220 VOLT COMPRESSOR

4 HP PEAK – 29 GALLON

92504

SET uP ANd OPERATiNG iNSTRuCTiONS

distributed exclusively by Harbor Freight Tools

®

.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THiS MANuAL.

Copyright

©

2005 by Harbor Freight Tools

®

. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of

Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

COVER REViSEd 06b, 08g

PROduCT SPECiFiCATiONS

Motor

Overload Reset Button

Power Cord

220 V~ / 60 Hz / 12.5 A (Load) / Single Phase / 4 HP Peak /

3 HP Working / 3,400 RPM / Two Capacitor (Run & Start)

15 A

12 Gauge, 3-Wire (Stripped), 10 Ft. Long

220 Volt Power Cord Plug Not Included.

29 Gallons Air Tank Capacity

CFM Airflow

Compressor Pump Type

Safety Valve Setting

Air Pressure Gauge Indicators

Automatic Shut Off Capability

16.4 @ 40 PSI / 15.7 @ 70 PSI /

14.5 @ 90 PSI / 13.0 @ 115 PSI

Dual V-Head Cylinder / Belt Driven

120 PSI

0-200 PSI in 5 PSI Increments

Shut Off at 115 PSI / Starts at 80 PSI

Required Air Quick Connectors (Not Included) Qty. 2 / 1/4”-18 NPT Quick Connectors

V-Belt Size A1118 Li

Base Mounting Holes

Weight

Qty. 4 @ 1/2” Diameter

205 Pounds

uNPACKiNG

When unpacking, check to make sure all the parts shown on the Parts List at the end of the manual are included. If any parts are missing or broken, please call Harbor

Freight Tools at the number shown on the cover of this manual as soon as possible.

SAVE THiS MANuAL

You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep this manual and invoice in a safe and dry place for future reference.

GENERAL SAFETY RuLES

WARNiNG!

REAd ANd uNdERSTANd ALL iNSTRuCTiONS

Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.

SAVE THESE iNSTRuCTiONS

1.

WORK AREA

Keep your work area clean and well lit.

Cluttered benches and dark areas invite accidents.

SKU 92504 For technical questions, please call 1-800-444-3353.

REV 06b, 08i

Page 2

2.

3.

1.

2.

3.

4.

1.

2.

3.

4.

5.

do not operate compressors in explosive atmospheres, such as in the pres-

ence of flammable liquids, gases, or dust. Compressors create sparks which may ignite the dust or fumes.

Keep bystanders, children, and visitors away while operating a compressor.

Provide barriers or shields as needed.

ELECTRiCAL SAFETY

Grounded compressors must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the

outlet is properly grounded. If the compressors should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user.

do not expose compressors to rain or wet conditions.

Water entering an electric motor will increase the risk of electric shock.

do not abuse the Power Cord.

Never use the Power Cord to pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp edges, or

moving parts. Replace damaged Power Cords immediately. Damaged Power

Cords increase the risk of electric shock.

AN ExTENSiON CORd MuST NEVER bE uSEd WiTH THiS iTEM. Connecting this item to an outlet through an extension cord MAY CAuSE ELECTRiCAL dAMAGE TO THE MOTOR and could present a FiRE HAzARd.

PERSONAL SAFETY

Stay alert. Watch what you are doing, and use common sense during use.

Do not use while tired or under the influence of drugs, alcohol, or medica-

tion. A moment of inattention while operating may result in serious personal injury.

dress properly. do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.

Avoid accidental starting.

be sure the Power Switch is turned off before

plugging in. Plugging in compressors with the Power Switch on, invites accidents.

Remove adjusting keys or wrenches before turning the compressor on.

A wrench or a key that is left attached to a rotating part of the compressor may result in personal injury.

do not overreach. Keep proper footing and balance at all times.

SKU 92504 For technical questions, please call 1-800-444-3353. Page 3

6.

1.

2.

3.

4.

5.

6.

7.

1.

2.

use safety equipment. Always wear eye protection.

Make sure you are wearing your protective clothing, safety glasses with side shields and dust mask or air respirator, if appropriate.

TOOL uSE ANd CARE

do not force the compressor. use the correct compressor for your applica-

tion. The correct compressor will do the job better and safer at the rate for which it is designed. Never attempt to force the compressor to provide more pressure than it was designed for.

do not use the compressor if the Power Switch does not turn it on or turn it

off. Any compressor that cannot be controlled with the Power Switch is dangerous and must be repaired or replaced.

disconnect the Power Cord Plug from the power source before making any

adjustments, changing accessories, or storing the compressor. Such preventive safety measures reduce the risk of starting the compressor accidentally.

Keep idle compressors out of reach of children and other untrained persons.

Compressors are dangerous in the hands of untrained users.

Maintain compressors with care. Keep all components of this product clean

and dry. Do not use a damaged compressor. Tag damaged compressors “Do not use” until repaired.

Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the compressor’s operation. if damaged,

have the compressor serviced before using. Many accidents are caused by poorly maintained compressors.

use only accessories that are recommended by the manufacturer for your

model. Accessories that may be suitable for one compressor may become hazardous when used on another compressor.

SERViCE

Compressor service must be performed only by qualified repair personnel.

Service or maintenance performed by unqualified personnel could result in a risk of injury.

When servicing a compressor, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this

manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury.

SKU 92504 For technical questions, please call 1-800-444-3353. Page 4

1.

2.

3.

4.

5.

6.

7.

8.

SPECiFiC SAFETY RuLES

CAuTiON! Prior to its first use, and thereafter prior to each subsequent use, make sure to fill the Air Compressor with a premium quality, 30 weight, non-

detergent oil to the specified level. Running the Air Compressor with no oil or with low oil will cause damage to the equipment and void its warranty. Refer to the

“Operating Instructions” section for details on filling the Air Compressor with oil.

When filling the Air Compressor with oil, make sure to unscrew (do not pull) the Oil Fill Cap to remove.

use eye and ear protection.

Always wear ANSI-approved safety impact eye goggles, and ear plugs when using the Air Compressor.

Make sure all tools and equipment used with the Air Compressor are rated to

the appropriate air pressure capacity of the Air Compressor. Do not use any tool or equipment that does not operate from 0-115 PSI. If necessary, check the owner’s manual of the tool or equipment for its air pressure rating.

Always disconnect the Air Compressor from its electrical outlet, release any remaining air pressure from the unit, and disconnect all pneumatic tools and equipment from the unit, before performing any services or maintenance.

Avoid injury. Never direct the air jet at people or animals.

inspect safety valve daily

. If the safety valve is not working properly, tank pressure can build up to dangerous levels. The tank could explode. For this reason, pull the ring on the safety valve before each use and verify that it operates freely.

Replace safety valve if it does not operate freely.

Never remove or alter the factory sealed Safety Release Valve.

do not attempt to readjust the automatic start and shutoff valves.

Any change to the automatic ON/OFF pressure levels will cause additional stress on the motor, which may result in shortened motor life.

9.

drain the Air Compressor’s air tank every day.

Do not allow moisture to build up inside the Air Tank.

10.

11.

Avoid risk of tank explosion

.

a. Avoid weakening of tank by draining condensation after each use.

b. Never modify tank by drilling holes, welding to it, or modifying it’s parts.

c. The tank is designed, and factory set, to operate within a specific pressure range.

For that reason, never make adjustments to, or substitute parts, to the compressor.

12.

do not unscrew the tank drain valve so that more than four threads are showing.

Avoid bodily injury from moving parts

. The compressor cycles on automatically, without notice. For this reason, always keep hands and arms away from compres-

SKU 92504 For technical questions, please call 1-800-444-3353. Page 5

13. sor parts when the unit is connected to electrical power. Always have compressor safety guards in place before turning compressor on.

use approved air hose

. Never use plastic or PVC pipe (unless specified for Air

Compressors) to carry air under pressure. Regardless of its pressure rating, it can burst under pressure. Use only metal pipe.

14.

15.

16.

Never plug the power cord of this product into an electrical outlet while standing on a wet or damp surface.

THiS AiR COMPRESSOR MAY REquiRE A dEdiCATEd ELECTRiCAL CiR-

CuiT AS THE AMPERAGE dRAW uNdER FuLL LOAd, COMbiNEd WiTH uSE

OF ANY OTHER iTEM, MAY OVERLOAd YOuR CiRCuiT.

Always turn off the Air Compressor in the event of a power failure.

17.

18.

Performance of this Air Compressor may vary depending on variations in local line voltage.

Maintain labels and nameplates on the Air Compressor.

These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement.

19. WARNiNG! People with pacemakers should consult their physician(s) before using this product. Electromagnetic fields in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker.

20. WARNiNG! The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm).

(California Health & Safety code § 25249.5, et seq.)

21. WARNiNG! The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

SAVE THESE iNSTRuCTiONS

1.

2.

GROuNdiNG

WARNiNG! The Power Cord (31) requires the attachment of a 220 volt,

grounded, 3-Prong Plug (not included). For safety purposes, only a qualified, certified, electrician should attach a Plug to the Power Cord. Never modify the

Plug in any way. To comply with the National Electric Code, and to provide additional protection from the risk of electrical shock, this product should only be connected to a 220 volt electrical outlet that is properly grounded.

do not use the tool if the Power Cord or Plug is damaged.

If damaged, have it repaired by a qualified service facility before use.

SKU 92504 For technical questions, please call 1-800-444-3353. Page 6

Symbology

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

V~

Volts Alternating Current

A

Amperes n0 xxxx/min.

No Load Revolutions per Minute

(RPM)

To extend the life of your air tools and equipment, install an oiler and water filter in series with the Air Outlet Valves (4) of the Air Compressor.

ASSEMbLY iNSTRuCTiONS

To Attach A Power Cord Plug:

The Power Cord (31) requires the attachment of a 220 volt, grounded,

3-Prong Plug (not included). For safety purposes, only a qualified, certified, electrician should attach a Plug to the Power Cord. Never modify the Plug in any way. To comply with the National Electric Code, and to provide additional protection from the risk of electrical shock, this product should only be connected to a 220 volt electrical outlet that is properly grounded.

To Attach quick Connectors:

Prior to use, the Air Compressor requires the attachment of a 1/4” NPT Quick

Connector (not included) to each of its two Air Outlet Valves (4). To do so, wrap approximately 4” of pipe thread sealant tape (not included) around the male threads of the

Quick Connectors. Then, firmly screw the Quick Connectors into the Air Outlet Valves.

(See Figure d.)

SKU 92504 For technical questions, please call 1-800-444-3353. Page 7

To Fill The Air Compressor With Oil:

OiL FiLL CAP

(28)

OiL LEVEL iNdiCATOR

(35)

AiR

OuTLET VALVE

(4)

AiR

OuTLET VALVE

(4)

FiGuRE d

1.

2.

3.

1.

2.

CAuTiON! Prior to its first use, and thereafter prior to each subsequent use, make sure to fill the Air Compressor with a premium quality, 30 weight,

non-detergent oil. Running the Air Compressor with no oil or low oil will cause damage to the equipment and void its warranty.

When filling the Air Compressor with oil, make sure to

unscrew (do not pull) the Oil

Fill Cap (28) to remove.

(See Figure d.)

Once the Oil Fill Cap (28) is removed, fill the Air Compressor with a premium quality, 30 weight, non-detergent oil until the level of the oil rises to the midway point in the Oil Level Indicator (35). Then, screw the Oil Fill Cap back onto the Oil Fill

Hole.

(See Figure d.)

To Mount The Air Compressor:

For added safety, it is recommended that the Air Compressor be mounted on a flat, level, sturdy, concrete floor surface capable of withstanding the weight of the Air

Compressor and any additional tools and accessories.

To mount the Air Compressor, with assistance, move the unit to the location where it is to be used. Using the four 1/2” diameter mounting holes on the feet of the

Air Compressor as a template, mark the spots where four 1/2” diameter holes will

SKU 92504 For technical questions, please call 1-800-444-3353. Page 8

3.

4. be drilled in the concrete or wood floor. Then, temporarily set the Air Compressor aside.

Use a masonry drill bit to drill the four 1/2” diameter holes (about 3”-4” deep) into the concrete. Make sure to blow out the concrete dust from the drilled holes.

Set the Air Compressor back to the location where it is to be used, and align the four 1/2” diameter mounting holes in its legs with the four predrilled 1/2” holes in the concrete or wood. Then use four minimum 3” long, 1/2” diameter, concrete anchor bolts or lag bolts (not included) to secure the Air Compressor to the concrete or wood floor.

OPERATiNG iNSTRuCTiONS

Air Compressor Pre-Start Procedures:

OVERLOAd

RESET buTTON

(42)

POWER SWiTCH

(9)

AiR

OuTLET

VALVE

LEVER

AiR

OuTLET

VALVE

(4)

FiGuRE E

0

PRESSuRE

GAuGE

(5)

AiR OuTLET

VALVE

LEVER

OiL LEVEL iNdiCATOR

(35)

SAFETY RELEASE

VALVE (3)

AiR OuTLET

VALVE

(4)

PRESSuRE

AdJuSTMENT KNOb

(6)

1. Press the Power Switch (9) down to its “OFF” position.

(See Figure E.)

2. Check the Oil Level Indicator (35), making sure the level of the oil is at the midway point in the Indicator.

(See Figure E.)

3. Check to make sure the Tank Drain Valve (33) is fully closed. NOTE: The Tank

Drain Valve is located at the bottom of the Air Tank (32).

(See Assy. diagram.)

SKU 92504 For technical questions, please call 1-800-444-3353. Page 9

4.

5.

6.

1.

2.

3.

4.

5.

6.

7.

8.

1.

2.

Turn the Pressure Adjustment Knob (6) counterclockwise all the way to its “OFF” position.

(See Figure E.)

Turn each Lever on the two Air Outlet Valves (4) backward to their closed position.

(See Figure E.)

If using only one of the two Air Outlet Valves (4), attach an air hose (not included) to the Air Outlet Valve. Then, attach the other end of the air hose to the pneumatic tool that will be used. If using both Air Outlet Valves simultaneously, attach an air hose to each Air Outlet Valve. Then, attach the other ends of the air hoses to their respective pneumatic tools.

(See Figure E.)

To Start The Air Compressor:

Plug the Power Cord Plug (31) into the nearest 220 volt, grounded, electrical outlet.

Pull up on the Power Switch (9) to its “ON” position. (See Figure E.)

Turn the Pressure Adjustment Knob (6) clockwise about halfway to its “ON” position.

(See Figure E.)

If using only one Air Outlet Valve (4), allow sufficient time for its Pressure Gauge

(5) to indicate at least 80 PSi. If using both Air Outlet Valves, allow sufficient time for both Pressure Gauges (5) to indicate at least 80 PSi.

(See Figure E.)

Check to make sure the pneumatic tools that will be used are turned off and properly connected to their air hoses.

Once the Pressure Gauge (5) has reached at least 80 PSI, turn the Lever on the

Air Outlet Valve (4) forward to its open position in order to supply air to the pneumatic tool. If both Air Outlet Valves are being used, turn both Levers forward to their open positions. (See Figure E.)

iMPORTANT:

Both Pressure Gauges (5) should always indicate the same PSI reading, meaning that if two pneumatic tools are being hooked up to the Air Compressor both pneumatic tools should operate on the same PSI rating.

If necessary, turn the Pressure Adjustment Knob (6) clockwise to increase air pressure to the pneumatic tool(s) or counterclockwise to decrease air pressure to the pneumatic tool(s).

(See Figure E.)

To use The Air Tank Safety Release Valve:

The Safety Release Valve (3) is used when decompression is needed quickly and efficiently.

(See Figure E.)

To decompress the Air Tank (32) pressure, press down on the Power Switch (9) to turn off the Air Compressor.

(See Figure E.)

SKU 92504 For technical questions, please call 1-800-444-3353. Page 10

3.

1.

2.

3.

4.

1.

2.

3.

4.

5.

6.

7.

Pull out on the Safety Release Valve Ring (3) to immediately release air pressure in the Air Tank (32).

(See Figure E.)

To use The Overload Reset button:

The Air Compressor is equipped with an internal electrical circuit breaker which is designed to automatically shut off the Air Compressor in the event its Motor (14) becomes overheated or in the event of an electrical power outage.

(See Figure E.)

Should the Air Compressor automatically shut off, press the Power Switch (9) down to its “OFF” position. (See Figure E.)

Wait several minutes to allow the Air Compressor’s Motor (14) to cool (if due to electrical power outage, wait until power is resumed).

Press the Overload Reset Button (42) to reset the electrical circuit breaker. If it does not reset, wait a few additional minutes and try again. Then, pull up on the

Power Switch (9) to its “ON” position to resume work. (See Figure E.)

To Turn Off The Air Compressor:

When finished using the Air Compressor, press down on its Power Switch (9) to turn off the unit.

(See Figure E.)

Disconnect the Power Cord Plug (31) from its electrical outlet.

Turn on the pneumatic tools to expend all remaining compressed air from the Air

Compressor, air hoses, and pneumatic tools.

Turn the Pressure Adjustment Knob (6) counterclockwise all the way to its

“OFF” position.

(See Figure E.)

Turn each Lever on the two Air Outlet Valves (4) backward to their

closed position.

(See Figure E.)

Disconnect the air hoses from the Air Outlet Valves (4).

(See Figure E.)

Disconnect the air hoses from the pneumatic tools. Then, keep the air hoses and pneumatic tools in a clean, dry location out of reach of children.

SKU 92504 For technical questions, please call 1-800-444-3353. Page 11

1.

2.

iNSPECTiON, MAiNTENANCE, ANd CLEANiNG

WARNiNG! Always make sure the Power Switch (9) is in its “OFF” posi-

tion, the Air Compressor is disconnected from its electrical outlet, and all remaining compressed air is expelled from the system before performing any inspection, maintenance, or cleaning.

before each use:

Inspect the general condition of the Air Compressor. Check for misalignment or binding of moving parts, cracked or broken parts, loose or damaged connections, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use.

do not use damaged equipment.

PCV FiLTER

(41)

OiL FiLL HOLE

OiL FiLL CAP

(28)

FiGuRE F

3. before each use: Make sure to fill the Air Compressor with a premium quality, 30

weight, non-detergent oil. Running the Air Compressor with no oil or low oil will cause damage to the equipment and void its warranty. When filling the Air Compressor with oil, make sure to unscrew (do not pull) the Oil Fill Cap (28) to remove.

Fill with oil until the level of the oil rises to the midway point in the Oil Level Indicator (35). Then, screw the Oil Fill Cap back onto the Oil Fill Hole.

(See Figure F.)

4.

NOTE:

Each time the Oil Fill Cap (28) is removed, observe the PCV Filter (41) that is located inside the Oil Fill Cap. When necessary, remove the PCV Filter and clean with a mild solvent. Allow the PCV Filter to dry. Then, replace the PCV Filter

SKU 92504 For technical questions, please call 1-800-444-3353. Page 12

in the Oil Fill Cap, and screw the Oil Fill Cap back onto the oil fill hole.

(See Figure F.)

WiNG NuT

(36)

WiNG NuT

(36)

AiR FiLTER

(38)

AiR FiLTER bOWL

(39)

AiR FiLTER CAP

(37)

FiGuRE G

5. Weekly: The Air Compressor is equipped with two Air Filters (38) which should be cleaned or replaced on a weekly basis. To clean or replace the Air Filters, unscrew and remove the Wing Nut (36) on the Air Filter Cap (37). Remove the Air Filter

Cap, Air Filter, and Air Filter Bowl (39). Clean the Air Filter with compressed air or, if necessary, replace the old Air Filter with a new Air Filter. Clean the Air Filter Cap and Air Filter Bowl with a mild solvent and then dry. Then, replace the Air Filter

Bowl, Air Filter, Air Filter Cap, and Wing Nut. Repeat these procedures for the remaining Air Filter.

(See Figure G.)

CLiP

(34)

CLiP

(34)

CLiP

(34)

OuTER GuARd

SCREEN

(25)

LARGE bELT WHEEL

V-bELT

(27)

MOTOR

PuLLEY (14)

NuT (24)

FLAT WASHER (23)

NuT (24)

FLAT WASHER (23)

FiGuRE H

6. To replace the V-belt: The Air Compressor is equipped with a V-Belt (size: A1168

Li). To replace the V-Belt, remove the four Nuts (24) and four Flat Washers (23) on the Outer Guard Screen (25). Next, remove the three Clips (34) located at the top of the Outer Guard Screen. Then, remove the Outer Guard Screen.

(See Figure H.)

SKU 92504 For technical questions, please call 1-800-444-3353. Page 13

SidE ViEW ENd ViEW

SCREW

(30)

SCREW

(30)

SCREW

(30)

FiGuRE i

7. Loosen the four Screws (30) that hold the Motor (14) in place. Then, slide the Motor toward the Large Belt Wheel to loosen the tension on the V-Belt (27).

(See Figures H and i.)

8.

9.

Remove the loose V-Belt (27) from the Large Belt Wheel and Motor Pulley (14).

(See Figure H.)

Install a new V-Belt (27) on the Large Belt Wheel and Motor Pulley (14).

(See Figure H.)

3/4”

LARGE bELT WHEEL

FiGuRE J

V-bELT

(27)

MOTOR PuLLEY

(14)

10. Slide the Motor (14) back toward its original position to tighten the tension on the

V-Belt (27). NOTE: To determine the proper tension on the V-Belt, with your index finger press down on the V-Belt. The V-Belt should deflect downward about 3/4”.

If necessary move the Motor Pulley (14) toward or away from the Large Belt Wheel until the V-Belt deflects downward 3/4”. Then, retighten the four Screws (3) to secure the Motor (14) in place.

(See Figures i and J.)

SKU 92504 For technical questions, please call 1-800-444-3353. Page 14

11.

12.

To clean,

use a shop vacuum cleaner, or use compressed air.

When storing,

make sure to keep the Air Compressor in a safe, clean, and dry location out of reach of children.

13.

CAuTiON! All maintenance, service, or repairs not listed in this manual are only to be attempted by a qualified service technician.

LiMiTEd 1 YEAR / 90 dAY WARRANTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of one year from date of purchase that the tank is free of defects in materials and workmanship (90 days if used by a professional contractor or if used as rental equipment).

Harbor Freight Tools also warrants to the original purchaser, for a period of ninety days from date of purchase, that all other parts and components of the product are free from defects in materials and workmanship. This warranty does not apply to damage due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS ExPRESSLY IN LIEU OF

ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE WARRANTIES

OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

SKU 92504 For technical questions, please call 1-800-444-3353.

REV 08i

Page 15

PLEASE REAd THE FOLLOWiNG CAREFuLLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY

DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR

DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT

HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS

QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR

DISTRIBUTOR ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE

UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER

ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL

PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION

OF REPLACEMENT PARTS THERETO.

Part description

1 Flat Washer (8)

2 Screw (M8x16)

3 Safety Release Valve

4 Air Outlet Valve

5 Pressure Gauge

6 Pressure Adjustment Knob

7 Connector

8 Top Cover

9 Power Switch

10 Screw (M8x25)

11 Spring Washer (8)

12 Flat Washer (8)

13 Nut (M8)

14 Motor

15 Tube

16 Cap

17 Ring

18 Connector

19 No Return Valve

20 Exhaust

21 Bracket

PARTS LiST

qty.

1

1

8

1

8

8

1

4

1

1

1

1

1

2

1

2

1

1

2

4

4

Part description

22 Screw (M5x16)

23 Flat Washer (5)

24 Nut (M5)

25 Outer Guard Screen

26 Inner Guard Screen

27 V-Belt (A1168 Li)

28 Oil Fill Cap

29 Head Assembly

30 Screw (M8x16)

31 Power Cord

32 Air Tank

33 Tank Drain Valve

34 Clip

35 Oil Level Indicator

36 Wing Nut

37 Air Filter Cap

38 Air Filter

39 Air Filter Bowl

40 Oil Drain Plug

41 PCV Filter

42 Overload Reset Button

NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.

qty.

2

2

3

1

1

1

1

1

1

1

2

2

1

1

1

1

1

5

1

5

5

SKU 92504 For technical questions, please call 1-800-444-3353. Page 16

ASSEMbLY diAGRAM

34

23/24

14

10/11/12/13

17

18

16

20

19

27

15

8

9

7 6

5

4

3

1

2

25

26

21/22/23/24

35 36/37/38/39

40

28/41

29

30

11/12/13

31

32

33

NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.

SKU 92504 For technical questions, please call 1-800-444-3353. Page 17

WiRiNG diAGRAM

SKU 92504 For technical questions, please call 1-800-444-3353.

REV 06e

Page 18