GE Profile™ Series 30" Built-In Touch Control Induction Cooktop
Dimensions and Installation Information (in inches)
Important: Requires a 5" free area between
the bottom of the cooktop to any combustible
material, i.e., shelving. Free area not required
when installing wall oven underneath cooktop.
Refer to installation instructions. Requires a 15"
minimum from cooktop to adjacent overhead
cabinets. Units are furnished with a 48" flexible
armored cable.
Note: 30" induction cooktops are approved for use
over select GE 27" and GE 30" Single Wall Ovens and
Warming Drawers. Refer to cooktop and wall oven/
warming drawer installation instructions packed
with product for current dimensional data. If installed
with a GE Telescopic Downdraft System, consult both
the cooktop and downdraft installation instructions
packed with product before installing. Cooktop gas/
electric supply may need to be re-routed to install
downdraft. The countertop cutout requires 23-1/2"
minimum flat countertop surface and 25" minimum
total countertop depth. In addition, other clearances
to front edge of the countertop must be considered.
Before installing, consult installation instructions
packed with product for ­current dimensional data.
Cutout filler trim kit: A filler trim kit is available for
use if your countertop cutout is larger than the
dimension shown, up to 29-13/16" x 20-7/16". Order
JXTR32B for black or JXTR32W for white, to reduce
the cutout opening for installation of this cooktop.
These kits may be ordered from your GE Dealer.
Approximate Cooking Dimensions
13" MAX. depth of unprotected
overhead cabinets (when no
hood or microwave is installed)
4-5/8" at baffle near center
ofunit (except when installed
above an approved wall
oven) and 3-1/4" at rear
of air intake
to 19-3/4"
28-1/2" to
1-3/4" MIN.
to rear wall
30" MIN. from countertop to
unprotected cabinet (when
no hood or microwave is
15" MIN. height from countertop
to nearest cabinet (including
light rails) on both sides of
2-1/2" MIN.
Electrical junction box 16" MIN.
below countertop
To insure accuracy, it is best to make a
template when cutting the opening in the counter
2" MIN. clearance
to side wall from cut-out
on both sides of cooktop
KW Rating
30.8 Amps†
30.8 Amps†
Note: Check local codes for
required breaker size
Listed by
For answers to your Monogram® or GE appliance
questions, visit our website at geappliances.com
or call GE Answer Center® service, 800.626.2000.
Specification Created 1/15
GE Profile™ Series 30" Built-In Touch Control Induction Cooktop
Features and Benefits
• Four Induction elements - Enjoy a new level of rapid, precise
heating with a cool-to-the-touch surface that’s easy to clean
• Digital touch controls - Accurately control your heating and
enjoy an easy to clean surface
• 11" 3,700-watt induction element - Rapidly boil water with
GE's most powerfull induction element
• SyncBurners - Control two 7" elements simultaneously to
evenly heat large cookware or griddles*
• Kitchen timer - Helps coordinate meal preparation and cooking
• Control lock capability - Protects against unintended activation
• Pan presence & size sensor - Cook efficiently with elements
that heat to the size of your pan and shut off when no
pan is present
• Red LED display with black glass surface and stainless steel
trim - Achieve a modern look that complements the entire
kitchen and other stainless steel appliances
*Optional Stainless Steel Clad Aluminum Griddle
Achieve even results with this lightweight griddle,
tailored to fit GE SyncBurners. Order part number
JXGRIDL1 from your GE Dealer.
• Hot surface indicator lights - Know when elements are too
hot to touch with a quick glance
• Model PHP9030SJSS - Stainless Steel
Specification Created 1/15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF