Bluetooth Sportclip Quick Start Guide

Bluetooth Sportclip Quick Start Guide
Product Application
Bluetooth Sportclip
Quick Start Guide
Operation
Charging the battery
The battery is not fully charged and it is highly recommended that you charge AIS02F
before you begin using it.
Stream music up
to 33’ away
Headphones
Ear buds
Power button,
Answer phone
Smartphone
Tablet
LCD display
Volume buttons
Attached clip
aluratek.com
AIS02F
qsg Q10266
Copyright © 2012 Aluratek, Inc. All Rights Reserved.
Operation
Note: The pairing mode will last 3 minutes. AIS02F will switch to the standby mode automatically if
no devices can be connected within 3 minutes.
Pairing with the transmitter such as iPhone, smart phone, and tablet:
Please make sure the device supports A2DP profile. The pairing procedure will vary
depending on the actual device. Please refer to the user guide of your device for
detail instruction. The general pairing procedures are as follows:
1. Make sure AIS02F is turned Off.
2. Activate AIS02F pairing mode by press and hold the power button for 6-7 seconds.
3. Activate your device’s Bluetooth function and set your device to search for Bluetooth
devices. Select AIS02F when it is found.
4. For transmitter with Bluetooth version 2.1, you will not need to input a code. If you
are prompted for PIN, please enter “0000”.
5. If prompted by your device to connect, please select “Yes”.
6. After connecting successfully, the blue LED will flash twice every 5 seconds.
Note: Please make sure the audio output is set to Bluetooth / AIS02F for audio streaming from the device.
Bluetooth enable your NON
Bluetooth headphones or
earbuds by connecting them
to the Enabler for wireless
audio streaming
Tech Support & Warranty Information
If you need further assistance, please contact the Aluratek support department for
troubleshooting prior to returning this device.
E-mail: [email protected]
Web: www.aluratek.com/support
Local (Tustin, CA): 714-586-8730
Toll free: 1-866-580-1978
Aluratek warrants this product against defect in material or workmanship for
1 Year from the date of purchase.
For more information, please visit: http://aluratek.com/warranty-return-policy
You can register your product online at: http://aluratek.com/product-registration
Note: Using AIS02F “out of the box” will not harm the device. You will experience reduced battery
life as the unit will not be fully charged.
Connect the USB end of the cable provided to your PC and the charger plug to the
charging jack of AIS02F. Please charge the battery for a minimum of (3) hours. The Red
LED will be on while charging. When charging is complete, the red LED will turn off.
Function
Operation
LED Indicator
Power On
Press and hold Power button for
3-5 seconds
Blue LED - 1 second
Power Off
Press and hold Power button for
3-5 seconds
Red LED - 1 second
Ensure AIS02F is turned Off. Press and
hold
button for 6 to 7 seconds until
LED flashes red and blue alternately
LED flashes red and
blue alternately
Enter Pairing
Mode
Radio and TV Interference Statement
WARNING!!! This equipment has been tested and found to comply with the limits of a
Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by whatever measures may be
required to correct the interference.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement