advertisement
▼
Scroll to page 2
of 16
® < III 3583, 7636, 3247, 2970, 8531 SERIES _Product images may vary )RTANT SAFETY INSTRUCTIONS ! READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM. Always connect toapolarized outlet (one slotiswider thantheother). Unphg fromoutlet when notinuseandbefore conducting maintenance. When using anelectrical appliance, basic precautions should beobserved, including thefollowing: THE RISK OF FIRE, OR INJURY: ; connect to a polarized (one slot is wider than the ). Do not modify the polarplug to fit a non-polarized cord. not leave vacuum cleaner it is plugged in.Unplug when not in use nd before servicing. _o not use outdoors or on wet surfaces. Do not allow to be used as a toy. Close attention is necessarywhen used by or near children. >)Do not use for any purpose other than described in this User's Guide.Use only manufacturer's recommended attachments. >)Do not use with damaged cord or plug. If appliance is not working as it should,has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized servicecenter, Do not pull or carry by cord, use cord asa handle, closea door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keepcord away from heated surfaces. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. Hold plug when rewinding onto cord reel.Do not allow plug to whip when rewinding. Do not handle plug or vacuum cleaner with wet hands. Do not put any object into openings. Do not use with any opening blocked; keep openings free of dust, lint, hair,and anything that may reduce air flow. Keep hair,looseclothing, fingers, and all parts of body away from openings and moving parts. _)Turnoff all controls before plugging or unplugging vacuum cleaner. _)Use extra carewhen cleaning on stairs. _)Do not use to pick up flammable or combustible materials(lighter fluid, gasoline,kerosene,etc.) or use in areaswhere they may be present, _)Do not use vacuum cleaner in an enclosed space filled with vapors given off by oil base paint, paint thinner,some moth proofing substances,flammable dust, or other explosive or toxic vapors, >)Do not use to pick up toxic material (chlorine bleach, ammonia, drain cleaner,etc.). _)Do not pick up anything that is burning or smoking, such as cigarettes, matches,or hot ashes, _)Do not use without filters in place, _)Do not pick up hard or sharp objects such as glass, nails,screws, coins, etc. _)Useonly on dry, indoor surfaces, _)Keep appliance on a levelsurface, _)Do not carry the vacuumcleaner while it is running, _)Unplug before connecting or disconnecting the TurboBrush® Tool or TurboEraser®Pet Tool (on select models), SAVE THESE INSTRUCTIONS FOR FUTURE USE Thismodelisforhousehold useonly. THIS APPLIANCE HAS A POLARIZED PLUG Toreduce theriskofelectric shock, thisappliance hasapolarized plug(onebladeiswiderthantheother). Thisplugwillfitina polarized outletonlyoneway.Iftheplugdoesnotfitfullyintheoutlet,reverse theplug.Ifit stilldoesnotfit,contact aqualified electrician to install aproper outlet.Donotchange thepluginanywav. ....... _i_iiiii,!i_: ,,,,,'s,,' ....... A. Vacuum B. Handle C. Screws ,ii,i!!b Base F. Dusting G. Hose H. Crevice (2) D. Hose Wand Clip E. TurboBrush_R/TurboEraser Pet tool _Note: Crevice I. R J. (on select models) tool is located Brush Tool _ Extension Wand Pet Hair Corner Tool (on select models) inside Extension Wand Assembly 1, Slide handle onto machine 2, Screw 2 screws screwdriver into existing 3, Insert extension wand and twist clockwise base holes with Phillips-head clip into back of vacuum base 4, Line up tabs on the cuff of the hose with the notches on back of vacuum, twist hose clockwise to lock into place 5, Slide other end of hose into hose wand hose over upper hose wrap 6, Slide tools *Productimagesmayvary base and place into place www.BISSELL.com 8OO.257.7691 5 We're glad you purchased a BISSELL Safety Instructions ........... 2 Quick Start Guide ............ 3 Product View ................ 5 Your BISSELL vacuum is well made, and we back it with a limited Assembly ................... 6 three-year Operations ................ 7-9 vacuum. Everything we know about floor care went into the design and construction high-tech of this complete, home cleaning warranty. system. We also stand behind it with a knowledgeable, dedicated Consumer Care department, so, should Maintenance floor sweeper invented in t876. Today, BISSELL and service of high quality homecare products BISSELL vacuum. like your Thanks again, from all of us at BISSELL. Mark J. Bissett Chairman 4 & CEO www.BlSSELLcom _r Troubleshooting Replacement ............ Parts ......... 13 14 the is a global leader in the design, manufacture, 942 you ever have a problem, you'll receive fast, considerate assistance. My great-grandfather & Care ...... 800.237.7691 Warranty ................... 15 Service ..................... 15 Product Registration ........ 16 Consumer 16 Care ............. ] Handle 8 Bottom Easy Empty 2 Power switch** DirtTank 3 Tank Release Button 9 CordRewind 10 Post-Motor Filter 4 Carry Handle 5 Suction Powerlndicator** 11 Height Adjustment Knob 6 Lid Release Button 12 BrushRollOn/Off** 13 Furniture Protection Guard 7 Re-Motor Filter(located inside Dirt Tank lid) 14 Powerfoot TM 15 Cord Clip 22 Extension Wand Clip 16 TurboBrush_YTurboEraseP 25 Power Switch** PetTool** 24 Hose Wand 25 Hose WandBase 17 Upper Hose Wrap 26 Handle Release Pedal 18 Dusting Brush 19 Stretch Hose 27 FootHose 20 Crevice Tool(Grey) 21 Extension Wand AWARNING AWARNING AWARNING Plastic filmcanbedangerous, Toavoid danger ofsuffocation, keep away from babies andchildren. Donotpluginyourvacuum cleaner until youarefamiliar withallinstructions and operating procedures, Toreduce theriskofelectric shock, turn power switch offanddisconnect polarized plugfromelectrical outletbefore performing maintenance ortroubleshooting checks. *Product images mayvary **Onselect models www.BISSELL,_ AWARNING you'llneed__assemble your eaner isaPhillips-head screwdriver. handle Donot0peBtevacuum withdamp0rwetfilters orwithoutallfilteBinplacefiBt. to vacuum vacuum handle and remove the taped to the handle. The screw :ontains two screws of equal length. 2, the vacuum upright and slide the handle firmly into the opening at of the vacuum body _ck to be sure the handle is fitted to the Jm body. If there are any gaps between _andle and the vacuum base, continue to the handle firmly into the base until the idle is flush Insert the two screws from the screw packet the existing holes. Push each screw firmly _to the hole before beginning to secure the _crew with a Phillips head screwdriver. If the handle is aligned properly on the vacuum base, you should be able to push the screw almost entirely into the hole until only the screw head is visible. Tighten the screw with a Phillips head screwdriver by rotating the screw clockwise. Attach vacuum 4, hose_ clips & tools 1. Attach the extension wand clip by inserting the clip into the back of the vacuum base and twisting clockwise. Mount the extension wand (with crevice tool inside) on the back of the vacuum. 1. 2. Attach the Twist 'n Snap T" hose by lining up the tabs on the cuff with the corresponding notches on the back of the vacuum. Twist the Twist 'n Snap hose clockwise to lock the hose into place. 3. Slide the end of the hose wand into the hose wand base, and fold the hose over the upper hose wrap. NOTE: The powerfoot will not suction properly unless the hose wand is firmly attached. 2. 4. Slide the dusting brush into the opening below the upper hose wrap. 3. ACAUTION Power switch The Power switch on model 3583 is located on the left side of the vacuum. Push the rocker switch "ON" (I) to vacuum, and "OFF" (0) when cleaning is complete. The Power switch on models 7636, 3247, 2970, and 8531 is located on the front of the handle. Push the button (_ once to vacuum, and push the button (_ again when cleaning is complete. Before using v0urvacuum, make sure thatthedi_ tankisinthe10(ked position andthatbothfilters (prem0t0r andp0st-m0t0r) areinplace. Donot operate v0urvacuum without these filters. NOTE: You can find your model number on the back, bottom side of the vacuum on the white sticker by the UL rating. Handle position Press the handle release to place your CleanView three cleaning positions. 1. Upright - For storage cleaning with tools. 2. Normal cleaning for household floor pedal with your foot vacuum into one of and above floor - Press handle release cleaning tasks. 3. Low cleaning - With the vacuum in normal cleaning position, press handle release pedal again, use for reaching under low furniture such as tables, chairs or beds. Hei_lht adjustment There are five height settings available for various floor surfaces. Turn the dial on the foot of the cleaner to the desired setting. Lowest setting - For low pile carpet or bare floors. To pick up debris, it may be necessary to move up one setting. Medium setting Highest setting shag carpet. - For medium pile carpet. - For high pile and most NOTE: For optimal carpet cleaning performance, adjust to the lowest practical setting. If your cleaner is difficult to push, adjust to the next higher setting. If the dial is difficult to turn, tilt the cleaner back slightly to take the weight off the foot while turning. Transportin_l cleaner 1. To move your cleaner from room to room, put the handle in the upright position, tilt the cleaner back on its rear wheels and push forward. 2. The cleaner can also be moved carrying handle. *Product images mayvary by using the www.BISSELL.com 800,237.7691 7 Suction Power Indicator (On model series: 7636, 3247, 2970, 8531) The suction power indicator tells you when the air flow in your vacuum is reduced due to dirty filters or a clog in the hose. The suction power indicator will remain green until the airflow is reduced. At that time, it begins to change to red. When it is fully red, the airflow is significantly reduced by a dirty filter or clog. Follow the steps on page 12 for clearing a clog. Follow the steps on pages 9 and 10 to clean your filters. All filters in the vacuum should be cleaned or replaced when the clean filter indicator turns red. NOTE: When your vacuum is turned off, the suction power indicator will go to the green color setting. The suction power indicator only detects reductions in airflow when the vacuum power is on. Special tools Your BISSELL CleanView vacuum is not only a powerful carpet and rug vacuum cleaner, it's also a versatile above floor vacuum cleaner when you select one of the special tools. 1. Raise handle to upright NOTICE Pet Hair Lifter (model 8531) Justvacuum likeyounormally wouldandthepethair lifterwillgrabpethairwhenV0upullbackandsuction it upwhenyoupushforward. position. a. 2. Grasp the hose wand and separate hose wand base. 3. Attach tools by firmly pushing hose or extension wand. a. Crevice Tool Use in tight from c. the onto vacuum narrow spaces. b. Dusting Brush Use brush to dust furniture, blinds, books, lamps, shelves and baseboards. c. Extension Wand Use with desired attachment for a longer reach. d. TurboBrush®/TurboEraser® Pet Tool (models 7636 & 8531) Use rotating brush action for small flat areas such as stairs and cushions. Press gently down and pull toward you in a raking motion; too much pressure will cause the brush to stop rotating. e. Pet Hair Corner Tool (model 7636) Use tool in corners of room or stairs to pick up annoying dirt left stuck in the corners. Automatic Cord Rewind 1. Gently pull out power cord and stop when yellow is visible. Do not pull power cord beyond the red line. Plug cord into electrical outlet. 2. To return cord, turn vacuum power switch off, and remove plug from outlet. Hold plug and press automatic cord button to wind cord into reel. Do not allow plug to whip when rewinding. www.BISSELL.com _r 8OO.237.7691 d. e. AWARNING For models without a Brush Roll On/ Off switch (3583, 7636, 3247). Ther0tatin¢ floorbrush continues torotate while toolsareinuse. To reducethe riskofinjury frommoving pa_s, always move thecleaner withthecarrying handle attheback ofthe cleaner. Always place vacuum cleaner onfloorwithhandle inupright position whenusing tools. Never place y0ur fingers under thecleaner when itisrunning. Never place p0werfoot onfurniture oruneven surfaces. Donotplace vacuum cleaner close enough to0bje_st0 pulltheminto rotating brush. NOTICE Brush Roll On/Off The floorbrush willcontinue torotate whiley0uusey0ur vacuum forabove floorcleaning. Toprevent carpet damage, donotlean onthevacuum orletthep0werf00t tiltf0_ard. This effects models without abrush r0110n/0ff switch. (On Model Series: 2970 & 8531) The rotating brush On/Off pedal is located on the front of the vacuum base. You can use your foot to engage or disengage this pedal Ca). When the brush roll pedal has been engaged, the brush will start rotating. The brush roll should be turned on for most carpeted floors. To turn the brush roll off, disengage the pedal by pressing on it with your foot. We recommend turning off the brush roll for bare floor cleaning to prevent scatter or for other delicate surfaces. To maintain maximum following maintenance cleaning performance, the steps must be performed: 1. Empty the dirt tank when the dirt reaches "Full" line on the side. (See page 10) the 2. Check the pre-motor filter at least once a month and clean or replace as needed. To access the pre-motor filter, remove the Easy Empty dirt tank from the vacuum base and push the lid release button located on the carry handle. Remove the foam filter from the filter tray. On models 8531 and 7636 Series, a second small carbon filter is included here. Replace the second small, black odor-absorbing carbon filter as needed. a, AWARNING Toreduce theriskofelectric shock, turnpowerswitchoff anddisconnect polarized plugfromelectrical outletbefore performing maintenance ortroubleshooting checks, washable filter Lid Release Button NOTE: Black Carbon Filter is NOT washable. 3. The post-motor filter assists in the filtration process to return clean air to the room. Replace the post-motor filter every three to six months. To access the post-motor filter, remove the filter tray located below the Easy Empty dirt tank. When the filter becomes dirty, push the filter through the bottom of the tray to clean or replace the filter. fitter NOTE: The pleated post-motor filter may NOT be washed with water or detergent. If dust and/ or debris accumulates on the filter, gently tap the filter on the side of a garbage container. Note: More frequent filter cleaning or replacing may be necessary if you are vacuuming new carpet, fine dust, or have allergy concerns. Follow the instructions on the following pages to perform these simple maintenance steps. Post-Motor Filter Tray NOTICE While vacuuming, certain carpets andlowhumidity conditions maygenerate smallstatic discharges, The discharges areentirely harmless andarenotassociated inanywaywiththemainpowersupply. www.BISSELL._ Tank _nk needs to be emptied when the dirt "Full" line on the side of the tank. cleaner from electrical outlet. the Easy Empty dirt tank from the by pushing the tank release button. 'the dirt tank over a garbage container. bottom lid release button on the back dirt tank to empty dirt. Jnt the Easy Empty base. 2. 3. dirt tank back on the tank may be washed in warm with a mild detergent, Make sure it is ! before replacing, _1the pre-motor filter only genuine BISSELL replacement in your BISSELL CleanView vacuum. 1. Unplug 2. the cleaner from electrical and inner cyclone filters 2b. outlet. a. Remove the Easy Empty dirt tank and locate the pre-motor filter as described on the previous page. b. Remove the foam filter from the filter tray. In models 7636 and 8531 Series, a second carbon filter is included in here. The filter tray is fixed in-place, but may be removed for cleaning by unscrewing the tray. The foam filter and tray may be hand washed in warm water with a mild detergent, if desired. Rinse well, then air dry thoroughly before replacing the filter. Make sure all components are completely dry before replacing. A second black odorabsorbing filter can also be found here. Replace this when needed. 3, NOTE: Black Carbon Filter is NOT washable, 3. The inner cyclone may also be removed for cleaning. With the bottom of Easy Empty dirt tank open, reach up into the dirt cup and grasp the cyclone. Twist the cyclone clockwise to unlock and pull straight down to remove. Use the Lock and Unlock Icons on the tank to help guide the cyclone back in and lock it correctly. It B important to lock the cyclone back in correctly _sit will impact performance and separation. le inner cyclone and dirt cup may be wiped with a damp cloth. Make sure all parts are AWARNING Donotoperate cleaner withdamporwetfiltersor withoutallfiltersinplace. NOTICE Donotplace thedirttankorotherproduct components inthedishwasher. Handwashonly. Replacin_l the post-motor filter Use only a genuine BISSELL replacement post-motor filter in your BISSELL CleanView vacuum. 1. Unplug the cleaner from electrical 2. outlet. 2. The post-motor filter assists in the filtration process to return clean air to the room. Replace the post-motor filter every three to six months. To access the post-motor filter, remove the filter tray located below the Easy Empty dirt tank. When the filter becomes dirty, push the filter through the bottom of the tray to clean or replace the filter. Post-Motor Filter i NOTE: The pleated post-motor filter may NOT be washed with water or detergent. If dust and/ or debris accumulates on the filter, gently tap the filter on the side of a garbage container. Checkin_l rotatin_l floor brush and drive You should check your vacuum cleaner's rotating floor brush and drive belt regularly for wear or damage. You should also clean the brush and brush ends of strings, hair and carpet fibers. These can wrap around the brush and hamper its ability to effectively clean your carpet. Also remove any debris that has accumulated under the brush cover. 1. Unplug cleaner from electrical belt Brush Cover 3. outlet. 2. Place handle in low position and turn vacuum cleaner over so bottom side is up. 3. Remove the seven screws with a Phillips head screwdriver. Lift the brush cover off. 4. Grasp rotating floor brush at both ends and lift straight out of the vacuum foot. Slip off the belt. 4. Motor Pulle' 5. Clean strings, hair and other debris from rotating floor brush, paying particular attention to brush ends. 8. 6. Clean strings, hair and other debris from motor pulley and drive belt areas. Air Passageway 7. Check drive belt carefully for wear, cuts or stressed areas, and replace if necessary (see instructions on following page). 8. Check air passageway for obstructions. Remove debris from this area. www.BISSELL.com 800,237.7691 11 Replace drive belt Use only a genuine BISSELL style 9 replacement belt (#203-1093) in your BISSELL CleanView vacuum. 1. Unplug cleaner from electrical outlet. 2. With rotating floor brush removed from vacuum cleaner (steps 1-4 of Check rotating floor brush and drive belt), grasp old drive belt and remove from motor pulley. Discard old drive belt. AWARNING Toreduce theriskofelectric shock, turnpowerswitchoff anddisconnect polarized plugfromelectrical outletbefore performing maintenance 0rtr0ublesh00ting checks. 4. Motor Pulley 3. Place new drive belt over motor pulley and stretch other end over rotating floor brush in the space between the bristles. 4. Place ends of rotating floor brush down into slots on sides as shown. 5. Turn rotating floor brush by hand several times in the direction of motor pulley. If properly installed, drive belt will center itself on rotating brush. 6. Reposition the brush cover and screw all seven screws back into place. Clearin_l AWARNING Toreduce theriskofinjuryfrommovingparts, turn offvacuum cleaner anddisconnect PowerPlugfrom electrical outlet. a clo_l Low suction or poor pickup may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action of the dirt or brush roll, check for clogs. 1. Unplug cleaner from electrical outlet. 2. Remove Easy Empty dirt tank from base and empty dirt and debris. vacuum 3. Remove inner cyclone from Easy Empty dirt tank (see page 10) and check for debris build-up or clogs in the upper tank. 4. Check the suction inlet for a clog. 5. Grasp the hose wand to separate from the hose wand base. Check for a clog in the base, the wand or within the hose. 6. Remove the screw attaching the hose wand base to the vacuum. Straighten the hose wand base and check for clogs with a long, narrow object such as a broom stick. Do not use sharp objects like a clothes hanger, as these may puncture the hose. 7. If the clog persists, follow the instructions for Checking the rotating floor brush on page 11and inspect the air passageway for obstructions. 12 www, BISSELL,com _r 800,237,7691 6. Problem Possible Vacuum cleaner won't rum on Power causes Remedies cord not plugged Blown fuse/tripped Incorrect in Check electrical breaker Check/replace to suction Grasp the hose wand and firmly into the hose wand base Crack or hole in hose Check hose and replace Broken or worn drive belt Vacuum cleaner won't pick up dirt Rotating floor brush bristles Rotating floor brush jammed worn if Replace drive belt, see page 11 Replace brush Remove brush and clean debris brush ends, see page 11 Clog in vacuum Follow Dirt tank full clearing clogs Empty dirt tank Dirt tank or upper installed properly fuse or reset Adjust powerfoot to correct hei! height adjustment Hose not attached opening plug instructions on page 12 for tank not Position correctly and lock in place tank not Empty dirt tank . . Pos_t_on correctly and lock _n place Filters are dirty Tool won't pick up Dirt tank full . D_rt tank or upper installed properly Filters ./ are dirty Vacuum cleaner Incorrect Visible dirt escaping from cleaner Dirt tank full Cord will not retract Knotted height adjustment Filters missing incorrectly Please do not return this product to the store. Check and clean or replace pre-motor and post-motor filters see pages 9, 10 lust powerfoot height setting Empty or installed or twisted dirt tank Check pre-motor filters for correct Follow to correct instructions and post-motor installation on page 8 Other maintenance or service not included in the manual performed by an authorized service representative. Thank you for selecting a BISSELL product. For any questions or concerns, be of service. Contact us directl www.BISSELL._ These itemsareavailable foryourBISSELL CteanView Vacuums. Call 1-800-237-7691 PART # or visit www.bissell.com PART NAME PART NAME ]60-0159 BrushRoll(]3.5") (3583, 3247 Series) ]60-]503 BrushRoll (IS",7636 Series) ]604504 BrushRoll (]5",853]Series) 2034093 Style 9 DriveBelt (2-Pack) onepre-motor filterand onepost-motor filter) i......................................... ]604506 BrushRolldS") (2970 Series) 1217 PetFilter Pack (includes one washable foampro-motor filter, oneodor-absorbing carbon filter, andonepost-motor filter) (7636 &8531Serie9 ............................................. l ]215 Febmze ®Post-Motor Filter* (Fits allCleanView vacuum9 These items are available for your BISSELL CleanView Call 1-800-237-7691 or visit www.bissetLcom ]60q510 TurboEraser PetTool (7636 &853]Serie© 2034%7 Vacuums. Busting Brush 203-2666 Extension Wand (H",3583, 7636, 3247 Series) Extension Wand B",35835, 2970, 853] Series) 2034056 PetHairCorner Tool (7636 Series) CrevkeTool *Febreze _andrelated trademarks areowned byTheProcter &Gamble Companv, Cincinnati, Ohio, andusedunderlicense b ,BISSELL Homecare, Inc. 14 www.BISSELhcom _r 800.237.7691 This warranty gives youspecific legal_lts, andyoumayalso have otherrights whichmayvaryfromstatetostate.Ifyouneed additional instruction regarding thiswarranty orhavequestions regarding whatit maycover, please contact BISSELL Consumer Care byE-mail, telephone, orregular mailasdescribed below. Limited Three-Year Warranty Subject tothe*EXCEPTIONS AND EXCLUSIONS identified below, upon receipt oftheproduct BISSELL willrepair orreplace (withnewor remanufactured components orproducts), atBISSELL's option, free ofcharge fromthedateofpurchase bytheoriginal purchaser, for threeyears anydefective ormalfunctioning part. If your BISSELL product require service: VisitBISSELL.com BISSELL Authorized Service Center inyourarea, Ifyouneedinformation aboutrepairs orreplacement p have questions about yourwarranty, contact Website or E-mail: www.BISSELL.com Or Call: BISSELL Consumer Care 1-800-237-7691 See information on"IfyourBISSELL product should require service". Monday - Friday 8am - lOpm ET This warranty applies toproduct used forpersonal, andnotcommercial Saturday 9am - 8pm ET orrental service. This warranty does notapply tofans orroutine Sunday lOam - 7pm ET maintenance components such asfilters, belts, orbrushes, Damage or malfunction caused bynegligence, abuse, neglect, unauthorized repair, Or Write: oranyother usenotinaccordance withtheUser's Guide isnotcovered, BISSELL Homecare, Inc. PO Box 3606 BISSELL ISNOT LIABLE FOR INCIDENTAL ORCONSEQUENTIAL DAMAGES Rapids, HI 49501 OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT, BISSELL'SGrand ATTN: Consumer Care LIABILIIY WILL NOT EXCEED THE PURCHASE PRICE OFTHE PRODUCT. Somestatesdo not allowthe exclusionor limitation of incidentalor consequentialdamages,sothe abovelimitationor exclusionmay not apply to you. *EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY ISEXCLUSIVE ANDINLIEU OFANY OTHER WARRANTIES EITHER ORAL ORWRITTEN. ANYIMPLIED WARRANTIES WHICH MAY ARISE BYOPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY ANDFITNESS FOR APARTICULAR PURPOSE, ARE LIMITED TOTHE THREE YEAR DURATION FROM THE DATE OFPURCHASE ASDESCRIBED ABOVE. Some states donotallowlimitations on howlonganimplied warranty lastsotheabove limitation maynotapply toyou. NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim. www.BISSELL._ BISSELL Rewards Points Product Support Reminders and Alerts Automatically earn points for discounts and free shipping on future purchases. We'll contact you with any important product maintenance reminders and alerts. Faster Service Supplying saves you to contact regarding For information your information time should you us with questions your product. about repairs Special Promotions now need Optional: Register your email to receive notice of offers, contests, cleaning tips and more! or replacement Call: parts, or questions about your warranty: Write: BISSELL Consumer 1-800-237-7691 Care Monday 8 am - Friday Saturday Sunday Visit the When contacting BISSELL Homecare, PO Box 3606 - 10 pm am - 8 pm lOam - 7pm 9 BISSELL BISSELL, have record your Model Number: Please record your Purchase model Rapids IHI 49501 Consumer Care ET website: Please Grand ATTN: ET ET Inc, www.BISSELL.com number of cleaner available. Date: NOTE: Please keep your original sales receipt. It provides proof of purchase date in the event of a warranty claim, See Warranty on page 15 for details, 'c2013 BISSELL H0me(are. 1no Grand Rapids, Michigan Allrightsreserved. Printed inChina PartNumber160_587 Rev7/13 Visitourwebsite at:www'.%SEtL_0m 16
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project