User`s Manual LGA775 Pentium 4 Intel 865G Industrial Motherboard

User`s Manual LGA775 Pentium 4 Intel 865G Industrial Motherboard
User’s Manual
2801550
LGA775 Pentium 4 Intel 865G
Industrial Motherboard
Acknowledgments
Award is a registered trademark of Award Software International,
Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel and Pentium 4 are registered trademarks of Intel
Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond is a registered trademark of Winbond Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.
ii
2801550 User’s Manual
Table of Contents
Introduction .......................................................1
Product Description............................................................. 1
Checklist.............................................................................. 2
Specifications ...................................................................... 3
Board Dimensions ............................................................... 4
Installations .......................................................5
Installing the CPU ............................................................... 6
ATX Power Installation ...................................................... 6
Installing the Memory ......................................................... 7
Setting the Jumpers ............................................................. 8
Connectors on 2801550 ...................................................... 12
Watchdog Timer Configuration ........................................ 24
BIOS Setup .......................................................27
Drivers Installation ......................................51
Intel 865G Chipset Software Intallation Utility ................ 52
Intel 865G Chipset Graphics Driver.................................. 55
Realtek AC97 Codec Audio Driver Installation................ 57
Intel PRO LAN Drivers Installation.................................. 58
Appendix ...........................................................59
A. I/O Port Address Map................................................... 59
B. Interrupt Request Lines (IRQ) ...................................... 60
2801550 User’s Manual
iii
This page is intentionally left blank.
iv
2801550 User’s Manual
INTRODUCTION
Introduction
Product Description
The world's first Pentium 4 LGA775 industrial motherboard based on
the Intel® 865G chipset, 2801550, supports processor FSB of
533/800MHz for processor speeds of up to 3.8GHz. With two DDR
memory socket on board, the motherboard accommodates a maximum
memory capacity of 2GB. Integrated chipset-graphics features CRT
VGA support with up to 64MB shared memory, while Ethernet
functionality is provided by an Intel® 10/100Mb and an optional
Gigabit Ethernet.
Supporting the latest LGA775 processors, the 2801550 supports four
COM ports based on the Winbond I/O chipset on board. A total of six
USB 2.0 ports can be used, as well as two serial ATA ports for high
data transfers. Advanced storage comes in the form of a type 2 Compact
Flash socket.
Interface function is available with one 8X AGP slot, four PCI slots and
two ISA slots. This ATX-form-factor board has dimensions of 305mm
by 244mm. Other features include a watchdog timer and 4-in/4-out
digital I/O.
The board comes in three models, as of this writing – 2801550, 2801550F
and 2801550V. 2801550 has 10/100Mb Ethernet, while 2801550F has both
10/100Mb and Gigabit Ethernet. 2801550V uses the 865GV chipset, has
10/100Mb Ethernet, but without AGP slot.
2801550 User’s Manual
1
INTRODUCTION
Checklist
Your 2801550 package should include the items listed below.
The 2801550 Industrial motherboard
This User’s Manual
1 IDE Ribbon Cable
1 Bracket for 1 Serial Port
1 Bracket for 2 Serial Ports
1 SATA Cable
I/O Shield Plate
1 CD containing the following:
Chipset Drivers
Flash Memory Utility
2
2801550 User’s Manual
INTRODUCTION
Specifications
Form Factor
CPU Type
System Speed
CPU Operating
Frequency
Green /APM
CPU Socket
Chipset
BIOS
Cache
VGA
AGP port
st LAN
nd LAN
Audio
Memory type
LPC I/O
Secondary IO
RTC/CMOS
Battery
Keyboard Controller
EPP/ECP
IDE
CF connector
Serial ATA connector
Board Size
D-type connectors
Power Connector
Expansion Slots
PCI to ISA Bridge
USB
IrDA
Digital I/O
Watchdog Timer
System Voltages
ATX
LGA 775 (Intel® Pentium® 4 / Celeron D)
2.53GHz~3.8GHz
533MHz / 800MHz
APM1.2
LGA775
Intel® 865G / 865GV Chipset
GMCH: 82865G 932-pin FC-BGA
ICH5: 82801EB 460-pin MBGA
FWH
Award BIOS; Support ACPI function
256K/1MB/2MB Level 2 cache
82865G built-in, support CRT
AGP 8X interface
Intel 82551QM 10/100Mb Ethernet
Intel 82547GI (CSA port) 1 Gigabit LAN controller
ICH5 built-in audio controller + AC97 Codec
ALC655 (5.1 channel)
2 x DDR 2.5V DDR400/333/266 SDRAM DIMM
module (support dual channel), Max. - 2GB
Winbond 83627HF: IrDAx1 Parallel x1, COM1
(RS-232), COM2 (RS-232/ RS422/RS485), FDC
1.44MB, Hardware monitor (3 thermal inputs, 8
voltage monitor inputs, VID0-4 , 1 chassis open
detection , 3 Fan Header)
Fintek F81216 support COM3, COM4 (RS-232)
ICH5 built-in
Lithium Battery
Winbond 83627HF built-in
Yes
ICH5 built-in, IDE1, 2 (Ultra DMA 33/66/100)
1 port, type II (use IDE2 slave)
2 ports
12 x 9.5
PS/2 keyboard/mouse, VGA (CRT), COM1, Printer,
Audio, (USBx2 +RJ-45) x2
ATX 12V 24-pin
AGP slot, 4 PCI Slots, 2 ISA slots (2801550V has no
AGP slot)
Winbond 83628,83629
6 ports, USB 2.0 (D-sub x 4 + pin header x 2)
Pin header
4 in / 4 out
Yes (256 segments, 0,1,2 255. sec/min)
+5V, +12V, -12V, 5VSB, -5V, 3.3V
2801550 User’s Manual
3
INTRODUCTION
Board Dimensions
4
2801550 User’s Manual
INSTALLATIONS
Installations
This section provides information on how to use the jumpers and
connectors on the 2801550 in order to set up a workable system. The
topics covered are:
Installing the CPU........................................................................ 6
ATX Power Installation ............................................................... 6
Installing the Memory .................................................................. 7
Setting the Jumpers ...................................................................... 8
Connectors on 2801550 ............................................................... 12
Watchdog Timer Configuration ................................................. 24
2801550 User’s Manual
5
INSTALLATIONS
Installing the CPU
The 2801550 motherboard supports a LGA 775 processor socket for
Intel® Pentium® 4 processors.
The LGA 775 processor socket comes with a lever to secure the
processor. Refer to the pictures below, from left to right, on how to place
the processor into the CPU socket. Please note that the cover of the
LGA775 socket must always be installed during transport to avoid
damage to the socket.
ATX Power Installation
Power is provided to the 2801550 motherboard with the ATX1 standard
24-pin ATX power supply connector and J5 ATX 12V power connector.
These two power connectors should be utilized for the motherboard to
function.
6
2801550 User’s Manual
INSTALLATIONS
Installing the Memory
The 2801550 motherboard supports two DDR memory sockets for a
maximum total memory of 2GB in DDR memory type. The memory
module capacities supported are 64MB, 128MB, 256MB, 512MB and
1GB. The following table lists the supported DDR DIMM
configurations. Intel 865G supports configurations defined in the
JEDEC DDR DIMM specification only (A,B,C). Non-JEDEC standard
DIMMs such as double-sided x16 DDR SDRAM DIMMs are not
supported.
Supported DDR DIMM Configurations.
Density
Device
Width
Single/
Double
184-pin
DDR
64 Mbit
128Mbit
256Mbit
512Mbit
X8
X16
X8
X16
X8
X16
X8
X16
SS/DS
SS/DS
SS/DS
SS/DS
SS/DS
SS/DS
SS/DS
SS/DS
64/128MB
32MB/ NA 128/256MB 64MB/ NA 256/512MB 128MB/NA 512/1024M 256MB/NA
Installing and Removing Memory Modules
To install the DDR modules, locate the memory slot on the motherboard
and perform the following steps:
1. Hold the DDR module so that the key of the DDR module align with
those on the memory slot.
2. Gently push the DDR module in an upright position until the clips of
the slot close to hold the DDR module in place when the DDR module
touches the bottom of the slot.
3. To remove the DDR module, press the clips with both hands.
Lock
DDR Module
Lock
Lock
Lock
2801550 User’s Manual
7
INSTALLATIONS
Setting the Jumpers
Jumpers are used on 2801550 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on 2801550 and their respective functions.
Jumper Locations on 2801550.......................................................... 9
Configuring the CPU Frequency .................................................. 10
JP1, JP2, JP3: RS232/422/485 (COM2) Selection ....................... 10
JP4: Clear CMOS Contents .......................................................... 10
JP5: 10/100Mb LAN Enable/Disable ........................................... 10
8
2801550 User’s Manual
INSTALLATIONS
Jumper Locations on 2801550
Jumpers on 2801550 ...................................................................Page
JP1, JP2, JP3: RS232/422/485 (COM2) Selection ....................... 10
JP4: Clear CMOS Contents .......................................................... 10
JP5: 10/100Mb LAN Enable/Disable........................................... 10
2801550 User’s Manual
9
INSTALLATIONS
Configuring the CPU Frequency
The 2801550 motherboard does not provide DIP switches to configure
the processor speed (CPU frequency). The CPU frequency and processor
side bus of the processor can be automatically detected by the
motherboard.
JP1, JP2, JP3: RS232/422/485 (COM2) Selection
COM1 is fixed for RS-232 use only.
COM2 is selectable for RS232, RS-422 and RS-485. COM3 and COM4
are fixed for RS-232 use only. The following table describes the jumper
settings for COM2 selection.
COM2
Function
Jumper
Setting
(pin closed)
JP1:
1-2
JP1:
3-4
JP1:
5-6
JP2:
3-5 & 4-6
JP2:
1-3 & 2-4
JP2:
1-3 & 2-4
JP3:
3-5 & 4-6
JP3:
1-3 & 2-4
JP3:
1-3 & 2-4
JP4: Clear CMOS Contents
Use JP4, a 3-pin header, to clear the CMOS contents. Note that the
ATX-power connector should be disconnected from the motherboard
before clearing CMOS.
JP4
10
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
2801550 User’s Manual
INSTALLATIONS
JP5: 10/100Mb LAN Enable/Disable
If your motherboard comes with the Gigabit LAN functionality, you can
use this jumper to enable or disable it.
JP5
Setting
Function
Pin 1-2
Short/Closed
Enable
Pin 2-3
Short/Closed
Disable
2801550 User’s Manual
11
INSTALLATIONS
Connectors on 2801550
The connectors on 2801550 allows you to connect external devices such
as keyboard, floppy disk drives, hard disk drives, printers, etc. The
following table lists the connectors on 2801550 and their respective
functions.
Connector Locations on 2801550................................................... 13
ATX1: ATX Power Supply Connector......................................... 14
FDD1: Floppy Drive Connector ................................................... 14
IDE1, IDE2: EIDE Connectors..................................................... 15
FAN1: CPU Fan Power Connector............................................... 16
FAN2: Chassis Fan Power Connector .......................................... 16
FAN3: System Fan Power Connector........................................... 16
CN1: PS/2 Keyboard and PS/2 Mouse Connectors ...................... 16
CN2, J1, J10, J13: Serial Ports ..................................................... 17
CN3: Parallel Port Connector ....................................................... 18
CN4: VGA CRT Connector.......................................................... 18
CN5: USB and 10/100Mb LAN RJ45 Connectors ....................... 19
CN6: USB and Gigabit LAN RJ45 Connectors............................ 19
CN7: Line Out, Line In, Mic Connector....................................... 19
J2: Digital 4-in 4-out I/O Connector............................................. 20
J4: IrDA Connector ...................................................................... 20
J5: ATX 12V Power Connector.................................................... 20
J6: Compact Flash Connector ....................................................... 20
J7, J8: Serial ATA (SATA) Connectors ....................................... 20
J9: CD-In Audio Connector.......................................................... 21
J11: External Audio Connector .................................................... 21
J12: USB Connector ..................................................................... 21
J14: Wake on LAN Connector ..................................................... 21
J15: System Function Connector .................................................. 22
12
2801550 User’s Manual
INSTALLATIONS
Connector Locations on 2801550
Connectors on 2801550 ................................................................................................... Page
ATX1: ATX Power Supply Connector........................................................................................ 14
FDD1: Floppy Drive Connector .................................................................................................. 14
IDE1, IDE2: EIDE Connectors.................................................................................................... 15
FAN1: CPU Fan Power Connector.............................................................................................. 16
FAN2: Chassis Fan Power Connector ......................................................................................... 16
FAN3: System Fan Power Connector.......................................................................................... 16
CN1: PS/2 Keyboard and PS/2 Mouse Connectors..................................................................... 16
CN2, J1, J10, J13: Serial Ports .................................................................................................... 17
CN3: Parallel Port Connector ...................................................................................................... 18
CN4: VGA CRT Connector......................................................................................................... 18
CN5: USB and 10/100Mb LAN RJ45 Connectors ..................................................................... 19
CN6: USB and Gigabit LAN RJ45 Connectors .......................................................................... 19
CN7: Line Out, Line In, Mic Connector ..................................................................................... 19
J2: Digital 4-in 4-out I/O Connector ........................................................................................... 20
J4: IrDA Connector...................................................................................................................... 20
J5: ATX 12V Power Connector................................................................................................... 20
J6: Compact Flash Connector...................................................................................................... 20
J7, J8: Serial ATA (SATA) Connectors ...................................................................................... 20
J9: CD-In Audio Connector......................................................................................................... 21
J11: External Audio Connector ................................................................................................... 21
J12: USB Connector .................................................................................................................... 21
J14: Wake on LAN Connector .................................................................................................... 21
J15: System Function Connector................................................................................................. 22
2801550 User’s Manual
13
INSTALLATIONS
ATX1: ATX Power Supply Connector
Signal Name
3.3V
-12V
Ground
PS-ON
Ground
Ground
Ground
-5V
+5V
+5V
+5V
Ground
Pin #
13
14
15
16
17
18
19
20
21
22
23
24
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
Signal Name
3.3V
3.3V
Ground
+5V
Ground
+5V
Ground
Power good
5VSB
+12V
+12V
+3.3V
FDD1: Floppy Drive Connector
FDD1is a slim 26-pin connector and will support up to 1.44MB FDD.
Signal Name
VCC
VCC
VCC
NC
NC
NC
NC
GND
GND
GND
NC
GND
GND
14
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
2801550 User’s Manual
Signal Name
INDEX
DRV_SEL
DSK_CH
NC
MOTOR
DIR
STEP
WDATA
WGATE
TRACK
WPROT
RDATA
SIDE
INSTALLATIONS
IDE1, IDE2: EIDE Connectors
IDE1: Primary IDE Connector
Signal Name
IDE1
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
DRQ0
Host IOW
Host IOR
IOCHRDY
DACK0
IRQ14
Address 1
Address 0
Chip select 0
Activity
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Protect pin
Ground
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
IDE2: Secondary IDE Connector
IDE2
Signal Name
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
DRQ1
Host IOW
Host IOR
IOCHRDY
DACK1
IRQ15
Address 1
Address 0
Chip select 0
Activity
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
Signal Name
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Protect pin
Ground
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
[
2801550 User’s Manual
15
INSTALLATIONS
FAN1: CPU Fan Power Connector
1
2
3
4
Signal Name
Ground
+12V
Rotation detection
NC
FAN2: Chassis Fan Power Connector
FAN2 is a 3-pin header for the chassis fan. The fan must be a 12V fan.
1
2
3
Signal Name
Ground
+12V
Rotation detection
FAN3: System Fan Power Connector
FAN3 is a 3-pin header for a 12V fan.
1
2
3
Signal Name
Ground
+12V
Rotation detection
CN1: PS/2 Keyboard and PS/2 Mouse Connectors
PS/2 Mouse
PS/2 Keyboard
Below are the pin-out assignments of the connectors.
Signal Name
Keyboard data
N.C.
GND
5V
Keyboard clock
N.C.
16
Keyboard
1
2
3
4
5
6
Mouse
1
2
3
4
5
6
Signal Name
Mouse data
N.C.
GND
5V
Mouse clock
N.C.
2801550 User’s Manual
INSTALLATIONS
CN2, J1, J10, J13: Serial Ports
CN2 (COM1) is a DB-9 connector, while J1 (COM2), J10 (COM3) and
J13 (COM4) are pin headers.
COM1
Signal Name
DCD, Data carrier detect
RXD, Receive data
TXD, Transmit data
DTR, Data terminal ready
GND, ground
COM2/COM3/COM4
Pin #
1
2
3
4
5
Pin #
6
7
8
9
10
Signal Name
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
RI, Ring indicator
Not Used
J1 (COM2) is jumper selectable for RS-232, RS-422 and RS-485.
Pin #
RS-232
1
2
3
4
5
6
7
8
9
10
DCD
RX
TX
DTR
Ground
DSR
RTS
CTS
RI
NC
Signal Name
R2-422
RS-485
TXTX+
RX+
RXGround
RTSRTS+
CTS+
CTSNC
2801550 User’s Manual
DATADATA+
NC
NC
Ground
NC
NC
NC
NC
NC
17
INSTALLATIONS
CN3: Parallel Port Connector
CN3 is a DB-25 external. The following table describes the pin-out
assignments of this connector.
Signal Name
Line printer strobe
PD0, parallel data 0
PD1, parallel data 1
PD2, parallel data 2
PD3, parallel data 3
PD4, parallel data 4
PD5, parallel data 5
PD6, parallel data 6
PD7, parallel data 7
ACK, acknowledge
Busy
Paper empty
Select
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
Pin #
14
15
16
17
18
19
20
21
22
23
24
25
N/A
Signal Name
AutoFeed
Error
Initialize
Select
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
N/A
CN4: VGA CRT Connector
The pin assignments of the CN4 VGA CRT connector are as follows:
CN4
18
Red
Blue
GND
GND
N.C.
N.C.
HSYNC
NC
1
3
5
7
9
11
13
15
2
4
6
8
10
12
14
2801550 User’s Manual
Signal Name
Green
N.C.
GND
GND
GND
N.C.
VSYNC
INSTALLATIONS
CN5: USB and 10/100Mb LAN RJ45 Connectors
CN5 consists of an 10/100 RJ-45 connector (top) and two stacked USB
ports. Refer to the section below for their respective pin assignments.
USB0
USB1
Pin #
1
2
3
4
Signal Name
Vcc
USBUSB+
Ground
CN6: USB and Gigabit LAN RJ45 Connectors
CN6 consists of a Gigabit RJ-45 connector (top) and two stacked USB
ports. Refer to the section below for their respective pin assignments.
USB0
USB1
Pin #
1
2
3
4
Signal Name
Vcc
USBUSB+
Ground
CN7: Line Out, Line In, Mic Connector
The figure below shows the location of Line Out, Line In and Mic
connectors on CN7.
2801550 User’s Manual
19
INSTALLATIONS
J2: Digital 4-in 4-out I/O Connector
Ground
Out3
Out2
IN3
IN2
1
3
5
7
9
2
4
6
8
10
Signal Name
Vcc
Out1
Out0
IN1
IN0
J4: IrDA Connector
1
2
3
4
5
Signal Name
+5V
No connect
Ir RX
Ground
Ir TX
J5: ATX 12V Power Connector
Signal Name
Ground
Ground
+12V
+12V
1
2
3
4
J6: Compact Flash Connector
J7, J8: Serial ATA (SATA) Connectors
1
2
3
4
5
6
7
20
Signal Name
GND
TXP
TXN
GND
RXN
RXP
GND
2801550 User’s Manual
INSTALLATIONS
J9: CD-In Audio Connector
Pin #
1
2
3
4
Signal Name
CD Audio L
Ground
Ground
CD Audio R
J11: External Audio Connector
J11 is a 6-pin header that is used to connect to the optional audio cable
card that integrates jacks for Line Out and Mic.
LINEOUT_L
Ground
MIC 1
1
3
5
Signal Name
LINEOUT_R
Ground
MIC 2
2
4
6
J12: USB Connector
J12 connector will support the 3rd and 4th USB ports.
Vcc
USB2USB2+
Ground
J19
1
2
3
4
5
6
7
8
Signal Name
Ground
USB3+
USB3Vcc
J14: Wake on LAN Connector
J14 is a 3-pin header for the Wake on LAN function that will function
properly only with an ATX power supply with 5VSB that has 1A.
1
2
3
Pin #
1
2
3
Signal Name
+5VSB
Ground
Wake on LAN
2801550 User’s Manual
21
INSTALLATIONS
J15: System Function Connector
J15 provides connectors for system indicators that provide light
indication of the computer activities and switches to change the
computer status.
Hard Disk Drive LED
Reset Switch
Not Defined
ATX Power On Switch
SMI / Hardware Switch
Power LED
Speaker
Speaker: Pins 1 - 4
This connector provides an interface to a speaker for audio
tone generation. An 8-ohm speaker is recommended.
1
2
3
4
Signal Name
Speaker out
No connect
Ground
+5V
Power LED: Pins 11 - 15
The power LED indicates the status of the main power
switch.
11
12
13
14
15
22
2801550 User’s Manual
Signal Name
Power LED
No connect
Ground
No connect
Ground
INSTALLATIONS
SMI/Hardware Switch: Pins 6 and 16
This connector supports the "Green Switch" on the control
panel, which, when pressed, will force the system into the
power-saving mode immediately.
Signal Name
6
16
SMI
Ground
ATX Power ON Switch: Pins 7 and 17
This 2-pin connector is an “ATX Power Supply On/Off
Switch” on the system that connects to the power switch on
the case. When pressed, the power switch will force the
system to power on. When pressed again, it will force the
system to power off.
Reset Switch: Pins 9 and 19
The reset switch allows the user to reset the system without
turning the main power switch off and then on again.
Orientation is not required when making a connection to this
header.
Hard Disk Drive LED Connector: Pins 10 and 20
This connector connects to the hard drive activity LED on
control panel. This LED will flash when the HDD is being
accessed.
10
20
2801550 User’s Manual
Signal Name
HDD Active
5V
23
INSTALLATIONS
Watchdog Timer Configuration
The WDT is used to generate a variety of output signals after a user
programmable count. The WDT is suitable for use in the prevention of
system lock-up, such as when software becomes trapped in a deadlock.
Under these sort of circumstances, the timer will count to zero and the
selected outputs will be driven. Under normal circumstance, the user will
restart the WDT at regular intervals before the timer counts to zero.
SAMPLE CODE:
This code and information is provided "as is" without warranty of any
kind, either expressed or implied, including but not limited to the
implied warranties of merchantability and/or fitness for a particular
purpose.
;[]================================================
; Name : Enable_And_Set_Watchdog
; IN : AL - 1sec ~ 255sec
; OUT : None
;[]================================================
Enable_And_Set_Watchdog Proc Near
pushax
;save time interval
call Unlock_Chip
mov cl, 2Bh
call Read_Reg
and al, NOT 10h
call Write_Reg
;set GP24 as WDTO
mov cl, 07h
mov al, 08h
call Write_Reg
;switch to LD8
mov cl, 0F5h
call Read_Reg
and al, NOT 08h
call Write_Reg
pop ax
mov cl, 0F6h
call Write_Reg
24
;set count mode as second
;set watchdog timer
2801550 User’s Manual
INSTALLATIONS
mov al, 01h
mov cl, 30h
call Write_Reg
;watchdog enabled
call Lock_Chip
ret
Enable_And_Set_Watchdog Endp
;[]===============================================
; Name : Disable_Watchdog
; IN : None
; OUT : None
;[]===============================================
Disable_Watchdog Proc Near
call Unlock_Chip
mov cl, 07h
mov al, 08h
call Write_Reg
;switch to LD8
xor al, al
mov cl, 0F6h
call Write_Reg
;clear watchdog timer
xor al, al
mov cl, 30h
call Write_Reg
;watchdog disabled
call Lock_Chip
ret
Disable_Watchdog Endp
;[]===============================================
; Name : Unlock_Chip
; IN : None
; OUT : None
;[]===============================================
Unlock_Chip Proc Near
mov dx, 2Eh
mov al, 87h
out dx, al
out dx, al
ret
Unlock_Chip Endp
;[]================================================
; Name : Lock_Chip
; IN : None
; OUT : None
2801550 User’s Manual
25
INSTALLATIONS
;[]================================================
Unlock_Chip Proc Near
mov dx, 2Eh
mov al, 0AAh
out dx, al
ret
Unlock_Chip Endp
;[]================================================
; Name : Write_Reg
; IN : CL - register index
;
AL - Value to write
; OUT : None
;[]================================================
Write_Reg
Proc Near
push ax
mov dx, 2Eh
mov al,cl
out dx,al
pop ax
inc dx
out dx,al
ret
Write_Reg
Endp
;[]================================================
; Name : Read_Reg
; IN : CL - register index
; OUT : AL - Value to read
;[]================================================
Read_Reg
Proc Near
mov al, cl
mov dx, 2Eh
out dx, al
inc dx
in al, dx
ret
Read_Reg
Endp
;[]================================================
26
2801550 User’s Manual
BIOS SETUP
BIOS Setup
This chapter describes the different settings available in the Award
BIOS that comes with the motherboard. The topics covered in this
chapter are as follows:
BIOS Introduction ................................................................................ 28
BIOS Introduction ................................................................................ 29
BIOS Setup ............................................................................................ 29
Standard CMOS Setup......................................................................... 31
Advanced BIOS Features .................................................................... 34
Advanced Chipset Features................................................................. 38
Integrated Peripherals .......................................................................... 40
Power Management Setup................................................................... 43
PNP/PCI Configurations ..................................................................... 46
PC Health Status ................................................................................... 47
Frequency/Voltage Control ................................................................. 48
Load Fail-Safe Defaults ....................................................................... 49
Load Setup Defaults ............................................................................. 49
Set Supervisor/User Password............................................................ 49
Save & Exit Setup ................................................................................ 49
Exit Without Saving ............................................................................. 49
2801550 User’s Manual
27
BIOS SETUP
BIOS Introduction
This chapter describes the different settings available in the Award
BIOS that comes with the board. The topics covered in this chapter are
as follows:
BIOS Introduction ..................................................................... 29
BIOS Setup ................................................................................. 29
Standard CMOS Setup .............................................................. 31
Advanced BIOS Features.......................................................... 34
Advanced Chipset Features ...................................................... 38
Integrated Peripherals................................................................ 40
Power Management Setup ........................................................ 43
PNP/PCI Configurations ........................................................... 46
PC Health Status ........................................................................ 47
Frequency/Voltage Control ...................................................... 48
Load Fail-Safe Defaults ............................................................ 49
Load Setup Defaults .................................................................. 49
Set Supervisor/User Password ................................................. 49
Save & Exit Setup...................................................................... 49
Exit Without Saving .................................................................. 49
28
2801550 User’s Manual
BIOS SETUP
BIOS Introduction
The Award BIOS (Basic Input/Output System) installed in your
computer system’s ROM supports Intel® Pentium® 4 processors. The
BIOS provides critical low-level support for a standard device such as
disk drives, serial ports and parallel ports. It also adds virus and
password protection as well as special support for detailed fine-tuning of
the chipset controlling the entire system.
BIOS Setup
The Award BIOS provides a Setup utility program for specifying the
system configurations and settings. The BIOS ROM of the system stores
the Setup utility. When you turn on the computer, the Award BIOS is
immediately activated. Pressing the <Del> key immediately allows you
to enter the Setup utility. If you are a little bit late pressing the <Del>
key, POST (Power On Self Test) will continue with its test routines, thus
preventing you from invoking the Setup. If you still wish to enter Setup,
restart the system by pressing the ”Reset” button or simultaneously
pressing the <Ctrl>, <Alt> and <Delete> keys. You can also restart by
turning the system Off and back On again. The following message will
appear on the screen:
Press
<DEL>
to
Enter
Setup
In general, you press the arrow keys to highlight items, <Enter> to
select, the <PgUp> and <PgDn> keys to change entries, <F1> for help
and <Esc> to quit.
When you enter the Setup utility, the Main Menu screen will appear on
the screen. The Main Menu allows you to select from various setup
functions and exit choices.
2801550 User’s Manual
29
BIOS SETUP
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Advanced BIOS Features
Advanced Chipset Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
Frequency/Voltage Control
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
PC Health Status
Exit Without Saving
ESC : Quit
F10 : Save & Exit Setup
Ç È Æ Å : Select Item
Time, Date, Hard Disk Type
The section below the setup items of the Main Menu displays the control
keys for this menu. At the bottom of the Main Menu just below the
control keys section, there is another section, which displays information
on the currently highlighted item in the list.
Note:
If the system cannot boot after making and saving system
changes with Setup, the Award BIOS supports an override to
the CMOS settings that resets your system to its default.
Warning: It is strongly recommended that you avoid making any
changes to the chipset defaults. These defaults have been
carefully chosen by both Award and your system
manufacturer to provide the absolute maximum performance
and reliability. Changing the defaults could cause the system
to become unstable and crash in some cases.
30
2801550 User’s Manual
BIOS SETUP
Standard CMOS Setup
“Standard CMOS Setup” choice allows you to record some basic
hardware configurations in your computer system and set the system
clock and error handling. If the board is already installed in a working
system, you will not need to select this option. You will need to run the
Standard CMOS option, however, if you change your system hardware
configurations, the onboard battery fails, or the configuration stored in
the CMOS memory was lost or damaged.
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy)
Thu, May 21, 2001
Time (hh:mm:ss)
00 : 00 : 00
Item Help
Menu Level
IDE Primary Master
Press Enter 13020 MB
Change the day, month,
IDE Primary Slave
Press Enter None
Year and century
IDE Secondary Master
IDE Secondary Slave
Press Enter None
Press Enter None
Drive A
Drive B
1.44M, 3.5 in.
None
Video
Halt On
EGA/VGA
All Errors
Base Memory
Extended Memory
640K
129024K
Total Memory
130048K
At the bottom of the menu are the control keys for use on this menu. If
you need any help in each item field, you can press the <F1> key. It will
display the relevant information to help you. The memory display at the
lower right-hand side of the menu is read-only. It will adjust
automatically according to the memory changed. The following
describes each item of this menu.
Date
The date format is:
Day :
Month :
Date :
Year :
Sun to Sat
1 to 12
1 to 31
1999 to 2099
To set the date, highlight the “Date” field and use the PageUp/
PageDown or +/- keys to set the current time.
2801550 User’s Manual
31
BIOS SETUP
Time
The time format is:
Hour : 00 to 23
Minute : 00 to 59
Second : 00 to 59
To set the time, highlight the “Time” field and use the <PgUp>/ <PgDn>
or +/- keys to set the current time.
IDE Primary HDDs / IDE Secondary HDDs
The onboard PCI IDE connectors provide Primary and Secondary
channels for connecting up to four IDE hard disks or other IDE devices.
Each channel can support up to two hard disks; the first is the “Master”
and the second is the “Slave”.
Press <Enter> to configure the hard disk. The selections include Auto,
Manual, and None. Select ‘Manual’ to define the drive information
manually. You will be asked to enter the following items.
Capacity :
Cylinder :
Head :
Precomp :
Landing Zone :
Sector :
Capacity/size of the hard disk drive
Number of cylinders
Number of read/write heads
Write precompensation
Landing zone
Number of sectors
The Access Mode selections are as follows:
CHS
LBA (HD > 528MB and supports
Logical Block Addressing)
Large (for MS-DOS only)
Auto
Drive A / Drive B
These fields identify the types of floppy disk drive A or drive B that has
been installed in the computer. The available specifications are:
360KB 1.2MB 720KB 1.44MB 2.88MB
5.25 in. 5.25 in. 3.5 in.
3.5 in.
3.5 in.
32
2801550 User’s Manual
BIOS SETUP
Video
This field selects the type of video display card installed in your system.
You can choose the following video display cards:
EGA/VGA
For EGA, VGA, SEGA, SVGA
or PGA monitor adapters. (default)
CGA 40
Power up in 40 column mode. CGA
80
Power up in 80 column mode.
MONO
For Hercules or MDA adapters.
Halt On
This field determines whether or not the system will halt if an error is
detected during power up.
No errors
The system boot will not be halted for any error
that may be detected.
All errors
Whenever the BIOS detects a non-fatal error,
the system will stop and you will be prompted.
All, But Keyboard
The system boot will not be halted for a
keyboard error; it will stop for all other errors
All, But Diskette
The system boot will not be halted for a disk
error; it will stop for all other errors.
All, But Disk/Key
The system boot will not be halted for a keyboard or disk error; it will stop for all others.
2801550 User’s Manual
33
BIOS SETUP
Advanced BIOS Features
This section allows you to configure and improve your system and
allows you to set up some system features according to your preference.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features
Press Enter
Press Enter
Disabled
Enabled
Enabled
Enabled
Floppy
Hard Disk
CDROM
Enabled
Disabled
Disabled
On
Fast
Disabled
6
250
Setup
Enabled
1.4
Non-OS2
Yes
Enabled
CPU Feature
Hard Disk Boot Priority
Virus Warning
CPU L1 and L2 Cache
Hyper-Threading Technology
Quick Po wer On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up Numlock Status
Gate A20 Option
Typematic Rate Setting
Typematic Rate (chars/Sec)
Typematic Delay (Msec)
Security Option
APIC Mode
MPS Version Control for OS
OS Select For DRAM>64MB
Report No FDD For WIN 95
Small Logo (EPA) Show
ITEM HELP
Menu Level
Allows you choose
the VIRUS warning
feature for IDE Hard
Disk boot sector
protection. If this
function is enabled
and someone
attempt to write data
into this area, BIOS
will show a warning
message on screen
and alarm beep
Phoenix - AwardBIOS CMOS Setup Utility
CPU Features
16 Min
Thermal Monitor 1
Disabled
Delay Prior Thermal
Thermal Management
Limit CPUID MaxVal
ITEM HELP
Menu Level
Delay Prior to Thermal
This field activates the CPU thermal function after the systems boots for
the set number of minutes. The options are 16Min and 64Min.
Limit CPUID MaxVal
Enabled : Limit CPUID Maximum value to 3 when use older OS like
NT4. (Default value)
Disabled : Disables CPUID Limit for windows XP. (Default value)
34
2801550 User’s Manual
BIOS SETUP
Hard Disk Boot Priority
This item allows you to set the priority for hard disk boot. When you
press enter, the selections shows the current hard disks used in your
system as well as the Bootable Add-in Card that is relevant to other
boot sources media such as SCSI cards and LAN cards.
Virus Warning
This item protects the boot sector and partition table of your hard disk
against accidental modifications. If an attempt is made, the BIOS will
halt the system and display a warning message. If this occurs, you can
either allow the operation to continue or run an anti-virus program to
locate and remove the problem.
CPU L1 and L2 Cache
Cache memory is additional memory that is much faster than
conventional DRAM (system memory). CPUs from 486-type on up
contain internal cache memory, and most, but not all, modern PCs have
additional (external) cache memory. When the CPU requests data, the
system transfers the requested data from the main DRAM into cache
memory, for even faster access by the CPU. These items allow you to
enable (speed up memory access) or disable the cache function. By
default, these items are Enabled.
Hyper-Threading Technology
Hyper-Threading Technology enables two logical processors on a single
physical processor by replicating, partitioning, and sharing the resources
within the Intel NetBurst microarchitecture pipeline.
Quick Power On Self Test
When enabled, this field speeds up the Power On Self Test (POST) after
the system is turned on. If it is set to Enabled, BIOS will skip some
items.
First/Second/Third Boot Device
These fields determine the drive that the system searches first for an
operating system. The options available include Floppy, LS/ZIP,
HDD-0, SCSI, CDROM, HDD-1, HDD-2, HDD-3, LAN and Disable.
Boot Other Device
These fields allow the system to search for an operating system from
other devices other than the ones selected in the First/Second/Third Boot
Device.
2801550 User’s Manual
35
BIOS SETUP
Swap Floppy Drive
This item allows you to determine whether or not to enable Swap Floppy
Drive. When enabled, the BIOS swaps floppy drive assignments so that
Drive A becomes Drive B, and Drive B becomes Drive A. By default,
this field is set to Disabled.
Boot Up Floppy Seek
This feature controls whether the BIOS checks for a floppy drive while
booting up. If it cannot detect one (either due to improper configuration
or its absence), it will flash an error message.
Boot Up NumLock Status
This allows you to activate the NumLock function after you power up
the system.
Gate A20 Option
This field allows you to select how Gate A20 is worked. Gate A20 is a
device used to address memory above 1 MB.
Typematic Rate Setting
When disabled, continually holding down a key on your keyboard will
generate only one instance. When enabled, you can set the two typematic
controls listed next. By default, this field is set to Disabled.
Typematic Rate (Chars/Sec)
When the typematic rate is enabled, the system registers repeated
keystrokes speeds. Settings are from 6 to 30 characters per second.
Typematic Delay (Msec)
When the typematic rate is enabled, this item allows you to set the time
interval for displaying the first and second characters. By default, this
item is set to 250msec.
Security Option
This field allows you to limit access to the System and Setup. The default
value is Setup. When you select System, the system prompts for the User
Password every time you boot up. When you select Setup, the system
always boots up and prompts for the Supervisor Password only when the
Setup utility is called up.
APIC Mode
APIC stands for Advanced Programmable Interrupt Controller. The
default setting is Enabled.
36
2801550 User’s Manual
BIOS SETUP
MPS Version Control for OS
This option is specifies the MPS (Multiprocessor Specification) version
for your operating system. MPS version 1.4 added extended
configuration tables to improve support for multiple PCI bus
configurations and improve future expandability. The default setting is
1.4.
OS Select for DRAM > 64MB
This option allows the system to access greater than 64MB of DRAM
memory when used with OS/2 that depends on certain BIOS calls to
access memory. The default setting is Non-OS/2.
Report No FDD For WIN 95
If you are using Windows 95/98 without a floppy disk drive, select
Enabled to release IRQ6. This is required to pass Windows 95/98's SCT
test. You should also disable the Onboard FDC Controller in the
Integrated Peripherals screen when there's no floppy drive in the system.
If you set this feature to Disabled, the BIOS will not report the missing
floppy drive to Win95/98.
Small Logo (EPA) Show
The EPA logo appears at the right side of the monitor screen when the
system is boot up. The default setting is Enabled.
2801550 User’s Manual
37
BIOS SETUP
Advanced Chipset Features
This Setup menu controls the configuration of the chipset.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Timing Selectable
CAS Latency Time
Active to Precharge Delay
DRAM RAS# to CAS# Delay
DRAM RAS# Precharge
Memory Frequency For
System BIOS Cacheable
Video BIOS Cacheable
Memory Hole At 15M-16M
AGP Aperture Size (MB)
By SPD
2.5
7
3
3
Auto
Enabled
Enabled
Disabled
128
** On-Chip VGA Setting **
On-Chip VGA
On-Chip Frame Buffer Size
Boot Display
Enabled
8MB
CRT
ITEM HELP
Menu Level
DRAM Timing Selectable
This option refers to the method by which the DRAM timing is selected.
The default is By SPD.
CAS Latency Time
You can select CAS latency time in HCLKs of 2/2 or 3/3. The system
board designer should set the values in this field, depending on the
DRAM installed. Do not change the values in this field unless you
change specifications of the installed DRAM or the installed CPU. The
choices are 2 and 3.
Active to Precharge Delay
The default setting for the Active to Precharge Delay is 6.
DRAM RAS# to CAS# Delay
This option allows you to insert a delay between the RAS (Row Address
Strobe) and CAS (Column Address Strobe) signals. This delay occurs
when the SDRAM is written to, read from or refreshed. Reducing the
delay improves the performance of the SDRAM.
DRAM RAS# Precharge
This option sets the number of cycles required for the RAS to
accumulate its charge before the SDRAM refreshes. The default setting
for the Active to Precharge Delay is 3.
38
2801550 User’s Manual
BIOS SETUP
Memory Frequency For
This field sets the frequency of the DRAM memory installed. The
default setting is Auto. The other settings are DDR266,DDR320 and
DDR400.
System BIOS Cacheable
The setting of Enabled allows caching of the system BIOS ROM at
F000h-FFFFFh, resulting in better system performance. However, if
any program writes to this memory area, a system error may result.
Video BIOS Cacheable
The Setting Enabled allows caching of the video BIOS ROM at
C0000h-F7FFFh, resulting in better video performance. However, if
any program writes to this memory area, a system error may result.
Memory Hole At 15-16M
In order to improve performance, certain space in memory can be
reserved for ISA cards. This memory must be mapped into the memory
space below 16 MB. The choices are Enabled and Disabled.
AGP Aperture Size (MB)
The field sets aperture size of the graphics. The aperture is a portion of
the PCI memory address range dedicated for graphics memory address
space. Host cycles that hit the aperture range are forwarded to the AGP
without any translation. The default setting is 128M.
On-Chip VGA
The default setting is Enabled.
On-Chip Frame Buffer Size
The default setting is 8MB. The options available include 1MB, 8MB
and 16MB.
Boot Display
The default setting is CRT.
2801550 User’s Manual
39
BIOS SETUP
Integrated Peripherals
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals
On-Chip Primary IDE Device
Press Enter
Onboard Device
SuperIO Device
Press Enter
Press Enter
ITEM HELP
Menu Level
Phoenix - AwardBIOS CMOS Setup Utility
OnChip IDE Device
IDE Block Mode
On-Chip Primary PCI IDE
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
On-Chip Secondary PCI IDE
IDE Secondary Master PIO
IDE Secondary Slave PIO
IDE Secondary Master UDMA
IDE Secondary Slave UDMA
*** On-Chip Serial ATA Setting ***
SATA Mode
On-Chip Serial ATA
Serial ATA Port0 Mode
Serial ATA Port1 Mode
Enabled
Enabled
Auto
Auto
Auto
Auto
Enabled
Auto
Auto
Auto
Auto
ITEM HELP
Menu Level
IDE
Auto
SATA0 master
SATA1 master
Phoenix - AwardBIOS CMOS Setup Utility
Onboard Device
USB Controller
USB 2.0 Controller
USB Keyboard Support
USB Mouse Support
AC97 Audio
CSA LAN (Giga-LAN)
Init Display First
Enabled
Enabled
Disabled
Disabled
Auto
Enabled
PCI Slot
ITEM HELP
Menu Level
Phoenix - AwardBIOS CMOS Setup Utility
SuperIO Device
Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
RxD , TxD Active
IR Transmission Delay
UR2 Duplex Mode
Use IR Pins
Onboard Parallel Port
Parallel Port Mode
Mode Select
ECP Mode Use DMA
Onboard Serial Port 3
Serial Port 3 Use IRQ
Onboard Serial Port 4
Serial Port 4 Use IRQ
PWRON After PWR-Fail
40
Enabled
3F8/IRQ4
2F8/IRQ3
Normal
Hi, Lo
Enabled
Half
IR-Rx2T x2
378/IRQ7
SPP EPP
EPP1.7
3
3E8
IRQ11
ITEM HELP
Menu Level >
Disabled
IRQ10
Off
2801550 User’s Manual
BIOS SETUP
IDE HDD Block Mode
This field allows your hard disk controller to use the fast block mode to
transfer data to and from your hard disk drive.
OnChip Primary/Secondary PCI IDE
The integrated peripheral controller contains an IDE interface with
support for two IDE channels. Select Enabled to activate each channel
separately.
IDE Primary/Secondary Master/Slave PIO
These fields allow your system hard disk controller to work faster.
Rather than have the BIOS issue a series of commands that transfer to or
from the disk drive, PIO (Programmed Input/Output) allows the BIOS to
communicate with the controller and CPU directly.
The system supports five modes, numbered from 0 (default) to 4, which
primarily differ in timing. When Auto is selected, the BIOS will select
the best available mode.
IDE Primary/Secondary Master/Slave UDMA
These fields allow your system to improve disk I/O throughput to
33Mb/sec with the Ultra DMA/33 feature
On-Chip Serial ATA
The default setting of Auto allows the Serial ATA drive to be enabled,
when the system detects one.
USB Controller
The options for this field are Enabled and Disabled. By default, this field
is set to Enabled.
USB 2.0 Controller
The options for this field are Enabled and Disabled. By default, this field
is set to Disabled. In order to use USB 2.0, necessary OS drivers must be
installed first.
USB Keyboard Support
The options for this field are Enabled and Disabled. By default, this field
is set to Disabled.
USB Mouse Support
The options for this field are Enabled and Disabled. By default, this field
is set to Disabled.
2801550 User’s Manual
41
BIOS SETUP
AC97 Audio
The default setting of the AC97 Audio is Auto.
CSA LAN (Giga-LAN)
The field enables or disables this Intel Giga BaseT Ethernet controller.
Init Display First
By default, the system initializes the PCI Slot VGA when the system
boots.
Onboard FDC Controller
Select Enabled if your system has a floppy disk controller (FDC)
installed on the board and you wish to use it. If you install an add-in FDC
or the system has no floppy drive, select Disabled in this field. This
option allows you to select the onboard FDD port.
Onboard Serial/Parallel Port
These fields allow you to select the onboard serial and parallel ports and
their addresses. The default values for these ports are:
Serial Port 1
3F8/IRQ4
Serial Port 2
2F8/IRQ3
Serial Port 3
3E8/IRQ11
Serial Port 4
Disabled/IRQ10
Parallel Port
378H/IRQ7
UART Mode Select
This field determines the UART 2 mode in your computer. The default
value is Normal. Other options include IrDA and ASKIR.
Parallel Port Mode
This field allows you to determine parallel port mode function.
SPP
Standard Printer Port
EPP
Enhanced Parallel Port
ECP
Extended Capabilities Port
PWRON After PWR-Fail
This field sets the system power status whether on or off when power
returns to the system from a power failure situation.
42
2801550 User’s Manual
BIOS SETUP
Power Management Setup
The Power Management Setup allows you to save energy of your system
effectively.
Phoenix - AwardBIOS CMOS Setup Utility
Power Management Setup
ACPI Function
Power Management
Video Off Method
Video Off In Suspend
Suspend Type
Enabled
User Define
V/H SYNC+Blank
Yes
Stop Grant
Modem Use IRQ
3
Suspend Mode
HDD Po wer Down
Soft-Off by PWR-BTTN
CPU THRM-Throttling
Wake-Up by PCI Card
Power On by Ring
Wake Up On LAN
Resume by Alarm
Date (of Month) Alarm
Time (hh:mm:ss) Alarm
Disabled
Disabled
Instant-Off
50%
Disabled
Disabled
Disabled
Disabled
0
0:0 :0
** Reload Global Timer Events **
Primary IDE 0
Primary IDE 1
Secondary IDE 0
Secondary IDE 1
FDD, COM, LPT Port
PCI PIRQ[A-D] #
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
ITEM HELP
ACPI Function
Enable this function to support ACPI (Advance Configuration and
Power Interface).
Power Management
This field allows you to select the type of power saving management
modes. There are four selections for Power Management.
Min. Power Saving
Minimum power management
Max. Power Saving
Maximum power management.
User Define
Each of the ranges is from 1 min. to
1hr. Except for HDD Power Down
which ranges from 1 min. to 15 min.
Video Off Method
This field defines the Video Off features. There are three options.
V/H SYNC + Blank
Default setting, blank the screen and turn
off vertical and horizontal scanning.
DPMS
Allows BIOS to control the video display.
Blank Screen
Writes blanks to the video buffer.
2801550 User’s Manual
43
BIOS SETUP
Video Off In Suspend
When enabled, the video is off in suspend mode. The default setting is
Yes.
Suspend Type
The default setting for the Suspend Type field is Stop Grant.
Modem Use IRQ
This field sets the IRQ used by the Modem. By default, the setting is 3.
Suspend Mode
When enabled, and after the set time of system inactivity, all devices
except the CPU will be shut off.
HDD Power Down
When enabled, and after the set time of system inactivity, the hard disk
drive will be powered down while all other devices remain active.
Soft-Off by PWRBTN
This field defines the power-off mode when using an ATX power
supply. The Instant Off mode allows powering off immediately upon
pressing the power button. In the Delay 4 Sec mode, the system powers
off when the power button is pressed for more than four seconds or
enters the suspend mode when pressed for less than 4 seconds.
Wake-Up by PCI Cards
Enable this field to allow wake up function through a PCI card or
Onboard Intel 10/100 BaseT Ethernet.
Power On by Ring
This field enables or disables the power on of the system through the
modem connected to the serial port or LAN.
Wake Up On LAN
Enable this field to allow wake up function through Onboard Intel Giga
BaseT Ethernet.
Resume by Alarm
This field enables or disables the resumption of the system operation.
When enabled, the user is allowed to set the Date and Time.
44
2801550 User’s Manual
BIOS SETUP
Reload Global Timer Events
The HDD, FDD, COM, LPT Ports, and PCI PIRQ are I/O events which
can prevent the system from entering a power saving mode or can
awaken the system from such a mode. When an I/O device wants to gain
the attention of the operating system, it signals this by causing an IRQ to
occur. When the operating system is ready to respond to the request, it
interrupts itself and performs the service.
2801550 User’s Manual
45
BIOS SETUP
PNP/PCI Configurations
This option configures the PCI bus system. All PCI bus systems on the
system use INT#, thus all installed PCI cards must be set to this value.
Phoenix - AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
PNP OS Installed
No
Reset Configuration Data
Disabled
Resources Controlled By
IRQ Resources
DMA Resources
Auto (ESCD)
Press Enter
Press Enter
PCI/VGA Palette Snoop
INT Pin 1 Assignment
INT Pin 2 Assignment
INT Pin 3 Assignment
INT Pin 4 Assignment
INT Pin 5 Assignment
INT Pin 6 Assignment
INT Pin 7 Assignment
INT Pin 8 Assignment
Disabled
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
ITEM HELP
Menu Level
Default is Disabled.
Select Enabled to reset
Extended System
Configuration Data
(ESCD) when you exit
Setup if you have
installed a new add-on
and the system
reconfiguration has
caused such a serious
conflict that the OS
cannot boot
PNP OS Install
Enable the PNP OS Install option if it is supported by the operating
system installed. The default value is No.
Reset Configuration Data
This field allows you to determine whether to reset the configuration
data or not. The default value is Disabled.
Resources Controlled by
This PnP BIOS can configure all of the boot and compatible devices
automatically with the use of a use a PnP operating system such as
Windows 95.
PCI/VGA Palette Snoop
Some non-standard VGA display cards may not show colors properly.
This field allows you to set whether or not MPEG ISA/VESA VGA
cards can work with PCI/VGA. When this field is enabled, a PCI/VGA
can work with an MPEG ISA/VESA VGA card. When this field is
disabled, a PCI/VGA cannot work with an MPEG ISA/VESA card.
46
2801550 User’s Manual
BIOS SETUP
PC Health Status
This section shows the parameters in determining the PC Health Status.
These parameters include temperatures, fan speeds and voltages.
Phoenix - AwardBIOS CMOS Setup Utility
PC Health Status
Hardware Monitor
CPU Warning Temperature
System Temp.
CPU Te mp
CPU FAN Speed (FAN1)
System FAN Speed (FAN2)
System FAN Speed (FAN3)
Vcore(V)
Enabled
Disabled
28°C/82°F
42°C/107°F
5400
RPM
5463
RPM
5388
RPM
1.02 V
+3.3V
+5V
+12V
-12V
Shutdo wn Temperature
CPU Fan Failure Warning
Sys. Fan Failure Warning
Aux. Fan Failure Warning
3.32 V
4.94 V
12.03 V
-12.44 V
ITEM HELP
Menu Level >
Disabled
Disabled
Disabled
Disabled
Hardware Monitor
The Hardware Monitor can be enabled or disabled.
CPU Warning Temperature
This field allows the user to set the temperature so that when the
temperature is reached, the system sounds a warning. This function can
help prevent damage to the system that is caused by overheating.
Shutdown Temperature
This field allows the user to set the temperature by which the system
automatically shuts down once the threshold temperature is reached.
This function can help prevent damage to the system that is caused by
overheating.
Temperatures/Fan Speeds/Voltages
These fields are the parameters of the hardware monitoring function
feature of the board. The values are read-only values as monitored by the
system and show the PC health status.
CPU/Chassis Fan Failure Warning
When enabled, this field lets the system sounds a siren audible warning
to the user that the CPU fan or chassis fan has malfunctioned.
2801550 User’s Manual
47
BIOS SETUP
Frequency/Voltage Control
This section shows the user how to configure the processor frequency.
Phoenix - AwardBIOS CMOS Setup Utility
Frequency/Voltage Control
CPU Clock Ratio
Auto Detect PCI Clk
14X
Disabled
Spread Spectrum
Disabled
ITEM HELP
Menu Level
CPU Clock Ratio
The CPU Ratio, also known as the CPU bus speed multiplier, can be
configured through this field. The default setting is 14X. This parameter
can be used in conjunction with the above field to change the processor s
speed.
Auto Detect PCI Clk
This field enables or disables the auto detection of the PCI clock.
Spread Spectrum
This field sets the value of the spread spectrum. The default setting is
Disabled. This field is for CE testing use only.
48
2801550 User’s Manual
BIOS SETUP
Load Fail-Safe Defaults
This option allows you to load the troubleshooting default values
permanently stored in the BIOS ROM. These default settings are
non-optimal and disable all high-performance features.
Load Setup Defaults
This option allows you to load the default values to your system
configuration. These default settings are optimal and enable all high
performance features.
Set Supervisor/User Password
These two options set the system password. Supervisor Password sets a
password that will be used to protect the system and Setup utility. User
Password sets a password that will be used exclusively on the system. To
specify a password, highlight the type you want and press <Enter>. The
Enter Password: message prompts on the screen. Type the password, up
to eight characters in length, and press <Enter>. The system confirms
your password by asking you to type it again. After setting a password,
the screen automatically returns to the main screen.
To disable a password, just press the <Enter> key when you are
prompted to enter the password. A message will confirm the password to
be disabled. Once the password is disabled, the system will boot and you
can enter Setup freely.
Save & Exit Setup
This option allows you to determine whether or not to accept the
modifications. If you type “Y”, you will quit the setup utility and save all
changes into the CMOS memory. If you type “N”, you will return to
Setup utility.
Exit Without Saving
Select this option to exit the Setup utility without saving the changes you
have made in this session. Typing “Y” will quit the Setup utility without
saving the modifications. Typing “N” will return you to Setup utility.
2801550 User’s Manual
49
BIOS SETUP
This page is intentionally left blank.
50
2801550 User’s Manual
DRIVERS INSTALLATION
Drivers Installation
This section describes the installation procedures for software and
drivers under the Windows 98, Windows NT 4.0 and Windows 2000.
The software and drivers are included with the board. If you find the
items missing, please contact the vendor where you made the purchase.
The contents of this section include the following:
Intel 865G Chipset Software Intallation Utility ................ 52
Intel 865G Chipset Graphics Driver.................................. 55
Realtek AC97 Codec Audio Driver Installation................ 57
Intel PRO LAN Drivers Installation.................................. 58
IMPORTANT NOTE:
After installing your Windows operating system (Windows
98/98SE/ME/2000/XP), you must install first the Intel Chipset Software
Installation Utility before proceeding with the drivers installation.
2801550 User’s Manual
51
DRIVERS INSTALLATION
Intel 865G Chipset Software Intallation Utility
The Intel 865G Chipset Drivers should be installed first before the
software drivers to enable Plug & Play INF support for Intel chipset
components. Follow the instructions below to complete the installation
under Windows 98/98SE/ME/2000/XP.
1. Insert the CD that comes with the board and the screen below would
appear. Click Intel Chipsets and then Intel 865G Chipset Family
Drivers.
2. Click Intel 865G Chipset Software Intallation Utility.
52
2801550 User’s Manual
DRIVERS INSTALLATION
3. When the Welcome screen appears, click Next to continue.
4. Click Yes to accept the software license agreement and proceed with
the installation process.
2801550 User’s Manual
53
DRIVERS INSTALLATION
5. On Readme Information screen, click Next to continue the
installation.
6. The Setup process is now complete. Click Finish to restart the
computer and for changes to take effect. When the computer has
restarted, the system will be able to find some devices. Restart your
computer when prompted.
54
2801550 User’s Manual
DRIVERS INSTALLATION
Intel 865G Chipset Graphics Driver
The Intel 865G Chipset Family Graphics Drivers come in the CD with
the board . Follow the instructions below to complete the installation
under Windows 98/98SE/ME/2000/XP.
1. Insert the CD that comes with the board and the screen below would
appear. Click Intel Chipsets and then Intel 865G Chipset Family
Drivers.
2. When the Welcome screen appears, click Next to continue.
2801550 User’s Manual
55
DRIVERS INSTALLATION
3. Click Yes to accept the software license agreement and proceed with
the installation process.
4. The Setup process is now complete. Click Finish to restart the
computer and for changes to take effect. When the computer has
restarted, the system will be able to find some devices. Restart your
computer when prompted.
56
2801550 User’s Manual
DRIVERS INSTALLATION
Realtek AC97 Codec Audio Driver Installation
Follow the steps below to install the Realtek AC97 Codec Audio
Drivers.
1. Insert the CD that comes with the board and the screen below would
appear. Click Intel Chipsets, then Intel 865G Chipset Family Drivers.
Click Realtek AC97 Codec Audio Drivers to start installation.
2. Click Finish to restart the computer and for changes to take effect. .
2801550 User’s Manual
57
DRIVERS INSTALLATION
Intel PRO LAN Drivers Installation
The Intel PRO LAN drivers support both Intel® PRO/100 and
PRO/1000 drivers. Follow the steps below to complete the installation.
1. Insert the CD that comes with the board and the screen below would
appear. Click on LAN Card on the left side to make the LAN drivers
selection. Click on Intel(R) PRO LAN Drivers.
2. Click Install Now.
3. Click Restart to restart the computer and new settings to take effect.
58
2801550 User’s Manual
APPENDIX
Appendix
A. I/O Port Address Map
Each peripheral device in the system is assigned a set of I/O port
addresses which also becomes the identity of the device. The following
table lists the I/O port addresses used.
Address
000h - 01Fh
020h - 03Fh
040h - 05Fh
060h - 06Fh
070h - 07Fh
080h - 09Fh
0A0h - 0BFh
0C0h - 0DFh
0F0h
0F1h
1F0h - 1F7h
278h - 27Fh
2F8h - 2FFh
2B0h - 2DFh
378h - 3FFh
360h - 36Fh
3B0h - 3BFh
3C0h - 3CFh
3D0h - 3DFh
3F0h - 3F7h
3F8h - 3FFh
Device Description
DMA Controller #1
Interrupt Controller #1
Timer
Keyboard Controller
Real Time Clock, NMI
DMA Page Register
Interrupt Controller #2
DMA Controller #2
Clear Math Coprocessor Busy Signal
Reset Math Coprocessor
IDE Interface
Parallel Port #2(LPT2)
Serial Port #2(COM2)
Graphics adapter Controller
Parallel Port #1(LPT1)
Network Ports
Monochrome & Printer adapter
EGA adapter
CGA adapter
Floppy Disk Controller
Serial Port #1(COM1)
2801550 User’s Manual
59
APPENDIX
B. Interrupt Request Lines (IRQ)
Peripheral devices use interrupt request lines to notify CPU for the
service required. The following table shows the IRQ used by the devices
on board.
Level
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IRQ8
IRQ9
IRQ10
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
60
Function
System Timer Output
Keyboard
Interrupt Cascade
Serial Port #2
Serial Port #1
Reserved
Floppy Disk Controller
Parallel Port #1
Real Time Clock
Reserved
Reserved
Reserved
PS/2 Mouse
80287
Primary IDE
Secondary IDE
2801550 User’s Manual
Any advice or comments about our products and service,
or anything we can help you with please don t hesitate to
contact with us. We will do our best to support you for
your products, projects and business
Global American Inc.
Address
17 Hampshire Drive
Hudson, NH 03051
TEL
Toll Free (U.S. Only) 800-833-8999
(603)886-3900
FAX
(603)886-4545
Website
http://www.globalamericaninc.com
E-Mail
[email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement