SBL-MC
Installation Manual
WARNING: DO NOT LIFT FIXTURE BY CABLES.
This could result in permanent damage to both the fixture and the cables. Damage resulting from grasping cables and / or putting undue pressure on the cable connections will not be covered under the warranty!
DO NOT ATTEMPT TO INSTALL OR USE THE SBL-MC FIXTURE WITHOUT READING THE INSTALLATION
INSTRUCTIONS AND SAFETY LABELS COMPLETELY.
Failure to adhere to these instructions could result in serious injury or property damage.
DO NOT MODIFY, ALTER OR ATTEMPT TO SERVICE THE SBL-MC. DOING SO WILL VOID THE WARRANTY.
SBL-MC
INSTALLATION INSTRUCTIONS
SBL-MC
High Powered Solid Color Washer
INTRODUCTION:
The Boca SBL-MC is a powerful instrument developed for large-coverage illumination. This line voltage* fixture eliminates the need for secondary transformers, making installation contractor friendly. The housing is anodized aluminum with a durable finish making it weather and abrasion resistant. The SBL-MC is UL Listed for dry, damp, or wet location (model dependent).
Fixtures must be installed by a qualified and licensed electrician in accordance with all national, state and local electrical codes and regulations. If any part of this manual does not meet the necessary codes and regulations, contact the factory for more information before attempting to install.
MAINTENANCE:
Cleaning:
− Dry and Damp (IP65) Rated Fixtures:
To clean surface use a soft damp cloth.
− Wet (IP68) Rated Fixtures:
To clean surface use a soft cloth with mild soap and water.
Storage: Store in a dry, well-ventilated area when product is not in use. Keep the electrical cord away from heated surfaces when in use or not in use. If cord shows signs of damage do not use, return product to manufacturer.
ELECTRICAL SPECIFICATIONS:
Input Voltage: 90-120VAC or 230-277VAC
1. Total linear ft per 20A breaker: 32ft
2. Total linear ft per 15A breaker: 24ft
3. Input Current: 400mA RMS per linear ft
IP65
DAMP LISTING
IP68
WET LISTING model dependent
Max temp: 55 °C
Min. temp: -40 °C
Turn Power Off At Circuit Breaker Before Beginning Installation!
DO NOT LIFT FIXTURE BY CABLES!
INCLUDED IN THIS PACKAGE
1
SBL-MC MC (solid color)
(In lengths shown on job specific drawings)
2 Mounting Brackets
(2 brackets per fixture)
3
Job Specific Drawings
SBL-MC
DMX In
DMX Out
Power Feed
Page 2 of 5
SBL-MC
INSTALLATION INSTRUCTIONS
1. Install Swivel Bracket into Substrate
1a.
Use four screws (not provided by Boca Flasher) to secure the brackets to the substrate
1b.
Loosen center hinge pin and adjust angle of fixture to focus required. Tighten pin to hold the focus.
Screw Information:
1. Screws are NOT provided by Boca Flasher, Inc.
2. Boca Flasher recommends wide washer flat head Philips screws not to exceed 0.418" in diameter.
3. Length of screw will vary depending on mounting surface.
4. For outdoor installations, installer should use a screw with weather-proof coating.
2. Install Hinge Clips
2a.
Rotate fixture to see bottom and note each label.
▶
2b.
Cross-reference with job specific drawing.
▶
▶
BF-01
◀
▶
Labels on fixtures correspond with nomenclatures on drawings.
▶
Page 3 of 5
SBL-MC
SBL-MC
INSTALLATION INSTRUCTIONS
3. Connect Fixtures Together (as shown on Job Specific Drawings
3a.
Connect DMX IN on a fixture with DMX out separate fixture.
3b.
Push together until you hear a “Click”.
DMX Out
DMX In
DMX Out
DMX In
DMX Out
Power Feed
click!
4. Connect Fixtures to Power - Single Run Installation
◀
DMX In
Page 4 of 5
Important Safety Reminders
SBL-MC
INSTALLATION INSTRUCTIONS
1. DANGER: To reduce the risk electric shock, always unplug the SBL-MC from electrical outlet before cleaning. Cut breaker if outlet is not available.
2. TO REDUCE THE RISK of burns, fire, electric shock, or injury to persons
• Use the SBL-MC only for its intended use as described in these instructions.
• Do not use attachments not recommended by Boca Flasher.
• Never operate the SBL-MC if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. If the seal appears to be damaged/broken/torn return the SBL-MC to a service center for examination or repair.
• Keep cord away from heated surfaces
• Never drop or insert any object into any opening.
• Do not operate where aerosol (spray) products are being used or where oxygen
is being administered.
3. WARNING: Do not attempt to install or use the SBL-MC without reading the installation instructions and safety labels. Failure to adhere to these instructions could result in serious injury or property damage.
4. DO NOT MODIFY , alter, or attempt to service the SBL-MC Doing so will void the warranty.
5. DO NOT USE SHARP TOOLS near or on the fixture lens.
Doing so will result in property damage and void the warranty.
Boca Flasher, Inc.
508 South Military Trail ■ Deerfield Beach, Florida ■ 33442 USA
Phone: 561.989.5338 ■ Fax: 561.982.8323
www.bocaflasher.com
IP65
DAMP LISTING
IP68
WET LISTING
We are constantly improving our fixtures and reserve the right to change options and specifications. Additional information & details at www.bocaflasher.com. For specific requirements, contact your Boca Flasher sales representative. Boca Flasher, Inc. 508 South Military Trail, Deerfield Beach, Florida 33442 USA Phone: 561.989.5338 Fax: 561.982.8323 © 2016 Boca
Flasher, Inc. All rights reserved. All names and trademarks are property of their respective owners. REV-05162016_lr
