Freestanding_ semi built In 24 and 48 inch .indd

Freestanding_ semi built In 24 and 48 inch .indd
Design Guide 2008
Freestanding / Semi Built In Models 24" and 48"
7082440-01
Welcome
Liebherr's engineering excellence in Germany provides the largest
selection of freezers, refrigerators and wine refrigerators worldwide.
Liebherr appliances consistently specializes in the manufacturing of high
quality freezers and refrigerators. With more than 300 basic models, we have
the widest selection in the world. Liebherr appliances feature premium quality,
numerous innovative product ideas and advanced design. Liebherr freezers and
refrigerators are manufactured at three modern production plants:
Liebherr Marica in Bulgaria, Liebherr-Hausgeräte Ochsenhausen GmbH in
Germany and the Liebherr-Hausgeräte Lienz GmbH in Austria.
We produce more than 2.3 million quality freezers, refrigerators and wine
refrigerators each year, and these are sold all over the world. LiebherrHausgeräte Ochsenhausen GmbH in Germany makes over 1,100,000 appliances
a year and employs 1,900 people. The Liebherr-Hausgeräte Lienz GmbH
manufactures more than 700,000 freezers and refrigerators and employs 1,500
people.
The appliances for the North American market are produced in Austria and in
Germany.
Liebherr is commited to the protection of the environment and recognizes it
as a critical priority. To guarantee an optimum and consistent implementation,
all ecological aspects were observed and integrated into the quality control of
Liebherr in compliance with DIN EN ISO 9001.
Liebherr's Commitment to the Environment
The components of Liebherr products can be recycled when the necessary
resources are applied. A concern for the environment and a desire to protect
resources has lead to increased levels of recycling year after year. When
Liebherr manufactures products, it is essential that the recyclable recovery rate
of the materials we use constantly increases.
Recycling is a common goal among all manufacturers, municipalities and
recycling companies to protect our environment. Protecting the environment
and producing products which have a low impact on the environment, is one
of Liebherr's core values. Whether you are replacing a unit or starting fresh,
remember to dispose of your old appliance in an environmentally safe and
friendly manner.
Introduction
LIEBHERR WARRANTY PLAN
FULL TWO YEAR WARRANTY - For two years from the date of original purchase, your Liebherr Warranty
covers all parts and labor to repair or replace any part of the product which proves to be defective in materials or workmanship.
FULL FIVE YEAR WARRANTY - For five years from the date of original purchase, your Liebherr Warranty
covers all parts and labor to repair or replace any components that prove to be defective in materials or
workmanship in the sealed system. The "Sealed System" means only the compressor, condenser, evaporator, drier and all connecting tubing.
LIMITED 6TH THROUGH 12TH YEAR WARRANTY - From the 6th through 12th year from the date of
original purchase, your Liebherr Warranty covers all parts that prove to be defective in materials or workmanship in the sealed system (parts only).
For Service and Parts in the U.S.:
Liebherr Service Center
Customer Service
If your appliance is not working properly, or if the temperature display reads "F0" to "F5”, please call the
numbers listed below.
Give the fault number displayed, together with the
Type Designation,
Service Number and
Appliance Number (Serial Number)
from the model plate, to ensure prompt, accurate servicing. The model plate is located inside the appliance.
Leave the appliance door closed until the customer service technician arrives to minimize any further cold loss.
15545 N. 77th Street
Scottsdale, AZ 85260
Phone:
Fax:
Toll Free:
(480) 998-0141
(480) 998-7877
1-866-LIEBHERR or
1-866-543-2437
www.liebherr-appliances.com
For Service and Parts in Canada:
Euro-Line Appliances
2278 Speers Rd.
Oakville, Ontario, L6L 2X8
Phone:
Fax:
Toll Free:
(905) 829-3980
(905) 829-3985
1-888-Liebherr,
1-888-543-2437
www.euro-parts.ca
Contents
General Remarks
Safety Warnings
I
Electrical Requirements & Safety
II
IceMaker (if equipped)
III
Area Requirements
IV
Safety Regulations
V
Freestanding/Semi Built In Models
24" and 48" Models: CS13.., SBS26S0
1
Unit Dimensions
2
Cabinet Opening Dimensions
4
Ventilation Requirements
5
Top Door Hinge Clearance CS 13.. - SBS 26S0
6
General Remarks
I. Safety Warnings
PLEASE READ AND FOLLOW THESE INSTRUCTIONS
This design guide contains Warning and Caution statements. This information is important for safe and
efficient installation.
This design guide is not replacing the use and care manual which contains important information on how to use Liebherr appliances.
Always read and follow all Warning and Caution statements!
States a hazard that may cause serious injury or death if precautions are not followed.
Signals a situation where minor injury or product damage may occur if you do not follow instructions.
States a hazard will cause serious injury or death if precautions are not followed.
IMPORTANT
This highlights information that is especially relevant to a problem-free installation.
Make sure incoming voltage is the same as the unit rating.
To reduce the risk of fire, electric shock, or personal injury, the installation work and electrical wiring must be done by
a qualified electrician in accordance with all applicable codes and standards, including fire rated construction.
To the Installer
It is very important that the guidelines and instructions are followed in this design guide to ensure proper installation and operation of the unit. The Installation Guidelines section contains important information for making sure the
installation is correct. Read and understand all the information and installation guidelines in this manual before the
unit is installed.
It is also very important to know the Safety Information.
General Remarks
II. Electrical Requirements & Safety
III. IceMaker (if equipped)
A 115 Volt, 60 Hz, 15 Amp (20 Amp for side-by-side
installation) fused electrical supply is required. Connect
undercounter wine cabinet to a 115 VAC, 10 amp (15
Amp for side-by-side installations) circuit that is controlled by a circuit breaker or fuse.
We recommend using a dedicated circuit for these appliances to prevent electrical overload. Comply with
the National Electrical Code as well as local codes and
ordinances when installing the receptacle.
The icemaker is located in the freezer compartment.
It must be connected to the water supply to function
properly. The appliance must be level for the icemaker to
function properly.
The water pressure must be between 21.8-87.0 psi (1.5-6 bar).
Use a 1/4" OD copper line to connect the water supply to
the solenoid valve. This is not supplied with the refrigerator.
If you have hard water, we recommend you install a
water softener. Also, a filter must be installed if the water
contains solids such as sand. All equipment and devices
used to supply the water to the appliance must comply
with the current regulations for your geographical area.
The power cord is equipped with a three-prong (grounding) plug for your protection against possible shock
hazards. To maintain this protection:
• Do not modify the plug by removing the round grounding prong.
Safety Instructions and Warnings
• Do not use a power cord that is frayed or damaged.
• Do not attach the water source while the appliance is
connected to an electrical outlet.
Do not ground to a gas pipe. Check with a
qualified electrician if you are not sure the
appliance is properly grounded. Do not have
a fuse in the neutral or grounding circuit.
ELECTROCUTION HAZARD
Electrical Grounding Required. This
appliance is equipped with a threeprong(grounding) polarized plug for your
protection against possible shock hazards.
• DO NOT remove the round grounding
prong from the plug.
• DO NOT use a two-prong grounding
adapter.
• DO NOT use an extension cord to connect
power to the unit.
• A shut-off valve, must be installed between the hose
line and the main water supply so that the water supply can be stopped if necessary. Do not install the
shut-off valve behind the refrigeration unit.
• The connection to the water supply may only be made
by a trained and licensed plumber.
• The water quality must comply with the drinking water
regulations for the geographical area where the appliance is located.
• The icemaker is designed exclusively to make ice
cubes in quantities needed by a household and may
only be operated with water appropriate for this purpose.
• All repairs and work on the icemaker may only be done
by customer service personnel or other trained personnel.
• The manufacturer cannot accept liability for damage
caused by equipment or water lines between the solenoid valve and the water supply.
General Remarks
IV. Area Requirements
V. Safety Regulations
Verify the following:
• Floors can support refrigerator’s weight plus approximately 1200 pounds (544 kg) of food weight. Not
all Liebherr products are designed for 1200 pounds
(544 kg) of food. Some units are smaller and total
weights may vary.
The appliance complies with UL250 and CAN/CSA-C
22,2 No. 63 and is designed to cool, freeze, store food
as well as make ice (if equipped). It is designed as a
household appliance. If used commercially, the relevant
regulations on commercial use must be observed.
• Finished kitchen floor height is level. Refrigerator must
be shimmed to the floor level, or levelled, to make
sure, air vents are not obstructed.
• Remove anything attached to the rear or side walls
that can obstruct refrigerator opening.
• Cutout dimensions are accurate.
• Electrical outlet is in correct location.
Do not install this unit next to any other refrigerator or
freezer except another Liebherr model. Liebherr models
are designed to allow side by side installation. They are
equipped with a heating system to eliminate condensation when units are installed side by side. Installing this
unit next to any other refrigerator or freezer can cause
condensation or cause damage to the Liebherr unit.
The appliance is set to operate within specific ambient
temperature limits according to its climate rating. These
temperature limits should not be exceeded. The correct climate rating for your appliance is indicated on the
model plate.
This is explained as follows:
Climate
Rating
Set for Ambient Temperatures of
SN
50°F to 90°F (10°C to 32°C)
N
61°F to 90°F (16°C to 32°C)
ST
61°F to 101°F (16°C to 38°C)
T
61°F to 110°F (16°C to 43°C)
SN-ST
SN-T
50°F to 101°F (10°C to 38°C)
50°F to 110°F (10°C to 43°C)
- The refrigerant circuit has been tested for leaks.
To protect the refrigerator from possible
damage, allow the appliance to stand 1/2 to
1 hour in place before turning the electricity
on. This allows the refrigerant and system
lubrication to reach equilibrium.
Blocking For Safety
The anti-tip brackets must be installed to prevent the
unit from tipping after it is installed.
Freestanding/Semi Built In Models
CS 1301, 1350 - SBS 26S0
24" and 48" Models: CS13.., SBS26S0
The unique design of Liebherr's freestanding models feature fully stainless steel doors, and even stainless steel side walls - a perfect combination of design and functionality. New Swing Line doors with bevelled edges are a particularly elegant feature of this
combination. Practical lever handles with integrated opening mechanisms make opening the appliance almost effortless.
24" and 48" Models
CS 1301
Energy Star:
Energy consumption p. a.:
Energy Supply:
Total capacity:
Refrigerator:
Freezer:
Climate Rating:
Door hinges:
qualified
439 kWh
115V/60Hz/350W
12.3 cu ft (348 L)
9.2 cu ft (260 L)
3.1 cu ft (88 L)
SN-T
left/reversible
• Automatic refrigerator defrosting
• Automatic freezer compartment defrosting
CS 1350
Energy Star:
Energy consumption p. a.:
Energy Supply:
Total capacity:
Refrigerator:
Freezer:
Ice cube capacity:
Ice cube stock:
Climate Rating:
Door hinges:
qualified
439 kWh
115V/60Hz/350W
12.1 cu ft (343 L)
9.2 cu ft (260 L)
2.9 cu ft (83 L)
2.2 pd./24h
3.3 pd.
SN-T
right/reversible
• Automatic refrigerator defrosting
• Automatic freezer compartment defrosting
• Automatic IceMaker can be switched off
SBS 26S0 (CS 1301 & CS 1350)
Energy Supply:
Total capacity:
Refrigerator:
Freezer:
Ice cube capacity:
Ice cube stock:
Climate Rating:
Door hinges:
115V/60Hz/700W
24.4 cu ft (691 L)
18.4 cu ft (520 L)
6.0 cu ft (171 L)
2.2 pd./24h
3.3 pd.
SN-T
left / right
• Automatic refrigerator defrosting
• Automatic freezer compartment defrosting
• Automatic IceMaker can be switched off
1
Freestanding/Semi Built In Models
CS1301, 1350 - SBS 26S0
Unit Dimensions
CS 1301, 1350
A.
B.
C.
D.
E.
F.
G.
2-7/32" (56.5 mm)
78-1/32" (1982 mm)
23-1/2" (597 mm)
25-5/8" (644 mm)
24-7/32" (614 mm)
24-13/16" (631 mm)
46-13/32" (1179 mm)
SBS 26S0 (CS 1301 & CS 1350)
A.
B.
C.
D.
E.
F.
G.
2-7/32" (56.5 mm)
78-1/32" (1982 mm)
47-1/2" (1206 mm)
50-23/32" (1288 mm)
24-7/32" (614 mm)
24-13/16" (631 mm)
46-13/32" (1179 mm)
2
Freestanding/Semi Built In Models
CS 1301, 1350 - SBS 26S0
Cabinet Opening Dimensions
The appliance can be integrated into the kitchen units. To
adapt the appliance to the height of the row of kitchen units, a
suitable top cupboard can be fitted above the appliance.
Unit Venting
DO NOT restrict the air flow. An air flow of at least 2" (50mm)
must be provided. The opening can either be directly over the
appliance or on the back of the cabinet on top of the unit (see
ventilation requirements).
The CS models can be installed in standard 24" deep cabinets.
You will only have to make sure that the door swing clearance
is enough. It is possible to push all CS models to the rear wall
of the cabinet without modification.
When installing the appliance next to a wall, a distance on the
hinge side of 1 27/64 inches (36 mm) minimum is required between the appliance and the wall to allow for the door handle
projection when the door is open.
Minimum Cabinet Opening Dimensions:
CS 1301, 1350
A.
B.
C.
D.
23-3/4" (603 mm)
24" (610 mm)
85" (2159 mm)
80-1/4" (1988 mm)*
SBS 26S0 (CS 1301 & CS 1350)
A.
B.
C.
D.
47-3/4" (1213 mm)
24" (610 mm)
85" (2159 mm)
80-1/4" (1988 mm)*
3"
(76 mm)
*Note: The given cabinet opening height dimension includes 2" for top air vent. If you choose to place the
vent above the cabinet or in a soffit, you will need to adjust the height dimension accordingly.
4
Freestanding/Semi Built In Models
CS 1301, 1350 - SBS 26S0
Ventilation Requirements
This type of cabinet must be carefully constructed using the
correct dimensions and it must provide suitable ventilation to
ensure proper appliance operation.
Kitchen Cabinet Airflow
1. The following ventilation dimensions must be observed:
There must be a ventilation space at least 31 in.² (200 cm²)
at the airflow inlet (1) and at the airflow outlet (2). The 30"
and 60" models are equipped with a rolling base, which is
already providing you with the bottom airflow inlet requirements.
B - Side view
Cabinet
The top ventilation space can be directed in one of the following ways:
A) Directly over the appliance (2) with a gap of at least 2
inches between the ceiling of the unit and the cabinet.
Refrigerator
B) Above the cabinet and below the ceiling (3).
C) Through a vent installed in a soffit (4).
A
B
C
The refrigerator is designed to allow proper air flow when the
appliance is installed up against the wall.
A minimum space of 1 1/2" is required when a cabinet is built
above.
5
Freestanding/Semi Built In Models
CS 1301, 1350 - SBS 26S0
Top Door Hinge Clearance CS 13.. - SBS 26S0
13/64” (5mm)
When installing CS units into a row of cabinets or wall units;
use these dimensions to achieve a custom look with the cabinetry while providing the necessary clearance for the top door
hinge.
6
2-55/64”+1/2”
(73mm+13mm)
28-7/64” (714mm)
78-15/64”+1/2” (1987mm+13mm)
78-1/32”+1/2” (1982mm+13mm)
41/64” (16mm)
46-5/32” (1172mm)
2-7/8” (73mm)
7
Design Guide 2008
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising