Toshiba E205 User manual

Add to my manuals
243 Pages

advertisement

Toshiba E205 User manual | Manualzz

Toshiba Personal Computer

Satellite E200/E205

(PSE20)

(PSE25)

Maintenance Manual

TOSHIBA CORPORATION

S/ No

Satellite/E200/E205 Maintenance Manual

Copyright

© 2009 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein.

Toshiba Satellite E200/E205 Maintenance Manual

First Edition NOV 2009

Disclaimer

The information presented in this manual has been reviewed and validated for accuracy. The included set of instructions and descriptions are accurate for the Toshiba Satellite E200/E205 at the time of this manual's production. However, succeeding computers and manuals are subject to change without notice. Therefore, Toshiba assumes no liability for damages incurred directly or indirectly from errors, omissions, or discrepancies between any succeeding product and this manual.

Trademarks

Intel and Pentium are registered trademarks of Intel Corporation.

IBM, IBM PC/XT, PC/AT, PS/2 and OS/2 are registered trademarks of IBM Corporation.

Windows Vista home edition are registered trademarks of Microsoft Corporation.

Sound Blaster and Pro are trademarks of Creative Technology Ltd.

UNIX is a registered trademark of X/Open Company Ltd.

NetWare are registered trademarks of Novell, Inc.

All other properties are trademarks or registered trademarks of their respective holders.

ii Satellite/E200/E205 Maintenance Manual

Preface

This maintenance manual describes how to perform hardware service maintenance for the

Toshiba Personal Computer Satellite E200/E205, referred to as Satellite E200/E205 in this manual.

The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field.

SAFETY PRECAUTIONS

Four types of messages are used in this manual to bring important information to your attention. Each of these messages will be italicized and identified as shown below.

DANGER: “Danger” indicates the existence of a hazard that could result in death or serious bodily injury, if the safety instruction is not observed.

WARNING: “Warning” indicates the existence of a hazard that could result in bodily injury, if the safety instruction is not observed.

CAUTION: “Caution” indicates the existence of a hazard that could result in property damage, if the safety instruction is not observed.

NOTE: “Note” contains general information that relates to your safe maintenance service.

Improper repair of the computer may result in safety hazards. Toshiba requires service technicians and authorized dealers or service providers to ensure the following safety precautions are adhered to strictly.

 Be sure to fasten screws securely with the right screwdriver. If a screw is not fully fastened, it could come loose, creating a danger of a short circuit, which could cause overheating, smoke or fire.

 If you replace the battery pack, RTC battery or backup battery, be sure to use only the same model battery or an equivalent battery recommended by Toshiba. Installation of the wrong battery can cause the battery to explode.

Satellite/E200/E205 Maintenance Manual iii

The manual is divided into the following parts:

Chapter 1 Hardware Overview describes the Satellite E200/E205 system unit and each FRU.

Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve

FRU problems.

Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service.

Chapter 4 Replacement Procedures describes the removal and replacement of the

FRUs.

Appendices The appendices describe the following:

 Handling the LCD module

 Board layout

 Pin Assignments

 Keyboard scan/character codes

 Key layout

iv Satellite/E200/E205 Maintenance Manual

Conventions

This manual uses the following formats to describe, identify, and highlight terms and operating procedures.

Acronyms

On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example:

Read Only Memory (ROM)

Keys

Keys are used in the text to describe many operations. The key top symbol as it appears on the keyboard is printed in boldface type.

Key operation

Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus (+) sign. For example, Ctrl + Pause

(Break) means you must hold down Ctrl and at the same time press Pause (Break). If three keys are used, hold down the first two and at the same time press the third.

User input

Text that you are instructed to type in is shown in the boldface type below:

DISKCOPY A: B:

The display

Text generated by the XXXXX that appears on its display is presented in the type face below:

Format complete

System transferred

Satellite/E200/E205 Maintenance Manual v

Table of Contents

Chapter 1 Hardware Overview

1.1 Features ..............................................................................Error! Bookmark not defined.

1.2 System Unit Components ..................................................Error! Bookmark not defined.

1.3 2.5-inch HDD.....................................................................Error! Bookmark not defined.

1.4 DVD Super Multi (+-R Double Layer)..............................Error! Bookmark not defined.

1.5 Power Supply .....................................................................Error! Bookmark not defined.

1.6 Batteries .............................................................................Error! Bookmark not defined.

1.6.2 Battery Charging Control .......................Error! Bookmark not defined.

Chapter 2 Troubleshooting

2.1 Outline ......................................................................Error! Bookmark not defined.

Procedure 1 Power Icon Check.............................Error! Bookmark not defined.

Procedure 2 Connection Check.............................Error! Bookmark not defined.

Procedure 3 Replacement Check ..........................Error! Bookmark not defined.

Procedure 1 Message Check .................................Error! Bookmark not defined.

Procedure 2 Test Program Check .........................Error! Bookmark not defined.

Procedure 3 Replacement Check ..........................Error! Bookmark not defined.

2.5 HDD .........................................................................Error! Bookmark not defined.

Procedure 1 Message Check .................................Error! Bookmark not defined.

Procedure 2 Partition Check .................................Error! Bookmark not defined.

Procedure 3 Format Check....................................Error! Bookmark not defined.

Procedure 4 Test Program Check .........................Error! Bookmark not defined.

vi Satellite/E200/E205 Maintenance Manual

Procedure 5 Connector Check and Replacement Check..... Error! Bookmark not

defined.

2.6 Keyboard ..................................................................Error! Bookmark not defined.

Procedure 1 Test Program Check .........................Error! Bookmark not defined.

Procedure 2 Connector Check and Replacement Check..... Error! Bookmark not

defined.

2.7 Display .....................................................................Error! Bookmark not defined.

Procedure 1 External Monitor Check ...................Error! Bookmark not defined.

Procedure 2 Test Program Check .........................Error! Bookmark not defined.

2.8

Procedure 3 Connector Check and Replacement Check..... Error! Bookmark not

defined.

ODD (Optical Disk Drive) .......................................Error! Bookmark not defined.

Procedure 1 ODD Cleaning Check .......................Error! Bookmark not defined.

Procedure 2 Test Program Check .........................Error! Bookmark not defined.

Procedure 3 Connector Check and Replacement Check..... Error! Bookmark not

defined.

2.9 LAN..........................................................................Error! Bookmark not defined.

Procedure 1 Test Program Check .........................Error! Bookmark not defined.

Procedure 2 Connector Check and Replacement Check..... Error! Bookmark not

defined.

2.10 Finger Print (Optional) .............................................Error! Bookmark not defined.

Procedure 1 Test Program Check .........................Error! Bookmark not defined.

Procedure 2 Connector Check ..............................Error! Bookmark not defined.

Procedure 1 Test Program Check .........................Error! Bookmark not defined.

Procedure 2 Connector Check and Replacement Check..... Error! Bookmark not

defined.

2.12 IEEE 1394 Test ........................................................Error! Bookmark not defined.

Procedure 1 Test Program Check .........................Error! Bookmark not defined.

Procedure 2 Connector Check ..............................Error! Bookmark not defined.

Procedure 1 Test Program Check .........................Error! Bookmark not defined.

Procedure 2 Connector Check and Replacement Check..... Error! Bookmark not

defined.

Satellite/E200/E205 Maintenance Manual vii

Chapter 3 Diagnostic Programs

3.1

3.2

3.3

3.4

3.5

General .....................................................................Error! Bookmark not defined.

Quick Start................................................................Error! Bookmark not defined.

3.2.1 Quick Test ..............................................Error! Bookmark not defined.

3.2.2 Customization Test.................................Error! Bookmark not defined.

3.2.3 Keyboard Layout test .............................Error! Bookmark not defined.

3.2.4 Hotkey Test ............................................Error! Bookmark not defined.

3.2.5 Audio Play Test ......................................Error! Bookmark not defined.

3.2.6 Audio Record Test .................................Error! Bookmark not defined.

3.2.7 DMI Read ...............................................Error! Bookmark not defined.

3.2.8 DMI Write ..............................................Error! Bookmark not defined.

3.2.9 3D Sensor Test .......................................Error! Bookmark not defined.

3.2.10 System Information ................................Error! Bookmark not defined.

3.2.11 View Logs ..............................................Error! Bookmark not defined.

3.2.12 Exit to

Free DOS...................................Error! Bookmark not defined.

3.2.13 The Diagnostics Screen Explanation......Error! Bookmark not defined.

Options .....................................................................Error! Bookmark not defined.

3.3.1 Overview ................................................Error! Bookmark not defined.

3.3.2 Batch Parameters Configuration ............Error! Bookmark not defined.

3.3.3 Item’s Parameters Configuration ...........Error! Bookmark not defined.

3.3.4 Load Batch Parameters...........................Error! Bookmark not defined.

3.3.5 Save Batch Parameters ...........................Error! Bookmark not defined.

3.3.6 LOG Parameters Setting.........................Error! Bookmark not defined.

3.3.7 Specify LOG Viewer..............................Error! Bookmark not defined.

3.3.8 Display LOG File ...................................Error! Bookmark not defined.

3.3.9 LOG Viewer ...........................................Error! Bookmark not defined.

3.3.10 LOG File Sample ...................................Error! Bookmark not defined.

Subtests.....................................................................Error! Bookmark not defined.

System Test ..............................................................Error! Bookmark not defined.

viii Satellite/E200/E205 Maintenance Manual

3.6

3.7

3.8

Memory Test ............................................................Error! Bookmark not defined.

Storage......................................................................Error! Bookmark not defined.

Video ........................................................................Error! Bookmark not defined.

3.9 Communication (COMM) ........................................Error! Bookmark not defined.

3.10 Peripheral .................................................................Error! Bookmark not defined.

3.11 Error Codes and description .....................................Error! Bookmark not defined.

3.12 Quick Test Item List.................................................Error! Bookmark not defined.

Chapter 4 Replacement Procedures

4.1 General .....................................................................Error! Bookmark not defined.

Safety Precautions..................................................Error! Bookmark not defined.

Before You Begin ..................................................Error! Bookmark not defined.

Disassembly Procedures ........................................Error! Bookmark not defined.

Assembly Procedures.............................................Error! Bookmark not defined.

Tools and Equipment .............................................Error! Bookmark not defined.

Screw Tightening Torque ......................................Error! Bookmark not defined.

Colors of Screw Shanks .........................................Error! Bookmark not defined.

4.2

Symbols of Screws on the Computer Body ...........Error! Bookmark not defined.

Symbol examples ...................................................Error! Bookmark not defined.

Battery Pack/Bridge Media ......................................Error! Bookmark not defined.

Removing the Battery Pack ...................................Error! Bookmark not defined.

Installing the Battery Pack .....................................Error! Bookmark not defined.

4.2.2 Bridge Media (SD Card / Memory Stick / xDPicture Card) .......... Error!

Bookmark not defined.

Removing the Bridge Media ..................................Error! Bookmark not defined.

Installing the Bridge Media ...................................Error! Bookmark not defined.

4.3 Keyboard ..................................................................Error! Bookmark not defined.

Removing Keyboard ..............................................Error! Bookmark not defined.

Installing the Keyboard..........................................Error! Bookmark not defined.

Removing the Bottom Cover .................................Error! Bookmark not defined.

Satellite/E200/E205 Maintenance Manual ix

Installing the Bottom Cover...................................Error! Bookmark not defined.

Removing the Display Assembly...........................Error! Bookmark not defined.

Installing the Display Assembly ............................Error! Bookmark not defined.

Removing the Memory Module.............................Error! Bookmark not defined.

Installing the Memory Module ..............................Error! Bookmark not defined.

4.7 Wireless LAN Card ..................................................Error! Bookmark not defined.

Removing the Wireless LAN Card ........................Error! Bookmark not defined.

Installing the Wireless LAN Card .........................Error! Bookmark not defined.

4.8 HDD .........................................................................Error! Bookmark not defined.

4.9

Removing the HDD ...............................................Error! Bookmark not defined.

Installing the HDD.................................................Error! Bookmark not defined.

ODD Bay Module ....................................................Error! Bookmark not defined.

Removing the ODD Bay Module ..........................Error! Bookmark not defined.

Installing the ODD Bay Module ............................Error! Bookmark not defined.

Disassembling the ODD Drive ..............................Error! Bookmark not defined.

Assembling the ODD Drive...................................Error! Bookmark not defined.

Removing the Bluetooth module ...........................Error! Bookmark not defined.

Installing the Bluetooth Module ............................Error! Bookmark not defined.

4.11 CPU Cooling Module and Fan .................................Error! Bookmark not defined.

Remove the CPU cooling module and Fan............Error! Bookmark not defined.

Installing the CPU Cooling Module and Fan.........Error! Bookmark not defined.

4.12 CPU ..........................................................................Error! Bookmark not defined.

Removing the CPU ................................................Error! Bookmark not defined.

Installing the CPU..................................................Error! Bookmark not defined.

Removing the System Board .................................Error! Bookmark not defined.

Installing the System Board ...................................Error! Bookmark not defined.

4.14 Speakers ...................................................................Error! Bookmark not defined.

Removing the Speakers..........................................Error! Bookmark not defined.

x Satellite/E200/E205 Maintenance Manual

Installing the Speakers ...........................................Error! Bookmark not defined.

4.15 Switch Board and Finger Print Board ......................Error! Bookmark not defined.

Removing Switch Board and Finger Print Board ..Error! Bookmark not defined.

Installing Switch Board and Finger Print Board....Error! Bookmark not defined.

4.16 Light Sensor Board and Audio Board ......................Error! Bookmark not defined.

Removing the Light Sensor Board and Audio Board .......... Error! Bookmark not

defined.

Installing the Power Board, Switch Board and Logo LED Board................. Error!

Bookmark not defined.

4.17 DC-IN cable, RGB Board and RJ45 cable ...............Error! Bookmark not defined.

Removing DC-IN cable, RGB Board and RJ45 cable ......... Error! Bookmark not

defined.

Installing DC-IN cable, RGB Board and RJ45 cable .......... Error! Bookmark not

defined.

Open Display Mask................................................Error! Bookmark not defined.

Removing the Display Mask..................................Error! Bookmark not defined.

Installing the Display Mask ...................................Error! Bookmark not defined.

Open LCD module .................................................Error! Bookmark not defined.

Removing the LCD module ...................................Error! Bookmark not defined.

Installing the LCD Module ....................................Error! Bookmark not defined.

4.20 CCD Board and MIC................................................Error! Bookmark not defined.

Removing the CCD Board and MIC......................Error! Bookmark not defined.

Installing the CCD Board and MIC .......................Error! Bookmark not defined.

4.21 LED Board and Card Reader Board.........................Error! Bookmark not defined.

Removing the LED Board and Card Reader Board............. Error! Bookmark not

defined.

Installing the LED Board and Card Reader Board Error! Bookmark not defined.

Satellite/E200/E205 Maintenance Manual xi

Appendices

Appendix A Handling the LCD Module ........................................................................... A-1

Appendix B Board Layout .................................................................................................B-1

Appendix C Pin Assignments.............................................................................................C-1

Appendix D Keyboard Scan/Character Codes .................................................................. D-1

Appendix E Key Layout.....................................................................................................E-1

xii Satellite/E200/E205 Maintenance Manual

Chapter 1

Hardware Overview

1 Hardware Overview ii Satellite/E200/E205 Maintenance Manual

1 Hardware Overview

Chapter 1 Contents

1.1 Features ............................................................................................................................... 5

1.2 System Unit Components ................................................................................................. 12

1.3 2.5-inch HDD.................................................................................................................... 17

1.4 DVD Super Multi (+-R Double Layer)............................................................................. 18

1.5 Power Supply .................................................................................................................... 19

1.6 Batteries ............................................................................................................................ 20

1.6.2 Battery Charging Control ...................................................................... 20

Satellite/E200/E205 Maintenance Manual iii

1 Hardware Overview

Figures

Figure 1-1 ID Parts Description Placement...............................................................................9

Figure 1-2 Computer Block Diagram......................................................................................10

Figure 1-3 System Board Configurations................................................................................11

Figure 1-4 System Unit Block Diagram..................................................................................12

Figure 1-5 SATA HDD ...........................................................................................................17

Figure 1-6 DVD Super Multi Drive ........................................................................................18

Tables

Table 1-1 HDD Specifications ................................................................................................17

Table 1-2 DVD Super Multi Drive Specifications ..................................................................18

Table 1-3 Battery Specifications .............................................................................................20

Table 1-4 Quick/Normal Charging Time ................................................................................21

iv Satellite/E200/E205 Maintenance Manual

1.1 Features 1 Hardware Overview

1.1 Features

Toshiba Satellite E200/E205 is a full size notebook PC based on the mobile Intel Arrandale

Processor, providing high-speed processing capabilities and advanced features. The computer employs a Lithium Ion battery that allows it to be battery-operated for a longer period of time.

The display uses 14.0-inch WXGA HD LCD panel, at a resolution of 1366x768. The Micro-

PGA Socket supports BTO/CTO for the CPU so that the system can be designed to suit your needs.

The computer has the following features:

 Processor

CPU is mobile Intel Arrandale Processor:

Intel Core I5 CPU (1066MHz FSB)

I5-520M(2.40G) Hz

Intel Core I3 CPU (1066MHz FSB)

I3-330M(2.13G) Hz

I3-350M(2.26G) Hz

 Host Bridge System Controller

System Controller: Intel 5 Series Chipset HM55, HM57.

 Graphics

Intel integrated graphics or nVIDIA N11M-GE1 / N11M-LP1 graphics.

 Memory

The computer has two SO-DIMM slots, which come standard with DDR3-1066MHz

(PC3-8500) memory module. DDR3 is driven at 1.5V. It accepts BTO/CTO for your memory requirements. It can incorporate up to 8.0GB of main memory.

Using the following sizes of memory modules:

1024 MB (128M

64) / DDR3-1066MHz

 2048 MB (256M

64) / DDR3-1066MHz

Satellite/E200/E205 Maintenance Manual 5

1 Hardware Overview

1.1 Features

 4096 MB (512M

64) / DDR3-1066MHz

 Hard Disk Drive (HDD)

The computer accommodates 2.5-inch 9.5mm height Serial ATA HDD with following storage capacities:

 160 GB (9.5mm thick) SATA (5,400rpm)

 250 GB (9.5mm thick) SATA (5,400rpm)

 320 GB (9.5mm thick) SATA (5,400rpm)

 400 GB (9.5mm thick) SATA (5,400rpm)

 500 GB (9.5mm thick) SATA (5,400rpm)

 ODD

The computer accommodates a fixed 12.7mm ODD with the following type:

 Slot Loading Type DVD Super Multi +-R Double Layer with Label Flash

™ drive

 Display

LCD display comes in the following type at resolution 1366x768:

 14.0” WXGA HD 1366x768 CSV LED display

 On-Board LAN

The internal LAN supports 10/100Mbit Ethernet, enabling connection to a LAN at up to

100Mbps. It supports Wake-up on LAN from S3/S4/S5 and PXE boot support. This internal LAN has RJ45 jack to directly accommodate a LAN cable, and there is signal reception LED on RJ45 jack.

 Wireless LAN (BTO)

The internal Mini Card slot supports IEEE802.11agn (MOW) / IEEE802.11agn (JPN) /

IEEE802.11bg (WW) / IEEE802.11bgn (WW) cards. The Antenna has two or three wires dual band antenna support for BTO.

Sound System

6 Satellite/E200/E205 Maintenance Manual

1.1 Features 1 Hardware Overview

Realtek ALC272 integrated audio controller supports multimedia. The sound system contains the following:

 Stereo speakers

 Headphone / SPDIF combo jack

 Internal microphone

 External microphone jack

 Keyboard

30 kinds’ countries keyboard, which is Toshiba B5 one.

 Toshiba Touch Pad

Wide Touch Pad.

 Bluetooth (BTO)

Bluetooth wireless technology eliminates the need for cables between electronic device such as desktop computer, printer and mobile phone.

 eSATA / USB Combo Port

This product has one eSATA / USB Combo port, which allows device connection through either eSATA or USB signals of eSATA / USB Combo Port.

 USB Port

The computer has two USB 2.0 ports. It is supported to daisy-chain a maximum of 127

USB devices. The serial data transfer rate is 480Mbps, 12Mbps and 1.5Mbps. These ports support PnP installation and hot plugging.

RGB External Monitor Port

A 15-pin external monitor port is provided, through which the computer automatically recognizes an external VESA DDC 2B compatible monitor.

 HDMI Out Port

A HDMI monitor can be connected to HDMI Out Port on the computer.

Satellite/E200/E205 Maintenance Manual 7

1 Hardware Overview

1.1 Features

 Bridge Media Slot

This slot is for your memory card requirements like SD, Mini-SD, SD-IO, MS, MS Pro,

MMC and XD Cards to provide memory card read on your computer.

 Webcam (BTO)

The computer has an internal camera. It supports VGA (640x480) without Macro module.

 Battery

The computer has a removable 6 Cell Lithium Ion battery pack and an internal RTC battery (rechargeable).

8 Satellite/E200/E205 Maintenance Manual

1.1 Features 1 Hardware Overview

 Figures 1-1/1-2/1-3 and 1-4 show the computer and its system unit configuration, respectively.

Figure 1-1 ID Parts Description Placement

Satellite/E200/E205 Maintenance Manual 9

1 Hardware Overview

1.1 Features

Figure 1-2 Computer Block Diagram

10 Satellite/E200/E205 Maintenance Manual

1.1 Features 1 Hardware Overview

Figure 1-3 System Board Configurations

Satellite/E200/E205 Maintenance Manual 11

1 Hardware Overview 1.2 System Unit Components

1.2 System Unit Components

Figure 1-4 is Block Diagram of the System Unit.

12

Figure 1-4 System Unit Block Diagram

Satellite/E200/E205 Maintenance Manual

1.2 System Unit Components 1 Hardware Overview

The system unit of the computer consists of the following components:

 Processor: Mobile Intel Arrandale Processor.

 Intel Core I5 Processor (FSB, 1066MHz)

 Core Speed: 2.40 GHz

 System Bus: 1066 MHz

 On-Die Level 2 Cache: 3 MB

 Intel Core I3 Processor (FSB, 1066MHz)

 Core Speed: 2.13/2.26 GHz

 System Bus: 1066 MHz

 On-Die Level 2 Cache: 3 MB

 Memory: Two expansion memory slots are provided. They can hold 1.0/2.0/4.0GB memory modules available as options to grow up to 8.0GB.

 PC3-8500 (1066MHz) DDR3 SDRAM supported

 1024/2048/4096MB modules supported

 1024 MB (128M x 64)

 2048 MB (256M x 64)

 4096 MB (512M x 64)

 DDR3 1.5 volt operation

 No parity bit

 64-bit data transfer

 BIOS ROM (Flash EEPROM)

 12Mb x 1 chip (1536KB flash parts)

 NvStorage Size : 64K

 NvStorage Free Space : 63K

 FV00 Size : 992K

 FV00 Free Space : 127K

 FV01 Size : 384K

 FV01 Free Space : 85K

 System Controller

Mobile Intel 5 Series Chipset HM55 / HM57 PCH

 Direct Media Interface (DMI)

 PCI Express Interface

Satellite/E200/E205 Maintenance Manual 13

1 Hardware Overview 1.2 System Unit Components

 Integrated Serial ATA (SATA) Host Controller

 Intel High Definition Audio Controller

 Simple Serial Transport (SST) 1.0 Bus

 Platform Environmental Control Interface (PECI)

 Universal Serial Bus (USB) Controller

 Integrated Gigabit LAN Controller

 Intel Active Management Technology with System Defense

 Intel I/O Virtualization (VT-d) Support

 Intel Trusted Execution Technology Support

 Power Management Logic

 External Glue Integration

 Enhanced DMA Controller

 System Management Bus

 High Precision Event Timers

 Timers Based on 82C54

 Real-Time Clock

 System TCO Reduction Circuits

 Serial Peripheral Interface (SPI) Support

 Interrupt Controller

 Firmware Hub Interface Support

 Low Pin Count (LPC) I/F

 GPIO

 Analog and Digit Display Ports

 JTAG Boundary Scan Support

 Audio Controller

Realtek ALC272 integrated audio controller supports multimedia. The sound system features contain the following:

 2 Stereo DACs support 16/20/24-bit PCM format for stereo audio playback

 2 stereo ADCs support 16/20-bit PCM format for two stereo independent sound inputs

 16/20/24-bit S/PDIF-OUT supports 44.1K/48K/88.2K/96K/192KHz sample rate

 All ADCs support 44.1K/48K/96KHZ sample rate

 4 GPIOs (GPIO0/GPIO3 are digital GPIO shared with digital MIC interface,

GPIO1/GPIO2 are analog) for customized applications

High quality analog differential CD input

 2 jack detection pins each designed to detect up to 4 jacks

 Supports hardware digital volume control for digital microphone input

 Supports external PCBEEP input and built-in digital BEEP generator

14 Satellite/E200/E205 Maintenance Manual

1.2 System Unit Components 1 Hardware Overview

 KBC/EC (Keyboard Controller/Embedded Controller)

A KBC WINBOND WPCE781L chip is used to serve as KBC/EC and Super IO:

 KBC

 Scan controller function

 Interface controller function

 EC

 Power supply sequence control

 Overheat shutdown support

 LED control

 Beep control

 Device ON/OFF

 Cooling fan speed control

 Universal I/O port

 Battery capacity check

 Flash memory reprogramming function

 EC access interface

 I2C communication control

 Battery EEPROM

 24C02 equivalent (128 words x 16 bits, I2C interface) integrated in battery pack

 Storing records of battery use

 Clock Generator

 ICS ICS9LRS3197

 Generating the clock signal required for the system

 LAN Controller

Atheros AR8152-AL1 - 10/100Mbit

 IEEE802.3 10BASE-T/100BASE-TX physical layer interface

 IEEE 802.3u Auto-Negotiation support

 Digital Adaptive Equalization control

 10BASE-T auto-polarity correction

 LAN Connect interface

 Automatic detection of “unplugged mode”

 Remote boot (PXE 2.1)

 Smart power down when link is not detected

Satellite/E200/E205 Maintenance Manual 15

1 Hardware Overview 1.2 System Unit Components

 Wireless LAN Controller

 Support following 3 kinds of mini PCI wireless LAN cards

 IEEE 802.11bg

 IEEE 802.11ag

 IEEE 802.11agn

 Data Rate

 IEEE 802.11bg: Standard 54M bps

 IEEE 802.11ag: Standard 54M bps

 IEEE 802.11agn: Standard 130M bps

 Frequency Channel

 IEEE802.11bg: 2.4GHz

 IEEE802.11ag: 2.4GHz / 5.4GHz

 IEEE802.11agn: 2.4GHz / 5.4GHz

16 Satellite/E200/E205 Maintenance Manual

1.3 2.5-inch HDD 1 Hardware Overview

1.3 2.5-inch HDD

The computer contains an extremely low-profile, lightweight and high-performance HDD.

The HDD incorporates 9.5 mm height magnetic disk and mini-Winchester type magnetic heads. The HDD interface conforms to Serial ATA. Storage capacities supported are 160,

250, 320, 400 & 500GB.

The HDD is shown in Figure 1-5 and some of its specifications are listed in Table 1-1.

Figure 1-5 SATA HDD

Table 1-1 HDD Specifications

Item Specifications

Capacity (GB)

160 GB 250 GB 320 GB

Rotational Speed (RPM)

5400 rpm 5400 rpm 5400 rpm

Height

User Data Sectors

Bytes / Sector

9.5 mm 9.5 mm 9.5 mm

312,581,808 488,397,168 625,142,448

512 512 512

Capacity (GB)

Rotational Speed (RPM)

Height

Item Specifications

User Data Sectors

Bytes / Sector

400 GB

5400 rpm

500 GB

5400 rpm

9.5 mm 9.5 mm

781,422,768 976,773,168

512 512

Satellite/E200/E205 Maintenance Manual 17

1 Hardware Overview 1.4 DVD Super Multi (+-R Double Layer)

1.4 DVD Super Multi (+-R Double Layer)

The DVD Super Multi drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. At maximum, the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and write CD-R at 24x speed, CD-RW at 4x speed, US CD-RW at 24x speed, High Speed CD-

RW at 10x speed, DVD-R at 8x speed, DVD-RW at 6x speed, DVD+R at 8x speed, DVD+R

(Double Layer) at 4x speed, DVD-R (Double Layer) at 4x speed, DVD+RW at 8x speed and

DVD-RAM at 5x speed.

DVD Super Multi Drive is shown in Figure 1-6 and its specifications are listed in Table 1-2.

Figure 1-6 DVD Super Multi Drive

Table 1-2 DVD Super Multi Drive Specifications

Item DVD-ROM mode

Data Transfer Rate

(Mbytes/s)

33.3 (U-DMA transfer mode 2)

16.7 (PIO mode 4, Multiword DMA mode 2)

Access Time (ms)

Average Random

Access

130 ms

CD-ROM mode

130 ms

Data Buffer Size

(Mbytes)

Formats Supported

2MB

DVD:

DVD-VIDEO, DVD-ROM, DVD-R, DVD-RW, DVD-RAM,

DVD+R, DVD+-R (Double Layer), DVD+RW.

CD:

CD-DA, CD-ROM, CD-R, CD-RW, CD-ROMXA, Photo CD (Multi-

Session), Video CD, CD-Extra (CD+), CD-Text.

18 Satellite/E200/E205 Maintenance Manual

1.5 Power Supply 1 Hardware Overview

1.5 Power Supply

The power supply unit provides many different voltages for the system board and performs the following functions:

1. Power input monitor

 Checks whether the DC power supply (AC adapter) is connected to the computer.

 Checks whether the battery pack is connected to the computer.

Monitors the DC power supply input voltage (AC Adapter output voltage).

2. Power supply's internal control

 Turns on and off the battery pack charging power supply.

 Issues a charging current instruction to the PWM control IC of the battery pack charging power supply.

 Controls the supply of DC power supply input (AC Adapter output) to the power supply unit.

 Controls the supply of power to the system block (load/logic circuit side).

 Controls forced shutdown if the power supply malfunctions.

3. Logic circuit control

 Instructs the gate array to enable/disable tuning the power on.

 Controls power-on/off operation.

4. Status display

 Turns on the Power LED (in White).

Battery indicator (in White or Umber or Umber Flash).

5. External interface

 Performs communication through the I2C bus (via the internal EC/KBC).

 Transfers the power supply operation mode.

6. Output monitor

 Monitors the voltage output to the system block (load/logic circuit side).

Monitors the voltage, over voltage, input/output current of the battery pack.

 Monitors the internal temperature of the battery pack.

 Monitors the supply voltage from the AC adapter.

Satellite/E200/E205 Maintenance Manual 19

1 Hardware Overview

1.6 Batteries

The computer has the following 3 types of batteries:

 Main Battery Pack

 Real Time Clock (RTC) Battery

Table 1-3 lists the specifications of these batteries.

Table 1-3 Battery Specifications

1.6 Batteries

Battery Type

Main Battery Pack

6 Cell

Material

Lithium Ion

Output voltage

10.8 V

Capacity

5600 mAh

5800 mAh

RTC Battery

Lithium Ion 3.0 V 14 mAh

1.6.1 Main Battery

The main battery pack serves as the computer's main power source when the AC adapter is not attached. The main battery maintains the state of the computer so that it can resume it.

1.6.2 Battery Charging Control

Battery charging is controlled by TI BQ24721C. When AC adapter and battery pack are attached to the computer, the BQ24721C controls the charge on/off state and detects a full charge.

 Battery Charge

When the AC adapter is attached, the battery is charged by off-state charge when the system is powered off or by on-state charge when it is powered on.

20 Satellite/E200/E205 Maintenance Manual

1.6 Batteries

Table 1-4 Quick/Normal Charging Time

1 Hardware Overview

Off-State Charge

On-State Charge

6 Cell

6 Cell

About 4 hours max

About 4~10 hours max

NOTE: The time required for normal charge depends on the power consumption by the system. Using the fluorescent lamp and frequently accessing the disk consume much power and lengthen the charge time.

Any of the following cases stops battery charge:

1. The battery becomes fully charged.

2. The AC adapter or battery pack is removed.

3. The battery or AC adapter voltage is abnormal.

 Detection of full charge

A full charge is detected only when the battery is being charged by quick or normal charge. A full charge is detected when either of the following conditions is met:

1. The current in the battery charging circuit drops below the predetermined value.

2. The charging time exceeds the fixed limit.

1.6.3 RTC Battery

The RTC battery provides power to keep the current date, time and other system information in memory while the computer is turned off.

Satellite/E200/E205 Maintenance Manual 21

2 概要

Chapter 2

Troubleshooting

2-i Satellite/E200/E205 Maintenance Manual

2 Troubleshooting

Chapter 2 Contents

2.1 Outline.................................................................................................................... 2-1

Procedure 1 Power Icon Check....................................................................... 2-6

Procedure 2 Connection Check....................................................................... 2-8

Procedure 3 Replacement Check .................................................................... 2-8

Procedure 1 Message Check ........................................................................... 2-9

Procedure 2 Test Program Check ................................................................. 2-10

Procedure 3 Replacement Check .................................................................. 2-10

2.5 HDD ..................................................................................................................... 2-11

Procedure 1 Message Check ......................................................................... 2-11

Procedure 2 Partition Check ......................................................................... 2-11

Procedure 3 Format Check............................................................................ 2-12

Procedure 4 Test Program Check ................................................................. 2-13

Procedure 5 Connector Check and Replacement Check............................... 2-14

2.6 Keyboard .............................................................................................................. 2-15

Procedure 1 Test Program Check ................................................................. 2-15

Procedure 2 Connector Check and Replacement Check............................... 2-15

2.7 Display ................................................................................................................. 2-16

Procedure 1 External Monitor Check ........................................................... 2-16

Procedure 2 Test Program Check ................................................................. 2-16

2.8

Procedure 3 Connector Check and Replacement Check............................... 2-16

ODD (Optical Disk Drive) ................................................................................... 2-18

Procedure 1 ODD Cleaning Check............................................................... 2-18

Procedure 2 Test Program Check ................................................................. 2-18

Procedure 3 Connector Check and Replacement Check............................... 2-18

2.9 LAN...................................................................................................................... 2-20

Procedure 1 Test Program Check ................................................................. 2-20

Procedure 2 Connector Check and Replacement Check............................... 2-20

2-ii Satellite/E200/E205 Maintenance Manual

Procedure 1 Test Program Check ................................................................. 2-21

Procedure 2 Connector Check ...................................................................... 2-21

Procedure 1 Test Program Check ................................................................. 2-22

Procedure 2 Connector Check and Replacement Check............................... 2-22

2.12 IEEE 1394 Test .................................................................................................... 2-23

Procedure 1 Test Program Check ................................................................. 2-23

Procedure 2 Connector Check ...................................................................... 2-23

Procedure 1 Test Program Check ................................................................. 2-24

Procedure 2 Connector Check and Replacement Check............................... 2-24

Satellite/E200/E205 Maintenance Manual 2-iii

2 Troubleshooting

Figures

Figure 2-1 Basic Flowchart ............................................................................................. 2-3

Tables

Table 2-1 HDD Error Code and Status ........................................................................ 2-13

2-iv Satellite/E200/E205 Maintenance Manual

2.1 Outline 2 Troubleshooting

2.1 Outline

This chapter describes the fault diagnosis procedures for field replaceable units (FRUs) in the computer.

The FRUs covered here are as follows:

1. System board

4. Display

2. HDD

5. ODD drive

3. Keyboard

6. LAN

7. Finger Print 8. Speaker 9. IEEE 1394

10. Cooling module

See Chapter 4 for the procedures to replace FRUs and Chapter 3 for the procedures to use test programs.

The following tools are required to perform the diagnostic procedures:

1. Diagnostics (maintenance test program) disk

2. Phillips screwdrivers (2 mm, 2.5 mm)

3. Cleaning disk kit (for ODD drive cleaning)

4. Bootable CD

5. Multi-meter

6. External monitor

7. Headphone

8. Microphone

9. A-BEX TEST DVD

10. Music CD

11. DVD TSD-1 (TOSHIBA EMI DVD Test Media)

Satellite/E200/E205 Maintenance Manual 2-1

2 Troubleshooting 2.2 Basic Flowchart

2.2 Basic Flowchart

The basic flowchart in Figure 2-1 serves as a guide for identifying a possibly faulty FRU.

Before going through the diagnostic flowchart steps, verify the following:

 Ask the user if a password has been registered and, if so, ask him or her to enter the password. If the user has forgotten the system password, use a jump wire to make a short circuit on M/B B500 location, then turn the computer power on. When booted, the computer overrides password protection and automatically erases the current password.

 Make sure the Windows® 7 Home Edition has been installed on the HDD. Any other operating system can cause the computer to malfunction.

Make sure any piece of optional equipment has been installed.

2-2 Satellite/E200/E205 Maintenance Manual

2.2 Basic Flowchart

Star t

Connect the AC Adapter

2 Troubleshooting

DC IN LED on ??

Yes

BATTERY LED on ??

Yes

Turn the power on.

No

No

Follow the power supply diagnostic procedure in Section 2.3

Follow the power supply diagnostic procedure in Section 2.3

Any error message displayed ??

No

Message "In Touch with

Tomorrow Toshiba" displayed

Yes

Follow the system board diagnostic procedure in Section 2.4

No

Follow the display diagnostic procedure in Section 2.7

Yes

"Password=" displayed ??

Yes

See the previous page to delete the password.

No

OS started ??

Follow the HDD diagnostic procedure in Section 2.5

No

1

Yes

Figure 2-1 Basic Flowchart (1/2)

Satellite/E200/E205 Maintenance Manual 2-3

2 Troubleshooting 2.2 Basic Flowchart

1

Keyboard works well ??

Insert Bootable CD into ODD

Diagnostic Program

Loaded ??

Yes

Perform each test with the diagnostic program.

diagnostic program ??

Any error detected by the

No

No

Yes

Follow the keyboard diagnostic procedure in Section 2.6

Follow the ODD diagnostic procedure in Section 2.8

Identify the test resulting in the error and perform the appropriate diagnostic procedures

No

Perform the continuous test to check if the error is intermittent.

Any error detected by the diagnostic program ??

END

No

The system is normal.

Yes

Figure 2-1 Basic Flowchart (2/2)

Identify the test resulting in the error and perform the appropriate diagnostic procedures

2-4 Satellite/E200/E205 Maintenance Manual

2.2 Basic Flowchart 2 Troubleshooting

If the diagnostic program cannot detect an error, the error may be intermittent. Run the continuous test program repeatedly to isolate the problem. Check the log utilities function to confirm which diagnostic test detected the error, then perform the appropriate troubleshooting procedures as follows:

1. If an error is detected by the System test, Memory test, Async test, Printer test,

Sound test, or Real Timer test, follow the system board troubleshooting procedures in

Section 2.4.

2. If an error is detected by the Hard Disk test, follow the HDD troubleshooting procedures in Section 2.5.

3. If an error is detected by the Keyboard test, follow the keyboard troubleshooting procedures in Section 2.6.

4. If an error is detected by the Display test, follow the display troubleshooting procedures in Section 2.7.

5. If an error is detected by the ODD test, follow the ODD troubleshooting procedures in

Section 2.8.

6. If an error is detected by the LAN test, follow the LAN troubleshooting procedures in section 2.9.

7. If an error is detected by the Finger Print test, follow the Finger Print troubleshooting procedures in section 2.10.

8. If an error is detected by the Speaker test, follow the Speaker troubleshooting procedures in section 2.11.

9. If an error is detected by the IEEE 1394 test, follow the IEEE 1394 troubleshooting procedures in section 2.12.

10. If an error is detected by the Fan On/Off test, follow the cooling module troubleshooting procedures in Section 2.13.

Satellite/E200/E205 Maintenance Manual 2-5

2 Troubleshooting 2.3 Power Supply

2.3 Power Supply

The power supply in the computer controls many functions and components. To check if the power supply is defective or malfunctioning, follow the troubleshooting procedures below as instructed.

Procedure 1 Power Icon Check

Procedure 2 Connection Check

Procedure 3 Replacement Check

Procedure 1 Power Icon Check

The following two power LEDs indicate the power supply status:

 Battery LED

 DC IN LED

The power supply controller displays the power supply status through the Battery and DC IN

LEDs as in the tables below.

 Battery LED

Battery LED

On in Umber

On in White

Blinking in Umber

(at equal intervals)

Battery being charged

Power supply status

Battery fully charged, with AC adapter connected

Battery low while driving the computer

Off Else

2-6 Satellite/E200/E205 Maintenance Manual

2.3 Power Supply 2 Troubleshooting

 DC IN LED

DC IN LED Power supply status

On in White DC power being supplied (from the AC adapter)

Off Battery damage and can’t charge during DC-in.

Off Else

If the DC IN LED off, follow the steps below:

1. Remove the battery pack and the AC adapter to shut off power supply to the computer.

2. Attach the battery and AC adapter back again.

If the LED still off, follows the steps below:

Check 1 Make sure the DC IN LED goes on in White. If it does not, go to Procedure 2.

Check 2 Make sure the Battery LED goes on in Umber or White. If it does not, go to

Procedure 3.

Satellite/E200/E205 Maintenance Manual 2-7

2 Troubleshooting 2.3 Power Supply

Procedure 2 Connection Check

Power is supplied to the system board as illustrated below:

AC adaptor

System board

AC power cord

AC adaptor cord

Battery pack

Follow the steps below to check whether each connector has been connected correctly:

Check 1 Make sure the AC adaptor and AC power cord have been firmly plugged into the DC IN socket and wall outlet, respectively. When they have been connected correctly, perform Check 2.

Check 2 Connect a new AC adaptor and AC power cord.

If the DC IN LED does not go on, go to Procedure 3.

 If the battery LED does not go on, perform Check 3.

Check 3 Make sure the battery pack has been correctly installed in the computer.

If the battery LED does not go on while the battery pack has been installed correctly, go to Procedure 3.

Procedure 3 Replacement Check

The system board, power supply board, or CPU may be faulty. Disassemble the computer according to Chapter 4 and follow the steps below:

Check 1 Replace the power supply board with a new one. If the battery pack is still not working properly, perform Check 2.

Check 2 Replace the system board with a new one. If the battery pack is still not working properly, perform Check 3.

Check 3 Replace the CPU with a new one.

2-8 Satellite/E200/E205 Maintenance Manual

2.4 System Board 2 Troubleshooting

2.4 System Board

To check if the system board is defective or malfunctioning, follow the troubleshooting procedures below as instructed.

Procedure 1 Message Check

Procedure 2 Test Program Check

Procedure 3 Replacement Check

Procedure 1 Message Check

When the power is turned on, the system performs the self-diagnostic Power On Self Test

(POST) embedded in the BIOS ROM. The POST tests and initializes each IC on the system board.

 If an error message appears on the display, perform Check 1.

 If there is no error message, go to Procedure 2.

 If FREE-DOS or Windows 7 Home Edition is loaded normally, go to Procedure 3.

Check 1 If the following error message is displayed on the screen, press the F1 key as prompted. These errors occur when the system configuration preserved in the RTC memory (generally called CMOS memory) does not match the actual configuration or when the data is lost.

If you press the F1 key as prompted by the message, the TSETUP screen appears to set the system configuration. If the error message appears frequently when the power is turned on, replace the RTC battery. If any other error message is displayed, perform Check 2.

*** Bad RTC battery ***

Check system. Then press [F1] key

Check 2 If the following error message is displayed on the screen, press any key as prompted by the message.

The error message appears when either data stored in RAM to be resumed is lost because the battery has been exhausted or the system board is faulty.

*** Resume failure and press any key to continue ***

Satellite/E200/E205 Maintenance Manual 2-9

2 Troubleshooting 2.4 System Board

Procedure 2 Test Program Check

The maintenance test program contains several programs for diagnosing the system board and CPU. Execute the following test programs using the procedures described in Chapter 3.

1. System test

2. Memory test

3. Keyboard test

4. Display test

5. Hard Disk test

6. Mouse test

7. ODD test

8. Sound test

9. LAN test

If an error is detected during these tests, go to Procedure 3.

Procedure 3 Replacement Check

The system board, memory, or CPU may be defective. Disassemble the computer following the steps described in Chapter 4 and replace the system board, memory module or CPU with a new one.

2-10 Satellite/E200/E205 Maintenance Manual

2.5 HDD 2 Troubleshooting

2.5 HDD

To check if the 9.5mm or 12.5mm HDD is defective or malfunctioning, follow the troubleshooting procedures below as instructed.

Procedure 1 Message Check

Procedure 2 Partition Check

Procedure 3 Format Check

Procedure 4 Test Program Check

Procedure 5 Connector Check and Replacement Check

CAUTION: The contents of the HDD will be erased when the HDD diagnostic test or formatting is executed. Save the required contents of the HDD to floppy disks or other storage drive in advance.

Procedure 1 Message Check

When the computer's HDD does not function properly, some of the following error messages may appear on the display. Follow the steps below to check the HDD.

Check 1 If either of the following messages appears, go to Procedure 2. If the following messages do not appear, perform Check 2.

Insert system disk in drive

Press any key when ready ..... or

Non-System disk or disk error

Replace and press any key

Check 2 Check SETUP to see if the Hard Disk option has been set to “Not used”. If so, choose another setting and restart the computer. If the problem persists, go to Procedure 2.

Procedure 2 Partition Check

Boot from the DOS system. Perform the following checks:

Check 1 Type C: and press the Enter key. If you cannot change to drive C, perform Check 2. If you can change to drive C, perform Check 3.

Check 2 Type FDISK and press the Enter key. Choose “Display partition information” from the FDISK menu. If drive C is listed, perform Check 3.

If drive C is not listed, return to the FDISK menu and choose the option to

Satellite/E200/E205 Maintenance Manual 2-11

2 Troubleshooting 2.5 HDD

create a DOS partition on drive C. Then restart the computer.. If the problem persists, go to Procedure 3.

Check 3 If drive C is listed as active in the FDISK menu, perform Check 4. If drive

C is not listed as active, return to the FDISK menu and choose the option to set the active partition for drive C. Then restart the computer. If the problem persists, perform Check 4.

Check 4 Enter DIR C: and press the Enter key. If the following message is displayed, go to Procedure 3. If contents of drive C are listed on the display, perform Check 5.

Invalid media type reading drive C

Abort, Retry, Fail?

Check 5 Use the SYS command in the DOS system to install system files.

If the following message appears on the display, the system files have been transferred to the HDD. Restart the computer. If the problem persists, go to Procedure 3.

System transferred

NOTE: If the computer is running Windows 7 Home edition and the hard disk capacity is more than 512 MB, the FDISK program will ask if you need support for a partition larger than 2 GB. Select Y for large partition support; however, be sure to read the precaution regarding access by other operating systems.

Procedure 3 Format Check

The 2.5-inch HDD is formatted using the low-level format program and the FREE-DOS

FORMAT program. Using these programs, follow the steps below to format the HDD.

Check 1 Enter FORMAT C:/S/U to format the HDD and transfer system files. If the following message appears on the display, the HDD has been formatted.

Format complete

If you cannot format the HDD using the test program, go to Procedure 4.

2-12 Satellite/E200/E205 Maintenance Manual

2.5 HDD 2 Troubleshooting

Procedure 4 Test Program Check

Run the HDD test program stored on the maintenance test program disk for all test items.

See Chapter 3 for details on how to use the test program.

If an error is detected during the HDD test, an error code and status will be displayed. The error codes and their status names are listed in Table 2-1. If an error code is not generated and the problem still exists, go to Procedure 5.

Table 2- 1 HDD Error Code and Status

Code Status

1

2

3

4

Get Parameter Fail !

Read Old Data Error

Write Pattern Error

Read Back Data Error

5

6

Data Compare Error

Restore Data Error

7

9

Read Verify Error

Seek Error

10 Disk Controller Self Test Failed

11 Disk Controller Test unexpected interrupt Failed

12 Disk Controller action Test Failed

13 Disk dos not support SMART

14

15

Disk read attribute threshold error

Disk read attribute value error

16 Disk SMART attribute value error

Satellite/E200/E205 Maintenance Manual 2-13

2 Troubleshooting 2.5 HDD

Procedure 5 Connector Check and Replacement Check

The HDD or system board may be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks:

Check 1 Make sure the following connectors have been firmly connected to the

HDD, system board and CPU.

HDD

System board

CPU

If any connector is loose or off, reconnect it firmly and return to Procedure 1.

If there is still an error, perform Check 2.

Check 2 The HDD may be damaged. Replace it with a new one following the disassembling instructions in Chapter 4. If the problem persists, perform

Check 3.

Check 3 The System board may be damaged. Replace it with a new one following the disassembling instructions in Chapter 4. If the problem persists, perform Check 4.

Check 4 The CPU may be damaged. Replace it with a new one following the disassembling instructions in Chapter 4.

2-14 Satellite/E200/E205 Maintenance Manual

2.6 Keyboard 2 Troubleshooting

2.6 Keyboard

To check if the computer’s keyboard is defective or malfunctioning, follow the troubleshooting procedures below as instructed.

Procedure 1 Test Program Check

Procedure 2 Connector Check and Replacement Check

Procedure 1 Test Program Check

Execute the Keyboard test available as part of the maintenance test program. See Chapter 3 for information on how to perform the test.

If an error is detected in the test, go to Procedure 2. If no error is detected, the keyboard itself is normal.

Procedure 2 Connector Check and Replacement Check

The keyboard or system board may be disconnected or faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks:

Check 1 Make sure the keyboard cable has been firmly connected to the system board.

Check 2

Keyboard

System board

CPU

If the cable is loose or off, reconnect it firmly and return to Procedure 1.

If there is still an error, perform Check 2.

The keyboard may be faulty. Replace it with a new one following the instructions in Chapter 4. If the problem persists, perform Check 3.

Check 3

Check 4

The System board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the keyboard is still not functioning properly, perform Check 4.

The memory may be defective. Replace the memory module with a new one

following the steps described in Chapter 4. If the problem persist,

perform Check 5.

Check 5 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.

Satellite/E200/E205 Maintenance Manual 2-15

2 Troubleshooting 2.8 Display

2.7 Display

To check if the computer’s display is defective or malfunctioning, follow the troubleshooting procedures below as instructed.

Procedure 1 External Monitor Check

Procedure 2 Test Program Check

Procedure 3 Connector Check and Replacement Check

Procedure 1 External Monitor Check

Connect an external monitor to the computer's external monitor port, then boot the computer.

The computer automatically detects the external monitor even if resume mode is enabled.

If the external monitor works correctly, the internal LCD, LCD/FL cable, or FL may be faulty. Go to Procedure 3.

If the external monitor appears to have the same problem as the internal monitor, the system board may be faulty. Go to Procedure 2.

Procedure 2 Test Program Check

Insert the diagnostics bootable CD in the computer's CD ROM, turn on the computer and run the test. See Chapter 3 for information on how to perform the test.

If an error is detected in the test, go to Procedure 3. If no error is detected, the display itself is normal.

Procedure 3 Connector Check and Replacement Check

The display unit has an LCD module, Fluorescent lamp (FL), panel close switch and FL inverter board. Any of the components or their connections may be defective. Disassemble the computer following the steps described in Chapter 4, then perform the following checks:

(1) If the FL does not light, perform Check 1.

(2) If characters or graphics are not displayed normally, perform Check 5.

(3) If the FL remains lit when the display is closed, the panel close switch may be defective. Perform Check 8.

Check 1 Make sure the following cables have been firmly connected to the system board and FL inverter board.

FL

FL inverter board

System board

CPU

HV cable LCD/FL cable

If any of the cables is loose or off, reconnect it firmly and return to

Procedure 3. If there is still an error, perform Check 2.

Check 2 The LCD/FL cable may be faulty. Replace it with a new one and return to

Procedure 3. If there is still an error, perform Check 3.

2-16 Satellite/E200/E205 Maintenance Manual

2.8 Display 2 Troubleshooting

Check 3

Check 4

Check 5

The FL may be faulty. Replace it with a new one and return to Procedure

3. If there is still an error, perform Check 4.

The FL inverter board may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 5.

Make sure the LCD/FL cable has been firmly connected to the system board and LCD module.

FL inverter board

System board

CPU

LCD/FL cable

Check 6

Check 7

Check 8

If the cable is loose or off, reconnect it firmly and return to Procedure 3.

If there is still an error, perform Check 6.

The LCD/FL inverter cable may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 7.

The LCD module may be faulty. Replace it with a new one and return to

Procedure 3. If there is still an error, perform Check 8.

The System board may be faulty. Replace it with a new one. If there is

Check 9 still an error, perform Check 9.

The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persists, perform Check 10.

Check 10 The CPU may be faulty. Replace it with a new one following the instructions in Chapter 4.

Satellite/E200/E205 Maintenance Manual 2-17

2 Troubleshooting 2.9 ODD (Optical Disk Drive)

2.8 ODD (Optical Disk Drive)

To check if the internal ODD drive is defective or malfunctioning, follow the troubleshooting procedures below as instructed.

Procedure 1 ODD Cleaning Check

Procedure 2 Test Program Check

Procedure 3 Connector Check and Replacement Check

Procedure 1 ODD Cleaning Check

1. Turn off the power to the computer.

2. Open the ODD tray by inserting a slender object such as a straightened paper clip into the eject hole. The object must be long enough to activate the eject mechanism.

3. Clean the laser pickup lens with a lens cleaner. Apply the cleaner to a cloth and wipe the lens.

4. If the ODD drive still does not function properly after cleaning, go to Procedure 2.

Procedure 2 Test Program Check

Execute the ODD drive test program available as part of the maintenance test program. Insert the diagnostics CD in the computer's CD, turn on the computer and run the test. Then insert a test ODD (Toshiba-EMI DVD-ROM TEST DISK TSD-1) into the ODD drive. See Chapter 3 for information on how to perform the test.

If any error is detected by the test, go to Procedure 3.

Procedure 3 Connector Check and Replacement Check

The ODD drive is connected to the system board by the connector. The connector may be disconnected from the system board or faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks:

Check 1 Make sure the following connector has been firmly connected to the ODD drive and the system board.

ODD

drive

System board

CPU

Attachment case

Connector

If the connector is loose or off, reconnect it firmly and return to Procedure 2.

If there is still an error, perform Check 2.

Check 2 The connector may be faulty. Replace the connector with a new one following the steps in Chapter 4. If the ODD drive is still not functioning properly, perform Check 3.

2-18 Satellite/E200/E205 Maintenance Manual

2.10 LAN 2 Troubleshooting

Check 3

Check 4

Check 5

The ODD drive may be faulty. Replace the ODD drive with a new one following the steps in Chapter 4. If the ODD drive is still not functioning properly, perform Check 4.

The system board may be faulty. Replace it with new one following the instructions in Chapter 4. If the ODD drive is still not functioning properly, perform Check 5.

The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4.

Satellite/E200/E205 Maintenance Manual 2-19

2 Troubleshooting 2.9 ODD (Optical Disk Drive)

2.9 LAN

To check if the computer’s LAN is defective or malfunctioning, follow the troubleshooting procedures below as instructed.

Procedure 1 Test Program Check

Procedure 2 Connector Check and Replacement Check

Procedure 1 Test Program Check

Execute the LAN check program available as part of the maintenance test program. This program will check the LAN. Insert the Bootable CD into the CD. Turn on the computer and run the check program. See Chapter 3 for information on how to perform the check.

If any abnormal is detected by the check, go to Procedure 2

Procedure 2 Connector Check and Replacement Check

The LAN connector (RJ45) is mounted on the system board. If the LAN malfunctions, the system board or CPU might be faulty.

Disassemble the computer following the steps described in Chapter 4 and perform the following checks:

Check 1 The system board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the LAN is still not functioning properly, perform Check 2.

Check 2 The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persists, perform

Check 3.

Check 3 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.

2-20 Satellite/E200/E205 Maintenance Manual

Finger Print (Optional)2.10 Audio Test

2 Troubleshooting

2.10 Finger Print (Optional)

To check if the computer’s Finger Print is defective or malfunctioning, follow the troubleshooting procedures below as instructed.

Procedure 1 Test Program Check

Procedure 2 Connector Check

Procedure 1 Test Program Check

Execute the Finger Print test program available as part of the maintenance test program. This program checks the Finger Print. Insert the Bootable CD into the CD. Turn on the computer and run the test. See Chapter 3 for information on how to perform the test.

If any error is detected by the test, go to Procedure 2

Procedure 2 Connector Check

The Finger Print connector is mounted on the system board. If the Finger Print malfunctions, the system board or Finger Print Board might be faulty.

Disassemble the computer following the steps described in Chapter 4 and perform the following checks:

Check 1 The Finger Print board may be faulty. Replace it with a new one following the instructions in Chapter 4. Then go through procedure 1 again. If the Finger Print is still not functioning properly, perform Check

Check 2

2.

The system board may be defective. Replace the system board with a new one following the steps described in Chapter 4. Then go through procedure 1 again.

Satellite/E200/E205 Maintenance Manual 2-21

2 Troubleshooting 2.10 Finger Print

2.11 Audio Test

To check if the computer’s Speaker is defective or malfunctioning, follow the troubleshooting procedures below as instructed.

Procedure 1 Test Program Check

Procedure 2 Connector Check and Replacement Check

Procedure 1 Test Program Check

Execute the Audio test available as part of the maintenance test program. See Chapter 3 for information on how to perform the test.

If an error is detected in the test, go to Procedure 2. If no error is detected, the Audio itself is normal.

Procedure 2 Connector Check and Replacement Check

The Audio or system board may be disconnected or faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks:

Check 1 Make sure the Speaker cable has been firmly connected to the system board.

Speaker

System board

CPU

If the cable is loose or off, reconnect it firmly and return to Procedure 1.

If there is still an error, perform Check 2.

Check 2 The Speaker may be faulty. Replace it with a new one following the instructions in Chapter 4. If the problem persists, perform Check 3.

Check 3 The System board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the Audio is still not functioning properly, perform Check 4.

Check 4 The memory may be defective. Replace the memory module with a new one

following the steps described in Chapter 4. If the problem persist,

perform Check 5.

Check 5 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.

2-22 Satellite/E200/E205 Maintenance Manual

2.12 IEEE 1394 Test 2 Troubleshooting

2.12 IEEE 1394 Test

To check if the computer’s IEEE 1394 is defective or malfunctioning, follow the troubleshooting procedures below as instructed.

Procedure 1 Test Program Check

Procedure 2 Connector Check

Procedure 1 Test Program Check

Execute the IEEE 1394 test program available as part of the maintenance test program. This program checks the IEEE 1394. Insert the Bootable CD into the CD. Turn on the computer and run the test. See Chapter 3 for information on how to perform the test.

If any error is detected by the test, go to Procedure 2

Procedure 2 Connector Check

The IEEE 1394 connector is mounted on the system board. If the IEEE 1394 malfunctions, the system board or CPU might be faulty.

Disassemble the computer following the steps described in Chapter 4 and perform the following checks:

Check 1 The system board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the IEEE 1394 is still not functioning properly, perform Check 2.

Check 2

Check 3

The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persists, perform

Check 3.

The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.

Satellite/E200/E205 Maintenance Manual 2-23

2 Troubleshooting 2.13 Cooling Module

2.13 Cooling Module

To check if the computer’s cooling module is defective or malfunctioning, follow the troubleshooting procedures below as instructed.

Procedure 1 Test Program Check

Procedure 2 Connector Check and Replacement Check

Procedure 1 Test Program Check

Execute the Fan On/off test program available as part of the maintenance test program. This test program checks the cooling module. Insert the diagnostics bootable CD in the computer's CD, turn on the computer and run the test. See Chapter 3 for information on how to perform the test.

If any error is detected by the test, go to Procedure 2.

Procedure 2 Connector Check and Replacement Check

The cooling module is connected to the system board. If the cooling module malfunctions, there may be a bad connection between the cooling module and the system board or either might be faulty.

Disassemble the computer following the steps described in Chapter 4 and perform the following checks:

Check 1 Make sure the cooling module has been firmly connected to the connector on the system board. Also make sure that the tape is not stuck to any part of the fan and that the fan is free of foreign matter.

Cooling module System board

CPU

If the connector is disconnected, connect it firmly to the system board and return to Procedure 1. If the tape is stuck to any part of the fan, stick it back to the specified point. If a foreign matter is found in the fan, remove it and then return to Procedure 1. If there is still an error, perform Check 2.

Check 2 The cooling module may be faulty. Replace it with a new one following the steps in Chapter 4. If the cooling module is still not functioning properly, perform Check 3.

Check 3 The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persists

,

perform Check 4.

Check 4 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.

2-24 Satellite/E200/E205 Maintenance Manual

2.13 Cooling Module

2 Troubleshooting

Satellite/E200/E205 Maintenance Manual 2-25

Chapter 3

Diagnostic Programs

ii

3 Diagnostic Programs

Chapter 3 Contents

3.1

3.2

3.3

3.4

3.5

3.6

General .......................................................................................................................... 1

Quick Start .................................................................................................................... 3

3.2.1

3.2.2

3.2.3

3.2.4

Quick Test ............................................................................................... 3

Customization Test .................................................................................. 3

Keyboard Layout test

Hotkey Test

.............................................................................. 7

............................................................................................. 8

3.2.5

3.2.6

3.2.7

3.2.8

3.2.9

3.2.10

3.2.11

Audio Play Test ....................................................................................... 9

Audio Record Test ................................................................................... 9

DMI Read ................................................................................................ 9

DMI Write

View Logs

............................................................................................. 10

3D Sensor Test ...................................................................................... 11

System Information ............................................................................... 17

............................................................................................. 18

3.2.12 Exit to

Free DOS

.................................................................................. 19

3.2.13 The Diagnostics Screen Explanation ..................................................... 19

Options ........................................................................................................................ 22

Overview ............................................................................................... 22 3.3.1

3.3.2

3.3.3

3.3.4

Batch Parameters Configuration

Item’s Parameters Configuration

Load Batch Parameters

........................................................... 23

........................................................... 25

.......................................................................... 26

3.3.5

3.3.6

3.3.7

Save Batch Parameters

Specify LOG Viewer

.......................................................................... 27

LOG Parameters Setting ........................................................................ 28

............................................................................. 29

3.3.8

3.3.9

Display LOG File .................................................................................. 29

LOG Viewer .......................................................................................... 30

3.3.10 LOG File Sample ................................................................................... 31

Subtests ....................................................................................................................... 33

System Test ................................................................................................................. 36

Memory Test ............................................................................................................... 41

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3 Diagnostic Programs

3.7

3.8

3.9

3.10

3.11

3.12

Storage ........................................................................................................................ 47

Video ........................................................................................................................... 51

Communication (COMM) .......................................................................................... 59

Peripheral .................................................................................................................... 60

Error Codes and description ........................................................................................ 64

Quick Test Item List ...................................................................................................... i

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

iii

3.1 General 3 Diagnostic Programs

3.1 General

This chapter explains the diagnostic programs which tests and diagnoses the functions of the hardware components of this computer. The diagnostic programs can be classified into two types: OPTION and DIAGNOSTIC TEST.

NOTE 1: This Diagnostic supports MainZ 10

NOTE 2: Before test must set SATA Controller Mode to “Compatibility” in BIOS

Advanced setting, when finished test set it to “AHCI”

NOTE 3: Before running a test, be sure to:

1. Check that all the cables are connected securely.

2. Exit the application that is currently running and close Windows.

The OPTION includes the following functions:

Select All Items

Test All Items

Edit Batch Parameters

Load Batch Parameters

Save Batch Parameters

Log Parameters

Specify Log Viewer

Display Error Log File

DOS Shell

Exit to Free-DOS

The DIAGNOSTIC TEST Devices include the following tests:

System Test

Memory Test

Storage Test

Video Test

Communication Test

Peripheral Test

Keyboard Layout Test

Hot Key Test

Audio Play Test

Audio Record Test

3D Sensor Test

DMI Read

DMI Write

System Information

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 1

3 Diagnostic Programs 3.1 General

Before running the diagnostic programs, get the following tools prepared:

A Service Diagnostic BOOT CD or USB Flash Memory

A Formatted FLOPPY DISK

A Test Media CD (A-BEX TEST CD-ROM TCDR-702)(for CD-ROM test)

A Test Media DVD (Toshiba-EMI DVD-ROM TEST DISK TSD-1)

An External Monitor (for DISPLAY test)

A CD-ROM Driver (for CD-ROM test)

Audio Line for audio record test

A Data CD (for CD-ROM test)

The following chapters describe all the test details. The test items could be selected from the

DIAGNOSTIC TEST menu.

Note:

When booting up the unit for the first time, the system will automatically select the location of the result log file. If a USB floppy drive is connected, and there is an unprotected floppy diskette with more then 50KB spare space in the drive, system will save all log files into the root directory the diskette; otherwise, system will save all log files in the root directory of

RAM disk.

2

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.2 Quick Start

3.2 Quick Start

3 Diagnostic Programs

When the system is booting from Service Diagnostic CD or USB Flash Memory, the following screen will be displayed:

Please select a test item or select 0 to exit to

Free-DOS:

3.2.1 Quick Test

When this item is selected, the system will run the configured test items and generate a test report automatically.

When the test is completed, a file named Quick.log would be saved in the defined location.

When Quick.log is being created, meanwhile, a file named quick.log has already existed, the system will automatically rename Quick.log to Quick.old for the backup purpose of the log file.

For the detail of test item, please refer to Quick Test Item List.

3.2.2 Customization Test

When this item is selected, the system will run the diagnostic programs according to the procedures you defined. When the test is completed, a file named Custom.log will be saved in the defined location. Please see the following example-- Mouse test.

1.

Use arrow key to select ‘TouchPad’ item on ‘Peripheral’ in the menu, then press Space key to select it. (When it is being selected, there is a X marked in the

[ ]

)

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 3

3 Diagnostic Programs 3.2 Quick Start

Select ‘Test Mouse’ or press F8 to run the test. The prompt information would be displayed in the screen as below. This test item needs user to verify whether the mouse works normally.

The test result will be displayed in the following screen:

4

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.2 Quick Start 3 Diagnostic Programs

Here is another method to run the test: Highlight a test item by using arrow keys, then, press Enter to start. If there are parameters provided, user should set parameters in the parameter dialog window.

CPU Speed Test (Step by Step):

1.

Select test item:

Select SystemCPUCPU Speed, then, press the Enter key.

2.

Parameters Setting

Choose the OK button after you set the proper parameters in the following window.

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 5

3 Diagnostic Programs 3.2 Quick Start

3.

Test Result

System will automatically run and display the test result as follows:

Following is the comparison report of the two testing methods mentioned above:

1) Configuration and Running

As to the method used in Mouse test, the user is required to select test items by pressing

Space key and set the parameters artificially, (See 3.3.3 Item’s Parameters

Configuration) Then press F8 to start the test. User should configure each parameter in

advance; otherwise the default parameters would be used. Using this method, user is allowed to select more than one test item at one time.

2) Running the current test item

6

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.2 Quick Start 3 Diagnostic Programs

As to the method adopted in CPU Speed test, user should highlight the test item and press Enter to start testing. And the user has to setup the parameters every time before running the test. Using this method, only one test item would be tested at one time.

3.2.3 Keyboard Layout test

The test purpose is to check whether 30 kinds of keyboards run well during the test procedure. When users choose the item, the names of these countries will be displayed on the screen for user choice. User press any index of token in ASCII, and the program will test the kind of keymap of the country.

The test screen would be shown as below:

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 7

3 Diagnostic Programs 3.2 Quick Start

It requires user to press the key and check whether the key in the screen changes color or not. User can terminate test by typing ‘END’. When testing the ‘Fn’ key, it must press the ‘Enter’ key at the same time.

When the user has checked all the keys and all the keys in the screen have changed color, the diagnostics program would automatically end the test and report the pass information.

If keyboard test fails, program will terminate the test and report the fail information when it is time to timeout.

The test will end when all keys are pressed or test time is out after 90 seconds.

3.2.4 Hotkey Test

Check whether Hotkey run well. Hotkey test mainly functional keys, for example: IE

Key Audio play etc. The methods of testing hotkey are different from keyboard tests sometimes depending on the specific type of notebooks, and this explains why some types of notebooks can be tested together with keyboard while others cannot. Press E+

+N+D to quit the test.

8

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.2 Quick Start 3 Diagnostic Programs

3.2.5 Audio Play Test

Check whether the system could playback audio normally. When the test is completed, a file named Audio_P.log will be saved in the defined location.

3.2.6 Audio Record Test

Check whether the system could record the sound normally. If there is no error during the whole test, Pass; otherwise Fail. The test will repeat for four times. When the test is completed, a file named autest.log will be saved in the defined location.

3.2.7 DMI Read

Read the information from the system’s SMBIOS and display it in the screen as follows:

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 9

3 Diagnostic Programs 3.2 Quick Start

User can press any key to exit the program.

3.2.8 DMI Write

In addition to reading the DMI information, DMI Write also permits attributes editing and updating: Manufacture, Product Name, Version, Serial Number, and OEM Part

Number, etc. The following screen will be displayed:

In this screen, there are two lines which attribute could be edited and updated. The 1 st line (the font in yellow with blue background) shows the attribute’s value that is read from the current system and the 2 nd

line (the font in red with turquoise background) shows the same value as that in the 1 st

line before user’s editing. User can modify the

10

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.2 Quick Start 3 Diagnostic Programs

attribute’s value in the 2 nd

line and press Enter to confirm the current edition and continue editing the next attribute.

During the editing, user could press F2 to confirm the DMI attribute update or press F4 to ignore the modification. Press ESC to exit the program of DMI Write.

The confirmation screen is as below:

The attributes that have been modified would be marked in red; otherwise in yellow.

User could press F2 to save the changes, or press F4 to ignore and exit the current program.

3.2.9 3D Sensor Test

In 3D Sensor test, the system checks whether the HDD protection is normal. This program judges by sampling five kinds of data shown below.

No Item Contents

1 Access platform.

An access platform is leveling.

2 Test

Fixture

The Fixture which fixes PC by 90 degree inclination is used.

Vibration/shock doesn't take a PCB at the time of T&D inspection.

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 11

3 Diagnostic Programs 3.2 Quick Start

3 Test1 The display of a test program and the set method of PC are shown below.

Display of a Test Program

The portion which PC and Test-Fixture contact is green.

Set method of PC

Z

Upper

X

Judgment

If all data is less than ranges, it will be OK.

12

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.2 Quick Start 3 Diagnostic Programs

4 Test2 The display of a test program and the set method of PC are shown below.

Display of a Test Program

Set method of PC

Uppe r

Rear

Judgment

If all data is less than ranges, it will be OK.

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 13

3 Diagnostic Programs 3.2 Quick Start

5 Test3 The display of a test program and the set method of PC are shown below.

Display of a Test Program

Set method of PC

Right

Uppe r

Judgment

If all data is less than ranges, it will be OK.

14

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.2 Quick Start 3 Diagnostic Programs

6 Test4 The display of a test program and the set method of PC are shown below.

Display of a Test Program

Set method of PC

Uppe r

Front

Judgment

If all data is less than ranges, it will be OK.

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 15

3 Diagnostic Programs 3.2 Quick Start

7 Test5 The display of a test program and the set method of PC are shown below.

Display of a Test Program

Set method of PC

Uppe r

Left

Judgment

If all data is less than ranges, it will be OK.

8 Inspection Judgment

If all data is less than ranges, it will be OK.

9 Setting

Calibration data

When an inspection result is O.K., calibration at HPC.

If it succeeded, the system will prompt a message of PASS, otherwise the message will be FAIL.The test information will be written in log file.

Note:

Please do not use this program, when you test PC without 3D sensor.

16

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.2 Quick Start 3 Diagnostic Programs

3.2.10 System Information

This function is used to read the system information. When the test is completed, a file named System.log will be saved in the defined location. During the reading process, the following screen will be displayed to indicate that the progress is in detection:

On the left column of the above screen, the detected hardware components are listed. The corresponding information of the detected hardware components is displayed on the right of the screen. It displays the current running status information of the check program.

The name of the program is marked on the top of the screen. At the bottom, the function keys are listed for user operation. During the detection, keyboard operation is invalid.

When the detection is finished, the hardware components information will be displayed as follows:

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 17

3 Diagnostic Programs 3.2 Quick Start

User can use function keys listed on the bottom of the screen to display the configuration of the component or exit the current program. On the left column, the components information is listed and user can use arrow keys or PgUp/PgDn to view the list and highlight the chosen component. On the right column, the configuration information of the highlighted component is listed. Press ESC to exit this program.

3.2.11 View Logs

User can enter one choice to view a log file in the screen as follows.

18

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.2 Quick Start 3 Diagnostic Programs

3.2.12 Exit to

Free DOS

Select this item to exit to

Free DOS.

3.2.13 The Diagnostics Screen Explanation

Below is an example of running a test item. It includes the following parts: Diagnostics

Windows, Test Status Area, Progress Bar, Error List, Test Item’s Title, Status Bar and

Message Box.

1. Diagnostics Windows

When a test item is running, a Diagnostics Windows is displayed in full screen. It consists of the following parts: Title Bar, Test Running Status and Report Panel, Status Bar. There would prompt a message box called USER BREAK in the central of the window whether user press ESC to interrupt the test.

2. Test Running Status and Report Panel

Test Running Status and Report Panel are located on the middle of Diagnostics Windows.

 Test item name, test process and test result are displayed in the left;

Test status and result are displayed in the upper right corner of the screen. It displays the test status of the current test item – TEST (in testing), PASS (test finished and its result is passed), FAIL (test finished and its result is failed) and SKIP (test skipped).

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 19

3 Diagnostic Programs 3.2 Quick Start

 The error list of each test module is displayed at the lower right corner of the screen. It would display the total error quantity found in the test, the most recent five error codes and description would be shown here. Detailed error report could be viewed with

Logview.exe.

 When pressing ESC key during the test process, a User Break Windows will be popped up for the user to select.

3. USER BREAK

Pressing ESC key to interrupt the test, USER BREAK message box would be prompted out in the central of Diagnostics Window for the user to select the following actions:

CONTINUE---- Continue the test;

SKIP---- Stop the sub-item of current test item to go to the next item’s test;

ABORT----Stop the current test item to test the next module.

ABORT ALL---- Stop all the selected test items. User could use the hot key Ctrl+D to achieve the same operation. When the user calls ABORT ALL, the following message box will prompt for his selecting.

4. Title Bar:

Title Bar located at the top of the window, it includes information as follows:

Program Name and Its Version: Service Diagnostic Ver1.10;

Test Module Name: Label the name and version of the test module. For example, in the above screen, the name of the test module is ‘Memory Tester Build Date 200

7.02.09’.

Status Bar: Located at the bottom of the screen as follows:

The status bar is used to indicate the current script setting and test status. It consists of two lines that includes the information as follows:

Test Mode: TIMEBOUND or LOOPBOUND, e.g. LOOPBOUND in the above screen;

20

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.2 Quick Start 3 Diagnostic Programs

Script File Name: Script file name, e.g. ‘

Custom.INI’ in the above screen;

Current Time(C. TIME): Current system time, e.g. ‘C.TIME:2008-0

2-16 00:42:40’ in the above screen;

Test Time Remaining (LEFT): In TIMEBOUND mode, it would display the remaining test time at the same location as Current TIME (C. TIME) in the above screen;

Current Loop Count: In LOOPBOUND mode, it will display the total LOOP number planning to execute and the current LOOP number have been finished, e.g. ‘COUNT:

01/01’ in the above screen;

CPU Temperature: Detect the temperature in the current CPU, e.g. ‘CPU:

56C’ in the above screen;

Remaining Battery Capacity: Remaining Battery Capacity detected in the current

Battery, e.g. ‘BAT:

46%’;

Test Order: Define the test sequence. There is two sequence modes: Sequential Test

Mode and Random Test Mode. The default mode is Sequential Test Mode, it would displays ‘ORDER: SEQ’ as in the above screen;

LOG File Name: Display the file name of the test log, e.g.

Custom.Log in the above screen;

Start Test Time (S.TIME): Display the test start time for the current test item or the test script, e.g. ‘S.TIME: 2008-0

2-16 00:42:28’ in the above screen;

Break On Error: Display ‘HALT’ as shown in the above screen when ‘Break On Error’ is enabled;

Wait On Error: Display ‘WAIT’ as shown in the above screen when ‘Wait On Error’ is enabled;

Pause Enable: Display ‘PAUSE’ when “Pause Enable” is enabled;

Manual Interrupt Method: Display ‘Esc: Break’ to tell the user how to manually interrupt the test process.

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 21

3 Diagnostic Programs

3.3 Options

3.3Option

3.3.1 Overview

In Service Diagnostics, with the Options menu user can configure the batch parameters, test item’s parameters and those parameters created by the LOG file.

Options Menu Notes:

Select All/None Items

Switch between selecting all test items and selecting none. The hot key is F6.

Test Selected Items

Execute all selected test items in this editor. The hot key is F8.

If “Interactive” option in batch parameters has not been selected, a warning message would be shown as below:

Edit Batch Parameters

22

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.3 Option 3 Diagnostic Programs

Configure batch parameters and all the test item’s parameters.

 Load Batch Parameters

Upload all the test items and the parameters to the *.ini file.

Save Batch Parameters

Save all the parameters and the test items that are configured in the editor to a specified file.

Log Parameters

Configure LOG parameters.

Specify LOG Viewer

Specify the viewer for the LOG file.

Display Error Log File

Load the LOG file viewer specified in the Specify Log Viewer to view the LOG file.

DOS Shell

Enter the DOS Shell and execute the DOS programs. You can also exit to the

Service Diagnostics Editor by the command of EXIT.

Exit to DOS

Exit the Service Diagnostics Editor and back to DOS.

3.3.2 Batch Parameters Configuration

The batch parameters configuration screen can be accessed through Service

Diagnostics/OPTIONS -> EDIT BATCH PARAMETERS -> BATCH

PARAMETERS:

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 23

3 Diagnostic Programs 3.3Option

Test Order

Specify the order of the test items. Choose 'Sequence' to adopt the sequential mode; choose 'Random' to run the test items in random sequence.

Test Options

Choose one of the following options:

Wait On Error

Wait for further confirmation while an error occurs.

Break On Error

Stop the test when a test item fails.

Pause Enable

Pause at the end of each test items and wait for the user to response with the test items that requires the user to assist the test processes, such as the keystroke test.

Interactive

If the item is enabled during the test, the test items that need user to response can run normally, such as Mouse test; If it is disabled, those test items will report

FAIL.

When the option here is enabled, it would affect all the test items while the same option in “Item Parameters Configuration” only affect that test item.

Monitor Battery Life

24

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.3 Option 3 Diagnostic Programs

Monitor the remaining battery capacity (percent).

Monitor CPU Thermal

Monitor the CPU temperature.

Test Mode

LOOPBOUND

The chosen test items will run repeatedly according to the times specified in the

'Number of Loops'.

TIMEBOUND

The chosen test items will run for an extent time specified in 'Time Limit Hrs' and

'Time Limit Min'.

Time Limit Hrs

Specify the hours whether 'TIMEBOUND' is chosen under the batch mode.

Time Limit Min

Specify the minutes whether 'TIMEBOUND' is chosen under the batch mode.

Number Of Loops

Specify the repeating times when 'Loop Bound' is chosen under the batch mode.

3.3.3 Item’s Parameters Configuration

The test items’ parameters configuration screen can be accessed through Service

Diagnostics/Options -> Edit Batch Parameters -> Item’s Parameters-> System-

>CPU-> Basic Functionality:

Repeat count

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 25

3 Diagnostic Programs 3.3Option

Repeat times of the test item.

Interactive

If the item is enabled during the test, the test items that need user to response can run normally, such as PS2 Mouse test; If it is disabled, those test items will report FAIL.

Whether the option here is enabled, it only affects the current test item.

Parameters

For the test items with specific parameters, this option will call the related configuration screens. Otherwise, the program will show the following dialogue window:

Parameters for the specific test items:

Some test items (Memory, HDD, e g...) have their individual parameters, which can be configured in their parameters setting window.

3.3.4 Load Batch Parameters

Batch parameter is saved in the script file whose extension name is INI (*.INI).

Below is the screen shot of “Load Batch Parameters”.

26

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.3 Option 3 Diagnostic Programs

In this window, you can specify the .INI files that you wanted to be edited or modified.

3.3.5 Save Batch Parameters

Here you can save the edited or modified content to the batch parameters files.

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 27

3 Diagnostic Programs 3.3Option

3.3.6 LOG Parameters Setting

You can access the Log Parameters screen through Service Diagnostics\Options -

Generate Report.

Report Destination

If selecting 'NONE', no log file will be generated; if selecting 'FILE', a log file with the name specified in 'Log File Name' will be generated.

Log Options

Log Errors

If selecting this parameter, errors will be recorded when the test fails.

Log Test Activities

If selecting this parameter, the subtest results will be recorded.

Log Test Start Time

If selecting this parameter, the start time of the test will be recorded.

Log Test End Time

If selecting this parameter, the end time of the test will be recorded.

Log Errors Only

If selecting this parameter, errors will be recorded only when the test fails.

Log Errors Only with Time

28

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.3 Option 3 Diagnostic Programs

If selecting this parameter, errors and time will be recorded only when the test fails.

Append to Old Log File

If selecting this parameter, the new log will be added to the old one.

Log Device Info on Fail

If selecting this parameter, details of the failed test will be recorded.

Log file Name

Specify the Log file name. You can input the detail path of the file. System will show the detail path of the file.

3.3.7 Specify LOG Viewer

You can specify the Log file viewer in the Specify Log Viewer screen.

The default viewing program of Service Diagnostics is LogView.exe.

3.3.8 Display LOG File

You can specify the Log file for viewing in the Display Error Log File screen.

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 29

3 Diagnostic Programs 3.3Option

In this screen, you can specify a Log file and view it with the viewer designated in

Specify LOG Viewer.

3.3.9 LOG Viewer

Service Diagnostic Log viewer:

↑, ↓

Scroll a line backward or forward on the screen.

Page Up, Page Down

30

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.3 Option 3 Diagnostic Programs

Scroll a page backward or forward on the screen.

Esc

Exit the Log viewer.

F1

Display the Help information about the Log viewer operations and the functional keys.

Ctrl+Home

Go to the start of the log file.

Ctrl+End

Go to the end of the log file.

Ctrl+F3

Prompt the search dialogue for the user to input the string to be looked for and specify the searching method.

F3

Find the next corresponding strings given.

3.3.10 LOG File Sample

Log file is a test result file, which records the following information: Test module name,

Test item name, Start/End time and the test result (including PASS, FAIL, SKIP and

ABORT). When a failure is found, both the error code and the error information were recorded.

In the Log file, we use Test Items as the test item name, which could not be modified in the whole time. And we use the Internal Name as name in the program’s UI, which corresponds to the test item name and could be modified according to the user’s favorite.

The following section is a sample of log file:

DIAG REPORT

<Module Name>: Service Diagnostic Ver 1.00 ... Memory Tester Build Date 2006.01.10

[Walk High]

Begin Time: Wed Jul 05 10:45:36 2006

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 31

3 Diagnostic Programs 3.3Option

Base Memory Test : PASS

Extended Memory Test : PASS

End Time: Wed Jul 05 10:47:51 2006

<Module Name>: Service Diagnostic Ver 1.00 ... Mouse Test Build Date 2006.01.10

[MSTPad]

Begin Time: Wed Jul 05 10:48:54 2006

Touch Pad Test : FAIL

ITEM TEST FAIL

Function ID :502

Error Code :50202

Error Message :Touch Pad Test Fail

End Time: Wed Jul 05 10:49:16 2006

32

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.4 Subtests 3 Diagnostic Programs

3.4 Subtests

Test

Group

System

Sub

Item

ID

Subtest

01 CPU

Test

ID

Test items Internal Name

01 Basic Functionality Test [CPUBasicFun]

[CPUSpeed]

Coprocessor

[NPUFun]

04 [CPUInformation]

05 CPU Protected Mode [Protect]

0

6 MMX [MMX]

[DMACtrl]

03 Clock / Calendar

[Timer]

[RealClock]

05 Plug and Play

[PCI]

[PnP]

[ACPI]

03 FAN

Memory 01 BIOS ROM

Parity

03 Pattern

01 CPU Fan Speed Test

01 Bit Stuck High Test

02 Bit Stuck Low Test

03 Checker Board Test

04 CAS Line Test

05 Incremental Test

[FANSpeed]

[BIOSROM]

[

Parity

]

[BSHigh]

[BSLow]

[ChkBd]

[CASLine]

[Incrment]

06 Decremental Test

04 Extended Pattern 01 Write/Read Cycle Test

[Decrment]

07 Incremental Decremental Test [Idcrment]

[XWRCycle]

02 Read Cycle Test

05 Walking 1's Test

06 Walking 0's Test

07

Test

10 Random Memory 01 Randomize Test

[XRCycle]

[WalkHigh]

[WalkLow]

[Address]

[Refresh]

[CacheOne]

[Random]

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 33

3 Diagnostic Programs 3.4 Subtests

Video

11 Data Bus Test

01 Text Mode

02 Random Increment Read/Write [RandIncr]

[DataBus]

[MemSpeed]

Sequential/Random [SeqRdRW1]

[Perform1]

04 [Controller1]

05 [DiagRW1]

[SMART1]

[CDRWController]

02 Data Transfer Rate

03 Data CD Butterfly Seek

04 Data CD Random Seek

05 Data CD Sequence Seek

06 Tray Eject Test

01 Character Test

03 Text Page Selection

05 80*25 Text Mode

[CDRWTransRate]

[CDRWButterfly]

[CDRWSeek]

[CDRWSFSeek]

[CDRWTray]

[CharTest]

[Attribut]

[PageSel]

[Color]

[Text Mode]

[VGAMode]

01

640X480 Video Modes

VESA 640x480x256 Mode

VESA 640x480x

32K Mode

VESA 640x480x64K Mode

VESA 640x480x

16K Mode

VESA 640x480x32bit Mode

800X600 Video Modes

VESA 800x600x256 Mode

VESA 800x600x64K Mode

02

K Mode

VESA

800x600x16K Mode

VESA

800x600x32bit Mode

[V640480_15]

[V640480_16]

[V640480_24]

[V640480_32]

[V800600_15]

[V800600_16]

[V800600_24]

[V800600_32]

1024X768 Video Modes

VESA 1024x768x64K Mode

[V1024768_15]

[V1024768_16]

[V1024768_24]

34

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.4 Subtests 3 Diagnostic Programs

COMM

06 LCD Panel Test

Test

Color

09 Direct Color Test

VESA 1024x768x32

K Mode

VESA

1024x768x16K Mode

VESA

1024x768x32bit Mode

[V1024768_32]

[VESAMEM]

[AGP]

[LCDPanel]

[Register]

[ColPurity]

[DirectColor]

[DACPalAddr]

01 LAN Card

02 1394

Peripheral 01 Keyboard

01 Device ID Detection

02 Vendor ID Detection

03 Mac Address Detection

01 GUID Detection

01 Keyboard Data Line

02 Keyboard Clock Line

03 Device

[Bitblt]

[DeviceID]

[VendorID]

[MAC Address]

[1394 R/W Test]

[KBDataLn]

[KBClokLn]

[MSTpad]

[KBLED]

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 35

3 Diagnostic Programs 3.5 System Test

3.5 System Test

Move arrow keys and press the Space key to select CPU test item from Service

Diagnostic menu, then highlight CPU and press the Enter to run this test item.

Subtest 01 CPU

1. Basic Functionality Test

This test item is to check whether the CPU works normally through math and logic calculation, which means verifying the general registers, math registers and logic registers.

2. CPU Speed

This test item is to detect the work frequency of the current CPU. User should change the parameters setting in the following window before the test:

36

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.5 System Test 3 Diagnostic Programs

CPU Speed Comparison--Whether you want to make a comparison of the

CPU speed with the value set in ‘Expected CPU Speed’, you should choose

‘Yes’; otherwise, ‘No’.

Expected CPU Speed--Specify the expected CPU Speed value you want for further comparison.

Allowable Error Rate-- Specify the Allowable Error Rate value you want for further comparison.

3. Coprocessor

NPU Basic Functions Test

This test item is to check whether the precision of the numeric processor in the float calculation is up to the IEEE standards.

NPU Interrupt Test

This test item is to check whether NPU transfers the abnormal Interrupt program correctly by forcing an abnormal float.

4. CPU Information

This test item is used for getting & showing CPU Information. It will be displayed as follows:

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 37

3 Diagnostic Programs 3.5 System Test

5. CPU Protected Mode Test

This test item is to check whether CPU protected mode instruction works normally.

6. MMX

The test item is to confirm whether the CPU supports MMX instructions.

Subtest 02 Boards

1. DMA Controller

This test item is to check whether the DMA controller works normally.

2. Interval Timer

This test item is to check whether the Interval Timer (18.2Hz, 55ms) works normally.

3. Clock/Calendar

This test item is to check whether the system clock/calendar works normally.

4. PCI System

This test item is to check whether the bus number, device number and function number in PCI bus are valid.

5. Plug and Play

38

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.5 System Test 3 Diagnostic Programs

This test item is to check:

1. Whether the current system supports Plug-n-Play;

2. Whether there is an ESCD (Extended System Configuration Data) in the BIOS;

3. Whether there is PCI-to-ISA bridge in the system;

4. Whether there is PCI bus in the system.

6. ACPI Test

ACPI test includes two sub-items as below:

System Address Map Test: Check the correctness of ACPI system memory map, and whether its mapping scope is within real memory.

ACPI Table Test: Check the correctness of ACPI relative configuration tables in the current system.

Subtest 03 FAN Speed Test

1. CPU Fan Speed Test

This test item is to check whether the CPU fan currently used works normally in the different speeds of stop, slow, middle and fast. Below is the parameter setting dialog window.

Set the range of Speed that is to be tested, then choose the OK button to test it. It will be displayed as follows:

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 39

3 Diagnostic Programs 3.5 System Test

40

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.6 Memory Test 3 Diagnostic Programs

3.6 Memory Test

This test module is to check whether the memory chip works normally.

Subtest 01 BIOS ROM

This test item is to check the validity of BIOS ROM that includes two sub-items --

ROM Read and ROM Write Protection. ROM Read is to check whether BIOS

ROM could be correctly read out, ROM Write Protect is to check whether BIOS

ROM is write-protected.

Subtest 02 Parity

This test item is to check whether the parity checkout error could happen through writing and reading memory. Below is the parameter setting dialog window.

Test Option: Choose the Memory part to take the test– Base Memory or

Extended Memory.

Extended Memory Test Range: Specify the test coverage range of

Extended Memory. If user chooses Total Size, it means that the whole

Extended Memory will be tested. Although user can input the parameter into other select box, but the selected result is invalid. If user chooses

Special Size, the test of Extended Memory will be taken according to the coverage range that user chooses or time.

Extended Memory Start Address (MB) & Extended Memory End

Address (MB): Set the range of extended memory that is to be tested, the test coverage would be based on the setting and the value in ‘Percent (%) mentioned at below.

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 41

3 Diagnostic Programs 3.6 Memory Test

Pattern Size: Choose the pattern size – BYTE, WORD, DWORD or ALL.

Percent (%): Choose the percentage of the defined range of the memory to be tested.

Time Limit(h): Choose or Input the time (hour) of the defined range of the memory to be tested.

Time Limit(m): Choose or Input the time (minute) of the defined range of the memory to be tested.

Subtest 03 Patterns

This test item is to check whether the system memory includes base memory and extended memory that could be accessed correctly through writing and reading with a series of designed pattern data. Below is the parameter setting dialog window.

Test Option: Choose the Memory part to take the test– Base Memory or

Extended Memory.

Extended Memory Test Range: Specify the test coverage range of

Extended Memory. If user chooses Total Size, it means that the whole

Extended Memory will be tested. Although user can input the parameter into other select box, but the selected result is invalid. If user chooses

Special Size, the test of Extended Memory will be taken according to the coverage range that user chooses or time.

Extended Memory Start Address (MB) & Extended Memory End

Address (MB): Set the range of extended memory that is to be tested, the

42

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.6 Memory Test 3 Diagnostic Programs

test coverage would be based on the setting and the value in ‘Percent (%) mentioned at below.

Pattern Size: Choose the pattern size – BYTE, WORD, DWORD or ALL.

Percent (%): Choose the percentage of the defined range of the memory to be tested.

Time Limit(h): Choose or Input the time (hour) of the defined range of the memory to be tested.

Time Limit(m): Choose or Input the time (minute) of the defined range of the memory to be tested.

1. Bit Stuck High Test

Data pattern: Every bit is ‘1’ (Each bit is high)

2. Bit Stuck Low Test

Data pattern: Every bit is ‘0'(Each bit is low);

3. Checker Board Test

Data pattern: Lo-byte and hi-byte are composed with 0101(0x5) and 1010

(0xA);

4. CAS Line Test

Data pattern: Lo-byte and hi-byte are composed with 0000 (0x0) and

1111(0xF);

5. Incremental Test

Data pattern: A series of increasing data from 0 by adding 1 each time;

6. Decrement Test

Data Pattern: A series of decreasing data from the maximum (e.g. 0xFFFF) by subtracting 1 each time;

7. Incremental / Decrement Test

Data Pattern is a series of data whose low byte is increasing data from 0x00 and high byte is decreasing data from 0xFF.

Subtest 04 Extended Pattern

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 43

3 Diagnostic Programs 3.6 Memory Test

In addition to the above pattern test of the memory, there is Read/Write Cycle test and Read Cycle Test for the extended memory.

Below is the parameter dialog window of the extended pattern test.

Test Range: Specify the test coverage range of Extended Memory. If user chooses Total Size, it means that the whole Extended Memory will be tested. Although user can input the parameter into other select box, but the selected result is invalid. If user chooses Special Size, the test of Extended Memory will be taken according to the coverage range that user chooses or time.

Extended Memory Start Address and Extended Memory End

Address (MB): Set the range of extended memory that is to be tested.

The test coverage will be according to the value setting in ‘Percent

(%)’ mentioned at below.

Percent (%): Choose the percentage of the defined range of the memory to be tested.

Time Limit(h): Choose or Input the time (hour) of the defined range of the memory to be tested;

Time Limit(m): Choose or Input the time (minute) of the defined range of the memory to be tested.

1. Write/Read Cycle Test

Test by using both read and write instructions.

2. Read Cycle Test

44

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.6 Memory Test 3 Diagnostic Programs

Test by using read instructions.

Subtest 05 Walking 1’s Test

The test item is to ensure that there is no short circuitry issue in memory chip. The parameter dialog window is the same as that in ‘Subtest 02 Pattern’.

Subtest 06 Walking 0’s Test

The test item is to ensure that there is no open circuitry issue in memory chip. The parameter dialog window is the same as that in ‘Subtest 02 Pattern’.

Subtest 07 Memory Address

This test item is to check short and open issue on memory address lines.

Subtest 08 Refresh Test

This test item is to check whether the memory refresh works normally. The parameter dialog window is as follows:

Subtest 09 Cache Memory

The test item is to check whether the CPU internal cache memory could be accessed correctly.

Subtest 10 Random Memory

Random Memory test includes the following two test items: Randomize Test and

Random Incremental Read/Write Test. The parameter dialog window is the same as that in ‘Subtest 03 Extended Pattern’.

1. Randomize Test

This test item is to check whether the memory could be correctly accessed with randomized data and randomized memory address.

2. Random Increment Read/Write

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 45

3 Diagnostic Programs 3.6 Memory Test

This test item is to check whether the memory could be correctly accessed with randomized memory address and a series of incremental data.

Subtest 11 Data Bus Test

This test item is to check whether the data bus works normally.

Subtest 12 Memory Speed Test

This test item is to check the data-transferring rate for the cache memory and the system memory.

46

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.7 Storage 3 Diagnostic Programs

3.7 Storage

Subtest 01 HDD

This test item runs on IDE hard disks. It checks the functions and performance of IDE hard disk.

In order to protect user’s HDD data, the password must be verified before the

HDD test. The screen is as follows:

Password

hard disk

1. Sequential/Random R/W

This test item is to check the HDD’s Read/Write function through data writing and reading to HDD.

This test item needs user to submit the parameters:

IDE HDD Test Range-- Specify the test coverage range of IDE HDD. If user chooses Total Size, it means that the whole IDE HDD will be tested. Although user can input the parameter into other select box, but the selected result is invalid. If user chooses Special Size, the test of IDE HDD will be taken according to the coverage range that user chooses or time.

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 47

3 Diagnostic Programs 3.7 Storage

LBA Start, LBA End--Specify the start and end byte in LBA (Large Block

Address).

Percent—Specify the coverage rate in percentage of the total disk.

Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested.

Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested.

Test Mode—Choose test mode from the following options:

(1) Read & Write –Write data on the disk, then read it out and compare the two value;

(2) Read Verify —Read data only;

(3) Unprotected Write—Write data on the disk without backup original data.

Option—Select sequential test or random test

2. Sequential/Random Seek

The test item is to check the correctness of the HDD’s sector’s seeking function.

This test item involves the following parameters:

IDE HDD Test Range—is same as the description of the upper item.

LBA Start, LBA End-- specify start and finish byte in LBA(Large Block

Address);

Option-- Select sequential test or random test;

48

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.7 Storage 3 Diagnostic Programs

Percent-- Specify the coverage rate in percentage of the total disk.

Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested;

Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested.

3. Performance

Check the HDD’s seeking speed and transfer the data rate.

4. Controller Check

Check the HDD controller’s status, including HDD interrupt and unexpected interrupt.

5. Diagnostic Read/Write

This test item is a quick test to verify whether the HDD could be correctly accessed and the user could specify the percentage in the below dialog.

Percent (1-100)-- Specify the coverage rate in percentage of the total disk.

Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested;

Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested;

6. SMART Test

SMART stands for Self-Monitoring, Analysis and Reporting Technology.

SMART test will compare the attribute values with the threshold value in the

HDD’s controller to confirm whether there is any failure in the HDD

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 49

3 Diagnostic Programs 3.7 Storage

Subtest 02 ODD

The ODD test runs on IDE CDROM/DVD-ROM & CD-RW. It will check the ODD driver’s functionality and performance.

1. Controller Test

Check the CDROM controller’s status.

2. Data Transfer Rate

Check the data transfer rate of the ODD drive. It will read data from the ODD disc and calculate the data transfer rate. This test needs a data CD.

3. Data CD Butterfly Seek

Check the seek function of the ODD drive. It will perform a serial of seeking operations. First, locate the minimum LBA address, then the maximum, the subminimum, the sub-maximum and meet at center point. This test needs a data CD.

4. Data CD Random Seek

Check the random seek function of ODD drive. Random access will reflect the performance of the heads’ random movement and seek. It tests for 1000 times.

5. Data CD Sequence Seek

Check the sequential seek function of ODD drive. Perform location test to CD-

RW under LBA mode with the location address increasing in sequence.

6. Tray Eject Test

Check the eject function of the ODD. It will eject the ODD and ask the user to confirm if the operation succeeds.

50

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.8 Video 3 Diagnostic Programs

3.8 Video

This test item tests the video by:

1. displaying the figures in different graphic modes.

2. displaying the property and color of the characters in different text modes.

User will confirm whether each video mode works normally by judging whether the display is correct. It checks whether the video memory works normally by writing data into the video memory, then reading it out and comparing the two value.

Subtest 01 Text Mode

1. Character Test

Tests two types of font patterns.

Font 9*14

Font 9*16

It requires the user to check whether all characters of each font type displayed correctly by answering the questions prompted on screen. It will be displayed as follows:.

2. Text Attribute

This test item is to check whether the text attribute of normal, hi-intensity, inverse, and blinking in VGA text mode could be correctly displayed on the screen.

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 51

3 Diagnostic Programs 3.8 Video

It would display the below texts of the different attributes in the screen:

1. Text in normal attribute;

2. Text in blinking normal attribute;

3. Text in inverse attribute;

4. Text in blinking inverse attribute;

5. Text in hi-intensity attribute;

6. Text in blinking hi-intensity attribute;

Users need to check whether all texts displayed correctly in the above six attributes and key in the answer ‘Y’ or ‘N’ to the prompts ‘Is this display OK?

[Y/N<Enter=Y>]’.

Below is the test screen of Text Attribute.

3. Text Page Selection

This test item is to check whether the video memory could be correctly written and read in VGA text mode. According to the comparison of written data with read data, the program would report PASS or FAIL.

52

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.8 Video 3 Diagnostic Programs

4. Text Color

This test item is to check whether all 16 colors foreground and all 8 colors background works normally in VGA text mode.

The bit4-6 of the attribute byte of a character defines 8 background colors (black, blue, green, cyan, red, brown, magenta, and light gray), and the bit0-3 defines 16 foreground colors (dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and white besides the above 8 colors).

In the test, user is required to respond according to the instruction in the screen.

5. 80 * 25 Text Mode

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 53

3 Diagnostic Programs 3.8 Video

This test item is to check whether 80*25 Text Mode works normally.

In the test, user is required to respond according to the instruction in the screen.

Subtest 02 640 * 480 VGA Mode

This test item is to check whether 680*480 VGA Text mode works normally.

In the test, user is required to respond according to the instruction in the screen.

54

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.8 Video 3 Diagnostic Programs

Subtest 03 VESA Video Modes

This test item is to check whether all the video modes supported by the video card works normally.

In the test, user is required to respond following the instruction in the screen.

1. 640X480 Video Modes Test

2. 800X600 Video Modes Test

3. 1024X768 Video Modes Test

Subtest 04 VESA Video Memory

This test item is to check whether VESA video memory could be correctly accessed (write data & read data). Below is the test item’s parameter dialog window:

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 55

3 Diagnostic Programs 3.8 Video

If press Ctrl+Break to force the test to terminate during execution of VESA

Video Memory, the test program will not operate and display properly in further tests.

Subtest 05 AGP Test

This test item is to report the system’s Accelerated Graphics Port status and check whether AGP registers works normally.

Subtest 06 LCD Panel Test

This test item is to check whether there is any fault in its resolution by displaying the RGB gradient color screens.

56

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.8 Video 3 Diagnostic Programs

Subtest 07 Register Test

This test item is to check whether the registers of the video adapter works normally.

Subtest 08 Color Purity Test

This test item is to check whether the system (the video adapter and the display) could display the purity color of red, green, blue, black and white.

In the test, user is required to respond according to the instruction in the screen.

Subtest 09 Direct Color Test

This test item is to check the video adapter’s composing ability of direct color in high and true color mode.

In the test, user is required to respond according to the instruction in the screen.

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 57

3 Diagnostic Programs 3.8 Video

Subtest 10 DAC/Palette Address

This test item is to check the function of DAC registers and Palette registers.

In the test, user is required to respond according to the instruction in the screen.

58

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.8 Video 3 Diagnostic Programs

3.9 Communication (COMM)

Subtest 01 LAN Card

This test item is to check whether the module can detect the existence of the network card and display its related information.

1. Device ID Detection

Detect the device ID of the network card.

2. Vendor ID Detection

Detect the vendor ID of the network card.

3. MAC Address Detection

Detect the MAC address of the network card.

Subtest 02 1394

GUID Detection

This test item is used to read and display GUID from 1394 register.

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 59

3 Diagnostic Programs 3.10 Peripheral

3.10 Peripheral

Subtest 01 Keyboard

This test item is to check whether the keyboard works normally.

1. Keyboard Data Line Test

Check whether the keyboard data line works normally.

2. Keyboard Clock Line Test

Check whether the keyboard clock line works normally.

Subtest 02 Mouse Test

Check whether the point devices work normally.

1. Touch Pad

Before test Touch Pad’s function, user should set a timeout time at below screen:

At the below screen of Touch Pad test, user can press the left button, right button, and move the mouse to verify its functions for times, and the test will end either by user break or test time is out.

60

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.10 Peripheral 3 Diagnostic Programs

Subtest 03 Led Test

1. Led Test

Check whether the green led works normally.

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 61

3 Diagnostic Programs

Check whether the orange led works normally.

3.10 Peripheral

Check whether the HDD led works normally.

62

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.10 Peripheral 3 Diagnostic Programs

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 63

3 Diagnostic Programs 3.11Error Codes and Description

3.11 Error Codes and description

The format of ‘Error Code’ is ‘ddxxee’, and ‘dd’ is the device ID (1~2 chars), ‘xx’ is test function

ID of device (2 chars), ‘ee’ is the error code of device (2 chars); the range of error code is from 01 to 99 in each device (the common error codes in all device are set to 99 and spanned).

Device

Error

Code

Description Cause

94 Interactive Mode Needed

The test is not under interactive mode.

Action

Check whether the interactive test mode is adopted.

The CPU General Function register is damaged.

The CPU Arithmetic Register is damaged.

The CPU Logic Register is damaged.

The CPU Type is not supportable.

The CPU speed differs from the expected value.

The NPU arithmetic unit is damaged.

The NPU is damaged.

Information of the CPU cannot be acquired.

The ROM BIOS has Physical problems.

The ROM BIOS has Physical problems.

Replace the CPU.

As above.

As above.

Check whether the CPU is Intel

CPU.

Check the CPU speed and the set expected speed.

Replace the CPU.

As above.

Check whether the CPU is Intel

CPU.

Replace the CPU.

Test this unit on multiple machines.

As above.

The test pattern read out from the base memory is different from Test this memory chip on the one that has been written in this address. multiple machines.

The test pattern read out from the extension memory is different from the one that has been

As above. written in this address.

Wrong parameters setup. Check and reset the parameters.

64

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.11 Error Codes and Description 3 Diagnostic Programs

12 Data Bus Error

Interference between different address channels.

Errors with the timer chip.

Test this memory chip on multiple machines.

As above.

The acquired refreshing frequency is out of the estimated range.

Reset the estimated range.

The pattern read out from the L1

Cache is different from the one that has been written in the same address.

Test this unit on multiple machines.

Interference between different data channels.

As above.

Failure during the transfer speed test.

DMA channel cannot transfer data normally.

As above.

Repeat multiple times. Whether there is always the same error, replace the board.

The difference between the actual precision of the interval timer and its theory value is out of the permitted range. The timer counts imprecisely.

As above.

The frequency is beyond the standard.

The frequency is below the standard.

R/W errors with the RTC refreshing interrupt controller.

As above.

As above.

As above.

The PC speaker's sound source --

-counter/timer 8253 cannot produce corresponding timing signal.

As above.

No PCI. Check the board.

PCI test fails. As above.

As above.

Wrong PCI configuration.

ESCD errors.

Check PCI configuration on main board or PCI Device configuration.

Repeat multiple times. If there is always the same error, replace the board.

As above.

53 Errors with the ACPI table test. As above.

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 65

3 Diagnostic Programs 3.11Error Codes and Description

01 Fan Slow Speed Test Fail The fan slow speed test fails. Check the FAN connection.

02 Fan Stop Test Fail The fan stop test fails. As above.

03 Fan Fast Speed Test Fail The fan fast speed test fails.

01 Text Attribute Error

As above.

Physical problems with the video card.

Check whether there is any physical problem with the video card.

02 Text Page Selection Error As above. As above.

03 Text Color Error

04 Text Mode Error

05 VGA Mode Error

06 Character Test Error

As above. As above.

As above.

1) Physical problems with the video card.

2) Physical problems with the monitor.

As above.

1) Check whether there is any physical problem with the video card.

2) Check whether there is any physical problem with the monitor.

Physical problems with the video card.

Check whether there is any physical problem with the video card.

As above. As above.

08 Color Purity Test Error

Physical problems with the video card or the monitor.

Check whether there is any physical problem with the video card or the monitor.

VESA Mode 15bits Direct

As above. As above.

VESA Mode 16bits Direct

As above. As above.

VESA Mode 24bits Direct

As above. As above.

Get the PCX graphics map Failure in getting PCX graphics map.

13 Bitblt Engine Test Error

Check for the PCX graphics map.

Physical problems with the video card.

Check and see whether the video card has any physical problem.

As above. As above.

15 VESA VRAM Test Error

16 AGP Test Error

Physical problems with the video card or the monitor.

Check whether there is any physical problem with the video card or the monitor.

AGP configuration register errors.

Check and see whether the AGP video card has any physical problem.

17 LCD Panel Test Error Lower LCD color resolution. Replace the LCD.

66

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.11 Error Codes and Description 3 Diagnostic Programs

19 Register Test Error

20 Adapter not support DDC

21 Monitor not support DDC

Physical problems with the video card.

Check and see whether the video card has any physical problem.

The video card doesn't support

DDC.

The monitor doesn't support

DDC.

1) Physical problems with the video card.

2) Physical problems with the monitor.

1) Check and see whether the video card has any physical problem.

2) Check and see whether the monitor has any physical problem.

As above. As above.

As above. As above.

As above. As above.

As above. As above.

01 Audio Play Fail

02 Record Fail

As above.

Cannot play music.

Cannot record.

Don’t Scan PCI

device

As above.

Check the Audio connection, replace the external fixture, and repeat the test.

As above.

Don’t support PCI BIOS

PCI Ethernet card not test

Intel PCI Ethernet card test

01 Touch Pad Test Fail

Don’t find Net card Please insert Net cad

Don’t found Net Card, This Card can’t be Read MAC by this method

Please update net card or use other method

Keyboard Map & Stroke Test fails.

Clock Line Test fails.

Data Line Test fails.

Touch Pad Test Fail

Check the KBD connection and repeat the test.

As above.

As above.

Check the mouse connection and repeat the test.

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 67

3 Diagnostic Programs 3.11Error Codes and Description

01

01 Get Parameter Fail !

02 Write Pattern Error

03 Data Compare Error

04 Read Verify Error

Disk Controller Test

Failed

Can not find IEEE1394 controller

Wrong test parameters are input by user.

HD is damaged.

HD is damaged.

HD is damaged.

HD is damaged.

Don’t support 1394.

Reinput the correct parameters.

Send the HD for repair.

As above.

As above.

As above.

The HD controller is damaged. As above.

The HD controller is damaged. As above.

The HD controller is damaged. As above.

Disk dos not support SMART

Change HD which supported

SMART and test again

Disk read attribute threshold error

Send the HD for repair.

Disk read attribute value error As above.

Disk SMART attribute value error

No disk is found in the CD-

ROM.

The disk in the CD-ROM is not

Data Disk.

As above.

Insert a disk into the CD-ROM.

Insert a DATA CD.

Send the CD-ROM for repair.

ROM.

Either the disk or the CD-ROM is damaged.

Either the disk or the CD-ROM is damaged.

Wrong CD-ROM drive.

Replace the disk or send the CD-

ROM for repair.

Replace the disk or send the CD-

ROM for repair.

Exit from the wrong drive.

68

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual

3.12 Quick Test Item List

3.12 Quick Test Item List

CPU Basic Functionality

NPU Basic Functions

Bit Stuck High Test

Bit Stuck Low Test

Clock / Calendar

Video

HDD

LAN Card

1024X768 Video Modes Test:

VESA 1024x768x64K Mode

VESA 1024x768x32bit Mode

VESA Video Memory

Direct Color Test

Sequential/Random Read

Device ID Detection

Vendor ID Detection

3 Diagnostic Programs

10% or 3 minutes

10% or 3 minutes

10% or 3 minutes

25% or 3 minutes

Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual i

4

Chapter 4

Replacement Procedures

1

4 Replacement Procedures

4-ii Satellite/E200/E205 Maintenance Manual

4 Replacement Procedures

Chapter 4 Contents

4.1 General.........................................................................Error! Bookmark not defined.

Safety Precautions..................................................Error! Bookmark not defined.

Before You Begin ..................................................Error! Bookmark not defined.

Disassembly Procedures ........................................Error! Bookmark not defined.

Assembly Procedures.............................................Error! Bookmark not defined.

Tools and Equipment .............................................Error! Bookmark not defined.

Screw Tightening Torque ......................................Error! Bookmark not defined.

Colors of Screw Shanks .........................................Error! Bookmark not defined.

Symbols of Screws on the Computer Body ...........Error! Bookmark not defined.

Symbol examples ...................................................Error! Bookmark not defined.

4.2 Battery Pack/Bridge Media..........................................Error! Bookmark not defined.

Removing the Battery Pack ...................................Error! Bookmark not defined.

Installing the Battery Pack.....................................Error! Bookmark not defined.

4.2.2 Bridge Media (SD Card / Memory Stick / xDPicture Card) .......... Error!

Bookmark not defined.

Removing the Bridge Media..................................Error! Bookmark not defined.

Installing the Bridge Media ...................................Error! Bookmark not defined.

4.3 Keyboard......................................................................Error! Bookmark not defined.

Removing Keyboard ..............................................Error! Bookmark not defined.

Installing the Keyboard..........................................Error! Bookmark not defined.

Removing the Bottom Cover .................................Error! Bookmark not defined.

Installing the Bottom Cover...................................Error! Bookmark not defined.

Removing the Display Assembly...........................Error! Bookmark not defined.

Installing the Display Assembly ............................Error! Bookmark not defined.

Satellite/E200/E205 Maintenance Manual 4-iii

4 Replacement Procedures

Removing the Memory Module.............................Error! Bookmark not defined.

Installing the Memory Module ..............................Error! Bookmark not defined.

4.7 Wireless LAN Card......................................................Error! Bookmark not defined.

Removing the Wireless LAN Card ........................Error! Bookmark not defined.

Installing the Wireless LAN Card .........................Error! Bookmark not defined.

4.8 HDD.............................................................................Error! Bookmark not defined.

Removing the HDD ...............................................Error! Bookmark not defined.

Installing the HDD.................................................Error! Bookmark not defined.

4.9 ODD Bay Module ........................................................Error! Bookmark not defined.

Removing the ODD Bay Module ..........................Error! Bookmark not defined.

Installing the ODD Bay Module............................Error! Bookmark not defined.

Disassembling the ODD Drive ..............................Error! Bookmark not defined.

Assembling the ODD Drive...................................Error! Bookmark not defined.

Removing the Bluetooth module ...........................Error! Bookmark not defined.

Installing the Bluetooth Module ............................Error! Bookmark not defined.

4.11 CPU Cooling Module and Fan.....................................Error! Bookmark not defined.

Remove the CPU cooling module and Fan............Error! Bookmark not defined.

Installing the CPU Cooling Module and Fan.........Error! Bookmark not defined.

4.12 CPU..............................................................................Error! Bookmark not defined.

Removing the CPU ................................................Error! Bookmark not defined.

Installing the CPU..................................................Error! Bookmark not defined.

Removing the System Board .................................Error! Bookmark not defined.

Installing the System Board...................................Error! Bookmark not defined.

4.14 Speakers .......................................................................Error! Bookmark not defined.

Removing the Speakers..........................................Error! Bookmark not defined.

Installing the Speakers ...........................................Error! Bookmark not defined.

4.15 Switch Board and Finger Print Board..........................Error! Bookmark not defined.

Removing Switch Board and Finger Print Board ..Error! Bookmark not defined.

Installing Switch Board and Finger Print Board....Error! Bookmark not defined.

4.16 Light Sensor Board and Audio Board..........................Error! Bookmark not defined.

4-iv Satellite/E200/E205 Maintenance Manual

4 Replacement Procedures

Removing the Light Sensor Board and Audio Board .......... Error! Bookmark not

defined.

Installing the Power Board, Switch Board and Logo LED Board................. Error!

Bookmark not defined.

4.17 DC-IN cable, RGB Board and RJ45 cable...................Error! Bookmark not defined.

Removing DC-IN cable, RGB Board and RJ45 cable......... Error! Bookmark not

defined.

Installing DC-IN cable, RGB Board and RJ45 cable .......... Error! Bookmark not

defined.

Open Display Mask................................................Error! Bookmark not defined.

Removing the Display Mask..................................Error! Bookmark not defined.

Installing the Display Mask ...................................Error! Bookmark not defined.

Open LCD module.................................................Error! Bookmark not defined.

Removing the LCD module ...................................Error! Bookmark not defined.

Installing the LCD Module ....................................Error! Bookmark not defined.

4.20 CCD Board and MIC ...................................................Error! Bookmark not defined.

Removing the CCD Board and MIC......................Error! Bookmark not defined.

Installing the CCD Board and MIC .......................Error! Bookmark not defined.

4.21 LED Board and Card Reader Board ............................Error! Bookmark not defined.

Removing the LED Board and Card Reader BoardError! Bookmark not defined.

Installing the LED Board and Card Reader Board Error! Bookmark not defined.

Satellite/E200/E205 Maintenance Manual 4-v

4 Replacement Procedures

Figures

Figure 4-1 Removing the battery pack ....................................Error! Bookmark not defined.

Figure 4-2 Removing the Bridge Media ..................................Error! Bookmark not defined.

Figure 4-3 Removing the keyboard ........................................Error! Bookmark not defined.

Figure 4-4 Removing the bottom cover ...................................Error! Bookmark not defined.

Figure 4-5 Removing the screws from the top of the computer ............ Error! Bookmark not

defined.

Figure 4-6 Removing the screws from the bottom of the computer and bottom cover ... Error!

Bookmark not defined.

Figure 4-7 Removing the display assembly.............................Error! Bookmark not defined.

Figure 4-8 Removing the memory module..............................Error! Bookmark not defined.

Figure 4-9 Removing the wireless LAN card..........................Error! Bookmark not defined.

Figure 4-10 Removing the HDD pack .....................................Error! Bookmark not defined.

Figure 4-11 Removing the HDD chassis .................................Error! Bookmark not defined.

Figure 4-12 Removing the ODD bay module..........................Error! Bookmark not defined.

Figure 4-13 Removing the bracket from the ODD drive.........Error! Bookmark not defined.

Figure 4-14 Removing the Bluetooth module .........................Error! Bookmark not defined.

Figure 4-15 Removing the fan and CPU cooling module........Error! Bookmark not defined.

Figure 4-16 Applying silicon grease........................................Error! Bookmark not defined.

Figure 4-17 Replace new thermal pad into correct position....Error! Bookmark not defined.

Figure 4-18 Tear down the tape...............................................Error! Bookmark not defined.

Figure4-19 Removing the CPU ...............................................Error! Bookmark not defined.

Figure4-20 Removing the CPU Mylar.....................................Error! Bookmark not defined.

Figure 4-21 Installing the CPU................................................Error! Bookmark not defined.

Figure 4-22 Securing the CPU.................................................Error! Bookmark not defined.

Figure 4-23 Disconnect from system board.............................Error! Bookmark not defined.

Figure 4-24 Removing the system board.................................Error! Bookmark not defined.

Figure 4-25 Removing the speakers ........................................Error! Bookmark not defined.

Figure 4-26 Removing the switch board and finger print board............ Error! Bookmark not

defined.

Figure 4-27 Removing the touch pad and button board ..........Error! Bookmark not defined.

Figure 4-28 DC-IN cable, RGB Board and RJ45 cable...........Error! Bookmark not defined.

4-vi Satellite/E200/E205 Maintenance Manual

4 Replacement Procedures

Figure 4-29 Removing the display mask .................................Error! Bookmark not defined.

Figure 4-30 Removing the LCD module and screws...............Error! Bookmark not defined.

Figure 4-31 Removing the LCD module .................................Error! Bookmark not defined.

Figure 4-32 Removing the CCD board and MIC.....................Error! Bookmark not defined.

Figure 4-33 Removing LED Board and card reader board......Error! Bookmark not defined.

Satellite/E200/E205 Maintenance Manual 4-vii

4.1 General 4 Replacement Procedures

4 1

4.1 General

This chapter explains how to disassemble the computer and replace Field Replaceable Units

(FRUs). Some replacement procedures may not require you to remove all the surrounding

FRUs to replace only one FRU. The chart below shows the FRUs in the order in which they should be removed in a top-down manner, irrespective of their physical locations. The FRUs shown in the top area of the chart should normally be removed before removing the FRUs shown in the bottom area. To replace the FRUs, first identify the suspect FRU for the system failure. Next, according to this chart, determine the FRUs that need to be removed before removing the suspect FRU. After you determine those FRUs, go to the appropriate sections according to the section numbers shown in the boxes. Then start removal and replacement.

4. 3

4.5

4. 6

Display assembly

4. 7

Memory module

4. 10

Bluetooth

Module

Keyboard

4. 8

4. 14

HDD

Speakers

4. 4

Wireless LAN Card

Bottom Cover

4. 9

ODD

Module

4. 11

4. 12

CPU

Cooling Module and fan

4. 15

Switch board and

Finger Print Board

4. 13

System Board

4. 16

Light sensor Board and

Audio Board

4. 21

Card Reader Board

4.17

and

LED Board and

RJ45 cable

,

4. 18

Display Mask

4. 19

LCD Modules

4. 20

CCD Board and MIC

How to use the chart (two examples):

 For removing the System Board:

First, remove the top cover with the display assembly. Then, remove the

HDD, selectable bay module,

Bluetooth card, keyboard, and wireless LAN card, all of which are shown above the top cover with the display assembly.

4 2.

4. 3

4.5

Keyboard

4. 6

Display assembly

4. 7

Memory module

4. 8

HDD

4. 4

Bottom Cover

Wireless LAN Card

4. 9

4. 11

Cooling Module and fan

ODD

Module

4. 12

CPU

4. 13

System Board

4. 21

LED Board and

Card Reader Board

 For removing the LCD Module:

First, remove the display mask and

FL inverter board, both of which are shown above the LCD module.

4. 10

Bluetooth

Module

4. 14

Speakers

4. 15

Switch board and

Finger Print Board

4. 16

Light sensor Board and

Audio Board

4.17

, and

RJ45 cable

4. 18

Display Mask

4. 19

LCD Modules

4. 20

CCD Board and MIC

System Board

LCD Module

Satellite/E200/E205 Maintenance Manual 4-1

4 Replacement Procedures 4.1 General

Safety Precautions

Before you begin to disassembly read the following safety precautions carefully. Be sure to follow them while you are working.

DANGER:

1. Always use the genuine batteries or replacement batteries authorized by Toshiba.

Batteries other than those differ in specifications and are incompatible with the computer. They may burst or explode. To avoid leakage of alkaline solutions, never heat or disassemble the battery packs. Never throw the battery packs into a fire. If this is violated, they will explode.

2. The components such as the power supply and FL inverter carry high voltages.

When you partially disassemble the computer and turn on the components, use extreme care not to touch the connectors and components to avoid the risk of electrical shock. Do not disassemble individual components during first-level maintenance.

WARNING:

1. To avoid the risk of electrical shock, turn the computer off and remove the AC adapter from the electrical outlet.

2. Because the battery in the computer is left charged, the risk of electrical shock remains even after the AC adapter is removed from the electrical outlet. To avoid the risk of electrical shock, be sure to remove any metal jewelry or accessories such as necklaces, bracelets, and rings before starting work. Never work with damp or wet hands.

3. To avoid personal injury, use care to avoid the sharp edges or corners of the components.

4-2 Satellite/E200/E205 Maintenance Manual

4.1 General 4 Replacement Procedures

CAUTION:

1. Before replacing a component, make sure that the replacement component meets the required specifications. To avoid computer failures, never use components that do not meet the specifications.

2. To avoid internal damage such as short circuits and fire, never drop metal objects such as screws, pins, paper clips, etc. into the components. When a screw is removed, be sure to replace a screw that is the same size as the original screw.

Make sure that all the screws are fastened securely. Loose screws can cause short circuits, overheating, smoke, or fire.

3. Before raising a FRU or other component, make sure that all the component cables have been disconnected to avoid the risk of electrical shock caused by accidental contact with the energized components.

4. For AC input, be sure to use the AC adapter and AC power cable that come with your computer or Toshiba-recommended equivalents.

5. To avoid the risk of electrical shock, make sure that all the replacement components meet the specifications of the computer and that all the cables and connectors are fastened securely.

6. Inside the PC are components that become hot during operation (such as the

CPU and cooling module). To avoid burns, let the hot components cool down before starting inspection or repair task.

Satellite/E200/E205 Maintenance Manual 4-3

4 Replacement Procedures 4.1 General

Before You Begin

Before you begin to disassembly the computer, keep in mind the precautions and advice in this section. Always begin disassembly by removing the AC adapter and battery pack.

Remove the optional parts and accessories as well. The procedures for removing the batteries will be explained later.

Disassemble the computer only when an abnormality has occurred.

Use only the recommended tools.

To run and store the computer, be sure to prepare a working environment that is free from:

Dust and contaminants

Static electricity

Extremely high or low temperatures and extremely high humidity

Run the diagnostic tests explained in Chapter 2 of this manual to identify the FRU that has probably caused the system failure.

Perform only the required machine operations. Use only the disassembly and reinstallation procedures described in this manual.

Place the removed components in a safe place away from the computer so that they are not damaged or get in the way of you doing your work.

Normally, a number of screws need to be removed or replaced during disassembling. Place the removed screws in a safe place so that you can easily find the right screws for the right components.

When assembling the computer, use the specified screws to fasten the parts to the specified locations. See the appropriate explanations and figures for screw sizes.

To avoid personal injury, use care to handle components that have sharp edges or corners.

After you have replaced a FRU, check that the FRU works correctly to ensure normal computer operation.

4-4 Satellite/E200/E205 Maintenance Manual

4.1 General 4 Replacement Procedures

Disassembly Procedures

The cable connectors come in these two basic types:

Pressure plate connectors

Normal pin connectors

To remove a pressure plate connector, pull up the tabs on either side of the connector's plastic pressure plate and gently pull the cable out of the connector. To reconnect the cable to the pressure plate's connector, raise the pressure plate up to a satisfactory height and slide the cable into the connector. Secure the cable in the correct position by pressing down the sides of the pressure plate so that the plate is flush with the sides of the connector. Grasp and pull the cable gently to check that the cable is connected firmly. If the cable comes off the connector, reinsert the cable by raising the pressure plate up to a satisfactory height.

Normal pin connectors are used for all the other types of cables. These connectors can be installed or removed by simply inserting them or pulling them out.

Assembly Procedures

You have to reassemble the computer after you have disassembled the computer and fixed the component that caused the problem.

When reassembling the computer, keep the following general guidelines in mind:

 Take your time to carry out the suggested instructions completely. Hurried reassembly can often cause problems.

 Check that all the cable and connectors are fastened securely.

 Before securing the FRUs or other parts, check that the cables are not caught by the screws or FRUs.

 Check that all the latches are closed securely.

 Check that all the required screws are used to secure the FRUs. Using wrong screws can damage the threads or heads of the screws or does not ensure that the FRUs are secure.

After installing a FRU, make sure that the FRU and computer work normally.

Satellite/E200/E205 Maintenance Manual 4-5

4 Replacement Procedures 4.1 General

Tools and Equipment

For your safety and that of other people in the working environment, it is strongly recommended that you use electrostatic discharge (ESD) equipment. The proper use of this equipment will ensure successful repair work and reduce the costs for repairing damaged components. The equipment and tools required for disassembly and reassembly are:

One 2 mm Phillips screwdriver

One 4 mm flat-blade screwdriver

Torx screwdriver

Tweezers (for pulling out screws)

ESD mats (for the floor and work desks)

An ESD wrist strap or heel grounder

Anti-static carpets or flooring

Air ionizers (for highly electrostatic sensitive areas)

A plastic card (in credit card size)

Screw Tightening Torque

To secure screws, follow the torque values listed below. Over tightening can damage components and screws. Under tightening can loosen the screw or cause screws to come off, which may result in short circuits or other damage.

 M2 (2 mm)

 M2.5 (2.5 mm)

0.22 N・m (2.2 kgf・cm)

0.36 N・m (3.5 kgf・cm)

 M3 (3 mm) 0.51 N・m (5.0 kgf・cm)

 M2.5x4 PSP TITE screws 0.204 N・m (2.0 kgf・cm)

 M2.5x6 GIZA TITE screws 0.36 N・m (3.5 kgf・cm)

4-6 Satellite/E200/E205 Maintenance Manual

4.1 General 4 Replacement Procedures

Colors of Screw Shanks

For easy identification of the correct screws, the screw shanks are colored according to their lengths, as follows:

 Screws of an even-numbered length Brown

 Screws of an odd-numbered length White

Screws of a special length

Black

Screws of a special length are those of a length having decimal places, such as 2.5 mm and 2.6 mm.

Symbols of Screws on the Computer Body

For easy maintenance, the screw types are shown on the computer body as symbols. A symbol consists of a letter representing the screw type and a numeral representing the screw length.

 Screw type

 Bind screw

 Flat-head screw

Super flat-head screw

 Tapping screw

Other screws

Symbol examples

Letter

B (stands for bind)

F (stands for flat-head)

S (stands for super flat-head)

T (stands for tapping)

U (stands for unique-pan head screws, studs, etc.)

 6 mm bind screw B6

 12 mm bind screw B12

 5 mm stud U5

(The numeral represents the rounded length of the threaded portion regardless of the entire stud length.)

Satellite/E200/E205 Maintenance Manual 4-7

4 Replacement Procedures

4.2 Battery Pack/Bridge Media

4.2 Battery Pack/Bridge Media

4.2.1 Battery Pack

Removing the Battery Pack

Remove the battery pack according to the following procedures and Figure 4-1.

CAUTION: When handling the battery packs, use care not to short circuit the terminals. Do not drop, hit, twist, or bend the battery packs. Do not scratch or break up their casing.

1. Turn the computer upside down so that the back is facing you.

2. Slide out the battery lock.

3. Slide the battery release latch and remove the battery pack from the computer.

Battery lock

1

2

Battery latch

Battery

Figure 4-1 Removing the battery pack

NOTE: Dispose of the used battery packs as required by local ordinances or regulations.

4-8 Satellite/E200/E205 Maintenance Manual

4.2 Battery Pack/Bridge Media 4 Replacement Procedures

Installing the Battery Pack

Install the battery pack according to the following procedures and Figure 4-1.

CAUTION: The battery packs contain a lithium ion battery, which can explode due to improper replacement, use, handling, or disposal. Always dispose of the battery packs as required by local ordinances or regulations. Use only replacement batteries recommended by Toshiba.

NOTE: Visually check the battery's terminals. If they are dirty, clean them with a dry cloth.

1. Gently insert a new or recharged battery pack into place. Check that the battery release latch slides in and stops with a click.

2. Slide in the battery lock.

Satellite/E200/E205 Maintenance Manual 4-9

4 Replacement Procedures 4.2 Battery Pack/Bridge Media

4.2.2 Bridge Media (SD Card / Memory Stick / xDPicture Card)

Removing the Bridge Media

Remove the Bridge Media according to the following procedures and Figure 4-2, after checking that the computer is turned off in boot mode.

1. Push a Bridge media. It will pop out partly when you release, so pull out the Bridge media.

Bridge media

Figure 4-2 Removing the Bridge Media

4-10 Satellite/E200/E205 Maintenance Manual

4.2 Battery Pack/Bridge Media 4 Replacement Procedures

Installing the Bridge Media

Install the Bridge Media according to the following procedures and Figure 4-2, after checking that the computer is turned off in boot mode.

1. Insert a Bridge media and press it until it is securely connected.

After the Bridge media is installed, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the Bridge media is compatible with the current hardware configuration.

Satellite/E200/E205 Maintenance Manual 4-11

4 Replacement Procedures 4.3 Keyboard

4.3 Keyboard

Removing Keyboard

Remove the Keyboard according to the following procedures and Figure 4-3.

1. Release the following 10 latches on the keyboard cover, in that order:

- Five bottom latches.

- Five front latches.

2. Remove the keyboard cover.

3. Remove two M2.5x2.5 black flat head screws.

4. Disconnect the keyboard cable from CN250 and CN251 on the system board.

5. Remove the keyboard. black flat screw

Keyboard cover

Keyboard

Latch

4-12

CN250

CN251

Figure 4-3 Removing the keyboard

Satellite/E200/E205 Maintenance Manual

4.3 Keyboard 4 Replacement Procedures

Installing the Keyboard

Install the keyboard according to the following procedures and Figure 4-3.

1. Connect the keyboard cable to CN250 and CN251 on the system board.

2. Secure the keyboard with two M2.5x2.5 black flat head screws.

3. Place the keyboard cover in the correct position and secure the following 10 latches, in that order:

- Five bottom latches.

- Five front latches.

Satellite/E200/E205 Maintenance Manual 4-13

4 Replacement Procedures 4.4 Bottom Cover

4.4 Bottom Cover

Removing the Bottom Cover

Remove the Bottom cover according to the following procedures and Figures 4-5 and 4-6.

1. Release the following 15 latches on the bottom cover, in that order:

- Four bottom latches on right sides.

- Two latches on right sides and three latches on left side.

- Six front latches.

2. Remove the bottom cover.

3. Open the display panel and remove the following 6 screws:

- Five M2x6 black flat head screws.

- One M2x5 white flat head screw.

4. Remove the left and right side hinge cover.

5. Turn the computer upside down and remove following 9 seal tapes:

- Four seal tapes on front side.

- One seal tape on right side.

- Two seal tapes on rear side

- Two seal tapes on back side.

6. Remove the following 13 screws on the bottom cover:

- Six M2.5x5 white flat head screws.

- Three M2x6 black flat head screws.

- Two M2.5x4 black flat head screws.

- Two M2.5x6 black flat head screws.

7. Hold up the bottom cover.

8. Disconnect the RGB board cable from CN204.

9. Disconnect the LED board cable from CN205.

10. Lift up the bottom cover. Release the following 15 latches on the bottom cover, in that order:

- Four bottom latches on right sides.

- Two latches on right sides and three latches on left side.

- Six front latches.

11. Remove the bottom cover.

4-14 Satellite/E200/E205 Maintenance Manual

4.4 Bottom Cover

Bottom cover

Latch

4 Replacement Procedures

Figure 4-4 Removing the bottom cover

M2x6 black flat head screw

M2x5 white flat head screw

Figure 4-5 Removing the screws from the top of the computer

M2x5 white flat head screw

Seal

M2x5 white flat head screw

Seal flat head screw

Left side hinge cover

M2x6 black flat head screw

Seal

Card reader board cable flat head screw

Right side hinge cover

CN204

CN205

M2x5 white flat head screw

LED board cable

Figure 4-6 Removing the screws from the bottom of the computer and bottom cover

Satellite/E200/E205 Maintenance Manual 4-15

4 Replacement Procedures 4.4 Bottom Cover

Installing the Bottom Cover

Install the Bottom cover with the display assembly according to the following procedures and

Figures 4-5, 4-6.

1. Hold up the bottom cover.

2. Connect the LED board cable from CN205.

3. Connect the RGB board cable from CN204.

4. Seat the bottom cover, adjusting its position.

5. Place the Left and right side hinge cover in the correct position.

6. Secure the following 13 screws on the bottom cover:

- Six M2.5x5 white flat head screws.

- Three M2x6 black flat head screws.

- Two M2.5x4 black flat head screws.

- Two M2.5x6 black flat head screws.

7. Stick following 9 seal tapes:

- Four seal tapes on front side.

- One seal tape on right side.

- Two seal tapes on rear side

- Two seal tapes on back side.

8. Place the bottom cover in the correct position and secure the following 15 latches, in that order:

- Four bottom latches on right sides.

- Two latches on right sides and three latches on left side.

- Six front latches.

9. Restore the normal computer placement then open the display panel and secure the following 6 screws:

- Five M2x6 black flat head screws.

- One M2x5 white flat head screw.

4-16 Satellite/E200/E205 Maintenance Manual

4.5 Display Assembly 4 Replacement Procedures

4.5 Display Assembly

Removing the Display Assembly

Remove the display assembly according to the following procedures and Figures 4-7.

1. Open the display panel at an angle of 90 degrees.

2. Turn the computer upside down.

3. Disconnect the CCD cable from CN2250 on the system board.

4. Disconnect the MIC cable from CN208 on the system board.

5. Disconnect the LCD cable from CN3000 on the system board.

6. Remove two M2.5x4 black flat head screws securing the LCD module to the top cover.

CN208

CN2250

CCD cable

CN3000

MIC cable

LCD cable

Figure 4-7 Removing the display assembly

Satellite/E200/E205 Maintenance Manual 4-17

4 Replacement Procedures 4.5 Display Assembly

Installing the Display Assembly

Install the display assembly according to the following procedures and Figures 4-7.

1. Place the display panel in the correct position.

2. Connect the CCD cable to CN2250 on the system board.

3. Connect the MIC cable to CN208 on the system board.

4. Connect the LCD cable to CN3000 on the system board.

5. Secure the display assembly with two M2.5x4 black flat head screws.

6. Close the display panel

4-18 Satellite/E200/E205 Maintenance Manual

4.6 Memory Module 4 Replacement Procedures

4.6 Memory Module

Removing the Memory Module

Remove the memory module according to the following procedures and Figures 4-8, after checking that the computer is turned off in boot mode.

CAUTION: Do not touch the connectors on the memory modules or in the computer.

Contaminated connectors can cause memory access problems.

Memory

Memory slot

Latches

Figure 4-8 Removing the memory module

1. Spread out the two memory lock latches so that the memory module pops up.

2. Pull the memory module up and out at an angle, using care to avoid touching the connectors.

Satellite/E200/E205 Maintenance Manual 4-19

4 Replacement Procedures 4.6 Memory Module

Installing the Memory Module

Install the memory module according to the following procedures and Figures 4-8, after checking that the computer is turned off in boot mode.

Note: The slot A is reserved for main memory. Use the slot B for expanded memory. If only one card is installed, use the slot A.

1. Insert the memory module into the connector at an angle of 45 degrees.

2. Press down on the memory module so that it is secured with both memory lock latches.

After the computer is turned on, check the hardware configuration in the Hardware Setup or

TSETUP program to make sure that the installed memory module has been recognized by the system. If it has not been recognized yet, check the connections

4-20 Satellite/E200/E205 Maintenance Manual

4.7 Wireless LAN Card 4 Replacement Procedures

4.7 Wireless LAN Card

Removing the Wireless LAN Card

Remove the wireless LAN card according to the following procedures and Figure 4-9.

CAUTION: Do not touch the connectors on the wireless LAN card and in the computer with your bare hands. Wireless LAN cards can fail if they are contaminated with sweat, natural oils, etc. from your hands.

1. Disconnect the two antenna cables with tweezers.

2. Remove the one M2x3 black flat head screw securing the wireless LAN card.

3. Pull the wireless LAN card up from CN1300 on the system board and out at an angle.

M2x3 black flat head screw

Black cable

White cable

Wireless LAN card

CN1300

Figure 4-9 Removing the wireless LAN card

Satellite/E200/E205 Maintenance Manual 4-21

4 Replacement Procedures 4.7 Wireless LAN Card

Installing the Wireless LAN Card

Install the wireless LAN card according to the following procedures and Figure 4-9.

1. Insert the wireless LAN card into the CN1300 an angle of 45 degrees.

2. Press down on the wireless LAN card to secure it with one M2x3 black flat head screw.

3. Connect the two antenna cables by pressing them firmly into place.

CAUTION: Do not touch the connectors on the wireless LAN card and in the computer with your bare hands. Wireless LAN cards can fail if they are contaminated with sweat, natural oils, etc. from your hands.

4-22 Satellite/E200/E205 Maintenance Manual

4.8 HDD 4 Replacement Procedures

4 1

4.8 HDD

Removing the HDD

CAUTION: Do not press on the top or bottom of the drive.

Applying such pressure can either corrupt the data in the drive or damage the drive.

Remove the HDD (hard disk drive) according to the following procedures and Figures 4-

10, 4-11.

1. Removing the two M2x3 black flat head screws.

M2x3 black flat head screw

HDD

Figure 4-10 Removing the HDD pack

Satellite/E200/E205 Maintenance Manual 4-23

4 Replacement Procedures

4.8 HDD

2. Remove the HDD pack by pulling on the tab attached to the pack.

NOTE: Do not disassemble the HDD pack when it is working normally. Disassemble or replace the HDD pack only if it fails.

3. Place the HDD pack on a flat surface (such as a desk), and remove the four M3x4 black flat head screws.

4. Place the HDD pack on a flat surface (such as a desk), and remove the chassis.

HDD

M3x4 black flat head screw

HDD chassis

M3x4 black flat head screw

Figure 4-11 Removing the HDD chassis

CAUTION: Do not apply pressure to the top or bottom of the drive.

4-24

Satellite/E200/E205 Maintenance Manual

4.8 HDD 4 Replacement Procedures

Installing the HDD

Install the HDD according to the following procedures and Figures 4-10, 4-11.

CAUTION: To avoid damage, always hold the HDD only by its sides.

1. Attach the HDD chassis.

2. Secure the HDD and its chassis with the four M3x4 black head screws.

CAUTION: To prevent the HDD bracket from being distorted when installing the HDD pack into the computer, do not press the center of the HDD pack. Always hold the HDD pack by its sides.

3. Install the HDD pack into the correct position in the computer. Connect the HDD pack to the computer, holding the HDD pack by its sides.

4. Insert the HDD pack.

5. Secure the HDD pack with two M2x3 black flat head screws.

Satellite/E200/E205 Maintenance Manual 4-25

4 Replacement Procedures 4.9 ODD Bay Module

4.9 ODD Bay Module

Removing the ODD Bay Module

NOTE: The installation and removal procedures are the same for all the modules that can be installed in the ODD bay. See the appropriate sections for the disassembly procedures of specific modules.

Remove the ODD bay module according to the following procedures and Figures 4-12.

1. Remove the three M2x3 black flat head screws.

2. Push out on the ODD bay module.

CAUTION: Handle the ODD bay module carefully it can become hot during operation.

M2x3 black flat head screw

ODD bay module

4-26

Figure 4-12 Removing the ODD bay module

Satellite/E200/E205 Maintenance Manual

4.9 ODD Bay Module 4 Replacement Procedures

Installing the ODD Bay Module

Install the ODD bay module according to the following procedures and Figures 4-12.

1. Place the ODD bay module in the correct position and slide it in.

2. Push it in until it clicks into place.

3. Secure the ODD bay module with three M2x3 black flat head screws.

Satellite/E200/E205 Maintenance Manual 4-27

4 Replacement Procedures 4.9 ODD Bay Module

Disassembling the ODD Drive

NOTE: Do not disassemble the ODD drive when it is working normally. Disassemble or replace the ODD drive only if it fails.

Disassemble the ODD drive according to the following procedures and Figure 4-13.

1. Remove four M2x3 black flat head screws.

2. Remove the two brackets.

3. Release the following 4 latches on the slot ODD bezel, in that order:

- Two above latches.

- Two below latches.

ODD

Latch

ODD bezel

M2x3 black flat head screw

ODD bracket

M2x3 black flat head screw

ODD side bracket

Figure 4-13 Removing the bracket from the ODD drive

Assembling the ODD Drive

Assemble the ODD drive according to the following procedures and Figure 4-13.

1. Place the slot ODD bezel in the correct position and secure the following 4 latches, in that order:

- Two above latches.

- Two below latches.

2. Seat the two brackets and secure it with four M2x3 black flat head screws.

4-28 Satellite/E200/E205 Maintenance Manual

4.10 Bluetooth Module 4 Replacement Procedures

4.10 Bluetooth module

Removing the Bluetooth module

NOTICE: Don’t touch the double tape surface for keep double tape surface clean and adhesive while remove the Bluetooth module from the ODD bracket.

Remove the Bluetooth module according to the following procedures and Figures 4-14.

1. Disconnect the Bluetooth cable from CN2150 on the system board.

2. Remove M1.6x2.5 white flat head screw.

3. Remove the Bluetooth module.

4. Disconnect the Bluetooth cable from the Bluetooth module. flat head screw

CN2150

Figure 4-14 Removing the Bluetooth module

Satellite/E200/E205 Maintenance Manual 4-29

4 Replacement Procedures 4.10 Bluetooth Module

Installing the Bluetooth Module

Install the Bluetooth module according to the following procedures and Figures 4-14.

1. Connect the Bluetooth cable to the Bluetooth module.

2. Place the Bluetooth module in the correct position.

3. Secure the Bluetooth module with M1.6x.2.5 white flat head screw.

4. Connect the Bluetooth cable to CN2150 on the system board.

4-30 Satellite/E200/E205 Maintenance Manual

4.11 CPU Cooling Module and Fan 4 Replacement Procedures

4.11 CPU Cooling Module and Fan

CAUTION: When removing the cooling module, keep the following in mind:

The cooling module can become very hot during operation. Be sure to let it cool down

before starting the repair work.

Do not touch or cause damage to the fan in the cooling module.

Remove the CPU cooling module and Fan

Remove the CPU cooling module and fan according to the following procedures and

Figures 4-15, 4-16, 4-17 and 4-18.

1. Disconnect the fan cable from CN4300 on system board.

2. Remove one M2x6 black flat head screw on the fan.

3. Remove the fan.

4. Release six CPU thermal securing screws on the CPU cooling module.

5. Remove the CPU cooling module.

M2x6 black flat head screw

CPU cooling module securing screw

Fan

CPU cooling module

Figure 4-15 Removing the fan and CPU cooling module

CN4300

Satellite/E200/E205 Maintenance Manual 4-31

4 Replacement Procedures 4.11 CPU Cooling Module and Fan

Figure 4-16 Applying silicon grease

Thermal pad

4-32

CPU cooling module

Figure 4-17 Replace new thermal pad into correct position.

Tape

Thermal pad

Figure 4-18 Tear down the tape.

Satellite/E200/E205 Maintenance Manual

4.11 CPU Cooling Module and Fan 4 Replacement Procedures

Installing the CPU Cooling Module and Fan

Install the cooling Module according to the following procedures and Figures 4-15, 4-16,

4-17 and 4-18.

CAUTION: When installing the cooling module, keep the following in mind:

1. Be sure to confirm the correct position for the module.

2. Secure the relevant screws on the main board according to the number sequence sealed on the heat sink module.

NOTE: Apply silicon grease with a special syringe to cover the surface of the CPU chip

completely.

1. If the thermal pad is broken, replace new thermal pad into correct position, thermal pad part number V000934140 for Mainz10 and V000941970 for Mainz10G.

2. If silicon grease is already applied to the CPU and fan module, wipe it off with a cloth.

By using a special syringe, apply silicon grease G7762 to the CPU chip center so that the entire CPU chip is covered with the grease G7762.

3. Install the CPU cooling module into the correct position on the system board.

4. Place the CPU cooling module in the correct position and secure it with six CPU thermal module securing screws.

5. Place the fan in the correct position and secure it with one M2x6 black flat head screw.

6. Connect the fan cable to CN4300 on the system board.

Satellite/E200/E205 Maintenance Manual 4-33

4 Replacement Procedures 4.12 CPU

4.12 CPU

Removing the CPU

CAUTION: When removing the CPU, keep the following in mind:

The CPU can become very hot during operation. Be sure to let it cool down before starting repair work.

Remove the CPU according to the following procedures and Figures 4-19, 4-20, 4-21 and

4-22.

NOTE: FOXCONN CPU socket will be 180 degrees to the right.

1. Unlock the CPU by rotating the cam on the CPU socket 120 degrees to the left with a flat-blade screwdriver (in the order shown in the figure below).

2. Remove the CPU.

3. Remove the CPU Mylar.

4-34

Figure4-19 Removing the CPU

CPU Mylar

CPU

Figure4-20 Removing the CPU Mylar

Satellite/E200/E205 Maintenance Manual

4.12 CPU 4 Replacement Procedures

Installing the CPU

Install the CPU according to the following procedures and Figures 4-20, 4-21 and 4-22.

1. Check that the triangle on the cam is in the unlock position.

2. Stick the CPU Mylar on the CPU.

3. Attach the CPU to the correct position in the CPU socket. Align the CPU with the

CPU socket by using the triangle as a guide.

Figure 4-21 Installing the CPU

CAUTION: Seat the CPU by aligning the triangle with the shaded area.

Satellite/E200/E205 Maintenance Manual 4-35

4 Replacement Procedures 4.12 CPU

4. Secure the CPU by rotating the cam 120 degrees to the right with a flat-blade screwdriver.

NOTE: FOXCONN CPU socket will be 180 degrees to the left.

Figure 4-22 Securing the CPU

4-36 Satellite/E200/E205 Maintenance Manual

4.13 System Board 4 Replacement Procedures

4.13 System Board

Removing the System Board

Remove the System Board according to the following procedures and Figure 4-23, 4-24.

1. Disconnect the light sensor cable from CN202 on system board.

2. Disconnect the RGB cable from CN3050 on system board.

3. Disconnect the RJ45 cable from CN470 on system board.

4. Disconnect the touch pad flat cable from CN280 on system board.

5. Disconnect the switch board cable from CN281 on system board.

6. Disconnect the finger print board cable from CN209 on system board.

7. Turn the top cover upside down.

8. Disconnect the audio board flat cable from CN201 on system board.

9. Disconnect the DC-IN cable from CN6000 on system board.

10. Disconnect the MMB board flat cable from CN200 on system board.

11. Remove three M2x3 black flat head screws.

12. Remove the system board.

Satellite/E200/E205 Maintenance Manual 4-37

4 Replacement Procedures

Light sensor cable

Touch pad flat cable

RGB cable

CN202

RJ45 cable

CN470

4.13 System Board

CN3050

CN281

CN280

CN209

Switch board flat cable

Finger print board cable

Figure 4-23 Disconnect from system board

M2x3 black flat head screw

System board

CN200

CN6000

CN201

Audio board flat cable

DC IN cable

MMB board flat cable

Figure 4-24 Removing the system board

4-38 Satellite/E200/E205 Maintenance Manual

4.13 System Board 4 Replacement Procedures

Installing the System Board

Note: Be careful of the Kill switch knob position for the kill switch. It can be damaged when installing the system board. Make sure its position is same as kill switch on system board..

Install the System Board according to the following procedures and figure 4-23, 4-24.

1. Seat the system board in the correct position.

2. Secure the system board with three M2x3 black flat head screws.

3. Connect the audio board flat cable from CN201 on system board.

4. Connect the DC-IN cable from CN6000 on system board.

5. Connect the MMB board flat cable from CN200 on system board.

6. Restore the normal top cover placement.

13. Connect the light sensor cable from CN202 on system board.

14. Connect the RGB cable from CN3050 on system board.

15. Connect the RJ45 cable from CN470 on system board.

16. Connect the touch pad flat cable from CN280 on system board.

17. Connect the switch board cable from CN281 on system board.

7. Connect the finger print board cable from CN209 on system board.

Satellite/E200/E205 Maintenance Manual 4-39

4-40

4 Replacement Procedures 4.14 Speakers

4.14 Speakers

Removing the Speakers

Remove the Speakers according to the following procedures and Figure 4-25.

1. Remove five M2x3 black flat head screws and two M2x2.5 black flat head screws from shield.

2. Remove the shield.

3. Disconnect the speaker cable from CN9801 on the audio board.

4. Remove two M2x3 black flat head step screw securing the left speaker.

5. Remove two M2x3 black flat head step screws securing the right speaker.

6. Remove the left and right speakers.

M2x3 black flat head screw

M2x3 black flat head step screw flat head screw

M2x3 black flat head screw

M2x3 black flat head step screw

Right speaker

Shield Left cable

Figure 4-25 Removing the speakers

CN9801

Satellite/E200/E205 Maintenance Manual

4.14 Speakers 4 Replacement Procedures

Installing the Speakers

Install the speakers according to the following procedures and Figure 4-25.

1. Seat the left and right speaker in the correct position.

2. Route the speaker cable in the wire guide.

3. Secure the left speaker with two M2x3 black flat head step screws.

4. Secure the right speaker with two M2x3 black flat head step screws.

5. Connect the speaker cable to CN9801 on the audio board.

6. Seat the left and right speaker in the correct position.

7. Seat the shield in the correct position.

8. Secure the shield with five M2x3 black flat head screws and two M2x2.5 black flat head screws.

Satellite/E200/E205 Maintenance Manual 4-41

4 Replacement Procedures 4.15 Switch Board and Finger Print Board

4.15 Switch Board and Finger Print Board

Removing Switch Board and Finger Print Board

Remove the Switch Board and Finger Print Board according to the following procedures and

Figure 4-26.

1. Remove one M2x3 black flat head screw securing the switch board.

2. Remove the switch board.

3. Disconnect the switch board flat cable from CN9400 on the switch board.

2. Remove the touch pad hold.

3. Remove the finger print board.

CN9400

Switch board flat cable

Switch board

Finger print board

M2x3 black flat head screw

Touch pad holder

Figure 4-26 Removing the switch board and finger print board

4-42

Satellite/E200/E205 Maintenance Manual

4.15 Switch Board and Finger Print Board 4 Replacement Procedures

Installing Switch Board and Finger Print Board

Install Switch Board and Finger Print Board to the following procedures and Figure 4-26.

1. Seat the finger print board in the correct position.

2. Seat the touch pad hold in the correct position.

3. Connect the switch board flat cable to CN9400 on the switch board.

4. Seat the switch board in the correct position.

5. Secure the switch board with one M2x3 black flat head screw.

Satellite/E200/E205 Maintenance Manual

4-43

4 Replacement Procedures 4.16 Light Sensor Board and Audio Board

4.16 Light Sensor Board and Audio Board

Removing the Light Sensor Board and Audio Board

Remove the Light Sensor Board and Audio Board according to the following procedures and

Figure 4-27.

1. Remove one M2x3 black flat head screw and remove the light sensor board.

2. Remove one M2x3 black flat head screw and remove the audio board.

3. Disconnect the audio board flat cable from CN9803 on the audio board.

Light sensor board

M2x3 black flat head screw

Audio board

Audio board flat cable

CN9803

Figure 4-27 Removing the touch pad and button board

4-44

Satellite/E200/E205 Maintenance Manual

4.16 Light Sensor Board and Audio Board 4 Replacement Procedures

Installing the Power Board, Switch Board and Logo LED Board

Install the Light Sensor Board and Audio Board according to the following procedures and

Figure 4-27.

1. Seat the light sensor board in the correct position and secure it with the one M2x3 black flat head screw.

2. Connect the audio board flat cable to CN9803 on the audio board.

3. Seat the audio board in the correct position and secure it with the two M2x3 black flat head screw.

Satellite/E200/E205 Maintenance Manual

4-45

4 Replacement Procedures 4.17 DC-IN cable, RGB Board and RJ45 cable

4.17 DC-IN cable, RGB Board and RJ45 cable

Removing DC-IN cable, RGB Board and RJ45 cable

Remove the DC-IN cable, RGB Board and RJ45 cable according to the following procedures and Figure 4-28.

1. Remove the DC-IN cable.

2. Remove two M2x3 black flat head screws securing the RGB board and one M2x3 black flat head screw securing the RGB cable.

3. Remove the RGB board.

4. Disconnect the RGB cable from CN9600 on the RGB board.

5. Remove two M2x3 black flat head screws securing the IO bracket and IO bracket cover.

6. Remove two M2x3 black flat head screws securing the IO bracket cover.

7. Remove the RJ45 cable.

RGB board cable

M2x3 black flat head screw

RJ45 cable

M2x3 black flat head screw

RGB board

IO bracket

IO bracket cover

Figure 4-28 DC-IN cable, RGB Board and RJ45 cable

4-46 Satellite/E200/E205 Maintenance

Manual

4.17 DC-IN cable, RGB Board and RJ45 cable 4 Replacement Procedures

Installing DC-IN cable, RGB Board and RJ45 cable

Install the DC-IN cable, RGB Board and RJ45 cable to the following procedures and Figure

4-28.

1. Seat the RJ45 cable in the correct position.

2. Seat IO bracket cover in the correct position of IO bracket, then secure it with two M2x3 black flat head screws

3. Seat IO bracket and IO bracket cover in the correct position of top cover then secure them with two M2x3 black flat head screws.

4. Seat the DC-IN cable in the correct position.

5. Seat the RGB board in the correct position.

6. Secure the RGB board with two M2x3 black flat head screws.

7. Connect the RGB cable to CN9600 on the RGB board.

8. Secure the RGB board cable with one M2x3 black flat head screw.

Satellite/E200/E205 Maintenance Manual

4-47

4 Replacement Procedures 4.18 Display Mask

4.18 Display Mask

Open Display Mask

Removing the Display Mask

Disassemble the display mask according to the following procedures and Figure 4-29.

1. Peel off four seal tapes and remove four M2.5x4 white flat head screws securing the display mask.

2. Insert your finger between the edge of display mask and the LCD and remove the display mask while unlatching the display mask.

Seal

Seal

Figure 4-29 Removing the display mask

Display mask

4-48 Satellite/E200/E205 Maintenance

Manual

4.18 Display Mask 4 Replacement Procedures

Installing the Display Mask

Install the display mask according to the following procedures and Figure 4-29.

1. Install the display mask and lock the latches.

NOTE: When installing the display mask, ensure there is no gap between the display mask and the display cover.

2. Secure the display mask with four 2.5x4 white flat head screws and stick four seal tapes on the front.

Satellite/E200/E205 Maintenance Manual

4-49

4 Replacement Procedures

4.19 LCD Module

4.19 LCD Module

NOTE: ICs are fragile. Use extreme care not to apply pressure to the ICs along the edges of the LCD module.

NOTE: Dispose of used LCD panels as required by local ordinances or regulations.

NOTE: The LCD cable must be carefully peeled away before disconnecting it from the module.

Open LCD module

Removing the LCD module

Remove the LCD module according to the following procedures and Figures 4-30, 4-31.

1. Remove the Left and right LCD hinge bracket cover.

2. Remove two M2.5x4 white flat head screws on each side securing the LCD bracket.

3. Carefully tilt the LCD module toward you.

4. Remove two M2x3 black flat head screws on each securing the LCD bracket.

5. Remove the LCD brackets.

6. Turn the LCD upside down. Be sure to place it on a cushioned surface such as a foam pad.

4-50 Satellite/E200/E205 Maintenance

Manual

4.19 LCD Module

Left LCD bracket

M2x3 black flat head screw

4 Replacement Procedures

LCD module

Right LCD bracket

Left LCD bracket cover

M2x3 black flat head screw

Right LCD bracket cover

Figure 4-30 Removing the LCD module and screws

7. Disconnect the LCD cable from LCD module.

LCD module

LCD cable

Figure 4-31 Removing the LCD module

Satellite/E200/E205 Maintenance Manual

4-51

4 Replacement Procedures 4.19 LCD Module

Installing the LCD Module

NOTE: LCD cable must be carefully peeled away before connecting it from the module.

Install the LCD module according to the following procedures and Figures 4-30, 4-31.

1. Turn the LCD upside down.

2. Connect the LCD cable to the LCD module connector.

3. Turn the LCD right side up.

4. Place the LCD bracket in the correct position and secure it with two M2x3 black flat head screws on each side.

5. Place the LCD module in the correct position and secure it with two M2.5x4 white flat heat screws on each side.

6. Place the LCD hinge bracket cover on correct position of LCD hinge.

CAUTION: When installing the LCD module, please follow below instruction:

When plug in LCD/FL cable into LCD module connector, need to plug horizontally. For

Sharp panel, if LCD/FL cable connector is not plugged horizontally, it may be damaged.

4-52 Satellite/E200/E205 Maintenance

Manual

4.19 LCD Module 4.20 CCD Board and MIC

4.20 CCD Board and MIC

Removing the CCD Board and MIC

Remove the FL inverter board according to the following procedures and Figure 4-32.

1. Remove the CCD module with CCD cable from display rear cover.

2. Disconnect the CCD cable from the CCD module connector.

CCD module

MIC cable

CCD cable

Display rear cover

Figure 4-32 Removing the CCD board and MIC

3. Lift the MIC from the display rear cover.

Satellite/E200/E205 Maintenance Manual

4-53

4 Replacement Procedures 4.20 CCD Board and MIC

Installing the CCD Board and MIC

Install the FL inverter board according to the following procedures and Figure 4-32.

1. Connect the CCD module cable to CCD module connector.

2. Seat the CCD module, MIC in the correct position.

4-54 Satellite/E200/E205 Maintenance

Manual

4.21 LED Board and Card Reader Board 4 Replacement Procedures

4.21 LED Board and Card Reader Board

Removing the LED Board and Card Reader Board

Remove the LED Board and Card Reader Board according to the following procedures and

Figure 4-33.

1. Remove two M2x3 black flat head screws and remove the LED lens.

2. Remove one M2x3 black flat head screw and remove the LED board.

3. Disconnect the LED board cable from CN9500 on the LED board.

4. Remove two M2x3 black flat head screws and remove the card reader board.

5. Disconnect the card reader board cable from CN9903 on the card reader board.

LED lens

M2x3 black flat head screw

LED board cable

CN9903

CN9500

LED board

Card reader board

Card reader board cable

M2x3 black flat head screw

Figure 4-33 Removing LED Board and card reader board

Satellite/E200/E205 Maintenance Manual

4-55

4 Replacement Procedures 4.21 LED Board and Card Reader Board

Installing the LED Board and Card Reader Board

Install the LED Board and Card Reader Board according to the following procedures and

Figure 4-33.

1. Connect the card reader board cable to CN9903 on the card reader board.

2. Seat the card reader board in the correct position and secure it with the two M2x3 black flat head screws.

3. Connect the LED board cable to CN9500 on the LED board.

4. Seat the LED board in the correct position and secure it with the one M2x3 black flat head screw.

5. Seat the LED lens in the correct position and secure it with the two M2x3 black flat head screws.

4-56 Satellite/E200/E205 Maintenance

Manual

6000 1

Appendices

Appendices

Appendix Contents

Appendix A Handling the LCD Module .......................................................................... A-1

Appendix B Board Layout .................................................................................................B-1

B.1

B.2

System Board Front View ......................................................................................B-1

System Board Back View ......................................................................................B-2

Appendix C .......................................................................................................................... C-2

C.1 CN200 Hot key Connector (6-Pin) ..............Error! Bookmark not defined.

C.2 CN201 Audio Connector (24-Pin) ...............Error! Bookmark not defined.

C.3 CN202 Light sensor BD Connector (4-Pin).Error! Bookmark not defined.

C.4 CN204 Card Reader Connector (8-Pin) .......Error! Bookmark not defined.

C.5 CN205 LED Connector (20-Pin)..................Error! Bookmark not defined.

C.6 CN208 Intermal Micro Phone Connector (2-Pin)...... Error! Bookmark not

defined.

C.7 CN209 Finger Print BD Connector (4-Pin) .Error! Bookmark not defined.

C.8 CN250 Keyboard Cable Connector (34-Pin)Error! Bookmark not defined.

C.9 CN251 Hot key BD Connector (4-Pin) ........Error! Bookmark not defined.

C.10 CN280 Touchpad Connector (6-Pin) ...........Error! Bookmark not defined.

C.11 CN281 Touchpad ON/OFF Connector (4-Pin) .......... Error! Bookmark not

defined.

C.12 CN470 RJ45 LAN Port Connector (12-Pin) Error! Bookmark not defined.

C.13 CN1300 Wireless LAN Module Connector (52-Pin)... Error! Bookmark not

defined.

C.14 CN1401 SIM Card Connector (6-Pin) ...........Error! Bookmark not defined.

C.15 CN1700 SATA HDD Connector (22-Pin) .....Error! Bookmark not defined.

C.16 CN1750 SATA ODD Connector (13-Pin) .....Error! Bookmark not defined.

C.17 CN1800 e-SATA Port Connector (11-Pin) ....Error! Bookmark not defined.

C.18 CN2000 USB#0 Connector (4-Pin)................Error! Bookmark not defined.

C.19 CN2150 Bluetooth Cable Connector (10-Pin)Error! Bookmark not defined.

C.20 CN2250 Camera Cable Connector (5-Pin).....Error! Bookmark not defined.

C.21 CN3000 LCD Cable Connector (40-Pin) .......Error! Bookmark not defined.

App-ii

Satellite E200/205 Maintenance Manual

Appendices

C.22 CN3050 RGB Connector (14-Pin) .................Error! Bookmark not defined.

C.23 CN3150 HDMI Port Connector (19-Pin ) .......Error! Bookmark not defined.

C.24 CN4100 DDR3 So-Dimm0 Connector (204-Pin) ......... Error! Bookmark not

defined.

C.25 CN4101 DDR3 So-Dimm1 Connector (204-Pin) ......... Error! Bookmark not

defined.

C.26 CN4300 FAN Connector (3-Pin) ....................Error! Bookmark not defined.

C.27 CN6000 DC-IN Cable Connector (4-Pin).......Error! Bookmark not defined.

C.28 CN6970 Battery Connector (9-Pin).................Error! Bookmark not defined.

C.29 CN9400 Touchpad ON/OFF BD Connector (4-Pin)..... Error! Bookmark not

defined.

C.30 CN9500 LED BD Connector (20-Pin) ........................................................ C-19

C.31 CN9600 RGB BD Connector (14-Pin)......................................................... C-20

C.32 CN9601 RGB BD to MB Connector (15-Pin) ............................................. C-20

C.33 CN9801 Speaker Connector (4-Pin) ............................................................ C-21

C.34 CN9802 USB#1 Connector (4-Pin).............................................................. C-21

C.35 CN9803 Audio BD Connector (24-Pin)....................................................... C-21

C.36 CN9900 Card Reader BD Connector (38-Pin)............................................. C-22

C.37 CN9903 Card Reader BD to MB Connector (8-Pin) ................................... C-22

C.38 JACK9800 SPDIF/ Head Phone Connect (6-Pin)............................................ C-23

C.39 JACK9801 Ezternal MIC Connector (6-Pin) ................................................... C-23

Appendix D Keyboard Scan/Character Codes................................................................ D-1

Appendix E Key Layout .................................................................................................... E-1

Satellite E200/205 Maintenance

Manual

App-iii

Apx. A Handling the LCD Module Appendices

Appendix A

Appendix A Handling the LCD Module

Precautions for handling the LCD module

The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling the LCD module:

1. When installing the LCD module in the LCD cover, be sure to seat it so that it is properly aligned and maximum visibility of the display is maintained.

2. Be careful to align the four holes at the right side and left side of the LCD module with the corresponding holes in the LCD cover before securing the module with four screws. Do not force the module into place, because stress can affect its performance.

Also, the panel’s polarized surface is easily scarred, so be carefully when handling it.

Satellite E200/205 Maintenance Manual

A-1

Appendices

Apx. A Handling the LCD Module

3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again.

If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface. Do not apply cleanser directly to the panel.

Also, never scratch the surface.

4. If water or other liquid is left on the panel’s surface for a long period, it can change the screen’s tint or stain it. Be sure to quickly wipe off any liquid.

A-2

Satellite E200/205 Maintenance Manual

Apx. A Handling the LCD Module Appendices

5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks.

6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module.

Satellite E200/205 Maintenance Manual

A-3

Appendices

Apx. A Handling the LCD Module

7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods.

8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage.

A-4

Satellite E200/205 Maintenance Manual

Apx. A Handling the LCD Module Appendices

9. Do not disassemble the LCD module. Disassembly can cause malfunctions.

10. If you transport the module, do not use packing material that contains epoxy resin

(amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel’s polarization.

Satellite E200/205 Maintenance Manual

A-5

Apx. B Board Layout

Appendix B

Appendix B Board Layout

B.1 System Board Front View

Appendices

Figure B-1 Board layout (front)

Satellite E200/205 Maintenance Manual B-1

Appendices

B.2 System Board Back View

Apx. B Board Layout

B-2

Figure B-2 Board layout (back)

Satellite E200/205 Maintenance Manual

Appendices

Apx. C Pin Assignments

Appendix C C-3

C.1 CN200 Hot key Connector (6-Pin) ..........................................................C-12

C.2 CN201 Audio Connector (24-Pin).............................................................C-5

C.3 CN202 Light sensor BD Connector (4-Pin) ..............................................C-3

C.4 CN204 Card Reader Connector (8-Pin).....................................................C-6

C.5 CN205 LED Connector (20-Pin) ...............................................................C-7

C.6 CN208 Intermal Micro Phone Connector (2-Pin)......................................C-4

C.7 CN209 Finger Print BD Connector (4-Pin) .............................................C-10

C.8 CN250 Keyboard Cable Connector (34-Pin).............................................C-5

C.9 CN251 Hot key BD Connector (4-Pin)......................................................C-4

C.10 CN280 Touchpad Connector (6-Pin).......................................................C-10

C.11 CN281 Touchpad ON/OFF Connector (4-Pin)..........................................C-9

C.12 CN470 RJ45 LAN Port Connector (12-Pin)............................................C-11

C.13 CN1300 Wireless LAN Module Connector (52-Pin) ..................................C-5

C.14 CN1401 SIM Card Connector (6-Pin) .........................................................C-6

C.15 CN1700 SATA HDD Connector (22-Pin)...................................................C-3

C.16 CN1750 SATA ODD Connector (13-Pin)...................................................C-4

C.17 CN1800 e-SATA Port Connector (11-Pin)................................................C-11

C.18 CN2000 USB#0 Connector (4-Pin) .............................................................C-9

C.19 CN2150 Bluetooth Cable Connector (10-Pin).............................................C-9

C.20 CN2250 Camera Cable Connector (5-Pin) ..................................................C-8

C.21 CN3000 LCD Cable Connector (40-Pin).....................................................C-8

C.22 CN3050 RGB Connector (14-Pin).............................................................C-12

C.23 CN3150 HDMI Port Connector (19-Pin )....................................................C-7

C.24 CN4100 DDR3 So-Dimm0 Connector (204-Pin)......................................C-15

C.25 CN4101 DDR3 So-Dimm1 Connector (204-Pin)......................................C-18

C.26 CN4300 FAN Connector (3-Pin)...............................................................C-19

C.27 CN6000 DC-IN Cable Connector (4-Pin) .................................................C-19

C.28 CN6970 Battery Connector (9-Pin) ...........................................................C-19

C.29 CN9400 Touchpad ON/OFF BD Connector (4-Pin) .................................C-20

C.30 CN9500 LED BD Connector (20-Pin).......................................................C-19

Satellite E200/205 Maintenance Manual

C-1

Appendices

Apx. C Pin Assignments

C.31 CN9600 RGB BD Connector (14-Pin) ..........................................................C-20

C.32 CN9601 RGB BD to MB Connector (15-Pin)...............................................C-20

C.33 CN9801 Speaker Connector (4-Pin) ..............................................................C-21

C.34 CN9802 USB#1 Connector (4-Pin) ...............................................................C-21

C.35 CN9803 Audio BD Connector (24-Pin) ........................................................C-21

C.36 CN9900 Card Reader BD Connector (38-Pin) ..............................................C-22

C.37 CN9903 Card Reader BD to MB Connector (8-Pin).....................................C-22

C.38 JACK9800 SPDIF/ Head Phone Connect (6-Pin) .............................................C-23

C.39 JACK9801 Ezternal MIC Connector (6-Pin).....................................................C-23

C-2

Satellite E200/205 Maintenance Manual

Appendices

Appendix C

Appendix C Pin Assignments

Apx. C Pin Assignments

System Board

C.1 CN200 Hot key Connector (6-Pin)

Table C-1 Hot key Connector pin assignments (6-Pin)

Pin No Signal Name I/O Pin No.

1

3

+V3LA -

HOTKEY_INT# O

2

4

5 EC_SMB3_DATA O

G1 DGND -

6

G2

Signal Name

+V5A

DGND

EC_SMB3_CLK

DGND

I/O

O

-

-

-

C.2 CN201 Audio Connector (24-Pin)

Table C-2 Audio Connector pin assignments (24-Pin)

Pin No.

1

3

5

7

9

Signal Name

MIC_IN

PCSPKR

DGND

USB_P_P2

SB_USB_1

I/O Pin No.

O 2

O 4

- 6

I/O

8

O 10

Signal Name

DGND

MMB_BEEP

USB_N_P2

DGND

USB_OC#_1

11 DGND - 12 AC97_3S_BITCLK O

13 AC97_3S_RST# O 14 AC97_3S_SYNC O

15 AC97_3S_SDIN0 I 16 AC97_3S_SDOUT O

17 AMP_SHUTDOWN O 18 +V3S -

19

21

+V3S

+V5A

- 20

- 22

+V5A

+V5A

-

-

-

I

I/O

-

O

I/O

Satellite E200/205 Maintenance Manual

C-3

Appendices

Apx. C Pin Assignments

23

G1

+V5A

DGND

- 24

- G2

+V5A

DGND

-

-

C.3 CN202 Light sensor BD Connector (4-Pin)

Table C-3 Light sensor BD Connector pin assignments (4-Pin)

Pin No.

1

Signal Name

+V3S

I/O Pin No.

- 2

3 EC_SMB3_DATA O

G1 DGND -

4

G2

Signal Name

EC_SMB3_CLK

DGND

DGND

I/O

O

-

-

C.4 CN204 Card Reader Connector (8-Pin)

Table C-4 Card Reader Connector pin assignments (8-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

3

CLK_IC_CARDREADE

R

O 4

5 LED_CARDREADER I 6

DGND

DGND

-

-

7 USB_N_CARDREADER I/O

C.5 CN205 LED Connector (20-Pin)

Table C-5 LED Connector pin assignments (20-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

3 WIRELESS_LED# O 4 WIMAX_3G_LED# O

7 LED_3S_SATA# O 8 +V3A -

9 EC_PWR_OLED# O 10 PWR_BLED# O

C-4

Satellite E200/205 Maintenance Manual

Appendices

Apx. C Pin Assignments

11 BAT_OLED# O +V3LA -

19 DGND -

C.6 CN208 Internal Micro Phone Connector (2-Pin))

Table C-6 Internal Micro Phone Connector pin assignments (2-Pin)

Pin No. Signal Name I/O Pin No.

1 MIC_IN I

Signal Name I/O

2 DGND -

C-7 CN209 Finger Print BD Connect (4-Pin)

Table C-7 Finger Print Board Connect pin assignments (4-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

I/O DGND -

C.8 CN250 keyboard cable connector (34-Pin)

Table C-8 keyboard cable connector pin assignments (34-Pin)

Pin No. Signal Name I/O Pin No.

1 +V3S -

Signal Name I/O

2 SCAN_OUT(16) I

Satellite E200/205 Maintenance Manual

C-5

Appendices

Apx. C Pin Assignments

13 SCAN_OUT(11) I 14 SCAN_OUT(9) I

17 SCAN_OUT(10) I 18 SCAN_OUT(14) I

33 SCROLL_LED#_3 I 34 NUM_LED#_3 I

C.9 CN251 Hot key BD Connector (4-Pin)

Table C-9 Hot key BD Connector pin assignments (4-Pin)

Pin No. Signal Name I/O Pin No.

1 DGND -

Signal Name I/O

2 DGND -

C.10 CN280 Touchpad Connector (6-Pin)

Table C-10 Touchpad Connector pin assignments (6-Pin)

Pin No. Signal Name I/O Pin No.

1 +V5S -

Signal Name I/O

2 IM_CLK_5 I/O

5 RIGHT_TP I DGND -

C-6

Satellite E200/205 Maintenance Manual

Appendices

Apx. C Pin Assignments

C.11 CN281 Touchpad ON/OFF Connector (4-Pin)

Table C-11 Touchpad ON/OFF Connector pin assignments (4-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

G1 DGND G2 DGND -

C.12 CN470 RJ45 LAN Port Connector (12-Pin)

Table C-12 RJ45 LAN Port Connector pin assignments (12-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

11 LED_R3S_LANLINK# I 12 LED_R3S_LANACT I

C.13 CN1300 Wireless LAN Module Connector (52-Pin)

Table C-13 Wireless LAN Module Connector pin assignments (52-Pin)

Pin No.

1

Signal Name I/O Pin No.

Signal Name I/O

I/O -

7 CLKREQ_WLAN# O 8 LPC_3S_FRAME# O

11 CLK_PCIE_WLAN# O 12 LPC_3S_AD(2) O

13 CLK_PCIE_WLAN O 14 LPC_3S_AD(1) O

17 PLT_RST# O DGND -

Satellite E200/205 Maintenance Manual

C-7

Appendices

Apx. C Pin Assignments

19 CLK_R_PCI_DEBUG O 20 WXMIT_OFF# O

23 PCIE_C_RXN_WLAN I 24

25 PCIE_C_RXP_WLAN I 26

+V3S

DGND

-

-

31 PCIE_C_TXN_WLAN O 32 PCH_3A_ALERT_DAT I/O

33 PCIE_C_TXP_WLAN O 34 DGND -

43 DGND - - -

45 - 46 - -

51 PCI_3S_SERIRQ O 52 +V3S -

C.14 CN1401 SIM Card Connector (6-Pin)

Table C-14 SIM Card Connector pin assignments (6-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

P3 UIM_CLK I/O -

C.15 CN1700 SATA HDD Connector (22-Pin)

Table C-15 SATA HDD Connector pin assignments (22-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

C-8

Satellite E200/205 Maintenance Manual

Appendices

Apx. C Pin Assignments

3 SATA_C_TXN_HDD O 4 DGND -

5 SATA_RXN_HDD I 6 SATA_RXP_HDD I

7 DGND - - -

17 DGND - - -

19 DGND - - -

C.16 CN1750 SATA ODD Connector (13-Pin)

Table C-16 SATA ODD Connector pin assignments (13-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

S3 SATA_C_TXN_ODD O S4 DGND -

S5 SATA_RXN_ODD I S6 SATA_RXP_ODD I

S7 DGND - - -

- -

C.17 CN1800 e-SATA Port Connector (11-Pin)

Table C-17 e-SATA Port Connector pin assignments (11-Pin)

Pin No. Signal Name

7 SATA_IC_C_TXN_ESAT

I/O Pin No.

Signal Name I/O

2 USB_L_N_P1

I/O DGND -

O 8

A

DGND

O

-

Satellite E200/205 Maintenance Manual

C-9

Appendices

Apx. C Pin Assignments

A

9 SATA_RXN_ESATA I 10 SATA_RXP_ESATA I

11 DGND - - -

C.18 CN2000 USB#0 Connector (4-Pin)

Table C-18 USB#0 Connector pin assignments (4-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

I/O DGND -

C.19 CN2150 Bluetooth Cable Connector (10-Pin)

Table C-19 Bluetooth Cable Connector pin assignments (10-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

I/O DGND -

C.20 CN2250 Camera Cable Connector (5-Pin)

Table C-20 Camera Cable Connector pin assignments (5-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

I/O DGND -

C-10

Satellite E200/205 Maintenance Manual

Appendices

Apx. C Pin Assignments

5 DGND - - -

C.21 CN3000 LCD Cable Connector (40-Pin)

Table C-21 LCD Cable Connector pin assignments (40-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

1 DGND

3 DGND

5 DGND

7 LVDS_TXDL0N

-

-

-

O

2 LCM_VDDEN

O

4 LCM_VDDEN

O

6 +V3S

-

8 LVDS_TXDL1N

O

9 LVDS_TXDL0P

O

10 LVDS_TXDL1P

O

11 LVDS_TXDL2N

O

12 LVDS_TXCLN

O

27 LVDS_R_DDCCLK I/O 28 LVDS_R_DDCDATA I/O

C.22 CN3050 RGB Connector (14-Pin)

Table C-22 RGB Connector pin assignments (14-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

Satellite E200/205 Maintenance Manual

C-11

Appendices

Apx. C Pin Assignments

1 +VDD_CRT2 - CRTR_R O

5 DGND -

13 CRT_DDCCLK_OUT I/O 14 - -

C.23 CN3150 HDMI Port Connector (19-Pin))

Table C-23 HDMI Port Connector pin assignments (19-Pin)

Pin No. Signal Name I/O Pin No.

3 HDMI_L_TX2N O

Signal Name I/O

DGND -

4 HDMI_L_TX1P O

DGND -

- -

15 HDMI_DDCCLK_CN O 16 HDMI_DDCDATA_CN O

19 HDMI_HPD_5R I - - -

C.24 CN4100 DDR3 So-DImm0 Connector (204-Pin)

Table C-24 DDR3 So-DImm0 Connector pin assignments (204-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

C-12

Satellite E200/205 Maintenance Manual

Appendices

Apx. C Pin Assignments

I/O DGND -

47 M_A_DQS(2) O DGND -

53 M_A_DQ(19) I/O DGND -

59 M_A_DQ(25) I/O DGND -

Satellite E200/205 Maintenance Manual

C-13

Appendices

Apx. C Pin Assignments

115 M_A_CAS# O O

121 M_CS#1 O - -

135 M_A_DQS#(4) O O

137 M_A_DQS(4) O DGND -

143 M_A_DQ(35) I/O DGND -

149 M_A_DQ(41) I/O DGND -

C-14

Satellite E200/205 Maintenance Manual

Appendices

Apx. C Pin Assignments

169 M_A_DQS#(6) O O

171 M_A_DQS(6) O DGND -

177 M_A_DQ(51) I/O DGND -

183 M_A_DQ(57) I/O DGND -

C.25 CN4101 DDR3 So-DImm1 Connector (204-Pin)

Table C-25 DDR3 So-DImm1 Connector pin assignments (204-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

Satellite E200/205 Maintenance Manual

C-15

Appendices

Apx. C Pin Assignments

I/O DGND -

47 M_B_DQS(2) O DGND -

53 M_B_DQ(19) I/O DGND -

59 M_B_DQ(25) I/O DGND -

C-16

Satellite E200/205 Maintenance Manual

Appendices

Apx. C Pin Assignments

121 M_CS#3 O - -

135 M_B_DQS#(4) O O

137 M_B_DQS(4) O DGND -

143 M_B_DQ(35) I/O DGND -

Satellite E200/205 Maintenance Manual

C-17

Appendices

Apx. C Pin Assignments

149 M_B_DQ(41) I/O DGND -

169 M_B_DQS#(6) O O

171 M_B_DQS(6) O DGND -

177 M_B_DQ(51) I/O DGND -

183 M_B_DQ(57) I/O DGND -

C.26 CN4300 FAN Connector (3-Pin)

Table C-26 FAN Connector pin assignments (3-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

1 +FAN_VDD - DGND -

C-18

Satellite E200/205 Maintenance Manual

Appendices

Apx. C Pin Assignments

- -

C.27 CN6000 DC-IN Cable Connector (4-Pin)

Table C-27 DC-IN Cable Connector pin assignments (4-Pin)

Pin No. Signal Name I/O Pin No.

1 +VADPTR -

Signal Name I/O

2 +VADPTR -

C.28 CN6970 Battery Connector (9-Pin)

Table C-28 Battery Connector pin assignments (9-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

8 DGND -

9 DGND - - -

C.29 CN9400 Touchpad ON/OFF BD Connector (4-Pin)

Table C-29 Touchpad ON/OFF BD Connector pin assignments (4-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

Satellite E200/205 Maintenance Manual

C-19

Appendices

Apx. C Pin Assignments

C.30 CN9500 LED BD Connector (20-Pin)

Table C-30 LED BD Connector pin assignments (20-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

3 WIRELESS_LED#_DB I 4 WIMAX_3G_LED#_DB I

9 EC_PWR_OLED#_L I 10 PWR_BLED#_L I

11 BAT_OLED#_L I

+V3LA+LED -

13 BAT_BLED1#_L I 14 DCIN_BLED#_L I

C.31 CN9600 RGB BD Connector (14-Pin)

Table C-31 RGB BD Connector pin assignments (14-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

1 +VDD_CRT2_DB - 2 CRTR_R_DB I

11 - - I/O

13 CRT_DDCCLK_OUT_DB I/O 14 - -

C.32 CN9601 RGB BD to MB Connector (15-Pin)

Table C-32 RGB BD to MB Connector pin assignments (15-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

C-20

Satellite E200/205 Maintenance Manual

Appendices

Apx. C Pin Assignments

3 CRTB_R_DB O 4 - -

9 +VDD_CRT2_DB - GND_CRT -

11 - - I/O

13 CRT_HSYNC_OUT_DB O 14 CRT_VSYNC_OUT_DB O

15 CRT_DDCCLK_OUT_DB I/O - - -

C.33 CN9801 Speaker Connector (4-Pin)

Table C-33 Speaker Connector pin assignments (4-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

1 SPK_OUT_L+_DB O 2 SPK_OUT_L-_DB O

3 SPK_OUT_R-_DB O 4 SPK_OUT_R+_DB O

C.34 CN9802 USB#1 Connector (4-Pin)

Table C-34 USB#1 Connector pin assignments (4-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

C.35 CN9803 Audio BD Connector (24-Pin)

Table C-35 Audio BD Connector pin assignments (24-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

Satellite E200/205 Maintenance Manual

C-21

Appendices

Apx. C Pin Assignments

9 AC97_3S_SDOUT_DB I 10 AC97_3S_SDIN0_DB O

11 AC97_3S_SYNC_DB I 12 AC97_3S_RST#_DB I

13 AC97_3S_BITCLK_DB I 14 GND_AUDIO -

15 USB_OC#_1_DB O 16 SB_USB_1_DB I

21 MMB_BEEP_DB I I

C.36 CN9900 Card Reader BD Connector (38-Pin)

Table C-36 Card Reader BD Connector pin assignments (38-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

I/O MS_INS# I/O

I/O SD_CD# I/O

11 SD_D3_MS_D1 I/O SD_CMD I/O

25 SD_D0_MS_D7 I/O SD_CMD I/O

C-22

SD_CD# I/O

Satellite E200/205 Maintenance Manual

Appendices

Apx. C Pin Assignments

C.37 CN9903 Card Reader BD to MB Connector (8-Pin)

Table C-37 Card Reader BD to MB Connector pin assignments (8-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

3 CLK_R_CARDREADER_DB I 4 GND_CARD

5 LED_CARDREADER_DB O 6

7

USB_N_CARDREADER_D

B

GND_CARD

USB_P_CARDREADER_D

B

-

-

I

C.38 JACK9800 SPDIF/ Head Phone Connector (6-Pin)

Table C-38 SPDIF/ Head Phone Connector pin assignments (6-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

1 ANAGND -

5 ANAGND - - -

C.39 JACK9801 External MIC Connector (6-Pin)

Table C-39 External MIC Connector pin assignments (6-Pin)

Pin No. Signal Name I/O Pin No.

Signal Name I/O

I/O - -

Satellite E200/205 Maintenance Manual

C-23

Keyboard Scan/Character Codes Appendices

Apx. D Keyboard Scan/Character Codes

Appendix D Keyboard Scan/Character Codes

Cap

No.

07

08

09

10

11

12

13

01

02

03

04

05

06

Table D-1 Scan codes (set 1 and set 2) (1/4)

Code set 1 Code set 2

Keytop

Make Break Make Break

6 ^

7 &

8 *

9 (

0 )

- _

= +

‘ ~

1 !

2 @

3 #

4 $

5 %

29

02

03

04

05

06

07

08

09

0A

0B

0C

0D

A9

82

83

84

85

86

87

88

89

8A

8B

8C

8D

0E

16

1E

26

25

2E

36

3D

3E

46

45

4E

55

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

*2

*2

*2

*2

36

3D

3E

46

45

4E

55

0E

16

1E

26

25

2E

Note

15 BkSp 0E 8E 66 F0 66

17 Q 10 90 15 F0 15

19 E 12 92 24 F0 24

22 Y 15 95 35 F0 35

24 I 17 97 43 F0 43 *2

25 O 18 98 44 F0 44 *2

27

28

[ {

] }

1A

1B

9A

9B

54

5B

F0

F0

54

5B

Satellite E200/205 Maintenance Manual D-1

Appendices Keyboard Scan/Character Codes

Table D-1 Scan codes (set 1 and set 2) (2/4)

Cap

No.

Code set 1 Code set 2

Keytop

Make Break Make Break

Note

29 \ | 2B AB 5D F0 5D *5

30 Caps

33 D 20 A0 23 F0 23

35 G 22 A2 34 F0 34

36 H 23 A3 33 F0 33

38 K 25 A5 42 F0 42 *2

40

41

; :

‘ “

27

28

A7

A8

4C

52

F0

F0

4C

52

*2

45 No.102 key

56 D6 61 F0 61

D-2

50 B 30 B0 32 F0 32

51 N 31 B1 31 F0 31

53

54

55

56

, <

. >

/ ?

\_

33

34

35

B3

B4

B5

41

49

4A

F0

F0

F0

41

49

4A

*2

*2

*2

Satellite E200/205 Maintenance Manual

Keyboard Scan/Character Codes Appendices

Cap

No. Keytop

Table D-1 Scan codes (set 1 and set 2) (3/4)

Code set 1 Code set 2

Make Break Make Break

Note

112

113

114

115

116

117

118

119

120

121

62 ALT

75

76

Ins

Del

E0 52 E0 D2 E0 70 E0 F0 70 *1

E0 53 E0 D3 E0 71 E0 F0 71 *1

79

80

81

 E0 4B E0 CB E0 6B E0 F0 6B *1

Home E0 47 E0 C7 E0 6C E0 F0 6C *1

End E0 4F E0 CF E0 69 E0 F0 69 *1

83

84





E0 48 E0 C8 E0 75 E0 F0 75 *1

E0 50 E0 D0 E0 72 E0 F0 72 *1

85

86

PgUp E0 49 E0 C9 E0 7D E0 F0 7D *1

PgDn E0 51 E0 D1 E0 7A E0 F0 7A *1



E0 4D E0 CD E0 74 E0 F0 74 *1 89

110 Esc 01 81 76 76

F6

F7

F8

F9

F1

F2

F3

F4

F5

F10

3B

3C

3D

3E

3F

40

41

42

43

44

BB

BC

BD

BE

BF

C0

C1

C2

C3

C4

05

06

04

0C

03

0B

83

0A

01

09

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

05

06

04

0C

03

0B

83

0A

01

09 *3

Satellite E200/205 Maintenance Manual D-3

Appendices Keyboard Scan/Character Codes

Table D-1 Scan codes (set 1 and set 2) (4/4)

Cap Code set 1 Code set 2 Note

No. Keytop Make Break Make Break

122 F11 78 *3

205 Kat/Hir

206 Hen

207 Muh 7B F0 7B *8

Notes:

1. * Scan codes differ by mode.

2. * Scan codes differ by overlay function.

3. * Combination with the Fn key makes different codes.

4. * Fn key does not generate a code by itself.

5. * This key corresponds to key No. 42 in a 102-key model.

6. * Refer to Table D-6, No. 124 key scan code.

7. * Refer to Table D-7, No. 126 key scan code.

8. * 205~207 are for JAPAN keyboard only

D-4 Satellite E200/205 Maintenance Manual

Keyboard Scan/Character Codes Appendices

Table D-2 Scan codes with left Shift key

Cap

No.

Key top

Code set 1

Make Break

Code set 2

Make Break

55 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12

75 INS E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12

76 DEL E0 AA E0 53 E0 D3 E0 2A E0 F0 12 E0 71 E0 F0 71 E0 12

79  E0 AA E0 4B E0 CB E0 2A E0 F0 12 E0 6B E0 F0 6B E0 12

80 Home E0 AA E0 47 E0 C7 E0 2A E0 F0 12 E0 6C E0 F0 6C E0 12

81 End E0 AA E0 4F E0 CF E0 2A E0 F0 12 E0 69 E0 F0 69 E0 12

83

84





E0 AA E0 48 E0 C8 E0 2A E0 F0 12 E0 75 E0 F0 75 E0 12

E0 AA E0 50 E0 D0 E0 2A E0 F0 12 E0 72 E0 F0 72 E0 12

85 PgUp E0 AA E0 49 E0 C9 E0 2A E0 F0 12 E0 7D E0 F0 7D E0 12

86 PgDn E0 AA E0 51 E0 D1 E0 2A E0 F0 12 E0 7A E0 F0 7A E0 12

89  E0 AA E0 4D E0 CD E0 2A E0 F0 12 E0 74 E0 F0 74 E0 12

203 Win E0 AA E0 5B E0 DB E0 2A E0 F0 12 E0 1F E0 F0 1F E0 12

204 App E0 AA E0 5D E0 DD E0 2A E0 F0 12 E0 2F E0 F0 2F E0 12

Note : The table above shows scan codes with the left Shift key. In combination with the right Shift key, scan codes are changed as listed below:

Set 1

Set 2

E0 AA __________ E0 B6

E0 2A ___________ E0 36

E0 F0 12 ________ E0 F0 59

E0 12 ___________ E0 59

Satellite E200/205 Maintenance Manual D-5

Appendices Keyboard Scan/Character Codes

Table D-3 Scan codes in Numlock mode

Cap

No.

Key top

Code set 1 Code set 2

Make Break Make Break

75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12

76 DEL E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12

79



E0 2A E0 4B E0 CB E0 AA E0 12 E0 6B E0 F0 6B E0 F0 12

80 Home E0 2A E0 47 E0 C7 E0 AA E0 12 E0 6C E0 F0 6C E0 F0 12

81 End E0 2A E0 4F E0 CF E0 AA E0 12 E0 69 E0 F0 69 E0 F0 12

83

84





E0 2A E0 48 E0 C8 E0 AA E0 12 E0 75 E0 F0 75 E0 F0 12

E0 2A E0 50 E0 D0 E0 AA E0 12 E0 72 E0 F0 72 E0 F0 12

85 PgUp E0 2A E0 49 E0 C9 E0 AA E0 12 E0 7D E0 F0 7D E0 F0 12

86 PgDn E0 2A E0 51 E0 D1 E0 AA E0 12 E0 7A E0 F0 7A E0 F0 12

89  E0 2A E0 4D E0 CD E0 AA E0 12 E0 74 E0 F0 74 E0 F0 12

203 Win E0 2A E0 5B E0 DB E0 AA E0 12 E0 1F E0 F0 1F E0 F0 12

204 App E0 2A E0 5D E0 DD E0 AA E0 12 E0 2F E0 F0 2F E0 F0 12

Table D-4 Scan codes with Fn key

Cap

No. Keytop

Code set 1 Code set 2

Make Break Make Break

43 ENT E0 1C E0 9C E0 5A

58 CTRL E0 1D E0 9D E0 14 E0 F0 14

60 LALT E0 38 E0 B8 E0 11 E0 F0 11

121 ARROW 45 C5 77 F0 77

122 NUMERIC

123 Scrl

45

46

C5

C5

77

7E

F0 77

F0 7E

D-6 Satellite E200/205 Maintenance Manual

Keyboard Scan/Character Codes Appendices

Table D-5 Scan codes in overlay mode

Cap

No.

Keytop Code set 1 Code set 2

Make Break Make Break

08 7 (7) 47

09 8 (8) 48

10 9 (9) 49

11 0 (*) 37

23 U (4) 4B

24 I (5) 4C

25 O (6) 4D

26 P (–) 4A

37 J (1) 4F

38 K (2) 50

39 L (3) 51

40 ; (+) 4E

52 M (0) 52

54 . (.) 53

C7

C8

C9

B7

CB

CC

CD

CA

CF

D0

D1

CE

D2

D3

6C

75

7D

7C

6B

73

74

7B

69

72

7A

79

70

71

F0

F0

F0

F0

F0

F0 73

F0

F0

F0

F0

F0

F0 79

F0

6C

75

7D

7C

6B

74

7B

69

72

7A

70

F0 71

Table D-6 No.124 key scan code

Key top

Shift Code set 1 Code set 2

Make Break Make Break

Prt E0 12 E0 7C E0 F0 7C E0 F0 12

Ctrl

Shift

Alt

Satellite E200/205 Maintenance Manual D-7

Appendices Keyboard Scan/Character Codes

Table D-7 No.126 key scan code

Key top

Shift Code set 1 Code set 2

Make Make

Pause Common* E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77

46 C6

*: This key generates only make codes.

D-8 Satellite E200/205 Maintenance Manual

Apx. E Key Layout

Apx. E Key Layout

Appendix E Key Layout

E.1 United States (US) Keyboard

Appendices

Figure E-1 US keyboard

E.2 Japan (JP) Keyboard

Figure E-2 JP keyboard

Satellite E200/205 Maintenance Manual

E-1

Appendices

E.3 Korean (KR) Keyboard

Apx E Key Layout

Figure E-3 KR keyboard

E.4

Canadian Bilingual (QB)

Keyboard

Figure E-4 QB keyboard

E-2 Satellite E200/205 Maintenance Manual

Apx E Key Layout Appendices

E.5 Taiwan (TC) Keyboard

E.6 Thai (TH) Keyboard

Figure E-5 TC keyboard

Figure E-6 TH keyboard

Satellite E200/205 Maintenance Manual E-3

Appendices

E.7 United Kingdom (EN) Keyboard

Apx E Key Layout

Figure E-7 EN keyboard

E.8 UK ENGLISH (CB) Keyboard

Figure E-8 TF keyboard

E-4 Satellite E200/205 Maintenance Manual

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement