ADEMCO 5890PI Installation guide

ADEMCO 5890PI Installation guide
N5987-1 3/98
For use with Q.E.D. control panels only.
Previous Menu
No. 5890PI
PASSIVE INFRARED MOTION
DETECTOR/TRANSMITTER
®
INSTALLATION INSTRUCTIONS
GENERAL INFORMATION
The 5890PI Passive Infrared Motion
Detector/Transmitter is a battery-operated
wireless device intended for use as part of a
5800 series wireless alarm system.
Designed for use in commercial and
residential installations, the 5890PI is a wall mounted unit with a standard lens that
provides wide-angle protection up to a range
of 35 ft (10.6m). For best coverage, mount the
detector so that the likely direction of
intruder motion is across the pattern.
When installed per the guidelines, the Split Zone Optics technology in the 5890PI
provides reasonable false alarm protection
against pets and other animals up to 40 lbs.
This document provides installation
instructions for the 5890PI, but the installer
must be familiar with the installation
instructions for the 5800 Wireless Alarm
System with which the 5890PI is intended to
be used.
FEATURES
• Split-Zone Optics provides pet immunity
•
•
•
•
•
•
against animals up to 40 lbs.
Wireless operation for fast installation.
Dual-element pyro-electric sensor provides
positive protection while minimizing false
alarms.
Alternate polarity pulse count option offers
greater stability in adverse environments.
Provision to turn LED on while WalkTesting (LED is turned off after testing).
Tamper-protected cover – unit transmits
message if cover is removed.
Wall or corner mounting options.
SYSTEM DESCRIPTION
Optical System: Uses efficiently designed
Fresnel lenses with Split-Zone Optics.
Radio Transmitter: The built-in
transmitter serves only as the communication
link to the alarm system's Receiver/Control,
and can send alarm, tamper, supervisory, and
battery status messages to the system's
receiver/control. The transmitter is not used
for detection purposes. Each detector has a
unique ID code permanently assigned at the
factory. You must enroll this ID into the
control system at the time of installation.
This allows each detector used in the system
to be uniquely identified. You must program
the control to enroll the 5890PI as an "RF"
type unit (i.e., supervised RF).
To conserve battery life during normal
operation, no more than one transmission
sequence will occur within a 3-minute period.
There is no such time restriction in "Test"
mode.
Alternate Polarity Pulse Count: Two
jumper-selectable detection response modes
are provided: Instant response (Pulse Count
OFF) and Alternate Polarity Pulse Count
(Pulse Count ON). With Pulse Count OFF,
any detected change in infrared energy will
trigger an immediate alarm signal. This mode
is recommended when the detector is used to
monitor a narrow hallway where coverage is
provided by only a single zone.
Use the Pulse Count ON mode when the
detector is installed in areas where periodic
changes in infrared energy levels are normal
(for example, where forced-air heating ducts
are present). In this mode, at least two
changes in infrared energy must be detected
within a short period before an alarm will be
triggered.
Important Note: For pet immune
applications, Pulse Count ON is
recommended.
SPECIFICATIONS
Pet Immune
Lens :
Pulse Count:
Detectable
Walk Rate:
Mtg. Height:
Walk Test
Indicator:
Batteries:
0perating
Temperature:
Operating
Humidity:
Dimensions:
35 ft x 45 ft
(10.6m x 13.7m).
30 zones (8 long, 7 over 7
intermediate, 4 over 4
short range).
Installer-selectable
On/Off link.
0.5 – 10 ft/sec
(0.15 - 1.5m/sec).
7.0 ft recommended (2.1m),
but may be mounted at
other heights (see Table 1).
Red LED with
Test/Normal (disable) link.
Two 3-volt Lithium
batteries. Use only
Ademco No. 466,
Duracell DL123A,
Panasonic CR123A,
Sanyo CR123A or
Varta CR123A.
32°F – 122°F (0°C - 50°C).
Up to 95% RH (max.), noncondensing.
2-11/16"W x 5"H x 1-7/8"D
68mm x 127mm x 48mm.
25'
(7.6m)
BATTERY INSTALLATION
1.
Remove front cover by inserting a large
screwdriver blade (or small coin) in groove
between cover and base at the location
shown in Figure 2; rotate blade to
override snap fit, then lift cover off.
2. Observing correct polarity, install the
two Lithium batteries (supplied) into the
battery holders, as shown in Figure 5.
Make sure the batteries are firmly seated.
3. Replace the cover (snap fit).
Battery Caution:
Risk of fire, explosion, and burns. Do not
recharge, disassemble, heat above 100°C, or
incinerate. Dispose of used batteries
promptly. Keep away from children.
Programming Note: If you have not
programmed the detector’s ID into the
system (i.e., this is an initial detector
installation), refer to the PROGRAMMING
section below and perform the ID enrolling
procedure before mounting or testing the
detector.
PROGRAMMING
You must enroll the detector’s ID during
installation of the system. You should
program the 5890PI as an “RF” type unit
(i.e., supervised RF). and the "Loop"
number as "1".
To program the detector, place the LED
jumper in the TEST position (see Figure 5),
the Pulse Count jumper in the OFF position,
batteries installed and cover on. Temporarily
cover the lens (a cloth will do) to prevent any
activation by the detector.
With the control in Zone Programming mode,
at the "Input serial number" prompt, remove
the cloth cover and motion your hand over the
lens to activate the detector and cause it to
send a FAULT; then cover the lens again to
send a RESTORE. Repeat this procedure to
confirm the serial number enrolled.
Alternatively, you can enter the serial
number manually.
Return LED jumper to the NORMAL
position.
See the control unit’s installation instructions
for further details.
INSTALLATION HINTS
• Do not install where the detector is exposed
0
ALTERNATE
COUNT POLARITY
EACH ZONE CONSISTS
OF 2 FIELDS
25'
(7.6m)
10'
(3m)
20'
(6m)
30' 35'
(9m) (10.6m)
10'
(3m)
20'
(6m)
30' 35'
(9m) (10.6m)
7.5'
(2.3m)
0
0
Figure 1.
Protection Pattern
1
to direct sunlight or directly above strong
sources of heat.
• Make sure the detection area does not have
obstructions (curtains, screens, large pieces
of furniture, plants, etc.) which may block
the pattern of coverage.
• Avoid locating a unit in areas which
contain objects likely to produce a rapid
change in temperature, such as central
heating, radiators, or ducts (or heaters of
any kind), air conditioners, open flame, etc.
• Do not mount on an unstable surface.
INSTALLATION
IMPORTANT: For installation with pets, be
sure to follow the guidelines described in
Table 2.
Radio Transmission Path Check
Verify that a strong transmission path
between the 5890PI and the system's
Receiver/Control exists before permanently
mounting the detector. Do this by
performing the Walk-Test (described later)
with the detector temporarily mounted in its
proposed location. The 5890PI will transmit
when sensing motion (waving an arm or
walking into an area). Sometimes, moving the
detector only a few centimeters means the
difference between a strong and weak
transmission path. Experiment until you are
satisfied that the location provides the
strongest transmission path, yet is still
practical for the protection pattern desired.
This test also verifies that the detector has
been correctly programmed into the system.
Recess Mounting
Lens Masking
Recessed mounting requires the use of the
optional No. 1990MK Recess Mounting Kit.
Complete instructions for the use of this kit
accompany it. Note: Holes "C" in the
detector base (accessible only when the PC
board is removed) are used for recessed
mounting.
The supplied masking strips are designed for
application to one or more lens segments to
produce a protection pattern that suits the
particular requirements of the protected area.
Individual masking strips have been provided
for each of the lens segments on the standard
lens supplied with the PIR. Simply peel off
the appropriate pressure-sensitive adhesive
strip(s) and apply over the desired lens
segment(s). Be sure to affix the masking
strips to the inside of the lens (not the outer,
smooth side). Each lens segment that is
masked results in the elimination of one zone
of protection from the coverage pattern. By
masking segments of the lens, you can adjust
the coverage to suit the area to be protected,
or eliminate coverage from areas where you
anticipate environmental disturbances that
might reduce the PIR's stability (a heater or
other heat-producing object, for example).
Changing Lenses (if required)
1.
2.
3.
4.
Normal Mounting
Mount the unit to a firm vertical surface (flat
on a wall or in a corner).
1. Remove the front cover.
2. Temporarily loosen (do not remove) the
screw holding the PC board in the
detector base (see Figure 5 for location of
this screw).
The board can then be moved up or down
for access to the knockout mounting holes
in the base.
3. Refer to Figure 3 for location of knockout
holes in the base. Break out only those
holes required.
4. Mount the detector with screws, using the
selected mounting holes.
5. Before fully tightening the PC board
holding the screw, make sure the board is
positioned so that the arrow is in line with
the appropriate setting on the graduated
scale on the right-hand side of the PC
board (see Table 1 and Figure 5).
5.
6.
7.
Remove front cover.
Squeeze upper lens lock located in front
cover to release upper Fresnel lens
support. Squeeze lower lens lock to
release lower Fresnel lens support (see
Figure 4).
Note how the lens supports are
positioned, then remove the supports.
Carefully remove the existing lens and
replace it with an optional coverage
replacement lens. The lens must be
installed with the smooth side facing
outward . Also, the lens should be oriented
with its part number on the upper right hand side (see Figure 4). Be sure to center
the lens.
Note: Lens surface should be free of dirt,
foreign matter and fingerprints. Use a
clean dry soft cloth to wipe lens surfaces,
if required.
Replace top and bottom lens supports and
then press downward so that the lens
locks snap into position, thus securing the
lens in place.
Refer to Table 1 for recommended PIR
mounting height.
Replace the front cover (make sure the
cover snaps tightly).
The protection pattern provided by the lens
can be moved to the left or right by horizontal
adjustment of the lens, as follows:
1. Remove front cover.
2. Press inward on the upper and lower lens
locks at the left or right side only to
release the lens supports on one side. Now
slide the lens to the left or right, as
needed. The lens may be moved as much
as 8° from center in either direction.
3. When the lens is in the desired position,
press the lens locks downward on the
released side to lock the supports in place.
4. Replace the front cover (make sure the
cover snaps tightly).
After any adjustment, you must conduct a
Walk-Test to ensure proper coverage of the
area to be protected, as indicated under "Test
Procedures."
PULSE COUNT OPTION
Figure 4. Changing Lenses
Figure 2. Cover Removal
Horizontal Adjustment of Lens
Each detector includes Pulse Count circuitry
that is designed to provide stability in
adverse environments to minimize false
alarms. Pulse count is selected by positioning
a jumper across the ON pulse count terminals
(shown in Figure 5). When set for pulse
count ON, the detector will signal an alarm
within 2 or 3 steps, since the processing logic
requires more complex motion than just a
momentary event. When the detector verifies
an intrusion, the built-in transmitter will
send an alarm message to the
control/receiver.
Important Note: For installations with
pets, Pulse Count ON is recommended.
Vertical Pattern Adjustment
LED DISABLE
The protection pattern provided by the lens in
use can be raised or lowered by repositioning
the PC board in the detector. A graduated
scale to the right of the board (see Figure 5)
indicates the approximate number of degrees
by which the pattern can be raised (max. +5°)
or lowered (max. -15°). The detector is
normally shipped with the board set to the 0°
position. To make this adjustment, remove
the cover on the detector and loosen the screw
holding the PC board (the screw is located at
the approximate center of the board). Slide
the board upward or downward by the
number of degrees required, then tighten the
holding screw again. After any adjustment,
you must conduct a Walk-Test to ensure
proper coverage of the area to be protected, as
indicated under "Test Procedures."
The detector is shipped with the LED
disabled (LED jumper in the "NORMAL"
position). The LED may be enabled (for the
Walk-Test) by positioning the LED jumper in
the "TEST" position (see Figure 5).
Note: When the jumper is in the "NORMAL"
position, the LED will not light, but the built in transmitter will transmit alarms when the
PIR senses motion.
Figure 3. Mounting Holes in Base
2
from the system's console, verifying that the
PIR's transmitter signal has reached the
control's wireless receiver.
The absolute range of all PIR units is subject
to variation because of different types of
clothing, backgrounds and ambient
temperature. For this reason, ensure that the
most likely intruder routes are well within
the PIR's protective zones and that Walk Testing is carried out along these routes.
Walk-Test
Figure 5. PC Board
TEST PROCEDURES
Important: Testing should be conducted with
the protected area cleared of all people. Place
the protective system's control in the Test
mode for the Walk-Test procedure. When the
PIR senses movement, a beep will be heard
1. Remove front cover and set the pulse
count jumper in the detector in the OFF
position initially. The LED must be
enabled at this time (jumper in the TEST
position).
2. Replace front cover and walk through
protective zones, observing that the
detector's LED lights whenever motion is
detected (the LED serves as a Walk-Test
indicator during this procedure).
3. If pulse count is going to be used in this
installation, set the pulse count jumper to
the ON setting and repeat the Walk-Test
procedure.
Note: If pulse count mode is used during
the Walk-Test, the LED will stay lit for
4.
approximately 1 to 3 seconds after
detecting motion.
After the Walk-Test is completed, the
LED jumper should be placed in the
NORMAL position (LED disabled).
MAINTAINING PROPER OPERATION
In order to maintain the detector in proper
working condition, it is important that the
user observes the following:
1. Replace both batteries within 7 days
after a "low battery" message has
appeared in the system's display.
2. Detectors should never be re-aimed or
relocated without the advice or assistance
of the alarm service company.
3. The physical surroundings of the
protected area should not be changed. If
furniture or stock is moved, or air conditioning or additional heating is
installed, the PIR may have to be
readjusted.
4. Walk-Tests should be conducted
frequently (at least weekly) to confirm
continued proper coverage.
TABLE 1. INSTALLATION GUIDE FOR MOUNTING HEIGHTS
Lens
Part
No.
5890PI
(Standard
as installed)
Description/
Coverage
Pulse
Count
PET IMMUNE LENS
35 ft x 45 ft
(10.6m x 13.7m)
Req'd for
installations
with pets
PIR
Mounting Height
Pattern
Setting
(Deg)
6.5 ft (2.0m)
+2°
7 ft (2.1m)
+1°
† See Figure 5 for
location of
adjustment scale on
PC board (refer also
to "Vertical Pattern
Adjustment")
OPTIMUM PET
IMMUNITY
.
7.5 ft (2.3m)
+1°
TABLE 2. SPECIAL INSTRUCTIONS FOR INSTALLATION WITH PETS
To take full advantage of the pet immunity in the 5890PI, the following guidelines
should be followed:
•
Mount the center of the detector 6-1/2 to 7-1/2 feet high and adjust the vertical angle
according to Table 1.
•
Set the Pulse Count to ON.
•
Mount where animals cannot come within six feet of the detector by climbing on furniture,
boxes, or other objects.
•
Do not aim the detector at stairways, furniture or objects that can be climbed by an animal.
Note: This unit will provide immunity to false alarms for an individual animal or a group of
animals whose total weight is equal to or less than 40 pounds when the room temperature is
above 50° F.
TRO UBLE S HO O TI NG
Trouble 1: INTERMITTENT ALARM
Probable Causes:
A. Rapid temperature change. Check for electric or gas
heaters, open flames, electric arcs, etc.
Remedy: Locate source and reposition detector.
B. Drafts causing drapes, light fixtures, display material to
move.
Remedy: Eliminate source of motion.
Trouble 3: DETECTION AREA CHANGES
Probable Causes:
A. Repositioned furniture or equipment in the protected area.
Remedy: Caution customer about layout changes. Reposition
detector.
B. Mounting surface is unstable. A few degrees of vertical shift can
change range substantially.
Remedy: Mount on secure surface.
Trouble 2: LED INOPERATIVE DURING WALK-TEST
Probable Causes:
A. LED control jumper set to NORMAL.
Remedy: Reposition jumper to TEST position.
B. LED malfunction. Check for broken/shorted leads.
Remedy: Return unit for service.
Trouble 4: UNIT DOES NOT APPEAR TO BE OPERATING
Probable Cause:
A. Unit is not receiving power.
Remedy: Check for appropriate battery voltage. Install new
batteries if necessary. Be sure to change both batteries.
3
LIMITATIONS OF THE PIR MOTION
DETECTOR
While the Intrusion Detector is a highly reliable intrusion
detection device, it does not offer guaranteed protection against
burglary. Any Intrusion Detection device is subject to
compromise or failure to warn for a variety of reasons:
• Passive Infrared Motion Detectors can detect intrusion only
within the designed ranges as diagrammed in this installation
manual.
• Passive Infrared Motion Detectors do not provide volumetric
area protection. They do create multiple beams of protection,
and intrusion can be detected only in unobstructed areas
covered by those beams.
• Passive Infrared Detectors cannot detect motion or intrusion
that takes place behind walls, ceilings, floors, closed doors,
glass partitions, glass doors, or windows.
• Mechanical tampering, masking, painting or spraying of any
material on the lenses, windows or any part of the optical
system can reduce the detection ability of the Passive
Infrared Motion Detector.
• Passive Infrared Detectors sense changes in temperature;
however, as the ambient temperature of the protected area
approaches the temperature range of 90° to 105°F (32° to
40°C), the detection performance can decrease.
• This Passive Infrared Detector will not operate without the
appropriate battery installed, or if the battery is weak or
improperly connected (i.e., reversed polarity).
• Passive Infrared Detectors, like other electrical devices, are
subject to component failure. Even though this equipment is
designed to last as long as 10 years, the electronic
components in it could fail at any time.
We have cited some of the most common reasons that a
Passive Infrared Motion Detector can fail to catch intrusion.
However, this does not imply that these are the only reasons,
and therefore it is recommended that weekly testing of this type
of unit, in conjunction with weekly testing of the entire alarm
system, be performed to ensure that the detectors are working
properly.
Installing an alarm system may make the owner eligible for a
lower insurance rate, but an alarm system is not a substitute for
insurance. Homeowners, property owners and renters should
continue to act prudently in protecting themselves and continue
to insure their lives and property.
We continue to develop new and improved protection devices.
Users of alarm systems owe it to themselves and their loved
ones to learn about these developments.
ADEMCO LIMITED WARRANTY
Alarm Device Manufacturing Company, a Division of Pittway
Corporation, and its divisions, subsidiaries and affiliates
("Seller"), 165 Eileen Way, Syosset, New York 11791, warrants
its products to be in conformance with its own plans and
specifications and to be free from defects in materials and
workmanship under normal use and service for 24 months from
the date stamp con trol on the product or, for products not
having an Ademco date stamp, for 12 months from date of
original purchase unless the installation instructions or catalog
sets forth a shorter period, in which case the shorter period
shall apply. Seller's obligation shall be limited to repairing or
replacing, at its op tion, free of charge for materials or labor,
any product which is proved not in compliance with Seller's
specifications or proves defective in materials or workmanship
under normal use and service. Seller shall have no obligation
under this Limited Warranty or otherwise if the product is
altered or improperly repaired or serviced by anyone other than
Ademco factory service. For warranty service, return product
transportation prepaid, to your nearest authorized Ademco
distributor.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF
MERCHANTABILITY, OR FITNESS FOR A PARTICULAR
PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF. IN NO CASE
SHALL SELLER BE LIABLE TO ANYONE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR
BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS
OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY
WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS
CAUSED BY THE SELLER'S OWN NEGLIGENCE OR
FAULT.
Seller does not represent that the products it sells may not be
compromised or circumvented; that the products will prevent
any personal injury or property loss by burglary, robbery, fire or
oth erwise; or that the products will in all cases provide
adequate warning or protection. Customer un derstands that a
properly installed and maintained alarm may only reduce the
risk of a bur glary, robbery, fire or other events occurring
without providing an alarm, but it is not insurance or a
guarantee that such will not occur or that there will be no
personal injury or property loss as a result. CONSEQUENTLY,
SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL
INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED
ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING.
HOWEVER, IF SELLER IS HELD LIABLE, WHETHER
DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE
ARISING UNDER THIS LIMITED WARRANTY OR
OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN,
SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE
EXCEED THE PURCHASE PRICE OF THE PRODUCT,
WHICH SHALL BE THE COMPLETE AND EXCLUSIVE
REMEDY AGAINST SELLER. This warranty replaces any
previous warranties and is the only warranty made by Seller on
this product. No increase or alteration, written or verbal, of the
obligations of this Limited Warranty is authorized.
ALARM DE V I CE MANUFACTURI NG CO .
A DIVISION OF PITTWAY CORPORATION
165 Eileen Way, Syosset, New York 11791
Copyright © 1998 PITTWAY CORPORATION
àN5987-1Yä
N5987-1 3/98
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement