OK2484 U3795HHS XL Signature
Powerful, Lightweight
Upright Vacuum
User’s
Guide
UK MODEL: U3795HHS
Important!
Read all instructions carefully, and keep for future reference.
E
Safety
N
G
L
I
S
H
General Warnings
IMPORTANT SAFETY INSTRUCTIONS!
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
• Do not leave appliance unattended when plugged in. Unplug from socket when not in use and before
servicing.
• Do not use outdoors or on wet surfaces.
• Do not operate the unit while in the upright and locked position.
• Do not let the unit run while in any one stationary position for any period of time. Keep the unit
moving while in operation.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities or lack of experience or knowledge. They should be given
supervision and instruction in the use of the appliance by a person responsible for their safety.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped,
damaged, left outdoors, or dropped into water, return it to an Oreck Approved Service Centre or call
Customer Care on: 0845 603 0153.
• Do not pull or carry by cord, use cord as a handle, close door on cord, or pull cord around sharp
edges or corners.
• Keep cord away from heated surfaces.
• Do not run appliance over cord.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint,
• Do not use to pick up anything that is burning or smoking, such as cigarettes, matches, or hot ash.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
where they may be present.
losive or toxic vapours are given off by
oil based paint, paint thinner, some mothproofing substances, or in an area where flammable dust is present.
• Do not pick up toxic material such as chlorine bleach, drain cleaner, petrol, etc. with this appliance.
• Use caution when vacuuming over rug edges and fringe.
SAVE THESE INSTRUCTIONS
Household Use Only
The wires in this mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your
plug, proceed as follows;
The wire which is coloured Blue must be connected to the terminal which
is marked with the letter N or coloured Black.
The wire which is coloured Brown must be connected to the terminal
which is marked with the letter L or coloured Red.
Neither wire is to be connected to the earth pin of the 3 pin plug.
Replace fuse with fuse of same ampage.
2
E
Contents
Total Cleaning System
Operation
N
G
L
I
S
H
Safety................................................................................................................................... 2
General Warnings ............................................................................................................ 2
Operation ............................................................................................................................. 3
Parts List .......................................................................................................................... 3
Assembling the Appliance .............................................................................................. 4
Operating the Vacuum...................................................................................................... 4
Operating Instructions .................................................................................................... 4
General Information ............................................................................................................. 5
Disposable Dust Bags ...................................................................................................... 5
Celoc® Filtration System .................................................................................................. 5
The Belt ........................................................................................................................... 5
Lubrication....................................................................................................................... 5
Maintenance ........................................................................................................................ 6
Replacing Disposable Dust Bag ..................................................................................... 6
Replacing Worn Belt ........................................................................................................ 6
Adjusting or Replacing Brushroll .................................................................................... 7
Replacing Edge Brushes .................................................................................................. 7
Using an Oreck Fresh Air® Scented Tablet ..................................................................... 7
Replacing Light Bulbs ..................................................................................................... 8
........................................................................................................ 8
Troubleshooting ................................................................................................................... 9
Parts .................................................................................................................................... 9
Replacement Parts ........................................................................................................... 9
Warranty .............................................................................................................................. 10
To assist you in identifying your vacuum’s components, the parts have been numbered
as follows: Parts List
1
1 Handle
2 On/Off Switch
3 Cord Hook
4 Handle Tube
5 Zip
6 Bumper
7 Edge Brush
8 Belt Door
9 Power Cord
10 Connector Deflector
Assembly
11 Collars
12 Lower Tube
13 Fan Housing
14 Bag Spring
15 Outer Bag
16 Power Head
17 Disposable Filter Dust Bag
18 Fascia
19 Housing
20 Cord Strain Relief Assembly
21 Harness
22 O-Ring
3
2
5
4
10
20
17
15
11
12
9
22
21
13
14
18
19
6
16
3
7
8
E
Operation
N
G
L
I
S
H
Assembling the Appliance
1
Before assembling appliance, remove two screws from the Connector Assembly. Remove
plastic insert by pulling upward.
2
Slide upper handle section over the matching section of the Connector Assembly. Hold tab of
TOP hole in Connector Assembly. Insert screw through hole in
2.1
3
Loop the Power Cord through the Strain Relief Kit as illustrated.
Take hold of the Harness (21 on parts list pg 3) - and push it into the clip located on the left
2
1
3
2.1
Operating the vacuum
Make sure the disposable dust bag is in place. DO NOToperate the cleaner without a dust bag.
Plug the power cord into an electrical socket and press the On ( l ) - OFF ( O )switch on handle
assembly when ready to operate.
4
5
Up-Position Lock -Place foot on power head and lean handle back gently to release lock for
vacuum use. Return handle to the full upright position to engage lock. Note: Do not operate the
unit while in the upright and locked position. Do not let the unit run while in any one stationary
position for any period of time. Keep the unit moving while in operation.
Easy Power Cord Storage - Wrap power cord around cord hook on handle and cord hook on
Connector Deflector Assembly.
Operating Instructions
4
5
You’ll love the way your Oreck cleans under things and is SO lightweight and easy to use.
The following are a few simple suggestions regarding its operation:
1. When inserting a new disposable dust bag - FIRST PUFF OUT and OPEN THE BAG.
2. When the disposable dust bag is full, REPLACE IT.
3. If at any time the machine does not pick up properly or makes an unusual noise, STOP OPERATION and service.
4. Although your upright will pick up pins, paper clips, and other small objects, it is recommended that these
motor suction fan and its housing.
5. WARNING: Do not use your vacuum cleaner on damp or wet surfaces. This will cause damage to the
vacuum cleaner and is dangerous to the user. Damage caused by use on wet or damp surfaces is not
covered under warranty.
6. For optimal performance, replace the belt every 6 months.
8. DO NOT run the vacuum cleaner over the cord. The revolving brush could damage the cord.
9. Use caution when vacuuming over area rug edges and fringe.
4
E
General
Information
N
G
L
I
S
H
The performance of your new cleaner greatly depends upon care and maintenance. The instructions
in this manual will guide you in performing basic care and maintenance. To obtain the most
satisfying years of service read the instructions and keep them handy for future reference.
Disposable Dust Bags
The purpose of the dust bag is to trap dirt, but at the same time it must be porous enough to allow
air to pass through. If the dust bag becomes clogged, no air can pass through the cleaner and
cleaning cannot take place, regardless of the cleaner’s power.
.
DO NOT FILL ABOVE THE LINE INDICATED ON THE DUST BAG.
not the same. Your ORECK disposable dust bags have been designed to be used with the ORECK
cleaner. Using bags other than genuine ORECK TYPE CC disposable bags will affect the cleaning
ability of your cleaner and could cause damage to it and will void the warranty.
Celoc®Filtration System
smallest of dust particles. It is important that the inside of the outer bag be cleaned. Vacuum the inside
of the outer bag or hand wash, turned inside out, with warm water, and air dry. If desired, the Celoc®
replaced once a month even if it is not full. Change it more often if it is used in extremely dirty areas.
Increase the cleaning power of your vacuum by changing the bag often.
The Belt
The belt on your vacuum cleaner controls the speed of the revolving brush and is very important
for the effective operation of the cleaner. If the belt becomes stretched or cut, it will cause the
revolving brush to stop completely or slow down. See page 6 for replacing worn belt.
Note:An extra belt is stored in the baseplate of your cleaner. When buying replacement belts, use
ONLY ORECK genuine belts. Belts other than Oreck belts will not operate the revolving brush
correctly and may create undue stress which will cause damage to the motor and brush bearings.
Using belts other than ORECK belts will void the warranty.
Lubrication
The vacuum cleaner motor bearings are factory lubricated and sealed. Further lubrication is not required.
CAUTION
Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor Surfaces and Polished
Floor Finishes
operate the unit while in the upright and locked position. Do not let
the unit run while in any one stationary position for any period of
time. Keep the unit moving while in operation.
Note: At least once a month, check for and remove excessive lint,
string or hair from revolving brush.
WARNING: Unplug cord from electrical socket before servicing.
Wipe the outside of the cleaner with a damp cloth. Also clean the Connector
Deflector Assembly area, base of cleaner and Fan Housing area. If there is
dust in the outer bag, vacuum it or shake it out.
A little preventative maintenance will keep your cleaner looking new
and will ensure continued cleaning effectiveness.
5
E
Maintenance
N
G
L
I
S
H
Replacing Disposable Dust Bag
WARNING:
Unplug cord from electrical socket before servicing.
BAG REMOVAL:
6
Unzip outer bag completely.
7
Pull bag cardboard collar to release bag dock door from connector. Bag dock door will
hinge downward.
8
Gently pull bag cardboard collar upward out of the bag dock. Saniseal®dust seal will
close automatically.
BAG INSTALLATION:
Slide the cardboard collar completely onto bag dock door.
10 Firmly push bag dock door with both thumbs on indication point until it snaps.
9
PRESS
UNTIL SNAP
IS HEARD
6
7
8
8
10
Replacing Worn Belt
WARNING:
Unplug cord from electrical socket before servicing.
11
12
13
14
15
13
12
Remove the replacement belt from the storage channel on the vacuum base.
Remove the belt door by removing the Phillips screw located on side of power head.
Fold door away from the power head and lift it away.
Remove the belt from the motor drive shaft and brushroll pulley .
Loop the new belt over the brushroll pulley. Stretch the opposite end of the belt on to the motor
drive shaft.
Replace the door by placing the bottom tab on door into slots located inside power head and
pressing the door closed.
Replace the Phillips screw and tighten.
11
12
13
6
14
15
E
G
L
I
S
H
Adjusting or Replacing Brushroll
WARNING:
Unplug cord from electrical socket before servicing.
To determine if the brushroll is worn, place a firm object with a straight edge across the opening
in the base of the vacuum. If the brushroll bristles do not extend evenly beyond the baseplate and
touch the straight object then the brushroll should be adjusted.
16
17
Remove the baseplate by removing 5 screws and then remove the belt and brushroll from the housing.
18
19
To adjust the brushroll, rotate the ends of each brushroll so that the ‘OLD’ setting is uppermost (19).
The ‘OLD’ setting is smooth and has no grooves along the edge. The ‘NEW’ setting. has several
grooves along the edge (18) and on a new brushroll this should be facing uppermost.
Note: Only one of the brushroll ends has 'OLD' and 'NEW' setting positions marked,
as indicated in illustrations 18 and 19.
15
16
Reassemble the belt.
Reassemble the baseplate.
If a previous adjustment has already been made and bristle height does not extend above the
baseplate, a new brush assembly should be ordered or a Service Kit (SERKIT35G).
IMPORTANT: Both brushroll ends must be set to the same setting. The right and left side
must be both 'NEW' or both 'OLD'. Unmatched settings can cause damage to the unit.
Brushroll End Position
for a NEW brushroll
Brushroll End Position
for an OLD brushroll
NEW
OLD
NEW
17
16
OLD
Maintenance
N
18
19
Replacing Edge Brushes
WARNING:
Unplug cord from electrical socket before servicing.
Turn the power head over. With baseplate facing up, remove the 5 recessed screws. Once removed,
turn over the baseplate to see the edge brushes, each secured with a single screw. Remove both edge
brushes and replace with the new ones. Reassemble baseplate.
Using an Oreck Fresh Air® Scented Tablet
Using ORECK XL vacuum cleaner has a special Oreck Fresh Air® Scented Tablet pocket.
This pocket is located inside the outer cloth bag in the area where the disposable dustbag attaches
to the intake tube. Insert tablet in pocket if desired.
7
E
Maintenance
N
G
L
I
S
H
Replacing Light Bulbs
WARNING: Unplug cord from
electrical socket before servicing.
16
Remove the baseplate by removing 5 screws.
20
Remove the belt from the brushroll pulley. Then, remove the brushroll from the housing.
21
Remove the fascia by removing 2 screws.
22
Rotate fascia away from the power head and lift it away.
23
Pull burned out bulb from holder and replace with new bulb.
22
Reassemble the fascia.
20
Reassemble the brushroll and belt.
16
Reassemble the baseplate.
20
21
22
23
Stuffing or Blockage
IMPORTANT:
ube and the lower tube
few cleanings until all the loose material is removed. Due to t
m. If your vacuum cleaner does not pick up
WARNING:
Unplug cord from electrical socket before servicing.
Check for blockage at the mouth of the intake opening. If there is blockage, remove it with longnose pliers, a screwdriver or coat hanger. If you cannot reach the blockage, remove baseplate.
Remove the baseplate by removing 5 screws (see “Adjusting or Replacing Brushroll”).
25 If the blockage is not at the base, remove lower tube. Unhook bag spring, releasing bottom of bag.
26 Twist lower collar counterclockwise to slide up. Pull tube out of base.
27 Check for blockage. If blockage is in the tube, remove with a coat hanger.
24
28
If tube is not blocked, look into Fan Housing. Remove debris with long-nose pliers, a
screwdriver or coat hanger.
26
at base of tube with tab inside Fan Housing. Insert tube and push down until the tube is seated.
Make sure O-ring is in place against Fan Housing opening. Replace and tighten collar until
collar locking tabs are locked in place. Reattach bag spring.
29 Many times blockage occurs due to a full dust bag causing dirt
When that happens, the blockage will be at the top of the system, starting in the area where the
dust bag connects to the Connector Deflector Assembly.
Note: If the above actions do not correct the problem, contact an Oreck Approved Service
Centre or call Customer Care on 0845 603 0153.
24
25
26
8
27
28
29
E
Troubleshooting
N
G
L
I
S
H
Service problems that appear to be major can often be solved easily. You can be your own
troubleshooter by reviewing this guide.
Problem
Check
Cleaner will not
run.
What to do
• Not plugged in properly.
• No electricity in wall
outlet.
• Filter Bag is full.
• Nozzle or intake
clogged.
• Belt is broken or
stretched.
Cleaner does not
pick up.
• Replace belt.
• Brush is worn.
• See “Adjusting or Replacing Brushroll”
page 7.
• Bag tube clogged.
• Clear obstruction. See “Stuffing or
Blockage” page 8.
• Bag pores are clogged
• Change bag.
• Revolving brush not
even at each end.
• Check that the brushroll is aligned
correctly. See “Adjusting or Replacing
Brushroll” page 7.
Unit still does not
operate properly.
Parts
socket.
• Check electrical source – fuse or circuit
breaker.
• Replace Filter Bag. See “Replacing
Disposable Dust Bag” page 6.
• Clear obstruction. See “Stuffing or
Blockage” page 8.
• Contact Oreck for service.
All other servicing should be done by an Oreck Approved Service Centre.
All accessories and replacement parts are sold separately. To order, call Customer Care on
0845 603 0153 or visit our website www.oreck.co.uk. Please have your model number
from the data label on the bottom of the unit.
Accessories
Item
Part Number
Crystal Aroma Carpet and Room Freshener
Oreck Dry Carpet®Cleaning System
Service Kit
Fresh Air Scented Tablets
®
CRYSTAL
CARPETCSYS
SERKIT35G
AIRTABS
Replacement Parts
Item
Part Number
Dust Bag, 8 Pack, Saniseal®Hypo-Allergenic
Belts, 3 Pack
Dust Bags, 8 Pack, HEPA Odour Fighting
9
PK20008DW
3BELTS
CCPK8OH
E
Warranty
N
G
L
I
S
H
ORECK MANUFACTURING COMPANY: (Oreck, 1400 Salem Road, Cookeville, TN, USA
38506) gives you the following warranty for this product only if it was originally purchased for
residential use, not resale, from Oreck or an Oreck Approved Retailer.
Oreck will repair or replace, free of charge, to the original purchaser, any part that is found to
be defective in material or workmanship within three (3) years of date of purchase; ten (10)
years on housing. This limited warranty applies to normal domestic use. Any commercial use of this
product will void this warranty. This limited warranty covers the revolving roller brush for one
(1) year for residential use only.
This limited warranty does not cover the replacement of expendable or consumable parts such as
edge brushes, belts, bulbs, disposable bags and other parts subject to normal wear unless they
are defective in material or workmanship.
Total Cleaning System
This limited warranty does not cover use of non-original Oreck parts, including (but not
limited to) bags, belts, filters and spares, which will invalidate the warranty.
This limited warranty does not apply to any part subjected to accident, abuse, alteration,
misuse, damage caused by act of God, the use of voltages other than indicated on the serial
number displayed on this product or service of this product by other than Oreck or a participating
Oreck Approved Service Centre.
Oreck does not authorise any person or representative to assume or grant any other warranty obligation with the sale of this product.
Oreck’s limited warranty is valid only if you retain proof of purchase from Oreck or an Oreck
Approved Retailer for this product. If you purchase this product from any other source, your
purchase is “AS IS,” which means Oreck grants you no warranty, and that you, not Oreck, assume
the entire risk of the quality and performance of this product, including the entire cost of any necessary servicing or repairs of any defects.
Oreck’s liability for damages to you for any costs whatsoever arising out of this statement of
limited warranty shall be limited to the amount paid for this product at the time of original
purchase, and Oreck shall not be liable for any direct, indirect, consequential or incidental
damages arising out of the use or inability to use this product.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT, INCLUDING
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD, AND NO
WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THIS
PERIOD.
This limited warranty is in addition to your statutory and other legal rights.
Reconditioned units carry a 12 month warranty from date of purchase.
UK & EIRE DISTRIBUTOR:
Integrity (Europe) Ltd, 32 Marsh Green Road West, Marsh Barton, Exeter, EX2 8PN
10
11
OK2484
76137-01 REV A 03/11
R-10419
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement