Scosche GM1595 installation kit User manual

Add to My manuals
1 Pages

advertisement

Scosche GM1595 In-Dash Installation Kit for 2005-Up Select GM Vehicles - User Manual | Manualzz

IN-DASH INSTALLATION KIT FOR

2005-UP SELECT GM VEHICLES

BUICK

2005-UP TERRAZA

CHEVROLET

2005-UP CORVETTE

2005-UP UPLANDER

PONTIAC

2005-UP MONTANA SV6

SATURN

2005-UP RELAY

5908L

BRACKET

GM1595

5908R

BRACKET

5906 KIT PANEL

5907 TRIM RING

INTRODUCTION

This premium installation kit is for 2005-UP Select GM Vehicles. Included are all the parts you need to mount your car stereo/cassette or CD player into your vehicle's dash. Refer to the individual instruction in this manual to remove your vehicle's factory radio and assemble the kit.

CAUTION: Disconnect your vehicle's negative battery terminal before the installation to help prevent electrical damage. We recommend the use of a volt/ohm meter over a test light to check wiring. A test light or grounded wire probe can cause damage to the vehicle's computer and/or diagnostic systems.

Avoid all factory air bag wiring - air bags can accidentally deploy causing serious injury or death.

NOTES:

• See your vehicle's instructions for any special tools your installation might require.

• Read all instructions accompanying your car stereo/cassette player for proper wiring and mounting instructions.

SCOSCHE STEREO INSTALLATION COMPONENTS

MOUNTING THE RADIO

DOUBLE DIN-ISO & 2 DIN-ISO MOUNT

(DIN-E Radio with Side Mounting Holes)

1. Snap the DIN-ISO side mounting brackets to the back of the mounting panel (1 left and 1 right). Use supplied hardware to bolt them to the back of the kit panel.

2. Snap the DIN-ISO trim ring into the radio opening.

3. Load the radio from the REAR of the mounting panel until the nose piece of the radio comes through the front of the kit.

4. Use the 5MM screws to secure the radio from the sides.

CAUTION:

REAR SUPPORTING THE

RADIO ADDS TO THE

INSTALLATION’S

STRUCTURAL INTEGRITY.

5908L

BRACKET

VARIOUS REAR

SUPPORTS

(NOT INCLUDED)

VARIOUS REAR

SUPPORTS

(NOT INCLUDED)

5907 TRIM

RING

5906 KIT

PANEL

5908R

BRACKET

5908L

BRACKET

5906 KIT

PANEL

5908R

BRACKET

5907 TRIM

RING

2005-UP Buick Terraza

2005-UP Chevrolet Uplander

2005-UP Pontiac Montana SV6

2005-UP Saturn Relay

RADIO REMOVAL

1. Using a panel removal tool, remove the trim around the radio and climate control.

2. Extract (8) Phillips head screws securing A/C controls and radio. Lift away, disconnect, and remove.

2005-UP Chevrolet Corvette

NOTE: Factory Radio has anti-theft lockout when unplugged. It can only be reset by a Chevrolet dealership.

RADIO REMOVAL

1. Open center console compartment, extract (4) Phillips screws securing compartment lid and remove.

2. Pop up leather parking brake boot and extract (2) hex screws from behind.

3. Use a panel removal tool to pop out the passenger airbag indicator panel (rear edge first), unplug and remove.

4. Extract (2) hex screws revealed in step 3.

5. Carefully pop out entire radio/climate control bezel, unplug all connections and remove.

6. Extract (6) hex screws holding radio/climate assembly, unplug and remove.

STEREO DASH KITS

advertisement

Key Features

  • In-dash installation kit
  • For select GM vehicles
  • Includes all mounting parts
  • Easy to install
  • Various rear supports
  • For Double DIN and 2 DIN-ISO radios

Related manuals

Frequently Answers and Questions

What vehicles is this installation kit compatible with?
This kit is designed for select GM vehicles from 2005 onwards. The specific models mentioned in the manual include Buick Terraza, Chevrolet Uplander, Pontiac Montana SV6, and Saturn Relay. The kit also includes installation instructions for the 2005-UP Chevrolet Corvette.
How do I mount the radio using the kit?
The manual outlines the following steps to mount the radio: 1. Snap the DIN-ISO side mounting brackets to the back of the mounting panel. 2. Snap the DIN-ISO trim ring into the radio opening. 3. Load the radio from the rear of the mounting panel until the nose piece of the radio comes through the front of the kit. 4. Secure the radio from the sides using the 5MM screws.
What is the importance of the rear supporting brackets?
According to the manual, the rear supporting bracket for the radio adds to the installation's structural integrity. This suggests that the bracket helps to ensure the radio is securely mounted and prevents it from becoming loose or damaged.
Download PDF

advertisement