute cannot be set to “FAX”.
Administrator Settings 107
6 SETTING ITEMS
Setting recovery transmission
You can set a period of time to retain original data in the memory for the recovery transmission function, or whether enabling or disabling this function.
1
Press [RECOVERY TX].
2
Press [ 24H] or [ 1H] to set the document-stored time, and then press [OK].
When the screen is returned to the one shown in step 1 above, make sure that an orange line is marked on
[RECOVERY TX]. This line indicates that the recovery transmission function is ON. If you press [RECOVERY
TX] again, the orange line disappears, that is, the function is OFF.
108 Administrator Settings
6 SETTING ITEMS
6.SETTING ITEMS
Setting 2nd Line for FAX Unit
You can make settings so that two lines can be used at the same time using the 2nd Line for FAX Unit (optional) installed.
In addition to the settings described below, you need to: y Register the terminal ID.
P.103 “Registering the terminal ID”
y Set the dial type.
P.104 “Setting the initial setup”
1
Press [LINE-2 MODE].
2
Set how you want to use the 2nd line, and then press [OK].
TX / RX
The 2nd line is used for both transmission and reception.
RX ONLY (24HR)
The 2nd line is used only for reception.
RX ONLY (TIMER)
The 2nd line is used only for reception during a specified period of time. To move the cursor, use or .
Specify the time period on a 24-hour basis using the digital keys on the control panel.
The automatic reception is only available for the 2nd line.
Administrator Settings 109
6 SETTING ITEMS
SECURE RECEIVE
The SECURE RECEIVE function allows you to store received fax jobs in the equipment without printing them. With this function, you can prevent the leaking of confidential information in a fax received when no people are present in your office, such as nighttime or holidays, or when an unspecified number of people visit your office.
The SECURE RECEIVE setting consists of a manual ON/OFF setting and a scheduled ON/OFF setting for each day of the week (WEEKLY SCHEDULE) by administrators.
The SECURE RECEIVE function can be manually enabled/disabled, or automatically enabled/disabled at a specified time and day of the week.
y If the equipment is being used in the High Security mode, the SECURE RECEIVE function is not available.
y The data lamp does not light when the equipment is in the Super Sleep mode.
In [FAX] in the [USER] tab, you can enable or disable the SECURE RECEIVE function earlier than the time set by
WEEKLY SCHEDULE.
Setting SECURE RECEIVE
You can set how you receive a SECURE RECEIVE fax.
1
Press [SECURE RECEIVE].
2
Select [WEEKLY SCHEDULE] or [ENABLE] for SECURE RECEIVE.
[ENABLE]
You can enable the SECURE RECEIVE function.
110 Administrator Settings
6 SETTING ITEMS
6.SETTING ITEMS
[WEEKLY SCHEDULE]
You can set the time for each day of the week for automatically enabling or disabling the SECURE RECEIVE function.
y Time is displayed in 24-hour format.
y To enable the function throughout the day, set [DISABLE]/[ENABLE] to 00:00/00:00.
y
To disable the function throughout the day, set [DISABLE]/[ENABLE] to 00:00/24:00.
To clear the entered time, press the [Clear] button on the control panel.
Setting a password for printing
You can set a password for printing a received SECURE RECEIVE fax.
1
Select [LINE 1] or [LINE 2].
y A password for printing can be set for each line.
2
Press [NEW PASSWORD].
Administrator Settings 111
6 SETTING ITEMS
3
Enter the password and press [OK].
4
Press [RETYPE NEW PASSWORD], enter the same password again, and then press
[OK].
y Up to 20 alphanumeric characters (including the following symbols) can be entered for the passward.
You can use alphanumerics and the following symbols.
# $ ( ) * + , - . / : ; = ? @ \ ^ _ ` { | } ~
5
Press [OK].
It can be set also on the TopAccess menu.
112 Administrator Settings
7.
TROUBLESHOOTING AND
SPECIFICATIONS
This chapter describes troubleshooting and specifications of GD-1250/GD-1270.
7 TROUBLESHOOTING AND SPECIFICATIONS
Troubleshooting
Error codes
Below is a list of error codes that you might see in the lists or reports.
Error Code
0012
0013
0020
0030
0033
0042
0050
0053
00B0 - 00E8
Description
Original jam
Door open
Power interruption
Reset
Polling Error
Memory full
Line busy
Security mismatch in relay or mail box transmission
Communication Error
Remedy
Clear the jammed original.
Firmly close the open door.
Check the power interruption report.
Transmission is cancelled.
(The transmission is terminated by the jammed printing paper during the direct transmission.)
Check polling options setup (Security code, etc.), and check if the polling document exists.
Make sure that there is sufficient memory before making the call again.
Retry communications.
Confirm the remote party’s security code, system password, and your setup.
Retry communications.
If you see an error code not listed here, retry the communication. If this error still occurs, contact your service technician or service representative.
Error messages
Below is a list of error messages that might appear on the touch panel. When any message in the list appears on the touch panel, press [FUNCTION CLEAR] on the control panel to clear it, and then take action suggested in the “Remedy” column.
Message
Memory overflow
Communication error
Job reservation full
Job memory full
Sorry not possible
Not allowed now
Too Many Tel # Digits
Cause
Memory overflowed when scanning documents to the memory.
Communication error occurred during direct TX.
The number of reserved jobs exceeded 100.
The total number of destinations for reserved jobs exceeded 2000.
On-hook or direct TX was attempted during communications.
Further polling transmission reservation was attempted even though polling transmission was already reserved.
128 digits or more were registered for a chain dial communication.
Remedy
Either wait for memory to be cleared, or check the jobs and delete reserved jobs to clear memory.
Retry communications.
Either wait for job reservations to be completed, or check the jobs and delete reserved jobs.
Either wait for job reservations to be completed, or check the jobs and delete reserved jobs.
Wait for communications to end and retry communications.
Either wait for polling transmission jobs to be completed, or check the jobs and delete reserved jobs.
Confirm the number of digits dialed and register the numbers again.
Never attempt to repair, disassemble or modify the equipment by yourself.
You could cause a fire or get an electric shock. Always contact your service representative for maintenance or repair of the internal parts of the equipment.
For error messages not listed above and their solutions, refer to the Troubleshooting Guide.
114 Troubleshooting
7 TROUBLESHOOTING AND SPECIFICATIONS
7.TROUBLESHOOTING AND SPECIFICATIONS
Transmission/reception trouble
Below is a list of trouble you might encounter during the transmission/reception.
Transmission troubles
Trouble
TRANSMIT is not displayed even if the
[START] button is pressed.
Originals are fed diagonally.
2 originals are fed together.
Check Point
y
Did you replace the handset before you pressed the [START] button? When you are making a call on the handset to send a Fax, do not replace the handset until you press the [START] button.
y
Is the modular cord disconnected?
y Is the power plug unplugged from the power outlet?
y Can you receive telephone calls?
y Is there any problem at the remote Fax? Check this with the party trying to receive the original.
y Are the document feeder slides adjusted to the width of the original that you are sending?
y Does the original that you are sending match the conditions of the original that is available for sending?
y Have you placed more than the maximum number of originals that can be placed at one time? y Does the original that you are sending match the conditions of the original that is available for sending?
y Have you pushed the originals into the feeder too hard?
Was the original placed correctly facing up?
The original is not being printed on the paper of the remote Fax even though it has been sent.
Black lines are shown in the image that was sent.
Originals are not sent even if operations are carried out normally.
Originals cannot be sent overseas.
Is the scanning area of the Reversing Automatic Document Feeder clean?
Clean it with a soft cloth.
Is the remote Fax compatible with your system?
This system supports G3 communications but not G2 or G4 communications.
Specify Quality TX and resend.
P.28 “Setting the transmission conditions”
Reception troubles
Originals cannot be received even if
“RECEIVE” is displayed and the [START] button is pressed.
Paper is not output.
The received original is printed dark and is illegible or black stripes are printed on the original.
Paper is output but not printed.
Paper often jams.
y Did you replace the handset before you pressed the [START] button? When you answer a call on the handset to receive a Fax, do not replace the handset until you press the [START] button.
y Is the modular cord disconnected?
y Is there a problem at the remote Fax? Check this with the party trying to send the original.
Is the equipment out of paper?
y Make a local copy and confirm proper printing.
y Is the original being sent a dirty copy? Check this with the party trying to send the original.
y Is the trouble due to a problem or operation error at the remote Fax? Check this with the party trying to send the original.
y Is there enough toner?
y Is the original placed correctly on the remote Fax? Check this with the party trying to send the original.
y Is the paper drawer size setting correct?
y Is the paper drawer properly inserted?
y Is the specified paper type being use?
If the suggested action does not solve the trouble or you encounter trouble not listed above, contact your service technician or service representative.
Troubleshooting 115
7 TROUBLESHOOTING AND SPECIFICATIONS
Specifications of GD-1250/GD-1270
Model Name GD-1250 (For FC-2040C/2540C/3040C/3540C/4540C, DP-2095/2530/3020/3590/4590, DP-5560/6560/
7560/8560 and DP-3030)
GD-1270 (For FC-5540C/6540C/6550C)
LD, LG, LT, LT-R, ST, ST-R, COMP Size of Original
(North America)
Size of Original
(A/B format)
Recording Paper Size
(North America)
Recording Paper Size
(A/B format)
Compatibility
Communication Modes
Communication
Resolution
A3, A4, A4-R, A5, A5-R, B4, B5, B5-R, FOLIO
11" x 17" (LD), 8.5" x 14" (LG), 8.5" x 11" (LT), 5.5" x 8.5" (ST), 10. 1/8" x 14" (COMP)
297 mm x 420 mm (A3), 210 mm x 297 mm (A4), 148 mm x 210 mm (A5),
257 mm x 364 mm (B4), 182 mm x 257 mm (B5), 210 mm x 330 mm (FOLIO)
Exclusive Mode, ECM, G3
Transmission Rate
Encoding Systems
Memory Capacity
Unit Type
Applicable Network
Horizontal: 8 dots/mm, 16 dots/mm, 300 dots/inch
Vertical: 3.85 lines/mm, 7.7 lines/mm, 15.4 lines/mm, 300 dots/inch
33,600/31,200/28,800/26,400/24,000/21,600/19,200/16,800/14,400/12,000/9,600/7,200/4,800/2,400 bps
JBIG/MMR/MR/MH
Transmission/Reception: 1GB
*1
Desktop type, transmitting/receiving dual type
Public Switched Telephone Network (PSTN)
*1 For hard drives, MB means 1 million bytes. (Total hard drive accessible capacity may vary depending on operating environment.)
When the total time that the power is turned off for 12 hours a day becomes about 5 years, the battery will expire. If the battery is run down, ask your service technician. (Repair and replacement will be charged.)
* Specifications and appearance are subject to change without notice in the interest of product improvement.
* If trouble occurs, call service for assistance.
Options
2nd Line for FAX Unit: GD-1260
116 Specifications of GD-1250/GD-1270
INDEX
Numerics
2nd Line for FAX Unit
........................................ 17
2-Sided originals
........................................................56
A
Administrator settings
...............................................101
Alarm lamp
................................................................13
B
Batch transmission function
........................................22
Bulletin board mailbox
................................................61
C
Canceling direct transmissions
....................................53
Canceling reserved transmissions
...............................54
Canceling the memory transmission
.............................51
Chain dial communication
...........................................74
[CLEAR] button
..........................................................13
Communication status
................................................49
COMPLETION TONE VOLUME
................................105
Confidential mailbox
...................................................61
Connecting cables
.....................................................16
Control panel
.............................................................12
D
Delayed transmission reservation
................................75
Department management
...........................................14
DIAL TYPE
.............................................................105
DIAL TYPE (LINE2)
.................................................105
Different width originals
..............................................27
Digital keys
...............................................................13
DIRECT TX
........................................................ 29
DISCARD
...............................................................106
DUPLEX PRINT
......................................................107
E
ECM
................................................................ 30
................................................................ 77
E-mail address
................................................... 77
Error codes
.............................................................114
Error messages
.......................................................114
EXPOSURE
..................................................... 29
External telephone
................................. 17
F
[FAX] button
..............................................................13
[FUNCTION CLEAR] button
........................................13
I
INITIAL PREVIEW TYPE
..........................................100
Initial setup
..............................................................104
INTERNET FAX
.........................................................30
Internet Fax
........................................................ 48
ITU-T
................................................................. 30
J
[JOB STATUS]
..........................................................14
L
LINE
.........................................................................13
LINE SELECT
...........................................................30
M
MAIL BOX COMMUNICATION
....................................30
Mailbox Transmission creating the confidential or bulletin board mailbox
creating/modifying a relay station mailbox
deleting a mailbox
.................................................. 72
deleting an original
................................................. 65
printing an original
.................................................. 64
registering an original
............................................. 62
retrieving an original
............................................... 67
sending an original
................................................. 66
MEMORY RX
........................................................... 13
MEMORY TX
...................................................... 29
MONITOR VOLUME
............................................... 105
N
Network Fax
............................................................. 48
Next original
............................................................. 22
O
Off-hook transmission
................................................ 40
Offramp gateway
....................................................... 78
On-hook transmission
................................................ 39
Onramp gateway
....................................................... 77
[OPTION]
.....................................................20
Options
.................................................................... 15
Original original scanning range
........................................... 24
originals that can be sent
........................................ 23
placing the original(s) on the original glass
placing the original(s) on the RADF
ORIGINAL MODE
............................................... 29
ORIGINAL SIZE
........................................................ 29
P
Paper acceptable size of paper
......................................... 44
default setting for RX printing
.................................. 44
paper priority when there is no same size paper
[Pause]
.................................................................. 103
Polling Communication
.............................................. 59
[PREVIEW]
........................................................ 21
PREVIEW SETTING
............................................... 100
[PRINT] button
.......................................................... 13
PRINT DATA lamp
.................................................... 13
Printing lists & reports automatically
......................................................... 87
manually
............................................................... 84
samples
................................................................ 88
Priority transmission
.................................................. 58
Q
QUALITY TX
............................................................ 30
R
Receiver information
....................................... 103
Receiving
AUTO reception
..................................................... 42
MANUAL reception
................................................ 42
Memory reception
.................................................. 43
Recipient confirming the recipients
......................................... 38
direct entry with digital keys
..................................... 32
group entry
............................................................ 34
searching for by ID number
..................................... 34
searching for the recipient’s fax number
specifying the recipient in the address book
Recovery transmission
...................................... 76
INDEX 117
Redial function
...........................................................22
REDUCTION
...........................................................107
Relay station mailbox
.................................................61
Reserved transmissions
.............................................48
RESOLUTION
.................................................... 29
ROTATE SORT
.......................................................107
RTI
.........................................................................100
RX MODE
...............................................................105
RX ONLY (24HR)
....................................................109
RX ONLY (TIMER)
...................................................109
RX printing
..............................................................106
S
Save as File
..............................................................79
SECURE RECEIVE FORCED SETTING
Sender information
.......................................... 103
Sending
....................................................................20
SMTP server
.............................................................78
Specifications
..........................................................116
[START] button
..........................................................13
[STOP] button
...........................................................13
T
Telephone line
...........................................................17
Terminal ID
.............................................................103
Touch panel
..............................................................14
Transmission conditions changing the settings for each page
making settings
......................................................28
Trouble
...................................................................115
TTI
.........................................................................100
TX / RX
...................................................................109
TX TYPE
............................................................ 29
U
[USER FUNCTIONS] button
........................................13
User management
.....................................................14
User Settings
.............................................................98
118 INDEX
Printed in Malaysia
GD-1250/1260/1270
OME100080D0
MULTIFUNCTIONAL DIGITAL SYSTEMS
Operator’s Manual for FAX Unit
1-11-1, OSAKI, SHINAGAWA-KU, TOKYO, 141-8562, JAPAN
©2011 - 2013 TOSHIBA TEC CORPORATION All rights reserved
6LJ05571000
R100520J3004-TTEC
Ver04 F 2013-04

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Sending and receiving faxes
- Creating mailboxes
- Setting transmission conditions
- Polling communication
- Priority transmission
- Delayed transmission reservation
- Recovery transmission