8 device home theater
In TV, VCR, DVD, SAT, and CBL modes, use
FAV to scan favorite channels and/or all
channels. See Using Channel Scan and
Programming Favorite Channel Scan.
8 DEVICE HOME THEATER
Use CH+ (or CH-) to select the next higher
(or lower) channel.
UNIVERSAL REMOTE CONTROL
Press PREV once to recall the last-viewed
channel and to page back one screen on
the main menu.
SU
RROU
ND SOU
ND
5. Aim the remote control at the device and press POWER once. The
device should turn off. If it does not respond, repeat steps 2
through 5, trying each code for your brand until you find one that
works. If it still does not work, try Searching For Your Code.
NOTE: If the device does not have a POWER key, press the
(Play) key.
6. Repeat steps 1 through 5 for each device you want to control.
For future reference, write down each working device code in the
boxes below:
SAT Code:
CBL Code:
In the RCVR/AMP mode, use the keypad
(1 ~ 9 and 0) to select audio sources 1
through 10.
RCVR/AMP Code:
The One For All 8 Device Home Theater Universal Remote Control is
designed to operate up to eight home entertainment devices, including TV, video, and audio components. The remote control requires
two (2) new AA alkaline batteries (not included) and easy programming to control your devices. For best results, please read and perform all instructions listed here.Also, keep these instructions for
future reference.
About Control Groups
For Home Theater programming, the remote control’s keys are
grouped by type of control into the following five control groups:
AUX Code:
(1) Transport Controls:
PLAY, STOP, FWD, REW, PAUSE, and REC
Aux. Device Type: _______________________________
(2) Volume Controls:
VOL+, VOL-, and MUTE
Use the Key Charts (below) to learn how to use the universal features
and functions of the One For All 8 Device Home Theater Universal
Remote Control.
Press TV, VCR, DVD, AUX, SAT, CBL,
RCVR/AMP, or CD once to select a desired
home entertainment device to control.
After programming, press HOME THEATER
once to select the home theater mode (see
Using The Home Theater Mode).
Press POWER once to turn on or off the
selected device.
Press MENU once to display your selected
device’s main menu.
Use GUIDE to display your selected
device’s program guide or setup menu.
Use EXIT to exit from your selected
device’s guide or menu.
Use INFO to display the current channel
and program information.
ND SOU
ND
Use the cursor keys to move the cursor in
the program guide and menu screens.
Use SELECT to choose options from your
selected device’s menu or guide.
▲
In the CD mode, use SELECT to select a
compact disc. Use ▲ (or ▼) to select the
next (or previous) CD. Use (or ) to
select the next (or previous) track.
▲
RROU
▲
In the RCVR/AMP mode, use SELECT to
set the surround sound. Use ▲ (or ▼)
to adjust the volume higher (or lower).
Use (or ) to adjust the balance left
(or right).
▲
SU
Use VOL+ (or VOL-) to raise (or lower) the
sound volume.
1. On the remote control’s back, push the tab and lift off the
battery cover.
2. Obtain two (2) new AAA alkaline batteries. Match the + and –
marks on the batteries to the + and – marks in the battery case,
then insert the new batteries.
3. Press the battery cover back into place. The tab should click
when the cover is locked.
4. Test the remote control by first pressing POWER and then any
mode key (e.g., TV). If batteries are inserted correctly, the LED
(red light) will blink once.
NOTE: When batteries need replacement, the remote control will stop
operating. Remove the old batteries and insert new ones within 30 minutes
to ensure all of your programming information is restored.
PROGRAMMING DEVICE CONTROL
The One For All 8 Device Home Theater Universal Remote Control is
preprogrammed at the factory to operate an RCA TV and VCR, a
Motorola (GI) cable box, an RCA satellite receiver, a Pioneer CD player, a Toshiba DVD player, a Pioneer audio receiver/ amplifier, and a
One For All home automation device. To control devices other than
the default brands, perform the following steps; otherwise skip this
section:
NOTE: For TV/VCR Combo control, see the next section.
1. Turn on a device (e.g.,VCR or DVD player) and, if applicable,
insert media (e.g., cassette or disc).
NOTE: Please read steps 2 through 4 completely before proceeding.
Highlight or write down the codes and device you wish to program before
starting step 2.
2. On the remote control, press a device key once (i.e., TV, VCR, DVD,
AUX, SAT, CBL, RCVR/AMP, or CD).
NOTE: Use the AUX key to program control of home automation devices or
miscellaneous audio services and video accessories. Alternately, use the AUX
key to program control of a second device type (e.g., a second VCR; see “Reassigning Device Keys”).
3. Press and hold SET until the LED (red light) blinks twice, then
release SET.
Press MUTE once to turn the sound off
or on.
4. Use the Manufacturer’s Codes (on the back) to locate the type of
device and brand name and then enter the first four-digit code
for your device. If performed correctly, the LED will blink twice.
NOTE: If the LED did not blink twice, repeat steps 2 through 4 and try
entering the same code again.
CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST,
SLEEP, INFO, and TV/VCR
(4) Menu Controls:
MENU, GUIDE, Cursor Controls (Up, Down,
Left, Right), SELECT, and EXIT
NOTE: If the LED did not blink twice, repeat steps 2 through 4 and try
entering the same code again.
5. Aim the remote control at the device and press POWER once. It
should turn off. If the device does not respond, repeat steps 2
through 5, trying each code for your brand until you find one that
works. If it still does not work, try Searching For Your Code.
NOTE: If the device does not have a POWER key, press the
(Play) key.
6. If you’ve located a setup code that works, but it has a separate TV
code, you’ll also need to program it into the remote control to
access volume control as follows:
b. Enter the TV code for your TV/VCR Combo. If correct, the
LED will blink twice.
NOTE: For VCR/TV Combos programmed with separate TV codes,
TV volume is controlled by pressing VCR first and then TV. After that, use
VOL+ (or VOL-) to raise (or lower) the TV volume. For other alternatives on
controlling your volume keys, see the “Changing Volume Lock” or “Using
Keymover” sections.
7. For future reference, write down the working TV/VCR combo
code in the below boxes:
TV/VCR Code:
TV Code (if used):
SEARCHING FOR YOUR CODE
If your device does not respond to the remote control after trying all
codes listed for your brand, or if your brand is not listed at all, try
searching for your code.
For example, to search for a code for your TV:
1. On the remote control, press TV once.
2. Press and hold SET until the LED (red light) blinks twice, then
release SET.
3. Enter 9 - 9 - 1. The LED will blink twice.
4. Aim the remote control at the the TV and slowly alternate
between pressing POWER and TV. Stop when the TV turns off.
NOTE: In the search mode, the remote control will send IR codes from its
library to the selected device, starting with the most popular code first.
5. To lock in the code, press and hold SET until the LED blinks
twice, then release SET.
6. To search for the codes of your other devices, repeat steps 1
through 5, but substitute the appropriate device key for the
device you are searching for.
(2) Device Group 2:
TV, VCR, CBL, SAT, CD, and RCVR/AMP
(3) Device Group 3:
TV, VCR, CBL, SAT, CD, and RCVR/AMP
(4) Device Group 4:
TV, VCR, CBL, SAT, and DVD
(5) Device Group 5:
TV
The default Device Group setting from the factory is:
1. After performing Global Volume Lock (above), press and hold
SET again until the LED (red light) blinks twice, then release SET.
1. Press and hold SET until the LED (red light) blinks twice, then
release SET.
2. Enter 9 - 9 - 5. The LED will blink twice.
3. Press MACRO once.
4. Press TV once.
5. Enter the channel number, 7 - 1.
NOTE: If you have access to over 100 channels, enter 0 -7 -1. Moreover,
if the original remote control required pressing an Enter key to change
the channel, also press the Enter key after the channel number (e.g.,
0 -7 -1-Enter).
NOTE: The following keys cannot be used as a source or destination: TV, VCR,
DVD, AUX, SAT, HOME THEATER, CD, CBL, RCVR/AMP, and SET.
Programming Keymover
For example, if your VCR does not have volume control, you can
map the volume and mute keys from the TV mode to the VCR mode
as follows:
1. Press and hold SET until the LED (red light) blinks twice, then
release SET.
2. Enter 9 - 9 - 4. The LED will blink twice.
3. For the source mode, press TV once.
NOTE: This example assumes all equipment is turned off and that the TV is
connected through the cable box with TV tuning set to channel 3.
8. Repeat steps 1 through 7 twice more, substituting VOL– and
MUTE as source and destination keys in steps 4 and 6.
Upon completion of the above procedure, you can now use your
One For All 8 Device Home Theater Universal Remote Control to
control the TV’s volume and mute in the VCR mode, as well as in the
TV mode.
Restoring Keymoved Keys to Default Settings
(2) Device Group 2:
TV
1. Press and hold SET until the LED (red light) blinks twice, then
release SET.
(3) Device Group 3:
CBL
2. Enter 9 - 9 - 5. The LED will blink twice.
1. Press a device key that has a keymoved key.
(4) Device Group 4:
CBL
3. Press MACRO once.
(5) Device Group 5:
TV
4. Enter the following sequence:
2. Press and hold SET until the LED (red light) blinks twice, then
release SET.
Programming The Home Theater Mode
TV, POWER, and 0 - 3 (or 0 -0 - 3 if access is over 100 channels)
For example, let’s assume you have a TV, a cable box, and a VCR in
your home theater system.You can set up the Home Theater mode
so that selected controls are assigned to these devices as follows:
NOTE: If the original remote control required pressing an Enter key to
change the channel, also press the Enter key after the channel number (e.g.,
0 -7 -1-Enter).
5. Then enter the following sequence:
CBL, POWER, and 1-1 (or 0 -1- 1 if access is over 100 channels)
2. Press and hold SET until the LED (red light) blinks twice, then
release SET.
6. Press and hold SET until the LED blinks twice, then release SET.
3. Enter 9 - 7 - 9. The LED will blink twice.
Now when you press MACRO once, the TV will turn on and tune to
channel 03. Then the cable box will turn on and tune to channel 11.
4. Select a device. For this example, press VCR once. Then assign a
desired Control Group to the device. For this example, press PLAY
once, which will assign the entire group of Transport Controls
(i.e., PLAY, STOP, FWD, REW, PAUSE, and REC) to the VCR. The LED
will blink once.
5. Select another device. For this example, press TV once. Then
assign a desired Control Group to this device. For this example,
press VOL+ once, which will assign the entire group of Volume
Controls (i.e., VOL+, VOL-, and MUTE) to the TV. The LED will
blink once.
6. Select another device. For this example, press CBL once. Then
assign a desired Control Group to this device. For this example,
press CH+ once, which will assign the entire group of Channel
Controls (i.e., CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST, SLEEP,
INFO, and TV/VCR) to the Cable Box. The LED will blink once.
7. To add additional Menu functionality to the Cable Box, press CBL
once. Then press MENU once. This action will assign the entire
group of Menu Controls (i.e., MENU, GUIDE, Cursor Controls (Up,
Down, Left, Right), SELECT, and EXIT) to the Cable Box. The LED
will blink once.
8. To add PIP functionality to the TV, press TV once. Then press PIP
once. This action will assign the entire group of PIP Controls (i.e.,
PIP, MOVE, and SWAP) to the TV. The LED will blink once.
9. To exit Home Theater programming, press and hold SET until the
LED (red light) blinks twice, then release SET.
Operating The Home Theater Mode
After programming the Home Theater key (see the previous section),
you simply activate this mode by pressing HOME THEATER once.
Instantly, groups of remote control keys will be assigned to their
programmed devices.
CHECKING THE CODES
VCR:
PLAY, STOP, FWD, REW, PAUSE, and REC
If you have set up the remote control using the Searching For Your
Code procedure, you may need to find out which four-digit code is
operating your equipment. For example, to find out which code is
operating your TV:
TV:
VOL+, VOL-, MUTE, PIP, MOVE, and SWAP
Cable Box:
CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST,
SLEEP, INFO, TV/VCR, MENU, GUIDE,
Cursor Controls (Up, Down, Left, Right),
SELECT, and EXIT
2. Press and hold SET until the LED (red light) blinks twice, then
release SET.
A macro can be programmed to turn on and off your equipment as
well. For example, let’s set up a sequence that will turn on the TV
and tune it to channel 3, and then turn on the Cable Box and tune it
to a premium channel (e.g., 11).
7. The LED will blink twice indicating the keymoved sequence
is correct.
VCR
For the above example, pressing HOME THEATER once would assign
the following keys to the VCR, TV, and Cable Box:
1. On the remote control, press TV once.
Example – Programming A Master Power Key With Instant
Channel Selection
4. For the source key, press VOL+ once.
(1) Device Group 1:
1. On the remote control, press HOME THEATER.
3. Now, when you press VOL+, VOL–, or MUTE, the volume of the
selected device (e.g., TV) will be controlled regardless of the
mode you have selected.
The One For All 8 Device Home Theater Universal Remote Control
includes a Keymover feature that allows you to map (or copy) keys
from one mode (i.e., source mode) to another mode (i.e., destination
mode).
6. For the destination key, press VOL + once.
VCR, DVD, CD, and RCVR/AMP
2. Enter 9 - 9 - 3 and then press any mode key once (e.g., TV). The
LED will blink twice.
For example, let’s assume your favorite cable programs are on
channel 71. Use the following instructions to program a macro for
direct access of this channel:
Now when you press MACRO, you will instantly see cable channel 71
on your TV set.
(1) Device Group 1:
1. Press and hold SET until the LED (red light) blinks twice, then
release SET.
Unlocking Volume Control For A Single Device (Individual
Volume Unlock):
Moreover, the remote control’s devices are grouped into the following
five device groups:
NOTE: Please read steps 2 through 4 completely before proceeding.
Highlight or write down the codes and device you wish to program before
starting step 2.
PIP, MOVE, and SWAP
Locking Volume Control To One Mode (Global Volume Lock):
USING KEYMOVER
5. For the destination mode, press VCR once.
4. Use the Setup Codes For TV/VCR Combos (on the back) to locate
the brand name and then enter the first four-digit code for your
device. If performed correctly, the LED will blink twice.
INSTALLING BATTERIES
(3) Channel Controls:
device. However, you may change the Volume Lock setting to Global
Volume Lock so that a device’s volume will be locked to one mode
(e.g., to control TV volume in all other modes).After that, if desired,
you can perform Individual Volume Unlock on a selected device to
set its volume control for independent operation.
With so many channels available through your cable or satellite
system provider, you can program a macro that directly selects a
favorite channel with one key press.
6. Press and hold SET until the LED blinks twice, then release SET.
a. Press TV once. The LED (red light) will blink twice.
The LED (red light) blinks to show that
the remote control is working and is
sending signals.
6. To exit programming, press and hold SET for 3 seconds. The LED
will blink twice.
About Device Groups
Use MOVE to move the window picture
to different positions in the main picture.
Key Charts
NOTE: If you try entering more than 10 channels, the remote control will
automatically exit programming.
1. Turn on the TV/VCR Combo and insert a video cassette.
3. Press and hold SET until the LED (red light) blinks twice, then
release SET.
Use SET for all programming sequences.
5. If desired, repeat step 4 (in this section) for each favorite channel
to be stored, up to a total of 10 channels.
(5) PIP Controls:
Use PIP to switch the Picture-In-Picture
feature on or off (if available on your TV).
Press SLEEP to activate your device’s sleep
timer (not available for all devices).
NOTE: Programming a new macro over an existing one will erase the
original macro.
NOTE: If the original remote control required pressing an Enter key to
change the channel, also press the Enter key after the channel number (e.g.,
0 -3-1-Enter).
Perform the following instructions to control a TV/VCR Combo:
2. On the remote control, press VCR.
Use to turn on or off the key backlight.
When this feature is activated, keys will
remain backlight for 5 seconds after the
last key press.
FEATURES AND FUNCTIONS
PROGRAMMING TV/VCR COMBO CONTROL
After programming, press MACRO once to
run a desired macro (see Using A Macro).
Use SWAP to switch images and sound
between the main and window pictures.
A macro can be used to control a home theater operation, to set a
favorite channel, or for other multiple functions you would like to
control with one key press (see examples below). Moreover, the
MACRO key can hold up to 15 key presses total.
NOTE: This example assumes the TV tuner is connected directly to the cable
line and not through a cable box.
Control Organization
Use TV/VID to switch the TV’s input to
view TV or video programs.
INTRODUCTION
5. Repeat step 4 three more times for remaining digits. Use 2 for the
second digit, 3 for the third digit, and 4 for the fourth digit.
The One For All 8 Device Home Theater Universal Remote Control
includes a custom Home Theater mode. After the HOME THEATER
key is programmed, it will allow you to access five groups of
remote control keys without having to change device modes.
CD Code:
USER’S GUIDE
NOTE: If a code digit is “0”, the LED will not blink.
USING THE HOME THEATER MODE
Use the keypad (1 ~ 9 and 0) to directly
select channels (for example, 009 or 031).
To record a VCR program, press REC twice.
With programming, the MACRO key on your One For All 8 Device
Home Theater Universal Remote Control can be setup to
perform a repetitive, time-consuming operation for easy, convenient
access through the press of a single key.
4. Use the keypad to enter a favorite channel number (e.g., 031).
Then press SET once.
Example – Programming A Favorite Channel
In the RCVR/AMP mode, use PREV to select
the receiver band.
Use the transport keys to control your
VCR, DVD or CD player, or VOD (Video
On Demand) if available on your cable or
satellite service.
4. To view the code for the first digit, press 1 once.Wait 3 seconds,
count the LED blinks (e.g., three blinks = 3) and write down
the number.
VCR Code:
DVD Code:
In the CD mode, use ENTER to add 10 to
the digit entry (e.g., ENTER and 7 is 17).
USING A MACRO
6. To check for codes of other devices, repeat steps 1 through 5,
but substitute the appropriate device key for each device you
are checking.
TV Code:
In the CD mode, use PREV to turn random
play on or off.
Press ENTER once after entering the
channel numbers on some TVs.
3. Enter 9 - 9 - 0. The LED will blink twice.
Clearing A Macro
1. Press and hold SET until the LED (red light) blinks twice, then
release SET.
2. Enter 9 - 9 - 5. The LED will blink twice.
3. Press MACRO once.
4. Press and hold SET until the LED blinks twice, then release SET.
USING CHANNEL SCAN
In the TV, VCR, DVD, SAT, and CBL modes, use the FAV key to start a
3-second scan of all favorite channels (if programmed – see
Programming Favorite Channel Scan below) and/or all channels for
the selected mode.
1. If Favorite Channel Scan has been set up, skip to step 2.
Otherwise, press TV, VCR, DVD, SAT, or CBL once.
2. Press FAV once.
• If Favorite Channel Scan has been set up, scanning of favorite
channels will start and, upon completion, continue to scan all
channels upward for the same device.
• If Favorite Channel Scan has not been set up, scanning will
start with the current channel, then proceed to the next
channel up, and continue until all channels of the selected
device is scanned.
Restoring A Single Keymoved Key
3. Enter 9 - 9 - 4. The LED will blink twice.
4. Press the destination key twice (where the keymoved key is
stored). The LED will blink twice.
Restoring All Keymoved Keys In A Single Mode
1. Press and hold SET until the LED (red light) blinks twice, then
release SET.
2. Enter 9 - 9 - 4. The LED will blink twice.
3. Press the destination mode twice (where keymoved keys are
stored). The LED will blink twice.
RE-ASSIGNING DEVICE KEYS
The One For All 8 Device Home Theater Universal Remote Control
can be set to control a second TV,VCR, DVD player, or
other device.
3. Enter 9 - 9 - 3 and then press VOL– once. The LED will blink
four times.
4. If desired, repeat steps 1 through 3 (of this section) for each
device that you want volume to be unlocked.
5. Now, after you select a device that has volume unlocked (e.g.,
RCVR/AMP), pressing VOL+, VOL–, or MUTE, will control the
device’s volume only in its own mode.
Unlocking All Volume Control (Restoring Default Setting):
NOTE: Performing these instructions will restore independent volume control
for all programmed devices (e.g., TV volume control in TV mode, VCR volume
in VCR mode, etc.).
1. On the remote control, press and hold SET until the LED (red
light) blinks twice, then release SET.
ABOUT UPGRADING
The One For All 8 Device Home Theater Universal Remote Control
has the largest infrared code library available. However, if you purchase a brand new home entertainment or home automation
device, it may not respond to the codes stored in the remote control’s memory.
If this happens, please contact our Customer Support department
(see Customer Support below) to upgrade the remote control. The
Customer Support representative will search our entire database for
a code that matches your device and instruct you how to enter it
into your One For All 8 Device Home Theater Universal Remote
Control.
If the code for your home entertainment or home automation device
is not in our database,we will need to “capture” the code for that
device from its original remote control. A new code would then be
created and entered into your One For All 8 Device Home Theater
Universal Remote Control.If necessary,the Customer Support representative can instruct you how to begin the capture procedure.
NOTE: One For All reserves the right to replace a returned remote control with
a new one of equal or superior functionality.
Upgrade Exclusions
• Home entertainment or home automation devices controlled by
radio frequency (RF/UHF), wired, or ultrasonic remote controls.
Only devices controlled by infrared remote controls are covered.
• Home entertainment or home automation devices not controlled
by remote controls.
2. Enter 9 - 9 - 2. The LED will blink twice.
• All products for sale and/or use outside the continental United
States, Hawaii,Alaska, or Canada.
• Products that operate over 100 kHz.
AUX as 2nd TV key:
SET - 9 - 9 - 2 - TV - AUX
AUX as 2nd DVD key:
SET - 9 - 9 - 2 -DVD- AUX
AUX as 2nd SAT key:
SET - 9 - 9 - 2 -SAT- AUX
AUX as 2nd CD key:
SET - 9 - 9 - 2 -CD- AUX
AUX as 2nd CBL key:
SET - 9 - 9 - 2 -CBL- AUX
AUX as 2nd RCVR/AMP key:
SET - 9 - 9 - 2 - RCVR/AMP - AUX
PROGRAMMING FAVORITE CHANNEL SCAN
In the TV, VCR, DVD, SAT, or CBL mode, you can store a list of up to
10 favorite channels, in any order, that will be immediately scanned
when FAV is pressed (see Using Channel Scan).
When a re-assignment is done, the LED (red light) will blink twice to
confirm your choice.At that time, you will need to program the
remote control for the new device (see Programming Device Control).
2. Press and hold SET until the LED (red light) blinks twice, then
release SET.
CHANGING VOLUME LOCK
3. Enter 9 - 9 - 6. The LED will blink twice.
The One For All 8 Device Home Theater Universal Remote Control is
set at the factory for independent volume control of each selected
PROBLEM:
Tried Search For Your Code method and still could not
find a working code.
SOLUTION: Clear the device key as follows: Press and hold
SET until the LED (red light) blinks twice, then
release. Next enter 9 - 9 - 2. Then press the device key
to be cleared twice. Now repeat the Search For Your
Code method.
PROBLEM:
Remote control does not turn on Sony or Sharp
TV/VCR Combo.
SOLUTION: For power on, these products require programming
TV codes. For Sony, use TV code 0000 and VCR
code 0032. For Sharp, use TV code 0093 and VCR
code 0048.
PROBLEM:
CH+ and CH- do not work for your RCA TV.
SOLUTION: Due to RCA design (1983-1987), only the original
remote control will operate these functions.
PROBLEM:
No remote control of volume.
SOLUTION: See Changing Volume Lock to lock/unlock volume.
CUSTOMER SUPPORT
• E-mail: [email protected]
• Consumer Help Line: (330) 405-8615
LIMITED WARRANTY
One For All® warrants, to the original purchaser only, that this product will be free from defects in materials and workmanship, under
normal use, for ninety (90) days from the date of original purchase.
This limited warranty is valid only on ONE FOR ALL® product purchased and used in the United States of America or Canada, and
does not apply to products used for industrial or commercial purpose.
The limited warranty does not cover damage or failure caused by
products or services not supplied by ONE FOR ALL® , or which
result from accident, misuse, abuse, neglect, mishandling, misapplication, faulty installation, set-up adjustment, improper maintenance,
alteration, maladjustment of consumer controls, modifications, commercial use, or that is attributable to acts of God.
There are no express warranties except as listed above. ONE FOR
ALL® SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS
PRODUCT OR ARISING OUT OF ANY BREACH OF WARRANTY.
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE,ARE LIMITED TO THE WARRANTY
PERIOD SET FORTH ABOVE. Some states do not allow the exclusion
or limitation of incidental or consequential damages, or limitations
on how long an implied warranty lasts, so the above exclusions or
limitations may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which vary from
state to state.
To obtain warranty service for a defective product during the warranty period, please return the product, preferably in the original
carton, along with your purchase receipt, to the store of original purchase.A note detailing the complaint would be helpful. The store, at
its option, will replace or repair this product if found to be defective.
One For All
(330) 405-8655
ADDITIONAL INFORMATION
TROUBLESHOOTING
One For All Access 3 ..............................................................URC-3605
PROBLEM:
One For All Video Expert 4 Device .......................................URC-4081
If you own a satellite that uses code 0775 (Express Vu
and Echostar) and your exit key does not work, perform the following sequence to activate this
feature/function.
SOLUTION: 1. Press the CBL/SAT key
2. Press and hold the SET key until the red LED blinks
twice
3. Press 9-9-4, the red LED will blink twice
4. Press SET and release (one blink on LED)
5. Press 3-3-6
6. Press the EXIT key, the red LED will blink twice.
The Exit key will now correctly perform the exit feature/function on your satellite.
PROBLEM:
LED (red light) does not blink when you press a key.
SOLUTION: Replace batteries with two new AA alkaline batteries.
PROBLEM:
NOTE: Only channels of one mode can be stored for Favorite Channel Scan.
1. On the remote control, press TV, VCR, DVD, SAT, or CBL once.
SOLUTION: If original remote control required pressing ENTER
to change channels, press ENTER on the remote
control after entering the channel number.
As you update your home entertainment system, One For All® has
a universal remote control that will fit your needs. Look for these
exciting products at a retailer near you.
4. The AUX key is now ready to be programmed for your second
VCR. See Programming Device Control.
Perform Sequence
Changing channels does not work properly.
• Internet: http://www.oneforall.com
• Infrared keyboards and infrared pointing devices (such as
mouse substitutes).
To Re-Assign Device Key
PROBLEM:
3. Volume will again be independently controlled according to its
default states for all programmed devices.
1. On the remote control, press and hold SET until the LED (red
light) blinks twice, then release SET.
To re-assign other device keys to the AUX key, repeat steps 1 through 4
above by substituting the sequence from the below chart:
TV/VCR combo does not respond properly.
SOLUTION: Use the VCR codes for your brand. Some combo
units may require both a TV code and a VCR code
for full operation.
For assistance, please contact us in any of the following ways:
• Broken or defective product.
3. Press VCR once, then press AUX once.
PROBLEM:
2. Enter 9 - 9 - 3 and then press VOL+ once. The LED will blink
four times.
For example, to control a TV, a cable box, and two VCRs, you will
need to re-assign the unused AUX key to operate the second VCR
as follows:
You can also re-sassign another unused device key by substituting an
open key for the AUX key in the above chart and performing the
sequence. For example, to re-assign an unused SAT key as a 2nd CD
key, perform SET - 9 - 9 - 2 -CD- SAT.
3. To stop scanning channels at any time, press any key once
(except the backlight key ).
2. Press a desired mode key where you want volume to be unlocked
(e.g., RCVR/AMP) and controlled within its own mode.
SOLUTION: Try all listed codes for the device brands being
set up. Make sure they can be operated with an
infrared remote control.
LED blinks when you press a key, but home
entertainment device does not respond.
SOLUTION: Make sure the remote control is aimed at your
home entertainment device and is not farther
than 15 feet away.
PROBLEM:
The unit does not control home entertainment devices
or commands are not working properly.
One For All Video Expert Plus 4L .........................................URC-4880
One For All Access 4 ..............................................................URC-4605
One For All Access 5 ..............................................................URC-5705
One For All 6 Device Home Theater .....................................URC-6011
One For All 8 Device Home Theater .....................................URC-8011
One For All 8L Device Home Theater
with Learning Capability.......................................................URC-8811
One For All A/V LCD 8 Device With Learning .....................URC-8910
One For All IR/RF LCD 8 Device With Learning..................URC-9910
ONE FOR ALL® is the registered trademark of Universal Electronics
Inc. Computime International Ltd. is the Licensee of the ONE FOR
ALL® brand for USA and Canada.
Copyright 2002 by Universal Electronics Inc.No part of this publication
may be reproduced,transmitted,transcribed,stored in any retrieval
system,or translated to any language,in any form or by any means,
electronic,mechanical,magnetic,optical,manual,or otherwise,without the prior written permission of Universal Electronics Inc.
The One For All® 8 Device Universal Remote Control is
compatibile for use in North America, excluding Mexico.
URC-8011
02/02
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement