SonusTM - Evenflo
SonusTM
Child Restraint System
Owner’s Manual
Keep for future use.
See back cover to remove Owner’s Manual.
Rear-facing*
2.3 to 18 kg
(5 to 40 lbs)
48 to 102 cm
(19 to 40 in.)
Forward-facing*
10 to 22.6 kg
(22 to 50 lbs)
71 to 127 cm
(28 to 50 in.)
At least 2 years old
* See inside cover for complete requirements.
Para instrucciones en Español,
llamar al: 1-800-233-5921
WARNING:
To reduce the risk of serious injury
or death, read this owner’s manual prior
to installing and using this child restraint.
© 2016 Evenflo Company, Inc.
25700676
8/16
Important
Premature Infant Use..................................................2
Warnings....................................................................3
LATCH Warnings ........................................................7
Safe Practices .............................................................9
Recall Information for U.S. Customers ......................10
Public Notice for Canadian Customers .....................10
Motor Vehicle/Aircraft Usage ...................................10
Symbol Legend ........................................................11
Storing Your Instructions ..........................................11
Visual Glossary .........................................................12
Child Restraint Features ............................................14
Rear-facing Use
Rear-facing Installation Checklist ..............................17
Rear-facing Installation with
Lower Anchor Connectors .....................................18
Rear-facing Installation with Seat Belt .......................22
Forward-facing Use
Forward-facing Installation Checklist ........................27
Forward-facing Installation with
Lower Anchor Connectors .................................... 28
Forward-facing Installation with Seat Belt ................ 32
Rear-facing
• No restraint can guarantee absolute protection from
injury in every crash.
• This child restraint is designed for use by children in rearfacing and forward-facing positions. To use this child restraint
properly, children MUST meet weight/size specifications as
follows:
For Rear-facing Use
• 2.3 to 18 kg (5 to 40 lbs)
• 48 to 102 cm (19 to 40 inches)
• Top of head is at least 25 mm (1 inch) below
the top of the child restraint seat back.
The American Academy of Pediatrics recommends that
children ride in the rear-facing position to the highest weight
or height allowed by the child restraint. A rear-facing car
seat provides support for a child’s head, neck and spine in
frontal collisions, which are the most common type of crash.
Additionally, many states have updated their laws to reflect
this AAP recommendation. Please review any applicable local,
state or provincial laws related to child passenger safety before
installing and using this child restraint.
Note: Once your child exceeds any of the three
requirements above, they MUST use the child restraint in
the forward-facing position.
For Forward-facing Use
• 10 to 22.6 kg (22 to 50 lbs)
• 71 to 127 cm (28 to 50 inches) AND the tops of the child’s
ears are at or below the child restraint seat back.
• At least two years of age
Note: Once your child exceeds 22.6 kg (50 lbs) OR 127 cm
(50 inches) OR the top of their ears are above the top of
the child restraint seat back, they can no longer safely
use this child restraint, and you should consider using a
booster seat.
Important Information
General Information
Positioning the Harness Strap ...................................36
Adjusting the Recline Stand ......................................38
Securing the Child in the Child Restraint ..................39
Adjusting the Crotch Strap .......................................40
Adjusting the Harness Strap .....................................41
Removing the Child from the Child Restraint............42
Removing the Tether Strap .......................................42
Removing the Lower Anchor Connectors .................44
Installing the Accessories ..........................................45
Securing Your Child Restraint in Aircraft ...................46
Installing Child Restraint Rear-facing in Aircraft.........46
Installing Child Restraint Forward-facing in Aircraft...49
Care and Cleaning ...................................................51
Replacement Parts ....................................................52
Limited Warranty......................................................53
U.S. REGULATORY NOTICE
This child restraint meets all applicable requirements of
Federal Motor Vehicle Safety Standard 213.
Forward-facing
Child Requirements
Table of Contents
General
More children are killed every year as passengers
in car crashes than by any other type of injury.
To reduce the risk of SERIOUS INJURY or DEATH, read this owner’s
manual and your vehicle owner’s manual before installing and using this
child restraint. Using a child restraint makes a big difference. By properly
using this child restraint and following these instructions (and the
instructions that accompany your vehicle), you will greatly reduce the risk
of serious injury or death to your child from a crash. Do not be misled by
the commonly used term “safety seat”; no restraint system can prevent
all injuries in all crashes. Many properly restrained adults and children
are injured in motor vehicle crashes, including relatively minor crashes. A
properly used child restraint is the best way to minimize injuries to your
child and to increase the chances for your child’s survival in most crashes.
CANADIAN REGULATORY NOTICE
(Model numbers ending in “C.”)
This child restraint meets all applicable requirements of
Canadian Motor Vehicle Safety Standards CMVSS 213
and 213.1.
1
2
WARNING
Air Bag Warnings
• DO NOT use this child restraint in the front seat of a
vehicle equipped with an air bag, unless the air bag
has been deactivated. Air bags may cause serious
injury or death to children under 12. If your vehicle
has an air bag, please refer to your vehicle owner’s
manual for child restraint installation.
• If the rear seat of your vehicle is equipped with side air
bags, refer to the following information for proper usage:
Vehicles built prior to the 2002 model year:
DO NOT use this restraint in a vehicle seating position
equipped with a side air bag unless authorized by the
vehicle manufacturer.
Model year 2002 and newer vehicles: Refer
to your vehicle owner’s manual before placing this
restraint in a seating position equipped with a side air
bag. DO NOT place any objects between the restraint
and the side air bag, as an expanding air bag may
cause the items to strike your child.
Important
PREMATURE INFANT USE
Before using this child restraint for preterm or low birth
weight infants you must read and follow the guidelines in
this section.
According to the U.S. National Highway Traffic Safety
Administration, a properly installed child restraint
reduces the risk of death by over 70 percent for infants
involved in crashes. Federal Motor Vehicle Safety
Standard (FMVSS) 213 establishes design and dynamic
performance requirements for child restraint systems.
However, the standard has no minimum weight limit
and does not address the special medical needs of
preterm or low-birth weight infants. To ensure that
preterm and low-birth weight infants are transported
safely, the guidelines published by the American
Academy of Pediatrics (AAP) in Pediatrics 2009; 123:
1424–1429 must be followed.
All children should ride rear-facing in the vehicle as
long as possible. Preterm and low-birth weight infants
are at additional risk of breathing difficulties and heart
problems when placed in a child restraint. Evenflo
requires that the evaluation recommended by the AAP
be conducted for all infants born earlier than 37 weeks
and all newborn infants who weigh less than 5 pounds
at birth before their first car trip to check for breathing
difficulties or heart rate problems when traveling in a
rear-facing child restraint.
The AAP recommends that appropriate hospital staff
observe your infant in the child restraint for a period of
90 to 120 minutes or the duration of travel, whichever
is longer. This period of observation must be performed
with the infant properly positioned as described in these
instructions and with the child restraint placed at an
angle that is approved for use in the vehicle. The
hospital staff will check for any breathing difficulties or
heart rate problems. Your child’s pediatrician will let you
know if there are any special considerations for travel.
The number of trips and the duration of time the infant
is seated in the child restraint should be minimized. A
caregiver should ride in the back seat to monitor the
infant during travel.
You can learn more about the AAP’s recommendations
for observation of newborns and the guidelines for safe
transportation of preterm and low-birth weight infants,
as well as other resources for parents and medical
professionals, at
https://www.healthychildren.org/english/safety-prevention/on-the-go/Pages/default.aspx
The forward-facing rear seat is the
safest place for children 12 and under.
3
WARNING
General Warnings
Location Warnings – continued
Rear-facing and Forward-facing Use
• Failure to follow installation instructions can result in
the child striking the vehicle’s interior during a sudden
stop or crash. Serious injury or death may result.
These instructions and the instructions in your vehicle
owner’s manual must be followed carefully. If there is a
conflict between the two, the vehicle owner’s manual
regarding child restraint installation must be followed.
• NEVER leave child unattended.
• Children have STRANGLED in loose or partially
buckled harness straps. Fully restrain the child.
Rear-facing and Forward-facing Use
• ONLY use this child restraint on vehicle seats with
backs that lock into place.
WARNING
Children have STRANGLED
in loose or partially buckled
harness straps. Fully restrain
the child.
• DO NOT use child restraint if it is damaged, broken,
or missing parts.
• DO NOT use this restraint if it has been involved in a
crash. It must be replaced.
Location Warnings
Rear-facing and Forward-facing Use
• ALWAYS read and follow exactly the instructions that
accompany your vehicle and child restraint.
• According to statistics, children are safer when properly
restrained in a rear seating position than in the front
seating position. Generally, the center rear position is
safest and should be used if available.
• Some child restraints do not fit all vehicles or all seating
locations. There are many thousands of combinations
of vehicle makes, models, child restraint configurations,
vehicle seat belt designs, and seat cushion shapes. The
easiest way to determine whether your child restraint
is suitable for a particular seating position is to check
for a tight installation. If the child restraint cannot be
properly installed, DO NOT use the child restraint.
Consult vehicle owner’s manual, try a different seating
location, or call Evenflo for further assistance.
• ONLY use this child restraint on forward-facing
vehicle seats. DO NOT use this restraint with
vehicle seats that face the rear or side.
4
Premature Infants
Rear-facing Use Only
Important
WARNING
• DO NOT use this or any child restraint with a
premature infant until after consulting your doctor.
Premature infants may have difficulty breathing when
in a seated or semi-reclined position. Using additional
padding or pillows behind the infant’s head or failing
to properly recline the child restraint could increase
the child’s risk of serious injury or death.
Rear-facing Only Warnings
• When using this restraint rear-facing, DO NOT loosen
the vehicle seat belt to provide more leg room, as this
will prevent the child restraint from protecting the
child.
• DO NOT use the highest set of harness slots rearfacing. The harness will not properly restrain the child
during a crash.
• Fold-down armrests could pose a hazard to a
rear-facing child in certain types of collisions. Consult
your vehicle owner’s manual before installing any rearfacing child restraint in front of a fold-down armrest.
• NEVER turn a child restraint forward-facing with a
child who weighs less than 10 kg (22 lbs). Crash forces
may cause serious injury or death.
• DO NOT use the tether strap when the child restraint
is in the rear-facing position.
• The headrest on the vehicle seat that the child faces
when sitting in the rear-facing mode should be placed
in the lowest position. The vehicle seat back that the
child faces must be fully padded and free of any hard
objects.
Forward-facing Only Warnings
• If your child weighs more than 22.6 kg (50 lbs) or their
shoulders are above the highest harness level, you
MUST discontinue using this child restraint as it may
no longer adequately protect your child.
• MUST be at least two years of age.
5
Forward-facing Only Warnings – continued
• DO NOT use the lowest set of harness slots
forward-facing. The harness will not properly restrain
the child during a crash.
• Adjust, or remove, the vehicle headrest in the
seat where the child restraint is to be installed,
so that the back of the child restraint rests against the
vehicle seat back.
• The headrest on the vehicle seat in front of the child
should be put in its lowest position. The vehicle seat
back that the child faces must be fully padded and
free of any hard objects.
Seat Belt Warnings
Rear-facing and Forward-facing Use
• DO NOT use this child restraint if it moves more than
25 mm (1 inch) side to side or front to back at either
the rear-facing or forward-facing belt path on the
child restraint. Serious injury or death may result from
poor installation. If you cannot tightly secure the child
restraint, try again or move it to another location.
• DO NOT use this child restraint in a seating position
with door-mounted seat belts.
• DO NOT use this child restraint in a vehicle with seat
belts that automatically move along the vehicle frame
when the door is opened. These seat belts will not
hold a child restraint properly.
• DO NOT use this child restraint in a vehicle equipped
with lap belts that only lock during a sudden stop or
crash (emergency locking retractor – ELR). You must
use a seating location with a locking seat belt. Check
your vehicle owner’s manual to see if you have lap
belts with ELRs.
• If the vehicle seat belts are not routed and fastened
correctly, the child restraint may not protect the child
in a crash.
• DO NOT allow the vehicle seat belt release button to
touch the child restraint. Accidental contact may cause
the seat belt to release. If necessary, turn the seat belt
release button away from the child restraint or move
the child restraint to a different location.
• Failure to adjust the harness or vehicle seat belts
snugly around the child may result in the child striking
the vehicle’s interior during a sudden stop or crash.
Serious injury or death may occur.
6
WARNING
LATCH Warnings
Rear-facing and Forward-facing Use
• The LATCH system is intended to be used ONLY as
described in these instructions. Serious injury or death
may result from misuse. LATCH (Lower Anchors and
Tethers for CHildren) is a system for attaching the
child restraint to your vehicle seat. It can be used in
place of the seat belts in vehicles with vehicle lower
anchor bars. Refer to your vehicle owner’s manual for
the locations of the vehicle lower anchor bars. Note:
Your vehicle owner’s manual may refer to this system
as “Universal Anchorage System,” “Lower Universal
Anchorage System,”or ”ISOFIX.”
• In addition to these instructions, read and follow your
vehicle owner’s manual regarding installation of the
child restraint and LATCH. If there is a discrepancy,
follow your vehicle owner’s manual.
• ONLY use for securing child restraint to vehicle lower
anchor bars.
• NEVER attach two lower anchor connectors to one
vehicle lower anchor bar.
• NEVER use the vehicle seat belts when using the
Lower anchor connector assembly. Using both
together can cause slack in a sudden stop or crash.
• To avoid strangulation, you must store the unused
LATCH harness, with all slack removed, in the storage
area on the bottom of the seat. Roll or fold the excess
LATCH strap and secure with a rubber band to prevent
serious injury to vehicle occupants.
• ALWAYS be sure that the lower anchor connectors
are attached to the vehicle lower anchor bars by
pulling hard on the lower anchor connectors. If
they are not attached, the lower anchor connector
assembly will not secure your child restraint. Serious
injury or death may result.
• DO NOT use this child restraint if it moves more than
25 mm (1 inch) side to side or front to back at either
the rear-facing or forward-facing belt path on the
child restraint. Serious injury or death may result from
poor installation. If you cannot tightly secure the child
restraint, try again or move it to another location.
Important
WARNING
7
Tether Strap Warnings
Forward-facing Use Only
• To avoid a strangulation hazard, you MUST tightly roll
or fold excess or unused tether strap and secure with
a rubber band. Attach the tether hook to the storage
clip when not in use (p. 14). This will keep an unused
tether from hitting someone during a crash.
Additional Warnings
Rear-facing and Forward-facing Use
• In hot or sunny weather, ALWAYS check the areas of
the child restraint that may contact your child (e.g.,
buckle, buckle tongues, etc.) for hot areas before
placing him/her into the child restraint. The child
could be burned. Cover the child restraint with a light
colored blanket when you leave the vehicle.
• This child restraint must be securely fastened to the
vehicle, even when unoccupied, using the vehicle
seat belts or lower anchor connectors. An unsecured
child restraint may injure someone if a crash occurs.
• DO NOT use the cup holder to store cans or hard
cups. Only for use with soft cups (such as styrofoam
or paper).
• DO NOT place any cups that contain hot liquids
in the cup holder.
• DO NOT attach additional padding, toys, or other
devices not made by Evenflo or described in these
instructions for the child restraint. Items not tested
with the child restraint could injure the child.
Additional pads or pillows may interfere with the
function of the harness system, or cause breathing
problems if the child’s head falls forward, increasing
the risk of serious injury or death.
• Failure to follow installation instructions could result
in serious injury or death. These instructions and the
instructions in your vehicle owner’s manual must be
followed carefully. If there is a conflict between the
two, the vehicle owner’s manual regarding child
restraint installation must be followed.
8
WARNING
Additional Warnings– cont.
• In cold weather, DO NOT dress the child in bulky
clothing like snowsuits if the child is riding in a child
restraint. Bulky coats/snowsuits make it difficult to
properly tighten the harness to the child, which may
allow the child to be ejected from the restraint during
a crash. If necessary, place a blanket over the harnessed
child without interfering with the child restraint
harness system.
Important
WARNING
Safe Practices
• Everyone rides buckled up or the vehicle does
not go. Make no exceptions for adults or children. If
someone unbuckles, stop the vehicle. Being firm and
consistent from the start will mean fewer discipline
problems as children get older. An unrestrained person
can be thrown into and injure other passengers.
• Many safety advocates and healthcare professionals
recommend that children ride rear-facing for as long
as possible. See limitations recommended on rearfacing use on the inside front cover.
• NEVER try to tend to a crying baby’s needs while
driving. NEVER take a baby out of a child restraint for
comforting while the vehicle is moving.
• DO NOT allow a child in a vehicle to have objects
such as lollipops or ice cream on a stick. The object
can injure the child if the vehicle swerves or hits a
bump.
• DO NOT feed an infant who is riding in a child
restraint.
• Put sharp or heavy items in the trunk. Anything loose
can be deadly in a crash.
9
Recall Information for U.S. Customers
Storing Your Instructions
After thoroughly reading and following these instructions,
use the plastic lanyard A to store the instructions on
either side of the child restraint. You may also store the
instructions behind the seat pad.
So
Childnus™
Rest
rain
ne
t Sy
p for r’s M
stem
Ow
Kee
future an
ual
Rearuse
.
facing
2.3
(5 to to 18 kg
40
lbs)
48
(19 to 102 cm
to
For 40 in.)
wa
10 to rd-fac
ing
(22 22 .6
to 50 kg
to 127 lbs)
8 to
cm
50
in.)
)
A
cion
es
00- en Esp
233
-59 añol,
21.
NING
:
of serio
owne us injur
r’s man y
g this
child ual prior
restr
aint.
OR
y, Inc.
Rear-facing*
2.3 to 18 kg
(5 to 40 lbs)
48 to 102 cm
(19 to 40 in.)
Forward-facing*
When used with the internal
harness and properly installed
pursuant to these instructions,
this restraint is certified for use only
Check with
in passenger and multi-purpose
your airline before
passenger motor vehicles, buses,
departure to make sure
and trucks equipped with either
this restraint meets
lap belts only or lap/shoulder belt
their requirements.
systems and in aircraft.
10 to 22.6 kg
(22 to 50 lbs)
SonusTM
Motor Vehicle/Aircraft Usage
Owner’s Manual
Child Restraint System
y,
Keep for future use.
• For public notice information, call Transport Canada at
1-800-333-0510 (1-613-993-9851 in Ottawa region).
Important
Aircraft Symbol – Alerts you to important
information about aircraft safety.
WARNING:
• Child restraints could be recalled for safety reasons.
You must register this restraint to be reached in a
recall. Send your name, address, and the restraint’s
model number and manufacturing date to:
Evenflo Company, Inc.,
1801 Commerce Dr.,
Piqua, OH 45356
or call 1-937-773-3971.
or register online at:
www.evenflo.com/registercarseatcanada
Tether Anchor Symbol – Alerts you to
important information about Tether Anchor safety.
To reduce the risk of serious injury
or death, read this owner’s manual prior
to installing and using this child restraint.
Public Notice for Canadian Customers
LATCH Symbol – Alerts you to important
information about LATCH safety.
71 to 127 cm
(28 to 50 in.)
• For recall information, call the U.S. Government’s
Vehicle Safety Hotline at 1-888-327-4236
(TTY:1-800-424-9153), or go to: http://www.NHTSA.gov
Airbag Symbol – Alerts you to important
information about airbag safety.
* See page 1 for complete requirements.
Para instrucciones en Español,
llamar al: 1-800-233-5921
• Child restraints could be recalled for safety reasons.
You must register this restraint to be reached in a recall.
Send your name, address, e-mail address if available, and
the restraint’s model number and manufacturing date to:
Evenflo Company, Inc.,
1801 Commerce Dr.,
Piqua, OH 45356
or call 1-800-233-5921.
or register online at:
www.evenflo.com/registercarseat
Symbol Legend
TIP
IP!
Refer to pages 46 to 50 for instructions on installing your
child restraint in aircraft.
Manufactured in Fabriqué en
(year-month-day) (année-mois-jour)
Name / Nom
Model / Modèle
Made in / Fabriqué en
Expires on/Expire le
For future reference, record the model number of your
child restraint AND the date of manufacture below.
Model Number:
Date of Manufacture:
10
11
Visual Glossary
Visual Glossary
Headrests
Must be in the lowest
position where the child
restraint is located.
Fold-down Armrest
Consult your vehicle’s owners manual.
Tether Anchors
Forward-facing
ONLY
Back Seat
Belt Buckles
10
Center Lap
Belt
4
30
20
12
0
Back Seat
Retractor
Front Seat Lap and Shoulder Belts
Important
Your vehicle components may be significantly different than
pictured. Consult your owner’s manual to help you identify
your vehicle components.
A
IR
B
A
G
IMPORTANT
Lap/Shoulder
Belt
Lower
Vehicle
Anchor
Bars
Seat Crease
Front Seat Retractor
Consult your vehicle
owner’s manual to determine
proper placement of child restraint
in your vehicle and familiarize
yourself with your vehicle’s
components.
IMPORTANT: If your vehicle has side air bags, please refer to
the warnings on page 3.
12
13
Child Restraint Features
Child Restraint Features
1. Seat Pad
1
2. Head Pillow
2
3. Harness Straps
3
4
5
6
9
Important
Description
Front
4. Chest Clip
5. Buckle
10
6. Crotch Strap
7. Harness Release Button
8. Harness Adjust Strap
7
9. Buckle Tongue Holder*
10. Cup Holder*
8
11. Tether Strap and Hook (Shown fastened to storage clip)
12. Harness Straps
13. Splitter Plate
Back
14. Recline Stand
* Not all features are available on all models. Styles may vary.
11
12
13
14
14
15
Using the Child Restraint
Rear-facing
Child Requirements:
Rear-facing Installation Checklist
1. Secure child restraint to the vehicle seat.
• Recline stand is flipped to the recline position
(page 38).
25 mm (1 inch)
or more
Harness straps are
at, or slightly below
the child’s shoulders.
Rear-facing
Belt Path
Lower Anchor
Connector
Assembly
Note: Once your child exceeds 18 kg (40 lbs) OR
102 cm (40 inches) OR the top of their head is within
25 mm (1 inch) of the top of the child restraint seat
back, you MUST use this child restraint in the forwardfacing position.
(page 18) or vehicle seat belt (page 22).
• Towel rolled up and placed beneath the recline
stand, if necessary (page 38).
• Install locking clip, if necessary (page 24).
2. Set the child in the child restraint.
Top of head is at least 25 mm (1 inch) below the
top of the child restraint seat back.
3. Fasten the buckle. Refer to page 39.
4. Make necessary adjustments.
• Crotch strap is snug against the child (page 40).
• Harness straps MUST be snug against the child’s
shoulders, with no slack (page 39).
5. Position and connect chest clip.
Chest clip MUST be at armpit level (page 39).
6. Check your work.
• Recline stand is flipped to the recline position
•
•
•
•
•
Note: When in rear-facing position, bottom of child
restraint MUST be entirely on vehicle seat.
16
Rear-facing
• Weight: 2.3 to 18 kg (5 to 40 lbs)
• Height: 48 to 102 cm (19 to 40 inches) AND the top
of child’s head is at least 25 mm (1 inch) below top of
the child restraint seat back.
• Install with Lower Anchor Connector Assembly
(page 38).
To properly secure this child restraint it MUST NOT
move more than 25 mm (1 inch) from side to side
or front to back at the rear-facing belt path (pages
21 and 25).
The child’s back and bottom are flat against the
back and bottom surfaces of the child restraint
(page 39).
Shoulder harness straps MUST start at or below
shoulder height using the strap slots closest to your
child’s shoulders (page 36).
Buckle tongues are fully engaged (page 39).
The level arrow is level with the ground (pages 19
and 22).
WARNING
When using this restraint rear-facing, DO NOT loosen the
vehicle seat belt to provide more leg room, as this will
prevent the child restraint from protecting your child.
17
LATCH is a system for attaching the child restraint to your
vehicle seat. It is to be used in place of your vehicle’s seat
belts and can be used in vehicles with LATCH anchors. Your
vehicle owner’s manual may refer to this system as
ISOFIX, Universal Anchorage System (UAS), or Lower
Universal Anchorage System.
1
WARNING
NEVER turn a child restraint
forward-facing with a child
who weighs less than 10 kg (22 lbs).
Crash forces may cause serious
injury or death.
WARNING
• ONLY use for securing child restraint to lower anchor
bars.
• ALWAYS read and follow exactly the instructions which
accompany your vehicle and child restraint.
• NEVER attach two hooks to one vehicle lower anchor
bar.
• DO NOT use the vehicle seat belts to install a child
restraint when using the Lower Anchor Connector
Assembly.
• This Lower Anchor Connector Assembly is intended to be
used ONLY as described in these instructions.
Serious injury or death may result from misuse.
• ALWAYS be sure that the Lower Anchor Connector hook
is fully engaged onto the Vehicle Lower Anchor Bar by
pulling hard on the Lower Anchor Connector strap. If it is
not totally engaged, the Lower Anchor Connector
Assembly will not secure your child restraint. Serious
injury or death may result.
• To avoid a strangulation hazard, you MUST store the
unused lower anchor connector assembly, with all slack
removed, in storage area on the bottom of the seat
(page 45). Roll or fold excess lower anchor connector
strap and secure with a rubber band to prevent serious
injury to vehicle occupants.
• In addition to these instructions, read and follow your
vehicle owner’s manual regarding installation of child
restraints and LATCH. If there is a discrepancy, follow your
vehicle owner’s manual.
ARROW MUST BE LEVEL WITH
GROUND WHEN USED REAR-FACING
A
REAR OF VEHICLE
ARROW MUST BE LEVEL WITH
GROUND WHEN USED REAR-FACING
REAR OF VEHICLE
Infants MUST always ride
facing the rear of the vehicle.
The back of the child restraint supports and protects the
baby and absorbs crash forces. Adjust the child restraint
to the recline position (page 38). Place the child
restraint in your vehicle rear-facing. Adjust the restraint
so that the level arrow A is level with the ground.
2
Rear-facing
Rear-facing Installation with
Lower Anchor Connectors
Attach the harness straps B
to the splitter plate C using
the infant position (page 37)
on the harness straps.
As your child grows, you can
attach the harness straps B
to the splitter plate using the
pockets at the end of the
straps.
C
B
3
B
IMPORTANT: Make sure both harness straps are
installed completely on the splitter plate, as shown.
Pull the seat pad off of the front
of the child restraint. Route the
Lower Anchor Connector strap
D and hook through the
rear-facing belt paths E.
IMPORTANT: Make sure the
Lower Anchor Connector strap D
is in front of the crotch strap
F, and it lies flat without twisting,
as shown. Reconnect the seat pad
to the front of the child restraint.
E
F
D
18
19
Rear-facing Installation with
Lower Anchor Connectors
Rear-facing Installation with
Lower Anchor Connectors
WARNING
4
6
DO NOT use the two upper harness slots rear-facing. The
harness may not properly restrain the child during a crash.
Make sure the harness
straps are in one of the
three lower strap slots G.
The harness straps MUST
start at shoulder height
or lower, using the strap
slots closest to your child’s
shoulders H, as shown.
I
H
U.S. Customers Only: For a taller child, the fourth set
of harness slots I can be used.
Note: These slots MUST start at shoulder height or lower
and be the closest slots to your child's shoulders.
Know Your Lower Anchor
Connector Assembly
5
The lower anchor connector assembly that comes with
your child restraint will be one of the two types below.
SecureRight™
Quick Connector™
Adjuster
Strap
Clip
Hook
J
Strap
Adjuster
K
J
L
J
Refer to your vehicle owner’s manual to locate the lower
anchor bars J on your vehicle seat. Attach the right
hook K, or clip L, to the right anchor bar J and the
left hook, or clip, to the left anchor bar. DOUBLE CHECK
that the lower anchor connector hook is fully engaged by
pulling hard on the lower anchor connector strap.
20
E
Rear-facing
G
WARNING
DO NOT use this child restraint if it moves more than
25 mm (1 in.) side-to-side or front to back at the
rear-facing belt path. Serious injury or death may result
from poor installation. If you can not tightly secure the
child restraint, try again or move it to another location,
or install with the vehicle seat belt.
Using your full weight, push the child restraint firmly into
the vehicle seat while pulling up on the lower anchor
connector assembly strap to tighten.
The lower anchor connector assembly strap must be as
tight as possible.
If you can move the child restraint more than 25 mm
(1 inch) side to side or front to back at the rear-facing
belt path E, the lower anchor connector assembly strap is
not tight enough. You will need to try again, find another
location for your child restraint, or install with the vehicle
seat belt (page 22). To remove the lower anchor connector
assembly strap, go to page 44.
21
Rear-facing Installation with Seat Belt
Rear-facing Installation with Seat Belt
WARNING
1
NEVER turn a child restraint
forward-facing with a child who
weighs less than 10 kg (22 lbs).
Crash forces may cause serious
injury or death.
3
WARNING
DO NOT use the two upper harness slots rear-facing. The
harness may not properly restrain the child during a crash.
F
D
A
Make sure the harness
straps are in one of the
three lower strap slots D.
The harness straps MUST
start at shoulder height
or lower, using the strap
slots closest to your child’s
shoulders E, as shown.
E
REAR OF VEHICLE
ARROW MUST BE LEVEL WITH
GROUND WHEN USED REAR-FACING
REAR OF VEHICLE
Infants MUST always ride facing the rear of the
vehicle. The back of the child restraint supports and
protects the baby and absorbs crash forces.
Adjust the child restraint to the recline position (page
38). Place the child restraint in your vehicle rear-facing.
Adjust the restraint so that the level arrow A is level
with the ground.
2
Attach the harness
straps B to the splitter
plate C using the
infant position (page 37)
on the harness straps.
As your child grows, you
can attach the harness
straps B to the splitter
plate using the pockets
at the end of the straps.
C
B
B
IMPORTANT: Make sure both harness straps are
installed completely on the splitter plate, as shown.
22
Rear-facing
ARROW MUST BE LEVEL WITH
GROUND WHEN USED REAR-FACING
U.S. Customers Only: For a taller child, the fourth set
of harness slots F can be used. Note: These slots MUST
start at shoulder height or lower and be the closest slots
to your child's shoulders.
4
Lap Belt Only
Lap & Shoulder
Belt Combination
H
I
H
I
G
G
Pull the seat pad off of the front of the child restraint.
Route the vehicle seat belt G through the rear-facing
belt path H and continue through the opposite opening
of the child restraint. IMPORTANT: Make sure the seat
belt G is in front of the crotch strap I, and it lies flat
without twisting, as shown. Fasten the vehicle seat belt, as
shown, depending on your type of seat belt. Reconnect
the seat pad to the front of the child restraint.
23
Rear-facing Installation with Seat Belt
5
Locking Clip
installed properly
Install Locking Clip
(not included), if
necessary.
Rear-facing Installation with Seat Belt
6
G
If your vehicle was built prior
to model year 1996, and
has a lap/shoulder belt that is
equipped with an emergency
locking retractor (ELR) AND
13 mm
(0.5 inch)
sliding latch plate, you MUST
use a Locking Clip. Check
your vehicle owner’s manual
to identify which vehicle belt
system is in your vehicle.
If your vehicle is model year 1996 or newer, it likely
has a vehicle belt system that can be locked when
tightened, and will not require use of a Locking Clip.
Consult your vehicle owner’s manual before
installing a locking clip.
If your vehicle requires a Locking Clip, please call
ParentLink at 1-800-233-5921 (U.S.) or 1-937-773-3971
(Canada), or 01-800-706-12-00 (Mexico). to obtain a
Locking Clip and instructions on how to install and use it.
WARNING
Remove Locking Clip from vehicle seat belt when not used
with a child restraint, or the vehicle seat belt will not properly
restrain an adult or child. Serious injury could occur.
24
Rear-facing
H
WARNING
• If vehicle seat belts are not routed and fastened correctly,
the child restraint may not protect your child in a crash.
• Check your vehicle owner’s manual to determine how to
lock your seat belt for child restraint installation. The seat
belt must be locked to properly secure the child restraint.
• DO NOT use this child restraint if it moves more than
25 mm (1 in.) side to side or front to back at the rearfacing belt path. Serious injury or death may result from
poor installation. If you can not tightly secure the child
restraint, try again or move it to another location, or
install with the lower anchor connector assembly.
The seat belt must be as tight as possible.
Put your full weight onto the child restraint as you
tighten the seat belt G.
Check your work.
Make certain the belts are tight. If you can move the
child restraint more than 25 mm (1 inch) side to side or
front to back at the rear-facing belt path H, the vehicle
belt is not tight enough. If you have not tightly secured
the child restraint, try again, move it to another location, or
install with the lower anchor connector assembly (p. 18).
25
Using the Child Restraint
Forward-facing
Child Requirements:
Forward-facing Installation Checklist
1. Secure child restraint to the vehicle seat.
• Recline stand is flipped to the upright position
(page 38).
• Weight: 10 to 22.6 kg (22 to 50 lbs)
• Height: 71 to 127 cm (28 to 50 in.)
AND the tops of the child’s ears are at
or below, the top of the child restraint
seat back.
• Age: At least two years of age
• Install with Lower Anchor Connector Assembly
(page 28) or vehicle seat belt (page 32).
• Install tether strap (pages 31 and 35).
• Install locking clip, if necessary (page 33).
2. Set the child in the child restraint.
Tops of the child’s ears are at, or below, the top of
the child restraint seat back.
Harness straps are
at, or slightly above
the child’s shoulders.
3. Fasten the buckle. Refer to page 39.
4. Make necessary adjustments.
• Crotch strap is snug against the child (page 40).
• Harness straps MUST be snug against the child’s
shoulders, with no slack (page 39).
5. Position and connect chest clip.
Chest clip MUST be at armpit level (page 39).
6. Check your work.
• Recline Stand is flipped to the upright position
• To properly secure this child restraint it MUST NOT
•
Forward-facing
Belt Path
•
•
•
Lower Anchor
Connector
Assembly
Note: Once your child exceeds 22.6 kg (50 lbs) OR 127 cm
(50 inches) OR the top of their ears are above the top of the
child restraint seat back, they can no longer safely use this
child restraint, and you should consider using a booster seat.
26
move more than 25 mm (1 inch) from side to side
or front to back at the forward-facing belt path
(pages 30 and 34).
The child’s back and bottom are flat against the
back and bottom surfaces of the child restraint.
Shoulder harness straps MUST start at or above
shoulder height, using the strap slots closest to
your child’s shoulders (page 36).
Buckle tongues are fully engaged (page 39).
Tether strap is securely attached and tightened
(page 31 or 35).
Forward-facing
(page 38).
Lower Anchor
Connector
Assembly
WARNING
If your child weighs more than 22.6 kg (50 lbs) or their
shoulders are above the highest harness level, you
MUST discontinue use, or the child restraint will
not protect your child.
27
Forward-facing Installation with
Lower Anchor Connectors
1
WARNING
DO NOT use the three lower harness slots forward-facing.
The harness may not properly restrain the child in the event
of a crash.
A
WARNING
• ONLY use for securing child restraint to lower anchor bars.
• ALWAYS read and follow exactly the instructions which
accompany your vehicle and child restraint.
• NEVER attach two hooks to one vehicle lower anchor bar.
• DO NOT use the vehicle seat belts to install a child
restraint when using the Lower Anchor Connector
Assembly.
• This Lower Anchor Connector Assembly is intended to be
used ONLY as described in these instructions.
Serious injury or death may result from misuse.
• ALWAYS be sure that the Lower Anchor Connector hook is
fully engaged onto the Vehicle Lower Anchor Bar by pulling
hard on the Lower Anchor Connector strap. If it is not
totally engaged, the Lower Anchor Connector Assembly
will not secure your child restraint. Serious injury or death
may result.
• To avoid a strangulation hazard, you MUST store the
unused lower anchor connector assembly, with all slack
removed, in storage area on the bottom of the seat (page
45). Roll or fold excess lower anchor connector strap and
secure with a rubber band to prevent serious injury to
vehicle occupants.
• In addition to these instructions, read and follow your
vehicle owner’s manual regarding installation of child
restraints and LATCH. If there is a discrepancy, follow your
vehicle owner’s manual.
28
B
C
Make sure that the harness
straps are in one of the three
upper strap slots A. The
harness straps MUST start at
shoulder height or above, using
the strap slots closest to your
child’s shoulders C. The splitter
plate is attached to the bottom
of the harness strap in the child
position B (page 37). This will
provide more room for your
child to fit comfortably.
2
D
Forward-facing
LATCH is a system for attaching the child restraint to your
vehicle seat. It is to be used in place of your vehicle’s seat
belts and can be used in vehicles with LATCH anchors.
Your vehicle owner’s manual may refer to this system
as ISOFIX, Universal Anchorage System (UAS), or Lower
Universal Anchorage System.
Forward-facing Installation with
Lower Anchor Connectors
Adjust the child restraint to the upright position
(page 38) and place it in your vehicle forward-facing,
as shown. Route the Lower Anchor Connector Assembly
through each side of the forward-facing belt path D.
Note: Lift seat pad away from seat for easier access.
Make sure Lower Anchor Connector Assembly strap lies
flat without twisting.
29
Forward-facing Installation with
Lower Anchor Connectors
Know Your Lower Anchor
Connector Assembly
The lower anchor connector assembly that comes with
your child restraint will be one of the two types below.
SecureRight
Quick Connector
Adjuster
Strap
Clip
Hook
Strap
Adjuster
E
H
J
G
E
Refer to your vehicle owner’s manual to locate the lower
anchor bars E on your vehicle seat. Attach the right hook
F, or clip G, to the right anchor bar E and the left hook,
or clip, to the left anchor bar. DOUBLE CHECK that the
lower anchor connector hook is fully engaged by pulling
hard on the lower anchor connector strap.
4
Connect the tether hook
H to the vehicle tether
anchor I behind the
vehicle seat, as shown.
(Please consult your
vehicle owner’s manual,
as tether anchor locations
may vary.) Pull the strap
J and tighten the tether
securely.
WARNING
D
WARNING
DO NOT use this child restraint if it moves more than 25 mm (1 in.)
side-to-side or front to back at the forward-facing belt path. Serious
injury or death may result from poor installation. If you can not tightly
secure the child restraint, try again, move it to another location, or
install with the vehicle seat belt.
Using your full weight, push the child restraint firmly
into the vehicle seat, while pulling up on the lower anchor
connector strap to tighten.
The lower anchor connector strap must be as tight as
possible. If you can move the child restraint more than
25 mm (1 in.) side to side or front to back at the belt path
D, the lower anchor connector strap is not tight enough.
You will need to try again, find another location for your
child restraint, or install with the vehicle seat belt (page 32).
To remove the lower anchor connector strap, go to page 44.
30
WARNING
I
F
E
5
• Failure to follow these instructions could result in
serious injury to your child or other vehicle occupants.
• The tether strap is for forward-facing use only.
• To avoid a strangulation hazard, you MUST tightly roll
or fold excess tether strap and secure with the strap/
rubber band.
• Attach the tether hook to the storage clip when not
in use. This will keep an unused tether from hitting
someone during a crash.
After adjusting the top tether strap, you may have
excess strap; DO NOT cut it off. If you do, it may not be
long enough to use in another vehicle. Instead, tightly
roll up the excess tether strap and place the
rubber band around the bundle.
Note: Refer to your vehicle owner’s manual for the
location of the tether anchor bracket in your vehicle.
Older vehicles may not come equipped with anchor
bracket hardware. Check with your vehicle dealer.
If you have questions regarding tether anchors that are
not addressed by the vehicle owner’s manual or
answered by an authorized dealer/vehicle manufacturer,
call Evenflo’s ParentLink at 1-800-233-5921 (U.S.) or
1-937-773-3971 (Canada), or 01-800-706-12-00 (Mexico).
Forward-facing
3
31
Forward-facing Installation with Seat Belt
1
WARNING
Forward-facing Installation with Seat Belt
4
Lap Belt Only
Lap & Shoulder Belt
DO NOT use the three lower harness slots
forward-facing. The harness may not properly
restrain the child in the event of a crash.
B
2
3
D
32
Make sure that the harness
straps are in one of the three
upper strap slots A. The
harness straps MUST start at
shoulder height or above, using
the strap slots closest to your
child’s shoulders C. The splitter
plate is attached to the bottom
of the harness strap in the child
position B (page 37). This will
provide more room for your
child to fit comfortably.
Adjust the child restraint to
the upright position
(page 38). Place the child
restraint in your vehicle
forward-facing.
WARNING
If the vehicle belts are not
routed and fastened correctly,
the child restraint may not
protect your child in a crash.
Thread the vehicle seat
belt D through the
forward-facing belt path
behind the seat pad.
Note: Lift seat pad away
from seat for easier access.
Make sure vehicle seat belt
lies flat without twisting.
Fasten the vehicle seat belt as shown depending on
your type of seat belt.
Note: Install locking clip on lap and shoulder belt
combinations, if necessary.
5
Locking Clip
installed properly
Install Locking Clip
(not included), if
necessary.
If your vehicle was built prior
to model year 1996, and
has a lap/shoulder belt that is
equipped with an emergency
locking retractor (ELR) AND
13 mm
(0.5 inch)
sliding latch plate, you MUST
use a Locking Clip. Check
your vehicle owner’s manual
to identify which vehicle belt
system is in your vehicle.
If your vehicle is model year 1996 or newer, it likely
has a vehicle belt system that can be locked when
tightened, and will not require use of a Locking Clip.
Forward-facing
A
C
Consult your vehicle owner’s manual before
installing a locking clip.
If your vehicle requires a Locking Clip, please call
ParentLink at 1-800-233-5921 (U.S.) or 1-937-773-3971
(Canada), or 01-800-706-12-00 (Mexico) to obtain a
Locking Clip and instructions on how to install and use it.
WARNING
Remove Locking Clip from vehicle seat belt when not used
with a child restraint, or the vehicle seat belt will not properly
restrain an adult or child. Serious injury could occur.
33
Forward-facing Installation with Seat Belt
6
Forward-facing Installation with Seat Belt
7
WARNING
• Failure to follow these instructions could result in serious
injury to your child or other vehicle occupants.
• The tether strap is for forward-facing use only.
G
F
H
E
The vehicle seat belt must be as tight as possible.
Using your full weight, push the child restraint firmly
into the vehicle seat as you tighten the vehicle belt. If
you can move the child restraint more than 25 mm
(1 in.) side to side or front to back at the forward-facing
belt path E, the seat belt is not tight enough, you
will need to try again, or install with the lower anchor
connector assembly (page 28).
34
WARNING
• To avoid a strangulation hazard, you MUST tightly roll
or fold excess tether strap and secure with the strap/
rubber band.
• Attach the tether hook to the storage clip when not
in use. This will keep an unused tether from hitting
someone during a crash.
Forward-facing
WARNING
• If vehicle seat belts are not routed and fastened correctly,
the child restraint may not protect your child in a crash.
• Check your vehicle owner’s manual to determine how to
lock your seat belt for child restraint installation. The seat
belt must be locked to properly secure the child restraint.
• DO NOT use this child restraint if it moves more than
25 mm (1 in.) side to side or front to back at the
forward-facing belt path E. Serious injury or death may
result from poor installation. If you can not tightly secure
the child restraint, try again or move it to another
location, or install with the lower anchor connector
assembly (page 28).
Connect the tether
hook F to the vehicle
tether anchor G behind
the vehicle seat, as
shown. (Please consult
your vehicle owner’s
manual, as tether anchor
locations may vary.) Pull
the strap H and tighten
the tether securely.
After adjusting the top tether strap, you may have
excess strap; DO NOT cut it off. If you do, it may not be
long enough to use in another vehicle. Instead, tightly
roll up the excess tether strap and place the rubber
band around the bundle.
Note: Refer to your vehicle owner’s manual for the
location of the tether anchor bracket in your vehicle.
Older vehicles may not come equipped with anchor
bracket hardware. Check with your vehicle dealer.
If you have questions regarding tether anchors that are
not addressed by the vehicle owner’s manual or
answered by an authorized dealer/vehicle manufacturer,
call Evenflo’s ParentLink at 1-800-233-5921 (U.S.) or
1-937-773-3971 (Canada), or 01-800-706-12-00 (Mexico).
35
General Information
1
Positioning the Harness Strap
U.S. Customers
ONLY:
Rear-facing and
Forward-facing
This set of harness
slots can be for either
forward-facing or
rear-facing use.
Canadian
Customers:
This set of harness
slots can ONLY be
used forward-facing.
To change the
harness strap
position, loosen the
shoulder harness as
shown on page 41,
step 2. Slide the
harness strap off the
splitter plate D.
ONLY
C Forward-facing
Top Two Harness
Positions
D
B
2
Pull harness strap
through to the front of
the child restraint.
Thread each harness
strap through the
appropriate slot. Pull
the harness strap to
the back of the child
restraint.
A
U.S. and Canadian
Customers:
Rear-facing ONLY
Bottom Three
Harness Positions
Shoulder harness straps on this child restraint are
adjustable to six positions.
Canadian Customers: Rear-facing, the shoulder harness
straps MUST start at or below shoulder height using the
strap slots closest to your child’s shoulders in one of the
three lower harness positions A. The child’s head MUST
be at least 25 mm (1 inch) below the top of the seat back.
U.S. and Canadian Customers: Forward-facing, you
MUST use one of the top three harness positions B and
C. If the tops of the child’s ears are above the top of the
seat back, or the child’s shoulders fall above the upper
harness slots, you MUST discontinue use of this child
restraint. We recommend that you move your child to a
larger child restraint or a booster seat. You MUST use the
harness slots at or above the child’s shoulders AND closest
to your child’s shoulders.
36
3
Infant
Child
IMPORTANT: Make sure both harness straps are
installed completely on the splitter plate, as shown.
D
E
D
F
General
U.S. Customers Only: Rear-facing, the shoulder harness
straps MUST start at or below shoulder height using the
strap slots closest to your child’s shoulders in one of the
four lower harness positions A and B. The child’s head
MUST be at least 25 mm (1 inch) below the top of the
seat back.
Infant
Child
There are two positions on the harness straps. The top
loop E is for infant use. The bottom loop F is for use as
your child grows. Reattach the harness strap onto the
splitter plate D. Repeat on the other side.
37
4
Securing the Child in the Child Restraint
Make sure Harness Adjust Strap G is routed
over the Harness Strap H.
G
Place baby in the child restraint. The baby’s back and
bottom should be flat against the restraint. If there is a
gap, the baby will not be comfortable.
H
1
Lift the child restraint and flip
the recline stand A, located
under the child restraint
seat, to either the upright or
recline position.
A
Upright
Recline
Rear-facing Recline
The child restraint MUST be
in the RECLINE position for
rear-facing use. Child MUST
weigh 2.3 to 18 kg
(5 to 40 lbs).
ARROW MUST BE LEVEL WITH
GROUND WHEN USED REAR-FACING
B
REAR OF VEHICLE
C
A
Note: Recline position is
to be used for rear-facing
ONLY.
ARROW MUST BE LEVEL WITH
GROUND WHEN USED REAR-FACING
REAR OF VEHICLE
B
Bring each harness strap over
the child’s shoulders. Insert
the buckle tongues A into
the buckle.
Pull up on the harness strap
to check that the buckle
tongues are fastened.
Fasten the chest clip B
by snapping the two
halves together, as
shown.
Slide chest clip to armpit
level.
2
If the level arrow B is not
parallel to the ground, use a
tightly rolled towel or small
blanket C beneath the front
edge of the recline stand.
Forward-facing Upright
The child restraint MUST
be in the UPRIGHT position
for forward-facing use.
Child MUST weigh
10 to 22.6 kg (22 to 50 lbs)
and be at least two years of
age.
38
The harness straps must be snug against the child.
A snug strap should not allow any slack. It lies in a
relatively straight line without sagging. It does not press
on the child’s flesh or push the child’s body into an
unnatural position. Check the harness straps near the
shoulders for slack. You should NOT be able to pinch the
harness (see illustration). Adjust as needed.
General
Adjusting the Recline Stand
39
Adjusting the Crotch Strap
Adjusting the Harness Strap
1
This Child Restraint Has Two
Crotch Strap Positions
B
B
A
To reposition the crotch strap, first turn the child
restraint upside down. Turn the crotch strap harness
anchor A sideways and push it through the slot in the
bottom of the seat shell B.
Reposition the harness anchor into the other slot. Make
certain the harness anchor is properly seated against the
seat shell B.
Note: The crotch strap should be snug against the child.
Choose the slot that is closest to the child AND the most
comfortable for the child but NEVER under the child’s
bottom.
For Newborn Position
Place the anchor A through the rear slot, then feed it
through the front slot.
A
A
To tighten the harness straps, pull on the long harness
adjuster strap A on the front of the seat.
2
To loosen the harness
straps, push the
harness release
button B on the
front of the seat.
At the same time,
pull up on the
harness strap C near
the child’s shoulders.
C
A
B
Make sure the anchor is
completely through the front
slot and is lying flat against
the bottom of the seat.
General
A
IMPORTANT: Do not use this configuration for
infants weighing more than 4.5 kg (10 lbs).
40
41
Removing the Child from the Child
Restraint
A
3
WARNING
• To avoid a strangulation hazard, you MUST tightly roll or
fold excess tether strap and secure with the strap/rubber
band.
• Attach the tether hook to the storage clip when not in
use. This will keep an unused tether from hitting someone
during a crash.
E
C
B
Push the release button A and pull the chest clip apart.
Press the red buckle release B and remove the buckle
tongues C.
When the tether strap
is not in use, you
MUST attach the hook
E to the back of the
child restraint and
tightly roll and secure
the strap with the
strap/rubber band.
A loose tether strap
and hook may injure
your child.
Removing the Tether Strap
The tether strap that comes with your child
restraint will be one of the two types below.
A
B
Tilt the adjuster A and
slide the strap to loosen.
2
Press the tab C and
D twist, then remove
C
42
Press the adjuster release
button B to loosen.
General
1
the hook from the
anchor D.
43
Removing the Lower Anchor
Connectors
1
Removing the Lower Anchor
Connectors
TIP!
3
Using your full
weight, push the child
restraint into the vehicle
seat while loosening
the adjuster.
A
Or
When the Lower anchor
connector assembly is
not in use you MUST
attach the hooks C to
the bottom of the child
restraint. A loose Lower
Anchor Connector
assembly strap and hook
may injure your child.
B
C
Tilt the adjuster A and
slide the strap to loosen.
2
Press the adjuster release
button B to loosen.
The Lower Anchor Connector that comes with your
child restraint will be one of the two types below.
Installing the Accessories
D
C
44
D
E
To remove the hook C,
press the tab D and
twist, then remove from
anchor E.
Or
F
G
E
To remove the clip F,
pull the red release
strap G and remove clip
from anchor E.
General
The optional Head Pillow
D attaches easily and helps
support the child’s head.
Note: Attach Head Pillow
through harness slots just
above harness straps.
45
Securing Your Child Restraint in
Aircraft
The Federal Aviation Administration (FAA) recommends
that you secure your child for air travel in an appropriate
child restraint based on your child’s weight and size.
Turbulence can happen with little or no warning. When
turbulence occurs, the safest place for your child is
in a properly installed child restraint, not in an
adult’s lap or on the aircraft seat with its seat belt.
Keeping your child in a child restraint during the flight will
help ensure your family arrives safely at your destination.
Installing Child Restraint
Rear-facing in Aircraft
2
B
C
The FAA recommends that a child weighing:
• more than 18 kg (40 lbs) use an aircraft seat belt;
• less than 9 kg (20 lbs) use a rear-facing child restraint;
and
• from 9 to 18 kg (20 to 40 lbs) use a forward-facing
child restraint.
Please note that these FAA recommendations
may vary from those applicable to the use of
your child restraint in a motor vehicle.
IMPORTANT
You must use the internal harness when installing the child
restraint in aircraft.
Installing Child Restraint Rear-facing
in Aircraft
IMPORTANT: Before installing the child restraint, make sure
the aircraft seat is in a fully upright position.
A
Pull the seat pad off the front of the child restraint.
Route the aircraft seat belt A through the rear-facing
belt path B opening on one side and continue through
the belt path opening on the opposite side of the child
restraint, as shown above.
IMPORTANT: Make sure the aircraft seat belt A is in
front of the crotch strap C, as shown above.
3
A
ARROW MUST BE LEVEL WITH
GROUND WHEN USED REAR-FACING
REAR OF VEHICLE
Aircraft
Seat Belt
General
1
Fasten the aircraft seat belt A.
Adjust the child restraint to its recline position
(page 38), then place it on the aircraft seat rear-facing,
as shown above.
46
47
Installing Child Restraint
Rear-facing in Aircraft
4
Installing Child Restraint
Forward-facing in Aircraft
IMPORTANT: Before installing the child restraint, make sure
the aircraft seat is in a fully upright position.
1
D
B
A
Aircraft
Seat Belt
Check your work. Reconnect the seat pad to the front of
the child restraint. Try to move the child restraint in all
directions. If you can move the restraint more than
25 mm (1 inch) from side to side or front to back at the
rear-facing belt path B, the aircraft seat belt A is not
tight enough, and you MUST install again until the seat
belt is tight.
Adjust the child restraint to its upright position (page 38),
then place it on the aircraft seat forward-facing, as shown
above.
2
B
A
Route the aircraft seat belt A through the forward-facing
belt path opening in the back of the child restraint and
continue through the belt path opening B on the
opposite side of the child restraint.
Note: Lift the restraint’s seat pad away for easier access.
48
General
The aircraft seat belt A must be as tight as possible. Route
the excess seat belt strap D back through the rear-facing
belt path B opening, as shown above. Using your full
weight, push the child restraint firmly onto the aircraft
seat while pulling on the excess seat belt strap to tighten.
49
3
A
Fasten the aircraft seat belt A.
4
D
C
The aircraft seat belt must be as tight as possible. Route
the excess aircraft seat belt strap C back through the
forward-facing belt path D opening, as shown above.
Using your full weight, push the child restraint firmly onto
the aircraft seat while pulling on the excess seat belt strap
to tighten.
Note: Because of the fixed length of aircraft seat belts,
the belt buckle could be behind the child’s back after
tightening the belt. For your child’s comfort, Evenflo
recommends cushioning the child’s back by placing a
small pillow or folded-up blanket, or a folded-up jacket,
over the belt buckle.
Check your work. Reconnect the seat pad to the front
of the child restraint. Try to move the child restraint in all
directions. If you can move the restraint more than 25 mm
(1 inch) from side to side or front to back at the forwardfacing belt path, the aircraft seat belt is not tight enough,
and you MUST install again until the seat belt is tight.
50
Care and Cleaning
• DO NOT lubricate or immerse in water the LATCH
connectors, the buckle, or any other part of this child
restraint, unless rinsing is permitted, as stated on the back
of the buckle for your restraint.
• Plastic and metal parts may be wiped clean with mild
soap and water and dried with a soft cloth. Do not use
abrasive cleaners or solvents.
• Take care not to damage any labels.
• The harness can be wiped clean with mild soap and
water. Allow harness to air dry.
• Machine wash the seat pad separately in cold water,
delicate cycle. Tumble dry 10 to 15 minutes on low
heat.
• NEVER use child restraint without the seat pad.
• To protect the child restraint from damage caused by
weather, rodents, and other elements common to
garages, the outdoors, and other storage locations,
remove the seat pad and thoroughly clean the
restraint and pad prior to storage. Take care to clean
in the areas where crumbs and other debris tend to
accumulate.
TIP
IP!
To help protect the
vehicle upholstery, place a
towel beneath and behind
the child restraint.
General
Installing Child Restraint Forwardfacing in Aircraft
51
Replacement Parts
Limited Warranty
Not available on all models. Styles may vary.
To order replacement parts, you can order online at
www.evenflo.com or contact Evenflo. When you contact us,
please have the product model number and date of
manufacture (found on the back of the child restraint).
1
Locking Clip:
Not included
with child
restraint, see
page 24 or 33
5 Tether
9
Head Foam
6 Tether Extender:
2 Chest Clip
Not included with
child restraint
3 Crotch Strap 7
Lower Anchor
Connector
Assembly
Or
4 Harness
10 Head Pillow
11 Seat pad
Anchor
8 Lower
Connector
Assembly with
Quick Connectors
12 Recline Stand
For a period of 90 days from the original purchase of
this Product, Evenflo warrants to the original end user
(“Purchaser”) this Product (including any accessories)
against defects in material or workmanship. Evenflo’s
sole obligation under this express limited warranty shall
be, at Evenflo’s option, to repair or replace any Product
that is determined to be defective by Evenflo and
determined to be covered by this warranty.
Repair or replacement as provided under this warranty
is the exclusive remedy of the Purchaser. Proof of
purchase in the form of a receipted invoice or bill of
sale evidencing that the Product is within the warranty
period must be presented to obtain warranty service.
This express limited warranty is extended by Evenflo
ONLY to the original Purchaser of the Product and is not
assignable or transferable to subsequent purchasers or
end users of the Product. For warranty service, contact
Evenflo’s ParentLink Consumer Resource Center.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE
LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE ON
THIS PRODUCT IS HEREBY DISCLAIMED. EVENFLO
SHALL NOT BE LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL, SPECIAL OR PUNITIVE DAMAGES
OF ANY KIND FOR BREACH OF THE EXPRESS LIMITED
WARRANTY ON THIS PRODUCT, OR ANY WARRANTY
IMPLIED BY OPERATION OF LAW. OTHER THAN THE
EXPRESS LIMITED WARRANTY SET FORTH ABOVE, THERE
ARE NO OTHER WARRANTIES THAT ACCOMPANY THIS
PRODUCT AND ANY ORAL, WRITTEN OR ANY OTHER
EXPRESS REPRESENTATION OF ANY KIND IS HEREBY
DISCLAIMED.
52
General
Proper Disposal of This Child Restraint
At the end of this child restraint’s useful life, Evenflo
encourages you to dispose of it properly. Most of the
components in this child restraint are recyclable.
1. Remove all fabric and padding.
2. Remove all screws and disassemble the restraint.
3. Recycle all plastic/foam parts and discard the rest.
If your local recycling center won’t accept the padding,
you may dispose of it in the landfill.
NOTE: Evenflo uses recycled materials in the
manufacturing process whenever possible but never for
components that are critical for safety.
• www.evenflo.com
• USA: 1-800-233-5921 8 AM – 5 PM E.T.
• Canada: 1-937-773-3971
• México: 01-800-706-12-00
53
After thoroughly reading and following these instructions,
use the plastic lanyard A to store the instructions on
either side of the child restraint. You may also store the
instructions behind the seat pad.
So
Childnus™
Rest
rain
ne
t Sy
p for r’s M
stem
future an
ua
Ow
Kee
Rearfac
2.3
ing
(5 to to 18 kg
40
lbs)
48
(19 to 102 cm
to
For 40 in.)
wa
10 to rd-fac
ing
(22 22 .6
to 50 kg
to 127 lbs)
8 to
cm
50
in.)
)
use
.
l
A
cion
es
00- en Esp
233
-59 añol,
21.
NING
:
of serio
owne us injur
r’s man y
g this
child ual prior
restr
aint.
WARNING:
To reduce the risk of serious injury
or death, read this owner’s manual prior
to installing and using this child restraint.
71 to 127 cm
(28 to 50 in.)
Rear-facing*
2.3 to 18 kg
(5 to 40 lbs)
48 to 102 cm
(19 to 40 in.)
Forward-facing*
10 to 22.6 kg
(22 to 50 lbs)
SonusTM
Owner’s Manual
Child Restraint System
Keep for future use.
* See page 1 for complete requirements.
Para instrucciones en Español,
llamar al: 1-800-233-5921
OR
y, Inc.
y,
• www.evenflo.com
• USA: 1-800-233-5921 8 AM – 5 PM E.T.
• Canada: 1-937-773-3971
• México: 01-800-706-12-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising