ICandy Peach, Blossom, Blossom Twin stroller Instruction manual

iCandy

Peach

InstructIon manual

ImPortant: Read these instructions carefully before use and keep for future reference. Your child’s safety may be affected if you do not follow these instructions.

WarnIng: It may be dangerous to leave your child unattended.

Peach Inst AUS Print V4.indd 1 21/07/2011 20:24

iCandy

Peach

Welcome to the world of

icandy

Please take time to read this instruction booklet carefully as correct use and maintenance of your iCandy stroller is essential.

If you have any problems or queries, please contact your local stockist or read the FAQ’s at

www.icandyworld.com/au

When unpacking your stroller, please make sure that all plastic packaging is kept away from babies and young children and please ensure your child is kept clear of all moving parts during assembly.

2

iCandy

Peach

Peach Inst AUS Print V4.indd 2 21/07/2011 20:24

iCandy

Peach

iCandy Peach

Peach Inst AUS Print V4.indd 3

iCandy Peach

3

21/07/2011 20:24

iCandy

Peach

icandy peach instructions

Contents

Section 1 – Chassis

Section 2 – Seat Unit

Section 3 – Bassinettes

Section 4 – Peach “Blossom”

Section 5 – Peach “Blossom Twin”

Section 6 – Single Stroller Car Seat Adaptors

Section 7 – Blossom Stroller Car Seat Adaptors

Section 8 – iCandy Peach Configurations

Section 9 – Accessories

Section 10 – General Use & iCare

Section 11 – Important Safety Information

Safety First

Correct use and maintenance of your stroller is essential. Please take the time to fully and carefully read this instruction manual.

If you require any further advice or assistance when using your stroller, please contact the place of purchase.

WarnIng With the exception of the outer packaging carton, to prevent injury from choking or suffocation hazards, remove and immediately discard all other protective packaging on this product.

The iCandy Peach is tested to comply with AS/NZS 2088:2000,

AS/NZS 2088:2009. Consumer Protection Notice Nº. 8 of 2007.

ImPortant: this stroller has been modified specifically for the australian market and includes a red brake operator, tether strap and a straight bumper bar which may differ from images shown. the operation of any modified parts is not affected.

note: seat liners shown are available as an accessory.

Useful tip

New products are sometimes stiff to engage and operate. We recommend ALL adaptors (sold separately) and connector parts be lightly lubricated with a silicone based furniture polish. This is best achieved by spraying polish onto a soft cloth and applying to relevant parts.

4

iCandy

Peach

Peach Inst AUS Print V4.indd 4 21/07/2011 20:24

Section 1 – Chassis

1

Contents:

Chassis inc. front wheels & basket

Rear Wheel x 2, Axles x 2

Seat Unit, canopy, bumper bar

PVC Raincover

1 - to fit rear wheels to chassis:

Depress axle button to engage as shown. Check security of wheels by pulling outwards.

2 - to open the chassis: Release the hold together clip (store clip

in-line with handle chassis).

2

3 - Allow front frame of chassis to move forwards.

4 - Lift up handle until locks engage.

WarnIng Ensure that all the locking devices are engaged before use

3

4 iCandy

Peach

Peach Inst AUS Print V4.indd 5 iCandy

Peach 5

21/07/2011 20:24

iCandy

Peach

5

5 - Brakes: Press down on pedal to engage. Lift up to release.

6 - Front wheels: Can be selected in fixed or swivel position. (Swivel position

required for folding chassis).

7 - Handle height adjustment:

Adjust handle height to desired position (x4) by depressing button and pulling up.

to fold chassis: (Remove seat/

bassinette before folding):

Unload all products from the basket.

8 - Apply brakes. Depress handle button and slide handle fully down in a swift/smooth action to disengage hub locks.

6

7

8

6

iCandy

Peach

Peach Inst AUS Print V4.indd 6 21/07/2011 20:24

iCandy

Peach

9

9 - As the hub locks release; move/rotate handle down.

10 - Pull up basket frame at centre using carry strap or hinge joint, allowing the front frame and wheels to move inwards.

10

11 - Secure folded chassis using hold together clip (Please note:

the chassis will only fully close & stand upright if the front wheels are selected to swivel & the

handle is at its lowest height).

The folded chassis can be carried using the carry strap. (Check

security of strap clips, before

lifting).

11

12 - tether strap: The iCandy

Peach is fitted with a tether strap which should always remain fitted to the chassis and should be positioned to either side of the handle height adjustment button.

12

Should you need to remove & refit the strap for example after cleaning, simply pass the larger looped end through the small loop and pull to secure.

Peach Inst AUS Print V4.indd 7

iCandy Peach

7

21/07/2011 20:24

iCandy

Peach

Section 2 – Seat Unit

Important: The seat frame movement mechanism is supplied in the store/transport position.

1 - to operate: Depress and hold both the outer frame release ring and the centre recline button simultaneously before rotating leg to centre position as shown.

Action on both sides of frame before fitting to the chassis.

Important: Failure to do this will lead to damage to your seat unit.

2 - removal of hood:

Removing the hood requires the use of the hood removal/ operation key.

3 - Depress both locking tabs and allow connectors to lift out of sockets.

1

2

3

8

iCandy

Peach

Peach Inst AUS Print V4.indd 8 21/07/2011 20:24

4

4 - Insert the hood removal / operation key into the zip puller.

5

5 - Rotate the key into an upright position.

6 - Pull upwards to disengage the zip fully and around the seat.

6

7 - attaching the hood: Engage the end of the zip into the foot of the zip. Insert the hood removal/ operation key into the zip puller.

8 - Rotate the key into an upright position and pull upwards and around the seat to fit the zip fully.

Important: Remove key.

Important: Always engage the zip so it is fully closed and remove key.

7

8 iCandy

Peach

Peach Inst AUS Print V4.indd 9

iCandy Peach

9

21/07/2011 20:24

iCandy

Peach

9

note: For Australian market the shape of the bumper bar will differ slightly. Operation and fitting is not affected.

9 - Bumper bar: Attach the

Bumper Bar with the inclined angle towards the foot end of seat unit. Ensure both locking tabs fully engage. Check security by pulling bar upwards.

10

10 - removal of bumper bar:

Depress both locking tabs firmly inwards and lift from sockets.

11 - attaching seat unit: Insert the seat unit into the main connectors on the chassis. Push down on each side of the seat frame to engage.

11

12 - Check that both locking tabs are flush with the chassis hub slots before use. The Seat Unit can be positioned to face you or face forwards.

12

WarnIng Check that the bassinette or seat unit attachment devices are correctly engaged before use.

10

iCandy

Peach

Peach Inst AUS Print V4.indd 10 21/07/2011 20:24

13 - to recline the seat unit:

Depress the centre grey buttons simultaneously and rotate seat to desired position (3 recline

positions in single mode).

14 - to remove the seat unit:

(Remove child before). Depress the lower portion of the grey outer ring on each side of the seat and lift the seat unit upwards.

14

15 - Footrest: Depress both hinge buttons and move footrest to desired position. Release button to lock.

15

13 iCandy

Peach

Peach Inst AUS Print V4.indd 11

iCandy Peach

11

21/07/2011 20:24

iCandy

Peach securing your child using the

5 point safety harness: Push the left and right connectors into the buckle housing & click together. Adjust the length of the straps using slider buckles “a”.

Raincovers

Fitting of raincovers: Fit raincover over the hood/ canopy area before fitting over the footrest part of the frame.

Ensure elasticated seams of raincover are positioned over frame of Seat Unit.

to release connectors:

Squeeze in and pull out of the buckle housing.

Fabric loops are provided for attaching an extra harness complying to BS 6684/EN13210.

WarnIng: Never leave raincovers, hoods and aprons on or over the stroller indoors, in a hot atmosphere or near a heat source, your child may overheat.

WarnIng: To avoid serious injury, always use the 5-point safety harness.

note: Shoulder straps are height adjustable.

The shoulder straps can be removed from the seat fabric by feeding through the back/ baseboards.

Important: A harness which can form loops may cause a strangulation hazard. When the seat is not in use the harness straps should always be disconnected.

12

iCandy

Peach

Peach Inst AUS Print V4.indd 12 21/07/2011 20:24

iCandy

Peach

Section 3 – Bassinettes

(all bassinettes)

Important: The bassinette attachment mechanism is supplied in the store/transport position.

1 - to operate: Depress and hold both the outer frame release ring and the centre recline button simultaneously before rotating leg to centre position as shown.

Action on both sides of the frame before fitting to the chassis.

1

Peach Inst AUS Print V4.indd 13

iCandy Peach

13

21/07/2011 20:24

iCandy

Peach

2

to erect bassinette: Remove apron and mattress.

2 - Position and secure both

‘stay’ bars into baseboard clips.

Replace mattress and apron as necessary.

3

3 - Hood/canopy: Clip hood frame into sockets ensuring both locking tabs are fully engaged.

Attach rear section of hood fabric using zip. Pull up the hood frame hoop to desired position.

To release hood, separate zip and depress both locking tabs before removing from sockets.

4 - Handle: Important: Attach the handle into the sockets with the inclined angle towards the HEaD EnD of the bassinette.

4

14

iCandy

Peach

Peach Inst AUS Print V4.indd 14 21/07/2011 20:24

5

5 - Ensure both locking tabs fully engage. Check security by pulling handle upwards.

6 - removal of handle: Depress both locking tabs firmly inwards and remove from sockets.

7 - Fitting the main Peach bassinette (rearward facing

only): Orientate the bassinette so that it is facing rearwards and insert the arms into the left & right receptors of the main hubs on the chassis.

6

Push down firmly on each side of the bassinettes frame to engage.

Check that the hub locking tabs are flush with the chassis hub slots before use.

7 iCandy

Peach

Peach Inst AUS Print V4.indd 15

iCandy Peach

15

21/07/2011 20:24

iCandy

Peach

8 - removal of main Peach

bassinette: Depress the lower portion of the grey outer ring on each side of the bassinette and lift.

Important: Do not lift bassinette using hood frame.

8

Bassinette Raincovers

Fitting of raincovers: Fit raincover over the hood/canopy area before fitting over the foot end of bassinette. Ensure elasticated seams of raincover are positioned under the base of the bassinette.

Bassinette Information

(Main)

main Bassinette

Internal measurements l x W: 74cm x 30cm

(Guide only for main bassinette mattress size)

External base measurements l x W: 75cm x 32cm

iCare

Bassinette liners and aprons are washable at 30 degrees.

Bassinette frames are sponge clean only.

16

iCandy

Peach

Peach Inst AUS Print V4.indd 16 21/07/2011 20:24

a

Section 4 – Peach

“Blossom”

Contents

Box 1:

As main pushchair

(See Section 1).

b

Box 2:

Blossom converter frames (b).

Main/upper seat stop screws

(not shown).

Lower seat unit (c).

PVC rain cover (not shown).

1 - Blossom Double/twin

chassis assembly & operation:

See section 1 of these instructions.

c

iCandy

Peach

Peach Inst AUS Print V4.indd 17

iCandy Peach

17

21/07/2011 20:24

iCandy

Peach

2

Blossom Converter

2 - attaching the Blossom

converter frames x2: Insert the top sections of each converter frame into the chassis hub connectors.

3 - Align the “saddles” on the lower parts of the frame with the basket frame.

Push down firmly on the top and bottom sections of the converter frames to engage

4 - Ensure locking tabs are flush with chassis hub slots and the

“Saddles” on the lower part of the frames are clamped around the basket frame.

5 - to release & remove the

Blossom converter frames:

Push across grey latching levers and disengage lower saddles before lifting the converter frame out of the chassis hubs.

Important: Remove both converter frames before attempting to fold the chassis

3

4

5

18

iCandy

Peach

Peach Inst AUS Print V4.indd 18 21/07/2011 20:24

iCandy

Peach

6

Lower seat unit

Important: The seat frame movement mechanism is supplied in the transport/storage position.

6 - to operate: Depress and hold both the outer frame release ring and the central release button simultaneously before rotating the leg to the central position

Action on both sides of the seat before fitting to chassis.

Important: Failure to do this will result in damage to your seat.

7

7 - attaching lower seat unit:

Insert seat arms into lower

“Blossom” converter frame sockets and push down firmly to engage.

note: Frame legs are grooved to prevent incorrect orientation

(forward facing only).

8 - to recline the seat unit:

Depress the central grey buttons simultaneously and rotate into the desired position.

9 - to release and remove seat

unit: Remove the child. Depress the lower portion of the grey outer rings of the seat unit, the frame will “Jump up”. The rings can be depressed simultaneously or independently.

8

9

Peach Inst AUS Print V4.indd 19

iCandy Peach

19

21/07/2011 20:24

iCandy

Peach

Upper/Main seat unit

Assembly & operation is the same as the single stroller (see Section

2).

Important: Ensure that the seat frame movement mechanism is taken out of the store/transport position prior to fitting (see page

8).

10 - seat stop screws x2:

Important: Fit the screws supplied to the upper/main seat unit movement mechanism this is essential to restrict upper seat recline movement to prevent interference with lower seat.

When assembled in “Blossom” tandem mode the main/upper seat unit is not suitable from birth.

10

11

11 - attaching upper seat

unit: Insert seat arms into upper

“Blossom” converter frame sockets and push down firmly to engage.

12 - reclining the seat unit:

Depress the central grey buttons and rotate into the desired position.

Important: Recline is restricted to

2 position to prevent interference between upper and lower seats.

13 - releasing & removing

upper seat unit: Remove child first. Depress lower portion of the grey outer ring on each side of seat unit, the frame will “Jump up”. The rings can be depressed simultaneously or independently.

12

13

20

iCandy

Peach

Peach Inst AUS Print V4.indd 20 21/07/2011 20:24

iCandy

Peach

Section 5 – Peach

“Blossom” Twin

a

Contents

Box 1: Stroller, (including seat

unit bumper bar & raincover, not

shown).

Box 2:

Blossom converter bars, lower seat unit & raincover (not shown).

b

Box 3:

Upper/lower Peach

Blossom twin bassinette (b).

Box 4:

Upper/lower Peach

Blossom twin bassinette (b).

Details of assembling all bassinettes including

Blossom Twin Bassinettes can be found in Section 3 of this manual.

1

1 - Fitting the lower Peach

Blossom bassinette (forward

facing only): Orientate the bassinette so that it is facing forwards and insert the arms into the left & right sides of the lower receptors of the Blossom converter bars. Press down firmly to engage.

Peach Inst AUS Print V4.indd 21

iCandy Peach

21

21/07/2011 20:24

iCandy

Peach

2 - Fitting the upper Peach

Blossom bassinette (rearward

facing only): Orientate the bassinette so that it is facing rearwards and insert the arms into the left & right sides of the upper receptors of the Blossom converter bars. Press down firmly to engage.

Important: Always ensure your bassinettes are securely fitted before use.

2

3 - removal of upper & lower

Peach Blossom bassinettes:

Important: The upper bassinette must be removed first.

Depress the lower section of the large light grey outer ring on each side of the bassinette and lift.

These buttons can be depressed simultaneously or independently.

Important: Do not lift the bassinette using the hood frame.

3

Bassinette Raincovers

Fitting of raincovers: Fit raincover over the hood/canopy area before fitting over the foot end of bassinette. Ensure elasticated seams of raincover are positioned beneath the bassinette.

Bassinette Information

Peach Blossom Bassinette

Internal measurements l x W: 69cm x 26.5cm

(Guide only for mattress size)

External base measurements l x W: 70cm x 27cm

iCare

Bassinette liners and aprons are washable at 30 degrees.

Bassinette frames are sponge clean only.

22

iCandy

Peach

Peach Inst AUS Print V4.indd 22 21/07/2011 20:24

iCandy

Peach

Bassinette information

WarnIng: The iCandy peach bassinettes are only suitable for a child who cannot sit up unaided, roll over and cannot push itself up on its hands and knees. Maximum weight of the child : 9 kg

(approx. 6 months).

WarnIng: Do not let other children play unattended near the bassinette.

WarnIng: Do not use if any part is broken, torn or missing.

Important:

1. Use only on a firm, horizontal, level and dry surface.

2. The handle and the bottom of the bassinette should be inspected regularly for signs of damage and wear.

3. Be aware of the risk of open fire and other sources of strong heat, such as electric bar fires, gas fires etc, in the vicinity of the bassinette.

4. The iCandy peach bassinette is not a safe means of transport by car and should NEVER be used as such. Use an approved car safety seat for transport by car.

Peach Inst AUS Print V4.indd 23

iCandy Peach

23

21/07/2011 20:24

iCandy

Peach

Section 6 – Single Stroller Car Seat Adaptors

1

Safe & Sound Unity infant car seat adaptor

(sold separately to fit the Safe

& Sound Unity infant carrier car

seat)

1- Fitting the adaptors:

Orientate the car seat adaptor with the curved bar to the rear of the chassis. Insert adaptor bracket into the main hubs of the chassis and press down firmly to engage.

2 - Fitting the safe & sound unity car seat (rearward

facing only): Position the car seat over the adaptor bracket so that the 2 vertical latch points are in line with the 2 rectangular apertures in the car seat base and the rear bar of the adaptor is in line with the light grey hook at the rear of the car seat.

2

24

iCandy

Peach

Peach Inst AUS Print V4.indd 24 21/07/2011 20:24

3

3 - Press down firmly to ensure both vertical latches and rear hook latch are fully engaged. Once fitted, lift the car seat upwards to ensure it is correctly fitted.

4 - removing the safe

& sound unity car seat:

Squeeze the light grey handle on the back of the car seat upwards to disengage the locking devices and lift off the adaptor bracket.

5 - removing the adaptor

bracket: Depress the bottom section of the large grey outer ring at each side of the adaptor bracket and lift off the stroller.

Important: Always ensure your car seat and adaptors are securely fitted before use.

4

5 iCandy

Peach

Peach Inst AUS Print V4.indd 25

iCandy Peach

25

21/07/2011 20:24

iCandy

Peach

1

Maxi Cosi Mico car seat adaptor

(sold separately to fit

the Maxi Cosi Mico carrier car

seat)

1- Fitting the adaptors:

(Marked L & R) Orientate and insert into the left and right sides of the chassis hub.

Press down firmly to engage.

2 - Fitting the maxi cosi mico car seat (rearward facing

only): Ensure adaptors are aligned with the fixing slots on the car seat.

2

26

iCandy

Peach

Peach Inst AUS Print V4.indd 26 21/07/2011 20:24

3 - Press down firmly to ensure the car seat is firmly locked onto the adaptors. Once fitted, lift the car seat upwards to ensure it is correctly fitted.

4 - removing the maxi cosi

mico car seat: Depress grey buttons on each side of the car seat simultaneously and lift off.

5 - removing of adaptors:

Depress large black button and pull out of chassis hub.

Important: Always ensure your car seat and adaptors are securely fitted before use.

4

5

3 iCandy

Peach

Peach Inst AUS Print V4.indd 27

iCandy Peach

27

21/07/2011 20:24

iCandy

Peach

Section 7 – Blossom Stroller Car Seat Adaptors

Peach Blossom & Safe

& Sound Unity infant car seat adaptor

(sold separately

to fit the Safe & Sound Unity

infant carrier car seat)

1

1- Fitting the lower adaptors:

Orientate the car seat bracket with the curved bar to the rear of the chassis. Insert adaptor bracket into the lower receptors of the Blossom converter bars and press down firmly to engage.

2

2 - Fitting the lower safe

& sound unity car seat

(rearward facing only):

Position the car seat over the adaptor bracket so that the 2 vertical latch points are in line with the 2 rectangular apertures in the car seat base and the rear bar of the adaptor is in line with the light grey hook at the rear of the car seat.

View from underside of car seat.

28

iCandy

Peach

Peach Inst AUS Print V4.indd 28 21/07/2011 20:24

iCandy

Peach

3

3 - Press down firmly to ensure both vertical latches and rear hook latch are fully engaged.

Once fitted, lift the car seat upwards to ensure it is correctly fitted.

4 - alternate fitting of the lower

safe & sound unity car seat:

Invert the car seat and place the adaptor bracket so the 2 latch points are in line with the rectangular apertures in the seat frame and the rear bar of the adaptor is in line with the light grey hook at the rear of the car seat.

4

5

5 - Push down firmly on the adaptor bracket until it locks onto the car seat base.

6 - Orientate the lower car seat to face rearwards and insert the adaptor arms into the lower receptors of the Blossom converter bars. Press down firmly to engage.

6

Important: Always ensure your car seat and adaptors are securely fitted before use.

Peach Inst AUS Print V4.indd 29

iCandy Peach

29

21/07/2011 20:24

iCandy

Peach

7

7 - to remove the adaptor:

Depress bottom section of the large grey outer ring on each side of the adaptor bracket and lift off.

8 - Fitting the upper adaptor:

Orientate the car seat bracket with the curved bar to the front of the chassis. Insert adaptor bracket into the upper receptors of the Blossom converter bars and press down firmly to engage.

8

9 - Fitting the upper safe & sound unity car seat (forward

facing only): Position the car seat over the adaptor brackets so that the 2 vertical latch points are in line with the 2 rectangular apertures in the car seat base and the rear bar of the adaptor is in line with the light grey hooks at the rear of the car seat.

9

10 - Press down firmly to ensure both vertical latches and rear hook latch are fully engaged.

Once fitted, lift the car seat upwards to ensure it is correctly fitted.

10

Important: Always ensure your car seat and adaptors are securely fitted before use.

30

iCandy

Peach

Peach Inst AUS Print V4.indd 30 21/07/2011 20:24

12

11 & 12 - removal of the safe

& sound unity car seats (upper

car seat must be removed

first): Squeeze the light grey handle on the back of the car seat upwards to disengage the locking devices and lift the car seat off the frame.

Repeat for lower seat.

13

13 & 14 - removal of adaptor

brackets: Depress the bottom sections of the large grey outer ring at each side of the adaptor bracket and lift off the chassis.

14

11 iCandy

Peach

Peach Inst AUS Print V4.indd 31

iCandy Peach

31

21/07/2011 20:24

iCandy

Peach

Upper adaptors

1

Peach Blossom & Maxi

Cosi Mico car seat adaptor

(sold separately to fit

the Maxi Cosi Mico infant carrier

car seats)

1 & 2 - Fitting the adaptors

(marked left & right): Orientate and insert the upper and lower sets of car seat adaptors into the left & right sides of the

Blossom converter bars. Press them down firmly until they engage.

3 - Fitting the lower maxi cosi mico car seat (rearward

facing only): Ensure lower adaptors are aligned with the fixing slots on the car seat.

Press firmly down to engage.

Once fitted, lift the car seat upwards to ensure it is correctly fitted.

2

3

Lower adaptors

32

iCandy

Peach

Peach Inst AUS Print V4.indd 32 21/07/2011 20:25

4

4 - Fitting the upper maxi cosi

mico car seat: Ensure upper adaptors are aligned with the fixing slots on the car seat. Press firmly down to engage.

Once fitted, lift the car seat upwards to ensure it is correctly fitted.

5

5 - removal of maxi cosi car

seats: Depress grey buttons on each side of the car seat simultaneously and lift off the adaptors.

6 - removal of upper adaptors:

Depress large black buttons on adaptors and lift upwards.

6

7 - removal of lower adaptors:

Push the light grey buttons outwards to release and lift upwards.

Important: Always ensure your car seat and adaptors are securely fitted before use.

7 iCandy

Peach

Peach Inst AUS Print V4.indd 33

iCandy Peach

33

21/07/2011 20:25

iCandy

Peach

1

Section 8 – iCandy Peach

Configurations

Single Stroller Options

2

“Which mode am I in today?”

The iCandy Peach is a versatile multi- functional design which enables you to adapt your stroller to your family’s requirements.

single stroller options:

(newborn – 3yrs)

1. Chassis with main seat unit.

(Forward or rearward facing)

3

2. Chassis with main bassinette.

(Rearward facing only)

3. Chassis with Safe & Sound

Unity Infant Car Seat.

(Rearward facing only)

4. Chassis with Maxi Cosi Mico

Infant Car Seat.

(Rearward facing only)

4

34

iCandy

Peach

Peach Inst AUS Print V4.indd 34 21/07/2011 20:25

1

Double “Blossom” Stroller

Options

Important! Your stroller can only be used in the configurations shown.

1. Chassis with main seat unit & lower Blossom seat unit.

(Forward facing only)

2

2. Chassis with Blossom bassinette & main seat unit.

(Forward facing only)

3. Chassis with main seat unit and Safe & Sound Unity

Infant Car Seat. (Seat unit

forward facing, car seat

rearward facing)

3

4. Chassis with main seat unit &

Maxi Cosi Mico Infant

Car Seat. (Seat unit facing

forwards, car seat rearward

facing)

4 iCandy

Peach

Peach Inst AUS Print V4.indd 35

iCandy Peach

35

21/07/2011 20:25

iCandy

Peach

5

Double “Blossom” Stroller

Options - continued

Important! Your stroller can only be used in the configurations shown.

5. Chassis with lower “Blossom” seat unit & upper Safe &

Sound Unity car seat.

(Seat and car seat forward

facing only)

6

6. Chassis with lower “Blossom” seat unit & upper Maxi Cosi

Mico car seat.

(Seat unit forward facing, car

seat rearward facing only)

7

Please note: When used with the lower “Blossom” seat unit and infant car seat as shown, the

“Blossom” seat should not be used in it’s most upright position.

7. Chassis with “Blossom Twin” bassinettes.

(Upper bassinette rearward

facing - Lower bassinette

forward facing)

8

8. Chassis with lower “Blossom” bassinette & upper Safe &

Sound Unity car seat.

(Both forward facing)

36

iCandy

Peach

Peach Inst AUS Print V4.indd 36 21/07/2011 20:25

9

Double “Blossom” Stroller

Options - continued

Important! Your stroller can only be used in the configurations shown.

9. Chassis with lower “Blossom” bassinette & upper Maxi Cosi

Mico car seat.

(Bassinette forward facing -

upper Maxi Cosi Mico car

seat rearward facing)

10

10. Chassis with 2 Safe & Sound

Unity car seats.

(Head to head fitting only)

11

11. Chassis with 2 Maxi Cosi

Mico car seats.

(Rearward facing only) iCandy

Peach

Peach Inst AUS Print V4.indd 37

iCandy Peach

37

21/07/2011 20:25

iCandy

Peach

1

Section 9 – Accessories

Accessories available for the iCandy Peach:

1. Maxi Cosi Mico car seat adaptors.

(Upper / Single)

2. Lower Maxi Cosi Mico car seat.

(Colour coded yellow)

3. Safe & Sound Unity car seat adaptor.

4. Superfleece Luxury Footmuff.

5. Main seat liner.

2

3

4 5

38

iCandy

Peach

Peach Inst AUS Print V4.indd 38 21/07/2011 20:25

6

6. Lower “Blossom” seat liner.

7. Parasol.

8. Large Changing Bag.

9. Cup Holder.

10. Clamp for Parasol & Cup holder.

11. Travel Bag (not shown).

7

8 iCandy

Peach

9 10

Peach Inst AUS Print V4.indd 39

iCandy Peach

39

21/07/2011 20:25

iCandy

Peach

Section 10 – General Use

• Your iCandy Peach stroller requires regular inspection and maintenance.

• Regularly inspect the locking devices, brakes, harness assembly, catches, seat adjusters, joints and fixings to ensure they are secure and in full working order.

• The brakes and wheels are subject to wear and should be replaced as and when necessary.

• Should any part of your iCandy Peach Stroller become stiff or difficult to operate, ensure that dirt is not the cause. Then try a light application of a sprayable lubricant e.g. Silicone spray, ensuring that the lubricant penetrates between the components, but take care as excessive application may encourage the accumulation of dirt. Regular light lubrication of moving parts will extend the life of your stroller and make opening and folding easier.

• Do not leave the iCandy Peach Stroller in sunlight for prolonged periods as the colour of some fabrics may fade.

• Store the stroller in a dry, well ventilated and safe place.

• Your stroller should be serviced and reconditioned before using it for a second baby, or within 18 months, whichever is the sooner. This can be arranged by contacting your iCandy dealer.

iCare

• Your iCandy seat unit fabric and safety harness can be cleaned by sponging lightly with warm water and a mild detergent. The safety harness is removable for additional cleaning.

40

iCandy

Peach

Peach Inst AUS Print V4.indd 40 21/07/2011 20:25

iCandy

Peach

• Your iCandy Peach removable seat liner(s) and bassinette liner(s) can be machine washed at 30 degrees. Please allow the product to dry naturally, do not bleach, tumble dry, iron or dry clean.

• iCandy soft accessories such as the foot muff and bassinette aprons are also machine washable at 30 degrees. Please allow to dry naturally, do not bleach, tumble dry, iron or dry clean.

• Plastic and metal parts of the pushchair may be sponged clean with warm water and a mild detergent.

• Never clean with abrasives, ammonia or bleach based and spirit-type cleaners.

• Allow all parts to dry thoroughly before storing.

• After exposure to wet or damp conditions, leave the stroller fully opened in a warm, well ventilated environment. Dry it off with a soft, lint free and absorbent cloth. Residual moisture, left unattended, will encourage mildew or rust to form, damaging the stroller.

Peach Inst AUS Print V4.indd 41

iCandy Peach

41

21/07/2011 20:25

iCandy

Peach

Section 11 – Important Safety Information

ImPortant: read these instructions carefully before use and keep them for future reference.

Your child’s safety may be affected if you do not follow these instructions.

The iCandy Peach stroller is intended for children from birth up to

15kg’s (3 years approximately).

This iCandy Peach chassis is suitable for use with the Peach main seat unit, Peach main bassinette and Maxi Cosi Mico and

Safe & Sound Unity infant carrier car seats.

The Peach chassis is also compatible with the Peach Blossom

“Pip” converter bars, Peach Blossom lower seat unit, Peach

Blossom Twin Bassinettes and 2 x Maxi Cosi Mico or Safe &

Sound Unity infant carrier car seats as a tandem stroller.

Important: The iCandy Peach and Peach Blossom travel systems should only be used in the configurations shown in this booklet.

Using alternative non-approved configurations or modifying your product in any way could cause a hazard and may affect your warranty.

WarnIng:

to avoID InjurY or DEatH:

alWaYs aPPlY tHE BraKEs WHEnEvEr tHE strollEr Is statIonarY or WHEnEvEr You

ParK tHE strollEr.

Do not lEavE cHIlDrEn unattEnDED.

sEcurE tHE cHIlD In tHE HarnEss at all tImEs.

42

iCandy

Peach

Peach Inst AUS Print V4.indd 42 21/07/2011 20:25

iCandy

Peach

Do not carrY EXtra cHIlDrEn or Bags on tHIs strollEr.

maKE surE cHIlDrEn arE clEar oF anY movIng Parts IF You aDjust tHE strollEr, otHErWIsE tHEY maY BE

InjurED.

WarnIng: usE tHE HarnEss at all tImEs.

WarnIng:

WHEn not In usE

DIsconnEct sHoulDEr straPs From tHE

WaIst straP anD BucKlE

WarnIng:

Do not usE tHE IcanDY

PEacH maIn or Blossom sEat WItH anY otHEr moDEls oF strollEr.

WarnIng:

Do not usE tHE PEacH maIn or “Blossom” BassInEttE oncE tHE cHIlD can sIt uP unaIDED.

Important safety information about your icandy Peach

This vehicle is intended for children from birth up to 15kg’s

(3 years approximately).

Maximum weight for basket - 5kg (11lbs).

Parcels, accessory items or both if placed on the unit may cause it to become unstable. Please do not hang any bags from the handle of the stroller.

iCandy Peach

43

21/07/2011 20:25 Peach Inst AUS Print V4.indd 43

iCandy

Peach

Please do not let your child play with this product.

Do not use any replacement parts or accessories other than those approved by or supplied by iCandy. Using nonapproved parts or accessories may damage your pushchair or make it unsafe.

Ensure that the parking device is always engaged when loading or unloading your child.

When assembled as a single stroller this unit is designed to carry 1 child only. Additional children should never be allowed to ride on the pushchair.

When assembled as a Blossom or Blossom Twin stroller this unit is designed to carry a maximum of 2 children.

Additional children should never be allowed to ride on the pushchair.

Do not use the stroller if any part is broken, torn or missing.

Contact your stockist for further advice or repair.

Ensure that all locking devices are engaged before use.

Always check that the bassinette(s), seat unit(s) or infant carrier attachment devices are correctly engaged before use.

Always use the tether strap to stop the stroller rolling away.

Take care when using the iCandy Peach stroller on stairs or escalators and never try to lift this stroller by the bumper bar.

Do not use the iCandy Peach stroller near open fires or exposed flames.

Parcels, accessory items, or both if placed on the stroller may cause it to become unstable.

44

iCandy

Peach

Peach Inst AUS Print V4.indd 44 21/07/2011 20:25

iCandy

Peach

Excessive weight may cause a hazardous unstable condition to exist.

Any load attached to the handle affects the stability of the pram/pushchair.

When using the icandy Bassinettes

NEVER add any additional mattress, pillow, comforter or padding. Use ONLY the mattress pad provided by the manufacturer.

Maximum thickness of main bassinette mattress - 30mm.

Maximum thickness of Blossom bassinette mattress - 25mm.

Strings can cause strangulation! Do not place items with string around the child’s neck, such as hood strings or pacifier cords.

Do not suspend strings over a bassinette or attach strings to toys.

iCandy Peach bassinettes are not intended for use as an infant restraint device in a motor vehicle.

The iCandy main and Blossom bassinettes are only suitable for use on the iCandy Peach chassis and iCandy Peach Blossom converter bars.

Peach Inst AUS Print V4.indd 45

iCandy Peach

45

21/07/2011 20:25

iCandy

Peach

Warranty

Your product warranty is our quality promise to you. We guarantee that this product is free from defects in workmanship and manufacturing materials at the time of purchase. During the production process your product was subject to various quality checks however if despite our best efforts your product shows signs of material or manufacturing fault within the warranty period we will comply with the warranty terms & conditions. For further details of these conditions please contact your local approved stockist.

After purchasing your product(s), please keep the original receipt safe in the pocket in the back of the warranty wallet. The date of purchase should be clearly visible and is of importance to check when the product was purchased.

Your iCandy products are automatically covered from the date of purchase by a warranty against material or manufacturing defects.

The warranty is offered in addition to and does not affect your statutory rights.

We would encourage all customers to register their iCandy product on-line using your serial number which can be found on the packaging of each iCandy item, on the shopping basket frames of the chassis, on the base boards of the bassinettes and on the seat boards beneath the seat units.

Warranty Terms

Chassis and seat frames - 24 consecutive months.

Seat fabrics, bassinette converter fabric, bassinette and accessories

- 6 months.

Receive an additional 6 months warranty on your chassis and seat frame(s) by registering your product with us within 6 months of purchase.

What Your Warranty Does Not Cover

Damage caused by normal wear and tear, accidental damage, improper use and damage caused by negligence, misuse and by not following the maintenance instructions.

46

iCandy

Peach

Peach Inst AUS Print V4.indd 46 21/07/2011 20:25

iCandy

Peach the warranty is not valid in the following situations:

1. In case of use or purpose other than described in the instruction manual.

2. If the product is submitted for repair through a retailer / distributor that is not approved or authorised by us.

3. If repairs have been carried out by third parties or a retailer who is not authorised or approved by us.

4. If you have purchased your product over the internet from an unauthorised stockist, or have purchased 2nd hand.

Where Your Warranty Applies

Your warranty applies in the country of purchase only. The warranty applies to the first owner and is not transferable.

What to Do in Case of Defect

If you feel there is a problem with your iCandy product please contact your original approved stockist.

Important Information

Where repairs are carried out, this does not give automatic entitlement to extension of the warranty.

Disclaimer

Whilst we believe the information contained within our product specifications to be correct & reliable at time of print, we are not responsible for its accuracy and we shall not be liable for its interpretation and its use. We reserve the right, at our sole discretion, to change, modify, add or delete product specifications at any time without further notice.

Customer feedback

We are continually looking at ways to improve our iCandy product range and welcome feedback on design, materials, user friendliness and our instructions as well as your own iCandy experience. If you have any feedback, please write to us at the address on the back of this manual.

iCandy Peach

47

Peach Inst AUS Print V4.indd 47 21/07/2011 20:25

iCandy

Peach

The iCandy Peach is a quality product of British design and is distributed by Tobil & Co. Pty Ltd.

For further technical information please contact your place of purchase, “E-mail: [email protected]” or visit www.icandyworld.com/au.

Imported into and distributed in Australia by:

Tobil & Co Pty Ltd,

3 Plane Tree Avenue,

Dingley Village,

Victoria 3172.

Peach Inst AUS Print V4.indd 48 21/07/2011 20:25