Revision 1.01
The owner/user MUST INSTALL a CARBON MONOXIDE
DETECTOR in the living area near to where the vehicle is being stored or parked. It is the sole responsibility of the owner/user to keep the remote transmitters away from the reach of children and handle with care so that the system does not unintentionally start. When the vehicle is parked in an enclosed
/partially enclosed area (ex: garage, car port...), being serviced
(ex: oil change) or if the vehicle is loaned to an operator not familiar with a remote starter, the system MUST BE placed in
Service (Valet) Mode.
MANUAL TRANSMISSION STARTERS the installation of a remote starter MUST only be done with a specified manual transmission starter. It is the sole responsibility of the vehicles owner to insure that the vehicle is left with the transmission in neutral position when the remote starter is in use. The manual transmission starter is designed to be an added measure of safety ONLY! The manufacturer does not guarantee or insure against any damages or loss of life that could result in the event of a remote starter starting while the vehicle is in gear.
Manual transmission models are designed only to act as a deterrent against the vehicle starting in gear, this is the vehicle’s owner’s and operator’s responsibility.
NEVER OPERATE THE SYSTEM IN AN ENCLOSED/ PARTIALLY
ENCLOSED AREA!
SERVICE (VALET) MODE
5 secs
Button Operations
REMOTE CONTROL T99 (5 BUTTONS)
Button Functions
Press 1 once
Press and hold 1 for 2 seconds
Arming and lock doors
Lock doors
Remote panic
Press 2 once
Press and hold 2 for 2 seconds
Press 3 once
Press and hold 3 for 2 seconds
Disarming & unlock doors
Unlock doors
Trunk release
Remote engine starter on
Idle mode on
Remote engine starter off
Idle mode off
Conditions
Alarm is disarmed
While driving
Anytime
Alarm is armed
While driving
Anytime
Anytime
ACC on and RPM on
Remote start
Idle mode
Press 4 once
Press and hold 4 for 2 seconds
Press 4 once then 1 in 3 seconds
Turbo mode on
Car finder/ trunk release
Press 4 once then 3 for 2 sec. follow by time Remote timer mode on/off
Press 5 once System status query
Anytime
Anytime
Set alarm and door lock for 15 seconds Disarm
Anytime/Timer start
Anytime
T99
1
3
5 s
2
4
T99 SETTING FUNCTION LIST
Button
Press 3 and 4 for 2 seconds
Press 5 once
Press 5 once
Press 5 once
Press 5 once
Press 5 once
Press 5 once
Press 5 once
Press 3 and 4 for 2 seconds
Function
Enter Program mode
Enter time of hour setting
Enter time of minute setting
Alarm clock ON/OFF
Enter alarm hour setting
Enter alarm minute setting
Setting backlight LED ON/OFF
Vibration motor ON/OFF
Exit Program mode
Setting
Anytime
Press button 1 for time increase
Press button 2 for time decrease
Press button 1 for time increase
Press button 2 for time decrease
Press button 1 for alarm on
Press button 2 for alarm off
Press button 1 for time increase
Press button 2 for time decrease
Press button 1 for time increase
Press button 2 for time decrease
Press button 1 for LED on
Press button 2 for LED off
Press button 1 for vibration on
Press button 2 for vibration off
Program mode
T99 SETTING FUNCTION
Anytime you press button 3 and button 4 for 2 seconds, the transmitter will enter program setting mode, then the
ICON of the time clock, alarm clock, horn and vibrate, or backlight LED will begin to flash. The first setting is hour setting; use button 1or button 2 to adjust the hour up or down. After setting the hour, press button 5 to shift to minute setting. The operation is the same as the hour setting. After you are done setting the clock, press button 5 to shift to alarm clock se tting.
If the alarm clock setting is ON, then the remote will go to alarm time setting. The procedure is the same as for time setting. After the alarm clock setting, pressing button 5 will enter the backlight LED setting; press button 1 to set the backlight LED function to ON (with any button press, the backlight will light 5 for seconds), press button 2 to set the backlight LED function to
OFF (backlight will not come on with any button press. After the backlight LED setting, pressing button 5 will enter the vibration setting, press button 1 to set vibration function to ON, press button 2 to set vibration function to OFF. The vibrate function only operates on ala rm or alarm/starter models when the alarm is set off in the vehicle or when the alarm clock function that is built-in to the remote is used.
After setting vibration mode, press button 5 again to exit p rogram mode. Pressing no buttons for 5 seconds will also exit program mode.
Alarm clock function:
If the seconds and vibrate for 10 seconds.
During the alarm period, any button push will shut off the alarm clock. After the alarm clock has been shut off, it will stay set for the same time the next day unless you go into programming and turn the alarm clock function off.
T99 LCD INSTRUCTIONS
TIME CLOCK
ICON
DOOR LOCK/UNLOCK
SENDING SIGNAL
SIGNAL SIGN
VALET MODE
SIREN
ALARM CLOCK
VIBRATION REMINDER
TRUNK RELEASED
STARTED
DOOR OPEN
KEY ON
CAR HOOD
PARKING LIGHT
ENGINE TURBO
STARTING
TIMER START
SHIFT
BATT ERY
Explanation
Indicates that your car is locked or unlocked
Indicates horn is honking when locking or unlocking your vehicle
Indicate that your remote-pager is sending signals to the controller unit
Indicates alarm clock mode is on
Display time
Indicates that parking lights are flashing
Indicates that your trunk is open
Indicates that your hood is open
Indicates that your door is open
Indicates if you are in valet mode
Indicates that vibration mode is on
Indicates that your vehicle has actually started and is running
Indicates the key on status
Displays remaining battery life
Indicates the turbo mode is on
Indicates function transfer and setting mode
Indicates your vehicle is in remote-start mode
Indicates timer start mode is on
LOCK
A. Press LOCK button momentarily.
B. Parking lights will flash 1 time, horn will honk 1 time*, doors will lock.
C. The LED on the antenna will begin to flash slowly.
D. If the optional starter-disable circuit has been installed, it will activate as well.
UNLOCK
A. Press UNLOCK button momentarily.
B. Parking lights will flash 2 times, horn will honk 2 times*, doors will unlock.
C. The LED on the antenna will stop flashing. (If passive starter-disable is programmed, the LED will flash quickly for 60 seconds then rearm automatically.)
D. If the optional starter-disable is installed, it will be deactivated to allow the vehicle to be started by key.
SILENT LOCK/UNLOCK
A. Press both LOCK and UNLOCK buttons simultaneously.
B. Parking lights will flash once or twice to indicate doors locking or unlocking.
C. Any programmed horn confirmations are temporarily bypassed.
REMOTE START
A. With the engine off, press the START button.
B. The parking lights will flash and the horn will chirp once*.
C. The vehicle’s ignition system will come on and within 3 seconds, the vehicle will start. (If vehicle does not start, see the diagnostics section for possible solutions.)
D. The parking lights will flash 5 times to confirm a successful start.
E. The vehicle will run for the programmed runtime (15 minute default). To change your remote starter runtime, contact your dealer.
F. The vehicle can be remotely shutdown by pressing and holding the START button for 3 seconds.
TRUNK RELEASE --OPTIONAL--
The vehicle must be equipped with a power trunk release switch or a power sliding door to use this option.
A. Press and hold the UNLOCK button.
B. The doors will unlock and after 3 seconds, the trunk release will activate.
C. The trunk release can also be programmed to work independently on the CAR
FINDER button. If programmed, press and hold the CAR FINDER button for 3 seconds to activate trunk release.
2nd VEHICLE OPERATION
Your transmitter is capable of controlling a second TS141/TS151 system installed on another vehicle. (Requires some special programming, see your dealer for details.)
Switching control from one vehicle to the other is simple: indicator comes on solid.
B. Within 3 seconds, press any button to activate the corresponding feature for your second vehicle.
C. The transmitter automatically defaults back to your primary vehicle after any command to the 2nd vehicle or if no command is issued within 5 seconds.
PANIC MODE
To use Panic mode, the vehicle’s horn must be connected to your remote starter.
A. Press the LOCK button for 3 seconds.
B. The horn will sound and the parking lights will flash for 60 seconds.
C. Pressing the LOCK or UNLOCK buttons will cancel Panic mode.
CAR FINDER
To use Car Finder mode, the vehicle’s horn must be connected to your remote starter.
A. Press and hold the CAR FINDER button for 3 seconds.
B. The parking lights will flash and the horn will chirp 5 times.
NOTE: Car Finder option is not available when the trunk release option has been programmed to work on this button
IDLE MODE (CONTINUOUS RUN)
This option allows you to remove your key and leave the engine running up to the programmed runtime
A. With the engine running, press the START button.
B. The Horn will chirp twice* and the remote starter will come on.
C. Remove the ignition key and the vehicle will stay running for the length of the programmed runtime (15 min. default)
D. The vehicle can be shutdown anytime by holding down the START button for 3 seconds or by depressing the brake pedal.
TURBO MODE
This option allows for a cool down on turbo equipped vehicles.
A. With the engine running, press the CAR FINDER button. (Brake pedal must not be depressed)
B. The parking lights will flash and the horn will chirp 2 times*.
C. Remove the ignition key and the engine will continue to run for approximately 2 minutes.
VALET MODE
This mode disables remote starting and bypasses the starter-disable circuit (if installed).
A. Turn the vehicle ignition key to the on position (you do not need to start the vehicle).
B. Press and hold the button on the windshield antenna.
C. After about 5 seconds, the parking lights will flash once and you will hear 5 chips from the vehicle’s horn*.
D. Turn the ignition key to the OFF position. The LED on the antenna will come on solid.
E. The system should now be in VALET mode.
F. To cancel VALET mode, repeat steps A and B. After 5 seconds, you will see 2 parking light flashes and the horn will chirp 2 times*.
G. The system should now be out of VALET mode.
TIMER START MODE
This option allows you start your vehicle automatically at preset intervals over a 24-hour
time period.
A. Press and release the CAR FINDER button, then press and hold the START button for about 3 seconds until the timer indicator on the transmitter comes on; the parking lights on the vehicle turn on as well.
B. Within 5 seconds, select your start interval by pressing one of the 3 buttons on the transmitter. (See table). If you do not select an interval, timer will not be set.
C. Once you have selected your start interval, the park lights will flash the hour setting you have chosen. The transmitter will display the setting as well.
D. The vehicle will start every (your selection) hours for a period of 24 hours.
E. To cancel timer start mode, repeat step 1. The parking lights will flash and the horn will chirp 2 times.* The timer indicator on the transmitter will flash.
NOTE: Starting the vehicle by key or by remote will automatically cancel timer start mode.
Button
LOCK (button 1)
UNLOCK (button 2)
START (button 3)
1 Flash H 01 Vehicle with start every hour
2 Flashes H 02 Vehicle will start every 2 hours
3 Flashes H 03 Vehicle will start every 3 hours
TRANSMITTER LEARNING
Important! The remote starter will hold 4 transmitter codes. It is recommended that when programming in transmitters, you fill up all four transmitter codes, even if only using one or two transmitters. This will clear all other transmitter coding from the unit and prevent stray coding or possible interference from other remote transmitters.
STEP 1 - Within 3 seconds turn the ignition key to the “ON”
position three times leaving “ON” the third time.
STEP 2 - Press and hold the Program Button. The park
lights will turn “ON” and the horn (optional) will
honk once. Continue to hold the Program
Button, the park lights will turn “OFF” and the
horn (optional) will honk 5 times quickly.
5 secs
NOTE: If the parking lights do not turn “ON”, release the Program Button and
turn the ignition to the “OFF” position, wait 5 sec and repeat steps 1 & 2.
STEP 3 - While holding the Program Button, press and
release the button on each of the remote
transmitters to be programmed. If using two
transmitters, code in each transmitter twice.
Diagnostics
If the remote starter does not activate when the button is pressed, the park lights will flash a diagnostic code to indicate what shutdown input has been triggered.
Flashes Problem
3 slow flashes System is in valet mode
4 slow flashes Door Open
5 slow flashes Ignition ON
5 flashes
6 flashes
7 flashes
Brakeswitch
Hoodswitch
Tach lock-out
Solution
Cancel Valet Mode
Manual trans. models only
Turn off Ignition key and try again
Contact your product dealer
Contact your product dealer
Start vehicle with key, after 5 sec. try again
BATTERY REPLACEMENT
When your starter system begins to show a significant reduction in transmitter range, or the remote does not respond correctly, it may be time to change the battery. The transmitter uses 1- 1.5 Volt AAA (Triple A) battery.
If the transmitter shows no significant improvement after replacing the batteries, contact your product dealer to have the system inspected.
The manufacturer warrants to the original purchaser of the remote starter and/or alarm, that the product shall be free from defects in material and workmanship. However, should this product be proven to be defective, within a three year period from the original date of purchase, the manufacturer will, without charge to the purchaser
(excluding any charges incurred to have the product delivered to the manufacturer), repair or replace any part of the remote starter and/or alarm which the manufacturer agrees to be defective. After the initial three year period the manufacturer shall repair or replace defective products with a nominal processing fee of $35.00
USD. All warranties apply to the original purchaser and the vehicle in which the unit was originally installed
ONLY. Repairs or replacement of defective modules shall remain at the discretion of the manufacturer. All other parts, components, accessories, and/or optional equipment pertaining to the remote starter and/or alarm are not included in the manufacturer's warranty. This warranty is non-transferable. Request for warranty service from any Factory Authorized Dealer must be accompanied with the original purchase receipt. Failure to comply with any of these conditions may result in warranty being voided. This warranty does not cover the following: removal and reinstall labor charges, shipping charges, abuse, misuse, or accidental damages to the remote starter and/or alarm, automobile, and/or parts thereof. This warranty is void upon modification, repairs, or alterations to any part of the product. The manufacturer does not guarantee or insure against theft of the vehicle or its contents. Alarm models are designed only to act as a deterrent against possible theft. This alarm may qualify for auto insurance discounts. Contact your insurance agent for further information. The manufacturer shall not be held liable for any consequential damages due to breach of this or any other warranty, expressed or implied. This warranty gives you specific legal rights. Your specific legal rights may vary for each region.
CERTAIN DAMAGES EXCLUDED – The manufacturer expressly disclaims any liability or responsibility for incidental damages caused by the product, including economic loss, loss of use of the product, car rentals, or any other costs relating to the care and custody of the product. The manufacturer disclaims liability or responsibility for any consequential damages caused by the product or resulting from its use, including the cost of repairing or replacing other property damaged by the product or caused by its use, whether or not the product is working properly. The product is intended to deter unauthorized use of the vehicles in which it is installed.
The manufacturer does not warrant that the product is fool-safe against theft and/or vandalism and/or human error or misuse. The manufacturer accepts no liability or responsibility for any damage of any kind whatsoever caused to any vehicle in which the product is installed or any resulting damage from its use. The manufacturer accepts no responsibility or liability for any damage resulting to or theft of the vehicle or its contents caused or alleged to be caused, directly or indirectly, by failure of the product.
MANUAL TRANSMISSION STARTERS – The installation of a remote starter in a manual transmission vehicle MUST only be done with a specified manual transmission starter. The manual transmission starter is designed to be an added measure of safety ONLY! The manufacturer does not guarantee or insure against any damages or loss of life that could result in the event of a remote starter starting while the vehicle is in gear. Manual transmission models are designed only to act as a deterrent against the vehicle starting in gear. It is the sole
This device complies with Part 15 of the FCC rules. Operation of this device is subject to the following conditions:
(1)
(2)
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.
(3) CAUTION: Changes or modifications not expressly approved by the part responsible for
Notes:
FCC/ID Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance void the user’s authority to operate this devise.
