ADMIRAL Range/Stove/Oven Fault Codes AMANA Range/Stove/Oven Fault Codes Dual Convection Wall Oven "Big Oven" 5.1 cubic ft. (Sigma Touchmatic ERC) ASKO Dishwasher Dryer Washing Machine CALORIC Range/Stove/Oven Fault Codes RST376 Gas Range Fault Codes CROSLEY DACOR Range/Stove/Oven Fault Codes FRIGIDAIRE Range/Stove/Oven Fault Codes Version 1 Range/Stove/Oven Fault Codes Version 2 Range/Stove/Oven Fault Codes Version 3 Range/Stove/Oven Fault Codes Version 4 GE Gas or Built In Oven Fault Codes XL44 Self Clean Oven Fault Codes "New '99" Range/Stove/Oven Fault Codes Range/Stove/Oven Fault Codes WSL Model Washing Machine Microwave Fault Codes Dishwasher Fault Codes - From Late 1990's forward GIBSON Range/Stove/Oven Fault Codes HAMILTON Range/Stove/Oven Fault Codes HARDWICK HOTPOINT Range/Stove/Oven Fault Codes JENN AIR Range/Stove/Oven Fault Codes Newer Style Range/Stove/Oven Fault Codes KELVINATOR KITCHEN AID Range/Stove/Oven Fault Codes MAGIC CHEF Range/Stove/Oven Fault Codes MAYTAG Gemini Range/Stove/Oven Fault Codes Type "C" and "D" Clocks Range/Stove/Oven Fault Codes Range/Stove/Oven Fault Codes Stackable A/W and Dryer Fault Codes NORGE RCA Range/Stove/Oven Fault Codes ROPER Range/Stove/Oven Fault Codes Range/Stove Oven - Alternative 2 Digit Fault Codes Range/Stove Oven BES, BEP models Range/Stove 24" Built-In Self-Clean Wall Oven SEARS/KENMORE Range/Stove/Oven Manufacturers TAPPAN Range/Stove/Oven Fault Codes THERMADOR Range/Stove/Oven Fault Codes starting with an E Range/Stove/Oven Fault Codes starting with an F WESTINGHOUSE Range/Stove/Oven Fault Codes WHIRLPOOL Whirlpool Polara Range/Stove/Oven Fault Codes Non Y-Line Range/Stove/Oven Fault Codes, Common Range/Stove Oven 30" Free-standing, Models SF3…& 24" Built-In Whirlpool Duet & Duet HT Calypso Washing Machine Calypso Matching Dryer ADMIRAL Range/Stove/Oven Fault Codes Failure Code Condition Check/Repair F1 Defective touch pad or membrane Replace touch pad or clock assembly (also called the ERC) (usually the touch pad) F1 Watchdog on board Replace touch pad or clock assembly (also called the ERC) F2 Oven too hot Replace relay board (if present) or oven temperature sensor F3 or F4 Open or shorted oven temperature sensor Replace oven temperature sensor F5 Hardware and watchdog circuits disagree Replace clock assembly (also called the ERC) F6 Missing AC signal Check for proper voltage F7 Function key shorted or stuck button Replace touch pad or clock assembly (also called the ERC) or un-stick button F8 Analog/Digital trouble Replace clock assembly (also called the ERC) F9 Door latch trouble Check door lock circuit or replace clock assembly (also called the ERC) F0 Function key stuck Replace touch pad or clock assembly (also called the ERC) Back to TABLE OF CONTENTS AMANA Range/Stove/Oven Fault Codes Failure Code - glass link Electronic Range Control (ERC) Condition Check/Repair Door flashing #0, 1, 2, 3 Latch switch broken Replace Lock flashing Latch switch broken Replace F0 Loss of safety signal Replace adapter board F1 Watchdog circuit Replace Electronic Range Control (ERC) F2 Oven too hot Replace oven temperature sensor F3 F4 Open or shorted oven temperature sensor Replace oven temperature sensor F7 Shorted touch panel Replace glass panel F9 Motorized door Check latch FF Lock error Check switch and motor Electronic Range Control (ERC) III / Relay board with separate board / push buttons F0 Shorted push pad Replace F1 Failed Electronic Range Control (ERC) Replace F2 Oven too hot Replace oven temperature sensor F3 F4 Shorted or open oven temperature sensor Replace oven temperature sensor F5, F6, F8 Failed Electronic Range Control (ERC) Replace ERC F7 Shorted or sticking button Check glass alignment, replace touch panel if necessary F9 Door latch failure Replace door latch switch or assembly if necessary Back to TABLE OF CONTENTS AMANA Dual Convection Wall Oven Failure Code Condition Check/Repair F0 Shorted touch pad Replace touch pad F1 Electronic range control failure Replace electronic range control (ERC) F2 Oven temperature 100 degrees over limit Replace oven temperature sensor F3 Shorted oven temperature sensor Replace oven temperature sensor F4 Open oven temperature sensor Replace oven temperature sensor F6 Electronic range control component failure Replace electronic range control (ERC) F7 Failure detected in self-clean lock circuitry Check door latch mechanism Back to TABLE OF CONTENTS AMANA "Big Oven" 5.1 cubic ft. (Sigma Touchmatic ERC) Failure Code Condition Check/Repair F0-0 No Error Initial factory setting F1-1 Over temperature while cooking Check oven temperature sensor and wiring first, replace control board if oven temperature sensor is good F1-3 Over temperature while cleaning Check oven temperature sensor and wiring first, replace control board if oven temperature sensor is good F1-5 Cancel key input out of range Replace control board F1-7 Keyboard disconnected Verify wire connection is tight.Replace control if failed F1-8 Shorted key Replace control board F1-9 Slave micro not functioning Replace control board F1-A Circuit board grounding Replace control board F1-C Control not calibrated Replace control board F1-E Circuit board data corruption Replace control board F1-F Circuit board data corruption Replace control board F1-H Door switch input circuit failure Check switch and wiring F1-J Latch switch input circuit failure Check switch and wiring F3-1 Oven temperature sensor or oven temperature sensor circuit failure Check wire connections and oven temperature sensor F9-1 Auto latch will not lock Check wiring, motor, and latch switch F9-2 Auto latch will not unlock Check wiring, motor, and latch switch Back to TABLE OF CONTENTS Asko Dishwasher Failure Code Condition Check/Repair F1 Water heating fault, selected temperature not reached within 60 minutes · Incoming water temperature too cool · Heating element burned out · Thermostat defective F2 High water level · Plugged/Bad water pump · Defective water inlet valve F3 Thermistor fault · Open thermistor · Bad wiring to thermistor F4 Fault with water fill (only on machines with level-controlled fill) 1. Disconnect the power to the unit Note: Lights blinking, pump running and controls dead indicates an over fill fault 2. Remove the lower access panels and check the tray under the dishwasher (you will probably find it is full of water) 3. Use a towel or a sponge to remove the water 4. There is a float that should stop the operation of the dishwasher and run the pump if water is in this tray. Check this pump to see if it is functional 5. Test the dishwasher 6. If there are no leaks from the dishwasher into the pan, check the drain hose under the sink 7. THE DRAIN HOSE MUST RUN UP TO THE TOP OF THE UNDERSIDE OF THE COUNTERTOP THEN DOWN TO THE DRAIN. (If the hose is not set up like this, water from the sink drain will flow into the dishwasher and overfill the tray *Faults may vary by model. Use this as a general guide. Back to TABLE OF CONTENTS Asko Dryer Failure Code Condition Check/Repair F1 Condensate drain overfilling Check condensate reservoir pump and drain tube. F2 Maximum drying time exceeded (3hrs) · Check for tripped circuit breaker or blown fuse · Check ductwork for lint build-up · Check hi-limit and cycling thermostat · Check heating element F3 Thermistor fault · Open thermistor, replace · Bad wiring to thermistor F4 Too much lint in the lint filter, front housing, or in the condenser Clean lint from lint filter and/or condenser F5 Fault in the moisture sensor · Lint covering sensor in front of housing · Bad sensor · Bad wiring to sensor Back to TABLE OF CONTENTS Asko Washing Machine Failure Code Condition Check/Repair F1 Water supply/low water fill · Check water supply to machine ·Replace water inlet valve F2 Water level too high · Plugged/Bad water pump · Faulty water valve F3 Pump problem Check pump trap and clean. F4 Thermistor problem · Open thermistor, replace · Bad wiring to thermistor F5 Fault in thermal cutout or heating pause fault. Selected temperature not reached in 90 minutes · Check heating element · Check thermostat F6 Motor fault · Check wiring to motor · Replace motor if necessary F7 Door lock release fault · Bent pull-rod for door latch · Bad door latch solenoid 00 00 Machine did not spin Check load for out of balance Redistribute load and restart Back to TABLE OF CONTENTS CALORIC Range/Stove/Oven Fault Codes Failure Code glass link Condition Check/Repair Electronic Range Control (ERC) Door flashing #0, 1, 2, 3 Latch switch broken Replace switch "Lock" flashing Latch switch broken Replace switch F0 Loss of safety signal Replace adapter board F1 Watchdog circuit Replace Electronic Range Control (ERC) F2 Oven too hot Check oven temperature sensor F3 F4 Open or shorted oven temperature sensor Replace oven temperature sensor F7 Shorted touch panel Replace touch panel F9 Motorized door problem Check door latch FF Door lock error Check door switch and latch motor Electronic Range Control (ERC) III / Relay board with separate board / push buttons F0 Shorted touch pad Replace touch pad F1 Failed Electronic Range Control (ERC) Replace ERC F2 Oven too hot Check oven temperature sensor, replace if necessary F3 F4 Shorted or open oven temperature sensor Replace oven temperature sensor F5, F6, F8 Failed Electronic Range Control (ERC) Replace ERC F7 Shorted or sticking button Check glass touch panel alignment, replace if necessary F9 Door latch failure Replace door latch if necessary Back to TABLE OF CONTENTS CALORIC RST376 Gas Range Fault Codes Failure Code Condition Check/Repair F1 Clock bad Replace clock assembly (also called the ERC) F2 Oven temperature sensor defective Replace oven temperature sensor F3 Open oven temperature sensor Replace oven temperature sensor F4 Oven temperature sensor low rating Replace oven temperature sensor F5 Clock failure Replace clock assembly (also called the ERC) F6 Power surge (clock) Try turning off power to appliance for one minute. If problem persists, replace clock assembly (also called the ERC) F7 Touch panel button stuck Replace touch panel (membrane) F8 Failure of diagnostic read-out Replace clock assembly (also called the ERC) Back to TABLE OF CONTENTS DACOR Range/Stove/Oven Fault Codes Failure Code Condition Check/Repair F0 Clock pushbutton is stuck in a depressed position Check clock buttons F1 Element relay circuit failure Control board may be bad F2 Oven temperature exceeded the clean runaway temperature (self clean only) or the cooking runaway temperature (cooking modes only) Call for service F3 Short Circuit in the oven temperature sensor Check oven temperature sensor for continuity, if no resistance (zero ohms), replace F4 Short Circuit in the oven temperature sensor Check oven temperature sensor for continuity, if no resistance (zero ohms), replace F6 Failure in the EEPROM check comparison (only time of day and timer will operate) Call for service, electronic clock control is usually the cause of the problem F7 Failure of the self- clean automatic door latch system Check door latch and switch(es) F8 Failure of the door latch motor. Occurs when the motor runs for two minutes without the door locking in self-clean mode Check door lock motor and door latch Back to TABLE OF CONTENTS FRIGIDAIRE Range/Stove/Oven Fault Codes Version 1 Failure Code Condition Check/Repair F2 Oven temp is above design specifications Oven temp has risen above 665F and door unlocked or above 965F with door locked. Check oven temperature sensor. F3 The oven temperature sensor is open Check for open wire connection between EOC (Electronic Oven Control - Clock) and the oven temperature sensor. Replace sensor if no wiring problem. F4 The oven temperature sensor is shorted Check for shorted wire and/or connections between the EOC (Electronic Oven Control - Clock) and the oven temperature sensor. Replace sensor if no wiring problem. F5 The watchdog is active when it should be off Microprocessor checking the operation of the EDC relay, after selection of bake, broil, or clean operation. Relay failed this check. F6 No 60 Hz time base 60 Hz time base is required for time controlled cycling. Replace EDC. F7 Lock motor relay watchdog circuit is active when it should be off Microprocessor checking the operation of the EDC lock, relay failed. Replace EDC. F8 Lock motor relay watchdog is active when it should be off Microprocessor checking the operation of the EDC lock relay after self clean is selected, relay failed. Replace EDC. Back to TABLE OF CONTENTS FRIGIDAIRE Range/Stove/Oven Fault Codes Version 2 Failure Code Condition Check/Repair F0 & F1 EOC (Electronic Oven Control) failure Replace F2 Oven too hot Check Bake function F3 Oven temperature sensor open Check oven temperature sensor, 1100 ohms F4 Oven temperature sensor shorted Replace component F5, 6, 7 EOC (Electronic Oven Control) failure Replace component F8 Lock switches Check or Replace component Back to TABLE OF CONTENTS FRIGIDAIRE Range/Stove/Oven Fault Codes Version 3 Failure Code Condition Check/Repair F0 & F1 EOC (Electronic Oven Control) failure Replace EOC (Electronic Oven Control) F2 Oven too hot Likely a bad oven temperature sensor (should read 1100 ohms) Possible bad EOC (Electronic Oven Control) F3 Oven temperature sensor open Replace oven temperature sensor F4 Oven temperature sensor shorted Replace oven temperature sensor F5 or F6 or F7 EOC (Electronic Oven Control) failure Replace EOC(Electronic Oven Control) Back to TABLE OF CONTENTS FRIGIDAIRE Range/Stove/Oven Fault Codes Version 4 Failure Code Condition Check/Repair F1 Circuit board defective Replace control board F2 1. The oven temp has risen above 665F and the door is not locked or 2. The temp has risen above 965F with the door locked 1. Check oven temp in mode that failure occurred. Replace EOC (Electronic Oven Control) if above limits 2. Check 8-pin connector. Check and replace oven temperature sensor if necessary F3 Oven temperature sensor is open (above 3000 ohms) Check resistance of oven temperature sensor, check for open wiring between oven temperature sensor and control F4 Oven temperature sensor is Check resistance of oven temperature shorted (below 500 ohms) sensor, check for shorted wiring between oven temperature sensor and control F5 Internal watchdog circuit has detected a failure Defective EOC (Electronic Oven Control) F6 Shorted buttons Check push buttons and dome switches on control F8 Logic interrupted (lock motor switch sequence) Check door lock switches and wiring Back to TABLE OF CONTENTS GE Gas or Built In Oven Fault Codes Failure Code Condition Check/Repair F0 or F1 Failed transistor in control If code cannot be cancelled, replace the Electronic Range Control (ERC) or touch pad F2 Oven over temp - exceeded 590F with door in unlocked position or 990F with door locked If actual temp condition occurred, look for welded relay contacts or high resistance connection or any cause in the oven temperature sensor circuit F3 Open oven temperature sensor circuit Measure oven temperature sensor circuit at oven temperature sensor (should be approx 1100 ohms at room temp); check for cut or pinched wire or loss of contact F4 Shorted oven temperature sensor circuit Same as above; check for melted connector or both leads shorted to ground F8 Component failure within Electronic Range Control (ERC) effecting temp processing circuits Replace Electronic Range Control (ERC) F9 Problem with door lock circuit such as pinched wire between Electronic Range Control (ERC) and door lock switch Check wiring and test operation of switch Back to TABLE OF CONTENTS GE XL44 Self Clean Oven Fault Codes Failure Code F0 - F1 F7 Condition Stuck keypad may mean relay is turned on. Check/Repair Determine if problem is with the Key Panel or Control by: 1. Pushing CLEAR/OFF pad. 2. Disconnecting Ribbon Cable from control and waiting at least 32 seconds to see if Code recurs If code recurs, problem is in the control. Replace control. If code does not recur, problem is with the Key Panel. F2 Note: Also see fan thermal Indicates that oven is over temperature in one of the following modes within either a cooking or clean mode of operation. · Look for welded relay contacts. (Heating elements on in off mode). · Look for open thermal switch in lock motor circuit. Switch is normally closed switches · Control senses oven temperature above 650 degrees F with the door circuit in the unlock mode. · Control senses oven temperature above 935 degrees F with the door in the locked mode. · Stalled cooling fan or airflow problem. and will open if area overheats due to fan not operating. Look for cause - fan thermal switch not closing, fan stalled, etc. · Look for high resistance in the oven temperature sensor circuit due to high contact resistance (poor terminal crimp, deformed terminals, loose connection) or intermittent solder joint on control or intermittent oven temperature sensor. · Look for electrical noise interference in the oven temperature sensor circuit (Ham radio, cordless phone, etc.). F3 - F4 Open oven temperature sensor (circuit) (over 2700 ohms) or, shorted oven temperature sensor. Could be a result of: · · contamination on terminals · pinched wire in oven Measure oven temperature sensor resistance at oven temperature sensor connector (take care not to damage terminals in block) - Should read 1100 ohms at room temperature (approx 72 degrees F). temperature sensor circuit · cold solder joint on control. Disconnect power to range and remove oven temperature sensor connector from control. · · Measure each oven temperature sensor lead from connector block to ground. If shorted, look for pinched or cut wire in oven temperature sensor circuit. · Check connector terminals - Look for deformed or corrosion on terminals. Repair or replace. If all above is ok replace control. F5 Relay safety circuit failure · Check oven temperature sensor circuit for intermittent high resistance. · Check lock circuit · Press Clear/Off and reprogram control. If code reappears, replace control Note: If all above check OK the F5 code can be a result of a momentary loss of power (Do NOT replace control or lock, check lock circuit) FC Problem with door lock circuit such as pinched wires between control and door lock switches on motorized lock circuits. Check wiring and test operation of switches. FD Shorted meat probe · Check probe. Resistance should be 30k ohms to 50k ohms at room Note: Problem can be with the probe or receptacle or meat probe temperature. circuit. Look for pinched wire. · · Look for condensation or contamination of receptacle or nearby installation. FF Loss of door motor safety circuit Replace control Back to TABLE OF CONTENTS GE "New '99" Range/Stove/Oven Fault Codes Failure Condition Check/Repair Code FFF Control Error, Failed EEPROM Replace Control F0 or F7 Shorted Clear/Off Key due to membrane switch, control or connector Shorted key panel membrane switch; Check Electronic Range Control (ERC) F2 During Bake Control senses oven temp above 590 degrees F High resistance connection in oven temperature sensor circuit. Check Electronic Range Control (ERC) - Welded bake relay contacts F2 During Clean Control senses oven temp above 915 degrees F High resistance connection in oven temperature sensor circuit. Check Electronic Range Control (ERC) - Welded clean relay contacts. Both lock switch 1 & 2 closed at the same time F3 Open oven temperature sensor, oven temperature sensor resistance exceeds 2900 ohms during bake, broil or clean Oven temperature sensor/Oven temperature sensor circuit connections F4 Shorted oven temperature sensor, oven temperature sensor resistance less than 2900 ohms during bake, broil or clean Oven temperature sensor/oven temperature sensor circuit connections FFF Door motor safety circuit Electronic Range Control (ERC) Back to TABLE OF CONTENTS GE Range/Stove/Oven Fault Codes Failure Code Condition Check/Repair F0 and F1 Failed Thermistor Control Replace Electronic Range Control (ERC) F2 Oven temp exceeds 590 w/ unlocked door High resistance or interference in oven temperature sensor. Replace oven temperature sensor F3 Open oven temperature sensor circuit Replace oven temperature sensor F4 Shorted wire (Oven temperature sensor) Locate and correct F7 A = Function pad button stuck or B = Bad clock Unstick button or Replace Electronic Range Control (ERC) F8 Component Failure Replace Electronic Range Control (ERC) F9 Program w/ door circuit Check wiring Back to TABLE OF CONTENTS GE WSL Model Washing Machine Failure Code Condition Check/Repair IE - Water level sensor error Water sensor fails to send signal for longer than 5 seconds. Press POWER button. No other buttons work: · Check wiring harness · Check pressure sensor switch · Check circuit board 7E - Water supply error No frequency change for 60 minutes from water supply. Press POWER button. No other buttons work: · Check wiring harness · Check water valve· Check pressure sensor switch · E - Drain pump error Check circuit board Water level does not decrease to reset point within 15 minutes from draining water from the washer. Press POWER button. No other buttons work: dE - Lid open error Lid is open during wash cycle. Close lid. UE Unbalance switch error Unbalanced load is sensed three times during a spin operation. OE - Water overflow error Water supply does not stop after sensing an overflow condition. · Check wiring harness · Check pump motor · Check circuit board · Check wiring harness · Check lid switch · Check unbalance switch · Check circuit board Open lid. Rebalance laundry load and close lid. · Check wiring harness · Check unbalance switch · Check circuit board Turn off household water supply to washer and unplug power cord. · Check wiring harness · Check water inlet valve · Check pressure sensor switch · Check circuit board Back to TABLE OF CONTENTS GE Microwave Fault Codes Failure Code Condition Check/Repair F1 Open sensor, will occur below 190F of cavity temperature within 15 minutes after starting convection, combination or roast cook Check oven temperature sensor for continuity. Replace if zero or infinite ohms F2 Shorted thermal sensor, will occur if a shorted thermal sensor is detected continuously over 5 seconds on convection, combination or roast cooking Check oven temperature sensor for continuity. Replace if zero or infinite ohms F3 Shorted key panel (touch pad), will occur if a shorted key panel is detected continuously over 60 seconds Replace key panel (touch pad) F4 Open humidity sensor, will occur if humidity sensor is detected as being open continuously over 5 seconds Replace humidity sensor Note: It will take a minimum of 5 minutes of convection run time before F1 or F2 code will be displayed if the thermal sensor is shorted or open. F5 Shorted humidity sensor, will occur if humidity sensor is detected as being shorted continuously over 5 seconds Replace humidity sensor F6 Shorted temperature probe, will occur if temperature probe is detected as shorted continuously over 5 seconds Replace temperature probe ProbEe Open temperature probe, will occur if If probe is plugged in and "ProbE" is temperature probe is detected open, or on display check continuity of the not plugged into the receptacle probe with an ohm meter. If zero or infinite ohms, replace it Back to TABLE OF CONTENTS GE Dishwasher Fault Codes - From Late 1990's forward Failure Code Condition Check/Repair PF Power Failure Push cancel to clear. If code persists check electrical connections to dishwasher and electronic control C1 Partially restricted drain, pump-out not accomplished in the normal time of less than 95 seconds Check drain line, if clear, check for a restricted drain valve in pump C2 Drain line totally blocked, pump-out not accomplished in the maximum time of 405 seconds Check drain valve for restriction in pump, check drain line. Note: If a new garbage disposer was installed, remove knock out plug for dishwasher drain C3 Will not go into drain Call for service C4 Water over-fill fault Check for high water pressure to unit, usually an indication of a bad water inlet valve C5 Low water fill Check for low water pressure to unit, usually an indication of a bad water inlet valve C6 Water temperature too low after 20 minute extension Check heating element and thermostat, both should have continuity C7 Temperature sensor bad Replace sensor (located inside door, remove door panel to access) C8 Detergent cup blocked Keep objects clear of cup when loading Back to TABLE OF CONTENTS GIBSON Range/Stove/Oven Fault Codes Failure Code Condition Check/Repair F0 & F1 EOC (Electronic Oven Control) failure Replace EOC (Electronic Oven Control) F2 Oven too hot Likely a bad oven temperature sensor Possible bad EOC (Electronic Oven Control) F3 Oven temperature sensor open Replace oven temperature sensor F4 Oven temperature sensor shorted Replace oven temperature sensor F5 or F6 or F7 EOC (Electronic Oven Control) failure Replace EOC (Electronic Oven Control) Back to TABLE OF CONTENTS HAMILTON Range/Stove/Oven Fault Codes Self-Clean Convection Freestanding Failure Code Condition Check/Repair F0 Stuck CLEAR/OFF touch pad switch Unstick switch or replace keypad F1 Stuck relay on circuit board Replace board F2 Control senses oven temp, over Test oven temperature sensor for 615F with door unlocked, over continuity, replace if necessary. If oven 9615F with door locked (self clean) temperature sensor is OK, replace circuit board F3 Oven temperature sensor circuit open Replace oven temperature sensor F4 Oven temperature sensor circuit shorted Replace oven temperature sensor F5 Loss of internal timer safety in the heating mode in bake/broil Check circuit board, replace if necessary F7 Shorted touch pad switch, any except up/down arrow and clear/off pads Replace touch pad FC Door latch error Check door latch FD Shorted meat probe, jack or wires Check wiring harness and meat probe jack. FF Loss of door lock circuit protection Check door lock circuit switch, wiring and circuit board. Back to TABLE OF CONTENTS HOTPOINT Range/Stove/Oven Fault Codes Failure Code Condition Check/Repair F0 and F1 Failed Thermistor Control Replace Electronic Range Control (ERC) F2 Oven temp exceeds 590 w/ unlocked door High resistance or interference in oven temperature sensor, replace sensor F3 Open oven temperature sensor circuit Replace oven temperature sensor or, check for an open oven temperature sensor fuse, replace fuse. F4 Shorted wire (oven temperature sensor) Locate and correct F7 A = Function pad button stuck or B = Bad clock Unstick button or replace Electronic Range Control (ERC) clock assembly F8 Component Failure Replace Electronic Range Control (ERC) F9 Program w/ door circuit Check wiring Back to TABLE OF CONTENTS JENN AIR Range/Stove/Oven Fault Codes Failure Condition Check/Repair Code F1 Defective touch pad or membrane Replace touch pad or membrane (this problem is usually the touch pad) F1 Watchdog on board Replace touch pad or clock assembly (also called the ERC) F2 Oven too hot Replace relay board (if present) or oven temperature sensor F3 or F4 Open or shorted oven temperature sensor Replace oven temperature sensor F5 Hardware and watchdog circuits disagree Replace clock assembly (also called the ERC) F6 Missing AC signal Check for proper voltage F7 Function key shorted or stuck button Replace touch pad or clock assembly (also called the ERC) or attempt to unstick button F8 Analog/Digital supervisory Replace clock assembly (also called the ERC) F9 Door latch supervisory Check door lock circuit or replace clock assembly (also called the ERC) F0 Function key stuck Replace touch pad or clock assembly (also called the ERC) Back to TABLE OF CONTENTS JENN-AIR 'Newer Style' Range/Stove/Oven Fault Codes Failure Code F1 Condition Power to element relay energized during time of day display Check/Repair Wiring harness shorted or change power relay board (PRB) Note: for double ovens, change second oven board F2 Oven temp sensed; over 600F sensed by control in time of day mode, bake mode, or over 900F sensed in clean mode. Ohm test the oven temperature sensor, if OK, change power relay board. F3 Cooling fan on with no oven function selected Check oven temperature sensor or wire harness to oven temperature sensor F4 Shorted oven temperature sensor Check oven temperature sensor or wire harness to oven temperature sensor F5 Power to element relays disabled in cook mode 1. Intermittent oven temperature sensor or wire harness or, 2. Intermittent contact on power relay board F7 Shorted key sensed for 32 seconds 1. Membrane shorted, or, 2. Display board defective F8 Shorted meat probe alarm 1. Probe jack or harness to probe jack, or, 2. Probe sensing temp above 250F F9 Door lock safety circuit on power relay board sensed Replace power relay board FF Invalid temp reading on power relay board (PRB) Check oven temperature sensor and wire harness, or replace power relay board F Communication error between boards Wiring harness, check harness wires for continuity, or replace power relay board FC Communication error between boards Wiring harness or power relay board (PRB) FR Second oven error sensed 1. Check oven temperature sensor and harness, or, 2. Replace second board Back to TABLE OF CONTENTS KITCHEN AID Range/Stove/Oven Fault Codes NOTE: Not valid for Y line. If there is a Y near the end of your model number, do not use this chart. Failure Code Condition Check/Repair 4 Digit Failure Code F0 - E0 Analog to Digital Failure Disconnect for 30 seconds - if display re-appears - replace control F1 - E1 Safety flip flop Replace Electronic Range Control/Clock(ERC) F2 - E0 Shorted keypad Replace Electronic Range Control/Clock(ERC) F3 - E0 Oven temperature sensor or oven temperature sensor fuse opened Replace oven temperature sensor or fuse F3 - E1 Oven temperature sensor shorted Replace oven temperature sensor F3 - E2 Oven too hot Replace oven temperature sensor F3 - E3 Clean temp too hot Replace oven temperature sensor F5 - E0 F5 - E1 and E2 Check door/latch switch Replace component 2 Digit Failure Code F0 or F1 or F5 Failed transistor Replace Electronic Range Control/Clock(ERC) F2 - E0 Oven temp too high 1. Test operation of door lock on selfclean models 2. Test relay contact operation 3. High resistance in oven temperature sensor F3 Open oven temperature sensor or thermal fuse Replace oven temperature sensor or thermal fuse F4 Shorted oven temperature sensor Replace oven temperature sensor F6 Problem in time keeping circuit 1. Reset time and/or cooking operation 2. Check for proper ground F7 Stuck function switch or button Replace Electronic Range on Electronic Range Control (ERC) Control/Clock(ERC) F8 Failure of Electronic Range Control (ERC) Replace Electronic Range Control/Clock(ERC) F9 Door lock circuit Check wiring and test operation of door lock switch Back to TABLE OF CONTENTS MAGIC CHEF Range/Stove/Oven Fault Codes Failure Code Condition Check/Repair F1 1. Watchdog on board 2. Touch membrane defective To determine which component is at fault, disconnect ribbon strip. If NO fault code, replace membrane, otherwise replace board F2 Oven too hot Check oven temperature sensor F3 F4 Open or shorted oven temperature sensor Replace F5 Hardware and watchdog circuits disagree Replace clock assembly (also called the ERC) F6 Missing AC signal Replace clock assembly (also called the ERC) F7 Function key shorted Replace touch pad F8 Analog/Digital converter Replace clock assembly (also called the ERC) F9 Door latch Check door lock circuit F10 Function key stuck Replace touch pad Back to TABLE OF CONTENTS MAYTAG Gemini Range/Stove/Oven Fault Codes Failure Code Condition Check/Repair F0:-0 None F1:-1 Runaway Cook Upper oven Check oven temperature sensor, replace if necessary F1:-2 Runaway Cook Lower oven Check oven temperature sensor, replace if necessary F1:-3 Runaway Clean Upper oven Check oven temperature sensor, replace if necessary F1:-4 Runaway Clean Lower oven Check oven temperature sensor, replace if necessary F1:-5 Keypad Cancel Upper Check keypad, replace if necessary F1:-6 Keypad Cancel Lower Check keypad, replace if necessary F1:-7 Keypad Disconnected Check wiring between keypad and Electronic Range Control (ERC) F1:-8 Keypad Shorted Check to see if steam or other moisture is getting into clock assembly. Replace keypad if necessary F1:-9 Slave F1:-A Latch Switch, Upper Check door latch switches, replace if necessary F1:-B Latch Switch, Lower Check door latch switches, replace if necessary F1:-C Door Switch, Upper Check door switch, replace if necessary F1:-D Door Switch, Lower Check door switch, replace if necessary F1:-E EEPROM, Control Replace Electronic Range Control (ERC) F1:-F Jumper, Control F1:-H EEPROM, Read, Control Replace Electronic Range Control (ERC) F1:-L Oven temperature sensor, Track, Control Check oven temperature sensor, replace if necessary F3:-2 Oven temperature sensor, Lower oven Check oven temperature sensor, replace if necessary F3:-1 Oven temperature sensor, Upper oven Check oven temperature sensor, replace if necessary F9:-1 Latch Lock Upper Check for obstruction in door lock mechanism F9:-2 Latch, Unlock Upper Check for obstruction in door lock mechanism F9:-3 Latch Both Upper Check for obstruction in door lock mechanism F9:-4 Latch, Lock Lower Check for obstruction in door lock mechanism F9:-5 Latch Unlock Lower Check for obstruction in door lock mechanism F9:-6 Latch, Both Lower Check for obstruction in door lock mechanism Back to TABLE OF CONTENTS MAYTAG Type "C" and "D" Clocks Range/Stove/Oven Fault Codes Failure Code Condition Check/Repair F1 Supervisory relay enable shorted (noncook mode); sounds alarm and inhibits cook mode if alarm fault monitor is always active in non-cook mode, and requires removal of power until serviced. Usually a bad touch pad or clock assembly (also called the ERC). Replace touchpad or ERC F2 Bake/broil/clean temp runaway alarm; sounds alarm and resets control to noncook mode when bake/broil/clean temp exceeds programmed limits. Usually means a stuck relay. Electric @ 525F (bake), 640F(broil), 900F(clean) Gas @ 525F (bake), 640F(broil), 900F(clean) F3 Open temp oven temperature sensor; sounds alarm and inhibits cook mode Replace oven temperature sensor F4 Shorted temp oven temperature sensor; sounds alarm and inhibits cook mode Replace oven temperature sensor F5 Supervisory relay enable open (cook mode); sounds alarm and resets the control to non-cook mode Replace electronic range control (ERC) F5 Missing a/c line cycle detector; displays code (no audible) Unplug appliance for two minutes, should clear problem F7 Function key shorted; too hot at the clock assembly (also called the ERC) or shorted touch pad or clock assembly (also called the ERC) Replace touchpad or ERC F8 Analog/Digital supervisory; sounds alarm to non-cook mode Replace ERC F9 Door latch supervisory (door latched) Unlock door and check switches or clock assembly (also called the ERC) F0 Cancel key supervision Requires the removal of power until serviced. See qualified technician Back to TABLE OF CONTENTS MAYTAG Range/Stove/Oven Fault Codes Failure Code Condition Check/Repair F1 Defective touch pad or membrane Replace touch pad or membrane (usually the touch pad)* F1 Watchdog on board Replace touch pad or clock assembly (also called the ERC) F2 Oven too hot Replace relay board (if present) or bad oven temperature sensor F3 or F4 Open or shorted oven temperature sensor Replace oven temperature sensor F5 Hardware and watchdog circuits disagree Replace clock assembly (also called the ERC) F6 Missing AC signal Check for proper voltage F7 Function key shorted or stuck button Replace touch pad or clock assembly (also called the ERC) or un-stick button F8 Analog/Digital supervisory Replace clock assembly (also called the ERC) F9 Door latch supervisory Check door lock circuit or replace clock assembly (also called the ERC) F0 Function key stuck Replace touch pad or clock assembly (also called the ERC) * Here is a simple test that you can do to determine whether the clock or the touchpad are defective when the display reads F1: - Disconnect power to the range. - Gain access to the back of the ERC (electronic range control, or "clock"). - Unplug the touch pad ribbon connector from the ERC. This will be a flat wire about 1 ½" to 2" wide. - Make sure everything is clear and will not short out when power is turned back on. Replace any covers removed to gain access to the ERC. - Turn the power back on to the range. - Watch for the F-1 and listen for the beep. - If you get the F-1 and beep, replace the ERC. - If after approximately 60 Minutes you do not get the F-1 fault, replace the touch pad. NOTE: Some models incorporate the touch pad and the clock control as one part so F1 = bad clock control. Warning: If you do not feel comfortable doing this test or making this repair please contact a qualified appliance repair technician. Back to TABLE OF CONTENTS MAYTAG Stackable A/W and Dryer Fault Codes Failure Code Condition Check/Repair "L" persists in washer display Lid lock failure Replace switch, linkage, lock solenoid or control board. 1E persists in washer display Lid lock failure Replace lid lock switch or control board. 9E appears in dryer display Door switch failure Check door switch wiring or door switch or control board "U" occurs for no Unbalanced load Unbalance switch or control board reason in display 6E appears in dryer display Temp control error Ambient (room) temperature too cool, -or- · thermistor · wire harness · control board 7E appears in dryer display Temp control error overheating Check: 8E appears in dryer display Motor relay circuit Check: · venting for restriction · thermistor · control board · cycling thermostat (regular) · relay coil · wire harness or · control board Back to TABLE OF CONTENTS RCA Range/Stove/Oven Fault Codes Failure Code Condition Check/Repair F0 and F1 Failed Thermistor Control Replace Electronic Range Control (ERC) F2 Oven temp exceeds 590F w/ unlocked door High resistance or interference in oven temperature sensor. Likely a bad oven temperature sensor F3 Open oven temperature sensor circuit Replace oven temperature sensor or open oven temperature sensor fuse F4 Shorted wire (oven temperature sensor) Locate and correct F7 A = Function pad button stuck or B = Bad clock Unstick button or Replace clock assembly (also called the ERC) F8 Component Failure Replace Electronic Range Control (ERC) F9 Program w/ door circuit Check wiring Back to TABLE OF CONTENTS ROPER Range/Stove/Oven Fault Codes NOTE: Not valid for Y line. If there is a Y near the end of your model number, do not use this chart. Failure Code Condition Check/Repair 4 Digit Failure Code F0 - E0 Analog to Digital Failure Disconnect for 30 seconds - if display reappears - replace control F1 - E1 Safety flip flop Replace Electronic Range Control/Clock (ERC) F2 - E0 Shorted keypad Replace Electronic Range Control/Clock (ERC) F3 - E0 Oven temperature sensor or oven temperature sensor fuse opened Replace oven temperature sensor or fuse F3 - E1 Oven temperature sensor shorted Replace oven temperature sensor F3 - E2 Oven too hot Replace oven temperature sensor F3 - E3 Clean temp too hot Replace oven temperature sensor F5 - E0 F5 - E1 and E2 Door latch problem Check door/latch switch, replace if necessary 2 Digit Failure Code F0 or F1 or F5 Failed Electronic Range Control (ERC) Replace Electronic Range Control/Clock (ERC) F2 - E0 Oven temp too high 1. Test operation of door lock on selfclean models 2. Test relay contact operation 3. High resistance in oven temperature sensor F3 Open oven temperature sensor or thermal fuse, bad oven temperature sensor harness, or oven temperature sensor resistance too high Replace oven temperature sensor or thermal fuse F4 Shorted oven temperature sensor Replace oven temperature sensor F6 Problem in time keeping circuit 1. Reset time and/or cooking operation 2. Check for proper ground F7 Stuck function switch or button on Electronic Range Control (ERC) Replace Electronic Range Control/Clock (ERC) F8 Failure of Electronic Range Control (ERC) Replace Electronic Range Control/Clock (ERC) F9 Door lock circuit Check wiring and test operation of door lock switch DOOR Bake or Broil Replace latch switch if defective.Replace wire from 10-pin connector if defective · · Defective latch switch Shorted wire from ERC 10-pin connector, pin 10 to ground · DOOR Door latched Self-Clean · · Defective latch switch Replace latch switch if defective.Replace wire from 10-pin connector if defective Open wire from ERC 10-pin connector, pin 10 to ground · LOCK Door not latched Not in Self-Clean · Oven temperature sensor resistance too high Check oven temperature sensor resistance, wire harness and connections, replace defective component Back to TABLE OF CONTENTS ROPER Range/Stove Oven- Alternative 2 Digit Fault Codes Failure Code F1 Condition Analog to Digital Failure Check/Repair Disconnect for 30 seconds - if display re- appears - replace control F1 Safety flip flop Replace component F1 Shorted keypad Replace component F3 Oven temperature sensor opened Measure oven temperature sensor resistance, should be1100 ohms. If not, replace sensor F2 Oven temperature sensor shorted Replace oven temperature sensor F3 Oven too hot Replace oven temperature sensor F3 Clean temp too hot Replace oven temperature sensor F5 Check door/latch switch Replace component Back to TABLE OF CONTENTS ROPER Range/Stove Oven BES, BEP models Failure Code F2 Condition Bake/Clean temperature runaway alarm Check/Repair 1. Allow unit to sit for one hour to cool down 2. Place oven temperature sensor in a glass of ice water 3. Measure oven temperature sensor resistance. The oven temperature sensor should measure about 1000 ohms while in the ice water · If the oven temperature sensor is good but the problem remains replace the electronic range control (ERC) · If the oven temperature sensor is bad, replace it F3 Oven temperature sensor circuit open Verify the oven temperature sensor wiring harness is OK, if so, replace the oven temperature sensor. F4 Shorted oven temperature sensor circuit Verify the oven temperature sensor wiring harness is OK, if so, replace the oven temperature sensor. F5 Element relay enable on. (STUCK CLOSED) Replace the electronic range control (ERC) F6 Power was interrupted Push the OFF/CANCEL button F8 Improper door lock points 1. Check the door latch switch 2. Check the 8-pin connector on the control for a good connection Replace the electronic range control (ERC) if the connections and latch switch check out OK. Back to TABLE OF CONTENTS Roper Range/Stove 24" Built-In Self-Clean Wall Oven Failure Code F2 Condition Oven temperature above specifications Check/Repair 8-pin connector oven temperature sensor to the Electronic Range Control (ERC) F3 Open oven temperature sensor Check wiring harness, replace oven temperature sensor if necessary F4 Shorted oven temperature sensor Check wiring harness, replace oven temperature sensor if necessary F5 Pushbutton stuck Check for binding of pushbuttons and control panel glass. If OK, replace touch panel F6 Computer logic interrupted (timing) Replace Electronic Range Control (ERC) F7 Computer logic interrupted (lock motor) Replace Electronic Range Control (ERC) F8 Computer logic interrupted Replace Electronic Range Control (ERC) Back to TABLE OF CONTENTS SEARS/KENMORE Range/Stove/Oven Manufacturers Sears is a department store. They do not build their own appliances. They contract with many different manufacturers to build all of their appliances. This chart will help you determine who actually built your appliance, then you can choose the manufacturer from the charts on this page. The first 3 digits of the model number determine who built it. Roper Whirlpool Caloric Kelvinator Gibson D&M 103 647 835 911 155 106 110 562 665 198 174 960 417 662 628 253 587 GE Speed Queen Maytag Litton Toshiba Fedders 363 362 651 925 747 562 484 Amana WCI Tappan Jenn Air 596 790 791 629 Back to TABLE OF CONTENTS TAPPAN Range/Stove/Oven Fault Codes Failure Code Condition Check/Repair F0 & F1 EOC (Electronic Oven Control) failure Replace Electronic Oven Control F2 Oven too hot Check Bake function, if OK, replace oven temperature sensor F3 Oven temperature sensor open Check oven temperature sensor, should be ~1100 ohms at room temperature. If too high or low, replace oven temperature sensor F4 Oven temperature sensor shorted Replace oven temperature sensor F5, 6, 7 EOC (Electronic Oven Control) failure Replace Electronic Oven Control F8 Check switches and replace if necessary Lock switches Back to TABLE OF CONTENTS THERMADOR Range/Stove/Oven Fault Codes starting with an E If an error code appears in the cook mode window Your oven is equipped with an extremely reliable and accurate electronic control. On the rare occasion that something occurs that causes a malfunction, an error message will appear in the oven selector window. Some errors (E1, E9, E11, E12, and E13) must be cleared by turning off the oven at the circuit breaker and then turning it back on. When an error remains displayed steadily in the off position, after attempting to clear the error, a service call is required. Have the error code available when you call for service. This will help service determine the problem. Error Code Notes Check/Repair E1 C, E Control board problem E2 K, G Cook or clean mode runaway E3 A, H Open oven temperature sensor (over 5000 ohms) E4 A, H Shorted oven temperature sensor (under 500 ohms) E5 K, D Control board too cold or too hot, or defective board. E6 C, J Control board problem E7 A, I Illegal temp display turn off and retry E8 A, D Control board problem E9 A, E Latch switch problems E10 B, D Control board problem E11 A, F CT oven; latch switch problem E12 A, E CT oven; latch switch problem E13 A, C CT ovens; latch froze or no power to latch motor CMT ovens; control board not converted E14 A, E Latch switch problems E15 B, D Control board problem Notes A Turns heat off on failed oven only, micro not affected B Turns all heat off, micro not affected C Disables clean mode in both ovens, allows cook and microwave D Error will remain in display until repaired and powered up. No error tones E 1. Turn the clock selector knob to OFF 2. “Tweak” the oven control by turning the clock selector knob slightly to the left (counter clockwise). This may stop the flashing message/beeping and clear the display window. F Tweaking clears to "---" for retry G Clears when oven temp drops below runaway temp and selector is off H Can be cancelled by tweaking if a good oven temperature sensor is detected I Cleared with a mode change J Can be tweaked away for retry. User must unlatch and delete the "---" to try to relatch the door K Turns all heat and micro off L If two switches show locked door, then "E13" and "Lock" are permanent in display (all modes). If two switches show an open door you can tweak away the "E13" Back to TABLE OF CONTENTS THERMADOR Range/Stove/Oven Fault Codes starting with an F Error Code Notes Check/Repair F0 Internal logic failure; cancel key supervision. Sounds alarm and resets to non-cook mode Replace the electronic range control (also called clock or ERC) F1 Internal logic failure (monitoring function). Sounds alarm and inhibits cook modes Replace the electronic range control (also called clock or ERC) F2 Temperature runaway detected (Bake/Broil: 600 - 700 F; Clean: 930 1000 degrees F). Sounds alarm and resets to non-cook mode. Check relay board for stuck contacts. Check oven temperature sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check sensor wiring connectors for a loose or high resistance connection. Check electronic range control (also called clock or ERC) functions Replace relay board if necessary. Replace oven temperature sensor if other components check normal. If failure repeats, replace electronic range control (also called clock or ERC) F3 Open circuit detected; oven temperature sensor. Check sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check wires and connections between electronic range control (also called clock or ERC) and oven temperature sensor Replace sensor if other components check normal. Replace electronic range control (also called clock or ERC) if fail code reoccurs F4 Short circuit detected; oven temperature sensor. Check sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check wires between electronic range control (also called clock or ERC) and sensor. Replace sensor if other components check normal. Replace electronic range control (also called clock or ERC) if fail code reoccurs F7 Function key shorted for over 16 seconds. Check for something pressing a key or preventing normal release of the key Replace electronic range control (also called clock or ERC) if other components check normal F8 Internal logic failure; calibration. Alarm sounds and resets to non-cook mode. Check oven temperature sensor for normal room temperature resistance (1085-1097 ohms at 75 F). Check wires and connections between electronic range control (also called clock or ERC) and oven temperature sensor Replace electronic range control (also called clock or ERC) and oven temperature sensor if other components check normal F9 Internal logic failure; door latch supervision. Alarm sounds and resets to non-cook mode. If door is locked due to clean temperatures, disconnect power until door can be unlocked Replace the electronic range control (also called clock or ERC) Fd Bake & Broil relay drives active simultaneously. Check relay board for damage: trace E6 to K2 & K3, and burned contacts K3 & K4 Replace electronic range control (also called clock or ERC). Replace relay board if necessary Blank display No power to electronic range control (also called clock or ERC). Check oven If relay board transformer open (E1 to E2), replace relay board. light and cooktop dial lights (powered by L2 & L1, respectively). Check relay board transformer primary, E1 to E2 (140 ohms typical). If the transformer internal fuse is still OK, check output voltages, pins 9 - 8 (3.2 v.a.c.) and 7 - 6 (21 v.a.c.). Check clock functions after replacing relay board If still no clock functions replace electronic range control (also called clock or ERC) Back to TABLE OF CONTENTS WESTINGHOUSE Range/Stove/Oven Fault Codes Failure Code Condition Check/Repair F0 & F1 EOC (Electronic Oven Control) failure Replace EOC (Electronic Oven Control) F2 Oven too hot Likely a bad oven temperature sensorpossible bad EOC (Electronic Oven Control) F3 Oven temperature sensor open Replace oven temperature sensor F4 Oven temperature sensor shorted Replace oven temperature sensor F5 or F6 or F7 EOC (Electronic Oven Control) failure Replace EOC (Electronic Oven Control) Back to TABLE OF CONTENTS WHIRLPOOL Polara Failure Code Fault Priority Condition Check/Repair F1 F0 N/A EEPROM communication error Replace control F1 E1 N/A EEPROM checksum error Replace control F1 E2 7 UL A/D errors Replace control F1 E4 2 Model ID error Reinsert keytail. If not corrected, replace control. F1 E6 0 Latch signal mismatch error Replace control F2 E0 4 Shorted key error Replace keypad assembly F2 E1 3 Keytail unplugged Reinsertkeytail F3 E0 5 Top oven sensor open Check for open circuit. Sensor resistance should be 1K to 1.1K @ room temperature. If not, replace the sensor. F3 E1 6 Top oven shorted Check for shorted sensor circuit, otherwise replace sensor F3 E2 9 Bake range over temperature At room temperature, sensor resistance should be 1K to 1.1K. If not, replace the sensor. If the sensor checks okay, replace the control. F3 E3 8 Clean range over temperature At room temperature, sensor resistance should be 1K to 1.1K. If not, replace the sensor. If the sensor checks okay, replace the control. F3 E4 10 Bottom oven sensor open Check for open circuit. Sensor resistance should be 1K to 1.1K @ room temperature. If not, replace the sensor. F3 E5 15 Bottom oven sensor shorted Check for shorted sensor circuit, otherwise replace sensor F5 E0 14 Door switches do not agree Check door switch. Contacts should be closed when plunger is actuated. Check door switch circuit for open. F5 E1 16 Door latch not operating Check that door switch is completely closed. Check latch, solenoid, and actuation switch for electrical or mechanical malfunction. F8 E0 17 Refrigeration not operating properly Check for open circuit between control and refrigeration cooling module Power failure (not a failure mode) Do not replace control PF Back to TABLE OF CONTENTS WHIRLPOOL Range/Stove/Oven Fault Codes Non Y-Line NOTE: Not valid for Y line. If there is a Y near the end of your model number, do not use this chart. Failure Code Condition Check/Repair 4 Digit Failure Code F0 - E0 Analog to Digital Failure Disconnect for 30 seconds - if display re-appears - replace control F1 - E1 Safety flip flop Replace Electronic Range Control/Clock (ERC) F2 - E0 Shorted keypad Replace Electronic Range Control/Clock (ERC) F3 - E0 Oven temperature sensor or oven temperature sensor fuse opened Replace oven temperature sensor or fuse F3 - E1 Oven temperature sensor shorted Replace oven temperature sensor F3 - E2 Oven too hot Replace oven temperature sensor F3 - E3 Clean temp too hot Replace oven temperature sensor F5 - E0 F5 Check door/latch switch - E1 and E2 Replace component 2 Digit Failure Code F0 or F1 or F5 Failed transistor Replace Electronic Range Control/Clock (ERC) F2 - E0 Oven temp too high 1. Test operation of door lock on selfclean models 2. Test relay contact operation 3. High resistance in oven temperature sensor F3 Open oven temperature sensor or thermal fuse Replace oven temperature sensor or thermal fuse F4 Shorted oven temperature sensor Replace oven temperature sensor F6 Problem in time keeping circuit 1. Reset time and/or cooking operation 2. Check for proper ground F7 Stuck function switch or button Replace ERC (Electronic Range on Electronic Range Control (ERC) Control/Clock) F8 Failure Electronic Range Control (ERC) Replace ERC (Electronic Range Control/Clock) F9 Door lock circuit Check wiring and test operation of door lock switch Back to TABLE OF CONTENTS WHIRLPOOL Range/Stove Oven Fault Codes, Common Failure Code Condition Check/Repair Digit Failure Code 2 F1 Analog to Digital Failure Disconnect for 30 seconds - if display reappears - replace control board F1 Safety flip flop Replace board F1 Shorted keypad Replace keypad F3 Oven temperature sensor opened Replace oven temperature sensor F2 Oven temperature sensor shorted Replace oven temperature sensor F3 Oven too hot Replace oven temperature sensor F3 Clean temp too hot Replace oven temperature sensor F5 Check door/latch switch Replace switch if defective 4 Digit Failure Code F1 - E1 Safety flip flop Replace board F2 - E0 Shorted keypad Replace keypad F3 - E0 Oven temperature sensor opened Replace oven temperature sensor F3 - E1 Oven temperature sensor shorted Replace oven temperature sensor F3 - E2 Oven too hot Replace oven temperature sensor F3 - E3 Clean temp too hot Replace oven temperature sensor F5 - E0 F5 - E1 and E2 Check door/latch switch Replace switch if defective Back to TABLE OF CONTENTS WHIRLPOOL Range/Stove Oven 30" Free-standing, Models SF3…& 24" Built-In Failure Code Condition Check/Repair F2 Oven temperature above specifications 8-pin connector oven temperature sensor to the Electronic Range Control (ERC) F3 Open oven temperature sensor Check wiring harness, replace oven temperature sensor if necessary F4 Shorted oven temperature sensor Check wiring harness, replace oven temperature sensor if necessary F5 Pushbutton stuck Check for binding of pushbuttons and control panel glass. If OK, replace touch panel F6 Computer logic interrupted (timing) Replace Electronic Range Control (ERC) F7 Computer logic interrupted (lock motor) Replace Electronic Range Control (ERC) F8 Computer logic interrupted Replace Electronic Range Control (ERC) Back to TABLE OF CONTENTS WHIRLPOOL Duet & Duet HT Failure Code F/H Condition No water detected entering machine or Pressure switch trip not detected. If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed. Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the pressure switch trip, the valves will be turned off and the error code will flash. Check/Repair Press PAUSE/CANCEL twice to clear the display. If there is no water in the unit: 1. Make sure that both valves at the water source(s) are turned on all the way. 2. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves 3. Verify inlet valve operation If there is water in the unit: 1. Verify Drain pump operation 2. Pressure Switch Hose is in good condition and properly connected to Tub and Pressure switch Verify there is not a siphon problem Verify wire harness connections to:Inlet Valves, Pressure Switch, Drain Pump, Flow Meter, and Central Control Unit (CCU) Check all hoses for possible leaks Verify pressure switch operation Verify flow meter operation Verify CCU operati F/02 F/05 Long Drain Press PAUSE/CANCEL twice to clear the display. If the drain time exceeds 8 minutes, the water valves are turned off and "F/02" is flashed. Check the drain hose and make sure it is not plugged or kinked. NOTE: After 4 minutes the "Sud" error will be displayed, then 4 minutes later the F02 error code will be displayed. Check the drain pump filter for foreign objects. Check the electrical connections at the pump and make sure the pump is running. If the above does not correct the problem, replace the pump. Water Temperature Sensor Error Check the Water Temperature Sensor, Heating Element and Element Relay If during the water heating step in wash cycle, the water temperature sensor (NTC) value is out of range, or the heating element circuit has failed, the "F/05" error code will be displayed. Check connections to the Sensor, Heating Element and Relay F/06 Drive Motor Tachometer Error The control is unable to properly detect motor speed and the machine will shut down. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes. F/07 Motor Control Unit Error The Central Control Unit has detected a short in the motor control unit. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes. F/09 F/10 F/11 Check wire harness connections between the Drive Motor/Tachometer and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) Check the Drive Motor Check the MCU Check the Wire Harness Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) Check the MCU Check the Drive Motor Check the Wire Harness Overflow Condition Check the drain hose and make sure it is not plugged or inked. If the Overflow contact on the pressure switch is Closed for more than 60 seconds and Overflow condition will occur. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Unplug the unit to service. Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU) Motor Control Unit (MCU) Heat Sink Thermal Trip Check for Proper Installation, verify the unit is not located near a source of heat and has proper ventilation. If the thermal protector on the MCU heat sink gets too hot, it will open the thermal protector on the heat sink which will stop motor functions and an "F/10" will be displayed. Check Wire Harness connectors to the MCU, and Central Control Unit (CCU) Serial Communication Error Check Wire Harness connectors to the MCU, the motor, and Central Control Unit (CCU) Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. Check/Clean Drain Pump Filter of foreign objects Check for Drain Pump Failure Check the Inlet Valve for proper shut off Check the Pressure switch for proper operation Check the Drive system for any worn or failed components Check MCU Check Motor Check the Drive system for any worn or failed components Check MCU Check CCU Check Motor Check Wire Harness F/13 Dispenser Circuit Error If the dispenser motor is not able to be driven to it's proper position. Check mechanical linkage from dispenser motor to the top of the dispenser. Check Wire Harness connections to the dispenser motor and Central Control Unit (CCU) Check Dispenser Motor F/14 EEPROM Error The Central Control Unit (CCU) receives it's data from an EEPROM on board the CCU. If there is an error reading this data, it will cause this error. F/15 Sud A power glitch may cause this error. Try unplugging the Unit for two minutes to see if that fixes the error. Check CCU Motor Control Unit (MCU) Error Check Wire Harness connectors to the MCU, the motor, and Central Control Unit (CCU) If the MCU detects multiple resets or errors during a wash cycle, it will go into this error mode. Check Drive belt SUDS LOCK (Overdose of Detergent detected during the Wash Cycle) If too much detergent was used, run the unit through a Rinse/Spin cycle, then a Normal cycle, without adding any detergent. This should clear the unit of the excess detergent. The motor control unit senses a suds lock condition by analyzing the current draw on the drive motor. If "Sud" is displayed a potential suds lock is detected. This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds. Check MCU Check Motor Check Wire Harness Check the drain hose and make sure it is not plugged or kinked. Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU) Check/Clean Drain Pump Filter of foreign objects Check Drain Pump Check Pressure Switch Check CCU F/dL Door Lock Error Door Lock Mechanism broken or removed from the Door A Door Lock Error occurs if the door cannot be unlocked. It will try to lock it 6 times before displaying the error. Check Door Lock/Switch Assembly Check the wire harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU) Door Lock/Switch Assembly Failure F/dU Door Unlock Error A Door Unlock Error occurs if the door cannot be unlocked. It will try to unlock the door 6 times before displaying the error. Door Lock Mechanism broken. Check Door Lock/Switch Assembly for foreign objects Check Wire Harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU) Door Lock/Switch Assembly Failure Back to TABLE OF CONTENTS WHIRLPOOL Calypso Washing Machine Failure Code PF Condition Power Failure Check/Repair PF flashes if the washer loses power during a running cycle. The washer does not flash PF when it is first plugged in. Press START to continue the cycle from the moment that power was lost -ORPress STOP/CANCEL to clear the display and completely cancel the cycle. FL Flood Condition FL flashes if any overfill condition occurs. This condition occurs when excessive water in the tub causes the overfill switch to trip. The control must realize that the trip was due to an overfill condition instead of a suds lack condition in order for FL to be displayed With an overfill condition, the beeper repeats a warning every 10 seconds with no time-out. The pump is cycled in drain mode for 30 seconds on, 30 seconds off until the overfill switch resets or power is discontinued to the unit. Press STOP/CANCEL to clear the display. Er Processor Reset Error This error code is displayed if the control failed to save cycle information during a power failure. This does not generate an error code beep. Press STOP/CANCEL to clear the display. LF Long Fill CE Communications Error If the water fill time exceeds ten minutes, the water valves are turned off and LF is flashed. Press STOP/CANCEL to clear the display. If there is any breakdown in communication between the machine controller and the motor controller, CE flashes and the unit beeps once. Some common causes of CE errors include: · Conformal coating on serial communications pins between the machine controller and motor controller. After disconnecting power to the unit, try scraping this coating off the pins. · Check the resistance values between the serial communications pins with the connectors in place. Make sure the harness does not have a bad connection. · Check the quick disconnect at the motor terminal. The drive motor must be hooked up properly or a CE error will occur. · Drive motor thermal protector has opened. ·Motor controller is not powered or fuse has opened. Replace motor controller. Press STOP/CANCEL to clear the display. Ld Long Drain Ld flashes if it takes longer than 5 minutes to pump out water to a point where the operating pressure switch resets. Press STOP/CANCEL to clear the display. CA Cl Average current limit Or Instantaneous current limit If a status signal comes back from the motor controller that a current limit has been breached, the unit will return to standby mode and display either CA for average current limit trip or Cl for instantaneous current limit trip. Average current trip occurs if there is a 2 second average of current draw greater than 5.55 amps at the motor windings. Instantaneous current trip occurs if there is a spike of 26 amps instantly at the motor windings. This may signify problems with the drive motor, thermal protector, or motor controller. Over-loading the unit may cause this problem. Press STOP/CANCEL to clear the display ob Off Balance If the motor controller detects an unrecoverable offbalance condition, the machine controller will shut down and display an ob for Off Balance The lid switch must be opened at least once before restarting the cycle, if this condition occurs. Opening the lid will allow the customer to view and redistribute the load. Press STOP/CANCEL to clear the display. Sr Stuck Relay Sr signifies a failure of the relay in the closed position. With this failure, power to the motor controller cannot be turned off by the machine controller. The machine control board may have a bad relay and may need to be replaced. Check pins 1 and 5 of P16 of the machine controller and pins 1 and 2 of P1 of the motor controller. This should have AC line voltage when the motor controller is powered. Press STOP/CANCEL to clear the display. LS Lid Switch Error The control should flash this error code if it cannot detect the lid switch opening and closing properly. This error code may also be used if there is a disagreement between the motor and machine controllers on the stat if the lid switch. The control should not allow the unit to run in this condition. This code will also appear if the user presses the START key while the lid is open. Open the lid or press STOP/CANCEL to clear the display. Back to TABLE OF CONTENTS WHIRLPOOL Calypso Matching Dryer Failure Code Condition Check/Repair PF Power Failure If the household power goes off and the control board was in RUN mode or PAUSE mode, the electronic control board will display a power failure error code. E1 or E2 Thermistor Failure The dryer will not operate if the exhaust temperature drops below 18 degrees F. or exceeds 250 degrees F. When the thermistor circuit is open (>50K ohms), the error code E1 flashes in the display. When the thermistor circuit is shorted (<500 ohms), the error code E2 flashes in the display. Normal thermistor resistance values: 60 degrees F. - 15.3K ohms. 70 degrees F. - 11.9K ohms. 80 degrees F. - 9.2K ohms. E3 Touchpad or Software mismatch Flashes when there is a touchpad or software mismatch. NOTE: This error code is displayed only in diagnostics mode. Back to TABLE OF CONTENTS Home | Find Parts | Repair Help | Accessories | Customer Service | Your Account | Shopping Cart Top of Page Legal Notices and Disclaimers ©1999 - 2007 RepairClinic.com®, Inc. All rights reserved. (2)
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021