Installation Instructions

Installation Instructions
Installation
Instructions
30” Built In Wall Oven
JTP15, JTP17, JTP18, JTP27, JTP45, JTP47, JTP56,
JT910, JT910WA, JT950AA, JT950, ZET737, ZET757
“If you have questions, call 800-GE-CARES or visit our website at:
www.GEAppliances.com”
Before you begin
• Note to Installer- Be sure to leave these
instructions with the consumer.
• OWNER- Keep these instructions for future
reference.
• NOTE- This appliance must be properly
grounded.
Read these instructions carefully and completely
• IMPORTANT-Save these instructions for
local inspector’s use.
• IMPORTANT-Observe all governing
codes and ordiances.
ATTENTION: INSTALLER
All electric wall ovens must be hard wired (direct wired) into an approved
junction box. A “plug and receptacle” is not permitted on these products.
Parts Included
4 screws (single)
8 screws (double)
Materials Needed
Wire Nuts
Bottom Trim
Strain Relief
Clamp
36” of String
Tools You Will Need
1/8” Drill Bit &
Electric or
Hand Drill
Pub. No. 31-10435
229C4053P417-1
Junction
Box
Phillips
Screwdriver
1
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
Electrical
Requirements
For Your Safety
• Be sure your oven is installed properly by
a qualified installer or service technician.
• Be sure the oven is securely installed in a
cabinet that is firmly attached to the
house structure. Weight on the oven door
could cause the oven to tip and result in
injury. Never allow anyone to climb, sit,
stand or hang on the oven door.
• Make sure the cabinets and wall coverings around the oven can withstand the
temperatures (up to 200°F.) generated by
the oven.
This appliance must be supplied with the
proper voltage and frequency, and connected
to an individual, properly grounded branch
circuit, protected by a circuit breaker or fuse,
having amperage as noted on rating plate.
(Rating Plate is located on oven frame.)
We recommend you have the electrical wiring
and hookup of your oven connected by a
qualified electrician. After installation, have the
electrician show you where your main range
disconnect is located.
Check with your local utilities for electrical
codes which apply in your area. Failure to
wire your oven according to governing codes
could result in a hazardous condition. If there
are not local codes, your range must be wired
and fused to meet the requirements of the
National Electrical Code, ANSI/NFPA No. 70Latest Edition. You can get a copy by writing:
National Fire Protection Association
Battery March Park
Quincy, MA 02269
Effective January 1, 1996, the National
Electrical Code requires that new, but not
existing, construction utilize a 4 conductor
connection to an electric range. When
installing an electric range in new
construction, follow the instructions in the
section on NEW CONSTRUCTION AND
FOUR CONDUCTOR BRANCH CIRCUIT
CONNECTION.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz
electrical system. If you connect to aluminum
wiring, properly installed connectors approved
for use with aluminum wiring must be used.
CAUTION: The electrical power
to the oven supply line must be
shut off while line connections
are being made. Failure to do so
could result in serious injury or
death.
2
Installation Instructions
Pre- Installation Checklist
Open the door to the stop position.
ALL INSTALLATION INFORMATION
ON THE FOLLOWING PAGES ARE
TO BE USED FOR SINGLE AND
DOUBLE OVEN INSTALLATION!
Remove packaging materials.
Check behind hinges, and under
false bottom. Remove labels on
door, plastic on trims and panel,
and all tape around oven.
DO NOT LIFT THE DOOR BY THE
HANDLE!
Grasp the door on both sides and
lift up and off the hinges.
Oven Racks
EAS
Y INST
ALL
EASY
INSTALLATION
OFNYOUR NEW
30" ATIO
Before
OF
WAL
30" WALL
OVEN
L OVE YOUR
NEW
N
Broiler Pan
and Grid
IMPORTyou begin-R
IMPORT ANTead
ANT- Save thesethese instruct
Note
OBSERV
to Installer
instruct
OWNER
ions
Before
you begin-Read
these
completely
and carefully.
E instructions
complet
ions
ALL
- Be
- Keep
Notefor local
IMPORTANTSave these
instructions
for local
inspector's
GOVERN
sure
elyuse.
these
This
to leave
and
inspecto
ING
applianc ALL
IMPORTANT- OBSERVE
GOVERNING
CODES
AND
ORDIANCES.
instruct
carefully
CODES
these
e must
.
Note to Installer- Be sure
to leaveions
these instructions
ther's
consumer.
use.
instruct with
AND
for future
be
ORDIAN
ions
OWNER- Keep these instructionsproperly
for future
reference.
referenc with
FOR
CES.
grounde(if applicable).
the
YOUR
Note- This
appliance must be properly grounded
consum
e.
SAFETY
d (if
Before
er.
applicab
instruct you begin-R
le).
carefullyions completead
these
ELECTRICAL REQUIREMENTS
FOR
. YOUR SAFETY
IMPORT
ely and
ELECTR
instruct ANTBefore
begin-Read these
ionsyouSave
Before youICAL
begin-Read
IMPORT
these
REQUIRthese
for local
Before
instructions
completely and
ANTinstructions completely EMENTS
and
GOVERN
OBSERVinspecto
instruct you begin-R
ING
carefully.
Note carefully.
r's use.
E ALL
CODES
carefullyions completead
to Installer
Save
these
these IMPORTANTIMPORTANT- Save these
these
IMPORT .
instruct
- BeforAND
ely and
instructions
local inspector's use.
OWNER
instructions for local
inspector's use.
sure ORDIAN
instruct ANTto leave
OBSERVE
ALLCES.
- Keep ions with
Save OBSERVE ALL
for futureIMPORTANTIMPORTANTthe AND ORDIANCES. IMPORT ions for
these
these CODES
GOVERNING
Notereferenc
GOVERNING
localCODES AND ORDIANCES.
instructconsum
ANTGOVERN
ThisNote to InstallerBe ions
sure toer.
leave
OBSERVinspecto to leave
properly
appliance.
Note
ING to Installer- Be sure
Note
Before grounde
r's
E ALL
these instructions
to theseCODES
e must with the consumer.
instructions
with theuse.
consumer.
these Installer
instruct youOWNERAND
d (if
be instructions
begin-R
Keep
these
instruct
- Be
OWNERKeep these
instructions
applicab
OWNER
sure ORDIAN
carefullyionsfor
ions reference.
futureead
reference.
complet
to leave CES.
these le).
for future
for future- Keep
with
IMPORT . Note- This
elyappliance
the
must be
and
Note-these
This appliance
must be
Notereferenc
instruct ANTinstructconsum
properly
grounded (if applicable). properly
This properly
Save
er.
(if applicable).
e. groundedions
applianc
IMPORT ions for
these
Before
you begin-Read these
Before you begin-Read these
Before grounde
local
e
GOVERNANT- instructions
must
completely and
instructions
completely
and
instruct you begin-R
OBSERVinspecto
d (if
be
ING carefully.
Note
applicab
carefully.
carefullyions complet
CODES E ALL r's use.
ead
to
these le).
these Installer IMPORTANTSave these
IMPORT .
IMPORTANTinstruct - Be AND ORDIAN
ely and Save these
OWNER
sure
for local inspector'sinstruct
use.
ANT- instructions
ionsinstructions
for local inspector's use.
to leave CES.
Save
for future- Keep
with
IMPORTANTOBSERVE ALL IMPORT ions
these
the
IMPORTANTOBSERVE ALL
these
for local
Notereferenc GOVERNING
instructconsum
CODES AND ORDIANCES.
GOVERNANTGOVERNING
This
inspecto CODES AND ORDIANCES.
OBSERV
properly
ions er.
appliance.Note to InstallerING
Note
Be sure to leave
Note E
to InstallerBe sure to leave
r's use.
CODES
grounde e must
to
ALL
these Installer these
these instructions with the consumer.
instructions with the consumer.
d (if
be
instruct - Be AND ORDIAN
applicab Keep these instructions
OWNER
OWNERsure
Keep these instructions
ions OWNERto leave CES.
for future- Keep
with
for futurele).
reference.
reference.
the
these for future
consum
Notereferenc
Note- This appliance must be
instruct
NoteThis appliance must be
This
er.
properly
appliance. properlyions
properly grounded (if applicable).
grounded (if applicable).
grounde e must
d (if
be
applicab
le).
Literature
Pack
Open oven door and remove literature
pack, broiler pan and grid, and oven
racks.
Remove Installation Instruction from
literature pack and read them carefully
before you begin.
Be sure to place all literature, Use and
Care, Installations, etc. in a safe place
for future reference.
NOTE:The oven door is very heavy. Be
sure you have a firm grip before lifting the
oven door off the hinges. Use caution
once the door is removed. Do not lay the
door on its handle. This could cause
dents or scratches
EASY INSTALLATION OF YOU NEW
30" WALL OVEN
Before you begin-Read these instructions completely and carefully.
IMPORTANT- Save these instructions for local inspector's use.
IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave these instructions with the consumer.
OWNER- Keep these instructions for future reference.
Note- This appliance must be properly grounded (if applicable).
FOR YOUR SAFETY
ELECTRICAL REQUIREMENTS
Before you begin-Read these
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave
these instructions with the consumer.
OWNER- Keep these instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
Before you begin-Read these
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave
these instructions with the consumer.
OWNER- Keep these instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
Before you begin-Read these
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave
these instructions with the consumer.
OWNER- Keep these instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
Before you begin-Read these
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave
these instructions with the consumer.
OWNER- Keep these instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
3
(Continued on following page)
Installation Instructions
Pre- Installation Checklist cont.
Place the oven on a table or
platform even with the cutout
opening. (Platform must support
150 lbs. single, 275 lbs double.)
Cover hinge with paper towel rolls
or toweling.
Remove the bottom trim from the
top of the oven. It will be installed at
the end of installation. The trim is
wrapped separately and taped to the
top of the unit.
CAUTION: When the door is
removed and the hinge arms
are at the stop postion, DO
NOT bump or try to move the
hinge arms. The hinges could
snap back causing an injury to
the hands. Cover the hinges with
toweling or empty towel rolls
while working in the oven area.
Bottom Trim
Shipping Location
Side Trim
4
Installation Instructions
A1
Cutouts for Single Built-In-Oven
CUTOUT
WIDTH
28 1/2" MIN.
28 5/8" MAX.
5"
JUNCTION BOX
LOCATION
ALLOW 11/16" FOR
OVERLAP OF THE
OVEN OVER SIDE
EDGES OF CUTOUT
THE OPENING
BETWEEN INSIDE
WALLS MUST
BE AT LEAST
28 1/2"WIDE
22" TO
BOTTOM OF
JUNCTION BOX
CUTOUT
HEIGHT
27 1/4" MIN.
27 5/16" MAX.
21"
ALLOW A MINIMUM
OF 21" FOR CLEARANCE
TO ADJACENT CORNERS,
DRAWERS, WALLS ETC.
WHEN THE DOOR IS OPENED.
ALLOW 1" FOR
OVERLAP
ON OVEN TOP
AND BOTTOM
OF CUTOUT
SUITABLE
BRACING
TO SUPPORT
RUNNERS
21 5/8"
OVER CENTERLINE
OF CABINET
Cutout Depth
23 1/2” Min.
Cutout Width
28 1/2” Min.
28 5/8” Max.
Cutout Height
27 1/4” Min.
27 5/16” Max.
RECOMMENDED
CUTOUT
LOCATION
32 1/2"
FROM THE
FLOOR
NOTE: If the cabinet does not
have a front frame and the sides
are less than
3/4” thick, shim both sides
equally to establish the cutout
width.
CABINET
WIDTH
30"
CL
Cabinet Width
30”
Recommended
Cutout Location
from Floor
32 1/2”
2" x 4" or
EQUIVALENT
RUNNERS
If the cabinet does not have a solid
bottom, then two braces or runners
must be installed to support the
weight of the oven. For single ovens
the runners and braces must
support 150 pounds.
THIS OVEN IS NOT APPROVED FOR STACKABLE
OR SIDE BY SIDE INSTALLATION
5
Installation Instructions
Cutouts for Double Built-In-Oven
A2
CUTOUT
WIDTH
28 1/2" MIN.
28 5/8" MAX.
5"
JUNCTION BOX
LOCATION
ALLOW 11/16"
FOR OVERLAP
OF THE OVEN
OVER SIDE EDGES
OF CUTOUT
ALLOW A MINIMUM OF 21"
FOR CLEARANCE TO
ADJACENT CORNERS,
DRAWERS, WALLS ETC.
WHEN THE DOOR
IS OPENED.
THE OPENING
BETWEEN INSIDE
WALLS MUST
BE AT LEAST
28 1/2"WIDE
ALLOW 1" FOR
OVERLAP
ON OVEN TOP
AND BOTTOM
OF CUTOUT
47" TO
BOTTOM OF
JUNCTION BOX
CUTOUT
HEIGHT
51 13/16" MIN.
51 15/16" MAX.
Cabinet Width
30”
Recommended
Cutout Location
from Floor
12”
Cutout Depth
23 1/2” Min.
Cutout Wdth
28 1/2” Min.
28 5/8” Max.
Cutout Height
51 13/16” Min.
51 15/16” Max.
21"
30"
CABINET
WIDTH
CL
SUITABLE
BRACING
TO SUPPORT
RUNNERS
21 5/8"
OVER CENTERLINE
OF CABINET
RECOMMENDED
CUTOUT LOCATION
12" FROM THE FLOOR
NOTE: If the cabinet does not
have a front frame and the
sides are less than
3/4” thick, shim both sides
equally to establish the cutout
width.
2" x 4" or
EQUIVALENT
RUNNERS
If the cabinet does not have a solid bottom,
then two braces and runners must be
installed to support the weight of the oven.
For double ovens the runners and braces
must support 275 pounds.
6
Installation Instructions
A3
Cutouts For Single Oven Under Counter
Gas or electric cooktops
may be installed over this
oven. See cooktop installation
instructions for cutout size.
See label on top of oven for
approved cooktop models.
Gas and electrical connections
for 30" gas cooktop must be
located in an adjacent accessible
location to the right. For a 36"
gas cooktop the connections
may be made to the left.
240V / 208V
Junction Box
Location
25"
5"
Top and/or side
fillers may be
necessary if
unit is positioned
between existing
cabinets. Be sure
they are attached
securely since
they will anchor
the oven in the
cabinet.
28 1/2" MIN.
28 5/8" MAX.
Allow 11/16"
Overlap Top
of Oven &
Side Edges
of Cutout
27 1/4" MIN.
27 5/16" MAX.
22" MIN.
Above
Support
Platform
36"
Typical
Countertop
Height
24"
3/4" Support
Platform
Required
5 9/16"
Reference dimension
for maximum support height
with typical 36" countertop
height
MUST SUPPORT 150 LBS.
NOTE: This Oven is not approved
to be installed under a Solid Disk,
Induction or Downdraft Modular
Cooktop.
7
Installation Instructions
B
B1
B2
Electrical Connections
Turn off the circuit breaker or remove
fuses to the oven branch circuit.
NEW CONSTRUCTION AND FOURCONDUCTOR BRANCH CIRCUIT
CONNECTION
With the oven in front of the cabinet
opening, on a table or platform, connect
the flexible conduit to the electrical
junction box as shown below. You will
need to purchase a strain relief clamp
to complete the connection of the
conduit to the junction box.
JUNCTION BOX
LOCATION
B3
• When installing in a new
construction, or
• When installing oven in a mobile
home, or
• When local codes do not permit
grounding through neutral:
a.Cut the neutral (White) lead from the crimp.
Re-strip the neutral (white) lead to expose
the proper length of conductor.
5"
Ground
Wires
Ground
Wires
CONDUIT
48 1/2"
LONG
BARE
GROUND
Junction
Box Cover
RED
WHITE
BLACK
PLACE OVEN ON
A SUPPORT
TO ASSIST IN
CONNECTING
CONDUIT
STRAIN RELIEF CLAMP
( NOT INCLUDED )
MUST BE USED
AT JUNCTION BOX
b.Attach the appliance grounding lead (green
or bare copper) in accordance with local
codes. If the residence grounding conductor
is aluminum, see WARNING note.
c.Connect the oven neutral (white) lead to
the branch circuit neutral (white or gray) in
accordance with local codes, using wire
nut.
d.Connect the oven red lead to the branch
circuit red lead and the oven black lead to
the branch circuit black lead in accordance
with local codes, using wire nuts. If the
residence red, black or white leads are
aluminum conductors, see “ WARNING”
note.
e.Install Junction Box Cover.
8
( Continued on Next Page)
Installation Instructions
B
Electrical Connections
OR
Do not shorten the flexible conduit.The
conduit strain Relief Clamp must be
securely attached to the junction box
and the flexible conduit must be
securely attached to the clamp. If the
flexible conduit will not fit within the
clamp, do not install the oven until a
clamp of the proper size is obtained.
THREE-CONDUCTOR BRANCH
CIRCUIT CONNECTION
B3
cont.
When connecting to a 3-conductor
branch circuit, if local codes permit:
a. Connect the bare oven ground conductor
with the crimped neutral (white) lead to the
branch circuit neutral (white or gray in
color), using wire nut.
NOTE TO ELECTRICIAN: The 3 power
leads supplied with this appliance are UL
recognized for connection to larger gauge
household wiring. The insulation of these 3
leads is rated at temperatures much higher
than the temperature rating of household
wiring. The current carrying capacity of the
conductor is governed by the temperature
rating of the insulation around the wire,
rather than the wire gauge alone.
Ground and
Neutral Wires
Junction
Box Cover
WARNING: Improper
connection of aluminum
house wiring to copper leads
can result in an electrical hazard or
fire. Use only connectors designed
for joining copper to aluminum and
follow the manufacturer’s
recommended procedure closely.
b.Connect the oven red lead to the branch
circuit red lead, using wire nut.
c. Connect the oven black lead to the branch
circuit black lead in accordance with local
codes, using wire nut.
d.Install Junction Box Cover.
9
Installation Instructions
C
Securing the Oven
C1
With the conduit connected, the oven
is ready to be slid into the cutout
opening.
C2
a. Loop a 36” string around the conduit
before the oven is slid into place. This
will keep the conduit from falling behind the oven.
Drill four-1/8” pilot holes through the
mounting holes (top and bottom) of the
side trim, for the four #8 screws
provided. Drill eight holes for the
Double Oven.
The screws must be a
minimum of 1/4” from
the front of the cutout.
MOUNTING
HOLE
LOCATIONS
Pull out on
string loop
while pushing
the oven into
the cabinet
NOTE: Mounting screws must be
used. Failure to do so could result in
the oven falling out of the cabinet
causing serious injury.
b. Lift oven into cabinet cutout using the
oven opening as an grip. Carefully
push against oven front frame. Do not
push against outside edges.
c. As you slide the oven back, pull the
string so that the conduit will lie on top
of the oven in a natural loop.
d. When you are sure the conduit is out
of the way, slide the oven all the way
back into the opening. Remove the
string.
C3
Note: Before drilling the pilot holes
make sure the oven is pushed as far
back into the opening as it will go
and centered.
10
Secure the oven to cabinet with screws
provided.
Installation Instructions
D Installing the Bottom Trim
D1
Make sure the flat side is up on the
bottom trim.
D2
Find the Key Slot on the back of the
trim.
D3
Match the key slot with the rivet on the
bottom of the side trim
Key hole slot and wide flange at top
Lower trim mounting rivet on bottom of side
trim.
D4
Push the trim down until it snaps into
place.
Push trim down at both ends until it snaps into
place.
CAUTION: Be sure you do not tip the oven foward during installation or you
may bend the bottom trim. The bottom trim provides an opening for cooling
air to enter the cabinet. This opening should never be blocked.
11
Installation Instructions
E Replacing the Oven Door
E1
Make sure the hinge is in the door stop
position.
E2
Remove the toweling or paper towel holder
from the hinge.
E3
Grasp the door on both sides.
E4
Hold the door over the hinges lining up the
hinges with the hinge slots on the bottom of
the door.
E5
Slide the door down onto the hinges as far
as it will go.
E6
Close the door.
The oven door is heavy. You may need help lifting the door high enough to slide it
down onto the hinges. Do not lift the door by the handle.
12
Installation Instructions
Pre-Test Check List
Remove all protective film if
present, and any stickers.
Check that the bottom trim is installed
properly (see page 11).
Check to be sure that all wiring is
secure and not pinched or in
contact with moving parts.
Check to be sure the mounting
screws are installed and flush with the
side trim, (see page 10).
Operation Checklist
NOTE TO ELECTRICIAN:
The power leads supplied with this
appliance are UL recognized for
connections to larger gauge
household wiring. The insulation of
these leads is rated at temperatures
much higher than the temperature
rating of household wiring. The
current carrying capacity of a
conductor is governed by the wire
gauge and also the temperature rating
of the insulation around the wire.
Remove all items from the inside
of the oven.
Turn on the power to the oven.
(Refer to your Use and Care
Manual.) Verify that the bake and
broil units, and all cooking
functionsoperate properly.
Check that the circuit breaker is
not tripped or the house fuse is
blown.
NOTE: ALUMINUM WIRING
A. WARNING:
IMPROPER CONNECTION OF
ALUMINUM HOUSE WIRING TO
THE COPPER LEADS CAN
RESULT IN A SERIOUS PROBLEM.
B. Splice copper wires to aluminum
wiring using special connectors
designed and UL approved for
joining copper to aluminum and
follow the manufacturer’s
recommended connector
procedure closely.
NOTE:Wire used, location and
enclosure of splices, etc., must
conform to good wiring practice and
local codes.
Check that conduit is securely
connected to the junction box.
See Use & Care manual for
troubleshooting list.
13
NOTES
14
NOTES
15
NOTES
16
Pub. No. 31-10435
229C4053P417-1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement