advertisement
▼
Scroll to page 2
of 17
User Manual TABLE OF CONTENTS 1. Before You Begin................................................................................3 What Is Included ........................................................................................... 3 Unpacking Instructions .................................................................................. 3 Claims ................................................................................................................... 3 Text Conventions .......................................................................................... 3 Symbols ........................................................................................................ 3 Document Information ................................................................................... 3 Product at a Glance....................................................................................... 4 Safety Notes ................................................................................................. 4 2. Introduction.........................................................................................5 Product Overview .......................................................................................... 5 Product Dimensions ...................................................................................... 6 3. Setup ...................................................................................................7 AC Power ...................................................................................................... 7 Fuse Replacement ................................................................................................. 7 Power Linking ........................................................................................................ 8 Mounting ....................................................................................................... 9 Orientation ............................................................................................................. 9 Rigging .................................................................................................................. 9 4. Operation ..........................................................................................10 Control Panel Operation .............................................................................. 10 Menu Map ................................................................................................... 10 Configuration (DMX).................................................................................... 11 DMX Personalities and Starting Address .............................................................. 11 DMX Channel Assignments and Values....................................................... 12 3-CH.................................................................................................................... 12 7-CH.................................................................................................................... 12 24-CH.................................................................................................................. 13 Configuration (Standalone) .......................................................................... 14 Static Color Mode ................................................................................................ 14 Automatic Mode ................................................................................................... 14 Custom Static Color Mode.................................................................................... 14 Master/Slave Mode .............................................................................................. 15 5. Technical Information ......................................................................15 Product Maintenance .................................................................................. 15 6. Technical Specifications ..................................................................16 Contact Us .................................................................................................. 17 Returns ....................................................................................................... 17 Page 2 of 17 COLORbar™ SMD User Manual (Rev. 2) 1. BEFORE YOU BEGIN What Is Included • • COLORbar™ SMD Locking Power Cord • • Warranty Card Quick Reference Guide Unpacking Instructions Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition. Claims If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier immediately, not CHAUVET®. Failure to report damage to the carrier immediately may invalidate your claim. In addition, keep the box and contents for inspection. For other issues, such as missing components or parts, damage not related to shipping, or concealed damage, file a claim with CHAUVET® within 7 days of delivery. Text Conventions Symbols Convention 1~512 50/60 Settings Menu > Settings <ENTER> ON Symbol Meaning A range of values A set of values of which only one can be chosen A menu option not to be modified A sequence of menu options to be followed A key to be pressed on the product’s control panel A value to be entered or selected Meaning Critical installation, configuration, or operation information. Not following these instructions may make the product not work, cause damage to the product, or cause harm to the operator. Important installation or configuration information. The product may not function correctly if this information is not used. Useful information. Document Information The information and specifications contained in this User Manual are subject to change without notice. CHAUVET® assumes no responsibility or liability for any errors or omissions, and reserves the right to revise or recreate this manual at any time. Download the latest version from www.chauvetlighting.com. You can download the latest version of this document from www.chauvetlighting.com. © Copyright 2012 CHAUVET®. All rights reserved. Electronically published by CHAUVET® in the United States of America. Author Date Editor Date A. Diaz 1/17/12 S. Diaz 9/19/12 COLORbar™ SMD User Manual (Rev. 2) Page 3 of 17 Product at a Glance Use on Dimmer Outdoor Use Sound Activated DMX Master/Slave Safety Notes Auto Programs Auto-ranging Power Supply Replaceable Fuse User Serviceable Duty Cycle Please read the following Safety Notes carefully before working with the product. The Notes include important safety information about installation, usage, and maintenance. • • • • • • • • • • • • • • • • • • • Page 4 of 17 Always connect the product to a grounded circuit to avoid the risk of electrocution. Always disconnect the product from the power source before cleaning or replacing the fuse. Avoid direct eye exposure to the light source while the product is on. Make sure the power cord is not crimped or damaged. Never disconnect the product from power cord by pulling or tugging on the cord. If mounting the product overhead, always secure to a fastening device using a safety cable. Make sure there are no flammable materials close to the product when operating. Do not touch the product’s housing when operating because it may be very hot. Always make sure that the voltage of the outlet to which you are connecting the product is within the range stated on the decal or rear panel of the product. The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose the product to rain or moisture. Always install the product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces. Be sure that no ventilation slots on the product’s housing are blocked. Never connect the product to a dimmer. Make sure to replace the fuse with another of the same type and rating. Never carry the product from the power cord or any moving part. Always use the hanging/mounting bracket or the handles. The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the product at higher temperatures. In the event of a serious operating problem, stop using the product immediately. Never try to repair the product. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Keep this User Manual for future use. If you sell the product to another user, be sure that they also receive this document. COLORbar™ SMD User Manual (Rev. 2) 2. INTRODUCTION Product Overview Power In Fuse Holder Microphone Bracket Adjustment Knob 3-pin DMX In 5-pin DMX In LED Display Sound Sensitivity Knob Safety Loop 5-pin DMX Out 3-pin DMX Out Power Out COLORbar™ SMD User Manual (Rev. 2) Page 5 of 17 Product Dimensions Page 6 of 17 COLORbar™ SMD User Manual (Rev. 2) 3. SETUP AC Power The COLORbar™ SMD has an auto-ranging power supply and it can work with an input voltage range of 100~240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. The listed current rating indicates the product’s average current draw under normal conditions. Always connect the product to a protected circuit (circuit breaker or fuse). Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire. Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel serves only as a 0% to 100% switch. Fuse Replacement Follow the instructions below to change the fuse, if necessary. Disconnect the product from the power outlet before replacing the fuse. 1. 2. 3. 4. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder. Pry the fuse holder out of the housing. Remove the blown fuse from the holder and replace with a fuse of the exact same type and rating. Insert the fuse holder back in place and reconnect power. Installed fuse (held by plastic clip) Safety cap Spare fuse holder (inside safety cap) The product does not ship with a spare fuse; however, the safety cap has room for a spare. COLORbar™ SMD User Manual (Rev. 2) Page 7 of 17 Power Linking Power Linking Diagram The product provides power linking via the IEC outlet located in the back of the unit. Please see the diagram below for further explanation. 1st Product 2nd Product 3rd Product Other products You can power link up to three (3) COLORbar™ SMD units @ 120 VAC or up to six (6) COLORbar™ SMD units @ 230 VAC. The power linking diagram shown above corresponds to the North American version of the product ONLY! If using the product in other markets, you must consult with the local CHAUVET® distributor as power linking connectors and requirements may differ in your country or region. Page 8 of 17 COLORbar™ SMD User Manual (Rev. 2) Mounting Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The COLORbar™ SMD may be mounted in any position; however, make sure adequate ventilation is provided around the product. Rigging • Before deciding on a location for the product, always make sure there is easy access to the product for maintenance and programming purposes. • Make sure that the structure onto which you are mounting the product can support the product’s weight. See the Technical Specifications section of this manual for weight information. • When mounting the product overhead, always use a safety cable. Mount the product securely to a rigging point, whether an elevated platform or a truss. • When rigging the product onto a truss, you should use a mounting clamp of appropriate weight capacity. The bracket has a 13-mm hole, which is appropriate for this purpose. • When power linking multiple products, you must always consider the length of the power linking cable and mount the products close enough for the cable to reach. • The bracket adjustment knobs allow for directional adjustment when aiming the product to the desired angle. Only loosen or tighten the bracket knobs manually. Using tools could damage the knobs. Mounting Bracket Bracket Adjustment Knob Mounting Diagram U Brackets Text(xhere 2) COLORbar™ SMD User Manual (Rev. 2) Page 9 of 17 4. OPERATION Control Panel Operation To access the control panel functions, use the four buttons located underneath the display. Please refer to the Product Overview to see the button locations on the control panel. Button <MENU> <UP> Menu Map Press to find an operation mode or to back out of the current menu option Press to scroll up the list of options or to find a higher value <DOWN> Press to scroll down the list of options or to find a lower value <ENTER> Press to activate a menu option or a selected value Mode Static Colors Auto Programs Page 10 of 17 Function Programming Steps C-- P-- Description C1 Red C2 Green C3 Blue C4 Cyan C5 Magenta C6 Yellow C7 White P1 7-Color Switching P2 7-Color Fading P3 3-Color Switching P4 3-Color Fading P5 Chase program P6 Sound-Active Chase program Program Speed S-- S001-S100 Custom Color Mixing R000-R100 Red U-- G000-G100 Green b000-b100 Blue DMX Personalities 7-CH d001-d512 Selects DMX starting address Selects auto program speed 3-CH 24CH COLORbar™ SMD User Manual (Rev. 2) Configuration (DMX) DMX Personalities and Starting Address Set 1. 2. 3. the product in DMX mode to control with a DMX controller. Connect the product to a suitable power outlet. Turn the product on. Connect a DMX cable from the DMX output of the DMX controller to the DMX input socket on the product. The COLORbar™ SMD has three DMX personalities, from a 3-channel mode for basic control to a 24-channel mode with more advanced control over the lights. The COLORbar™ SMD uses up to 24 DMX channels in its 24-channel DMX mode, which defines the highest configurable address to 489. When selecting a starting DMX address, always consider the number of DMX channels the selected DMX mode uses. If you choose a starting address that is too high, you could restrict the access to some of the product’s channels. If you are not familiar with the DMX protocol, you may refer to the DMX Primer at www.chauvetlighting.com. To select the DMX personality, do the following: 1. Press <MENU> repeatedly until 3-CH, 7-CH, or 24CH shows on the display. 2. Press <ENTER> to choose your DMX personality when it appears on the display. To then choose your starting address: 1. The display should show d 1 once you’ve selected your DMX personality using the steps above. 2. Use <UP> or <DOWN> to select the starting address. 3. Press <ENTER>. COLORbar™ SMD User Manual (Rev. 2) Page 11 of 17 DMX Channel Assignments and Values 3-CH 7-CH Channel Function Setting 1 Red 000 255 0~100% 2 Green 000 255 0~100% 3 Blue 000 255 0~100% Channel Function Value Setting 1 Red 000 255 0~100% 2 Green 000 255 0~100% 3 Blue 4 Color Macros 000 255 0~100% 000 255 No function 000 255 Color Macros Speed (slow to fast) 000 255 (when CH.6 is 026~225) 000 255 No function 000 255 0~30 Hz Speed 5 Page 12 of 17 Value Strobe 6 Auto Programs 7 Dimmer 000 025 026 050 051 075 076 100 101 125 126 150 151 175 176 200 201 225 No Function Fading 0~100% Fading100%~0 Fading 100%~0~100% Auto program P1 Auto program P2 Auto program P3 Auto program P4 Auto program P5 226 255 Sound-Active mode (Auto program P6) 000 255 0~100% COLORbar™ SMD User Manual (Rev. 2) 24-CH Channel Function Value Setting Section 1 Red 000 255 0~100% 2 Green 000 255 0~100% 3 Blue 000 255 0~100% 4 5 6 Red Green Blue 000 255 0~100% 000 255 0~100% 000 255 0~100% 2 7 8 9 Red Green Blue 000 255 0~100% 000 255 0~100% 000 255 0~100% 3 10 11 12 Red Green Blue 000 255 0~100% 000 255 0~100% 000 255 0~100% 4 13 14 15 Red Green Blue 000 255 0~100% 000 255 0~100% 000 255 0~100% 5 16 17 18 Red Green Blue 000 255 0~100% 000 255 0~100% 000 255 0~100% 6 19 20 21 Red Green Blue 000 255 0~100% 000 255 0~100% 000 255 0~100% 7 22 23 24 Red Green Blue 000 255 0~100% 000 255 0~100% 000 255 0~100% 8 COLORbar™ SMD User Manual (Rev. 2) 1 Page 13 of 17 Configuration (Standalone) Set the product in one of the standalone modes to control without a DMX controller. 1. Connect the product to a suitable power outlet. 2. Turn the product on. Never connect a product that is operating in any standalone mode (either Static, Automatic, or Sound) to a DMX string connected to a DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller. Static Color Mode Automatic Mode To enable the Static Color Mode, do the following: 1. Press <MENU> repeatedly until C-- shows on the display. 2. Press <ENTER>. 3. Use <UP> or <DOWN> to choose a color (C1-C7). 4. Press <ENTER>. To enable the Automatic Mode, follow the instructions below: 1. Press <MENU> repeatedly until P-- shows on the display. 2. Press <ENTER>. 3. Use <UP> or <DOWN> to choose your auto program (P1-P7). 4. Press <ENTER>. You can adjust the speed of the automatic program as well. 1. Press <MENU> repeatedly until S-- shows on the display. 2. Press <ENTER>. 3. Use <UP> or <DOWN> to adjust the duration of each step of the automatic program from S001 (slow) to S100 (fast). 4. Press <ENTER>. Custom Static Color Mode Page 14 of 17 To enable the Custom Static Color Mode, follow the instructions below: 1. Press <MENU> repeatedly until U-- shows on the display. 2. Press <ENTER>. 3. Press <UP> or <DOWN> to choose between colors (R--, G--, b--). 4. Press <ENTER>. 5. Press <UP> or <DOWN> to choose the intensity of the color (000-100). 6. Repeat the steps to mix additional colors to create the color you need. COLORbar™ SMD User Manual (Rev. 2) Master/Slave Mode The Master/Slave mode allows a single COLORbar™ SMD unit (the “master”) to control the actions of one or more COLORbar™ SMD units (the “slaves”) without the need of a DMX controller. The master unit will be set to operate in either Automatic or Sound Active mode, while the slave units will be set to operate in Slave Mode. Once set and connected, the slave units will operate in unison with the master unit. Configure the units as indicated below. Slave units: 1. Press <MODE> repeatedly until d 1 shows on the display. 2. Press <ENTER> to accept. 3. Set the DMX address to 001. 4. Connect the DMX input of the first slave unit to the DMX output of the master unit. 5. Connect the DMX input of the subsequent slave units to the DMX output of the previous slave unit. 6. Finish setting and connecting all the slave units. Master unit: 1. Set the master unit to operate in either Automatic or Sound mode. 2. Make the master unit the first unit in the DMX daisy chain. • Configure all the slave units before connecting the master unit to the DMX daisy chain. • Never connect a DMX controller to a DMX string configured for Master/Slave operation because the controller may interfere with the signals from the master unit. • Do not connect more than 31 slave units to the master unit. 5. TECHNICAL INFORMATION Product Maintenance Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life. To maintain optimum performance and minimize wear, you should clean your lighting products at least twice a month. However, be aware that usage and environmental conditions could be contributing factors to increase the cleaning frequency. To clean the product, follow the instructions below: • Unplug the product from power. • Wait until the product is cold. • Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external surface/vents. • Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl alcohol. • Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue. • Softly wipe any dirt or grime to the outside edges of the transparent surface. • Gently polish the transparent surfaces until they are free of haze and lint. Always dry the transparent surfaces carefully after cleaning them. COLORbar™ SMD User Manual (Rev. 2) Page 15 of 17 6. TECHNICAL SPECIFICATIONS Dimensions and Weight Length Width Height Weight 31.8 in (803 mm) 4.7 in (121 mm) 7 in (178 mm) 12 lbs (5.4 kg) Note: Dimensions in inches rounded to the nearest decimal digit. Power Light Source Photo Optic Thermal DMX Ordering Page 16 of 17 Power Supply Type Range Voltage Selection Switching (internal) 100~240 V, 50/60 Hz Auto-ranging Parameter 120 V, 60 Hz 230 V, 50 Hz Consumption 300 W 292 W Operating 2.3 A 1.3 A Power linking current (units) 8 A (3 units) 8 A (6 units) Fuse F 5 A, 250 V F 5 A, 250 V Power I/O US/Worldwide UK/Europe Power input connector IEC IEC Power output connector Edison IEC Power Cord plug Edison (US) Local plug Type Lifespan SMD LED 50,000 hours Color Quantity Current Tri-color 648 20 mA x 3 Parameter Illuminance @ 2 m 328 lx Strobe Rate 0~30 Hz Beam angle 67º Field angle 110° Viewing angle 120° Maximum External Temp. Cooling System 104° F (40° C) Convection I/O Connectors Connector Type Channel Range 3-pin and 5-pin XLR Sockets 3, 7, 24 Product Name Item Code Item Number COLORbar™ SMD 03030478 COLORBARSMD COLORbar™ SMD User Manual (Rev. 2) To return a product or request support: • • • Contact Us In the U.S., contact CHAUVET® World Headquarters (see below). In the UK or Ireland, contact CHAUVET® Europe Ltd. (see below). In any other country, DO NOT contact CHAUVET®. Instead, contact your distributor of record. Refer to our website for contact details of distributors outside the U.S., United Kingdom, or Ireland. World Headquarters CHAUVET® General Information Address: 5200 NW 108th Avenue Sunrise, FL 33351 Voice: (954) 929-1115 Fax: (954) 929-5560 Toll free: (800) 762-1084 Technical Support Voice: (954) 929-1115 (Press 4) Fax: (954) 756-8015 Email: [email protected] World Wide Web www.chauvetlighting.com United Kingdom & Ireland CHAUVET® Europe Ltd. General Information Address: Unit 1C Brookhill Road Industrial Estate Pinxton, Nottingham, UK NG16 6NT Voice: +44 (0)1773 511115 Fax: +44 (0)1773 511110 Technical Support Email: [email protected] World Wide Web www.chauvetlighting.co.uk If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of record and follow their instructions on how to return CHAUVET® products to them. Visit our website for contact details. Returns Call the corresponding CHAUVET® Tech Support office and request a Return Merchandise Authorization (RMA) number before shipping the product. Be prepared to provide the model number, serial number, and a brief description of the cause for the return. You must send the merchandise prepaid, in its original box, and with its original packing and accessories. CHAUVET® will not issue call tags. Clearly label the package with the RMA number. CHAUVET® will refuse any product returned without an RMA number. Write the RMA number on a properly affixed label. DO NOT write the RMA number directly on the box. Before sending the product, clearly write the following information on a piece of paper and place it inside the box: • Your name • Your address • Your phone number • The RMA number • A brief description of the problem Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be your responsibility. FedEx packing or double-boxing are recommended. CHAUVET® reserves the right to use its own discretion to repair or replace returned product(s). COLORbar™ SMD User Manual (Rev. 2) Page 17 of 17
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement