TP600 and TP400 Control Panels
TP600 and TP400 Control Panels
User Interface and Programming Reference – Standard Menus
System Model:
BP-Series Systems are BP5XX, BP6XX, BP1XXX, BP2XXX.
Software Version:
7.0 and later
Panel Model:
TP600 Series
TP400 Series
Software Version:
2.3 or later
2.4 or later
JETS
TS
S
AUX
LIGHT
HEAT
HE
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
1
10-08-13
Main Menus
Navigation
Navigating the entire menu structure is done with 2 or 3 buttons on the control panel.
Some panels have separate WARM (Up) and COOL (Down) buttons, while
others have a single Temperature button. In the navigation diagrams
Temperature buttons are indicated by a single button icon.
Panels that have two Temperature buttons (Warm and Cool) can
use both of them to simplify navigation and programming where
a single Temperature icon is shown.
The LIGHT Button is also used to
choose the various menus and navigate each section.
Typical use of the Temperature button(s) allows changing the
Set Temperature while the numbers are flashing in the LCD.
Pressing the LIGHT button while the numbers are flashing will
enter the menus.
The menus can be exited with certain button presses. Simply waiting for
several seconds will return the panel operation to normal.
Key
Power-up Screens
Indicates Flashing or Changing Segment
Each time the System powers up, a series of numbers is displayed.
After the startup sequence of numbers, the system will enter Priming Mode (See Page 3).
Indicates Alternating or Progressive Message - every 1/2 second
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel configuration
Waiting time that keeps the last change to a menu item.
time (depends on menu item) that reverts to original setting and
***** Waiting
ignores any change to that menu item.
Main Screen
READY
RANGE FLTR1
SET
While the Temperature is
still flashing, press Light.
RANGE
Light Cycle if enabled
SET
RANGE
SET READY
SET
1
P
SET
Indicates a Menu Item that
Depends on a Manufacturer
Configuration and
may or may not appear.
If Time of Day is not set
“SET TIME” will
appear in this menu.
2
Main Screen
READY
RANGE FLTR1
Waiting Several Seconds in the Main Menu
will allow the display to revert to the Main Screen.
Most changes are not saved unless Light
is pressed.
Refer to Key above.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
2
10-08-13
Fill it up!
Preparation and Filling
Fill the spa to its correct operating level. Be sure to open all valves and jets in the plumbing system before filling to allow
as much air as possible to escape from the plumbing and the control system during the filling process.
After turning the power on at the main power panel, the top-side panel display will go through specific sequences. These
sequences are normal and display a variety of information regarding the configuration of the hot tub control.
Priming Mode – M019*
This mode will last for 4-5 minutes or you can manually exit the priming mode after the pump(s) have primed.
Regardless of whether the priming mode ends automatically or you manually exit the priming mode, the system will automatically return to normal heating and filtering at the end of the priming mode. During the priming mode, the heater is
disabled to allow the priming process to be completed without the possibility of energizing the heater under low-flow or
no-flow conditions. Nothing comes on automatically, but the pump(s) can be energized by pushing the “Jet” buttons.
If the spa has a Circ Pump, it can be activated by pressing the “Light” button during Priming Mode.
Priming the Pumps
As soon as the above display appears on the panel, push the “Jet” button once to start Pump 1 in low-speed and then
again to switch to high-speed. Also, push the Pump 2 or “Aux” button, if you have a 2nd pump, to turn it on. The pumps
will now be running in high-speed to facilitate priming. If the pumps have not primed after 2 minutes, and water is not
flowing from the jets in the spa, do not allow the pumps to continue to run. Turn off the pumps and repeat the process.
Note: Turning the power off and back on again will initiate a new pump priming session. Sometimes momentarily turning
the pump off and on will help it to prime. Do not do this more than 5 times. If the pump(s) will not prime, shut off the
power to the spa and call for service.
Important: A pump should not be allowed to run without priming for more than 2 minutes. Under NO circumstances should
a pump be allowed to run without priming beyond the end of the 4-5 minute priming mode. Doing so may cause damage to
the pump and cause the system to energize the heater and go into an overheat condition.
Exiting Priming Mode
You can manually exit Priming Mode by pressing a “Temp” button (Up or Down). Note that if you do not manually exit the
priming mode as described above, the priming mode will be automatically terminated after 4-5 minutes. Be sure that the
pump(s) have been primed by this time.
Once the system has exited Priming Mode, the top-side panel will momentarily display the set temperature but the display
will not show the temperature yet, as shown below. This is because the system requires approximately 1 minute of water
or
READY
RANGE
READY
RANGE
flowing through the heater to determine the water temperature and display it.
*M019 is a Message Code. See Page 15.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
3
10-08-13
Spa Behavior
Pumps
Press the “Jets 1” button once to turn pump 1 on or off, and to shift between low- and high-speeds if equipped.
If left running, the pump will turn off after a time-out period. The pump 1 low-speed will time out after 30 minutes. The
high-speed will time out after 15 minutes.
On non-circ systems, the low-speed of pump 1 runs when the blower or any other pump is on. If the spa is in Ready Mode
(See page 6), Pump 1 low may also activate for at least 1 minute every 30 minutes to detect the spa temperature (polling)
and then to heat to the set temperature if needed. When the low-speed turns on automatically, it cannot be deactivated
from the panel, however the high speed may be started.
Circulation Pump Modes
If the system is equipped with a circ pump, it will be configured to work in one of three different ways:
1, The circ pump operates continuously (24 hours) with the exception of turning off for 30 minutes at a time when the
water temperature reaches 3°F (1.5°C) above the set temperature (most likely to happen in very hot climates).
2, The circ pump stays on continuously, regardless of water temperature.
3, A programmable circ pump will come on when the system is checking temperature (polling), during filter cycles, during
freeze conditions, or when another pump is on.
The specific Circulation Mode that is used has been determined by the Manufacturer and cannot be changed in the field.
Filtration and Ozone
On non-circ systems, Pump 1 low and the ozone generator will run during filtration. On circ systems, the ozone will run with
the circ pump.
The system is factory-programmed with one filter cycle that will run in the evening (assuming the time-of-day is properly
set) when energy rates are often lower. The filter time and duration are programmable. (See page 10)
A second filter cycle can be enabled as needed.
At the start of each filter cycle, the blower (if there is one) or Pump 2 (if there is one) will run briefly to purge its plumbing to maintain good water quality.
Freeze Protection
If the temperature sensors within the heater detect a low enough temperature, then the pump(s) and the blower automatically activate to provide freeze protection. The pump(s) and blower will run either continuously or periodically depending
on conditions.
In colder climates, an optional additional freeze sensor may be added to protect against freeze conditions that may not
be sensed by the standard sensors. Auxiliary freeze sensor protection acts similarly except with the temperature thresholds
determined by the switch. See your dealer for details.
Clean-up Cycle (optional)
When a pump or blower is turned on by a button press, a clean-up cycle begins 30 minutes after the pump or blower is
turned off or times out. The pump and the ozone generator will run for 30 minutes or more, depending on the system. On
some systems, you can change this setting. (See the Preferences section on page 12)
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
4
10-08-13
Temperature and Temp Range
Adjusting the Set Temperature
When using a panel with Up and Down buttons (Temperature buttons), pressing Up or Down will cause the temperature to
flash. Pressing a temperature button again will adjust the set temperature in the direction indicated on the button. When
the LCD stops flashing, the spa will heat to the new set temperature when required.
If the panel has a single temperature button, pressing the button will cause the temperature to flash. Pressing the button
again will cause the temperature to change in one direction (e.g. UP). After allowing the display to stop flashing, pressing
the Temperature Button will cause the temperature to flash and the next press will change the temperature in the opposite
direction (e.g. DOWN).
Press-and-Hold
If a Temperature button is pressed and held when the temperature is flashing, the temperature will continue to change
until the button is released. If only one temperature button is available and the limit of the Temperature Range is reached
when the button is being held, the progression will reverse direction.
Dual Temperature Ranges
This system incorporates two temperature range settings with independent set temperatures. The High Range designated in
the display by an “up” arrow, and the Low Range designated in the display by a “down” arrow.
These ranges can be used for various reasons, with a common use being a “ready to use” setting vs. a “vacation” setting.
The Ranges are chosen using the menu structure below. Each range maintains its own set temperature as programmed by
the user. This way, when a range is chosen, the spa will heat to the set temperature associated with that range.
For example:
High Range might be set between 80°F and 104°F.
Key
Low Range might be set between 50°F and 99°F.
Indicates Flashing or Changing Segment
Indicates Alternating or Progressive Message - every 1/2 second
More specific Temp Ranges may be determined by the Manufacturer.
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel configuration
Freeze Protection is active in either range.
Waiting time that keeps the last change to a menu item.
See Ready and Rest on Page 6
for additional heating control information.
Main Screen
READY
Set Temp will Show & Flash
SET
RANGE FLTR1
High-Range vs.
Low-Range Temp Choice
RANGE
While
temperature
is flashing...
time (depends on menu item) that reverts to original setting and
***** Waiting
ignores any change to that menu item.
Press a Temp Button repeatedly to change the temperature.
SET
RANGE
SET
Main Screen
OR
Several Seconds
RANGE
READY
RANGE FLTR1
Pressing and holding a Temp Button will also change the temperature.
Toggle the Range arrows in the LCD.
Main Screen
To Set
RANGE
SET
SET
RANGE
READY
RANGE FLTR1
READY
RANGE FLTR1
Several Seconds
Reverts to Original Setting
To next item in Main Menu
Main Screen
*****
Waiting
Set Temp will Show & Flash
SET
RANGE FLTR1
Press a Temp Button repeatedly to change the temperature.
SET
RANGE FLTR1
SET
RANGE FLTR1
Main Screen
OR
Several Seconds
READY
RANGE FLTR1
Pressing and holding a Temp Button will also change the temperature.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
5
10-08-13
Mode – Ready and Rest
In order for the spa to heat, a pump needs to circulate water through the heater. The pump that performs this function is
known as the “heater pump.”
The heater pump can be either a 2-Speed Pump 1 or a circulation pump.
If the heater pump is a 2-Speed Pump 1, READY Mode will circulate water every 1/2 hour, using Pump 1 Low, in order to
maintain a constant water temperature, heat as needed, and refresh the temperature display. This is known as “polling.”
REST Mode will only allow heating during programmed filter cycles. Since polling does not occur, the temperature display
may not show a current temperature until the heater pump has been running for a minute or two.
Circulation Mode (See Page 4, under Pumps, for other circulation modes)
If the spa is configured for 24HR circulation, the heater pump generally runs continuously. Since the heater pump is always
running, the spa will maintain set temperature and heat as needed in Ready Mode, without polling.
In Rest Mode, the spa will only heat to set temperature during programmed filter times, even though the water is being
filtered constantly when in Circulation Mode.
Key
Main Screen
Indicates Flashing or Changing Segment
READY
RANGE
SET
RANGE FLTR1
While the Temperature is
still flashing, press Light
repeatedly until MODE
appears in the LCD.
Indicates Alternating or Progressive Message - every 1/2 second
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel configuration
Waiting time that keeps the last change to a menu item.
Main Screen
To Set
SET READY
SET
*****
Waiting
REST
Several Seconds
Reverts to Original Setting
REST RANGE FLTR1
Toggle between READY and REST
Pressing Light when the display is toggled will go to Main Screen.
To next item in
Main Menu
If not toggled
READY Mode will allow the spa to Poll and determine a need for heat. The panel will maintain a “current” temperature display.
REST Mode will not Poll and will only heat during filter cycles. The panel will not display a current temperature at all times.
Main Screen
REST RANGE FLTR1
time (depends on menu item) that reverts to original setting and
***** Waiting
ignores any change to that menu item.
1 Hour
REST RANGE
REST RANGE
REST RANGE
REST RANGE
REST RANGE
The Main Screen will display RUN PUMP FOR TEMP if the filtration pump has not run for over 1 hour.
The Main Screen will display normally during Filter Cycles or when the spa is in use.
If the filtration pump has been off for an hour or more, when any function button, EXCEPT Light, is pressed on the panel,
the pump used in conjuncton with the heater will run so that temperature can be sensed and displayed.
Ready-in-Rest Mode
READY/REST appears in the display if the spa is in Rest Mode and Jet 1 is pressed. It is assumed that the spa is being used
and will heat to set temperature. While Pump 1 High can be turned on and off, Pump 1 Low will run until set temperature
is reached, or 1 hour has passed. After 1 hour, the System will revert to Rest Mode. This mode can also be reset by entering
the Mode Menu and changing the Mode.
Main Screen
REST RANGE
Main Screen
J
READY/REST RANGE
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
6
10-08-13
Show and Set Time-of-Day
Be sure to set the Time-of-Day
Setting the time-of-day can be important for determining filtration times and other background features.
When in the TIME menu, SET TIME will flash on the display if no time-of-day is set in the memory.
24-hour time display can be set under the PREF menu. (See Page 10)
Key
Indicates Flashing or Changing Segment
Main Screen
READY
RANGE FLTR1
Indicates Alternating or Progressive Message - every 1/2 second
SET
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel configuration
While the Temperature is
still flashing, press Light
repeatedly until TIME
appears in the LCD.
RANGE
Waiting time that keeps the last change to a menu item.
time (depends on menu item) that reverts to original setting and
***** Waiting
ignores any change to that menu item.
Main Screen
Several Seconds
P
READY
RANGE FLTR1
To next item in
Main Menu
Main Screen
To Set
P
SET
SET
SET
P
P
SET
P
*****
Waiting
READY
RANGE FLTR1
Several Seconds
Reverts to Original Setting
If Time of Day is not actually programmed due to a power cycle,
SET TIME will appear in the menu instead of just TIME.
P
Note:
If power is interrupted to the system, Time-of-Day is not stored. The system will still operate and all other user settings
will be stored. If filter cycles are required to run at a particular time of day, resetting the clock will return the filter times
to the actual programmed periods.
When the system starts up, it defaults to 12:00 Noon, so another way to get filter times back to normal is to start up the
spa at noon on any given day. SET TIME will still flash in the TIME Menu until the time is actually set, but since the spa
started at noon, the filter cycles will run as programmed.
Flip (Invert Display)
Main Screen
READY
RANGE FLTR1
SET
While the Temperature is
still flashing, press Light
repeatedly until FLIP
appears in the LCD.
RANGE
Main Screen
or
Several Seconds
SET
SET
To next item in
Main Menu
If not toggled
READY
RANGE FLTR1
Toggle the inversion of the segmented characters
Pressing Light when the display is toggled will go to Main Screen.
Note:
Some panels may have a dedicated FLIP button,
which allows the user to flip the display with a single button-press.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
7
10-08-13
Restricting Operation
The control can be restricted to prevent unwanted use or temperature adjustments.
Locking the panel prevents the controller from being used, but all automatic functions are still active.
Locking the Temperature allows Jets and other features to be used, but the Set Temperature and other programmed settings
cannot be adjusted.
Temperature Lock allows access to a reduced selection of menu items.
These include Set Temperature, FLIP, LOCK, UTIL, INFO and FALT LOG.
Main Screen
READY
RANGE FLTR1
Key
RANGE
SET
Indicates Flashing or Changing Segment
While the Temperature is
still flashing, press Light
repeatedly until LOCK
appears in the LCD.
Locks Temp. and Settings.
Indicates Alternating or Progressive Message - every 1/2 second
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel configuration
Locks all function buttons.
Waiting time that keeps the last change to a menu item.
time (depends on menu item) that reverts to original setting and
***** Waiting
ignores any change to that menu item.
SET
SET
SET
Several Seconds
To next item in
Main Menu
Main Screen
To Set
SET
*****
Waiting
SET
Main Screen
Main Screen
Any
Button
Press
READY
RANGE FLTR1
READY
RANGE FLTR1
Several
Seconds
READY
RANGE FLTR1
RANGE FLTR1
LOCK will remain on the display
for 3 seconds and then revert to the normal display.
Temperature Locked
Main Screen
READY
READY
Several Seconds
Reverts to Original Setting
Panel Locked
Main Screen
RANGE FLTR1
RANGE
READY
RANGE FLTR1
Several
Seconds
READY
RANGE FLTR1
When the Temperature is locked, the panel will display the Set Temperature
by pressing a Temperature Button, as ususal.
LOCK will appear if an attempt to reset the temperature is made with a subsequent button press.
Adjustable settings in the menus are also locked.
Other function buttons will operate normally.
Unlocking
This Unlock sequence may be used from any screen that may be displayed on a restricted panel.
Main Screen
While pressing and holding the Temperature Button (or UP button, if available),
A Few
Seconds
Slowly press and release the Light Button two times.
READY
RANGE FLTR1
NOTE: If the panel has both an UP and a Down button, the ONLY button that will work in the Unlock Sequence is
the UP button.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
8
10-08-13
Hold (Standby)
Hold Mode – M037*
Hold Mode is used to disable the pumps during service functions like cleaning or replacing the filter. Hold Mode will last for
1 hour unless the mode is exited manually.
Drain Mode
Key
Some spas have a special feature that allows a pump to be
employed when draining the water.
When available, this feature is a component of Hold Mode.
Indicates Flashing or Changing Segment
Indicates Alternating or Progressive Message - every 1/2 second
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel configuration
Waiting time that keeps the last change to a menu item.
Main Screen
READY
RANGE FLTR1
SET
time (depends on menu item) that reverts to original setting and
***** Waiting
ignores any change to that menu item.
While the Temperature is
still flashing, press Light
repeatedly until HOLD
appears in the LCD.
RANGE
Main Screen
SET
Several Seconds
READY
Indicates a Menu Item that
Depends on a Manufacturer
Configuration and
may or may not appear.
RANGE FLTR1
To next item in
Main Menu
Some spas will allow
PUMP ING OUT (Drain Mode)
with Jet 1 button
OR
Press JET Button for Pump Out/Drain, only if Drain Mode is enabled.
J
Jet 1 will toggle pump on and off.
Main Screen
3 Seconds
READY
RANGE FLTR1
M037 is a Message Code. See Page 15.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
9
10-08-13
Adjusting Filtration
Main Filtration
Filter cycles are set using a start time and a duration. Start time is indicated by an “A” or “P” in the bottom right corner of
the display. Duration has no “A” or “P” indication. Each setting can be adjusted in 15-minute increments. The panel calculates the end time and displays it automatically.
Key
Indicates Flashing or Changing Segment
Indicates Alternating or Progressive Message - every 1/2 second
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel configuration
Main Screen
READY
RANGE FLTR1
SET
Waiting time that keeps the last change to a menu item.
While the Temperature is
still flashing, press Light
repeatedly until FLTR 1
appears in the LCD.
RANGE
time (depends on menu item) that reverts to original setting and
***** Waiting
ignores any change to that menu item.
Sets start hour
Shows/flashes start time
FLTR1
1
SET
FLTR1
P
Selects minutes
FLTR1
SET
Sets Filter 1 length in hours
to show RUN HRS
FLTR1
SET
P
Sets 15-minute increments
P
Selects part of an hour
FLTR1
SET
P
Waiting
Several Seconds
Reverts to Original Setting
*****
Sets 15-minute increments
Wait to
Revert
FLTR1
FLTR1
FLTR1
SET
FLTR1
SET
FLTR1
SET
to show F1 ENDS xx:xx
*****
Main Screen
To Set
A
To Set
FLTR 2
SET
FLTR 2
RANGE FLTR1
Main Screen
Waiting
Several Seconds
Reverts to Original Setting
SET
FLTR 2
Shows/flashes start time
To next item in
Main Menu
READY
will lose any new Filter 1
Start Time and Run Hours and
revert to the previous Filter 1 settings.
To Set
2
*****
Waiting several seconds
SET
FLTR 2 P
*****
READY
To Set
Sets start hour
SET
Selects minutes
FLTR 2 P
SET
Sets Filter 1 length in hours
to show RUN HRS
RANGE FLTR1
Sets 15-minute increments
FLTR 2 P
Selects part of an hour
FLTR 2 P
SET
Waiting
Several Seconds
Reverts to Original Setting
*****
Sets 15-minute increments
Wait to
Revert
FLTR 2
FLTR 2
SET
FLTR 2
SET
FLTR 2
FLTR 2
SET
to show F1 ENDS xx:xx
*****
Main Screen
To Set
A
*****
Waiting several seconds
READY
RANGE FLTR1
will lose any new Filter 2 On/OFF,
Start Time and Run Hours and
revert to any previous Filter 2 settings.
To Set
Filter Cycle 2 - Optional Filtration
Filter Cycle 2 is OFF by default.
It is possible to overlap Filter Cycle 1 and Filter Cycle 2, which will shorten
overall filtration by the overlap amount.
Purge Cycles
In order to maintain sanitary conditions, secondary Pumps and/or a Blower will
purge water from their respective plumbing by running briefly at the
beginning of each filter cycle.
If Filter Cycle 1 is set for 24 hours, enabling Filter Cycle 2 will initiate a purge
when Filter Cycle 2 is programmed to begin.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
10
10-08-13
Light Timer Programming
Light Timer Option
Key
Indicates Flashing or Changing Segment
If LITE TIMR does not appear in the Main Menu, the Light Timer
feature is not enabled by the manufacturer.
Indicates Alternating or Progressive Message - every 1/2 second
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel configuration
When available, the Light Timer is OFF by default.
Waiting time that keeps the last change to a menu item.
time (depends on menu item) that reverts to original setting and
***** Waiting
ignores any change to that menu item.
Main Screen
READY
RANGE FLTR1
SET
To next item in
Main Menu
While the Temperature is
still flashing, press Light
repeatedly until LITE TIMR
appears in the LCD.
RANGE
To Set
SET
Indicates a Menu Item that
Depends on a Manufacturer
Configuration and
may or may not appear.
Main Screen
Waiting
Several Seconds
Reverts to Original Setting
*****
SET
Shows/flashes start time
SET
to show RUN HRS
READY
To Set
A
Sets start hour
SET
RANGE FLTR1
Selects minutes
A
Sets Timer Length in hours
SET
Selects part of an hour
Sets 15-minute increments
A
SET
A
Waiting
Several Seconds
Reverts to Original Setting
*****
Sets 15-minute increments
Wait to
Revert
SET
SET
*****
SET
Main Screen
to show TIMR ENDS xx:xx
To Set
A
*****
Waiting several seconds
READY
RANGE FLTR1
will lose any new Lite Timer
On/OFF, Start Time and Run Hours and
revert to the previous Lite Timer settings.
To Set
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
11
10-08-13
Preferences
F / C (Temp Display)
Change the temperature between Fahrenheit and Celsius.
12 / 24 (Time Display)
Change the clock between 12 hr and 24 hr display.
RE-MIN-DERS (Reminders)
Turn the reminder messages (like “Clean Filter”) On or Off.
CLN-UP (Cleanup)
Cleanup Cycle Duration is not always enabled, so it may not appear. When it is available, set the length of time Pump 1 will
run after each use. 0-4 hours are available.
DOL-PHIN AD-DRES (Dolphin II and Dolphin III) Applies to RF Dolphin only.
(This message may not appear depending on the configuration)
When set to 0, no addressing is used. Use this setting for a Dolphin Remote which is factory set for no address by default.
When set between 1 and 7, the number is the address. (See the Dolphin manual for details.)
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
12
10-08-13
Preferences
Main Screen
READY
RANGE FLTR1
Key
SET
Indicates Flashing or Changing Segment
While the Temperature is
still flashing, press Light
repeatedly until PREF
appears in the LCD.
RANGE
Indicates Alternating or Progressive Message - every 1/2 second
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel configuration
Waiting time that keeps the last change to a menu item.
time (depends on menu item) that reverts to original setting and
***** Waiting
ignores any change to that menu item.
To show first item in Preferences menu
(F/C)
To next item in
Main Menu
(UTIL)
OR
Wait Several Seconds to
Return to Main Screen
Indicates a Menu Item that
Depends on a Manufacturer
Configuration and
may or may not appear.
Toggle °F and °C
*****
Wait to Revert
To Set
SET
Press Light
SET
Toggle 12-hour clock and 24-hour clock
for 12-24
*****
Wait to
To next item in
Main Menu
(UTIL)
Revert
SET
Press Light
To Set
SET
Toggle Yes and No
for REMINDERS
*****
Wait to
Revert
SET
Press Light
for CLEAN UP
SET
To view current setting and to toggle number of hours (0-4).
To Set
*****
Wait to
Revert
Only if Cleanup
Cycle is enabled.
SET
Press Light
SET
SET
To Set
to show Address Menu for Dolphin II or Dolphin III
RF Dolphin only.
OR
Several Seconds
To veiw current setting and to toggle address numbers for Dolphin II or Dolphin III (0-7)
*****
Wait to
Revert
SET
SET
SET
To Set
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
13
10-08-13
Utilities and Information
INFO (System Information sub-menu)
The System Information Menu displays various settings and identification of the particular system. As each item in the
menu is highlighted, the detail for that item is displayed at the bottom of the screen.
SSID (Software ID)
Displays the software ID number for the System.
MODL (System Model)
Displays the Model Number of the System.
SETP (Current Setup)
Displays the currently selected Configuration Setup Number.
SIG (Configuration Signature)
Displays the checksum for the system configuration file.
Heater Voltage (Feature not used on CE rated systems.)
Displays the operating voltage configured for the heater.
Heater Wattage as Configured in Software (CE Systems Only.)
Displays a heater kilowatt rating as programmed into the control system software (1-3 or 3-6).
H _ (Heater Type)
Displays a heater type ID number.
SW _ (Dip Switch Settings)
Displays a number that represents the DIP switch positions of S1 on the main circuit board.
PANL (Panel Version)
Displays a number of the software in the topside control panel.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
14
10-08-13
Additional Utilities
Utilities
In addition to INFO, The Utilities Menu contains the following:
GFCI (GFCI Test)
(Feature not available on CE rated systems.)
GFCI Test is not always enabled, so it may not appear. This screen allows the GFCI to be tested manually from the panel and
can be used to reset the automatic test feature. If the GFCI Test Feature is reset, the device will trip within 7 days. (See
Page 17)
A / B (A/B Sensor Temperatures)
When this is set to On, the temperature display will alternate to display temperature from Sensor A and Sensor B in the
heater.
FALT LOG (Fault Log)
The Fault Log is a record of the last 24 faults that can be
reviewed by a service tech.
DEMO (Demo Mode)
Demo Mode is not always enabled, so it may not appear. This is designed to operate several devices in a sequence in order
to demonstrate the various features of a particular hot tub.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
15
10-08-13
Utilities
Key
Indicates Flashing or Changing Segment
Indicates Alternating or Progressive Message - every 1/2 second
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel configuration
Main Screen
READY
RANGE FLTR1
SET
Waiting time that keeps the last change to a menu item.
While the Temperature is
still flashing, press Light
repeatedly until UTIL (Utilities)
appears in the LCD.
RANGE
time (depends on menu item) that reverts to original setting and
***** Waiting
ignores any change to that menu item.
Start display of string. There is a 2 second delay on each number.
Start display of string. There is a 2 second delay on each number.
To FIRST item in
Main Menu
(TEMP Range)
These strings will display once
and return to the beginning.
Press Temperature again to
display the string again.
Start display of string. There is a slight delay on each number.
120 or 240 VAC input power
sensed by a
OR
UL system at startup.
Waiting 10 seconds will allow
the screen to return to
normal operation.
3-6 or 1-3 Heater Wattage
as programmed. Displayed by a
CE system at startup.
Heater Type
DIP Switch 1 – Test Mode Off (0) or On (1)
DIP Switch 2+3+4 = the number of HS pumps with heat
DIP Switch
Settings
Store Settings (0) or Memory Reset (1)
N/A or Special Amperage Rule 1 or 2
Only if GFCI
is enabled
Displays GFCI Test Menu
See Page 17
To Set
SET
When set to ON, Panel will display
alternate readings from
Senor A and Sensor B
on Main Screen
*****
Waiting
SET
Several Seconds
Reverts to Original Setting
Displays Fault Log
Only if DEMO Mode
is enabled
Indicates a Menu Item that
Depends on a Manufacturer
Configuration and
may or may not appear.
See Page 18
SET
OR
Several Seconds
OR
Back to normal operation
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
16
10-08-13
Utilities – GFCI Test Feature
Not Available on CE Rated Systems.
A GFCI is an important safety device and is required equipment on a hot tub installation.
Your spa may be equipped with a GFCI Protection feature. (UL rated systems only.) If your spa has this feature enabled by
the manufacturer, the GFCI Trip Test must occur to allow proper spa function.
Within 1 to 7 days after startup, the spa will trip the GFCI to test it. (The number of days is factory programmed.) The GFCI
must be reset once it has tripped. After passing the GFCI Trip Test, any subsequent GFCI trips will indicate a ground fault or
other unsafe condition and the power to the spa must be shut off until a service person can correct the problem.
Key
Indicates Flashing or Changing Segment
Indicates Alternating or Progressive Message - every 1/2 second
Main Screen
READY
RANGE FLTR1
SET
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel configuration
While the Temperature is
still flashing, press Light
repeatedly until UTIL (Utilities)
appears in the LCD.
RANGE
Waiting time that keeps the last change to a menu item.
time (depends on menu item) that reverts to original setting and
***** Waiting
ignores any change to that menu item.
To FIRST item in
Main Menu
(TEMP Range)
Only if GFCI
is enabled
TRIP may also
appear briefly
under certain
circumstances.
One of these screens
will appear.
The GFCI will be tripped
at a random interval.
When the GFCI trips,
the spa will shut down.
After the breaker is
reset, PASS will
appear in this menu
and the spa will
operate normally.
Indicates a Menu Item that
Depends on a Manufacturer
Configuration and
may or may not appear.
If the GFCI does
NOT trip, FAIL will
appear and Spa
will not operate.
SET
*****
Or Wait to
Only appears
if a GFCI test
has been
passed.
To next item in
Info Menu
(A/B°)
Revert
*****
Or Wait to
*****
Or Wait to
Revert
Revert
*****
Waiting several seconds inside the GFCI Menu will allow the screen to return to normal operation.
Forcing the GFCI Trip Test
The installer can cause the GFCI Trip Test to occur sooner by initiating it using the above menu.
The GFCI should trip within several seconds and the spa should shut down. If it does not, shut down the power and manually verify that a GFCI breaker is installed and that the circuit and spa are wired correctly. Verify the function of the GFCI
with its own test button. Restore power to the spa and repeat the GFCI Trip Test.
Once the GFCI is tripped by the test, reset the GFCI and the spa will operate normally from that point. You can verify a successful test by navigating to the above menu. PASS should appear after a temp button is pressed from the GFCI screen.
The end-user must be trained to expect this one-time test to occur and how to properly reset the GFCI.
Warning:
If freezing conditions exist, a GFCI should be reset immediately or spa damage
could result. The end user should always trained to test and reset the
GFCI on a regular basis.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
17
10-08-13
Utilities – Fault Log
A Little History can tell a lot
The Fault Log stores up to 24 events in memory and they can be reviewed under the Fault Log Menu.
Each event captures a Fault Message Code, how many days have passed since the fault, Time of the fault, Set Temperature
during the fault, and Sensor A and B temperatures during the fault.
Main Screen
READY
RANGE FLTR1
SET
RANGE
Key
While the Temperature is
still flashing, press Light
repeatedly until UTIL (Utilities)
appears in the LCD.
Indicates Flashing or Changing Segment
Indicates Alternating or Progressive Message - every 1/2 second
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel configuration
Waiting time - varies depending on function
Press Light
repeatedly until FALT LOG
appears in the LCD.
To FIRST item in
Main Menu
(TEMP Range)
M: Message Code
READY
READY
RANGE
Indicates a Menu Item that
Depends on a Manufacturer
Configuration and
may or may not appear.
RANGE
D: Days Ago
SET
Only if DEMO Mode
is enabled
M:
READY
READY
RANGE
RANGE
Time
24 Fault messages is the maximum.
Fewer messages may be displayed.
READY
RANGE
P
Set Temperature
M:
READY
RANGE
Sensor A Temp
M:
The Fault Log is also available from the
Test Menu (in Test Mode).
READY
RANGE
Sensor B Temp
Waiting several seconds inside the Fault Log Menu will allow the screen to return to normal operation.
See following pages for various Message Codes and definitions.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
18
10-08-13
General Messages
Priming Mode – M019
Each time the spa is powered up, it will enter Priming Mode. The purpose of Priming Mode is to allow the user to run each
pump and manually verify that the pumps are primed (air is purged) and water is flowing. This typically requires observing
the output of each pump separately, and is generally not possible in normal operation. Priming Mode lasts 4 minutes, but
you can exit it earlier by pressing any Temp button. The heater is not allowed to run during Priming Mode.
NOTE: If your spa has a Circ Pump, it will turn on with Jets 1 in Priming Mode. The Circ Pump will run by itself when Priming Mode is exited.
or
READY
RANGE
READY
RANGE
Water Temperature is Unknown
After the pump has been running for 1 minute, the temperature will be displayed.
READY
RANGE FLTR1
Too Cold - Freeze Protection
A potential freeze condition has been detected, or the Aux Freeze Switch has closed, and all pumps and blower are activated. All pumps and blower are ON for at least 4 minutes after the potential freeze condition has ended, or when the aux
freeze switch opens.
In some cases, pumps may turn on and off and the heater may operate during Freeze Protection.
This is an operational message, not an error indication.
Water is too Hot (OHS) – M029
One of the water temp sensors has detected spa water temp 110°F (43.3°C) and spa functions are disabled. System will
auto reset when the spa water temp is below 108°F (42.2°C). Check for extended pump operation or
high ambient temp.
Safety Trip - Pump Suction Blockage* – M033
The Safety Trip error message indicates that the vacuum switch has closed. This occurs when there has been a suction problem or a possible entrapment situation avoided. (Note: not all spas have this feature.)
M0XX numbers are Message Codes. See Page 15.
* This message can be reset from the topside panel with any button press.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
19
10-08-13
Heater-Related Messages
Heater Flow is Reduced (HFL) – M016
There may not be enough water flow through the heater to carry the heat away from the heating element. Heater start up
will begin again after about 1 min. See “Flow Related Checks” below.
Heater Flow is Reduced (LF)* – M017
There is not enough water flow through the heater to carry the heat away from the heating element and the heater has
been disabled. See “Flow Related Checks” below. After the problem has been resolved, you must press any button to reset
and begin heater start up.
Heater may be Dry (dr)* – M028
Possible dry heater, or not enough water in the heater to start it. The spa is shut down for 15 min. Press any button to
reset the heater start-up. See “Flow Related Checks” below.
Heater is Dry* – M027
There is not enough water in the heater to start it. The spa is shut down. After the problem has been resolved, you must
press any button to reset and restart heater start up. See “Flow Related Checks” below.
Heater is too Hot (OHH)* – M030
One of the water temp sensors has detected 118°f (47.8°C) in the heater and the spa is shut down. You must press any
button to reset when water is below 108°f (42.2°C). See “Flow Related Checks” below.
A Reset Message may Appear with other Messages.
Some errors may require power to be removed and restored.
Flow-Related Checks
Check for low water level, suction flow restrictions, closed valves, trapped air, too many closed jets and pump prime.
On some systems even when spa is shut down, some equipment may occasionally
turn on to continue monitoring temperature or if freeze protection is needed.
* This message can be reset from the topside panel with any button press.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
20
10-08-13
Sensor-Related Messages
READY
RANGE FLTR1
Sensor Balance is Poor – M015
The temperature sensors MAY be out of sync by 2°F or 3°F. Call for Service.
Sensor Balance is Poor* – M026
The temperature sensors ARE out of sync. The Sensor Balance is Poor fault has been established for at least 1 hour.
Call for Service.
Sensor Failure – Sensor A: M031, Sensor B: M032
A temperature sensor or sensor circuit has failed. Call for Service.
Miscellaneous Messages
No Communications
The control panel is not receiving communication from the System. Call for Service.
Pre-Production Software
The Control System is operating with test software. Call for Service.
READY
RANGE FLTR1
°F or °C is replaced by °T
The Control System is in Test Mode. Call for Service.
* This message can be reset from the topside panel with any button press.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
21
10-08-13
System-Related Messages
Memory Failure - Checksum Error* – M022
At Power-Up, the system has failed the Program Checksum Test. This indicates a problem with the firmware (operation
program) and requires a service call.
Memory Warning - Persistent Memory Reset* – M021
Appears after any system setup change. Contact your dealer or service organization if this message appears on more than
one power-up, or if it appears after the system has been running normally for a period of time.
Memory Failure - Clock Error* – M020 - Not Applicable on the BP1500
Contact your dealer or service organization.
Configuration Error – Spa will not Start Up
Contact your dealer or service organization.
GFCI Failure - System Could Not Test/Trip the GFCI – M036
NORTH AMERICA ONLY. May indicate an unsafe installation. Contact your dealer or service organization.
A Pump Appears to be Stuck ON – M034
Water may be overheated. POWER DOWN THE SPA. DO NOT ENTER THE WATER. Contact your dealer or service organization.
A Pump Appears to have been Stuck ON when spa was last powered – M035
POWER DOWN THE SPA. DO NOT ENTER THE WATER.
Contact your dealer or service organization.
* This message can be reset from the topside panel with any button press.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
22
10-08-13
Reminder Messages
General maintenance helps.
Reminder Messages can be suppressed by using the PREF Menu. See Page 11.
Reminder Messages can be chosen individually by the Manufacturer. They may be disabled entirely, or there may be a limited
number of reminders on a specific model.
The frequency of each reminder (i.e. 7 days) can be specified by the Manufacturer.
Press a Temperature button to reset a displayed reminder message.
Alternates with temperature or normal display.
Appears on a regular schedule, e.g. every 7 days.
Check pH with a test kit and adjust pH with the appropriate chemicals.
Alternates with temperature or normal display.
Appears on a regular schedule, e.g. every 7 days.
Check sanitizer level and other water chemistry with a test kit and adjust with the appropriate chemicals.
Alternates with temperature or normal display.
Appears on a regular schedule, e.g. every 30 days.
Clean the filter media as instructed by the manufacturer. See HOLD on page 6.
Alternates with temperature or normal display.
Appears on a regular schedule, e.g. every 30 days.
The Ground Fault Circuit Interrupter (GFCI) or Residual Current Device (RCD) is an important safety device and must be
tested on a regular basis to verify its reliability.
Every user should be trained to safely test the GFCI or RCD associated with the hot tub installation.
A GFCI or RCD will have a TEST and RESET button on it that allows a user to verify proper function.
Warning:
If freezing conditions exist, a GFCI or RCD should be reset immediately or spa damage could result.
The end user should always trained to test and reset the GFCI or RCD on a regular basis.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
23
10-08-13
Reminder Messages Continued
Alternates with temperature or normal display.
Appears on a regular schedule, e.g. every 90 days.
Change the water in the spa on regular basis to maintain proper chemical balance and sanitary conditions.
Alternates with temperature or normal display.
Appears on a regular schedule, e.g. every 180 days.
Vinyl covers should be cleaned and conditioned for maximum life.
Alternates with temperature or normal display.
Appears on a regular schedule, e.g. every 180 days.
Wood skirting and furniture should be cleaned and conditioned per the manufacturers instructions for maximum life.
Alternates with temperature or normal display.
Appears on a regular schedule, e.g. every 365 days.
Filters should be replaced occasionally to maintain proper spa function and sanitary conditions.
Alternates with temperature or normal display.
As needed.
Install new mineral cartridge
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
24
10-08-13
Warning! Qualified Technician Required for Service and Installation
Basic Installation and
Configuration Guidelines
CSA Compliance/Conformité
Caution:
s4ESTTHEGROUNDFAULTCIRCUITINTERRUPTERORRESIDUALCURRENTDEVICEBEFORE
each use of the spa.
Use minimum 6AWG copper conductors only.
Torque field connections between 21 and 23 in lbs.
s2EADTHEINSTRUCTIONMANUAL
Readily accessible disconnecting means to be provided at time of installation.
s!DEQUATEDRAINAGEMUSTBEPROVIDEDIFTHEEQUIPMENTISTOBEINSTALLED
in a pit.
Permanently connected.
s&ORUSEONLYWITHINANENCLOSURERATED#3!%NCLOSURE
Connect only to a circuit protected by a Class A Ground Fault Circuit
Interrupter (GFCI) or Residual Current Device (RCD) mounted at least 5’
(1.52M) from the inside walls of the spa/hot tub and in line of sight from
the equipment compartment.
s#ONNECTONLYTOACIRCUITPROTECTEDBYA#LASS!GROUNDFAULTCIRCUIT
interrupter or residual current device.
s4OENSURECONTINUEDPROTECTIONAGAINSTSHOCKHAZARDUSEONLYIDENTICAL
replacement parts when servicing.
CSA enclosure: Type 2
Refer to Wiring Diagram inside the cover of the control enclosure.
s)NSTALLASUITABLYRATEDSUCTIONGUARDTOMATCHTHEMAXIMUMmOWRATE
marked.
Refer to Installation and Safety Instructions provided by the spa manufacturer.
Warning:
s7ATERTEMPERATUREINEXCESSOFª#MAYBEINJURIOUSTOYOURHEALTH
Warning: People with infectious diseases should not use a spa or hot
s$ISCONNECTTHEELECTRICALPOWERBEFORESERVICING
tub.
Attention:
Warning: To avoid injury, exercise care when entering or exiting the spa
or hot tub.
s4OUJOURSVERIlERLEFlCACITEDUDISJONCTEURDIFFERENTIELAVANTDUTILISER
differentiel avant d’utiliser le bain.
Warning: Do not use a spa or hot tub immediately following strenuous
s,IRELANOTICETECHNIQUE
exercise
s,ORSQUELAPPAREILLAGEESTINSTALLEDANSUNEFOSSEONDOITASSURERUN
drainage adequat.
Warning: Prolonged immersion in a spa or hot tub may be injurious to
your health
s%MPLOYERUNIQUEMENTALINTERIEURDUNECLOTURE#3!%NCLOSURE
Warning: Maintain water chemistry in accordance with the Manufactur-
s#ONNECTERUNIQUEMENTAUNCIRCUITPROTEGEPARUNDISJONCTEURDIFFERENtiel de Class A.
ers instructions.
Warning: The equipment and controls shall be located not less than 1.5
meters horizontally from the spa or hot tub.
s!lNDASSURERUNEPROTECTIONPERMANENTECONTRELEDANGERDESHOCK
electrique, lors de l’entretien employer seulement des pieces de rechange
identiques.
Warning! GFCI or RCD Protection.
s,ESPRISESDASPIRATIONDOIVENTETREEQUIPEESDEGRILLESCONVENANTAU
debit maximal indique.
The Owner should test and reset the GFCI or RCD on a
regular basis to verify its function.
Avertissement:
s$ESTEMPERATURESDELEAUSUPERIEURESAª#PEUVENTPRESENTERUN
danger pour la sante.
Warning! Shock Hazard!
No User Serviceable Parts.
s$ECONNECTERDUCIRCUITDALIMENTATIONELECTRIQUEAVANTELENTRETIEN
Warning/Advertissement:
Do not attempt service of this control system. Contact your
dealer or service organization for assistance. Follow all
owner’s manual power connection instructions. Installation
must be performed by a licensed electrician and all grounding connections must be properly installed.
s$ISCONNECTTHEELECTRICPOWERBEFORESERVICING+EEPACCESSDOORCLOSED
s$ECONNECTERDUCIRCUITDALIMENTATIONELECTRIQUEAVANTLENTRETIEN
Garder la porte fermer.
Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
40940_J
25
10-08-13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement