CKD9917BK CKD9917

CKD9917BK CKD9917
TM
SmartSet® Dual Alarm Clock Radio
with CD Player
(U.S. Patent No. 6,567,344)
OWNER'S MANUAL
CKD9917BK
CKD9917
Visit our web site at www.emersonradio.com
CAUTION
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENTFIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to
alert the user to the presence of
uninsulated dangerous voltage
within the products enclosure that
may be of sufficient magnitude to
constitute a risk of electric shock
to persons.
WARNING: TO REDUCE THE
RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER
(OR BACK), NO USER
SERVICEABLE
PARTS
INSIDE REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within
an equilateral triangle is
intended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
The Caution Marking may be located at the bottom enclosure of the apparatus.
Les précautions d’emploi sont inscrites en bas de l’appareil.
IMPORTANT SAFETY INSTRUCTIONS
1.) Read these instructions. Keep these instructions. Follow all instructions. Heed all warnings.
2.) Do not use this apparatus near water.
3.) Clean only with dry cloth.
4.) Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
5.) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
6.) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
7.) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
8.) Only use attachments / accessories specified by the manufacturer.
9.) Unplug this apparatus during lightning storms or when unused for long periods of time.
10.) Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
11.) This appliance shall not be exposed to dripping or splashing water and no object filled with
liquids such as vases shall be placed on the apparatus.
L’appqreil ne doit pas être exposé aux écoulements ou éclaboussures et aucun objet ne
contenant de liquide,tel qu’un vase, ne doit être placé sur l’objet.
12.) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
1
13.) Do not overload wall outlet. Use only power source as indicated.
14.) Use replacement parts as specified by the manufacturer.
15.) The product may be mounted to a wall only if recommended by the manufacturer.
16.) Upon completion of any service or repairs to this product, ask the service technician to
perform Safety
17.)
This is CLASS II apparatus with double insulation, and no protective earth provided.
Before We Begin
Thank you for purchasing this Emerson audio product. The Emerson brand is your
assurance of quality, performance and value.
Our engineers have included many useful and convenient features in this product.
Please be sure to read this Owner's Manual completely to make sure you are getting
the maximum benefit from each feature.
This product was manufactured using the highest quality components and standards of
workmanship. It was tested by Emerson inspectors and found to be in perfect working
order before it left our factory. However, there is always the chance that some
problem may occur because of rough handling during shipment to the retail store or to
the final consumer.
If, after reading this Manual, you experience any problems with the operation of this
product, please refer to the instructions for obtaining service at the end of this Manual.
Emerson and Emerson retailers are committed to your satisfaction.
2
IMPORTANT NOTES
CLASS 1 LASER PRODUCT
This product contains a low power Laser Device.
• Avoid installing this unit in places
• Operate controls and switches as
exposed to direct sunlight or close to described in the manual.
heat radiating appliances such as • Before turning on the power, make
electric heaters, on top of other stereo certain that the power cord is properly
equipment that radiates too much heat, installed.
places lacking ventilation or dusty • When moving the set, be sure to first
areas, places subject to constant disconnect the power cord and remove
vibration and/or humid or moist areas.
cords connected to other equipment.
FCC Information
This equipment has been tested and found to comply with the limits for a class
B digital Device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
3
MPORTANT NOTES
PREPARATION
FOR USE
Unpacking And Set Up
Remove the unit from the carton, and remove all packing materials from the
unit.
Save the carton and packing materials in case the unit ever needs to be
returned for service. Using the original carton and packing materials is the
only way to safely repack the unit for shipment.
Remove any descriptive labels or stickers from the top or front of the unit. Do
not remove any labels from the back or bottom of the cabinet.
Remove any small strips of tape that may have been used to prevent the CD
from opening in transit.
Press the CD door in the area marked OPEN/CLOSE button to open the CD
door and remove the ‘dummy CD’ protection card from the CD player and
discard it. Close the CD door.
Unwind the AC power cord and extend it to its full length.
Place the unit on a stable, level surface such as a table, desk, shelf, etc.,
within easy reach of an AC outlet, out of direct sunlight, and away from
sources of excessive heat, dust, moisture or humidity.
Protect Your Furniture
This model is equipped with non-skid rubber 'feet' to prevent the product from
moving when you operate the controls. These 'feet' are made from
non-migrating rubber material specially formulated to avoid leaving any marks
or stains on your furniture. However certain types of oil based furniture
polishes, wood preservatives, or cleaning sprays may cause the rubber 'feet' to
soften, and leave marks or a rubber residue on the furniture. To prevent any
damage to your furniture we strongly recommend that you purchase small
self-adhesive felt pads, available at hardware stores and home improvement
centers everywhere, and apply these pads to the bottom of the rubber 'feet'
before you place the product on fine wooden furniture.
4
5
Battery Back Up System
This unit uses a single CR2032 battery (included) to maintain the time and
alarm settings in the event that it is accidentally unplugged, or you experience
a temporary power failure. We recommend that you install a well-known brand
of Alkaline battery for longest life and best performance.
Installing and replacing the backup battery
1.) Use screw driver to remove the screw that secures the battery compartment
at the bottom of the unit,and remove the battery compartment.
2.) Insert a new battery in the battery comparment with " + " side facing up.
3.) Insert the battery compartment back into the unit and secure it with the screw.
1
2
3
If the power is interrupted the clock display will go off but the battery will
maintain the clock and alarm time settings. When power is restored the time
display will be correct and your alarm setting will also be maintained.
If you notice that the time display is completely wrong you probably
experienced a power failure with a weak or exhausted battery in the
compartment. Reset the clock and replace the battery as soon as possible.
If you do not change the built in lithium battery
within a reasonable period of time after you see
the ‘flashing’ LOW BATTERY warning indicator,
the lithium battery may become exhausted and
will no longer be able to supply back up power to the SmartSet ® internal
computer. If the unit is disconnected from the AC outlet after the battery is
exhausted, or if power interruption occurs, the SmartSet® memory will be lost
and this clock will need to be reset when the power is restored. Be sure to
install a fresh lithium battery before you reset the clock, otherwise the clock will
need to be reset each time the power is interrupted. If this lithium battery is
exhausted and you experience an interruption in the AC power supply, the
clock will reset itself to its initial default setting when the power restored.
AM
AL2
AL1
MON
6
LOCATION OF CONTROLS AND INDICATORS
7
LOCATION OF CONTROLS AND INDICATORS
1.)
2.)
3.)
4.)
5.)
6.)
7.)
8.)
9.)
10.)
11.)
12.)
13.)
14.)
15.)
16.)
17.)
18.)
19.)
20.)
21.)
22.)
23.)
24.)
25.)
26.)
27.)
28.)
29.)
30.)
31.)
32.)
33.)
34.)
35.)
36.)
37.)
38.)
39.)
40.)
VOLUME Control
DIMMER (HIGH / LOW) Selector Switch
STOP Button
PLAY / PAUSE Button
SNOOZE Button
TUNING Control
LED Display
AUX IN Jack
PHONES Jack
AUX Indicator
CD Mode Indicator
AM TIME Indicator
AL1 (Alarm 1) Indicator
Day of Week Indicator
LOW Battery Indicator
Time / Frequency / Date Display
AL2 (Alarm 2) Indicator
ST (FM Stereo) Indicator
"SLEEP" Function Indicator
PROG (Program) Indicator
RAN (Random) Indicator
REP (Repeat) Indicator
PLAY Indicator
AC Power Cord
ALARM MODE Button
MONTH / DATE Button
TIME ZONE Button
SLEEP Button
CLK ADJ / PROG Button
RADIO / BAND Button
TIME-DN / F.REV Button
TIME-UP / F.FWD Button
ALARM 1 Setting Button
POWER “ON” LED Indicator
ALARM 2 Setting Button
ALARM SET / DISPLAY Button
POWER/ALARM OFF Button
CD Door OPEN / CLOSE
CD Compartment
Speaker
8
OPERATION INSTRUCTIONS
Using The First Time
IMPORTANT: The first time you connect your new SmartSet® clock radio to the
AC outlet the internal computer will automatically set the time correctly for the
Eastern Time Zone, Which is the initial default setting. The display will scan
for a few seconds and then show the correct Day and Time in the Eastern
zone. If you live in the Eastern Time zone, there’s nothing else to do. Your clock
is set correctly and running.
If you do not live in the Eastern Time zone, you must change the default zone
remember the new default zone setting and will always return to that setting
after a power interruption.
Setting The Time Zone
There are 7 times zones programmed into your SmartSet® clock radio as
follows:
ZONE 1 ---- Atlantic Time
ZONE 2 ---- Eastern Time (Default Setting)
ZONE 3 ---- Central Time
ZONE 4 ---- Mountain Time
ZONE 6 ---- Yukon Time
ZONE 5 ---- Pacific Time
ZONE 7 ---- Hawaiian Time
To change the default time ZONE display,
press the TIME ZONE button. The number “2”
will appear on the display indicating that the
default zone is ZONE 2, Eastern Time.
or
Hold the TIME ZONE button and then either press the
buttons until
your own time zone appears on the display, then release the buttons. The clock
display will change to the correct time in the time zone you selected. The clock
will always return to the correct time in the zone you selected after every power
interruption. If you move to different time zone, simply change the default zone
display to the new zone and the SmartSet® will remember that setting for you.
Date Display Adjustment
To view the correct date at any time, press the
MONTH / DATE button. The display changes from
Time to Month and Date. When you release the
MONTH / DATE button. For example, May 21 will
appear as “5. 21”. When you release the MONTH/ DATE button the display
returns to the correct Tme.
Setting The Date: Hold the MONTH / DATE button and then press either the
or
or
buttons to set correct month / date. Continue pressing the
buttons for a few seconds, display digit will change.
9
Year Display Adjustment
To view the correct year, press the MONTH /
DATE and TIME ZONE buttons together. The
display changes from Time to Year. When you
release the MONTH / DATE and TIME ZONE
buttons the display returns to the correct Time.
Setting The Year: Hold the MONTH / DATE and TIME ZONE buttons
or
together. At the same time press the
buttons to set the correct year.
Day of Week Display Setting
The display will show the Day of Week at the b o t t o m o f t h e LED Display.
The Day of Week automatically sets after the month / day setting.
Daylight Savings and Leap Year Adjustments
All Daylight Savings and Leap Year adjustments are made automatically by the
SmartSet® internal computer as follows:
• Start of Daylight Savings Time:
At “2:00 AM” on the 2nd Sunday in March, the clock will automatically advance
to “3:00 AM”.
• End of Daylight Savings Time:
At “3:00 AM” on the 1st Sunday in November, the clock will automatically
reset to “2:00 AM”.
• Leap Year:
At “12:00 Midnight” on February 28th, the calendar display will change to “2 29”.
Manual Time Adjustment
Some people like to set their clocks 5 to 10
minutes fast to make sure that they will always be
on time. Even though the SmartSet® sets the time
by itself, you still have the option of adjusting the
time manually if you wish.
Setting the time: Press the POWER button to the off mode, hold the CLK
or
ADJ button and then either the
buttons to adjust time forward or
or
backward as desired. Each press of the
buttons will change the display
or
time by one minute. If you hold the
buttons the display time will
or
change slowly at first, if you continue holding the
buttons the
display digit will change rapidly.
Note: If you manually adjust the time your new setting is entered into the
SmartSet® memory. If the power is interrupted, the display will return to
your new time setting, not the original setting, when the power is restored.
AM
MON
Dimmer Control
If you find the display to be too bright for sleeping, slide the DIMMER selector
switch to the LOW position. The display DIMMER selector switch is located on
the left of the side cabinet.
10
Listening To the Radio
1.) Press the ALARM OFF/POWER button on
the top panel to turn the unit ‘On’. The
POWER LED indicator will light.
2.) Press the RADIO/BAND button to select the
FM BAND
Radio function. Either the MHz or KHz
indicator will light to show which band is
selected. Press the RADIO/BAND button
again to repeatedly switch between the AM
and FM bands.
3.) Rotate the TUNING control on the right side
AM BAND
panel to tune to the desired station.
4.) Rotate the VOLUME control on the left side panel to adjust the volume level.
5.) If you tune to an FM stereo station, the STEREO (ST) indicator will light.
6.) When you are finished listening press the ALARM OFF/POWER button to
turn the unit ‘Off’ . The POWER LED indicator turns off.
In Radio listening mode, the radio frequency display will appear for
approx. 3 seconds,then the clock time will appear on the display.
Press the ALARM SET / DISPLAY button to show the radio frequency, a few
seconds later the display will show the clock time.
MHz
KHz
AM
ST
MHz
MON
MON
Antenna Information
AM
The AM ferrite bar antenna is inside the cabinet. If AM reception is
unsatisfactory, try turning the entire unit slightly until you find the direction that
provides the best reception for the desired station.
CD AUX
PLAY
REP RAN PROG
SLP
AM
ST
KHz
MHz
AL2
AL1
MON TUE WED THU FRI SAT SUN
FM
The FM antenna is built in to the AC power cord. If the FM reception is weak, try
varying the position and direction of the power cord until you find the strongest
signal.
11
Playing Compact Discs
NOTE: This CD player can read CD-R/RW discs, in addition to normal CDs,
however; the compatibility of CD-R/RW discs may be affected by the type of
software that was used to cr eate the discs, as well as the quality and condition
of the blank media you are using. 100% compatibility cannot be guaranteed.
This is not an indication of a problem with the player.
Normal Playback
1.) Press the ALARM OFF/POWER button to switch the unit ‘On’. The
POWER indicator will light.
2.) Press the
button to enter CD playing mode
3.) Press on the CD door in the area marked
OPEN to open the door. If you have not
already done so, remove the ‘dummy CD’
transit protection card from the CD player and
discard it.
4.) Place your disc on the center spindle with the printed label side facing up.
Press down near the center of the disc to make sure it is firmly ‘seated’ on
the spindle, press OPEN area to close the CD door.
5.) The “ – –” of “cd – –” flashes while the player
reads the disc. The display will show the total
number of tracks for a few seconds and then
return to the correct time. To see the track number
at any time during playback press the ALARM
SET/DISPLAY button. The track number will
appear for several seconds and then the
display returns to the correct time.
MON
CD
MON
CD
MON
NOTE: If the disc is inserted incorrectly, or if
the disc is badly scratched and cannot be
read by the player, “d ISC” will appear on the
display for a few seconds, and then the
display returns to the correct time.
6.) Press the
button to begin playback. The
display will briefly show “cd: 01” (Track 1)
and playback on track 1 begins. After a few
seconds the display returns to the correct
time.
12
CD
MON
CD
MON
PLAY
7.) To Pause briefly during playback press the
button. The “ PLAY ” indicator flashes and
after a few seconds the display returns to
correct time. The sound stops, but the disc
continues to spin. Press
button again to
cancel pause and resume playback.
or
8.) To skip forward or backward to other tracks repeatedly press the
buttons until the desired track number appears in the display. Playback will
begin on the selected track.
9.) To stop playback at any time press the
button. After the last track has
played the disc stops automatically. Press the OPEN area of CD door to
open the CD door and remove your disc.
CD
PLAY
MON
CD
To Start Playback From A Specific Track
Load your disc and wait until the display shows
the total number of tracks.
or
Press the
buttons to select the desired
track. While the track number is still appearing
press the
button. Playback will begin on the
selected track and continue until the end of the
disc.
MON
CD
MON
High Speed Music Search
You can search rapidly forward or backward within a track to locate a specific
music passage.
or
Press and hold the
buttons to begin high speed search. The
display will show the current track and the player moves rapidly forward or
or
backward. When you reach the desired passage release the
button
and normal playback resumes.
NOTE: The volume level is automatically reduced during high speed
music search.
13
Repeat Playback
You can program the player to repeat a single track or the entire disk
continuously.
One Track Repeat
or
1. During CD disc playback, press the
buttons to select the track
to be repeated.
2. Press the ALARM MODE button until the
REP (repeat) indicator blinks. The unit will
begin playing the desired track.
3. To cancel the setting, press the ALARM MODE
button until REP indicator is off.
CD
PLAY
REP
MON
All Tracks Repeat
1. During CD disc playback, press the
ALARM MODE button until the REP (repeat)
indicator light is on. The unit will repeat all
tracks.
2. To cancel the setting, press the ALARM MODE button until REP (repeat)
indicator is off.
CD
PLAY
REP
MON
Random Playback
CD
PLAY
RAN
To listen to the tracks on a disc in random order
1. During CD disc playback, press the
ALARM MODE button until the RAN (random)
indicator is light on. The unit will begin playing all tracks randomly.
2. To cancel the setting, press the ALARM MODE button until the
RAN (random) indicator is off.
MON
14
Programmed Playback
The CD player in this unit has a 20 track programmable memory which allows
you to program any disc to play just the tracks you want to hear in the exact
order that you want to hear them. You may program a track or tracks to play
more than once if desired.
NOTE: Programming can only be done while the player is in the Stop
mode. If a disc is playing press the
button to stop playback before
performing the programming steps below.
1) Turn the unit ‘On’, press the
button to select CD function and load the
desired disc in the player. Wait until the player reads the disc and the
display shows the total number of tracks.
2) Press the CLK.ADJ/PROG. button. The
PROG. indicator will flash and the Number “1”
will show on the display, indicating that
you can select the first track to be
programmed.
or
3) Press the
buttons to select the first track. The desired track
number appears on the display.
4) Press the CLK.ADJ/PROG. button again. The selected track is entered in the
Program memory, a s number 01. Then display advances to “2” indicating
that you can select the next track to be programmed.
5) Repeat Steps 3 and 4 to program up to 20 tracks in the memory.
6) After you have programmed all of the desired
tracks press the
button to begin
programmed playback. The PROG indicator
stops flashing and remains lit. Playback
will begin on the first track you programmed
and continue until all programmed tracks have been played.
As each programmed track starts playing the display will briefly show the track
number being played and then return to the correct time.
PROG
CD
MON
CD
PLAY
PROG
MON
CD
PLAY
PROG
PROG
AM
MON
MON
NOTES:
• After all programmed tracks have played the player stops but the program
remains in the memory.
Press the CLK.ADJ/PROG. button and then the CD PLAY/PAUSE button to
begin programmed playback again.
• To clear the programmed tracks from the memory, press the STOP
button again or open the CD door. Pressing the ALARM OFF/POWER
button will shut the unit ‘ Off’ , or switching to the Radio function also
clears the program.
15
Alarm Operation
Setting the ALARM Time (Wake Up time)
AM
This clock radio has two separate wake-up
alarms that can be set and used independently.
To set or adjust the wake-up times please proceed as follows:
Check the Alarm Time : During CD playing or radio listening, press ALARM
1/ ALARM2 buttons to show alarm time in display.
Alarm time setting: Press the POWER button to off mode, hold the ALARM 1/
or
buttons to adjust alarm time
ALARM2 buttons and then press either the
or
forward and backward as desired. Each press of the
buttons will
or
change the display time by one minute. If you hold the
buttons the
display time will change slowly at the first, but if you continue holding the
or
buttons the display digit will change rapidly.
NOTE: If Alarm 1 and Alarm 2 are set in same alarm time, only Alarm 1 will
sound.
AL1
Activate or Deactivate the Wake-up Mode
AL2
MON TUE WED THU FRI SAT SUN
After you have adjusted the wake-up times on one or both alarms, you must
activate the alarms and select the wake-up mode. You have the option of waking
to the buzzer, radio or CD.
Setting the Wake Up Mode: Press the POWER button to off mode, hold the
ALARM 1/ ALARM2 buttons and press the ALARM SET / DISPLAY button to
select the wake-up mode. Once the wake up mode is activated the AL1 or
AL2 indicator will light on the display.
Wake to Radio : Select a radio station and make sure the volume is set as
desired. Press the POWER button to off mode, hold the ALARM 1/ ALARM2
buttons and press the ALARM SET / DISPLAY button until the AL1 or AL2
indicator turns red.
Wake to CD : Place a CD in the CD compartment and make sure the volume
is set as desired. Press the POWER button to off mode, hold the ALARM 1/
ALARM2 buttons and press the ALARM SET / DISPLAY button until the
AL1 or AL2 indicator turns green.
Wake to Buzzer : Press the POWER button to off mode, hold the ALARM 1/
ALARM2 buttons and press the ALARM SET / DISPLAY button until the
AL1 or AL2 indicator turns amber.
NOTE: If there is no CD inserted, or the CD is damaged, it will automatically
wake to Buzzer.
16
Setting Alarm Mode
Press the POWER button to off mode, hold the ALARM1/ALARM2 button
and press the ALARM MODE button to set the alarm mode
Weekdays only : Alarm will activate on weekdays only
Weekend only : Alarm will activate on weekend only
Everyday : Alarm will activate on all 7 days of a week.
Turn Off Alarm
If the alarm is activated, press POWER button to shut off the alarm, and the
unit will be back in the off mode.
Snooze/Repeat Alarm
After the alarm turns on, you can press the
SNOOZE button for a few extra minutes sleep
(AL1 or AL2 indicator will flash). The alarm will
stop for approximately 9 minutes and then repeat.
Snooze operation can be repeated several times if desired, but after
one hour the alarm will not turn ‘On’ again.
AM
AL1
AL2
MON
Sleep To Music Timer
You can use the sleep timer to play the Radio or CD player up to 90 minutes
and have the unit shut off automatically.
1.) Press the ALARM OFF/POWER button to turn the power ‘On’ . Operate
the Radio or CD player as usual. Adjust the VOLUME to the desired level.
2.) Press the SLEEP button to start sleep timer
(default 10 minutes).
3.) Hold the SLEEP button and then either the
or
buttons to select the desired
amount of sleep timer from 90 minutes to two
minutes. The SLP(sleep) indicator will show on the display.
4.) When the display shows the desired amount of time, release the SLEEP
button. After 5 seconds the display changes back to the correct time. The
Radio or CD play will continue until the sleep timer counts down to ”00”and
then shut off automatically.
5.) To stop the Radio or CD player before the sleep timer counts down to “00”,
press the ALARM OFF / POWER button to turn the unit “Off”.
NOTE: If the sleep timer is set to CD player, the sound stops when the
disc ends, even if a longer sleep time was selected.
SLP
AM
AL1
17
MON
Auxiliary Input Jack (Connection Cable Not Included)
This unit includes an AUX input jack to allow you to connect external devices,
such as an iPod® or portable MP3 player, and listen to the music stored on
your external device through the speakers of this radio.
Connect the headphone jack of your external device to the AUX input jack
located on the front panel of this unit.
PLAY
CD AUX
REP RAN PROG
SLP
AM
ST
KHz
MHz
AL1
AL2
MON TUE WED THU FRI SAT SUN
IMPORTANT:
When you connect a cable to the AUX input jack of this unit the ‘function’
selector automatically switches from Radio or CD to Auxiliary Input. You
must disconnect the cable from the AUX input jack in order to listen to
the Radio or CD again.
After connecting your external device to the AUX input jack, slowly
adjust both the volume controls on this unit and your external device to
find the desired setting. Please note that if the VOLUME control on this
radio is set to a low level while the VOLUME control on your external
device is set too high, the sound will be distorted.
NOTE: If an external audio source is connected to the AUX (Auxiliary
Input) jack at the wake-up time the alarm will automatically default to the
Buzzer mode, regardless of the mode you selected.
18
Headphone (PHONES) Jack
This unit includes a 3.5mm PHONES (headphone) jack on the front panel. This
allows you to connect a set of stereo headphones (not included) for private
listening without disturbing others. When headphones are connected, the
built-in speakers are automatically disconnected.
CD AUX
PLAY
REP RAN PROG
SLP
AM
ST
KHz
MHz
AL1
AL2
MON TUE WED THU FRI SAT SUN
IMPORTANT! When using stereo headphones always set the volume control
to a low level before you put on the headphones. Then put on the
headphones and gradually adjust the volume control to the desired level.
Remember that prolonged listening with headphones or ear buds at high
volume levels may eventually cause hearing loss
19
CARE AND MAINTEANCE
Compact Disc Care
• To remove a disc from its storage case, press down on the center of the case
and lift the disc out, holding it carefully by the edges.
• Fingerprints and dust should be carefully wiped off the disc’s recorded
surface with a soft cloth. Unlike conventional records, compact discs have no
grooves to collect dust and microscopic debris, so gently wiping with a soft
cloth should remove most particles. Wipe in a straight line from the inside to
the outside of the disc. Small dust particles and light stains will have
absolutely no effect on reproduction quality.
• Clean the disc periodically with a soft, lint-free, dry cloth. Never use
detergents or abrasive cleaners to clean the disc. If necessary, use a CD
cleaning kit.
• Never write on or affix labels to the surface of compact discs.
Care Of The Cabinet
• If the cabinet becomes dusty wipe it with a soft dry dust cloth. Do not use any
wax or polish sprays on the cabinet.
• If the front panel becomes dirty or smudged with fingerprints it may be
cleaned with a soft cloth slightly dampened with a mild soap and water
solution. Never use abrasive cloths or polishes as these will mar the finish of
your unit.
Caution
Never allow any water or other liquids to get inside the unit while cleaning.
20
TROUBLE SHOOTING GUIDE
Symptom
Radio
Noise or sound distorted
on AM or FM broadcasts.
AM or FM, no sound.
Compact Disc Player
CD Player will not play.
Possible Cause
Solution
Station not tuned properly
for AM or FM.
AM: The bar antenna is
not positioned correctly.
Volume at minimum.
Retune the AM or FM
broadcast station.
Reposition the unit until
best reception is obtained.
Increase Volume.
CD is not installed or Insert CD with label side
installed incorrectly.
up.
CD skips while playing.
Disc is dirty or scratched. Wipe disc with cloth or
use another disc.
CD does not shut off when
You must always press
pressing the ALARM OFF / This is normal operation. the STOP button to stop
POWER button during
CD playback, then press
playback.
the ALARM OFF/POWER
button.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-800-898-9020 OR
1-800-695-0098 OR
E-MAIL TO: [email protected]
21
The Serial Number can be found on the bottom of the unit. We Suggest
that you record the Serial Number of your unit in the space below for
future reference.
CKD9917/CKD9917BK
22
TM
CKD9917-906-01
Made In China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement